Loading
Loading…
Loading…
Tender Value
₹86.9 L
EMD Value
₹1.7 L
Closing Date
30 Dec 2025, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
MAINTAINCE
15 conditions · 4 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V = Advertised value of the tender in crores of Rupees N = Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The firm/contractor should submit a valid "B" grade or above electrical Contractor license issued by the Government Electrical Licensing Board in favor of the Firm/contractor (OR) the site Supervisor should possess the necessary valid "B" grade or above electrical Contractor license issued by Government Electrical Licensing. A copy of the valid license shall be submitted with the offer. The offer without a copy of a valid "B" grade or above Electrical Contractors license shall be summarily rejected.
Similar Nature of Work: "Works of wiring / cabling or installation and Commissioning of electrical Items (Other than on coaches) such as lights, fans, pumps, charging arrangements, earthing etc (with or without supply of items / equipment's) For 230V, 1 Phase or 415V, 3 Phase System or higher voltages."
47 conditions · 7 needing a document upload
The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society /Registered Trust / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. and corresponding documents shall be submitted by the tenderer as per the composition of the Firm.
The Bid Security shall be deposited either in cash through e- payment gateway or submitted as Bank Guarantee bond from a scheduled commercial bank of India or as mentioned in tender documents. The Bank Guarantee bond shall be as per Annexure- VIA of GCC and shall be valid for a period of 90 days beyond the bid validity period. Non submission of scanned copy of Bank Guarantee with the bid on e-tendering portal (IREPS) and/or non submission of original Bank Guarantee within the specified period shall lead to summary rejection of bid. The original Bank Guarantee should be delivered in person to the official nominated as indicated in the tender document within 5 working days of deadline of submission of bids.
Eligibility criteria :- Eligibility criteria shall be mandatorily incumbent upon the tenderer to identify, state and submit the supporting documents duly self attested/digitally signed by which they/he is qualifying the Qualifying Criteria mentioned in the Tender Document. Non submission of supporting documents for eligibility criteria lead to summarily rejection of the bid.
Tender Form (First sheet, Second sheet) of The GCC April 2022.
Certificate format (Affadivit) which available as Annexure - V in Mandatory documents. A facility has already created for online submission of Annexure V of GCC in IREPS module, uploading of physically signed Annexure V by tenderer has been discontinued.
The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society /Registered Trust / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc.
The corresponding documents shall be submitted by the tenderer as per the composition of the Firm: Sole Proprietorship Firm: (i) All documents in terms of Para 10 of the Tender Form (Second Sheet) above. HUF: (i) A copy of a notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF. (ii) All other documents in terms of Para 10 of the Tender Form (Second Sheet) above. Partnership Firm: (i) All documents as mentioned in para18 of the Tender Form (Second Sheet). Company registered under Companies Act2013: (i) The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company (ii) A copy of Certificate of Incorporation (iii) A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company. (iv) All other documents in terms Para 10 of the Tender Form (Second Sheet) above. LLP (Limited Liability Partnership): (i) A copy of LLP Agreement (ii) A copy of Certificate of Incorporation (iii) A copy of Power of Attorney/Authorization issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP. (iv) An undertaking by all partners of the LLP that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP or JV in which they were / are partners/members. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the Standard General Conditions of Contract. (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet). Registered Society & Registered Trust: (i) A copy of Certificate of Registration (ii) A copy of Memorandum of Association of Society/Trust Deed (iii) A copy of Power of Attorney in favour of the individual to sign the tender documents andcreate liability against the Society/Trust. (iv) A copy of Rules & Regulations of the Society (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet) above.
The tenderer shall be required to submit the Bid Security with the tender for the due performance with the stipulation to keep the offer open till such date as per Clause No.5 of PART -1 of The GCC, April 2022.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Guntakal: 1. Proposed Construction of 11 Units Type-IV Staff Quarters - Electrical arrangements., 2. Proposed construction of Staff Quarters Type-V-4 Units for officers- Electrical arrangements.
GTL-EM-56-2025-26~SCR
GTL-EM-56-2025-26
Open
Works - General
6 Months
Anantapur, Andhra Pradesh
₹0
₹1.7 L
30 Dec 2025
8 Dec 2025
16 Dec 2025
121 items across 2 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 56,62,642.77 | ||
| Supply and Running of 25 mm dia, Ivory coloured PVC conduit ( ISI marked) of wall thickness not less than 2 mm along with junction boxes, bends and all accessories etc. as required as per site requirement. Running of conduit, fixing with suitable clamps and nuts in groove / open /shelter | — | — | — | 97,280 | |
| Supply and running of 32 mm dia, Ivory coloured PVC conduit of wall thickness not less than 2 mm with junction boxes, bends and all accessories etc as required as per site requirement. Running of conduit, fixing with suitable clamps and nuts in groove / open /shelter | — | — | — | 41,489 | |
| Cutting of groove in the wall, plastering of surface to the original for concealing of the conduit in the wall (Laying and fixing of conduit will be paid separately) | — | — | — | 50,400 | |
| Supply and laying of 25mm casing and capping of ISI standard with necessary screws (the distance between the screws shall not exceed 0.5 m) including joints bends and all necessary accessories complete. | — | — | — | 6,400 | |
| Provision of concealed wiring with two runs of 1.5 Sq,mm 1100 Volts and one run of flexible copper conductor 1.5 Sq,mm 1100 Volts FRLS PVC insulated wires ISI marked (Phase, neutral and earth)( upto 10 meters lenght) in the PVC conduit pipe with 6A flush modular type switch including 2 way switches where ever required, ceiling rose, bulb holder and modular type plate cover to MS switch control box including all labour charges complete for light points, ceiling fans and exhaust fans points cat walk points and ioh service buidling points etc. accessories. | — | — | — | 2,68,840 | |
| Supply and run of 2 nos, 2.5 sqmm, 1100 V PVC (FRLS) insulated flexible copper conductor wires and one run of 1.5 sqmm PVC (FRLS) insulated flexible copper cable for earthing in existing PVC conduit Pipe conforming to IS 694 (2010) with latest amendements. | — | — | — | 1,53,000 | |
| Supply and run of 2 nos, 4.0 sqmm, 1100 V PVC (FRLS) insulated flexible copper conductor wires and one run of 2.5 sqmm PVC (FRLS) insulated flexible copper cable for earthing in existing PVC conduit pipe conforming to IS 694 (2010) with latest amendements. | — | — | — | 2,15,600 | |
| Supply, running, Connecting of 1 core 4Sqmm FRLS, PVC insulated Copper conductor cable with necessary accessories like cable ties etc. IS 694 (2010) with latest amendements. | — | — | — | 11,400 | |
| Supply, running, Connecting of 1 core 6Sqmm FRLS, PVC insulated Copper conductor cable with necessary accessories like cable ties etc. IS 694 (2010) with latest amendements. | — | — | — | 74,400 | |
| Supply, fixing, connecting and commissioning of 6A 3pin/5pin modular plug socket, with 6A modular control switch on existing control board with wiring. | — | — | — | 50,239.47 | |
| Supply and fixing of 16 Amps 3/5 pin flush type power plug and socket with modular type switch control including all accessories. | — | — | — | 62,001.22 | |
| Supply and fixing of 16 A SP 1 Modular mini MCB 3KA conforming to IS:13947, C"Curve Model No.AA 1 112 of GM make or it's equivalent in Module box including all accessories complete. | — | — | — | 75,400 | |
| Supply and fixing of TV Socket (Coaxial 40-862 MHZ Socket) Glossy White of model no: AA 1 032 of GM make or its equivalent | — | — | — | 9,460 | |
| Supply and fixing of metal flush box-2 module of model no:JM 02 001 of GM FOURFIVE make or its equivalent with 2 module cover plate (With support frame) of model no:PK SB 02 002 - CASABLANCA of GM make or equivalant make comply with IEC 60669-1 with its latest amendments including all accessories complete. | — | — | — | 40,200 | |
| Supply and fixing of metal flush box-4 module of model no:JIM 04 003 of GM FOURFIVE make or its equivalent with 4 module cover plate (With support frame) of model no:PK SB 04 004 - CASABLANCA of GM make or equavalant make comply with IEC 60669-1 with its latest amendments including all accessories complete. | — | — | — | 3,345 | |
| Supply and fixing of metal flush box-6 module of model no:JIM 06 004 of GM FOURFIVE make or its equivalent with 6 module cover plate (With support frame) of model no:PK SB 06 005 - CASABLANCA of GM make or equavalant make comply with IEC 60669-1 with its latest amendments including all accessories complete. | — | — | — | 13,400 | |
| Supply and Fixing of metal flush box-8 module of model no:JIM 08 005/6 of GM FOURFIVE make or its equivalent with 8 module cover plate (With support frame) of model no:PK SB 08 011 - CASABLANCA of GM make or equavalant make comply with IEC 60669-1 with its latest amendments including all accessories complete. | — | — | — | 21,600 | |
| Supply and fixing of metal flush box-12 module of model no:JIM 12 008 of GM FOURFIVE make or its equivalent with 12 module cover plate (With support frame) of model no:PK SB 12 007 - CASABLANCA of GM make or equivalent make comply with IEC 60669-1 with its latest amendments including all accessories complete. | — | — | — | 29,190 | |
| Groove Cutting for Modular Switch Boards (Each=1 Module) | — | — | — | 19,572.8 | |
| Supply and fixing of of Modular Dummy Plate for modular switch boards | — | — | — | 3,984 | |
| Supply and Erection of DESIGNER energy efficient Studio Plus BLDC star electric ceiling fan of Atomberg make or It's equivalent make of 1200mm Sweep. | — | — | — | 3,51,780 | |
| Supply and fixing of 300m Heavy Duty Exhaust fans as per IS:2312:1967 or latest including necessary plastering, Massinory work and clamps nuts bolts etc. | — | — | — | 30,910 | |
| Supply and fixing of BLDC star 200 mm 20W 1600 R P M Exhaust fans including necessary plastering, Massinory work and clamps nuts bolts etc. | — | — | — | 67,914 | |
| Supply and fixing of Angle Holder similar to model no. of AHLHXAW000 of Havells make or equivalent make with necessary screws and all accessores complete. | — | — | — | 4,653 | |
| Supply and fixing of Jumbo plate for Holder similar to model no. of ASSPGW002 of Havells or equivalent make with necessary screws and all accessores complete. | — | — | — | 1,551 | |
| Supply and fixing of 9W LED bulbs as per attached railway specification. | — | — | — | 10,391.7 | |
| Supply and fixing of wall mounted decorative light equivalent to model no: LHFOAJD1TZ1C060 of havells make or its equivalent with holder. | — | — | — | 1,37,940 | |
| Supply and erection of 40W 4 feet LED tube light, with all connected accessories complete for fixing (The supply includes accessories such as clamps, etc. for fixing) as per attached railway specification. | — | — | — | 93,500 | |
| Supply fixing connecting and commissioning of 4 way TPN DB - 7 segment Distribution board of model no.5078 80 with IP 30 - IK08 of Legrand make or its equivalent, with all connecting accessories complete. | — | — | — | 1,60,128 | |
| Supply, fixing, testing and commissioning of RCBO 63A, Four pole, 30mA as per in accordance with IS 12640-2(2008) or latest with all necessary accessories complete as advised by the site supervisor. | — | — | — | 63,571.2 | |
| Supply and fixing of SPN DB's,8 way 8 module confirming to IEC:61439 IP 43 with metal door model no.507611 of legrand make or its equivalent make | — | — | — | 4,312 | |
| Supply and fixing of C curve FP MCBs of 32 A with all connected accessories. | — | — | — | 4,364 | |
| Supply and Erection of B curve 40A SP MCBs of Rated Short-Circuit Breaking Capacity 10kA of IP 20 Protection as per IS/IEC 60898 - 1 with its latest amendments including all connected accessories. | — | — | — | 11,232 | |
| Supply and Erection of B curve 10/16/20/32A SP MCBs of Rated Short-Circuit Breaking Capacity 10kA of IP 20 Protection ISI / CE Marked as per IS/IEC 60898 - 1 with its latest amendments, with all connected accessories. | — | — | — | 29,440 | |
| Fabrication and erection of 14 SWG CRCA sheet steel enclosure of suitable size for Indoor LT distribution panel with IP 44 with Double Door, including cutting, bending drilling, welding and reveting etc, complete with cleaning with 7 tank process and painting with EPOXY powder coating including cost and conveyance of all materials and labour charges. The MDBs shall be mounted on suitable required size of CC plinth (CC plinth cost will be paid separately) and secured with bolts, nuts and washers as advised by Engineer at site. The panel comprising of 500A Copper Bus Bar of Electrolytic grade copper and duly insulated by heat shrinkable PVC sleeves of R, Y, B and Black Colour complying to IS: 613 with its latest amendments, with appropriate DMC / SMC barriers and colour coded with heat shrinkable sleeves indication lamps for incoming & outgoing feeders. Suppot insulators, neutral links,Incoming & outgoing terminals, suitable cable termination glands, grommets, lugs, connecting wires and all other accessories suit with the following switchgear and accessories. The individual cabinet with suitable amount of space must be provided to fixing of 3 phase energy meters for each outgoing along with MCBs with viewing glass . The cables should be properly terminated in the switchgears with necessary lugs and all necessary accessories complete. Proper labeling and markings are essential for identifying each circuit within the distribution board. The electrical separation will be governed as per IS/IEC 61439 with its latest amendments. The panel should comprise of the following Switchgear : 1. Supply and installation of 250 A 4P MCCB, 36 KA, Micro processor based adjustable with LSIG protection communcation capable conform to IEC 60947- 2 with its latest amendments, model no. 4205 39 of Legrand make or it's equivalent with extended ROM , spreader links (2 sets)- 1 Nos as incoming., 2. Supply and fixing of C curve FP MCBs of 40/50/63 A with all connected accessories- 12 Nos as outgoing in meter cabinets., 3. Supply and instllation of DPX3 160 thermal magnetic based release; Icu = 36kA; 63A 4 Pole MCCB conform to IEC 60947-2 with its latest amendments of model no. 4200 93 of Legrand make or it's equivalent with extended ROM, spreader links (2 sets) - 2 nos as outgoings., 4. Supply and erection of LT 3 Phase Digital Multifunction energy meter with 3 lines LCD display for measuring all the parameters (Voltage/ Current/ Power/Frequency/power factor /kw/kwh/ kvar/kvarh) on existing box panel board including connections complete - 1 Nos., 5. Supply and erection of LED indicator lamps on the panel board - 1 set of 3 nos lights., 6. Supply and erection of LT current transformer with primary 100/5A to 1000/5A ratio in the existing panel including connections complete - 4 no's. The fabricator of Panel should have the approval of CPRI. (Drawing approval to be taken prior to supply. | — | — | — | 1,81,507 | |
| Supply, Laying, Testing and Termination of 4 core 95 sqmm XLPE insulated underground armoured aluminium cable with heat resistant insulation as per IS 7098(Part 1)1988 with latest amendments with necassary lugs and terminations complete. | — | — | — | 5,15,240 | |
| Supply and Erection of HDPE pipe of 63 mm of PE-80 grade in PN-4 size as per IS 4984-2016 with latest amendments and with suitable couplings and clamps for cable laying with all necessary accessories complete. | — | — | — | 1,10,000 | |
| Supply and Laying of 4 core 10 sq.mm copper cables XLPE insulated, cores laid up, PVC inner sheathed unarmoured 650/1100V grade as per IS 7098 (Part 1) 1988 with its latest amendments. | — | — | — | 2,95,036 | |
| Supply and laying of GI earth continuity wire of 6 SWG for providing earth inter connections to the cables etc. as per is 280-2006 or latest | — | — | — | 14,400 | |
| Excavation of cable trench in all types soil of size of size 400mm wide x 1 mtr. deep, and making good of the same to its original form and shape after complete including all connected materials and works up to the satisfaction of the Engineer at Site.The exact route of the HT/LT cable is to be decided in consultation with Engineer in charge. | — | — | — | 60,168 | |
| Excavation of cable trench duly breaking the existing cement concrete flooring and filling with layer of sand bricks etc.,as per the standards of cable laying (A minimum of 1mtr depth and 400 mm width) and filling the trench with soil duly ramming etc.The flooring shall be made good with cement concrete as original by the contractor after completion of trenching work up to the satisfaction of the Engineer at Site.The exact route of the HT/LT cable is to be decided in consultation with Engineer in charge. | — | — | — | 71,680 | |
| Supply, Transportation and fixing of storage / Pressure type Vertical / Horizontal 230/250V Single phase 2000 watts ISI mark 5 Star rated water heater with SS tank/Glass lined and ABS plastic body of 25 Ltrs capacity to withstand up to 6.5 bar of water pressure conforming to IS:2082/93 with its latest amendments including all standard accessories and dead weight pressure reducing valve on out let side, including cost of 2 Nos nylon / PVC / Metallic hose pipe, testing and all labour charges etc. complete. | — | — | — | 3,96,000 | |
| Supply, fixing and connecting of 2pole 2 module 16A/25A Lexic RCBOs conforming to IS 12640-2(2008) with its latest amendments as advised by the site supervisor with all necessary accessories complete. | — | — | — | 33,978 | |
| Supply, Transportaion, Erection & commissioning of 5mtr long hot dip galvanised Octagonal pole (IS 875) with 130mm bottom A/F & 70mm top A/F made up of 3mm thick HT sheet (S 355 JO steel plate for shaft), along with base plate IS 2062 of size 200x200x12mm, M16x600 long J type EN8 grade foundation bolts, 1000mm long single/ Double arm bracket Including the Supply of Suitable bolts with Bakelite Sheet with MCB ( for mounting inside the base compartment of pole ) including Erection & commissioning of 5 mtr. octagonal pole including RCC concrete foundation & plinth in hard soil including excavation of soil, tamping of concrete, grounting and supply of other required materials and accessories complete. | — | — | — | 3,67,472 | |
| Service connection to the fitting from the junction box of 5 mtrs Octogonal pole by means of PVC insulated copper conductor of 3 core 1.5 Sq mm with necessary lugs at the juction box and necessary termination at the luminaire complete. | — | — | — | 7,300 | |
| Supply, Laying, Testing and Termination of 1.1 KV Grade 4 core 16 sqmm XLPE insulated PVC sheathed Aluminium armoured cable as per IS 7098(Part 1)1988 with latest amendments and with necassary lugs and terminations complete. | — | — | — | 85,488 | |
| Supply and Erection of HDPE pipe of 40 mm of PE 63 grade, PN8 as per IS 4984-2016 with latest amendments and with suitable couplings and clamps for cable laying with all necessary accessories complete. | — | — | — | 57,000 | |
| Supply and fixing of LED street light fittings of 48 W with suitable driver with all connected materials as per attached railway specification. | — | — | — | 70,500 | |
| Supply and Erection of LED Flood light fittings of 100 W conforming to IS:16101 ,IEC 60598-1 with its latest amendments, with High quality diffuser IS:10322 with its latest amendments, driver with 380 V high voltage surge protection with all connected materials as per atached Railway specification. | — | — | — | 48,200 | |
| Excavation of earth for one pit in any soil and refilling as per Drg.NO. RE/33/P702/ MOD.F | — | — | — | 4,939.95 | |
| Supply and erection of "B' class GI pipe dia 50mm, 3.1 mtrs length with 3.65 mm thickness including GI socket and nuts (3.1 mtrs ) including drilling of 12mm holes as per the RDSO Drg No. ETI/OHE/P/ 7021 (MOD.A) or if any latest. | — | — | — | 25,314.9 | |
| Drilling of 26 Nos of 12 mm dia holes on GIpipe dia 50 mm | — | — | — | 2,422.5 | |
| Supply and erection of Charcoal | — | — | — | 7,546.5 | |
| Supply and erection of Salt | — | — | — | 5,218.5 | |
| Supply and erection of pre fabricated RCC ofsize 0.55m X 0.55M(550mm) with wall thickness of0.125m(125mm) with height 0.3m (300mm) alongwith RCC(1:4:8) cover with .04m thickness(40mm)and funnel with ire mesh.(as per the Drg No.SC/E/SK-18/2004). | — | — | — | 13,047.9 | |
| Transportation charges including loading &unloading of earthing arrangements systemmaterial to site / location | — | — | — | 3,728.25 | |
| Supply, erection , testing and commissioning of Solar Standalone Street Light system(Model-III) including LED street Light= 36W, within-built Solar chargecontroller,1 No SPV Panel=150Wp, 1 No GEL Battery =75 Ah(2 days Backup), GI Tubular Pole 6M with MPPT(Maximum power point Tracker)(2 Days Backup) with necessary arrangement forfoundation as per specification attached. | — | — | — | 5,12,336 | |
| Couping of exsting rail/tubular pole including required material and labour charges etc. The Couping Should be 600mm height in that, 150 mm below the ground level and 450 mm above the ground level. It includes digging around the Tubular Pole/Rail pole etc to a depth of 150 mm and the diameter of the couping should be 300 mm | — | — | — | 2,500 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .