SPECIAL REPAIRS TO BLDG NO. P-47 OF 581 LT REGT UNDER GE 863 EWS

Amount

Demolition of cement concrete (unreinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) complete all as specified.

25mm thick levelling course in cement concrete 1:2:4 type B-0, (using 12.5 mm graded stone aggregate) complete all as specified.

Vitrified ceramic tiles (light shade), 10 mm thick (square/ rectangular) polished ,area of each tile not exc. 0.36 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified.

Vitrified ceramic tiles (light shade), 10 mm thick (square/ rectangular) polished, in vertical surfaces, over and including 10 mm thick plaster in cement mortar 1:6 as backing of wall tiles etc., set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified.

Non-skid coloured ceramic tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sq m but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified.

Non-skid coloured ceramic tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

Glazed coloured ceramic tiles 300x200x7 mm thick, in vertical surfaces, over and including 10 mm thick cement plaster in cement mortar 1:6 as backing of wall tiles etc., set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified.

Chequered cement concrete tiles 300x300x25mm thick, with grey cement and pigments, set, jointed and pointed in neat cement slurry ,over and including 20 mm thick screed bed or bedding layer of cement mortar 1:6, in floors complete all as specified.

50 mm thick cement concrete 1:3:6 type C1, (using 20 mm graded stone aggregate), as in plinth protection, finishing cement concrete surface even and fair without using extra cement complete all as specified.

Taking down cement plaster, any description, including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified.

15mm thick rendering in cement mortar 1:6 on brick or concrete surface of any description, surface finished even and smooth without using extra cement complete all as specified.

15mm thick rendering on fair faces of brick work, concrete surfaces in cement mortar 1:4 mixed with liquid WPC, finished even and fair, complete all as specified. (Note : Supply only liquid WPC shall be measured and paid for separately under relevant item)

Supply only liquid water proofing compound, complete all as specified.

Preparation of new plastered wall surface and applying two coats of oil emulsion distemper with hand roller over a coat of primer over 1mm thick white cement based wall care putty complete all as specified.

Complete removal of existing treatment of wall surface and applying two coats of oil emulsion distemper with hand roller over a coat of primer over 1mm thick white cement based wall care putty complete all as specified.

Complete removal of existing treatment on walls including washing down, rubbing down and applying two coats of 100% weather proof exterior acrylic emulsion paint over a coat of primer complete all as specified.

Preparation of new plastered surface on walls and applying two coats of 100% weather proof exterior acrylic emulsion paint over a coat of primer complete all as specified.

Preparation of new plastered surface of wall and applying two coats of white wash complete all as specified.

Dismantling framed work timber scantlings 40 sq. cm and over in section, in any position complete all as specified.

Rolled mild steel Fe -290(Gde E-165) for roof trusses (framed), trussed, purlins, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.complete all as specified.

Dismantling of wall and ceiling boards( fibre, pulp, insulation etc.) or insulation boards/ slabs/ blankets, any thickness including cover fillets complete all as specified.

10 mm thick PVC insulation panels with EPS stuck to 1 mm plain PVC sheet suitably placed in false ceiling, including GI frame work for seamless ceiling grid frame work, size of grid 605 X 605 mm for false ceiling, hangers 6 mm dia GI (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 X 3 mm size 60 mm long complete all as specified.

Dismantling of plain or corrugated steel sheeting, any guage, thickness from roof covering complete all as specified.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified.

Wire netting of galvanised steel wire 1.40mm dia and size of mesh 25 mm fixed with tinned tacks of wire staples complete all as specified.

Taking down chowkats or frames not exc. 1.5 sq.m with shutter (without taking off shutters from the frames) complete all as specified.

Taking down chowkats or frames exc 1.5 sq. m but not exc 4 sq. m with shutter (without taking off shutters from the frames) complete all as specified.

Taking down shutter exc 1.0 sqm but not exc. 2.0 sq.m each complete all as specified.

2nd class hard wood factory made plain, solid, straight chowkats and frames , wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified.

2nd class hard wood factory made 35 mm thick plain, framed, panelled shutters (any no of panels) with panels of timber flat on both sides (feather edge) or of veneered particle board medium density, wood particle board with commercial face veneers; supply and fix two chowkats complete all as specified.

2nd class hard wood factory made 30 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in MES Schedule Part-I, section 8, clause 8.24 (a) supplied and fitted to chowkat complete all as specified.

Solid PVC door frame of size 50mm x 47 mm made out of 5mm plain colour PVC printed sheet & edges painted to match with printed sheet ,reinforced with M.S. square tube, in opening as per specification & drawing complete all as specified.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and Plain colour PVC sheet & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900) used instead of exposed portion of PVC sheet beading in the frame at site as per specification & drawing complete all as specified.

Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified.

Preparation of wood or wood based surfaces of any description new or previously untreated surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

Preparation of old wood or wood based surfaces of any description over 10 cm width or girth and applying a coat of synthetic enamel paint complete all as specified.

Preparation of old steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified.

4mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified.

300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified

Cold rolled mild steel medium weight butt hinges 100 mm long complete all as specified.

200 mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified.

150 mm long aluminium handles, cast type, anodised complete all as specified.

300mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified .

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified.

Pre-cast cement concrete block masonry with solid block exc 10 cm in width type C1 1:3:6 (using 20 mm graded stone agg) set in CM 1:6 complete all as specified.

PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in coping to retaining wall/steps complete all as specified.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified.

Reinforced cement concrete (Nominal Mix) 1:2:4 Type B1 (using 20 mm graded stone aggregate) as in lintel over 1.5 m span, beam etc complete all as specified.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Use and waste of formwork to chajjas and similar work; complete all as specified.

Vitreous china squatting pan 'Orissa pattern' size 580X 440 mm white with integral foot rest including connection to trap,and to flushing pipe, anti-siphonage pipe, etc. complete including making good to floor fixed in repair complete all as specified.

Vitreous china wash down water closet pan (pedestal pattern), white, including flush pipe of polyethylene of low or high density or PVC 32 mm dia., plastic water closet seat closed pattern with cover and hinging device and trap with connection fixed in repairs complete all as specified.

Chromium plated jet for EWC complete all as specified.

PVC valveless, syphonic action type, flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets and connections to pipes fixed in repairs complete all as specified.

Vitreous china wash basin, white, flat back, size 550 X 400 mm including fixing with brackets, 32 mm chromium plated waste fitting with long screwed shanks and fly-nuts complete all as specified.

PVC connections 15 mm size 600 mm long with PTMT nuts fixed in repairs complete all as specified.

Low density polyethylene (LDPE) pipes, 32 mm bore, of pressure rating 6 Kgf/ Sqcm as in waste pipe fixed in repairs complete all as specified.

Bib taps, cast copper alloy, fancy type, chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15 mm bore steel tube fixed in repair complete all as specified.

Central hole wash hand basin mixer pop-up chromium plated quarter turn complete all as specified. Make: Jaqar Model : CON-CHR-167KNB (Continental) or its equivalent in the makes mentioned in Appendix 'B'.

Stop valves, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed to 15 mm bore steel tube fixed in repairs complete all as specified.

Brass CP wall mixer quarter turn for mixing of hot and cold water screwed down for iron pipe and fixed in repairs complete all as specified. Make : Cera Cat No. F2002401 or its equivalent in the makes mentioned in Appendix 'B'.

Brass chromium plated shower rose 125mm size fixed in repairs to 15 mm bore steel tube complete all as specified.

Aluminium anodised tubular towel rail, 20 mm dia., D type, 60 cm long between flanges fixed in repairs complete all as specified.

Sheet glass shelf assembly complete all as specified. Make : Cera Cat No. F5001114 or its equivalent in the makes mentioned in Appendix 'B'.

Soap dish, brass chromium plated fixed with screws complete all as specified. Make : cera, Cat No. F5006106 or its equivalent in the makes mentioned in Appendix 'B'.

110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified.

75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified.

75 mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified.

Taking up or down steel tubing 15 mm bore, and connections, including cleaning for re-fixing or removal to store complete all as specified.

15 mm bore, steel water tubing, medium grade, galvanized, with all fitting and fixed complete to walls and ceiling or laid into floor complete all as specified.

Fixing only 15 mm steel water tubing galvanised, any grade, to walls and ceilings or laying in floors complete all as specified. Note : Steel water tubing obtained from taking down shall be used.

Taking up or down steel tubing 20 mm bore, and connections, including cleaning for re-fixing or removal to store complete all as specified.

20 mm bore, steel water tubing, medium grade, galvanized, with all fitting and fixed complete to walls and ceiling or laid in floor complete all as specified.

1000 Ltrs capacity, rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layered, hoisted and fixed in repair in position all as specified including ball brass valves, high pressure with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed to 20 mm bore steel tube complete all as specified.

Taking down old unserviceable aluminium /copper point wiring (light , fan , socket, or power ) complete including fittings and fixtures such as switches , ceiling rose ,pendents , regulators , sockets , light fitting etc and making good disturbed surfaces of walls, floors etc complete all as specified.

Taking down unserviceable main switches , DB's /change over switch along with teak wood boards etc and making good the disturbed surfaces of wall /floors to match the existing surfaces complete all as specified.

Point wiring with 1.5 Sqmm multistranded,1100 volt grade copper conductor FRLS grade PVC insulated, cable and unsheathed type alongwith 1.5 Sqmm PVC insulated stranded copper conductor cable FRLS grade for continous earthing drawn through and including PVC casing & caping with accessories having ISI mark fixed on wall surfaces / ceiling including provision of PVC box of appropriate size for fixing switches sockets etc. complete all as specified for the following:-

One light/fan/bell point controlled by one switch

One socket oulet 5 Amps on same board

One socket oulet 5 Amps on independent board

All as per item No 81 here in before but for socket outlet 15 Amps on independent board with cable of size 4 sqmm and earth continuity conductor cable of size 4 sqmm.

Switch piano flush type single pole one way 5/6 Amps complete all as specified.

Socket outlet 5 pin 5/6 amps flush type multipurpose complete all as specified.

Switch piano 15 Amp 230 Volt, flush button single pole one way complete all as specified.

Socket outlet 2 in 1, 3 pin 5/6 Amps and 3 pin 15/16 Amps flush type complete all as specified.

Bell push flush type single pole one way 5/6 Amps complete all as specified.

Bell ding dong AC 230 Volts, single pole complete all as specified.

Ceiling rose surface bakelite 3 terminals fixed on and including PVC block complete all as specified.

Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings/angle fittings complete all as specified.

LED LAMP 9 W system lumen (NOM) 850 with cool day light CCT 6500K retrofit with base B-22 complete all as specified. Make: Polycab cat No-LLP0101055 or its equivalent in the makes mentioned in Appendix 'B'.

Surface & wall mounted self ballasted LED batten 4 feet with extruded thermoplastic body with PC diffuser in unique square shape greater than 120 degree wide distribution 20 W system CCT 6500K with all accessories complete all as specified. Make: Polycab Product code LDO0103031 or its equivalent in the makes mentioned in Appendix 'B'.

Recess mounted 2 feet x 2 feet edgelit LED slim panel white powder coated extruded aluminium body with high quality LGP and PMMA diffuser, separate HPF driver CCT 6000 K 40 W system luminaire with all accessories complete all as sspecified. Make: Polycab product code . PMD0401018 or its equivalent in the makes mentioned in Appendix 'B'.

Surface mounted LED Bulkhead luminaire 10 W with ABS body & polycarbonate diffuser CCT 6000 K IP 54 complete all as specified. Make : Polycab product code PID0102001 or its equivalent in the makes mentioned in Appendix 'B'.

Decorative wall mounting fitting 8 Watt housing made of stainless steel sheet, stainless steel brush finish, glass diffuser cup shaped optics, opal finish for soothing light effect fixed to the housing by stainless steel clamp using check nut, glass filled engineering plastic E-14 lamp holder with electrical grade copper contacts suitable for 8 Watt lamp TU retrofit CFLcomplete all as specified. Make : Havells Cat No. LHJE01106499 or its equivalent in the makes mentioned in Appendix 'B'.

Exhaust fan 250 mm size single phase 230 Volt 900 RPM with louvers including making hole in wall and making good the disturbed surface of wall to match with the adjoining complete all as specified. Make : havells model FHVVEDXOWH10 or its equivalent in the makes mentioned in Appendix 'B'.

Metal body exhaust fan 450 mm size with single phase 230 Volt 1400 RPM with louvers including making hole in wall and making good the disturbed surface of wall to match with the adjoining complete all as specified. Make : havells model Turboforce or its equivalent in the makes mentioned in Appendix 'B'.

Sub main wiring (surface) with two single core 6 Sqmm FRLS PVC insulated unsheathed stranded copper conductor cable & one single core 4 sq mm FRLS PVC insulated unsheathed stranded copper conductor earth cable connected to common earth dolly drawn through and including PVC casing capping of suitable size with accessories, complete all as specified. Note : Two runs of 6 sq mm cable, one run of 4 sq mm cable and one run of PVC casing and capping shall be measured as one unit.

XLPE insulated IS 7098 (Part-I)-1988 marked, screened, PVC sheathed, armoured electric power cable (heavy duty) with aluminium conductor for working voltage upto and including 1100 volts, cross sectional area of cable 25 sq mm 4 core laid in trenches/fixed on pole/wall/passed through pipe including testing and commissioning complete all as specified.

Sheet metal enclosure vertical TPN DB, 415 Volt 4 way double door suitable for fixing of MCCB 4 pole as incomer and outgoing MCB SP/SPN and suitable size bus bar for each phase with neutral link and earthing bar complete all as specified.

MCCB 100 Amp 415 Volt 16 KA adjustable type thermal or magnetic 4 pole complete all as specified.

Sheet metal enclosure powder coated SPN DB, 240 volt, 8 way double door with copper earth bar and neutral link complete all as specified.

MCB SPN 40 Amps 240 volts 'B' series including making connection complete all as specified.

MCB SP 6-32 Amps 240 volts ' B' series including making connection complete all as specified

New generation energy saving LED flood light powder coated PDC aluminium body wuth toughened glass visor efficacy > 100 Lm/w, 5700K, IP 66, 60 watt capacity including three core flexible wire connection from junction box to light fitting complete all as specified. Make : Product code PAR0206006 or its equivalent in the makes mentioned in Appendix 'B'.

Energy saving LED street light with PDC aluminium body and toughened glass visor fitted in frame secondary optical lens for superior light distrubution effficacy > 100 Lm/w, 5700 K IP66, 45 watt capacity with and provn of PVC Cable 1.5 Sqmm 3 core approx 1.5 mtr long from fitting to ceiling rose, including suitable bracket made of 40 mm bore medium grade GI pipe,1200 mm long, fixing accessories such as mild steel flat iron clamps, nut, bolt ,washers etc complete all as specified. Make: - Polycab product code PUB0505011 or its equivalent in the makes mentioned in Appendix 'B'.

Earthing with galvanised mild steel earth plate of size 600x600cmx6mm thick, buried directly in ground earth (in vertical) earth pit not less than 2.25 meters deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanized iron or earth lead wire 4mm dia (8SWG) by means of nut , bolt, check nuts and washer of galvanized iron including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinforcement with suitable handle made of 8mm round bar , including necessary excavation and earth work in any type of soil , 20mm dia galvanized steel tube for watering with one end fixed with cast iron funnel and wire mesh, 15mm dia bore light grade galvanized steel tubing up to 7.5 mtr for drawing earth wire protection, common salt, charcoal etc complete all as shown in electrical plate No-3 of MES Schedule part-I and testing on completion complete all as specified.

Galvanised corrugated mild steel sheeting 0.63 mm thick with two corrugation side lap fixed with L-type or J-type or cranked hook bolts in roofs etc with grade of zinc coating 275 fixed in repair complete all as specified

Water heater storage type (Geyser) 25 Ltr capacity 5 star rating with multifunctional safety valve, electric operated 230 V, single phase including one no of heating element, thermostat and indicator lamps, including hot and cold water pipe ,NRV ,grouting nut, bolts in walls and making good disturbed surfaces to match with the adjoining surface fixed in repair complete all as specified. Make : Havells Cat No. GHWAPFTIV025 or its equivalent in the makes mentioned in Appendix 'B'. Note :- Old geyser shall be deposited to MES store yard

PRITPAL SINGH

M/S J.S.ENTERPRISES