SPL REPAIR TO BLDG NO P-30 (RP DUMP STORE) OF CERTAIN MIL UNIT AND SPL REPAIR OF BATHROOM NEAR TRG NODE (NP-01), BATHROOM NEAR TRG CELL (P-50) AND BATHROOM NEAR MT STORE (P-47) OF CERTAIN MIL UNIT UNDER GE (S) BINNAGURI

Material and labour for providing and laying first-quality, fine machine-cut, mirror-polishable Kota stone slab flooring of nominal thickness 20 mm to 25 mm, of approved shade, size, texture, and colour (selected greenish-blue, grey, or brown), conforming to IS 1130 and IS 1443, in floors, landings, corridors, passages, and treads of steps at all heights, elevations, and floor levels, executed in a comprehensive flooring and finishing sequence comprising: thoroughly cleaning, chipping, hacking, washing, and pre-wetting the base concrete / RCC substrate, applying a neat cement slurry bonding coat; laying a 15 mm thick (average thickness) bedding screed bed in cement mortar 1:6 (1 part ordinary Portland cement : 6 parts graded coarse sand / fine aggregate); setting, tapping with wooden mallets, and bedding the pre-wetted Kota stone slabs true to line, level, and specified drainage slope using neat grey cement slurry applied over the screed bed at the rate of not less than 4.40 kg of cement per square metre of floor area, admixed with approved light-fast mineral colour pigment to match the stone shade; jointing with uniform fine hairline/paper joints, filling and pointing joints flush with matching pigment-admixed cement slurry or polymer-modified grout; precision machine edge cutting, straight cutting, and notch cutting around columns, pipes, and corners; continuous water curing for a minimum period of not less than 7 days; followed by systematic multi-stage mechanical machine grinding, rubbing, and polishing using water and carborundum abrasive stones of progressive grit sizes (rough cut with Grit No. 60, intermediate with Grit Nos. 120 and 240, and fine finish with Grit No. 320), washing clean, grouting fine pinholes with matching cement slurry, light grinding, and final mirror-buffing with oxalic acid and tin oxide / approved floor wax to obtain an ultra-smooth, high-gloss, even, non-slippery, scratch-free, and stain-free surface; including washing down, cleaning all slurry splashes and stains from adjacent walls, skirtings, doors, and frames, complete all as specified. (Note:Rates include the 15 mm average thick CM 1:6 screed bed, cement slurry bedding @ 4.40 kg/sq.m with matching pigment, machine cutting, joint pointing, multi-stage machine grinding, rubbing, oxalic acid mirror polishing, and curing. Base RCC floor slabs, sub-grade PCC foundation beds, and vertical Kota stone skirtings, dados, and step risers shall be measured and paid for separately under relevant items of Schedule 'A' unless specified otherwise.

---Ditto-- all as above item No 1.00 in riser of steps, skirting, dado and pillar laid over cement screed 10mm thick (average thickness) in cement motar 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified

M&L for coloured Non skid joint free ceramic tiles (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortar 1:6 complete all as specified

M&L for non skid coloured joint free ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18Sqm but n. exc. 0.38 Sqm, vertical surfaces, in skirting etc. set and jointed in neat cement slurry and pointed in whiter or coloured cement to match as in floor complete including 15mm rendering on fair faces of brickwork or concrete with CM 1:4 all as specified

M&L for cutting out cracks to 'V' section (shape) in existing roof slab terracing cleaning out and filling solidely with cement and sand mortar (1:1) complete all as specified

M & L for Cutting out concrete blocks, slabs, brickwork or stone masonry (in alter nate course), forming tooth-ings for and bonding new work in mortar into old work, including new materials entering old wall in CM 1:4 complete all as specified

Supply only 100% virgin polyester triangular micro-fibres of approved make and brand, engineered specifically as secondary reinforcement for all types of plain and reinforced cement concrete (PCC/RCC), precast elements, floor toppings, guniting/shotcrete, and cement mortars/plaster systems, conforming to ASTM C1116 (Type III: Synthetic Fibre-Reinforced Concrete) and IRC:SP:46, having a unique triangular cross-section for superior mechanical anchoring, cut length of 6 mm (for plaster/mortar) or 12 mm / 18 mm (for concrete), filament diameter/effective thickness of 20 to 40 microns, specific gravity not less than 1.34 to 1.39, melting point not less than 240°C to 260°C, and tensile strength not less than 400 to 600 MPa, supplied in factory-sealed moisture-proof pre-measured pouches / poly-bags (such as 125 g pouches or bulk packs), delivered to departmental store / site of work, ready for direct dispersion during dry or wet mechanical batch mixing to arrest plastic shrinkage/micro-cracking and improve flexural toughness, impact resistance, and water impermeability, complete all as specified. (Note: Makes of Triangular Polyester Fibres: Reliance Industries Ltd. [Recron 3s - 6 mm / 12 mm] / Sika [SikaFiber / Crackstop] / Fosroc [Cebex / Structuro] / STP Ltd. [ShaliFiber 3s] / Master Builders Solutions / Saint-Gobain Weber or approved equivalent as in the list of Makes).

M&L for 5mm thick plaster rendering on fair faces of concrete surfaces as in ceiling in CM(1:3) finished even and smooth (without using extra cement) complete all as specified

Material and labour for preparing internal or external surfaces of cement plaster, concrete, brickwork, or ceiling soffits and applying 2 mm nominal thickness of white cement-based polymer-modified wall care putty in two uniform layers (each coat approximately 1 mm thick), at all heights, elevations, and floor levels, executed in a systematic finishing sequence comprising: thoroughly preparing the substrate by scraping off loose mortar droppings, efflorescence, dirt, dust, and grease using wire brushes, steel scrapers, and sandpaper; washing down and pre-wetting the plastered/concrete substrate with clean potable water to achieve a saturated surface dry (SSD) condition; mixing factory-packed white cement-based polymer putty with clean water using a mechanical stirrer to obtain a lump-free, homogenous, workable paste; applying the first layer (nominal 1 mm thickness) evenly over the surface using a steel trowel / putty blade from bottom to top, filling all surface undulations, pinholes, and hair cracks, allowing it to set and dry for a minimum of 4 to 6 hours; gently rubbing down the dried first coat with fine waterproof emery paper (grit size 180/220) to eliminate blade marks; applying the second finishing layer (nominal 1 mm thickness) in a perpendicular / cross direction to achieve a cumulative minimum thickness of 2 mm; allowing full drying for 24 hours, followed by final rubbing and buffing with extra-fine waterproof emery paper (grit size 320/400) to obtain an ultra-smooth, uniform, even, plumb, non-powdery, and crack-free white surface ready to receive primer and paint; including providing and erecting necessary staging, scaffolding, ladders, drop sheets, masking, and thoroughly cleaning all putty droppings and dust from adjacent floors, joinery, glass panes, and electrical fittings, complete all as specified. (Note: White cement-based wall care putty shall conform to IS 17435 / IS 15477 and manufacturer technical specifications, and white cement base to IS 8042. Rates include all substrate scraping, washing, pre-wetting, mixing, two coats of putty application [each 1 mm thick], double emery sanding, scaffolding at all heights, and cleanup. Base cement plaster rendering, structural crack repair mortar, and subsequent primer / distemper / emulsion paint finishes shall be measured and paid for separately under relevant items of Schedule 'A' unless specified otherwise. Makes of White Cement Based Wall Putty: Birla White [Wall Care Putty] / JK Cement [JK WallMaxX] / Asian Paints [TruCare Wall Putty] / Berger Paints [Bison Wall Putty] / Nerolac [Wall Putty] / Sika / Fosroc or approved equivalent as in the list of Makes).

Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories.(Area not exceeding 2.00 sqm)