PROVN OF CERTAIN SANCTION WORK AT (PHASE-II) OF VARIOUS UNITS AT MISA CAMP AREA UNDER GE(S) TEZPUR

Amount

Surface dressing not exc. 150mm deep and getting out in Soft/Loose Soil, complete all as specified and as directed.

Excavation in trenches not exc. 1.5 Metre wide and not exc. 1.50 Metre in depth for foundation etc. or for shafts, wells, cess pits, manholes, pier holes etc. not exc. 10 Sqm on plan and not exc. 1.50 Metre in depth and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in, including Spreading, Levelling, Watering and Well Ramming in Layers not exc. 25 Cm as in Soft/Loose Soil, complete all as specified and as directed.

Removing excavated Material (Soil) not exc. 50.00 Metre and depositing where directed at a level not exc. 1.50 Metre above the starting point, complete all as specified and as directed.

M&L Steel Work in Tubular Trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conform-ing to IS:1161-1979 grade St.-240, complete all as specified and as directed.

S & F framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary gusset plates, riveting, etc. n exc 10 kg each brackets, conforming to Fe-290, Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel'), complete all as specified and as directed.

S & F for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exec 22.50 mm and not exceeding 30 cm long and dia of neck 16 to 20 mm, complete all as specified and directed

S & F of 0.50 mm thick pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F of 0.50 mm thick pre-painted galvalume aluminum zinc coating GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for preparation of steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paints over one coat of red oxide primer complete all as specified and directed

M&L for cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M & L for PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M & L for reinforced cement concrete in M-25 (using 20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete in M-25 (using 20 mm graded stone aggregate) as in columns, pillars, piers, posts and struts etc complete all as specified and directed.

M&L for reinforced cement concrete Design Mix M-25 using 20mm graded stone aggregate as in roof beams, cantilevers, bressummers and lintels over 1.5m span complete all as specified and directed.

M&L for hard core of broken stone or boulders of gauge n.exc 63mm, deposited, spread & levelled in layers n.exc 15 cm thick watered & rammed to true surface complete all as specified and directed.

Use and waste of flat formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter for rough finished surfaces of concrete complete all as specified and directed.

Use and waste of flat formwork to sides of pillars(square, rectangular or polygonal), posts, struts, piers,columns and stanchions for rough finished surfaces of concrete complete all as specified and directed.

Use and waste of flat formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete complete all as specified and directed.

M & L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M & L for TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shapes required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed

M & L for brickwork with subclass ‘B’ old size bricks, straight or curved on plan to any radius exc 6m with bricks roughly cut to radius or bricks with wedge shaped joints built in CM 1:4 complete all as specified and directed.

M & L for brickwork with subclass ‘B’ old size bricks, straight or curved on plan to any radius exc 6m with bricks roughly cut to radius or bricks with wedge shaped joints built in CM 1:6 complete all as specified and directed.

M&L for brick work with sub class- B bricks, straight or curved on plan to any radius in half brick thick walls, built in CM in 1:4 complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying three coats of white wash on walls complete all as directed.

M&L for cement concrete type B-1, 1:3:6 (using 20 mm graded stone aggregate) as in lintels upto 1.5m clear span, steps, seismic and other similar bands coping/cills, bed block for embedding hold fast etc. including necessary form work weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

M&L for cement concrete type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) as in lintels upto 1.5m clear span, steps, seismic and other similar bands coping/cills, bed block for embedding hold fast etc. including necessary form work weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms, moulds mitred/stopped ends etc, complete all as specified and as directed. Note :- Measurment shall be taken only for inner girth.

All as per Items No 29 above but add or deduct for each 25 mm girth or part thereof over or under 30cm, complete all as specified and as directed.

M&L rendering 15mm thick in cement monitor 1: 4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

M&L rendering 15mm thick in cement monitor 1: 6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

M&L for 20 mm thick rendering with cement mortar (1:4) on fair faces of brick work in two layers (10mm & 10 mm) seperately mixed with water proofing compound in top layer as per manufacturer's instructions and finishing the surface even and fair without using extra cement complete all as specified and as directed. Note:- WPC shall be measured and paid seperately under appropiate item.

M & L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed .

M&L 75 mm thick Cement concrete type C2 1:3:6 (using 20 mm graded stone aggregate) as in plinth protection laid in alternate bays (not exceeding 2 Sqm each) and finished cement concrete surface even and smooth without using extra cement and providing joints throughout thickness of plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and two parts of sand by weight complete all as specified and as directed.

M&L for 100mm thick PCC 1:2:4 type D-2 using 40mm graded stone aggregate as in to floors/paths/paving/hardstanding complete all as specified and directed.

M & L for 75 mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in sub base of floors finished even and fair complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M & L for forming 12mm thick expansion joints filled with pre-formed bituminous filler board and top 30mm primed and sealed with sealing compound, Grade ‘A’ for 100 mm (Max) thick concrete slab complete all as specified and directed.

S&F of PVC board /sheets for fabrication of kitchen cabinets of depth 700mm below kitchen platform to be made as per following specification - (a) Main outer body/carcuss shall be made using 18mm thick Pre-laminated plain white solid PVC board of density not less than 550 kg/cum.on top, bottom, LHS & RHS. Backside of main body shall be fixed with 5mm thick PVC plain white sheet. 1x shelves shall be provided using 18mm thick plain white solid PVC board of density not less than 550 kg/cum. (b) 18mm thick prelaminated PVC sheet with decorative finish on one face and other face white having density not less than 600 kg/cum shall be used for shutters on front including lining and lining as required. (c) Backside of main body shall be fixed with 5mm thick PVC plain white sheet. (d) Necessary builders hardware / autohinges is deemed to be included in quoted rate by the contractor.

S&F of PVC board /sheets for fabrication of kitchen cabinets of depth 300mm for Overhang Kitchen Cabinet to be made as per following specification - (a) Main outer body/carcuss on top, bottom, LHS and RHS including shutters shall be made using 18mm thick prelaminated PVC sheet with decorative finish on one face and other face white having density not less than 600 kg/cum complete incl lipping & lining as required. (b) 1x shelves shall be provided using 18mm thick plain white solid PVC board of density not less than 550 kg/cum. (c) Backside of main body shall be fixed with 5mm thick PVC plain white sheet. (d) Necessary builders hardware / autohinges is deemed to be included in quoted rate by the contractor.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking down and refixing in same opening door shutter of any description exc. 1 sqm but not exc. 2 sqm each complete all as specified and directed.

M & L for screed bed or bedding layer of mortar, 20mm thick, in cement mortar 1:6, for laying floor finishes complete all as specified and directed.

M & L for rendering 10 mm thick in cement mortar 1:3 on fair faces of brick or concrete surfaces finished even and rough for receiving wall tiles/dado/skirting complete all as specified and directed.

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc. 0.11 Sqm but not exc. 0.18 sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc. 0.11 Sqm but not exc. 0.18 sqm, as in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

M&L Point wiring with PVC insulated and unsheathed FRLSH cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS - 694 1990 drawn through and including PVC conduit pipe of suitable size with all accessories including PVC box /fabricated MS terminal boxes fixed flush with wall surface for mounting switches, sockets, regulator etc or modular GI boxes of suitable sizes including 1.5 sq mm FRLSH stranded PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly for one light or fan point controlled by one switch single pole one way for light/ ceiling fan/ exhaust fan /call bell point/ Switch socket outlet 5 amps complete all as specified and as directed. Note: Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.

All as per item No. 48 above but one 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed by Engineer-in-charge.

All as per item No. 48 above but one 3 pin 5 amps switch socket commbination on the independent board with other switch complete all as specified and directed by Engineer-in-charge.

M&L fo Point wiring surface type with 2.5 sqmm (Nominal Area) PVC insulated stranded single core unsheathed FRLSH copper conductor cable 1100 Volts grade drawn through with and including PVC casing caping with all fittings and accessories of conduit pipe (like Tee, Bend etc) complete fixed to walls / ceiling etc with and including 2.5 Sqmm (nominal area) PVC insulated unsheathed, stranded, single core FRLSH copper cable as earth continuity wire connecting to common earth point (including supply & fixing of PVC boxes of suitable size for mounting sockets for 5 pin, 16 Amp Switch socket combination on independent board complete all as specified and directed. Note: Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.

Supply and fix switch piano flush type, single pole , 5/6 Amps, one way, complete all as specified and directed.

Supply and fix switch socket combination 2 in 1 multipurpose 5 pin , (6 Amps ) flush type controlled by one switch, complete all as specified and directed.

S&F socket outlets 2 in 1, 3 pin, 5/6 Amps flush type230/240 V complete all as specified and as directed .( For Same Board only)

Supply and fixing switch socket combination 2 in 1 , 6 pin , (16 Amps ) flush type controlled by one switch complete all as specified and directed.

Supply & fix ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps, complete all as specified and directed.

Supply and fix Bldg security light fittings 25 watts, minimumm system lumen output 100 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65 including necessary connection complete suitable for pole dia 25mm complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size, complete all as specified and directed.

Supply and fix 18 W LED light fitting wall mounted batten 4'ft , extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 18 watt,6000K including necessary connection complete all as specified and directed.

Supply and fixed epoxy powder coated sheet metal enclosure for DBs, double door , Single pole and neutral 240 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as specified and directed.

Supply and fixing epoxy powder coated sheet metal enclosure for DBs, double door, Triple pole and neutral 415 V, 4 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact, complete all as specified and directed.

Supply and fix MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessry connection complete all as specified and directed.

Supply and fix MCB SPN 6-32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection, complete all as specified and directed.

Supply and fixing MCB TPN 63 Amps, 'C' series 10kA, 415 Volts and to be housed in DBs complete including necessry connection, complete all as specified and directed.

Supply & fix Heavy Duty Metallic wall mounted ( turbo charge) Fans of 600 mm sweep size, complete all as directed by Engr-in-Charge.

Material and labour for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion.

Supply, laying / fixing / connecting, testing and commissioning of LT under ground cable Size 35 Sqmm X 3.5 Core, XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cable (heavy duty) with multistranded aluminium conductor,1100 Volts grade in trenches/on wall/poles laid in ducts/inside protection pipe of the following cross sectional area including cable glands,lugs and suitable size of MS saddle clips (where ever cable laid in ceilings / walls without cable duct) all as directed by the Engr-in-Charge for the following ratings Note:- (i) Excavation,sand cushioning,brick will be measured and paid separtely.

Supply and laying dry coarse sand as in cushioning of under ground electric cable in trenches, laid to a uniform thickness of 23 Cm (15 Cm under the cable & 8 Cm over the cable) and gently punned down to 18 Cm thickness complete all as specified and as directed by the Engr-in-Charge. Note:- Thickness after punning down shall be measured for payment.

M&L for Brick Sub Class 'B' locally available best quality laid in trenches with width equal to length of the bricks, above sand cushioning for cable protection complete all as specified and as directed.

S&F Pipes galvanized, 50 mm bore “light grade”, supplied and laid complete including necessary fittings such as tees, bends, elbows, sockets, reducers etc as per site requirement, complete all as specified and directed. Note 1:-The contract sum shall be arrived at after deducting amount of schedule of credit from the total quoted amount. Note 2-Contractor's supervisor and main worker would wear shirt/T-shirt of colour sky blue/brown/yellow preferable embossed with contractor's firm name while carrying out any activities in defence area for better check of security purpose. Note 3:-The tenderer (all eligible contractors) shall ascertain the taxes & levies as on date. The subject tender caters all the taxes & levies as on date including the latest notification of GST issued as on date ( issued by Central Board of Indirect Taxes and Customs)

LAXMI & GANESH ENTERPRISE (BID ID -3433765)

BCL (BID ID -3434275)

M/S Jiban Krishan Das and Co (BID ID -3433191)

sanjay upadhya (BID ID -3434215)

DILIP KUMAR SINGH (BID ID -3434507)

M/S SEWAK SINGH (BID ID -3431358)