WBPWD/SE/SWEC/NIQ47/2025-26

Supply and Fixing of 7 mtr. Galvanized Octagonal Pole on the existing base plate (fixed by Civil Wing) with Top A/F 70, bottom A/F 155, Thickness 3 mm, Wind speed shall be considered 50m/s as per IS:875 including Supply & fixing of “J” Type foundation bolts as per EN-B Grade manufactured from special steel along with nuts, washers, Anchor Plate, of required size and templates A) Material Construction Shaft Equivalent to BSEN 10025 Or As per IS 2062 B) Materials grade of Base Plate shall be E250(BR)as per IS:2062 C) Galvanization as per IS 4759 [Make :- Surya/Transrail/Valmont]

Supply, Installation, Testing & Commisioning of 120W solar All in one(Integrated) LED streetlight system, Solar PV panel: Mono Crystalline PV Panel 200WP (Any MNRE Approved) , Solar Battery- 12.8V 100AH Lithum Ferrous Phosphate Battery with BMS BIS approved high lumen efficasy >160 lm/w , Housing - Aluminum, Charge controller- MPPT Intergral charge controller (Inbuild in to the street light) CCT-6000-6500K, IP65, Impact Resistance(IK): IK08(Except for solar panel), Dimming facility available. [Make- SURYA/Phillips /Crompton] A minimum 5-year on-site warranty shall be provided by the Original Equipment Manufacturer (OEM). Warranty documents must be submitted to the Engineer-in-Charge (EIC) prior to installation. N.B. The solar lighting company must have an in-house NABL-accredited laboratory. The successful bidder must submit LM79 and LM80 test reports for the luminaire and LED, respectively, from a NABL-accredited third-party laboratory. The following valid type test reports shall be submitted along with the bid: i) Luminaire Safety: IEC 60598-1:2014 & IEC 60598-1:2014 AMD1:2017 ii) MPPT Performance: EN 50530 iii) Battery Safety (LiFePO₄, IP68): IEC 62133, UL 1642, UN 38.3 iv) Solar Panel Safety: IEC 61730-1, IEC 61730-2, IEC 61215

Earthing with 80 mm dia GI pipe (TATA-Medium)x 3.0 Mts. long and 1 x 19/8 stranded GI (Hot Dip) wire (4 Mts. long), 25 mm dia x 150 mm long galvanized bolt, double nuts, double washers including socketing at both ends of stranded GI (Hot Dip) wire by crimping sockets/ thimbles and S & F 40 mm dia GI pipe (ISI-Medium) protection (3 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level to an average depth of 3.65 Mts

Extra for providing masonery enclosure on the top of the earth electrode of overall size 86.36 cm x 86.36 cm x 46 cm deep (below Ground level) complete with cemented brick work(1:6) of 25 cm width duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 cm x 35.56 cm with locking arrangement, GI reducer including drilling of 46 nos. 12 mm dia holes on the GI pipe

Supply & fixing GI (Hot Dip) strips 20 mm x 3 mm thick for horizontal run on the Parapet/Roof/ Wall with GI Saddles 1100 mm apart incl. mending good the damages to building works

Supply and laying 4 SWG G.I. wire for continuous Earthing as per G.S.

Terms & Conditions:

The agency must procure the material from the manufacturer/OEM or from their authorised sales channel so that the standard warranty/support of the manufacturer/OEM becomes applicable to the product and to be delivered and installed by them.

Documents that authenticate such procurement from the manufacturer/OEM or from their authorised sales channel so that the standard warranty/support should be send from the E-Mail of the manufacturer/OEM or from their authorised sales channel to the email of EIC. and hard copy of it to be submitted during execution of work/submission of bill.

If any refurbished material is supplied and installed, penal action will be taken as per existing rule

Please Enable Macros to View BoQ information