Repairing & Renovation of Taluka Seva Sadan at Pardi Ta.Pardi, Dist.Valsad. (Repairs to Compound Wall Parking Shed Gate Paver Block & Miscellaneous Work)

Name of Work :-

Repairing & Renovation of Taluka Seva Sadan at Pardi, Ta.Pardi, Dist.Valsad. (Repairs to Compound Wall,

Parking Shed, Gate, Paver Block & Miscellaneous Work)

Bill of Quantities

(A) Percentage Rate Tender (Up to INR 50 Cr. )

Memorandum showing items of work to be carried out

Ite Quantity Unit Estimated Total Amount

Ite Quantity Unit Estimated Total Amount

No. Item of work In figure estimated

Rs. Ps. quantities

1 Excavation for foundation upto 1.50 mt depth including sorting out and 63.0 Cum 117.08

stacking of useful materials and disposing the excavated stuff all lead

& lift(A) Loose or soft soil.

2 Providing and laying cement concrete 1:4:8 (1- Cement : 4- Coarse sand : 18.00 Cum 2660.45

8- graded stone aggregates 20 mm nominal size) and curing complete

excluding cost of formwork in (A) Foundation and Plinth

3 Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand : 27.00 Cum 3683.34

4- graded stone aggregates 20 mm nominal size) and curing complete

excluding cost of formwork in (A) Foundation and Plinth

4 Steel work, welded in built up sections framed work including cutting, 8373.00 KG 90.48

hoisting, fixing in position and applying a priming coat of read lead paint

& two coat oil paint. (A)In beams and joists, channels angles Tees, flats,

with connecting plates or angle cleats as in main and cross beams. Hip

and jack rafters, purlins conneted to common rafters and the like.

5 Providing and fixing of Ridge flashing for roof panel shall be made out of 192.00 Sqm 858.67

0.5 mm thick pre coated GI sheet . The Precoated sheet shall be of

minimum 240 mpa steel grade confirming to IS 14246:1995 and shall

have zinc coating of minimum 120 gsm as per IS:277:1992 , 5-7 microns

epoxy primer on both side of the sheet and polyester top coat 15-18

micron. The PPGI Sheet shall have plastic protective guard film of

minimum 25 microns to avoid scratches during transportation. The ridge

shall be fixed to the steel members by pop rivet or self drilling/self

stitching fastners @ maximum 450 mm c/c along length of

capping/flashing etc complete.

6 Providing and fixing pre-cast Rubber Dye inter locking concrete block 279.00 Sqm 686.90

60mm thick with grade of concrete M300 pnumatic compressed/Vibrated

mechanically and as per approved design confieming to IS 15658:

including 35 mm Sand layer for levelling and filling the joint with sand in

proper line and level as per guidelines of IRC : SP 63-2018 etc complete.

7 Applying priming coat over new steel and other metel surface after and 314.00 Sqm 122.49

including preparing the surface by throughly cleaning, oil,grease, dirt and

other foreign matter and scoured with brushes fine steel wood, scrapers

and sand paper with ready mixed priming paint brushing red lead.

Painting two coats (excluding priming coat) on new steel and other metal

surface with enamel paint, brushing, interior to give an even shade

including cleaning the surface an even shade including cleanicn the

surface of all dirt, dust and other foreign matter.

8 Providing and laying Vitrified tiles 8 to 10 mm thick , 24''x 24'' in flooring 315.50 Sqm 1073.13

treads of steps and landing laid on a bed of 12mm thick cement mortar

1:3 (1-cement : 3-coarse sand ) finishing with flush pointing in white

9 Providing and fixing FRP frame size 125x65 mm and 35mm thick FRP 13.00 Sqm 2019.98

shutter with wood grain raised panneled design finish shutter having

extra reinforcement on sides & edges in Gel coat finish. The core of the

shutter & frame is to be filed up with injected polyurethene foam done in

situ alongwith embedded wooden pieces for stiffening & also taking

hinges & fintures. The whole FRP frame & shutter is to be water proof

weather proof, termite proof & resistance to mild acid/alkali. Rates are to

be inclusive of S.S hinges with fastener sleeve & alluminium fixtures &

In Words Sixteen Lakh Seventy Two Thousand One Hundred Seven Rupees And Twenty Two Paisa Only.

I/We am /are willing to carry out the work at…………% above/below percent (should be written in figures and words) at the

estimated rates mentioned above amount of my/your tender works out as under.

*Estimated Amount *Estimated Amount

put to Tender Rs. 1672107.22 put to Tender Rs.

Deduction …………….. % below………………… Add ………… % above Rs. …………….

1 The Contractor shall be exhibit board as per government circular No.BDG/3277/1657 N dated 26/01/1997 S (M.GUJ) with

detailed specification and details of work and amount Involved at site without any payment as directed by Engineer-In-

2 All work shall be carried out as per public work department hand book and other specifications of Division or as directed.

3 All columns in the Schedule should be filled in ink & the total of the entries in the last column should be struck by Contractor

under his sign.

4 Rates quoted include clearance of site (Prior commencement of work and its close) in all respects and hold good for work

under all condition, site, moisture/ weather etc.

5 The Boards stating the detailed specification & detailes of Work shal be provided by the contractor as per Government

Resolution T.No.1890-240- Dtd.18/11/1990 and directed by contractor at his own cost immediately on recommanding the

6 Testing of Material Shall be done as per the statement attached with specification,The material IS Tested in GERI by

Executive Engineer Surat and Bill for the testing charges shall be paid by Executive Engineer,1% of the Amount put to

7 1% of the Construction Cost Shall be deducted from the bill Amount of the contract as per the Buildig and other

Construction works walfare cess at 1996(Labour and Employment Department Letter No CWA-2004-1831-M(3)Dated

9/12/2005 notification Of Labour & Employment department dt.03/01/2005 & Labou & Employment Department Letter no

8 In Case of RCC items Where there is a change in Grade of Mix or Change as per Actual Mix design the cost of difference of

Cement Difference shall be deducted from the rate of original item at the rate of star rate mentioned in the tender.

9 Contractor are advised to visit site before loading tender rate.

10 Necessary wiring point and drainage point are installed at Site however any modification in electrical installation and

drainage & water supply connection and minor correction to perform experienced in Lab shall be done by contractor at his

11 The Rates are inclusive of all the taxes (Excluding GST),Transport Charges,Octroi duty and storage Charges up to date.

12 The materials Covered for wiring should be got approved from the Engineer Incharge of the work.

13 GST and Income tax TDS will be deducted at a source while making payments of bills.

14 GST will be paid extra as per Govt. amendment.

15 The Materials on the work shall have to be used and carried out as specified in technical note.

I/We hereby Declare that I/we have Visited the site and fully Exquisite myself/ourselves with the local situation regarding

(A) materials,Labour and other factors pertaininfg to work before submitting tender.

I/We hereby Declare that I/we have carefully Studied the condition of Contracts,Detailed Specification and other tender

Document of this work and agree to execute the same accordingly.

Deputy Executive Engineer

Valsad (R&B) Sub-Division

Signature of Bidder

Executive Engineer

Valsad (R&B) Division