CA NO.CWE BLY/GE (E)/22 OF 2025- 2026SPECIAL REPAIRS TO OR MD ACCN BLDG NO P-32 (01 TO 08) OR MD ACCN UNDER GE (EAST) BAREILLY

Amount

Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer - in - Charge.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as spcecified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons Laid, bedded and pointed in any mortar etc. complete all as spcecified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove complete all as spcecified and directed.

Demolition of Concrete is ground floors andy pavings n exc 15 cm thickness (below or above ground level)complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

Demolition of concrete of any description and in any position not otherwise specifically provided for complete all as spcecified and directed.

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) removing from site complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) removing from site complete all as specified and directed by Engineer-in-Charge.

Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each and removing from site complete all as specified and directed by Engineer-in-Charge.

Taking down shutter and refixing with easing in same opening of any description exc. 1 sqm but n.exc 2 sqm each

Dismantling of 100mm bore cast iron/ pvc drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed.

Taking down eaves gutters and rainwater pipes 75 mm dia , including all fittings, heads, shoes, bends, swan-necks, etc.,including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fitting and accessories) complete all as spcecified and directed.

Taking up or down15 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge

Taking up or down20 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge

Dismantling water tanks 500 & n exc 1000 and removing to store of all retrieved material ) complete all as spcecified and directed.

M&L 15mm thick rendering in cement mortar 1:4 to brick masonry wall surfaces or on other than fair faces of brick wall surfaces finished fair & even without using extra cement for fixing tiles etc complete all as specified and directed

M & L 25 mm thick PCC 1:2:4 type B0, using 12.5mm graded aggregate as in floors to receive surface of tile complete all as specified and directed.

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed.

M&L screed bed or bedding layer of mortar, 20 mm thick, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed.

M&L Non- skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M&L for non skid ceramic tiles 9 to 10 mm thick (square / rectangular )area of each tiles exc 0.18 sqm but not exceeding 0.38 Sqm in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match with coloured tiles complete all as specified and directed

M&L for non skid ceramic tiles 9 to 10 mm thick (square / rectangular )area of each tiles exc 0.18 sqm but not exceeding 0.38 Sqm on vertical surfaces etc set and jointed in neat cement slurry and pointed in coloured cement to match with coloured tiles complete all as specified and directed.

M & L 9 to 10 mm thick glazed coloured ceramic tiles ( square/ rectangular) with border , area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M&L Machine cut pre- polished kota stone slab flooring 20-22 mm thick and size exc 0.16 sqm jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and treating the surface incl complete complete all as specified and directed

M&L for 20-25 mm thick Machine cut pre- polished kota stone slab as in riser and steps, skirting in full length in single peice without joint, with groove cutting in double line of stair width laid over cement screed and jointed with rubbing and treating the surface incl bull nosing complete all as specified and directed.

M&L 18-20 mm thick granite of black colour (tablee rubbed and polished) as in windows cill , in steps, jambs, pillars, cooking platforms and like in cement mortar (1:4) including form work , pointing in white cment (1:2) using marble dust with admixture of pigment to match with shade of granite with full round bull nosing edging complete all as spcecified and directed.

M & L for 75mm thick PCC 1:3:6 , type C-2 using 40 mm graded stone aggregate as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed .

M& L 100 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base floor / pavings complete all as specified and directed

M&L Sand filling under floors or in foundation including watering and consolidation complete all as spcecified and directed.

M&L for cement Concrete coloured interlocking paver blocks shall be factory made with casting in rubber/pvc moulds & compacting on a vibro table assembly and shall be cured in curing tank for atleast 14 days and then air dried before use. The paver block shall be confirming to IS 15658 -2006 of 60mm thickness, M-35 Grade. Approved design, shape, size and colour of top layer complete all as specified and directed.

M&L for precast machine pressesd glazed rubber moulded PCC (1:2:4) type B0 using 12.5 mm graded aggregrate, including weathering, slightly rounded or chemferred angles and throating , as directed edges joint filling with in CM 1:4 complete including excavavtion for kerb stone as directed.

M&L for reinforced cement concrete 1:1.5:3 type A-1 (using 20mm graded stone aggregate) (nominal mix) as in slabs supported on wall,landing, balconies, shelves and like including bonding agent , complete all as spcecified and directed. (reinforcement to be measured & paid under respective items).

M&L form work to chajja, weather shade, troughs and similar items including edges for rough finished surfaces of concrete flat,complete all as spcecified and directed.

M&L form work to edges of concrete flats, treads, breaks in floors window cill, concrete railing opening in conc wall , floor and roof n.exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n.exc 20cm wide for rough finished surfaces of concrete, complete all as specified.

Supply and fix TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) but not less than 0.9 mm dia conforming to Fe-410 - 0, complete all as spcecified and directed.

M&L PCC 1:5:10 type E-2 (40 mm to 80 mm graded stone aggregate) as sunken sub base of floor fillings complete all as spcecified and directed.

S&F 32mm dia GI pipe, medium grade as in spout pipe in sunken floor complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as spcecified and directed.

M&L rendering 15 mm thick in CM 1:6 on brick masonary wall surfaces or on other than fair faces of brick masonry finished even and smooth witout using extra cement complete all as specified and directed.

M&L 15mm thick rendering in cement mortar 1:4 to on brick masonary wall surfaces or on other than fair faces of brick masonary fair finished without using extra cement with using water proofing liquid @ 0.15 Ltr per bag of cement complete all as specified and directed. (Note : Water proofing liquid shall be measured and paid separately)

M&L rendering 10 mm thick in CM 1:4 as on concerete surface on ceilings finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M & L for applying cement slurry over existing roof surface @ 3 Kg/Sqm incl mix with water proofing liquid @ 0.15 ltr per 50 kg cement bags as per manufactures instructions complete all as specified and directed.

M &L for PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregrate laid over roof slab after applying cement slurry for filling undulationations finished even and smooth without using extra cement complete all as spcecified and directed.

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:4, over RCC roof slabs for laying water proofing treatment mixed with using water proofing liquid @ 0.15 Ltr per bag of cement complete all as specified and directed by Engineer-in-Charge. (Note : Water proofing liquid shall be measured and paid separately)

supply Integral water proofing Liquid complete all as spcecified and directed.

S & F in repair 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as spcecified and directed.

S&F for 40 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed .

S&F 35mm thick 2nd class factory Glazed and skeleton shutters, open rebated of saal wood second class hard wood rail and stles and prepared to receive glass, gauze, etc. (without sash bars), divided into squared, with plain, cham-fered or rounded, mitred and rebated sash bars, any numbers sizes of members of shutters as specified in SSR Part I, Section 8. cla-use 8.24 (a); supplied and fitted to chowkats complete all as specified and directed by Engineer-in-Charge. (Note :- S & F Glass/gauge shall be measured and paid for separately)

S & F 150 mm long floor door stopper of aluminium alloy body and tongue, brass body and tongue with hard drawn steel spring. Fixed in floor

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick single side prelam PVC sheet used instead of Plain colour PVC sheet , suppling & fixing in opening as per specification & drawing

S&F 30 mm thick factory made both side Prelam PVC sheet used instead of Plain colour PVC sheet. Stile and rails feathered at edges consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F mild steel window grills box type framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding complete FE-290 grade E-165 all as specified and directed.

S&F Powder coated aluminium sliding windows frame with movable shutter ( sliding on minimum two PVC roller of best quality, for each shutter on three tracks with stainless steel mosquito proofing and glazing shutter and incl 5.00 mm thick glass & stainless steel wire mesh fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below- (i) Window frame :95x38mm X 1.15 mm thick for three tracks. (ii) Top/bottom rail and style / rail of shutter : 15x37.5x1.15 mm thick and over. (iv) stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperature 1.40mm and fixed in aluminium window or alongwith F/Y section fixed with aluminium wire staples complete. (v) Aluminium fittings such aluminium suitable handle with auto interlock cap with suitable size . (vi) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed.

S&F Powder coated aluminium sliding windows and frame with movable shutter ( sliding on minimum two PVC roller of best quality on two tracks Aluminium composite panel shutter fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below- (i) Window frame :45.2x35mm X 1.15 mm thick for two tracks. (ii) Top/bottom rail and style / rail of shutter : 15x37.5x1.15 mm thick and over. (iii) Aluminium beading - 0.7mm thick (v) Aluminium fittings such aluminium suitable handle with auto interlock cap with suitable size . (vi) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed.

S&F Powder coated aluminium ventilators box type with louvers & wire mesh fixed with neoprene rubber gasket, aluminium beading, clips. Frame made with powder coated aluminium section of size as appended below (i) frame :45.2mm x35mm X 1.15 mm (ii) Aluminium beading - 0.7mm thick (iii) Glass louvers depth 6 inch. Blade Angle: 38 degrees and thickness of blade 2.02 mm with 106.25 mm spacing. (iv) Aluminium neccessary fittings complete as required. (v) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed.

S&F Powder coated aluminium box section in cupboard with side hung shutters fixed with & including aluminium composite panel LDPE core PET coating ( both side decorative type ) fixed to shutter frame with powder coated aluminium beading clip & rubber gasket inside of the cupboards , frame made of powder coated aluminium box section & shelf tops & verticle partitions & back side made of alumnium composite panel fixed to frame with powder coated aluminium beading etc.Frame ,shutter, shelves & vertical partition shall be made of size & material as appended below complete all as specified & directed (a) Frame :- Powder coated aluminium box section 100x44x1.48mm thick, fixing with wall face to be done with powder coated aluminium angle cleats & powder coated matching colour S S screws.(b) Shutters:- (i) Middle and lock rail :Powder coated aluminium box section 100x44x1.48mm thick (ii) Bottom rail : Powder coated aluminium box section150x44x1.48mm thick.(iii) Top rail/style :Powder coated aluminium box section 85x44x1.48mm thick. (iv) Aluminium composite panel : 5.0 mm thick both side decorative type.(c) Shelves :- Frame : Powder coated aluminium box section 61.85 x31.75x1.49 mm thick in both horizontal & vertical sides, (ii) Aluminium composite panel : 4.0 mm thick both side decorative.(Note:- Shelf area per sqm of front measerable area shall not be less than 3.10 sqm , design of shelf to be approved by GE). (d) Powder coated aluminium beading : 0.7mm thick (e) Powder coated aluminium handle, tower bolt, (f) stopper , mortise lock 4 leaver( 02 Nos of each cupboard) of approved make.Making good of wall surface to match with existing surface complete.with neccessary fittings all as spd as directed measurable area only front surface area of cupboard shutter . (Note:- Design / colour / pattern of aluminium composite panel & colour of powder coating shall be approve by GE )

S & F 300 mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as spcecified and directed.

S & F 150 mm thick Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as spcecified and directed.

S&F 150mm size aluminium handles, cast type anodised completed all as specified and directed.

S&F 100 mm size butt hinges medium weight stailess steel complete all as specified and directed by Engineer-in-Charge.

S&F 300 mm size ordinary mild steel , rat tailed rod pattern spring including roller and roller plate welded to mild steel frame.fixed in repair complete all as spcecified and directed.

S&F 300 mm long aluminium sliding door bolts plate type with bright bolt not less than 16 mm dia with and including a minimum of 6 bolts and nuts, 04 Nos on bolt plate and 02 Nos on staple plate and fix complete all as specified and directed

S&F 1000 litres, rotational moulded polyethylene of white colour in tripple layer water storage tank (cylindrical vertical with closed top with suitable size of M S Tasla with suitable locking system ), hoisted and fixed in position complete all as specified and directed

S&F 20mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm dia steel water tubing galvanized medium grade concealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge

S&F 20 mm dia steel water tubing, galvanized, medium gradeconcealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed

S&F in repairs vitreous chinaware coloured wash hand basin with pedestal of size 55X45X82cm complete including fancy CP pillar tap, CP Waste coupling ,waste pipe ,complete fixing arrangement and cutting for and pinning in walls & making good complete all as specifed and directed by Eng in charge.

S&F Brass chromium plated wall mixer 2 in 1,15mm for mixing hot & cold water screwd down three joints to steel pipes or unions and plugging and screwed to walls complete all as specified and directed.

S&F fancy type 15mm dia chromium plated fancy type wall mixer hot & cold with long swan for kitchen sink fixing and connection to pipes complete all as spcecified and directed.

S & F in repair fancy type 150mm size square brass CP shower rose complete all as spcecified and directed.

S&F in repairs 15 mm dia bib tap fancy type chromium plated with flange quarter turn complete all as specified as directed.

S&F fancy type chromium plated brass two way bib cock suitable for 15mm bore pipe complete all as specified and directed.

S&F in repair stainless steel of AE - SI 316 grade tubular towel ring including apair of CP brass bracket complete all as spcecified and directed.

S&F in repairs 15mm bore PVC connections, with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair fancy type brass chromium plated soap dish of 160x160x90 mm , complete all as spcecified and directed.

S&F in repair fancy type chromium plated brass angle valve type suitable for 15mm bore pipe complete all as spcecified and directed.

S & F fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP bracket gaurd and railling 60 cm long complete all as spcecified and directed.

S&F in repairs of 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as spcecified and directed.

S&F in repair 15 mm dia fancy type stop cock , chromium plated with long shank and cup (conncelaed type)for iron pipe or for unions and fixed.

S&F in repair vitreous china squatting pan of orrissa pattern long pan size 580 x 440 mm white with "P"or "S" trap size 100 mm dia front or back inlet and integral foot rest any pattern (excluding flushing cistern and flush pipe) including provn of lime concrete bedding complete all as specified.

S&F in repairs, PVC low level cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed .

S & F Brass CP health faucet with 8mm Dia 1.0 Meter Long Flexible Tube and Wall Hook screwecd for iron pipe fancy type long body all as specified and directed.

S&F in repair PVC (SWR) multifloor trap with grating including jointing with solvent cement floor trap 75 mm dia outlet plain with grating including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as specified and directed.

S&F PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fitting complete all as specified and directed by Engr-in-charge.

S&F PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fittingcomplete all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75 mm bore junction single (Single 'T') equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) 110 mm bore junction single (Single 'T') equal or unequal with access door complete all as specified and directed.

S & F PTMT alloy toilet cabinet with mirror of overall size 350 x 450mm and fixed to wall complete all as specified and directed.

S&F in repairs Stainless Steel plate rack of size 90x80x25cm made with 1.00 mm thick sheet including taking out existing wooden plat rack, complete all as specified.

S & F in repair 0.8 mm thick stainless steel kitchen sink size 590x460x230mm undermount, single bowl (bowl size 540x410x230 mm) , incl waste pipe & SS coupling, washers etc. complete all necessary fittings all as specified and as directed .

S&F in repair 20 mm dia stainless steel 1.0 mm thick fancy type droppery rod with decorative design matching brackets as approved and knobs (lattu) or end bracket as required incl fitting with 80 mm long SS screw with 75 mm long wooden gitty of appropriate c/s in each end & intermediate support complete all as specified and as directed

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1979

S&F Pre-coated galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as spcecified and directed.

M & L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, Chajja ( up to IInd floor) etc making good, cutting exc 10cm and not exc 20cm girth in brick walls complete all as specified and as directed.

Dismantling of concrete by chiseling from RCC members like column , beam, parapet facia, chajja, ceiling,etc exposingthe reinforcement without disturbing the reinforcement free from rust by sand blasting/using chemical , apply a coat of rustolin to remove rust and acralic polymer on old rusted reinforcement proving at places addl reinforcement welding with existing reinforcement as directed wherever required binding RCC 50 mmx50 mm (10 mm gauge welded mesh ) & tack , securing with clips / blinding wire, welding & provision guniting pressure 2.2 to 2.5 kg /sqm with admixer 1 cement 3.5 of sand of thickness 25 to 40 mm including stripping floating with wooden strippers for proper dimension control neccssary form work & scaffolding up to three storey and including height of head room complete surface of guniting to be finished fair with 10 mm thick plaster in cement mortar 1:4 with water proofing compound @3% by weight of cement and construction fibre as per manufacturer instruction cleaning & removing of waste meterial etc as dirply two coat of Water proofing liquid at interval of 8 hours cure for the surfaces complete all as spd as directed

S&F for 0.71mm thick Aluminium plain sheeting Alloy 31000 H4, stucco embossed finish with fixed with coach screw and Aluminium washer in roof and wall etc. with end laps stitched with 25x6mm G.I. bolts at 20cm apart gap to be with thermocol sheet incl dismantling also complete all as spcecified and directed.

M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted wooden or wood based surfaces of any description n.exc 10 cm in width or girth when unconnected with other painting or when painted in a diferent tint and applying one coat of synthetic enamel paint over and including one coat of red oxide complete all as specified and directed.

M&L for complete removal of existing treatment on wall by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropirate grit to make surface clean,free from dust ,loose paint etc by skilled labour and applying of two coat OBD on wall with airless electric sprayers over a coat of primer applied using airless electric sprayers over two coats of wall care putty of 1 mm thickness prepared and sanded with electrically operated sanding machine complete all as specified and directed. Application to be done through authorised dealer .

M&L for applying of two coat OBD on newly plastered surface of wall with airless electric sprayers over a coat of primer applied using airless electric sprayers over two coats of wall care putty of 1 mm thickness prepared and sanded with electrically operated sanding machine complete all as specified and directed. Application to be done through authorised dealer .

M&L for preparation of newly plastered walls surfaces and applying two coats of cement base paint over a coat 1mm thick wall care putty complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed.

M&L for complete removal of existing treatment on ceiling, etc including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying two coats of white wash complete all as specified and directed.

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings, tube light fittings etc complete and removing all retrieved materials to MES stores for segregation of serviceable /Unserviceable fitting&fixture and also making good disturbed surfaces of wall, floors etc complete all asspecified and as directed by the Engineer-in-Charge.

M&L concealed point wiring complete with single core FRLS PVC insulated, unsheathed, multi stranded copper conductor cables 1.5 Sqmm 1100 volts grade, with and incl 1.5 Sqmm FRLS PVC insulated, unsheathed, multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, complete wiring drawn through & including PVC Conduit (Concealed in wall/ceiling) of size 20mm dia and above (as per conductor run ) medium grade, ISI marked, incl all accessories & fittings / junction boxes / inspection covers etc, with and incl concealed Modular metal flush box of suitable size flush in wall surface, suitable for fixing of Modular cover plate , switches / sockets etc, complete all as specified and d irected for the following :- Note : 1. Modular white cover plate shall be measured and paid separately 2. Rate quoted shall deemed to be inclusive of cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as spcecified and directed.

All as per item No 112 above, but for one 3 pin socket outlet 5/6 Amp on same board complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 112 above, but for one 3 pin socket outlet 5/6 Amp on independent board complete all as specified and as directed by the Engineer-in-Charge.

One bell/ buzzer point controlled by one push button on the same board with other switches or independent with cables 1.5 sq.mm size complete all as spcecified and directed.

All as per serial item No 112 here-in-before, but for one socket outlet 15/16 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge.

S&F Modular Switch 1 way 16 Amps, 1 Module size complete all as spcecified and directed.

S&F Modular Socket 6 A, 5, Pin 2 Module size complete all as spcecified and directed.

S&F Modular Socket 6A/16 A, 5 Pin ,2 Module size complete all as spcecified and directed.

S&F Modular Switch 1 way 6 Amps, 1 Module size complete all as spcecified and directed.

S&F Modular white cover plate with frame, 1 Module size complete all as directed..

S&F Modular white cover plate with frame, 3 Module size complete all as spcecified and directed.

S&F Modular white cover plate with frame,4 Module size complete all as spcecified and directed.

S&F Modular white cover plate with frame, 6/8 Module size complete all as spcecified and directed.

S&F Modular fan regulator step type complete all as spcecified and directed.

S&F Modular Bell push 6A 1 module complete all as spcecified and directed.

S&F electric call bell ding dong AC 230 volts Single Pole complete all as spcecified and directed.

Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge.

Supply and fixing angular lamp holder, metal cased body of brass with back plate in batten fittings, including Plastic square box of required size complete all as specified and directed by the Engineer-in-Charge

S&F LED Bulb 9 Watt complete all as spcecified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as spcecified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as spcecified and directed.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as spcecified and directed.

S&F in replacement of street light fitting bracket, 1.5 mtr long made out of galvanized iron pipe of 40 mm dia size light grade complete with and incl 02 nos MS clamp made of MS flate iron of 50 x 6 mm size with nut, bolts, washer etc with and incl two coats of aluminum paint over a coat of red oxide primer, complete all as spcecified and directed.

S&F in replacement LED street light luminaire of 35 Watt capacity, made of single piece pressure die-cast aluminium housing with high power LED with lens for proper light distribution luminiaries, IP 66, with toughned glass cover and incl control gear etc, with and incl making all electric connection, complete all as specified and directed by Engineer in charge.

Taking down MCB Distributing board with MCCB/MCB of any size and capacity complete all as specified and directed

Supply and fixing sheet Metal enclosure double shutter type for DB’s 240 Volts Single Pole and Neutral 12 way with 200 Amps rated bus bar complete complete all as specified and as directed by the Engr-in-Charge..

Supply and fixing SPN 40 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning complete all as spcecified and directed.

Supply and fixing SP 5 to 32 amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning complete all as spcecified and directed.

S&F in replacement VTPN DB 6 way double door type including MCCB TP 63 Amps as incomer complete all as specified and directed

Taking down submain wiring of size 4/6 Sqmm complete all as specified and directed

M&L for concealed sub main wiring with 2 run of 6 Sqmm FR, PVC insulated, unsheathed and stranded copper conductor cable with and incl 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn drawn through & PVC conduit of size 20 mm and above incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required,complete all as spcecified and directed. . Note : 1. The cost of concealed conduit & accessories is deemed to be included in quoted rates. 2. The two run of 6 Sqmm wire and one run of 6 Sqmm wire will be measured as one unit.

-ditto- but all as per item Ser No. 142 above but of size 2 Runs of 4 Sqmm

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 5 of SSR 2009 Part-I and connecting to MCBDB’s earth test point all as specified or indicated including testing on completion .complete all as spcecified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc

Taking down the old serviceable electric meter and keeping in safe custody including refixing the same including necessary electric wire, flexible pipe and PVC conduit of suitable size 6 Sqmm from DB to Meter and fixing accessories required as per site requirement complete all as specified and directed by Engr-in-Charge

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as spcecified and directed.

M & L Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store, complete all as spcecified and directed.

S&F in replacement AC functional Box MCB protected Socket plastic base dimension 4 module raise neutral link complete with one single pole MCB 20 Amp 'C' Series 240 VOLT complete all as spcecified and directed.

M/S Rajeev Sharma and Co. (BID ID -3356621)

Shikhar ji Enterprises (BID ID -3356870)

MOHINDER SINGH AND SONS (BID ID -3356715)

TEAM ACC INFRABUILD PRIVATE LIMITED (BID ID -3347575)

Builders Harpal (BID ID -3356693)

NORTH INDIA PEST CONTROL (BID ID -3356930)