Special repair work on the Mohammad Ali Jauhar University to Ekta Chowk flyover road in Rampur district. 2nd Call

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. DSR -13.91 Including all T&P, Labour, Material, Royalty Tax but excluding GST

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete DSR no. 13.80 Including all T&P, Labour, Material, Royalty Tax but excluding GST

Painting (one or more coats) on rain water, soil, waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour on old work : DSR - 13.96.1 Including all T&P, Labour, Material, Royalty Tax but excluding GST

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : DSR - 13.99.1 Including all T&P, Labour, Material, Royalty Tax but excluding GST

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 kg per sqm on the prepared bituminous surface cleaned with mechanical broom as per MoRTH specification clause No. 503 complete in all respects. Including all T&P, Labour, Material, Royalty Tax but excluding GST

Providing and laying bituminous concrete Grade-2 with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder VG-30 @ 5.4 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects Including all T&P, Labour, Material, Royalty Tax but excluding GST

Supply and Fixing of moulded shank cats eyes moulded shank raised pavement marker made of polycarbonate moulded body and reflected panels with micro parismatic lens capable of providing total internal reflection of the light entering the lens face conforming to ASTMD 4280 type H and complaying to specification of categories a of MORTH CIRCULAR NO RW/NH/33023/10-97 DO III DT 11-06-1997. The height width and length shall not exceed 20 mm 150 mm & with minimum reflective area of 13 sqcm. and the each side, slope to the base shall be 35 degree. Fixing will be without nails but using twin polymer shanks using bitumen adhesive on bitumen road as per manufacturs recommnendation including site clearance etc and complete as per direction by rengineer in charge. Rates are included all tax & GST. (Sollar Studs or yellow cats eyes to way AND Red & white two way cats eyes) (All complete as per E/I) Including all T&P, Labour, Material, Royalty Tax but excluding GST

Centre/Edge Lines :- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes. (All complete as per E/I) Including all T&P, Labour, Material, Royalty Tax but excluding GST

Dismantling of Flexible Pavements (Dismantling of flexible pavements and disposal of dismantled materials up to a lead of 1000 metres, stacking serviceable and unserviceable materials separately) Bituminous courses By Manual Means Including all T&P, Labour, Material, Royalty Tax but excluding GST

Providing and laying 25 mm thick mastic asphalt wearing course with paving grade bitumen meeting the required given in table 500-39, prepared by using mastic cooker and laid to required level and slope after cleaning the surface, including providing antiskid surface with bitumen pre-coated fine grained hard stone chipping of 13.2 mm nominal size at the rate of 0.005 cum per 10 sqm and at an approximate spacing of 10 cm center to center in both direction, pressed into surface when the temperature of surfaces in not less than 1000c, protruding 1 mm to 4mm over mastic surface, all coplete as per clause 516. Including all T&P, Labour, Material, Royalty Tax but excluding GST

Providing and Fixing of Flexible Median Markers as per IRC 79-2019 which shall be made of combination of tough, high impact resistant molded thermoplastic body along with florescent yellow color retro-reflective type XI sheeting with minimum exposed reflective area 285 square mm and with rebound property. The reflective sheeting should confirm to Type XI Florescent Yellow sheeting as per IRC 67 2012 and ASTM D4956-11. The flexible median marker shall have overall height of minimum 180 mm, body thickness of minimum 2mm and shank depth of minimum 30mm. The retro-reflective sheeting shall be on both sides of the Flexible Median Marker and shall be edge protected with no exposed edges which will prevent edge lifting, vandalism, sheeting damage, etc. The edge of sheeting should not come out easily by putting nails, sharp objects etc. The logo of the manufacturer shall be embossed on either side of the body. The product design has to with stand all natural impacts and should not get damaged if any pedestrian stamp on top of it intentionally or unintentionally. The product should bend up to 90 degree on both sides without breakage or damage. The product shall be tested for reboundability & tensile test as per IRC 79-2019 and government lab test report shall be submitted along with tender. If somehow tender pre qualification condition do not ask for government report then the report shall be submitted to engineer-in-charge before finalization of bill. The rate shall include all materials, labour, equipments, fabrication, transportation, erection, installation and incidentals all complete as per direction of the Engineer-in-Charge. Including all T&P, Labour, Material, Royalty Tax but excluding GST

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 mad of high intensity grade sheeting vide clause 801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-15 grade cment conc. 45 cm x 45 cm x 60 cm, 60 cm below ground lvel as per approved drawing (TRAFFIC SIGNS - (All complete as per E/I) Including all T&P, Labour, Material, Royalty Tax but excluding GST

T- Junction/ X-Junction Sign Board

Speed Limit Sign Board

Hazard Sign in Front

Double side CHEVRON Sign Board

Direction Board on Minor Road at intersection of size 90 cm hight octagonal

Please Enable Macros to View BoQ information