WELCOME MAINTENANCE AND PERIODICAL SERVICES TO CERTAIN BUILDINGS AND REPAIRS TO ROOF WPT, SUNKEN SLABS OF TOILETS, ALU/ WOODEN JOINERY, INTERNAL WATER SUPPLY LINEAS AND WASTE WATER PIPES, ROLLING SHUTTERS AND ROOF WPT AT NAD BHEEMUNIPATNAM, VISAKHAPA

Amount

Demolition of cement concrete (un-reinforced) in ground floor and paving n.exc 15cm below or above ground level including removal of demolished materials from work site complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish of the premises complete all as specified and as directed.

Taking down cement plaster of any description on brick work/stone work incl raking out joints, hacking for key ,scrubbing down with water etc and removing rubbish from site of work complete all as directed.

Hacking out old broken glass any thickness size quality or description from /wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed.

Taking down existing roof treatment including plaster etc complete all as specified and as directed.

M&L for Brushing neat cement slurry with 3.0 Kg of cement per Sq m

M&L 15 mm thick rendering on fair faces of brick/concrete surfaces in cement mortar 1:4 in two layers of 10mm thick and 5mm thick, finished fair and smooth and water proofing compound shall be added on top layer as per manufacturer instruction complete all as specified. (Note :- WPC will be measured and paid separately under appropriate item as supply only).

M&L for APP based polymeric membrane minimum weighing 3 Kg/Sq.m. and minimum 3mm thick reinforced with polyester non wove fabric (weight not less than 150 gms/Sq.m.) laid on primed surface after applying a coat of blown bitumen 85/25 grade @ 1.20 Kg/Sq.m. over bitumen primer @ 0.50 Kg per Sq.m. by forced application, applying another coat of hot blown bitumen 85/25 grade @ 1.20 Kg per Sq.m. over water proofing membrane and applying a coat of solar reflective bituminous aluminium paint @ 0.10 Kg per Sq.m. all as per the manufacturers instructions, complete all as specified and directed by the Engineer-in-Charge.

Supply only Integral Water Proofing Compound (ISI marked) of approved make.

Taking down door chowkat or frame with shutter area n. exc 1.5 Sqm each (without taking off shutters from the frame) and removing to store complete all as specified and directed.

Taking down chowkats or frame with shutter, (without taking off shutter from the frame) exc 1.5 Sqm but n.exc 4sqm each and removing from site complete all as specified and as directed.

Taking down shutters of any description n exc. 1.00 Sqm each and removing from the site, complete all as specified and as directed.

Taking down shutters of any description exc. 1.00 Sqm but n. exc. 2.00 Sqm each and removing from the site, complete all as specified and as directed.

Taking down and refixing shutters of any description exc. 1.00 Sqm but n. exc. 2.00 Sqm each and refixing in the same opening, complete all as specified and as directed.

Taking up or down 15mm dia. steel tubing and connections including for removal from site complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 20mm dia. steel tubing and connections including for removal from site complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 25mm dia. steel tubing and connections including for removal from site complete all as specified and as directed by the Engineer-in-Charge.

Taking down PVC (SWR) pipes (of any radius) including joints, etc complete all as specified and as directed by the Engineer-in-Charge.

Demolition of Brick work or stone boulders masonry built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and as directed

M&L Brick work with fly ash bricks straight or curved on plan exc 6.0 mtr mean radius built in cement mortar (1:6) complete all as specified and as directed

M&L for post construction anti termite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia. holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed by the Engineer-in-Charge.

M&L for post construction anti termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia. holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed by the Engineer-in-Charge.

M&L for post construction anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed by the Engineer-in-Charge.

M&L for grouting of floor slab with cement slurry by mixing 50 kg of cement with 18 to 22 litre of water with admixture of FOSROC CEBEX 100 (Plasticized expanding grout admixture) about 225 gms per 50 kg of cement by drilling upto 12 mm dia hole in floor @ 300 mm C/C upto required depth and grouting / pumping the grout with mechanically powered grout mixer upto 10 kg for each hole as per manufacturer ‘s instructions and sealing the hole after grouting (GROUT = WATER + CEMENT + FOSROC CEBEX 100 in proportion) complete all as specified and as directed by the Engineer-in-Charge.

M&L for sealing of floor/ wall tile joint with NITOLITE GROUT (Cementing tile joint filler) by uniform paste prepared with one part of water to 3 part of powder by volume all as per manufacturer’s instructions complete all as specified and as directed by the Engineer-in-Charge.

S&F 2nd class hard wood (well seasoned) plain, solid, straight, chowkats and frame, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified.

S & F 35mm thick 2nd class hard wood plain, framed, panelled shutters (any number panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density ,wood particle board with commercial face veneers supplied and fixed to chowkats complete all as specified and directed.

M&L 35mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. divided into squares (without sash bar), with plain chamfered or rounded, mitred and rebated edges of framing plain any numbers of members of shutter as specified in SSR-I , Section 8,clause 8.24(a), complete all as specified and as directed.

M&L 30mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. divided into squares (with sash bar), with plain chamfered or rounded, mitred and rebated edges of framing plain any numbers of members of shutter as specified in SSR-I , Section 8,clause 8.24(a), complete all as specified and as directed.

S&F 30 mm thick flush shutter solid core construction, with block board core and plywood face panels commercial type on both sides with 6 mm thick teak wood beading all round complete all as specified and as directed.

M&L 18/ 19 mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including teak wood lipping 6mm thick all round complete all as specified and as directed.

S&F solid PVC door frames of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified & directed

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail & bottom rail on either side & gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame, welded/sealed to the stiles & rails with suitable PVC sheet beading & jointed together with solvent complete all as specified & directed.

S&F 75mm size MS butt hinges medium weight cold rolled fixed to frame complete all as directed.

S&F 125mm size MS butt hinges medium weight cold rolled fixed to frame complete all as directed.

S&F 75mm size SS butt hinges medium weight cold rolled fixed to frame complete all as directed.

S&F 100mm size SS butt hinges medium weight cold rolled fixed to frame complete all as directed.

M&L 200 mm long , aluminium alloy barrel tower bolts anodised extruded section ISI marked complete all as specified.

S&F in repair 200 mm long , aluminium alloy barrel tower bolts anodised extruded section ISI marked complete all as specified.

M&L 150 mm long , aluminium alloy barrel tower bolts anodised extruded section ISI marked complete all as specified.

M&L 100 mm long , aluminium alloy barrel tower bolts anodised extruded section ISI marked complete all as specified.

S&F in repair 100 mm long , aluminium alloy barrel tower bolts anodised extruded section ISI marked complete all as specified.

S & F 150mm size aluminium handles, cast type, anodised complete all as directed.

S & F in repair 150mm size aluminium handles, cast type, anodised complete all as directed.

S & F 125mm size aluminium handles, cast type, anodised complete all as directed.

S & F 100mm size extruded aluminium handles, fabricated type, anodised complete all as directed.

S & F in repair 100mm size extruded aluminium handles, fabricated type, anodised complete all as directed.

S&F 300mm long aluminium anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and as directed.

S&F in repair 300mm long aluminium anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and as directed.

S & F 300mm mild steel, ordinary rat tail, rod pattern springs including roller and roller plate, complete all as specified and as directed

S & F in repair 300mm mild steel, ordinary rat tail, rod pattern springs including roller and roller plate, complete all as specified and as directed

S&F Hasp and staple aluminium anodised 100mm safety type with mild steel hinge pin including bolt to hinge plate and fixed with screw complete all as specified and as directed

S & F in repairs mortice lock with 4 lever vertical type brass body 100mm long suitable for single shutter aluminium door complete all as specified and as directed

S&F harrison rail, aluminium alloy anodised with fixing brackets, stops, rollers etc in curtain rails complete all as specified and as directed.

S&F in repairs aluminium (Die-cast) body door closer hydraulically regulated, designation No. 3 universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg complete all as specified and as directed.

S&F aluminium XPM wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed.

S&F in repair aluminium XPM wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed.

M&L for repairs and servicing of rolling shutters and removing of worn out components such as hood covers, laths, ball bearings, helical wire springs, lock plates, brackets plates, shaft rods etc., straightening of existing guide channels, gear boxes, lath, hood etc. at required places including greasing and refixing in the same opening after repairs complete all as specified and as directed by the Engineer-in-Charge. Note: Spare parts shall be measured and paid separately under respective items.

M&L for repairs and servicing of boom barriers at required places including greasing and refixing in the same opening after repairs complete all as specified and as directed by the Engineer-in-Charge.

Supply only interlocking lath sections made out of mild steel strips 1.25mm thick with the continuous section of lath in single piece without any welded joints and each alternate lath section fitted with malleable cast iron or mild steel clips screwed/riveted at either ends complete all as specified.

Supply only bevelled gear as required at site complete all as specified.

Supply only mild steel hood covers 1.00mm thick bent to shape to match with the existing trackers including stiffeners with MS flat iron complete all as specified.

S & F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc, (minimum thickness of powder coating 50 micron) complete all as specified and as directed.

S&F anodised powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws anodised aluminium fittings such as peg stays 150 mm long (1 No.) , hinges type B-21, 100mm long (2 Nos), tower bolt 75 mm (2 Nos), suitable handle (1 No.) complete all as specified (minimum thickness of powder coating 50 micron) complete all as specified and as directed by the Engineer-in-Charge.

S&F anodised powder coated aluminium window and ventilator shutters, sliding type without sash bars, aluminium sections including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws and suitable anodised aluminium handles and rollers complete all as specified (minimum thickness of powder coating 50 micron) complete all as specified and as directed by the Engineer-in-Charge.

S&F anodised coloured aluminium grill of design No. DG-117, 10mm thick of DECOGRIL or equivalent make as approved by GE fixed with and including 'F' sections complete all as specified and as directed by the Engineer-in-Charge.

M & L 40 mm thick cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in flooring and finishing the cement concrete surface even and smooth without using extra cement complete all as specified and as directed.

M & L 25 mm thick cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in sub base of floors complete all as specified and as directed.

M & L for Non skid/ matt finish ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exc 0.38 Sqm (600 mm x 600 mm) (Ist quality) as in floor set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 15mm thick screed bed in CM 1:4 finished even and rough complete all as specified and as directed.

M & L for Non skid/ matt finish ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 Sqm (400 mm x 400 mm) (Ist quality) as in floor set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 15mm thick screed bed in CM 1:4 finished even and rough complete all as specified and as directed.

M & L for Non skid/ matt finish ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exc 0.38 Sqm as in vertical surface such as skirting/dado set in neat cement slurry and pointed in coloured cement to match the surface, including 10mm thick rendering to receive tiles in CM (1:3) finished even and rough complete all as specified and as directed.

M & L for Non skid/ matt finish ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 Sqm as in vertical surface such as skirting/dado set in neat cement slurry and pointed in coloured cement to match the surface, including 10mm thick rendering to receive tiles in CM (1:3) finished even and rough complete all as specified and as directed.

M & L for glazed ceramic coloured tiles 300 x 450 x 8mm thick (Ist quality) conforming to IS-13753, as in vertical surface such as skirting/dado set in neat cement slurry and pointed in coloured cement to match the surface, including 10mm thick rendering to receive tiles in CM (1:3) finished even and rough complete all as specified and as directed.

M&L 18-20mm thick granite (of any type) work table rubbed and polished in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 20 mm thick screed bed in CM 1:4 complete all as specified and as directed.

M & L rendering 10mm thick on fair faces of brick wall or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick with CM 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L for rendering 5mm thick on fair faces of concrete surfaces of ceilings in CM 1:3 and finished even and smooth with out using extra cement complete all as specified and directed by the Engineer-in-Charge.

M&L for preparation of old treated surfaces of walls and applying one coat of white wash, complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of old treated surfaces of ceiling and applying one coat of white wash, complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of new surfaces of ceiling and applying two coats of white wash, complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of old treated surfaces of walls and applying one coat of oil bound distemper complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed.

M&L for preparation of old treated surfaces of walls and applying one coat of plastic emulsion paint complete all as specified and as directed.

M&L for preparation of old treated surfaces of external walls and applying one coat of cement based paint complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement based paint over one coat of primer complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of old treated surfaces and applying one coat of weather proof exterior emulsion paint on external surfaces of walls complete all as specified and as directed by the Engineer-in-Charge.

M&L for complete removal of the existing treatment on the wall surfaces and applying two coats of weather proof exterior emulsion over one coat of primer complete all as specified and as directed by the Engineer-in-Charge.

S&F 4mm thick sheet glass, pin headed type & glazing with oil putty in square n exc. 0.5 sqm in each pane complete all as specified.

S&F 4mm thick sheet glass, pin headed type & glazing with oil putty in square exc. 0.5 sqm in each pane complete all as specified.

M&L preparation of new wooden surface of any description not otherwise described and exc 10cm width or girth applying two coats of synthetic enamel paint first grade quality over a coat of pink primer, complete all as specified and as directed.

M&L preparation of old wooden surface of any description not otherwise described and exc 10cm width or girth applying one coat of synthetic enamel paint first grade quality complete all as specified and as directed.

M&L applying one coat of synthetic enamel paint including preparation of old steel surfaces over 10 cm width or girth, complete all as specified and as directed.

M&L applying one coat of aluminium paint including preparation of old steel surfaces over 10 cm width or girth, complete all as specified and as directed.

S&F 20 mm dia (15mm internal dia.) 3-layer PP-R polypropylene random copolymer pipes SDR 7.4 & SDR 11 UV stabilised and antimicrobial welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F 25 mm dia (20mm internal dia.) 3-layer PP-R polypropylene random copolymer pipes SDR 7.4 & SDR 11 UV stabilised and antimicrobial welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F 32 mm dia (25mm internal dia.) 3-layer PP-R polypropylene random copolymer pipes SDR 7.4 & SDR 11 UV stabilised and antimicrobial welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, bib taps 15mm dia. fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair two way bib cock 15mm dia. chromium plated, fancy type of make Jaquar Catalogue No.FON-40041 or equivalent in CERA complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair concealed type 15mm dia stop valve cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed

S&F in repairs, 15mm dia. chromium plated angle stop valves, fancy type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 15mm dia. chromium plated pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge.

S & F in repairs 15mm bore Chromium Plated wash hand basin mixer for mixing hot and cold water screwed down for iron pipe complete all as specified and as directed.

S&F in repairs, health faucet 15mm dia. with one meter long easy flex tube in chromium finish and wall hook complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, 125mm dia. chromium plated brass shower rose with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, tubular towel rail stainless steel, 20mm dia., 60cm long between flanges complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, towel ring round with round flange complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair 25mm dia. PP-R globe or gate valve with steel ball, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge.

S & F in repairs 1mm thick stainless steel kitchen sink conforming to IS: 13983 with drainage board of 915mm x 460mm over all size and 410 x 330 x 160 mm bowl size with plugs wastes and washers including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe complete all as specified and as directed.

S & F in repairs 1mm thick stainless steel kitchen sink conforming to IS: 13983 without drainage board of 495mm x 420mm over all size and 410 x 330 x 160 mm bowl size with plugs wastes and washers including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe complete all as specified and as directed.

S&F in repair vitreous china squatting pan Orissa Pattern of size 580x440mm white with integal foot rest 1st quality with 100 mm dia 'P' or 'S' trap, ISI marked including provision of lime concrete bedding excluding flush pipe complete all as specified.

S & F in repair vitreous china, water closet pedestal pattern (white) 'P' trap including fixing flush pipe, fixing bolt and fixing of seat cover complete all as specified and as directed.

S&F in repair plastic seat cover, white colour, closed pattern with flat bottom and cover with mild steel chromium plated or aluminium hinges, devices fixed complete all as specified and as directed.

S&F in repairs vitreous china urinal half stall type flat back white grating and union for discharge pipe, including providing and fixing plugs, bedding urinal against wall in CM (1:2) including 60mm brass screws, etc pointing around urinal back in cement including waste pipe and grating complete all as specified and as directed.

S&F in repairs, wash hand basin of size 550x400 vitreous China (flat back or angle back type) including half pedestal and cutting for and pinning in ends of brackets or erecting stand including supply and fixing of waste coupling, waste pipe etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F 10 ltr capacity, PVC low level flushing cistern, syphonic action type white body with inlet ball valve, float , handle, bracket or erecting stand including supply and fixing of waste coupling, waste pipe etc complete & connecting to WC complete all as specified.

S&F in repair PVC flexible connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed by the Engineer-in-Charge.

S&F 40mm dia. PVC waste pipes for WHB/sink fixed to walls including fittings and connecting to multiple floor trap complete all as specified and as directed by the Engineer-in-Charge.

S&F 50mm dia. PVC waste pipes for WHB/sink fixed to walls including fittings and connecting to multiple floor trap complete all as specified and as directed by the Engineer-in-Charge.

S&F toilet paper holder brass chromium plated fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed by the Engineer-in-Charge.

S&F soap dish, chromium plated brass, of approximate size 160x160x90mm, fixed to plugs with chromium plated brass screws complete all as specified and as directed by the Engineer-in-Charge.

Checking the leakage and petty repairs to wall mixer, WHB mixer, sink mixer, bib taps, pillar taps, stop cock, concealed stop cock , angle valves, gate valves etc of any description or size for stopping leakage of water by changing washers, etc complete all as specified and as directed by the Engr-in-charge. Note : Rates quoted by the contractor are deemed to be inclusive of necessary tools and plants incl materials viz. GI nipples, GI socket , GI union/ Dhaga/ safeda/ M seal/ taflon tape/ solvent/ screws/ white cement/ nails, screws/ gitties etc as required to complete the job

S&F in repair 500 Litres capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) two layered ISI marked hoisted and fixed in position complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair 1000 Litres capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) two layered ISI marked hoisted and fixed in position complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair 2000 Litres capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) two layered ISI marked hoisted and fixed in position complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair PVC water tank cover to match with the existing tank complete with locking arrangement suitable for 500 to 2000 litres capacity complete all as specified and as directed.

Disconnecting existing tank of exc 500 ltrs & n exc 1000 ltrs capacity ,setting aside (or lowering if required) for repair ,cleaning etc and hoisting if required reconnecting and re-fixing in position (Cleaning,repairing,etc measured separately) complete all as specified and as directed.

M&L for cleaning and removing all scale and dirt, etc, from PVC water tanks and from mouths of circulating pipes, etc for exc 250 ltr but n exc 500 ltrs capacity complete all as specified and as directed.

M&L for cleaning and removing all scale and dirt, etc, from PVC water tanks and from mouths of circulating pipes, etc for exc 500 ltr but n exc 1000 ltrs capacity complete all as specified and as directed.

M&L for cleaning and removing all scale and dirt, etc, from PVC water tanks and from mouths of circulating pipes, etc for exc 1000 ltr but n exc 2000 ltrs capacity complete all as specified and as directed.

S&F PVC (SWR) pipes 110mm dia. single docketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC (SWR) pipes 75mm dia. single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by the Engineer-in-Charge.

S&F 110mm dia. PVC (SWR) plain bends any radius complete all as specified and directed by the Engineer-in-Charge.

S&F 75mm dia. PVC (SWR) plain bends any radius complete all as specified and directed by the Engineer-in-Charge.

S&F 110mm dia. PVC (SWR) bends any radius provided with access door complete all as specified and directed by the Engineer-in-Charge.

S&F 75mm dia. PVC (SWR) bends any radius provided with access door complete all as specified and directed by the Engineer-in-Charge.

S&F 110mm dia. PVC (SWR) junction single (Single T) equal or unequal provided with access door complete all as specified and directed by the Engineer-in-Charge.

S&F 75mm dia. PVC (SWR) junction single (Single T) equal or unequal provided with access door complete all as specified and directed by the Engineer-in-Charge.

S&F PVC (SWR) vent cowls 110mm dia. complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair PVC (SWR) multi floor trap 75mm dia. outlet with grating including jointing with solvent cement complete all as specified and directed by the Engineer-in-Charge.

S&F in repairs, PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed by the Engineer-in-Charge.

S&F grating doom 125mm dia. with waste hole of PTMT (Min weight 40 gms) complete all as specified and as directed by the Engineer-in-Charge.

Repairs to low/ high level flushing cistern siphon, washers, handles, float valves, stopping leakage of down pipe by applying M-seal and other related works to make the flushing cistern functional complete all as specified and as directed by the Engr-in-charge. Note : Rates quoted by the contractor are deemed to be inclusive of necessary tools and plants incl materials viz. GI inlet, ball valve, float and handle including brackets and flush pipe of polyethelene of low or high density or PVC 32 mm dia etc as required to complete the job

M&L for repair to the existing floor trap by demolition of PCC including tiles & screed bed for the floor area of 200 mm x 200 mm around the floor trap, provision of 110 mm dia PVC (SWR) pipe vertically for the depth of 20 to 30 cm from the floor level upto the trap embedded in PCC 1:2:4 type B1 and making good with the existing floor finish including provision of grating complete all as specified and as directed by the Engr-in-charge.

Dismantling of wall and ceiling boards (fiber, pulp insulation etc) or insulation board /slab/blankets any thickness including cover fillets, including removing of dismantled material from work site all as directed.

S&F anodised aluminium size of snap grid 605x605mm frame work for false ceiling complete all as specified and as directed

M&L for Gypsum boards 12mm thick in false ceiling fixed with screws in GI frame work fixed with anchor fasteners and applying two coats of oil bound distemper over one coat of primer complete all as specified and directed by the Engineer-in-Charge.

M&L for applying two coats of oil bound distemper over one coat of primer on false ceiling

S&F in repair 32mm dia and 75 cm long PVC waste pipes for WHB complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs, bib taps 15mm dia. of PTMT complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair 32mm dia waste coupling of PTMT (half or full threaded) minimum weight 45gms for WHB/ sink complete all as specified and directed.

S&F in repair 32mm dia waste coupling of PTMT (half or full threaded) minimum weight 45gms for urinal complete all as specified and directed.

M&L for welding in repair in any situation and in any postion such as hinges and similar articles etc for steel door, gates, window, ventilators and grills etc for upto four storey building complete all as specified and directed.

Repairs of air lock, blockage of water pipes from OHT tanks to supply point and repairs/ adjustment to float valves, applying M-seal in tanks and all other connected works of water supply from over head storage tanks/ PVC tanks complete all as specified and as directed by the Engr-in-charge. Note : Rates quoted by the contractor are deemed to be inclusive of necessary tools and plants incl materials viz. GI nipples, GI socket , GI union/ Dhaga/ safeda/ M seal/ taflon tape/ solvent/ screws/ white cement/ nails, screws/ gitties etc as required to complete the job

ARKA CONSTRUCTIONS