AS AND AS TO WATCH TOWERS UNDER LBW, SPL REPAIRS TO BLDG NO. P 07 (HANGER 7) IN TP AREA UNDER SPECIAL REPAIRS B/R, SPL REPAIRS TO KOQ 16 PINA HOUSE IN PHASE I UNDER SPECIAL REPAIRS B/R AT NAVAL STATION BHEEMUNIPATNAM UNDER GE (P) NAVY KALINGA

Amount

Demolition of cement concrete (unreinforced) in ground floor and pavings n.exc 15cm below or above ground level including removal of demolished materials from work site .

Taking down cement plaster of any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc built in cement mortar .

Taking down door chowkats or frames with shutter area n. exc 1.5 Sqm each (without taking off shutters from the frame) and removing to store .

Taking down chowkats or frame with shutter, (without taking off shutter from the frame) exc 1.5 Sqm but n.exc 4sqm each and removing from site .

Dismantling floors, hearth or wall tilling including cement mortar bedding (but not backing), removing rubbish off the premises .

Demolition of reinforced cement concrete in roof, floors (other than ground level), beams, stair case, landing, chajjas, drops, facia and similar suspended work (reinforcement cut as required to facilitate demolition) .

Hacking out old broken glass any thickness size quality or description from /wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads .

M&L for providing cement concrete type B-1,1:2:4 (using 20mm graded stone aggregate) as cast in situ in lintels upto 1.5m span, cills and other similar bands, plinth courses, string courses, lacing courses, parapets, railings upto 60 cm height, copings, coping, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating .

M&L for 40 mm thick cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in floors finished even and smooth with using extra cement .

M&L for glass dividing strips 3 mm thick & 38mm wide inserted in position conforming to design .

M&L for 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in floors finished with using spike roller for making impression of expanded metal while the concrete is green .

M&L for Non skid/ joint free ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 (Ist quality) as in floor set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 15mm thick screed bed in CM 1:4 finished even and rough .

M&L for glazed ceramic coloured tiles 350 x 250 x 7 mm/ 450 x 350 x 7mm thick (Ist quality) as in vertical surface such as skirting/dado set in neat cement slurry and pointed in coloured cement to match the surface, including 10mm thick rendering to receive tiles in CM (1:3) finished even and rough .

M&L for brickwork with fly ash bricks, straight or curved on plan exc. 6m mean radius, built in cement mortar 1:4 .

M&L for rendering 10mm thick on fair surfaces of brick wall or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement .

S&F for 2nd class hard wood (well seasoned) plain, solid, straight, chowkats and frame, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints .

S&F for 35mm thick 2nd class hard wood factory made plain framed, panelled shutter (any number of panel) with panels of timber flat on both sides (feather edge) or of veneered particle board medium density with commercial veneering on both faces and size of rail and stile as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated .

M&L for 30mm thick II nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (with sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) .

S&F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails, mild steel frame covered with heat moulded wood grain printed PVC sheet (used instead of Plain colour PVC sheet) with 5mm thickx15mm wide PVC sheet beading used inside stiles & rails and decorative PVC beading of 10mmx10mm used instead of exposed portion of PVC sheet beading, panelling of wood grain printed PVC sheet to fit in the mild frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing .

S&F for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet, reinforced with mild steel square tube in opening as per specification & drawing .

S&F for powder coated aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc, (minimum thickness of powder coating shall be 50 micron) .

S&F for anodised powder coated aluminium window and ventilator shutters, sliding type without sash bars, aluminium sections including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws and suitable anodised aluminium handles and rollers complete all as specified (minimum thickness of powder coating shall be 50 micron) .

S&F for 4mm thick plain sheet glass, ordinary quality & glazing with oil putty in square n exc. 0.5 sqm in each pane .

All as per Sch A item No. 23 here-in-before but area exc 0.5 Sqm .

S&F for aluminium XPM wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples .

S&F in repair aluminium XPM wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples .

S&F for 125mm size MS butt hinges medium weight cold rolled fixed to frame .

M&L for 200 mm long , aluminium alloy barrel tower bolts anodised extruded section ISI marked .

S&F for 150mm size aluminium handles, cast type, anodised .

S&F for 300mm long aluminium anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy .

M&L for repair to beam/ chajja/ drop/ facia (broken/ damaged), making good with PCC 1:1.5:3 type B1 or cement mortar 1:3, rendering 15 mm thick with using water proofing compound, sides and soffits in cement mortar 1:4 including necessary form work wherever damaged including re-inforcement duly welded if required, including demolition of broken / loose PCC for taking down old plaster upto 8/ 10 mtr height . Note : Reinforcement will be measured and paid separately.

M&L for Reinforced Cement Concrete type A-1, 1:1.5:3 (20mm graded stone agg) as in fins, facia, chajjas, louvers, drops, parapets and railing exc 60 cm height .

Use and waste of form work to fins, facia, chajjas, louvers, drops, parapets and railing exc and finishing the surface fair .

M&L for TMT bars 6 to 8mm dia cut to length, bent to shape required including cracking bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia .

S&F for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 .

M&L for preparing new painted surfaces by washing, rubbing down and stopping of painted surfaces and applying two coats of cement base paint on surfaces of walls .

M&L for preparing old painted surfaces by washing, rubbing down and stopping of painted surfaces and applying a coat of cement base paint on surfaces of walls .

M&L for preparing new plastered surfaces of walls by brooming down or by steel wire brushing and applying two coats of colour wash .

M&L for preparing old surfaces of walls by brooming down or by steel wire brushing and applying one coat of colour wash .

M&L for preparing old surfaces of ceiling by brooming down or by steel wire brushing and applying one coat of white wash .

M&L for preparation of new wooden surface of any description not otherwise described and exc 10cm width or girth applying two coats of synthetic enamel paint first grade quality over a coat of pink primer .

M&L for 75mm thick PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in plinth protection/ sub base and paving finished cement concrete surfaces even and fair without using extra cement .

Supply only Liquid water proofing compound (ISI marked) of approved make.

S&F for 15 mm dia bib tap fancy type, cast copper alloy chromium plated, with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule .

S&F for vitreous china, water closet pedestal pattern (white) 'P' trap (including fixing bolt, low level flushing cistern of 10 ltr capacity and seat cover) .

S&F for wash hand basin vitreous China white coloured flat back of size (6300x450) mm including a pair of bracket and cutting for pinning in ends of brackets but excluding taps, waste, chain and plug .

S&F for PVC connection 15mm size with PTMT nuts of length 450mm .

S&F for 15mm dia pillar tap cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts. Screwed for iron pipe complete all as specified and as directed.

Dismantling of asbestos cement/ plain or corrugated steel sheets any gauge, thickness, including nainital or similar pattern as in roof covering .

S&F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws .

S&F for pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws .

Dismantling of wall and ceiling boards any thickness including cover fillets, including removing of dismantled material from work site .

Dismantling old decayed timber scantling in fillets, rafters, purlins etc under 40 sq cm section .

S&F for 6 mm thick Asbestos cement plain building boards, fixed to timber framework with screws .

S&F for Asbestos cement building board cover strips, 50mm x 5mm, with bevelled edges over joints including all mitres, etc., and fixed with screws .

S&F for 2nd class soft wood plain fillets square, rectangular or triangular in section, sectional area exc 13 sq cm but n exc 25 sq cm clean sawn, secured with nails or brads .

Taking down existing roof treatment including plaster etc .

M&L for normal water proofing treatment on roof slab portion consisting with the following operation : (i) Cleaning surface by wire brushes broom, removing dust and applying with bitumen primer conforming to IS 3384-1986 @ 0.50 kg per sqm (ii) Applying a tack coat of bitumen 85/25 @ 1.2 kg per sqm for water proofing membrane (iii) Applying of polymeric water proofing membrane weight not less than 3 kg per sqm over entire area with overlapping and sealed complete all as specified and as directed. (iv) Again applying hot bitumen 85/25 @ 1.2 kg per sqm over water proofing membrane (v) Applying a bituminous aluminium primer/ paint 0.10 kg per sqm .

M&L for providing cement concrete type B-1,1:2:4 (using 20mm graded stone aggregate) as roof kerbs, mud stops, rounded or chamfered on edges .

M&L for 100 mm thick cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in floors finished with using spike roller for making impression of expanded metal while the concrete is green .

Dismantling of Brick work or stone boulders masonry built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles .

M&L for brickwork with fly ash bricks, straight or curved on plan exc. 6m mean radius, built in cement mortar 1:6 .

M&L for rendering 15 mm thick on internal surfaces of other than fair faces of brick work in cement mortar 1:6 finished even and smooth without using extra cement .

M&L for rendering in two coats with first coat of 10mm thick in CM 1:6 and second coat of 5mm thick duly mixing water proofing compound in CM 1:4 on fair faces of brick work or concrete surfaces finished fair and even without using extra cement . Note: Supply only WPC shall be measured and paid separately.

Dismantling wrought iron or mild steel work of any description not otherwise provided for fencing etc. and removing unserviceable materials from site of work .

S&F for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to grade Fe-290W (Gde E-165) .

Fabrication, erection and fixing only roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc .

M&L for post construction anti termite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia. holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed by the Engineer-in-Charge.

M&L for treating the soil under plinth protection @ 5 ltrs of emulsion per Sqm of surface area .

M&L for post construction anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron .

M&L for preparation of new plastered surfaces of walls and applying two coat of plastic emulsion over a coat of primer on internal surfaces of wall .

M&L for complete removal of existing treatment of walls and applying two coat of plastic emulsion over a coat of primer on internal surfaces of walls .

M&L for preparation of old wooden surface of any description not otherwise described and exc 10cm width or girth applying one coat of synthetic enamel paint first grade quality .

M&L for preparation of new asbestos surface of any description not otherwise described and exc 10cm width or girth applying two coats of synthetic enamel paint first grade quality over a coat of pink primer on ceiling.

M&L for applying one coat of aluminium paint including preparation of old steel surfaces over 10 cm width or girth, .

M&L for applying one coat of synthetic enamel paint including preparation of old steel surfaces over 10 cm width or girth, .

M&L for preparation of old plastered surfaces of ceiling and applying one coat of plastic emulsion paint .

M&L for preparation of old plastered surfaces of ceiling and applying one coat of cement based paint .

M&L for grouting of column, beam and any RCC surface etc with cement slurry by mixing 50 kg of cement with 18 to 22 litre of water with admixture of FOSROC CEBEX 100 (Plasticized expanding grout admixture) about 225 gms per 50 kg of cement by drilling upto 12 mm dia hole in the surface @ 300 mm C/C upto 60 mm depth and grouting / pumping the grout with mechanically powered grout mixer upto 10 kg for each hole as per manufacturer ‘s instructions and sealing the hole after grouting (GROUT = WATER + CEMENT + FOSROC CEBEX 100 in proportion) complete all as specified and as directed by the Engineer-in-Charge.

M&L for insulation with 50 mm thick glass wool of density 16 Kg/ Cum for insulation laying and properly fixing over false ceiling .

M&L for 2 mm thick (approx thickness) stainless steel 304 grade plain sheet as in valley gutter including fixing of stainless steel collar for drainage .

M&L for 100mm thick PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in sub base .

S&F for machine pressed precast concrete interlocking paver blocks of approved shape and size confirming to IS 15658-2006 of 80mm thickness and M-40 grade, with grey cement and pigments .

S&F for machine pressed precast concrete interlocking paver blocks of approved shape and size confirming to IS 15658-2006 of 60mm thickness and M-35 grade, with grey cement and pigments .

M&L for sand filling under floor or in foundations including watering and consolidation .

M&L for 25 mm thick cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in sub base of floors .

Excavating soft/ loose soil in post holes (or similar holes) each n.exc 0.5 Cu.m getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm watering and removing surplus soil to a distance in n.exc 50m and making good surface .

M&L for Plain cement concrete (1:2:4) type B-2 using 40mm graded stone aggregate as in foundation filling and mass concrete, bed etc complete all as specified and as directed.

S&F for mild steel angle iron/ flat iron work as in hold fast, support of valley gutter and nosing, post, fencing posts, fillets for securing chain link fencing etc including all necessary drilling, bolting or riveting etc., and similar work conforming to Fe-290 Gde E-165 .

S&F for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 including gusset plate, including erection of vertical supports for holding purlins, rafters, base plates, nuts & bolts etc. .

M&L for mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410 W (Gde-E-250) quality A .

S&F for 12 mm dia mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed the both ends each screwed ends to be fitted with washer and one hexagonal or square nuts n.exc 5 cm long .

M&L for 1st or premium or standard quality non skid ceramic coloured joint free tiles of size 600 x 600 x 6 to 7 mm thick in floor, shelves etc set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 15mm thick screed bed in CM 1:6 finished even and rough .

M&L for 1st or premium or standard quality non skid ceramic coloured joint free tiles of size 600 x 600 x 6 to 7 mm thick in skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 10 mm thick screed bed in CM 1:3 finished even and rough .

M&L for preparation of new steel surfaces of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer .

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer on internal surfaces of walls .

M&L for preparation of new external surfaces of walls and applying two coats of cement based paint over a coat of primer on external surfaces of walls .

S&F for 4.8 mm thick sheet glass, ordinary quality & glazing with oil putty in square exc. 0.5 sqm in each pane complete all as specified .

M&L for 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (with sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) .

S&F for anodised aluminium snap grid frame work of size 605 mm x 605 mm for false ceiling .

M&L for providing and fixing gypsum board 12mm thick in ceiling fixed with screw as per manufacturers instructions .

M&L for preparation of new surfaces of ceiling and applying two coats of oil bound distemper .

S&F for stainless steel, curtain rod, 25 mm dia including stainless steel bracket for door and window opening .

S&F for fancy type CP knob round for fixing curtain rod .

M&L for point wiring for One light/ fan point controlled by one, 5 Amp one way switch with 1.5 Sqmm (nominal cross-sectional area) FRLS PVC insulated and unsheathed 1100 V grade multi stranded copper conductor single core cable drawn through and including 20 mm PVC conduit with all fittings and accessories including one run of FRLS PVC insulated and unsheathed single core multi stranded copper conductor cable of size 1.5 Sqmm as earth continuity conductor to common earth and earth dolly .

Supply and fixing LED bulk head fittings 9/ 10 W, 230 V, 50 HZ including LED light driver holder connecting up with three core flexible copper conductor of suitable size upto ceiling rose . Make : Havells Cat Part No. HEXAFT10WLED857SSYMBOPC or equivalent as approved by GE

S&F for switch piano flush button single pole one way 5 amps .

S&F for ceiling rose surface bakelite 65 x 30 mm three terminals .

S&F for wall mounted Air circulators fans PVC body 400 mm sweep 230 volts SP complete with accessories .

Taking down carefully existing aluminium /copper conductor point wiring (light / fan / socket or power point) complete, with all fittings such as switches, socket, regulator, ceiling rose, utility light fittings and lamp holders etc and removing materials from site and making good the disturbed surfaces of walls roof and floor etc as per existing specification .

Taking down carefully by unscrewing from boards / outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and fan regulators etc. for reuse at site . (Note : To be measured only when found serviceable in all respects complete for reuse)

M&L for surface point wiring complete with 1.5 Sqmm PVC insulated unsheathed FRLSH cable multi stranded copper conductor 1100 volt grade flameproof conforming to IS drawn through and including suitable dia stove enamelled ERW MS conduit ISI marked and conduit accessories fixed in surface of wall/ ceiling/ floors etc for flameproof application connected upto light fittings/ fan with 1.5 mm dia copper earth wire for earth continuity conductor and connection to common earth dolly and to be terminated for flame proof application etc including testing on completion .

M&L for concealed point wiring for One light point controlled by one, one way switch with 1.5 Sqmm (nominal cross-sectional area) FRLS PVC insulated and unsheathed 1100 V grade multi stranded copper conductor single core cable drawn through and including 20 mm PVC conduit with all fittings and accessories including one run of FRLS PVC insulated and unsheathed single core multi stranded copper conductor cable of size 1.5 Sqmm as earth continuity conductor to common earth and earth dolly including new pressed steel sunken boxes readily available (having thickness not less than 1.22 mm for boxes upto a size of 200 mm x 300 mm and beyond that the wall thickness shall not be less than 1.63 mm) concealed type with 2 mm thick bakelite sheet cover for mounting switches, sockets, fan regulator etc including testing .

All as per Srl Item No. 113 here-in-before but for One switch socket outlet point 3 pin 5 A on independent board .

All as per Srl Item No. 113 here-in-before but for one switch socket out let for 15 Amps 3 pin on independent board with 2.5 Sqmm cable and 2.5 Sqmm earth wire .

M&L for surface point wiring complete with 4.0 Sqmm PVC insulated unsheathed FRLSH cable multi stranded copper conductor 1100 volt grade flameproof conforming to IS drawn through and including suitable dia stove enamelled ERW MS conduit ISI marked and conduit accessories fixed in surface of wall/ ceiling/ floors etc for flameproof application connected upto power switch sockets with 1.5 mm dia copper earth wire for earth continuity conductor and connection to common earth dolly for one 3 pin power socket controlled by one 16 Amp one way switch .

M&L for flame proof switch socket & plug combined in LM6 cable termination box in LM6 16 Amp 250volt 2P+ earth .

M&L for surface sub main wiring complete with 2.5 Sqmm PVC insulated unsheathed FRLSH cable multi stranded copper conductor 1100 volt grade flameproof conforming to IS drawn through and including suitable dia stove enamelled ERW MS conduit ISI marked and conduit accessories fixed in surface of wall/ ceiling/ floors etc for flameproof application connected upto light fittings/ fan with 2.5 mm dia copper earth wire for earth continuity conductor and connection to common earth dolly and to be terminated for flame proof application etc including taking down old unserviceable sub main wiring. (Note : Copper conductor 2 run of 2.5 Sqm + 1 run of 2.5 Sqmm earth wire and one run of MS conduit shall be measured as one unit)

S&F for flame proof/ weather proof well glass LED light fitting including tube suitable for 1 x 45 watt LED as per IS 13947 body made out of aluminium alloy LM-6 epoxy painted with guard, reflector, flameproof clear glass along with all accessories prewired CMRI certified and hardware in high tensile with corrosive epoxy grey shade paint fixed to wall/ ceiling including flameproof flexible wire from fitting to terminal point . (Crompton Cat Part No. FWL1315-40-CDL or equivalent as approved by GE)

S&F for flame proof junction boxes LM-6 2/3/4 way suitable for 20 mm dia ERW steel conduit complete certified by CIMFR for Gas group I, IIA & IIB for zone I & II . (Sudhir Cat Part No. JB/OA/104 or equivalent as approved by GE)

S&F for flame proof rotary switch with separate cable terminal box including rubber gasket as per IS 2149, SP 25 Amps, 2 pole, 250 volt ISI marked for ON/ OFF light, made out of aluminium alloy LM-6 marked in high tensile steel with anti corrosive epoxy paint grey shade CMRI certified with cable entries .

S&F for flame proof rotary switch socket and plug combined with separate cable terminal box including rubber gasket as per IS 2149, SP 25 Amps, 2 pole, 250 volt ISI marked for ON/ OFF light, made out of aluminium alloy LM-6 marked in high tensile steel with anti corrosive epoxy paint grey shade CMRI certified with cable entries .

S&F for sheet metal enclosure for MCB, DBs, phosphatised, Powder coated , single pole and neutral (SPN) 240 Volt , double door, suitable for 8 way with din rail earth and neutral bar .

S&F for triple pole and earth enclosure with a three pin and earth plug with socket complete with one triple pole MCB .

S&F for MCB Single Pole (SP) C curve 10kA breaking capacity of 6 to 32 amps, 240 Volts in proper position .

S&F for flame proof/ weather proof enclosure for MCB DB including gas cut ring endless Neoprene rubber gasket box size 500 mm x 500 mm x 145 mm with main incomer 63 Amp 4 pole ON OFF Slazer switch- 1 Nos (Door), Door switch 6 Amp SP ON OFF -12 Nos (Slazer Make)- Door, 63 Amp 4 Pole ON OFF MCB Hager make – 01 No (Body), 6 Amp 1 pole ON OFF MCB Hager Make -12 Nos (Body) with wiring and connector .

S&F for flameproof weather proof multi cable entry junction box including gasket kit IP 66 as per IS 2147/1962 ISI marked made out of cast aluminium alloy LM-6, epoxy painted CMRI certified 63 Amp old unserviceable AC flame proof-weather proof enclosure for MCB DB/186 of internal dimension 400 x 400 x 250 mm including taking out old unserviceable junction box .

S&F for air termination vertical type single pointing aluminium rod 12mm dia. and 300mm long complete all as specified and as directed by the Engineer-in-Charge.

S&F aluminium strip 25x3.15mm including insulating blocks, saddle and fixing screws etc fixing arrangement for all earthing connection by each other .

S&F for test point terminal box made out of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 Nos. 8mm dia. 25m long hexagonal head screw complete all as specified and as directed by the Engineer-in-Charge.

M&L for earthing complete with 7.5m CI pipe 80 mm dia with flanged ends, centrifugally cast, class A, in any length, joints with stainless steel nuts and bolts and sufficient slot upto 2.5 mtr length buried directly and preferably vertically in ground with top flanged ended 2.5 mtr below ground level welded/ connected with GI strip 32 x 6 mm size on the top edge of the flange to bottom edge of the flanged for earthing including filling the pit with charcoal common salt surrounding the earth pipe including drilling 400 mm dia bore any strata of soil to lower the CI pipe complete including necessary excavation and earth work PCC (1:3:6) type C-1 with 50 mm thick precast RCC (1:2:4) type B-1 cover slab and necessary testing on completion complete all as specified and as directed.

S&F for LED tube light 18 W, 230 V, 50 HZ including LED light driver holder connecting up with three core flexible copper conductor of suitable size upto ceiling rose .

Supply, Install, Testing and Commissioning of 'Solar Hot Water System' (Flat Plate Collector) based on indirect transfer of heat of capacity 100 LPD .

S&F for Hot water pipe duly insulated with glass wool and aluminium cladding 20 mm bore .

S&F for ceiling fan 1200mm sweep with blades and accessories, BEE 6 star rated with min. air delivery 210 CFM at low voltages, five star rated with brushless direct current motor including fixing of electronic regulator, down rod of 19mm dia 300mm long and connecting up with flexible 3 core 1.5sq.mm twisted copper cable from terminal point to ceiling fan complete all as specified and as directed by the Engineer-in-Charge.

M&L for taking down fan, sealing cable end, dismantling blades and removing fan and blades to store .

M&L for painting of ceiling fans complete of any sweep/make with one coat of first quality synthetic enamel paint of approved tint by spray including preparation of old painted surface and removing all dust, oil mark etc and filling cavities with filler materials .

Hanging only ceiling fan (MD supply) and connecting up including provn of cable from ceiling rose to fan .

Note : All items in the Schedule to be completed all as specified and as directed by the Engr-in-charge.

SRI GOWRI ENGINEERING WORKS

SRI RAJA RAJESWARI ENTERPRISES

ARKA CONSTRUCTIONS

S A R CONSTRUCTIONS

LAKSHMI SAI CONSTRUCTIONS

SWATHI CONSTRUCTIONS

N V S S K N SIVA PRASAD