Establishment of Mini Secretariat at BARAK VALLEY, Silchar, Assam

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil. (i) 0.0-1.5m

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Disposal of excavated excess earth away from the site including conveyance of materials up to an average lead of 5KM away from the site, and correspondiong required lift, loading, unloading etc complete as directed by the Engineer-in-charge. (The quantity is net quantity of capacity of truck after deduction of 20% for looseness)(considering the maximum disposal location at 5 KM distance) 1.1.2 (8): By mechanical transport including loading, unloading and stacking. (Lead upto 5KM away from the site)

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Supplying chemical emulsion in sealed containers including delivery as specified. 2.34.1: Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete: 2.35.1.1: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : (4.1.5)1:3:6 (1 cement : 3 coarse sand (Zone-III) derived from natural sources : 6 graded stone aggregate 40mm nominal size derived from natural sources).

1:4:8 (1 cement : 4 coarse sand (Zone-III) derived from natural sources : 8 graded stone aggregate 40mm nominal size derived from natural sources).

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size,well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete.

Walls (any thickness) including attached pilasters, butteresses,plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform.

Shelves (Cast in situ)

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts.

Stairs, (excluding landings) except spiral-staircases.

Small lintels not exceeding 1.5m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like.

Edges of slabs and breaks in floors and walls Under 20 cm wide

Weather shade, Chajjas, corbels etc., including edges.

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 5.22A.6: Thermo-Mechanically Treated bars of grade Fe-500D or more.

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Extra for laying reinforced cement concrete in or under foul positions.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/Cum. Excess/less cement used as per design mix is payable/recoverable separately). 5.33.1: All works upto plinth level

All works above plinth level upto floor V level.

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/ cum.Excess/less cement used as per design mix is payable/recoverable separately). 5.37.1: All works upto plinth level

All works above plinth level upto floor V level

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof.

Providing and fixing in position 12mm thick bitumen impregnated fiber board conforming to IS: 1838, including cost of primer, sealing compound Grade-A in expansion joints.

Providing and fixing sheet covering over expansion joints with iron screws as per design. Aluminium fluted strips 3.15 mm thick.150 mm wide.

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.

Filling sunken floor with broken Over burnt (Jhama) brick aggregate 90 mm to 45 mm including compacting and supplying of materials complete as specified and directed for all levels.

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate.

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 11.6.1: 18 mm thick

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles,including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). 11.20.1: Light shade pigment using white cement.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing & Laying vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer) with water absorption's less than 0.08% and confirming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc, complete. 11.41.2: Size of Tile 600x600 mm

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 11.26.1: 25 mm thick.

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 11.56.1: Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

NSI: Providing,fitting and fixing wooden flooring from Uniproducts (India) Ltd.of thickness 14mm made of pure wood(Engineered Wood) of different types with a top layer of 3mm thick hard wood and Under layer of 2mm thickness made of polythene and foamsheet laid on existing concrete floor complete as directed and specified Engineered Wood (New) from Uniproducts(India) Ltd. i) Walnut Brand

NSI: Providing,fitting and fixing Carpet tiles of size 500x500mm with thickness not less than 4mm made of 100% Olefin Polypropleyne material,with dual backing; Primary backing with PVC and Secondary with Reinforced Fibre glass from Uniproducts (India) Ltd.laid on existing concrete floor complete as directed and specified Carpet Tiles from Uniproducts(India) Ltd. i) Ultimate Brand

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).

Providing and Fixing stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 meter height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately)18 mm thick mirror/ eggshell polished granite stone of approved shade

Providing and fixing 18mm thick gang saw cut ( premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels.Granite of any colour and shade.Area of slab over 0.50 sqm .

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc.complete as per design approved by Engineer-in-Charge.Granite work.

Extra for fixing marble / granite stone over and above corresponding basic item, in facia and drops of width upto 150mm with epoxy resin baesd adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/Stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edge etc. complete.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade.

Extra for pre finished nosing to treads of steps of marble / granite stone.

Extra for marble / granite stone flooring in treads of steps and risers using single length up to 2.00 metre.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineerin- Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel dressed on top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints 10mm wide filled with same mortar including ruled pointing etc. complete as per direction of engineer-in-charge.

Providing and fixing dry cladding at all heights with 30 mm thick granite stone of approved shade, fixed to structural steel frame work and / or with the help of stainless steel cramps of required shape and size, pins etc. and sealing the joints with approved weather sealant including grouting the frame work/cramps/pins, maintaining the grooves in stone slabs as per the drawing and filling the same with non-staining, non-streaking silicon joint sealants of approved make, including backer rod, drilling, anchoring, grouting, scaffolding, edge polishing, chamfering to received tapered stone and providing and applying coating on external surface of stone with solvent based silicone sealant of approved make as per manufacturer's specifications etc., all complete as per architectural drawings and direction of Engineer in charge. (Only exposed surface will be measured for payment. The steel frame work, stainless steel cramps and pins shall be paid for separately).30 mm thick mirror/ eggshell polished Granite Stone of approved shade.

Providing and fixing structural steel frame (for dry cladding with 30mm thick gang saw cut with machine cut edges sand stone) on walls at all heights using M.S. square/ rectangular tube in the required pattern as per architectural drawing, including cost of cutting, bending, welding etc. The frame work shall be fixed to the wall with the help of M.S. brackets/ lugs of angle iron/ flats etc. which shall be welded to the frame and embedded in brick wall with cement concrete block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) of size 300x230x300 mm, including cost of necessary centring and shuttering and with approved expansion hold fasteners on CC/RCC surface, including drilling necessary holes. Approved cramps/ pins etc. shall be welded to the frame work to support stone cladding, the steel work will be given a priming coat of Zinc primer as approved by Engineerin-charge and painted with two or more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the Engineer-in-charge for approval before execution). The frame work shall be fixed in true horizontal & vertical lines/planes. (Only structural steel frame work shall be measured for the purpose of payment, stainless steel cramps shall be paid for separately and nothing extra shall be paid).

Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size, adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete as per drawings, specification and direction of the Engineer-in-charge.

NSI: Providing and Fixing Glass fiber Reinforced Concrete (GRC) screen 50 mm thick on border and 35mm thick inside in approved size, pattern, Design and color manufactured by “DALAL TILES/EVEREST/BIRLA/SENEISHA/UNSTONE ” make. The screen should be made with ’53 grade’ white Portland cement manufactured by ‘Birla White/JK’ or equivalent, Alkali Resistant Glass fibers manufactured by ‘Owens corning’ or equivalent, Quartz, fine silica sand, Super plasticizers manufactured by ‘BASF/PERMA’ or Equivalent, U.V. resistant Synthetic inorganic Pigments should be used for pigmentation manufactured by ‘Bayferrox’ or equivalen t, the material casting should take place in Synthetic Rubber / FRP Mould manufactured by Dalal Tiles or equivalent.MS Frame/ Aluminum Frame Work if any to be paid extra as per approved rates.

NSI: Providing and fixing Dalal Tiles make Glass Reinforced concrete (G.R.C) ornamental Formliners casted in approved size, pattern, thickness (20 thickness based on Design) and shade. The Formliners should be made from ’53 Grade’ white Portland cement manufactured by ‘JK Cement’ or ‘Birla white’, white quartz fine graded sieve Silica sand, Alkali Resistant glass fiber by ‘NEG Japan’, owens corning ‘Saint Gobain’ or equivalent, superplasticizer manufactured by ‘SIKA’ or equivalent, polymer manufactured by ‘Nova Polychem’ or equivalent and UV Resistant Synthetic inorganic pigments should be used for pigmentation manufactured by Bayferrox Lanxess or equivalent. The fixing of Formliners should be done using ‘Dry Cladding’ method onto structural support members i.e., RCC, Brick work or Red oxide primer paint or Epoxy prime paint treated mild steel or aluminum Channels. The fixtures, fasteners and self-tapping screws to be used for dry fixing should be of HP/HILTI/CANON/FISCHER. The quantity of fasteners or self-tapping screws shall be calculated in accordance to the weight of Formliners and actual site fixing conditions. If there shall be a requirement of joint filling then Elastomeric exterior grade paintable PU Sealant will be used. For Final finishing of Formliners one weather shield exterior grade water based diluted paint coat will be done if required. Vendor shall submit shop drawings of the same, the drawings to be duly approved by the engineer in charge at site. Framework to be paid extra as per actual.“DALAL TILES/EVEREST/BIRLA/SENEISHA/UNSTONE ” make only shall be provided.

NSI: GRC WORK : Providing & fixing architectural moldings profiles and other decorative elements made out of GRC (Glass Fibre reinforced Cement) in required shape, size & thickness all as per manufacturers specifications, such as all decorative articles should be made by using high power spray machine, using AR Glass fiber with minimum ZrO2 16% including necessary scaffoldings for all heights, as per approved drawings and reference images. GRC elements thickness shall be 12-15 mm. fixing edges will be 4O TO 50 MM GRC Elements shall be fixed on RCC Structure/Brick Work/ Primary Steel Structure (MS with protective coat of Red oxide/Zinc Primer Shall be Used). Hilti make GI Screw Fastners or equvalent, GI Thread Rods and MS cleats shall be used for fixing of GRC elements on RCC/MS Primary fabricated structure. Joints shall be filled with PU sealants/ base material of GRC as and where required. The quote rate shall be inclusive of all design, & shop drawing and sample mock of all elements approval from Architect & consultant. The quote rate shall include all Taxes, duties, statutory obligations and safety code compliance as per client.Rate shall be inclusive of all required fabrication work for fixing only primary strcure shall be provided as base structure only as per requirement. Mode and method of measurement shall be in accordance with IS: 1200.a ) Grc work:as per specification work (Elevation area- At any height) CORNICE FINISH WITH GRC BEND-as per above specification work.(Elevation area)

ii) GRC Corbel -as per above specification work.(Elevation area)

13.16: 6 mm cement plaster of mix : (13.16.1) 1:3 (1 cement: 3 fine sand) Basement Floor

ii) Gr. Floor

iii) 1st. Floor

iv) 2nd. Floor

v) 3rd. Floor

vi) 4th. Floor

vii) 5th. Floor

viii) 6th. Floor

ix) 7th. Floor

13.5: 15 mm cement plaster on rough side of single or half brick wall of mix : (13.5.2) 1:6 (1 cement: 6 coarse sand) Basement Floor

ii) Gr. Floor

iii) 1st. Floor

iv) 2nd. Floor

v) 3rd. Floor

vi) 4th. Floor

vii) 5th. Floor

viii) 6th. Floor

ix) 7th. Floor

13.6: 20 mm cement plaster of mix : (13.6.1) 1:4 (1 cement: 4 coarse sand) Gr. Floor

ii) 1st. Floor

iii) 2nd. Floor

iv) 3rd. Floor

v) 4th. Floor

vi) 5th. Floor

viii) 6th. Floor

ix) 7th. Floor

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. i) 10m to 13m

ii) 13m to 16m

iii) 16m to 19m

iv) 19m to 22m

v) 22m to 25m

vi) 25m to 28m

vii) 28m to Top

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.45.3: 12.5 mm thick tapered edge gypsum moisture resistant board

NSI: Wooden Laminate Partition Work: i) Providing and fixing in position opaque partition consisting of frame work in extruded aluminum sections 1.6 mm th , of approx size 50 x50 mm , placed at center to center at not more than 600 mm both ways , joined using angle 35x35x 3 mm . Securly fixed to wall and , floor and ceiling complete in all respect . The rates shall be inclusive of cutting , punching of holes for drawings conduits and boxes for electrical works etc. ii) Providing and fixing to aluminum frame work , First Skin of 12mm thick Exterior Grade MDF, fixed with fully threaded parallel shank screws at 200 to 300 mm centre to centre , on both sides of framework. Joints staggered on either sides of the partitions to avoid through joints complete as per architectural drawings as per direction of the engineer in charge . iii) There after providing and fixing Second Skin of 6mm thick Exterior grade MDF board on first layer of 12 MM MDF, both side of partition , Fixed with suitable adhesive & fully threaded parallel shank screws at max. 230mm c/c both ways. Joints staggered on either sides of the partitions to avoid through joints. Providing grooves of size 6mm x 6mm complete as per architectural drawings as per direction of the engineer in charge . iv) Providing and fixing infill of 50mm thick & min. 60 kg / m3 density Mineral Wool Insulation. Mineral wool packed in polyweave packets inside partition frame work fixed to wall with Clip, screw, rawel plug & washers and held in position by criss cossing GI wire etc. complete as per directions of Engineer-in-Charge. v) Providing and fixing in 1.0mm thick laminate from sheet of required size & colour over full height /free standing partition / wall paneling / doors fixed with adhesive of approved quality compelte as per directions of Engineer-in-Charge.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.52.3: 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on interlocking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile,rotary stiched double webbed white with 6mm reveal profile (white/black),comprising of main-T runners of size 15x42mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate cross- T of size 15x42 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. 26.23.1: With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles .

Providing and fixing GI Clip-in Metal Ceiling System of 600x600 mm module which includes providing and fixing wall angle ('C' shaped of size 20x30x20 mm made of 0.5 mm thick or 'L shaped of size of min 19 x 19 made of 0.3mm thick ) pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main carrier ( main carrier to be either C shaped of size 10x38x10 mm made of G.I steel 0.7 mm thick or Inverted triangle shaped spring Tee of size 24 mm x 34 mm and made of GI steel of thickness 0.45mm or 15 mm x 37 mm and made of GI steel of thickness 0.5mm ) and width from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm bullet fasteners of size 40 mm long and 10mm dia, 6mm dia GI threaded rod and carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee of size 24 mm x 34 mm and made of GI steel of thickness 0.45mm or 15 mm x 37 mm and made of GI steel of thickness 0.5mm is then fixed to the main carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main carrier and spring T have to join, main carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive). The item includes making required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. and providing and fixing with clip in tiles into spring ‘T’ with 12.54.2: GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation.

NSI: Providing and fixing certified restroom cubicle system of approved make comprising of green guard certified solid compact laminated water proof board, minimum 18 mm thick made as per IS: 2046 (phenolic core board) and as per BS-476/97 for fire retardant for toilet showers, water closet etc . The board shall be manufactured under high pressure and temperature by impregnating kraft papers and outer decorative papers with thermosetting phenolic/ melamine resins (low VOC). The cubicle system shall be resistant towards water, chemical, scratch, impact and heat and shall be anti bacterial, colour fast and shall have accessories like door knob, Gravity/ auto return hinges, privacy thumb turn with occupancy indicator, coat Hook, etc all in SS 304. The hardware and fixings includes anchoring of all fixed front panel to floor with SS 316 L brackets/ base plates with a clearance height upto 110 mm, and covered with SS 316 Shoe box plates, wall and corner joineries (brackets and channels) shall be SS 304 grade, SS 304 screws, rubber noise reduction tape . The cubicle unit shall be installed in approved finish, shades and colours as per specifications and directions of Engineer-In-Charge, including minimum 5 (five) years warranty against any moisture related damages to all intermediate panels, doors, hardqwares etc. Standard dimension of the cubicle system shall be of approx. 2100 mm Height(overall) x 1500mm Depth and 1000 mm Width which includes 600mm door size width. i) I shaped Cubicle System consisting of front face panel including door and all necessary accessories, fittings and hardware etc.

ii) L shaped Cubicle System consisting of front face panel including door, intermediate panel and all necessary accessories, fittings and hardware etc.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 12.21.1: In 75x75mm deep chase.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx400micron, finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : 12.51.1: Ridges plain (500 - 600mm)

Barge board (Upto 300 mm)

Gutter (600 mm over all girth)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). 9.1.2: Sal wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 9.21.1: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : a) 9.40.1 2nd class teak wood 50x12 mm

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive of approved quality 9.127.2: 1mm thick.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 9.96.1: 300mm x 16mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 9.97.3: 200x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Single rubber stopper.

Supplying , fitting, fixing Stainless Steel fittings of approaved make , resonably smooth, free from sharp edges and corners ,flaws and other defects and with counter sunk holes for screws including necessary c.p. brass screws etc. complete.( bright natural matt & satin finished) a) Sliding door bolts i) 300mmx16mm

b)Tower Bolt i)300mmx10mm

c) Door handles ii)100mm

d)butt hinge i)125mmx50mmx2.5mm

NSI: Providing and fixing approved brand and manufacture of Door Closer C680 (Code:-8156), with speed adjustment along with necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge.

NSI: Providing and fixing approved brand and manufacture of REMO Rossette with 240MM Lockbody and 60MM One side Key One Side Knob Cylinder (Code:3903+8447+ 8449) along with necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge.

NSI: Providing and approved brand and manufacture of Single leg Door Stopper (Code:4040) along with necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge.

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474, including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, fasteners screws etc as desired. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural/ curtain wall glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including : a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalization & drainage and protection against fire hazard including: b) Fabricating and supplying serrated M.S. hot dip galvanized / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimensional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon separator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer in-Charge.

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened (as approved) glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner heat strengthened (as approved) clear float glass 6mm thick, spacer tube 12mm wide, desiccants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.1.8.16 above). For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (To be fixed on extruded aluminium sections. and cost of aluminium sections to be paid in relevant item) (i) Coloured tinted float glass 6mm thick Heat Strengthened substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc.

Extra for openable side / top hung vision glass panels (IGUs/laminated glass) including providing and supplying at site all accessories and hardware for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer in- Charge..

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge (Door handle, lock and stopper etc.to be paid separately).

NSI: Providing and fixing Stainless steel 304 Grade H- type pull handle of size min 32 mm dia and 1200mm long of approved make including SS screws, including making holes of required size in shutter etc. complete as per direction of Engineer-in-Charge.

NSI: Providing and fixing SS Bottom patch Lock with cylinder of approved make including necessary screws etc. all complete.

NSI: Providing and fixing SS floor mounted half dome door stopper of dia 45mm including necessary screws etc. all complete.

NSI: Providing and fixing 12mm thk. Toughened float glass glazing cut and fixed in openings of desired shape as per drawing with 3/4" beveling all around, fixed with the help of SS patch fittings, with top and bottom 'C' channels, fixed firmly to the slab/ MS Structure ,as directed by Engineer in Charge. Area of openings to be measured). Assume frameless glass. Rate of above item to include P/F of : 20x20mm "C" channel SS patch Fittings.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed echanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. Glazing and paneling to be paid for separately) :For fixed portion.Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

With float glass panes of 8 mm thickness (weight not less than 20 kg/ sqm)

Filling the gap in between aluminium frame and adjacent RCC/Brickwork/ Stone Work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge Upto 5mm depth and 5mm width

Providing & fixing (shower) cubicles with 10 mm thick toughened glass as per layout of the toilets given in the drawings . The rate includles cost of toughened plate glass fixed glazing fixed with stainless steel connectors floor to glass edge polishing of glass for size of cubicle 2150 and door different size with all accessories like door, privacy thumbturn with occupancy indicator , coat hook, Gravity hinges, Door stopper, door knob, adjustable show box etc, all fixing installation Stainless steel accessories like screws, nuts, bolts, grounting, drilling & towel bar with pull handle 25mm dia 450mm long, 200mm long SS matt finish etc. all complete including installation charges etc all complete.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. The Contractor shall provide curtain wall with aluminium composite panel cladding,and including base frame work for ACP having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately)Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm).

White washing with lime to give an even shade :New work (three or more coats)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

NSI: Providing and laying weather and Ultravoilet Resistant, Water Repellent, Dust, Dirt and Stain Resistant, Fungus and Algae Resistant Ultra Perlato natural texture including one coat of Acrylic Primer and Wall sealer and one coat of protective top etc. complete as per direction of Engineer-in-charge of OIKOS/UNISTONE/ULTRATECH

Applying priming coat: 13.50.1: With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required 10.25.2: In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 10.16.1 : Hot finished welded type tubes

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Supplying and fixing-rolling shuters of approved make.made of required size of M.S.Iaths inter locked together through their intire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arragements for inside and outside locking with push and pull operation complete including the cost of prioviding and fixing necessary 27.5 cm long wire springs grade no. 2 and M.S. top cover of required thickness for rolling shutters. 10.6.1: 80 x 1.25 MS laths with 1.25mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Extra for providing mechanical device chain and crank operation for operating rolling shutter. Exceeding 10.00 Sqm and upto 16.8 Sqm in the area.

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). 10.11.1: Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:Profile B,Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge.10 x 80 mm.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding.

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design :With 20x20 mm square bar.

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality 19.19.1 L D- 2.5 H D - 20.Circular shape 560 mm internal diameter.

NSI: 'Fabrication, supply and Installation of New clear line glass railing system by Ozone made of Heavy duty aluminum U Type Hollow walls Base channel ( HWBC) (OZRF-NCLSYS- HWBC-AL) AL-6063 grade with mill finish of size 12.5mm( thick)72( wide)x122 mm( height). Glass Specs. is 16.89mm thk (8mm CT+ .89SGP+8MM CT) to be GRIPPED with fixing kit (OZRF-NCL-ACC-KIT-17MM) made of self-pushing clamps ( SPC) made by hardened aluminum -6063 grade each at maximum 350mm cc to cc . glass should be lifted from base by Solid Nylon L Block separates at least 3 nos/ meters. HWBC to be fixed with M12 GI stud chemically grouted. Glass should be fixed with completely dry system so that in case of breakage it can be changed without any silicon cutting and very fast as well.. exposed edges of HWBC (if any) to be covered with SS 304 grade end caps. The Top Edge of glass will be covered with SS 304 grade Round slotted tube of Dia42x1.5 mm thk. fixed on the glass edge with EPDM gasket. The Vertical joint of glass will be free from silicon. The total height of the system will be max. 900 mm from ledge top, All top rail joints will be joined by using argon welding only.

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) : 2.4.2: Screened through sieve of I.S. designation 16 mm

Screened through sieve of I.S. designation 4.75 mm

Fine dressing of the ground.

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : 2.14.1: Holes 1.2 m dia and 1.2 m deep

Holes 90 cm dia, and 90 cm deep

Holes 60 cm dia, and 60 cm deep

Holes 45 cm dia, and 45 cm deep.

Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia and 30 mm long bolts, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be suitably fixed to the ground by embedding four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction and direction of Officer-in-charge.

Providing and fixing M. S. tree guard 45 cm square in plan, height 1.20 metre above ground level and 0.40 metre below ground level. The vertical members shall consist of four nos. angle iron of size 25x25x3 mm, 1.6 m long, one at each corner and 8 nos flat iron of size 25x3 mm, 1.2 m long. The vertical members shall be welded to 4 nos. 25x6 mm M. S. flats placed horizontally around the vertical member of the cage. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD/ PWD/ any other approved name. The tree guard shall be fixed to the ground by making suitable holes and by embedding four corners leg in the ground, including refilling the earth, compaction etc. complete. The tree guard shall be painted with two or more coats of synthetic enamel paint of approved brand and manufacture over a coat of primer, complete in all respect.

Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos horizontal & 4 nos vertical “ U “ shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge. 2.29.1: Top inside dia 35 cm, outer bottom dia 25 cm, total height 35 cm with wall thickness of 25.4 mm

Providing Square Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos horizontal & 4 nos vertical “ U “ shape) M.S. wires of 3.5 mm dia as per design, including required frame work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge. 2.30.1: Top inner width 35 cm, outer bottom width 25 cm, total height 35 cm and wall thickness 25.4 mm

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.

Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide will be provided by the Department & lawn mover and brush cutter with fuel , other T & P material/articles shall be provided by the contractor.) 2.40.5: Play grounds / Public parks (as per yard stick 1 Mali =2.00Acre).

Complete maintenance of shrubs (Out side garden features), jobs like making of basin at regular interval i/c watering, weeding, pruning & application of fertilizer etc, (excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge.

Providing & fixing of White River (Stone) Pables size of 2" to 2.50" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge.

Providing and applying anti termite treatment of infected trees i/c all branches/leaves by spraying chemical emulsion 0.5% (Chlorpyriphos 20% EC) concentration through power spray machine (@ 100 ml Chlorpyriphos per tree i/c cost of chemical) and as per direction of officer-in-charge.and as per direction of officer-in-charge.

Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area.(two application) i/c cost of chemical)and as per direction of officer-in-charge.and as per direction of officer-in-charge.

Providing and Displaying plants Budded Rose (H.T. variety) 3 to 4 healthy branch 30 cm and above ht. well developed with one and above flower plant in 20 cm Earthen Pot, as per direction of the officer-in-charge.

Providing and Displaying plants Creeper Rose variety 3 to 4 healthy branch 60 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge.

Providing and Displaying plants Standard Rose (H.T. variety) 3 to 4 healthy branch 90 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge.

Providing and Displaying Acalypha plant Different colour well developed, fresh & healthy with good foliage, multi branch 30 to 45 cm ht. in 20 cm size of Earthen Pot/ Plastic Pot bushy plant as per direction of the officer-in-charge.

Providing and Displaying Acalypha red plant well developed with fresh & healthy 30 to 45 cm ht. in 20 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge.

Providing and Displaying Ficus reginold piller type Topiary plant well developed with fresh & healthy 210 to 240 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy plant in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Ficus Long Island topiary plant well developed with fresh & healthy 5 to 6 ball specific size and shape 120 to 150 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying of Clerodendron inerme plant of ht. 30 cm to 40 cm multi branched in 25 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge.

Providing and Displaying of Iresine herbstii plant, of height 20-30 cm., full of branches well developed in 20 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge..

Providing and Displaying of Wadelia trilobata plant,full of leaves in 15 cm size of Poly bags & as per direction of the officer-in-charge.

Supply and stacking of Alstonia scholaris plant of height 150-165 cm. in bag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Bauhinia blakeana (Kachnar) plant of height 120- 150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Ficus benjamina (green) plant of height 150-165 cm., bushy with healthy branches and lush green foliage in big size HDPE bags as per direction of the officer-in-charge.

Supply and stacking of Ficus religiosa (Peepal) plant of height 150-165 cm. in big poly bags of size 30 cm as per direction of the officer-in-charge.

Supply and stacking of Nauclea cadamba (Kadam) plant of height 150-165 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.v

Supply and stacking of Plumeria acutifolia plant of height 150-165 cm. with 3-4 branches in big size HDPE bag as per direction of the officer-in-charge.

Supply and stacking of Washingtonia filifea palm plant stem ht. 120-135 cm with 8-10 healthy leaves lush green leaves well developed in big size HDPE Bags as per direction of the officer-in-charge.

Supply and stacking of plant Caesalpinia pulcherrima species of height 45-60 cm. in earthen pot of size 20 cm as per direction of the officer-in-charge.

Supply and stacking of plant Calliandra hybrida of height 105-120 cm., well branched, bushy in big size HDPE bag as per direction of the officer-in-charge.

Supply and stacking of plant Hamelia patens of height 30-45 cm. with 3-4 branches in poly bags of size 20 cm as per direction of the officer-in-charge.

Supply and stacking of plant Hibiscus rosasinensis of height 45-60 cm. with 3-4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge.

Supply and stacking of plant Tabernaemontana coronaria (Chandni single) of height 90-105 cm,bushy in big size HDPE bag as per direction of the officer-in-charge.

Supply and stacking of plant Tecoma gaudichaudi of height 90-105 cm.,bushy in big size HDPE bag as per direction of the officer-in-charge.

Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). 20.2.2: 500 mm dia piles

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. 20.6.2: Single pile above 50 tonne and upto 100 tonne Safe capacity Initial test (Test Load 2.5 times the Safe capacity)

Routine test (Test Load 1.5 times the Safe capacity)

Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/ 450N/ 5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :3 mm thick.

Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100% polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin- charge. The product performance shall carry guarantee for 10 years against any leakage. 22.23.1: For vertical surface two coats @0.70 kg per sqm

For horizontal surface one coat @1.10 kg per sqm.

Providing and injecting approved grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete/ masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in- Charge.Epoxy injection grout in concrete/RCC work of approved make

NSI: 15mm thick plastering of the interior surface of concrete water tanks with cement mortar in prop 1:4 admixed with modified Styrene Butadiene Rubber based polymer like Sika Latex of Sika India Ltd./Dr. Sealkit Masterbond Latex (Asian Chemicals)/Rheomix 141 of BASF @ 200gms per bag of cement as specified and directed by the department complete.

Providing and applying crystalline mortar by mixing in the ratio of 4.5 : 1 (4.5 parts crystalline mortar : 1 part water) for the treatment of faulty construction joints, cracks, tie rod holes and spalled & honeycombed surface of RCC underground structures like basement, water tanks, bridge deck etc. to ensure water tightness. The crystallie mortar shall conform to the EN 1504-3 having compressive strength Class R4 > 45 MPa and adhesive bond strength Class R3 > 1.5 MPa. The work shall be carried out all complete as per specification and the direction of the Engineer-In-Charge. The product performance shall carry guarantee for 10 years against any leakage. For sealing cracks and faulty construction joints, routed out/making U-shape groove size 25x25mm and then primed the area with integral crystalline slurry @0.05kg/ running metre and while the surface is tacky filled the groove upto surface with crystalline mortar @1.50kg/ running metre. Once crystalline mortar is touch dry then finally applied two coats of integral crystalline slurry @0.05kg/running meter per coat.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of : (i) Ist course of applying cement slurry @ 4.4 Kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 Kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/sqm.)

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm. depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth lead upto 50 metres.

Supplying and Stacking of Good Earth by mechanical transport including loading, unloading including royalty & carriage up to 5 KM complete.

Spreading of sludge, dump manure and/or good earth in required thickness and extra for compaction of earth work as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineerin- Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).

Painting runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-in-charge, i/c cleaning the surface of all dirt, scales, oil, grease and other foreign material etc. and lining out complete. New work (Two or more coats)

Providing, laying and making kerb channel 30 cm wide and 50 mm thick with cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth etc. complete and as per direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

NSI: Supplying, fitting and fixing SoundSoak NSS Cord (FSS Cord) wrapped acoustical wall panel system of Anutone Acoustics Ltd. Including all fixtures and fittings. Armstrong Wood works acoustical wall panelling

NSI: Providing & fixing Armstrong Mineral fibre Acoustical suspended ceiling system with optra FG ( board/tegular) edge tiles with armstrong XL 24mm exposed grid (600x600x15)mm

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

NDSR-01: Providing and fixing of Health Faucet of approved quality with 1.5m long plastic NBR braided pipe (SS braiding) flexible pipe, wall hooked complete as required. (Make-CERA, Model-F8030202)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. (Handicapped Toilet)

NDSR-02: Providing and fixing of 1 No. U-shaped rail with wall mounting of (Size: 600x100mm) at fixed height for handicap toilet complete as required. (Make-CERA, Model-2501)

NDSR-03: Providing and fixing of 1 No. Wall Mounted Grab Bar of (Size: 500mm) at fixed height for handicap toilet complete as required. (Make-CERA, Model-2504)

NDSR-04: Providing and fixing of 1 No. Wall Mounted Grab Bar of (Size: 350mm) at fixed height for handicap toilet complete as required. (Make-CERA, Model-2505)

NDSR-04A: Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) a) Counter Top Basin Make-Hindware Topaz (Cat. No.91028)

b) Under Counter Basin Make-Hindware Lara (Cat. No.10095)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 17.7.4: White Vitreous China Flat back wash basin size 550 x 400 mm with single 15 mm C.P. brass pillar tap

NDSR-04B: Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: a) Corner Wash Basin Make-Hindware Claret 560 X 430 (Cat No. 10076)

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms

Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT soap Dish Holder having length of 138mm, readth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per anufacturers specification and direction of Engineer-in-charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 17.10.1.1: 510x1040 mm bowl depth 250 mm

510x1040 mm bowl depth 225 mm

NDSR-04C: Providing & fixing sink cock with regular swinging spout (Wall Mounted Model) of Chrome Plated (C.P.) complete as directed with all necessary fittings. a) Make - Jaquar Catalogue No. - LYR-38347S

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 18.22.2: 150 mm diameter

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 18.52.1: 15 mm nominal bore

NDSR-04D: Providing and fixing uPVC SWR Pipes class B (IS:13592) with all injection moulded fittings(door or plain) viz elbolws, bends, tees, junctions, shoe bends, couplers, offsets, cowel etc. complete including jointing with solvent cement including GI supports, cutting and making good the walls wherever required. Nothing extra will be paid for supports.(Vertical Soil, waste, balcony waste & rain water pipes) a) 75 OD

Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. 110 OD

NDSR-04E: Providing & Fixing uPVC pipe including fittings like elbow tee etc of pressure rating6kgf/cm2quickfit pipes confirming to IS:4985 a) 63 OD

NDSR-5: Providing & Fixing uPVC pipe including fittings like elbow tee etc of pressure rating6kgf/cm2quickfit pipes confirming to IS:4985 Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. a) 40 mm outer dia

NDSR-6: Providing and fixing uPVC floor drain consisting of PVC reducing elbow 110 x 63mm (Grating and pvc pipe to be paid separately), complete as directed by the Project Manager.

Providing and fixing PTMT grating of approved quality and colour. Rectangular type with openable circular lid 18.58.2.1: 150 mm nominal size square 100 mm diameter of the inner hinged round grating

Circular type 18.58.1.1: 100 mm nominal dia

NDSR-7: Providing and fixing uPVC SWR P Trap with minimum 50mm water seal conforming to IS 13592 a) 110 mm inlet & 110 mm outlet.

NDSR-7a: Providing fitting and fixing PVC cowel of ISI make complete as directed and specified. a) 110mm dia. PVC cowel of ISI make

b) 75mm dia. PVC cowel of ISI make

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

NDSR-8: Providing and fixing PVC COP /FCO with suitable insert keys for opening as per approved sample, properly jointed to soil and waste pipe as per requirement, complete as per instructions of the Engineer in charge. a) For 110 mm dia pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. In internal wall - exposed on wall 15 mm OD

NDSR-9: 65 mm nominal outer dia Pipes

NDSR-9A: 80 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed by chiselling or breaking brick wall/C.C/R.C.C and making good to damages. 15 mm nominal outer dia Pipes

18.8.2: 20 mm nominal outer dia Pipes

18.8.3: 25 mm nominal outer dia Pipes

18.8.4: 32 mm nominal outer dia Pipes

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 18.49.1: 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore

NDSR-10: 'Providing & fixing lever operated cPVC ball valve with stainless steel ball / stem. Tested to a pressure of not less than 15 Kg / Sqcm. Including flanges / union, nuts, bolts, washer etc. Complete as required. a) 15 mm nominal bore

b) 20 mm nominal bore

c) 25 mm nominal bore

d) 32 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 18.17.1: 25 mm nominal bore

18.17.1A: 20 mm nominal bore

18.17.2: 32 mm nominal bore.

18.17.3: 40 mm nominal bore

18.17.4: 50 mm nominal bore

18.17.5: 65 mm nominal bore

18.17.6: 80 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 18.19.4.2: 50 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 18.21.2.1: 15 mm nominal bore

NDSR-11: Prividing and Fixing automatic 'NO-Touch ' electric hand-driers complete with all accessories & fittings. (Make: Jaquar Model No. HDR-SAP-M99ACS)

NDSR-12: Providing and fixing Water cooler with inbuilt RO and storage complete including fixing in position.

NDSR-13: Providing & fixing R.O unit with storage complete including fixing in position

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

NDSR-14: Supplying, installing, testing and commissioning of compact self contained skid mounted hydropneumatic system for Upper Level. 2 Nos. vertical in line pumps complete in S.S. coupled with TEFC motor. Pump capacity - 80 LPM each (5psi). Electric control panel with frequency convertor, logic controller relays, pressure switch, pressure transmitter, electrical wiring, cabling with cable tray as specified from panel to pumps, level controller complete with all accessories as per manufacturer specifications. Accessories like ball valves, butterfly valves, NRV's on suction and discharge, pressure gauge suction, discharge header and base frame etc. complete as required. Suction and discharge header complete in S.S. with dead end flanges. Hydropneumatic system as described above.

NDSR-15: Supplying & Installation of standard solar panel with a surface area for 250 litres/day with all necessary internal piping, insulation and accessories.(To be Installed on the terrace of the Proposed Extension.

NDSR-16: Supplying & Installation of standard solar panel with a surface area for 500 litres/day with all necessary internal piping, insulation and accessories.(To be Installed on the terrace of the Proposed Extension

NDSR-17: Supplying, installing, testing and commissioning of 2 Nos. submersible non clog drainage sump pumps with cutter, of continuous duty complete with 3 phase motor with all necessary protection and mechanical seal etc. including electrical starter panel and cabling upto motor as per manufacturer specifications. Complete automation and dry protection of pumps by float level switch. Flow rate: 200 LPM. Head: 15 Mts. Solid Handling: 10-12mm. Location: Sump of lower basement. MOC: SS, Body:SS, Impeller and Shaft.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work. 15mm diameter

20mm diameter

25mm diameter

32mm diameter

40mm diameter

50mm diameter

65mm diameter

80mm diameter

18.12.8a: 100mm diameter

Providing and fixing uPVC Pipes complete (IS: 4985 Class-III) with uPVC pipe fittings e.g. elbows, tees, reducers, unions, plugs, flanges etc. and clamps and jointing with solvent cement including chase cutting and making good the walls etc. wherever required. 20mm diameter

25mm diameter

32 mm diameter

40 mm diameter

50mm diameter

63mm diameter

Providing and fixing gun metal gate valve with C.I. wheel of approved \quality (screwed end) : 15mm dia

18.17.1A: 20mm dia

18.17.1: 25mm dia

18.17.2: 32mm dia

18.17.3: 40mm dia

18.17.4: 50mm dia

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 80 mm dia

100mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with ronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 40mm dia

50mm dia

65 mm dia

80 mm dia

100mm dia

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

Earth work in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m; disposed earth to be levelled and neatly dressed.

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

250 mm dia. R.C.C. pipe

300 mm dia. R.C.C. pipe

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) with precast R.C.C. vertical grating complete as per standard design : 9.28.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :For p ipes 250 to 300 mm diameter

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All Kind of Soil. 2.10.1.2: Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 150 mm diameter

250 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 19.2.2: 150 mm diameter S.W. pipe

250 mm diameter S.W. pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 19.3.2: 150 mm diameter S.W. pipe

250 mm diameter S.W. pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 19.4.3: 180x150 mm size P type 19.4.3.2: With Sewer bricks conforming to IS : 4885

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : 19.7.1: Inside size 90x80 cm and 45 cm deep including precast RCC Cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : 19.7.1.2: With Sewer bricks conforming to IS : 4885

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) 19.7.3.2: With Sewer bricks conforming to IS : 4885

Extra for depth for manholes : Size 90x80 cm. 19.8.2: With Sewer bricks conforming to IS : 4885

Size 120x90 cm. 19.8.2.2: With Sewer bricks conforming to IS : 4885.

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : 19.21.2: For pipes 250 to 300 mm diameter.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. All types of soil. 23.1.1.1: 300 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia,conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 23.3.3: 200 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conformingto IS: 12818, including hire & labour charges, fittings & accessories etc.all complete, for all depths, as per direction of Engineer-in-charge. 23.4.3: 200 mm nominal size dia

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineerin- charge.

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mmmm x 1.6 mm complete, all as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 23.13.3: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 23.14.3: 200 mm clamp

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 18.12.6: 50 mm dia nominal bore

NDSR-18: Supplying & installation of submersible pump set directly coupled with 5 HP motor nominal speed 2900 RPM suitable for operation on 3-phase, 50 cycles, 400 + 5% volts A.C. power supply to give yield of 5000 LPH at a head of 135 mtrs. Total head = 135 Mt. Flow rate = 5000 LPH H P = Minimum 5 HP (Or as per site condition)

NDSR-19: Supply & installation of 80 mm dia column pipe made out of 80 mm dia GI including the cost of fittings complete in all respect Jindal, Hissar/Prakash make 'B' class pipe.

NDSR-20: Providing and fixing MONOBLOCK multistage centrifugal clear water pump set SS-304 casing, SS-304 impeller, SS-316 shaft, CI base with CED coating, complete directly coupled with TEFC induction motor of class "F" insulation & efficiency class EFF-1, 2900 RPM, suitable for operation on 415 volts ±10%, 3 phase, 50 Hz, A.C. supply ( with mechanical seal ), pressure gauges with gunmetal isolation cocks, vibration elimination pads, etc. mounted on a MS base frame bolted to cement concrete foundation including suction header, discharge header, isolation valve & matching companion flanges, etc. complete in all respects and as per speicification with the following capacities: No. of Pumps : 2 (1W + 1S) Capacity : 140 LPM of Each Pump Head : 25 M Note:-1 set consists of 2 nos. of pumps (1Working + 1Standby) Water Transfer Pump

NDSR-20A: 30 HP three Phase Centrifugal monoblock pump set (Crompton Greaves/ Aquatic/ CRI/ V-Guard make) 2900 rpm A class insulation with Star delta Starter ( Crompton Greaves/ Control & Switch Gear/ BCH/ L& T / Siemens make) Fully Automatic citation Dom. water transfer pumps - Zone-01 (A + B) No. of Pumps : 2 (1 Working + 1 Stand by) Capacity : app. 70 LPM each Head : 60 M (complete set as mentioned above)

NDSR-20B: 10 HP three Phase Centrifugal monoblock pump set (Crompton Greaves/ Aquatic/ CRI/ V-Guard make) 2900 rpm A class insulation with Star delta Starter ( Crompton Greaves/ Control & Switch Gear/ BCH/ L& T / Siemens make) Fully Automatic citation Dom. water transfer pumps - Zone-02 (C + D +E) No. of Pumps : 2 (1 Working + 1 Stand by) Capacity : app. 25 LPM each Head : 60 M (complete set as mentioned above)

NDSR-20C: 20 HP three Phase Centrifugal monoblock pump set (Crompton Greaves/ Aquatic/ CRI/ V-Guard make) 2900 rpm A class insulation with Star delta Starter ( Crompton Greaves/ Control & Switch Gear/ BCH/ L& T / Siemens make) Fully Automatic citation Dom. water transfer pumps - Zone-03 (E + F) No. of Pumps : 2 (1 Working + 1 Stand by) Capacity : app. 45 LPM each Head : 60 M (complete set as mentioned above)

NDSR-20D: 25 HP three Phase Centrifugal monoblock pump set (Crompton Greaves/ Aquatic/ CRI/ V-Guard make) 2900 rpm A class insulation with Star delta Starter ( Crompton Greaves/ Control & Switch Gear/ BCH/ L& T / Siemens make) Fully Automatic citation Flushing water transfer pumps - Zone-01 (A + B) No. of Pumps : 2 (1 Working + 1 Stand by) Capacity : app. 62 LPM each Head : 60 M (complete set as mentioned above)

NDSR-20E: 15 HP three Phase Centrifugal monoblock pump set (Crompton Greaves/ Aquatic/ CRI/ V-Guard make) 2900 rpm A class insulation with Star delta Starter ( Crompton Greaves/ Control & Switch Gear/ BCH/ L& T / Siemens make) Fully Automatic citation Flushing water transfer pumps - Zone-02 (C + D +E) No. of Pumps : 2 (1 Working + 1 Stand by) Capacity : app. 35 LPM each Head : 60 M (complete set as mentioned above)

NDSR-20F: 10 HP three Phase Centrifugal monoblock pump set (Crompton Greaves/ Aquatic/ CRI/ V-Guard make) 2900 rpm A class insulation with Star delta Starter ( Crompton Greaves/ Control & Switch Gear/ BCH/ L& T / Siemens make) Fully Automatic citation Flushing water transfer pumps - Zone-03 (E + F) No. of Pumps : 2 (1 Working + 1 Stand by) Capacity : app. 25 LPM each Head : 60 M (complete set as mentioned above)

Providing and fixing vertical Pressure Sand Filter (comprising of minimum 750mm media in four graded layer and minimum Height on Straight 1500mm) fabricated from high performance M.S plate of minimum 10mm thick for shell & 12mm thick for dished ends,(Quality of Steel as per IS:2062 Grade B, thickness as per ASME Section 8),Tested to 5.0 Kg/m2 , internally treated with coal-tar epoxy, air scouring, collection system initial charge of media, M.S face piping with necessary flanges, gaskets, isolating valves, accessories, nuts & bolts, external painting with 2 coats of red oxide primer and enamel paint etc. with suitable foundation boits & other accessories, mounting frame, complete as required & as specified as per directions of the engineer-in-charge. with the following: Discharge : 8.5 m3/Hour Each Suggested dia app. : approx. 1 m or as required

Providing and fixing chemical dozing system consisting of 2 nos. electronic dosing pumps (1W+1S) of approved make with all accessories, suitable to doze chemical solution upto 1 ppm doze (of Sodium Hypo-chloride solution) to a filtered water flow of 8,000 lph. against a pressure of 1.5 kg/cm2 complete with FRP moulded solution holding tank of min. 200 litre with all standard accessories & structural arrangement including suitable foundation bolts & other accessories etc.complete as required and as specified. Note:1 set consists of 2 nos. of pumps(1W+1S)

NDSR-21: Plant room Drainage Sump Pump: Providing and fixing compact monoblock dry motor submersible pumps of suitable rating, with non-clog free flow open impeller, solid handling capacity of upto at least 28mm suitable for operation on 415 volts +10% , 3 Phase, 50Hz, A.C supply, speed 2900 RPM including oil chamber, guide wire for lifting & lowering of pump, M.S. galvanized lifting chain, complete. The pump sets shall be supplied with required accessories & as per specification with the following : (a) Complete piping 80 mm dia common delivery upto 7.5 m in heavy Duty Class 'C' G.I. -- 1 Set (b) 65mm dia Butterfly valve.-- 2 Nos (c) 65 mm dia Flap type Non-return valve.-- 2 Nos (d) Necessary cables from pump set to control panel (position of panel marked on enclosed drawings).- 1 Set (e) Electrical control panel having all necessary accessories & safety devices of standard specifications and suitable for receiving incommer cable from main plumbing panel to conncet sump pump panel complete as required. (Panels with sump pumps near each sump as per site conditions). --1 No. Each set consist of 2 nos.of pumps - 1 working & 1 stand by (Complete set as above with 2 nos. pumps including cost for valves, piping, Control Panel and Cabling, Level Controllers etc as required and as specified) 2.The entire system alongwith pumps & control panel must be sourced from single manufacturer only for unit responsibility. Discharge - 250 LPM Each Total head - 10-15 Meters (minimum)

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work : 18.12.1: 15mm diameter

18.12.2: 20mm diameter

18.12.3: 25mm diameter

18.12.4: 32mm diameter

18.12.5: 40mm diameter

18.12.6: 50mm diameter

18.12.7: 65mm diameter

18.12.8: 80mm diameter

18.12.9: 100mm diameter

18.12.10: 150mm diameter

NDSR-22: Providing and fixing reinforced neoprene rubber vibration eliminators/expansion joints (to provide relief from stresses at pipe flanges) suitable for upto 20 kg/cm2 pressure, as per specification of the manufacturers complete as required and as specified complete as per directions of the engineer-in-charge. 40mm dia

50mm dia

65mm dia

80mm dia

100mm dia

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 18.17.4 50mm dia

18.17.3: 40 mm dia.

18.17.2: 25 mm dia.

18.17.1: 2O mm dia.

15 mm dia.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

SEWAGE TREATMENT PLANT: NDSR-23: Design, supplying, installing, testing & commissioning of MBBR based Sewage Treatment Plant (excluding excavation, back filling & disposal of surplus earth /Civil construction work) for the following duty: Nature of effluent - Domestic Sewage from toilets, canteen kitchen waste water. Daily average flow - 90 Cum / Day pH - 6.5 – 8.5 BOD5 - 250 – 350g/L S. Solids - 200 – 450 Mg/L COD - 450 – 600 Mg/L Oil & Grease - 50 Mg / L Effluent discharge standard after treatment pH - 6.0 – 8.0 BOD5 - Less than 20Mg/L S. Solids - Less than 30 Mg/L COD - Less than 60 Mg/L Oil & Grease - <10Mg/L, Sewage treatment plant shall include the following Civil Unit /Tanks: Screen Chember /Grease Trap 1.5 KL Sewage equalization tank 25KL Treated Water Tank 30KL MBBR tank 12KL Each Tube Settler 7KL Sludge holding Tank 10KL Clear Water Tank 10KL Supply, installation, testing & commissioning of Stainless Steel Perforated, Corrugated Bar Screen with suitable lifting arrangement as per site requirement( Manualy Operated ) Size:500mm X 800mm

Supply, installation, testing & commissioning of level indicator and controller for automatic operation of the system with high/low level alarm with low level stop and high level start logic.

Contractor shall ensure submission of detailed GA drawings (Plan & Section), P & I diagram, schematic diagram for the above mentioned component and additional component if so required for the complete working of the STP and got it approved by the Owner’s Architect / Project Manager / Consultants. Contractor shall also ensure approval of his design process from all concerned local authority Supply, installation, testing & commissioning of non clogging type pumps complete with all accessories, motor of required capacity. Delivery header with isolation valve, pressure gauge on delivery line with isolation cock, level controller (with wiring) to control the level of sump automatically. Pumps shall have following duty: 4.1: Submersible Raw sewage Transfer Pumps ( 2 Nos. -1 working & 1 standby) , Flow rate (each) = 2.5 m3/hr MOC : SS, Head = 10-12 Mtr ( pumps for transfering Sewage from equilisation tank. To MBBR Tank Solid Handling size 35mm)

4.2: Submersible Plant Room Sump Pump ( 2 Nos. -1 working & 1 standby) , Flow rate (each) = 4.6 m3/hr, Head = 10-12 Mtr, MOC : CI, Solid Handling size 20mm.

4.3: Sludge Recircualtion Pumps with CI body & CI impeller pump 1 working, Capacity : 2 m3/hr, Head : 12 -15 M, RPM : 2900. (Solid handling size for above pumps shall be 7mm).

Supplying, installing, testing & commissioning of Horizontal centrifugal water pumps,CI Body & Impeller along with motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, stainer at suction. Mechanical seal, suitable vibration elimination pads of approved design, drain pipe with valve for the pump. The pump shall be suitable for 415±10% volts 3 phase AC supply 5.1: Filter feed water pump, Capacity : 4.5 m3/hr, Head :25-30M, RPM : 2900, No. of Pumps (1 working + 1 standby)

Air diffusion system shall include the following: 2 Nos. twin type rotary air blowers (One working & one standby) capable of delivering 100m3/hr of free air at 0.5 kg/cm2 driven through “V” belt or directly coupled through flexible coupling to a TEFC motor of suitable HP, Suitable for 415 ± 10% volts, 3 phase, 50 cycles A/C supply.

Air piping shall comprise of pipes with PVC Header complete with all fittings such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, etc cutting chases & making good. Contactor to submit detailed P & I indicating their proposal

Non clog type air retrieval diffussion(EPDM) system capable of handling 5-8 cfm of air with oxygen transfer efficiency of 3-4% per/meter water depth. Air dispersion grid shall be assembled in modular form so that they can be replaced / repaired easily from plat form at the top. ( fine bubble epdm membrane diffusers)

Providing and fixing all piping (as described below) and isolation control valves for making the system complete. PVC : Submerged air piping, Air Piping PVC :Pumped effluent & tank overflow pipe line PVC : Interconnecting pipe line after delivery header of pump/ filter Designing, supplying, providing, fixing, testing and commissioning of STP as mentioned above.

Supplying, installing, testing and commissioning of FRP vessel filter. Filter shall be suitable for working pressure of 3.0 kg / cm² and shall include media, standard fittings like pressure gauges, sampling cock, rinse drain, vacuum breaker. 8.1: Multigrade pressure sand filter media Flow rate : 4.5 m3/hr, Filteration velocity : 10000 lit/hr/sqm, Filter Diameter : 600mm

8.2: Activated Carbon Filter , Flow rate : 4.5 m3/hr, Filteration velocity : 10000 lit/hr/sqm Filter Diameter : 600mm

MBBR/FAB media for MBBR/FAB tanks

Clarifier Mechanism & Tube deck media for secondary clarifier

Filters press 18"X18" 12 no. plate with supply of new screw pump(1Working) with all fittings & accessories .Semi automatic Manual operated

Supplying & fixing of Flow Meter cum Totalizar

Chlorine dosing System 0-6LPH pump wit 100 ltr tank

Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of motor control centre shall be fabricated with reinforcement of suitable size angle iron, channel ‘T’ sections irons and/or flats wherever necessary. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications with 2 coats of red oxide primer and final approved shade of powder coated paint. 2 Nos. earthing terminals shall be provided for 3 phase, 4 wire, 50 Hz supply system. Lifting hooks shall also be provided in case of large panels. (ALL MPCB, CONTACTOR,OVERLOAD RELAY Shall be L&T & ABB)

Supplying, installing, testing & commissioning of Cables , Conector, Cable Trays, to make Electrical Installation Complete.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 200 mm dia

150 mm dia

100 mm dia

80 mm dia

65 mm dia

50 mm dia

40 mm dia

32 mm dia

25 mm dia

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 150 mm dia

NDSR-1A: 100 mm dia

NDSR-1B: 80 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 14.7: 150 mm dia

100 mm dia

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 18.7.4: 50 mm dia

25 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 11.7: 200mm dia

150 mm dia

100 mm dia

80 mm dia

65 mm dia

50 mm dia

40 mm dia

Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 200 mm dia

150 mm dia

NDSR-1C: Providing ,Fixing ,Testing & Commissioning of air Release Valve a) 25 mm dia

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required

B (HYDRANT SYSTEM): Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal / Stainless Steel cap and chain as required : Single headed Gunmetal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 17.1: 30m

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : 16.1: Gun Metal

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : 18.1: Gun Metal

NDSR-1A: Providing & fixing of weather proof hose cabinets fabricated from 16 S.W.G. M.S. Sheet with centre pening full front glass door and locking arrangement, suitable to accommodate one landing valve (Yard Hydrant ), 2nos.15M long hoses and 1 no. Branch pipe with nozzle . The cabinet shall be painted with one coat of primer and 2 or more coats of synthetic enamel paint of approved make & shade and shall be suitably mounted on a raised masonry platform complete as reqd.(Make:self Fabricated) 2100 X 1200 X450

NDSR-1: Supplying and fixing of Fire Man's Axe with heavy insulated rubber tested upto 20 KV and confirming to IS :926.

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 19.1: 2 way-100 mm dia M.S. Pipe

4 way - 150 mm dia M.S. Pipe

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : 21.1 Pendent Sprinkler

Upright Sprinkler

Horizontal side wall sprinkler

Concealed sprinkler

NDSR-2A: C (FIRE EXTINGUISHERS & MISC. ITEMS): Supply, Installation, Fixing of CARBON DIOXIDE Fire Extinguisher confirming to IS: 2878 with ISI Mark. (Extinguisher will be TROLLEY MOUNTED)(6.5 KG) BRAND : FIRESTOP / FIREND / FIRE SHIELD.

NDSR-2B: Supply, Installation, Fixing of WATER CO2 Fire Extinguisher confirming to IS: 940 with ISI Mark and CO2 Cartridge will be confirming to IS: 4947 with ISI Mark.(09 LITERS) BRAND: FIRESTOP / FIREND / ESHIELD

NDSR-2C: Supplying and fixing of fire withdrawl connection of aluminium body with instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

NDSR-2: Providing and fixing 25 mm dia inspecting & testing assembly with gunmetal valve, gunmetal sight glass, bypass valve & connected to drain line.

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 19.6.5: 450 mm dia. R.C.C. pipe

300 mm dia. R.C.C. pipe

NDSR-3: Providing & fixing SS cabinet fabricated from 16g SS 304 sheet with full front glass door and locking arrangement duly painted with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade and suitably mounted on a wall or raised masonry platform as required (Approx 0.75m x 0.6m x 0.45m)

D (FIRE PUMPS & ACCESSORIES): Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (d) Suitable cement concrete foundation duly plastered and with anti vibration pads. 4.1: 900 lpm at 35 m Head

NDSR-2: Providing and fixing liquid level controller for fire pump to stop fire pump in case of low level of water in tank , cost of conduit, cable and panel including making connection to pump panel and commissioning complete. Float type Sensor with panel and installation

NDSR-3: Providing and fixing rubber expansion joint (to provide relief from stresses at pipe flanges) as per specification of the manufacturers and direction of Engineer in chief PN-16 rating a) 100 mm dia

B (FIRE PUMPS & ACCESSORIES): Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. d) Suitable cement concrete foundation duly plastered 1.4: 2280 lpm at 88 m Head

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard pecification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 2.4: 2280 lpm at 88 m Head

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 3.2: 180 lpm at 70 m Head

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required : 24.3: 150mm dia

NDSR-4: 30 HP three Phase Centrifugal monoblock pump set (Crompton Greaves/ Aquatic/ CRI/ V-Guard make) 2900 rpm A class insulation with Star delta Starter ( Crompton Greaves/ Control & Switch Gear/ BCH/ L& T / Siemens make) Fully Automatic citation. Dom. water transfer pumps - Zone-01 (A + B) No. of Pumps : 2 (1 Working + 1 Stand by) Capacity : app. 70 LPM each Head : 35 M (complete set as mentioned above)

Variable Refrigerant Flow/Variable Refrigerant Volume System: Supply Installation Testing and Commissioning of Imported Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor Units suitable for cooling and heating, having all hermetically sealed inverter type Scroll / Twin rotary Compressor(s), minimum two compressors for 20 HP & above modules with Vapour Injection Technology ,microprocessor based controller, top discharge type condensing units with R410 A refrigerant, vibration isolators with suitable foundation etc. complete as required . The unit shall deliver the rated capacity at AHRI conditions and work even at 54 Deg C ambient temperature without tripping. The unit shall be suitable to work on 400 V+/-10% 3 phase , 50 Hz AC power supply.The Unit should have feature for Refrigerant Cooled Electronic PCB . The COP at AHRI in Cooling mode should be 4.0 & above . The quoted cost sould include custom clearence , transit cost , ocean frieght & forwarding charges . 1.01: (Mini Secreteraite Building and Auditorium)

Supplying, installing, testing and commissioning of Wall mounted type indoor units each complete with coil, filter, etc. Air conditioners with evaporating unit comprising of cooling coil, blower with motor , Corded Remote Control and 220 volt, 1 phase, 50 Hz, AC supply all and as per specifications. 2.01: 2.0 TR (Wall Mounted)

Supply Installation Testing and Commissioning of DX double skin air handling units Floor Mounted type with 24Ga pre coated G.I. outer skin & 24 Ga G.I. inner skin with 40 mm thick PUF insulation of density 42+2 kg/m3 horizontal type AHU complete with DIDW fan, fan motor drive, 4 row deep DX cooling coil, MERV-8 pre filters, mixing box, device, with fire rated canvass connection between CSU and supply air duct, thermal break profile, vibration isolator pad, Expansion Kit , communication Kit and wired remote controlleras per specifications complete etc as required. 3.01: 8000 cfm, 20 TR - 30mm SP

4 Way Cassette indoor unit: Supply Installation Testing and Commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve ,outer cabinet, drain pump grill, necessary supports, vibration isolation, corded remote control etc suitable for operation on 230 V +- 10% 50 Hz AC supply 4.01: 2.01 TR

Supply Installation Testing and Commissioning of following minimum capacity High Static Type Ducted Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve ,outer cabinet, drain pump grill, necessary supports, vibration isolation, corded remote control etc suitable for operation on 230 V +- 10% 50 Hz AC supply 5.01: 5.50 TR

3.6 TR (Treated Fresh Air Unit )

4.00 TR (Treated Fresh Air Unit )

8.00 TR (Treated Fresh Air Unit )

Y Joints: Supply, fixing and commissioning of refrigerant joint / Branch distibutors between Outdoors with nitrile rubber insulation, supporting etc. complete as required.

Supply, fixing and commissioning of refrigerant joint / Branch distibutors between Indoors with nitrile rubber insulation, supporting etc.complete as required.

Supply installation Testing and Commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRF/VRV system, complete with fittings, with suitable adjustable ring type hanger supports, jointng/brazing including accessories insulated with XLPE Class O tubular insulation/with Class O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specification etc as required: 7.01: 6.4 mm dia (OD) (soft drawn) with appropriate tube thickness with 13mm thick insulation

9.5 mm dia (OD) (soft drawn) with appropriate tube thickness with 13mm thick insulation

12.7 mm dia (OD) (soft drawn) with appropriate tube thickness with 13mm thick insulation

15.86 mm dia (OD) (soft drawn) with appropriate tube thickness with 13mm thick insulation

19 mm dia (OD) (Soft/Hard drawn) with appropriate tube thickness with 13mm/19mm thick insulation

22.2 mm dia (OD) (Hard drawn) with appropriate tube thickness with 19mm thick insulation

28.58 mm dia (OD) (Hard drawn) with appropriate tube thickness with 19mm thick insulation

31.8 mm dia (OD) (Hard drawn) with appropriate tube thickness with 19mm thick insulation

34.9 mm dia (OD) (Hard drawn) with appropriate tube thickness with 19mm thick insulation

38.1 mm dia (OD) (Hard drawn) with appropriate tube thickness with 19mm thick insulation

41.27 mm dia (OD) (Hard drawn) with appropriate tube thickness with 19mm thick insulation

44.5 mm dia (OD) (Hard drawn) with appropriate tube thickness with 19mm thick insulation

Drain Piping: Drain Piping: Supply Installation Testing & Commissioning of rigid UPVC piping with fittings, supports as per specifications and duly insulated with 6 mm thick closed cell nitrile rubber insulation etc. complete as required. 8.01: 25 mm dia ( with 6 mm nitrile rubber Insulation)

32 mm dia ( with 6 mm nitrile rubber Insulation)

40 mm dia ( with 6 mm nitrile rubber Insulation)

Ducting: Supply Installation Testing and Commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per pproved drawings and specifications of following sheet thickness complete as required. 9.01: Thickness 0.63 mm Sheet

Thickness 0.80mm Sheet

Thickness 1.00mm Sheet

Thickness 1.20mm Sheet

Round Duct

1mm to 899mm -- 24G GSS Round Duct

Supply Installation Testing and Commissioning of Site fabricated GSS sheet metal rectangular/ round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 10.01: Thickness 0.63 mm Sheet

Supply and fixing of following thickness duly laminated aluminium foil finish closed cell Nitrile rubber ( Class O) insulation on duct after applying suitable adhesive for Nitrile rubber . The joints shall be sealed with 50 mm wide and 3mm thick self adhesive nitrile rubber insulation complete as per specifications and as required. (a)13 mm thick insulation with Aluminium foil

Supply, installation and testing of acoustic lining of ducts with glass wool of 24 Kg/sqcm , the glasswool shall be covered with RP tissue paper and fixed with roofing nut and bolt complete as per specification and complete as per requirement.. Thermal conductivity of the insulation material shall not exceed 0.047 W/moK at an average temperature of 20oC. 12.01: 25 mm thick acoustic lining

Supply installation and fixing of fire retardant non porous double layer flexible connection between each AHU as complete as required.

Grilles / Diffuser: Supplying & fixing of powder coated extruded aluminum Supply Air Grills with aluminum volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminum Return Air Grills with louvers but without volume control dampers complete as required.

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminum with aluminum volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminum without volume control dampers with anti smudge ring & removable core.

Supply & Installation of extruded aluminum volume control damper with blades, adjustable lever, frame etc for Supply Air and Fresh Air Connected to AHU as per specifications and drawings as complete as required.

AIR TRANSFER GRILLES: Supply, Installation and Testing of extruded aluminium powder coated air transfer grilles to be provided at the door of toilets/pantry.

Supply, Installation , Testing and Balancing of double louvered supply air grilles as per approved shop drawings and specifications complete with key operated aluminium volume control dampers.

Supply, Installation,Testing and Commissioning of motorised fire dampers suitable for at least 90 minutes fire rating as per the specifications and approved shop drawings. Quoted price shall be inclusive of copper control wiring as required. Bare Fire Dampers

Spring return action type actuator complete with control panel and temperature sensor. Torque not less than 16NM

Supply, Installation and Testing of GI box type volume control dampers as per the specifications and shop drawings.

Supply, Installation and Testing of GI multi blade type louver dampers as per the specifications and shop drawings.

Supply, Installation and Testing of extruded aluminium powder coated louver with GI wire mesh to be installed outside for discharge of exhaust air from exhaust fans as per the specifications and shop drawings. Sample of louvers to be got approved from consultants and Clients prior to procurement.

Supply, Installation and Testing of Bird Screens with GI wire mesh to be installed at the suction of fresh air/discharge of Exhaust air as per the specifications and shop drawings. Sample of bird screen to be got approved from consultants and Clients prior to procurement.

Supply, Installation and Testing of non return dampers. NRDs to be installed in the ducts as per he specifications and shop drawings.Sample of NRDs to be got approved from consultants and Clients prior to procurement.

Supply, Installation , Testing of 125mm deep antivibration flexible joints at the outlet of air Fans units/inline fans. Flexible hall be constructed using imported fire retardant connections fabric with extruded aluminium frame/flange on both sides of approved make.

Cable Tray: Fabrication, supplying and installing of GI tray with cover of following sizes of horizontal and vertical bends, reducers, tees, cross members & other accessories etc. as required and duly supported from the ceiling with dash fastness including painting of suspenders required for accomodating/ laying of refrigerant pipes as complete as required. 15.01: 150 x 50 x 1.6 mm

Supply & Installation of control cum transmission wiring of 3 core x 1.5 sqmm Shielded copper in suitable pvc conduits between indoor and outdoor unit as complete as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. (a)25 mm dia

Supply and laying / fixing on surface of Power cable of following sizes XLPE insulated aluminium armoured conductor cable to VRF outdoor unit from main electrical panel. The cost shall include all necessary supports clamps etc as complete as required. (a)4C x 25 sqmm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (a)4C x 25 sqmm

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Refrigerant gas R-410 for top up as complete as required.

Supply installation Testing and Commissioning of Touch Type centralised controller suitable for Controlling 64 IDU's to connect all indoor units as complete as required.

MS Fabricated (Heavy Duty ) ODU Frame

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/MCCB/Isolator) 24.01: Single door

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 23.01: 63 A

Corrosion Prevention Chemical Coating for VRF Air- Conditioning System that shall be Basecoat - Hybrid Epoxy Antirust + Top coat - Silane Hybrid Dual Barrier 24.01: VRF Outdoor Unit

Hi Wall Split Indoor Unit a) 2.0 TR(Wall Mounted)

4 Way Cassette Unit a) 2.01 TR

Ductable Unit a) 5.50 TR

e) 3.6 TR (TFA Ductable)

f) 4.0 TR (TFA Ductable)

g) 8.00 TR (TFA Ductable)

Dx Type AHU a) 8000 CFM

Supply, Installation, Testing and Commissioning of axial flow fans (Vane axial type) complete with MS casing, impeller and flame proof motor with class 'F" insulation for make - up air system and class "H" insulation for smoke evacuation system as shown in the drawings and as per the specifications. Fans with class "H" motors should be suitable for operating for mimimum 2 Hrs at 250-300 degC temp. Fan Casing should be provided with Special Designed Integral Straightening Vanes to reduce turbulence, provide high performance & low noise level. Axial fans shall be suitable for operation on 415±10% volts, 50Hz, 3 phase AC power supply. Axial flow fans shall be provided with inlet and outlet cones fabricated at site using GS sheet having thickness not less than 20G and necessary vibration isolation arrangement including spring type vibration isolators and rubber groumet etc. as required. Fans shall be IP-55 rated. All fans should be AMCA certified. Motor shall be EFF-2 type. Fan Capacity S.P Motor Area being Fan No. (Cfm) (mmWG) Rating/Class fed Dia/RPM (HP) (mm) Basement - Car Parking a) VAF-1 28500 45-50 20 Basement 1250/960

Class'H' Normal/Smoke Exhaust b) VAF-1 25000 45-50 20 Basement 1250/960

Class'H' Normal/Smoke Exhaust c) VAF-3 10500 45-50 10 Basement 900/1450

Basement - Auditorium : Class'H' Normal/Smoke Exhaust d) VAF -4 21500 45-50 10 Basement 1250/960

Class'H' Normal/Smoke Exhaust e) VAF -5 5000 35-40 5.5 Lift 900/1450 Class'H' Normal/Smoke Exhaust Maximum Noise Level for above fans shall not exceed 75dBA@3M

TUBE AXIAL FANS : Supply, Installation, Testing and Commissioning of axial flow fans (tube axial type) complete with MS casing, impeller, flame proof motor with class 'F" insulation for make - up air system and class "H" insulation for normal and smoke evacuation of basement as shown in the drawings and as per the specifications. Fans with class "H" motors should be suitable for operating for mimimum 2 Hrs at 250-300 degC temp. Axial fans shall be suitable for operation on 415±10% volts, 50Hz, 3 phase AC power supply. Axial flow fans shall be provided with inlet and outlet cones fabricated at site using GS sheet having thickness not less than 20G and necessary vibration isolation arrangement including spring type vibration isolators and rubber groumet etc. as required. Fans shall be IP-55 rated. All fans should be AMCA certified. Motor shall be EFF-2 type. Fan Capacity S.P Motor Area being Fan No. (Cfm) (mmWG) Rating/Class fed Dia/RPM ( HP) (mm) Basement - Car Parking a) TAF-1 46500 45-50 20 Basement 1250/1450

Class'H' Smoke Exhaust b) TAF-2 31000 45-50 20 Basement 1250/1450

Class'H' Smoke Exhaust c) TAF-3 26000 45-50 20 Basement 1250/1450

Class'H' Smoke Exhaust Basement - Auditorium d) TAF-4 18500 45-50 15 Basement 1250/1450 Class'H' Smoke Exhaust

FRESH AIR FAN (FLOOR MOUNTED): Supply, Installation, Testing & Commissioning of Fan Filter Units (FFU) comprising of following as per the specifications : a.) Casing of FFU shall be in double skin construction. Inner skin shall be constructed out of 24 gauge plain GS sheet & outer skin in 24 gauge pre-plasticized GS sheet sandwitched between 25mm thick injected PU foam insulation of density not less than 40 Kg /CuM and complete with inspection doors and marine light, limit switch including control wiring as required. b. Fan section complete with backward curved DIDW type centrifugal fan/s, EFF2 type TEFC squirrel cage induction motor suitable to operate on 415+10%V, 50Hz, 3 phase AC power supply and belt drive package. Fan outlet velocity shall not be more than 2000 FPM (10.16 MPS). c. FFUs shall be complete with Pre- Filter section complete with 50 mm thick washable synthetic fiber filters. Velocity across the filters shall not exceed 500 FPM. d. In addition to the above, Fan Filter Units shall be provided with adequate vibration isolation pads and fire retardent flexible canvass connections made out of canvass sleeve. Sizes of Fan Filter Units shall not exceed as mentioned in the design drawings and FFUs shall conform to the design parameters mentioned in specifications. Floor mounted type Fan Filter Units (FFUs) as described above with following duty parameters : M/c No Capacity S.P Motor Area to (Cfm) (mmWG) Rating be fed (HP) Mini Secreteraite ( Courtyard) FFU-1 17000 45-50 10.0 Courtyard

EXTRACT FAN SECTION- FLOOR MOUNTED: Supply, Installation, Testing & Commissioning of Extract Fan Sections (EFS) comprising of following as per the specifications : a. Casing of EFS shall be in double skin construction. Inner skin shall be constructed out of 24 gauge plain GS sheet & outer skin in 24 gauge pre-plasticized GS sheet sandwitched between 25mm thick injected PU foam insulation of density not less than 40 Kg /CuM and complete with inspection doors and marine light, limit switch including control wiring as required. b. Fan section complete with backward curved DIDW type centrifugal fan/s, EFF2 type TEFC squirrel cage induction motor suitable to operate on 415+10%V, 50Hz, 3 phase AC power supply and belt drive package. Fan outlet velocity shall not be more than 2000 FPM (10.16 MPS) c. In addition to the above, Extract Fan Section shall be provided with adequate vibration isolation pads and fire retardent flexible canvass connections made out of canvass sleeve. Sizes of Extract Fan Sections shall not exceed as mentioned in the design drawings and EFS shall conform to the design parameters mentioned in specifications. Floor Mounted type Extract Fan Section(EFS) as described above with following duty parameters : M/c No Capacity S.P Motor Area to (Cfm) (mmWG) Rating be fed (HP) EF-1 17000 50 10.0 Courtyard

INLINE FANS (Single Phase): Supply, Installation, Testing & Commissioning of circular /rectangular inline fans for exhaust air complete with sheet metal casing, direct driven centrifugal fan, motor with proper protection and inspection door. Fan shall be suitable for operation on 220+6 % volts, 50 Hz,1phase AC power supply. Flanges to be provided on both sides to facilitate duct connections. Fan shall be installed as shown in the drawings and will be of following characteristics : All single phase inline fans shall be provided with factory fitted speed regulators. All Fans Should be complete with Plug Top & necessary power cable. Fan Capacity S.P Area to No. (Cfm) (mmWG) to be exhausted a) IF-1(Circular) 500 14-15 Toilet - SE. Building

b) IF-2(Circular) 1000 20-25 Toilet - Audi. Building

b. 450 mm dia 250 RPM fan,single phase. NOTE: All hardware for module furniture shall be of Hettich/Hafele has dorma make as shall be getting approved by Architect.

Reception Table: Dimension: 3500mm(L) x 750mm(D) x 1050mm(H) with 2nos pedstal Supplying, and placing in position of reception Table as per Image/drawing . The Table top made up of 36mm thick prelam particle board and understructure shall be made of 25mm thick prelam particle board with 2mm thk pvc edge banding . Modesty & side panel shall be 25mm thk prelam particle board with 2mm thk pvc edge banding . Table top height will be 750mm from the floor level & one additional top at the height of 300 mm above the table top rest on SS stud/prelam vertical panel . overall ht of the table 1050mm. The working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot temperature. Provision of PLPB Mobile pedestal of 400mmLx 450mmD x600mmHT (2 drawer + 1filling). Pedestal Top made out of 18mm thick pre laminated particle board and rest all storage to be made out of 18 mm thick prelam particle board . All exposed edges shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The Product should be from the manufacture of approved make of Godrej, Durian, HNI, Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Side/Back Storage with Reception Table: Dimension: 1800mm(L) x 450mm(D) x 750mm(H) Supplying , and placing in position of storage as per photograph/drawing. The complete storage unit shall be made up of 18 mm thick prelam particle board with 2mm thk pvc edge banding . The storage shall be provisioned with shelves and 2 nos compartments. The storage shall have openable shutters with handles and locking arrangements. The Product should be from the manufacture of approved make of Godrej, Durian, HNI.Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Reception Chair: Supplying, and placing in position of 360 degree revolving medium mesh back chair as per Image. Styled for the contemporary office space the chair boasts of a curved backrest with a central console for lower back support. this helps to improve posture and provides comfortable seating all day long. The chair is fixed to a sleek chrome vaulted base with its individual prongs powered by nylon castors. A complete executive office chair, Jordon will bring you comfort like never before. Material & Subtype:Mesh, Dimension:(W)610mm X (D)470mm X (H)1040mm, Back Type:Medium Back, Base:Chrome Base, Base Type:Revolving, Maximum Seating Height:1040mm, Minimum Seat Height:940mm, Function:Revolving::Pneumatic Height adjustment::Tilt Tension adjustment::Synchro tilt Locking:PU adjustable handle : adjustable lumbar support . The pneumatic height adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs extension force. The Seat are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3.The Product should be from the manufacture of approved make of Godrej, Durian, HNI.Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Conference Table: Dimension:(L)4550mm X (D)1200mm X (H)750mm: Supplying and placing in position of conference Table as per photograph/drawing. The table top shall be made out of 36mm thick prelam particle board with2mm thk pvc edge banding.The Table top shall be supported with36mm thick Side panel and modesty panels shall be made out of 25mm thick prelamparticle with 2mm thk pvc edge banding.. All exposed edges shall be provided with machine pressed pvc edge banding. Provision of flip top box for wire management and raceway under the table top for wires flow. The Product should be from the manufacture of approved make of Godrej, Durian, HNI, Herman Miller. complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Conference Main Chair: Supplying and placing in position of 360 degrees revolving high back chair as per photograph. The chair of Size :-(W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design contour lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered with leatheritte and cut foam. The leatherette upholstery in the chair has the look and feel of top grain leather. The chrome plated loop armrest with padded upholstery is provided for extra comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/-2kg /m3) Dimensions . The backrest has a foam of 28kg/m3. The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller. complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Conference Visitor Chair: Supplying and placing in position of 360 degrees revolving medium back chair as per photograph. The Craze chair of Size :-(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design contour lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered with leatheritte and cut foam. The leatherette upholstery in the chair has the look and feel of top grain leather. The chrome plated loop armrest with padded upholstery is provided for extra comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/-2kg /m3) The backrest has a foam of 28kg/m3. The Product should be from the manufacture of approved make of Godrej, Durian, HNI, Herman Miller. complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Conference Visitor Chair (along the wall): Supplying and placing in position of medium back cantilever chair of size: (W)610mm X (D)505mm X (H)990mmas per Image.A contemporary design with an all black finish, the chair is a staple in every office setting. A double padded cushion encased in an all black premium leatherette makes for one comfy seat. The side padding and the headrest sit snugly providing added lumbar support to the user. Available in multiple formats to suit your individual needs. Material & subtype:Premium Leatherette, Colour & Colour Family:Black, Dimension(W) 610mm X (D)505mm X (H)990mm, Back Type:Cantilever, Base:Cantilever Frame, Base Type:Cantilever, Maximum Seating Height:19".The Seat & back are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3. The backrest has a foam of 28kg/m3.The Product should be from the manufacture of approved make of Godrej, Durian, HNI.Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Linear Workstation for Accounts Branch/ Establishment Branch: Dimension (L)1200mm X (W)600mm X (H)1200mm. Supplying and placing in position of sliding tile base modular Workstation as per photograph/drawing. Free standing partition height 1200mm and should be minimum of 65-67mm thick. Partition inner frame is 1.1-1.2 mm thick mild steel. Horizontal and vertical trims are made out of extruded aluminum of 1.mm thick. All Panels/trims shall be powder coated with 50 microns. Aluminum trims are elegantly fixed with special fixtures in the partition. The frame work shall be fitted with 9mm thick pre laminated Particle tiles of approved shade. Partition shall have provision for pin up board with fabric/ white marker/ laminated of approved shade. Partition framework shall have adequate provisions for the movement of electric data cables at desired 2 levels; one at skirting and another above / below the table top. The complete partitioning work shall be carried out as per the approved drawing. Tabletop for workstation made up of 25mm thick pre laminated Particle board of approved shade. The worktop shall be supported on minimum 2mm thick powder coated CRCA brackets and side panels. Side’s panels should be made from 18mm thick pre laminated Particle board of approved shade. All working or non working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot temperature. . Provision of one PVC keyboard tray and Metal CPU trolley with lockable castors for each seating. Also a provision of Mobile Pedestal Unit (size:- L-400mm x D-450mm x H-600mm) with a combination of 2 drawer & one filing drawer. The pedestal storage unit shall be made of 18 mm thick prelaminated Particle board with provision of handles & central Locking arrangement.The Product should be from the manufacture of approved make of Godrej, Durian, HNI, Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Workstation chair for Accounts Branch/ Establishment Branch. Supplying, and placing in position of 360 degree revolving medium mesh back chair as per Image. Styled for the contemporary office space the chair boasts of a curved backrest with a central console for lower back support. this helps to improve posture and provides comfortable seating all day long. The chair is fixed to a sleek chrome vaulted base with its individual prongs powered by nylon castors. A complete executive office chair, Jordon will bring you comfort like never before. Material & Subtype:Mesh, Dimension:(W)610mm X (D)470mm X (H)1040mm, Back Type:Medium Back, Base:Chrome Base, Base Type:Revolving, Maximum Seating Height: 1040mm, Minimum Seat Height:940mm, Function:Revolving::Pneumatic Height adjustment::Tilt Tension adjustment::Synchro tilt Locking:PU adjustable handle : adjustable lumbar support . The pneumatic height adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs extension force. The Seat are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3.The Product should be from the manufacture of approved make of Godrej, Durian, HNI. Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Medium Height Storage for Accounts Branch: Supplying, and placing in position of storage @ 1200mm height as per photograph/drawing . storage unit having Openable shutters with shelf in it. The modular storage unit top shall be made from 18 mm thick pre-laminated particle board and rest of the sides as well as shelves and shutter to be made up of 18 mm thick pre-laminated particle board while back to be made of 8 mm thick pre-laminated particle board. All edges to be provided with 2 mm thick PVC lipping. Each unit to have openable shutters with locking provision.The Product should be from the manufacture of approved make of Godrej, Durian, HNI.Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge. Dimension: 1500mm(L) X 450mm (D) X 1200mm(H)

Dimension: 1800mm(L) X 450mm (D) X 1200mm(H)

Dimension: 3700mm(L) X 450mm (D) X 1200mm(H)

Dimension: 3000mm(L) X 450mm (D) X 1200mm(H)

Dimension: 1240mm(L) X 450mm (D) X 1200mm(H)

Main Table for officer's Cabin: Main Table Dimesnion: (L)2400mm X (D)900mm X (H)750mm All over Side Runner Dimension: (L)2100mm X (D)450mm X (H)650mm Supplying, and placing in position of a straight line table with wire manager hole as per photograph/drawing. The main desk of size 2400mm (L) X 900mm (D) X 750mm (H) shall be made out of 42mm thick prelam particle board with the approved shade. Table top supported with side panels and modesty panel. The side panels made out of 42mm thick pre lam Particle board & modesty panel made out of 36mm thk pre lamParticle board of approved shade. All working or non working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot temperature. Provision of Pop-up - cable manager box in the table .The Fixed Side Runner attached to the table of all over size 2100mm (L) x 450mm (D) x 650mm (H) has a provision for three drawer with locking facility , two openable shutters with locking arrangement & one open storage with shelf.The another side panel of table top having a provision of two attached drawer as per photograph. The table top rest on SS studs for design purpose same as per image. The Product should be from the manufacture of approved make of Godrej, Durian, HNI.Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Main Chair for officer's Cabin: Supplying, and placing in position of 360 degree revloving high back chair as per Image.The premium upholstery is an added touch of extra class. With its supple leather upholstery. Equipped with a multi-locking knee tilt mechanism and adjustable arms this chair is is high on back support and comfort.Size: (W)610mm X (D)500mm X (H)1300mm, Leather: Semi Aniline Leather, Function: Revolving::Pneumatic Height Lift::Adjustable Armrest::Multilocking Knee Tilt, Maximum Seating Height: 24",Minimum Seat Height: 20.86", Base :Chrome Base, Locking Mechanism: Multi-Locking Knee Tilt.The pneumatic height adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs extension force. The Seat are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 30-32 kg/m3. The Product should be from the manufacture of approved make of Godrej, Durian, HNI.Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Visitor Chair for officer's Cabin: Supplying, and placing in position of 360 degree revloving medium back chair as per Image. The premium upholstery is an added touch of extra class. With its supple leather upholstery. Equipped with a multi-locking knee tilt mechanism and adjustable arms this chair is is high on back support and comfort.t.Dimension (W)640mm X (D)500mm X (H)1130mm, Leather: Semi Aniline Leather, Function: Revolving::Pneumatic Height Lift::Adjustable Armrest::Multilocking Knee Tilt, Maximum Seating Height: 24",Minimum Seat Height: 20.86", Base :Chrome Base, Locking Mechanism: Multi-Locking Knee Tilt.The pneumatic height adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs extension force. The Seat are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 30-32kg/m3.The Product should be from the manufacture of approved make of Godrej, Durian, HNI, Herman Miller. complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Main Table for Cabin's room/ PA room Main Table Dimension : 1800mm(L) X 750mm(d) x 750mm(h) Side Runner Dimension: 1000mm(L) X 450mm(d) x 750mm(h) Supplying, and placing in position of main Table as per drawing. The Table top made out of 25mm thk prelam particle board with 2mm thk pvc edge banding & side panel & modesty panel made up of 18mm thick prelam particle board .The working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot temperature. Provision of 3 drawer mobile pedestal (size:- L-400mm x D-450mm x H-600mm) attached to the table top. Pedestal Unit have a combination of 2 drawer & one filing drawer. The pedestal storage unit shall be made of 18 mm thick prelaminated Particle board with provision of handles & central Locking arrangement. The table have a provision of free standing Side Storage of size 1000mm L x 450mm D x 750mm Ht., Storage Top made out of 18mm thick pre laminated particle board and rest all storage to be made out of 18 mm thick prelaminated particle board . All exposed edges shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. Storage having provision of 3 drawer unit, one openable shutter, one open storage with handle & central locking provision. The Product should be from the manufacture of approved make of Godrej, Durian, HNI, Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Main Chair for Cabin's room/ PA room. Supplying, and placing in position of 360 degree Revolving High back chair. Minimum size 610mm (W) x 1118mm (H) x 483 (D) and Maximum size 610mm (W) x 1219mm (H) x 483mm (D). The chair with arm rest of which seat shall be made up of 12mm thk hot pressed two pieces plywood upholstered with fabric in front and back in ABS moulded with polyurethene foam. Provision of tilt tension adjustment,upright locking facility and full 360 degree swivel mechanism . The base should be made of crome finnished and fitted with 5 nos twin wheel castor. The pitch centre diameter of the base along with castors should bot exceed 660mm, hydralic height adjustment stoke should be 60-80mm and shall be operated at 30 kg. extension force. Seat & back are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 28-32 kg/m3. The backrest has a foam of 28D.The Product should be from the manufacture of approved make of Godrej, Durian, HNI Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Visitor Chair for Cabin's room/ PA room. Supplying, and placing in position of Revolving medium back chair . Minimum size 610mm (W) x 914mm (H) x 483 (D) and Maximum size 610mm (W) x 1016mm (H) x 483mm (D). The chair with arm rest of which seat shall be made up of 12mm thk hot pressed plywood upholstered with fabric in front and back in ABS moulded with polyurethene foam. Provision of tilt tension adjustment,upright locking facility and full 360 degree swivel mechanism . The base should be made of crome finnished and fitted with 5 nos twin wheel castor. The pitch centre diameter of the base along with castors should bot exceed 660mm, hydralic height adjustment stoke should be 60-80mm and shall be operated at 30 kg. extension force. Seat & back are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 28-32kg/m3. The backrest has a foam of 28D .The Product should be from the manufacture of approved make of Godrej, Durian, HNI, Herman Miller. complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Cafe Table: Dimension (L)750mm X (D)750mm X (H)750mm. Supplying, and placing in position of cafe table as per image/drawing. The Table top made out of 25mm thk prelam particle board with 2mm thk pvc edge banding with ms powder coated "C" shape legs (50mm x 50mm). Comprising of metal powder coated cross connectors (40mm X 40mm )between legs. . The working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot temperature. The Product should be from the manufacture of approved make of Godrej, Durian, HNI, Herman Miller. complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Cafe Chair: Supplying, and placing in position of cafe chair as per image. size: (l)381mm x (d)419mm x (h)839mm. The seat and back in pvc moulded chair with ss 202 grade frame round pipe. The chair comes in various colours - green, black, red,yellow, blue, brown, orange, white.The Product should be from the manufacture of approved make of Godrej, Durian, HNI, Herman Miller. complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Main Table for DC Cabin/ Ministers office-1,2,3: Main Table Dimension:(L)2800mm X (D)1130mm X (H)770mm Side Runner Dimension: :(L)1200mm X (D)600mm X (H)770mm. Supplying, and placing in position of table as per photograph. This precise Durian Boss's Desk is designed with superb qualityFinish made of engineered wood-medium density fibre board & veneer glossy finish on the same. Functional and stately, with a sturdy design style, this L shape desk is sure to make a dramatic statement in the office. Featuring a cherry finish, with delicate panel moulding and a fantastic size.The modesty frame of the table gives the great look with panel upholstered wth PVC material which gives the leatherette look.Main Table top thkness 80mm , side panel/gable end in 70mm thk mdf with venner glossy finish. Main table and side runner having a skirting @120mm thk with gives a rich look. The office desk comes with the side runner having enough storage space.The side runner top with a thickness of 80mm thk that gives the great look . Side table, side panel, shelves,drawers made up of 18mm thk mdf with venner finish. Table having a provision of Pedestal of size: 400(L) X 500(D) X 660(H) having three drawers to store essential & undestructure made out of 18mm thk mdf with venner finish .Drawers have the stylish handle which enhance the look. Material & Subtype:Engineered Wood - Medium Density Fibre Board, Colour & Colour Family:Red - Cherry.side storage unit having a side panel, one drawer , one shutter & one shelf of 18mm thk mdf with venner finish. The Product should be from the manufacture of approved make of Godrej, Durian, HNI, Herman Miller. complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Back Storage for DC Cabin: Dimension:(L)4200mm X (D)400mm X (H)2000mm Supplying and placing in position of 18mm thick plywood with laminate finish back storage as per image. A well-built bookcase with the looks this is the complete package. A compartmentalized shelving system with adequate space ensures any book will fit in the shelf. This Bookshelf is built using plywood with laminate with 2mm thick PVC edges.. The lower cabinets provide an alcoved space to ensure your books dont yellow with age.The lower area to be provisioned with openable shutters with handles and locking arrangements. The Product should be from the manufacture of approved make of Godrej, Durian, HNI, Herman Millercomplete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Main Chair for DC Cabin: Supplying and placing in position of 360 degrees Revolving High Back chair of size :- (W)673mm X (D)508mm X (H)1270mm ; has soft touch leather, side bolsters and lumbar for maximum support. The chair has resilent wooden base with hard tread Castors.The armrest of the chair is with fixed support on both side for better comfort and support. The armrest shall be in Mahogany wood finish. Provision of soft plush thick padded headrest. Seat and back are made up of 12 - 14 mm thick hot pressed ply wood upholstered with PVC,with polyurethane foam. The chair having multi locking mechanism with soft touch and ergonomically designed seat and back for extra comfort. he chair shall have an single locking center tilt mechanism with 17 degree max. tilt and tilt tension adjustment and full 360 degrees swivel. The one piece arm rest should be made up of solid designer wood and polished with matching colour. The leather patch fixed on wooden arms. The arm rests are fitted to the seat and back with 6mm dia. and 64mm long screw made of HR steel. The prong (base) is made of wooden and fitted with 5nos. twin wheel castors (castor wheel dia. 50mm). The prong (base) is 700mm pitch center dia (740mm with castors). The telescopic bellows is 3 piece telescopic type and injection molded in black polyurethane. The pneumatic height adjustment shall have adjustment stroke of 75mm and shall be operated at 30kgs extension force. The Product should be from the manufacture of approved make of Godrej, Durian, HNI, Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Visitor Chair for DC Cabin: Supplying and placing in position of 360 degrees Revolving Medium Back chair of size :- (W)660mm X (D)508mm X (H)1092mm upholstered with soft touch leather upholstery. The ultra soft cushions , side bolsters and lumbar bolsters for maximum support. The chair shall be provisioned with extra padded wooden mahagony handles for comfort.Provision of soft touch leather upholstery and ultra soft cushions. The chair has wooden base with hard tread Castors. The Seat and back are made up of 14 mm thick hot pressed ply wood upholstered with PVC,with polyurethane foam. The chair having soft touch and ergonomically designed seat and back for extra comfort. Chair seat has foam of density 45 (+/-2kg /m3) . The backrest has a foam of 28 (+/-2kg /m3). The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Sofa for DC Cabin/Ante Room: 3 seater Dimension(L)2125mm X (D)960mm X (H)820mm Supplying, and placing in position of sofa as per Image. The Sofa stands firm on solid pvc legs with thick armrests that are slightly curved on the front face of the sofa. Each curve defines a seating space which provides for people to be seated comfortably. Finished in a eerie black premium leatherette, the sofa makes a fantastic first impression. The cushioning adds supreme comfort for the person sitting on it making this a must have in every living space. Material & subtype:Premium Leatherette, Colour & Colour Family, Black - Eerie Black, Seating Height:18.70", Legs:Wooden, Finish:Matte, Size:Standard, Style:Contemporary.The seat cushion is made of multi layered foam of density 32-35kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. The polyster polyfill keeps the upholstery wrinke free & soft.The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller. complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

2 seaterDimension (L)1600mm X (D)960mm X (H)820mm

1 seater Dimension(L)1140mm X (D)960mm X (H)820mm

Meeting Table for DC Cabin/Ante Room: Dimension:Dia 900mm x 750mm(H) Supplying, and placing in position of meeting round table of size: Dia 900mm x 750mm(H) as per image/drawing . The table made out of 25mm thk Prelam Particle board with 2mm thk Pvc edge banding.Table top supported with MS powder coated pole.The Product should be from the manufacture of approved make of Godrej, Durian, HNI, Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Meeting Chair for DC Cabin/Ante Room: Supplying and placing in position of 360 degrees Revolving Medium Back chair of size :- (W)660mm X (D)510mm X (H)1060mmas per image. The backrest is fitted with taut breathable mesh for optimal support with an adjustable lower back support. The seat cushion stays firm on the sleek chrome base with sturdy nylon castors. Upholstered in soft black fabric the seat cushions comfort. Powered by a pneumatic gas lift and tilt tension control the chair offers superb ergonomic support for your body. Mechanism:Tilt Tension Control, Adjustable Armrest..The pneumatic height adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs extension force. The Seat are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3. The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Conference Table Dimension: 9900mm(L) x 2200mm(D) x 750mm(H) Supplying, and placing in position of conferrence table as per photograph/drawing . The worksurface top should be of thickness 42mm top prelam particle board . The side panel made up of 36mm thk prelam particle board with 2mm thk pvc edge banding & modesty panel made out of 25mm thk prelam particle board with 2mm thk pvc edge banding. The legs of the table should be Made from 36mm prelam prelam board with edge banding . The wire carrier should Made from 0.6mm thick CRCA & powder coated 40-50 microns . Also provision of flip top box & metal raceway for wire flow.The Product should be from the manufacture of approved make of Godrej, Durian, HNI, Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Conference Main Chair: Supplying, and placing in position of 360 degree revloving high back chair as per Image. The high mesh back chair is a magnificient chair with creative tree detailing, so when you look at it from afar it feels as if a tree is emerging from the roots to the branches and leaves on the top. The leaves add function to the design being adjustable for improved lumbar support. The chair with adjustable headrest & armrests. Material & Subtype: Mesh, Colour & Colour Family: Black, Dimension(W)600mm X (D)500mm X (H)1282mm, Back Type:high Back, Base:Aluminium Base, Base Type:Revolving, Maximum Seating Height:21.25" ,Minimum Seat Height:17.32", Function: Revolving::Pneumatic Height Lift::Adjustable :Multi-Locking Knee Tilt::Adjustable Armrest, 3 D Lumbar Support,Locking Mechanism: self tention adjustment/any position multi locking, chair Handle: adjustable handle with pp pad . The Seat are made up of 12mm thk hot pressed plywood upholstered with moulded foam and fabric, chair seat has foam of density 32-35 kg/m3. .The Product should be from the manufacture of approved make of Godrej, Durian, HNI, Herman Miller. complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Conference Visitor Chair, Supplying, and placing in position of 360 degree revloving medium back chair as per Image. The medium mesh back chair is a magnificient chair with creative tree detailing, so when you look at it from afar it feels as if a tree is emerging from the roots to the branches and leaves on the top. The leaves add function to the design being adjustable for improved lumbar support. The chair with adjustable armrests.Material & Subtype: Mesh, Colour & Colour Family: Black, Dimension(W)600mm X (D)500mm X (H)1090mm, Back Type:Medium Back, Base:Aluminium Base, Base Type:Revolving, Maximum Seating Height:21.25" ,Minimum Seat Height:17.32", Function: Revolving::Pneumatic Height Lift::Adjustable :Multi-Locking Knee Tilt::Adjustable, Armrest, 3 D Lumbar Support,Locking Mechanism: self tention adjustment/any position multi locking, chair Handle: adjustable handle with pp pad. The Seat are made up of 12mm thk hot pressed plywood upholstered with moulded foam and fabric, chair seat has foam of density 32-35 kg/m3. .The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Main Table for IAS officer: Main Table Dimension:(L)2400mm X (D)1130mm X (H)770mm Side Runner Dimension: :(L)1200mm X (D)600mm X (H)770mm Supplying, and placing in position of table as per photograph. This precise Durian Boss's Desk is designed with superb qualityFinish made of engineered wood-medium density fibre board & veneer glossy finish on the same. Functional and stately, with a sturdy design style, this L shape desk is sure to make a dramatic statement in the office. Featuring a cherry finish, with delicate panel moulding and a fantastic size.The modesty frame of the table gives the great look with panel upholstered wth PVC material which gives the leatherette look.Main Table top thkness 80mm , side panel/gable end in 70mm thk mdf with venner glossy finish. Main table and side runner having a skirting @120mm thk with gives a rich look. The office desk comes with the side runner having enough storage space.The side runner top with a thickness of 80mm thk that gives the great look . Side table, side panel, shelves,drawers made up of 18mm thk mdf with venner finish. Table having a provision of Pedestal of size: 400(L) X 500(D) X 660(H) having three drawers to store essential & undestructure made out of 18mm thk mdf with venner finish .Drawers have the stylish handle which enhance the look. Material & Subtype:Engineered Wood - Medium Density Fibre Board, Colour & Colour Family:Red - Cherry.side storage unit having a side panel, one drawer , one shutter & one shelf of 18mm thk mdf with venner finish. The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Back Storage for IAS officer: Dimension:(L)3800mm X (D)400mm X (H)2000mm Supplying and placing in position of 18mm thick plywood with laminate finish back storage as per image. A well-built bookcase with the looks this is the complete package. A compartmentalized shelving system with adequate space ensures any book will fit in the shelf. This Bookshelf is built using plywood with laminate with 2mm thick PVC edges.. The lower cabinets provide an alcoved space to ensure your books dont yellow with age.The lower area to be provisioned with openable shutters with handles and locking arrangements. The upper area to have open shelves for display. The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Main Chair for IAS officer: Supplying, and placing in position of 360 degree revloving high back chair as per Image.The premium upholstery is an added touch of extra class. With its supple leather upholstery. Equipped with a multi-locking knee tilt mechanism and adjustable arms this chair is is high on back support and comfort.Size: (W)610mm X (D)500mm X (H)1300mm, Material: Leather: Semi Aniline Leather, Function: Revolving::Pneumatic Height Lift::Adjustable Armrest::Multilocking Knee Tilt, Maximum Seating Height: 24",Minimum Seat Height: 20.86", Base :Chrome Base, Locking Mechanism: Multi-Locking Knee Tilt. The Seat & back are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-25 kg/m3.The backrest has a foam of 28D. The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Visitor Chair for IAS officer: Supplying, and placing in position of 360 degree revloving medium back chair as per Image. The premium upholstery is an added touch of extra class. With its supple leather upholstery. Equipped with a multi-locking knee tilt mechanism and adjustable arms this chair is is high on back support and comfort.t.Dimension (W)640mm X (D)500mm X (H)1130mm, Material:Leather: Semi Aniline Leather, Function: Revolving::Pneumatic Height Lift::Adjustable Armrest::Multilocking Knee Tilt, Maximum Seating Height: 24",Minimum Seat Height: 20.86", Base :Chrome Base, Locking Mechanism: Multi-Locking Knee Tilt. The Seat & back are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-25 kg/m3.The backrest has a foam of 28D. The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Sofa for IAS officer: 3 seater Dimension(L)2125mm X (D)960mm X (H)820mm Supplying, and placing in position of sofa as per Image. The Sofa stands firm on solid pvc legs with thick armrests that are slightly curved on the front face of the sofa. Each curve defines a seating space which provides for people to be seated comfortably. Finished in a eerie black premium leatherette, the sofa makes a fantastic first impression. The cushioning adds supreme comfort for the person sitting on it making this a must have in every living space. Material & subtype:Premium Leatherette, Colour & Colour Family, Black - Eerie Black, Seating Height:18.70", Legs:Wooden, Finish:Matte, Size:Standard, Style:Contemporary.The seat cushion is made of multi layered foam of density 32-35kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. The polyster polyfill keeps the upholstery wrinke free & soft.The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

2 seaterDimension (L)1600mm X (D)960mm X (H)820mm

Centre Table for IAS officer: Dimension:(L)1130mm X (W)630mm X (H)410mm. Supplying and placing in position of centre table as per photograph. The centre table made of solid wood (steam beech) in pu matt polish.The plain glass placed the top of the table in 8mm thk. The turned wooden legs are sleek and sturdy providing the table with its support. The wood work below the glass provides the glass with a focal point and some support. Add volumes of style to yourliving room with the centre table. Material & subtype: Solid Wood -Beech Wood( spc:steam beach), Colour & Colour Family:Brown - Dark Oak,Shape:Rectangular Legs/Base:Solid Wood, Finish:Glossy,Style:Contemporary.The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Meeting Table: Dimension:1500mm dia. x 750mm(H) Supplying and placing in position of Round Meeting table as per photograph. Table on ground having capacity of 8 seats overall size 1500mm dia. x 750mmH. Table top shall be made out of 25mm thick prelam particle board of approved shades. The table top shall be supported on 18mm thick understructure made with prelam particle board with pvc edges.. The working or nonworking edges shall be provided with matching machine pressed 2mm thick PVC edging using with special hot melt glue at hot temperature.The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Meeting Chair: Supplying and placing in position of 360 degrees Revolving Medium Back chair of size :- (W)660mm X (D)510mm X (H)1060mmas per image. The backrest is fitted with taut breathable mesh for optimal support with an adjustable lower back support. The seat cushion stays firm on the sleek chrome base with sturdy nylon castors. Upholstered in soft black fabric the seat cushions comfort. Powered by a pneumatic gas lift and tilt tension control the chair offers superb ergonomic support for your body. Mechanism:Tilt Tension Control, Adjustable Armrest..The pneumatic height adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs extension force. The Seat are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3. .The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Main Table for Middle officers/ Junior Officer: Main Table Dimension : 2000mm(L) X 900mm(d) x 755mm(h) all over Side Runner Dimension: 1800mm(L) X 500mm(d) x 660mm(h) Supplying and placing in position of Table as per photograph. This precise Boss's Desk of size :- (L)2000mm X (D)1800mm X (H)755mm is designed with superb quality. The table shall be made with a combination of engineered wood as particle board, this gorgeous desk has contrasting panels in black for a contemporary look.The table top of 2000mm length x 900mm depth and 45mm thickness shall be Coupled with a runner and storage of size :- L-1800mm x D-450mm x H-660mm for your files and cabinets. The overall side storage shall be made with 18mm thick particle board finished with 2mm thick PVC edge banding of matching shade.The side storage shall be provisioned with openable shutter storage, 3 drawers (2 equal drawers+ 1 filing drawer) pedestal and open storage with handles and locking arrangement. The table shall also be provisioned with a pedestal at opposite side of storage. The pedestal shall be with a combination of 2 drawers and 1 filing drawer. With a warm walnut finish, the dual tone finish of the desk adds to its overall style and finish.The font side of the table shall have design element finished in leatherite. .The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Back Storage for Middle officers/ Junior Officer: Dimension: (L)4000mm X (D)450mm X (H)750mm Supplying , and placing in position of back storage as per photograph/drawing. The complete storage unit shall be made up of 18 mm thick prelam particle board with 2mm thk pvc edge banding . The storage shall be provisioned with one shelf and 2 nos compartments .The storage shall have openable shutters with handles and locking arrangements.All working or non working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot temperature. The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Main chair for Middle officers/ Junior Officer: Supplying, and placing in position of 360 degree revloving high back chair as per Image. The high mesh back chair is a magnificient chair with creative tree detailing, so when you look at it from afar it feels as if a tree is emerging from the roots to the branches and leaves on the top. The leaves add function to the design being adjustable for improved lumbar support. The chair with adjustable headrest & armrests. Material & Subtype: Mesh, Colour & Colour Family: Black, Dimension(W)600mm X (D)500mm X (H)1282mm, Back Type:high Back, Base:Aluminium Base, Base Type:Revolving, Maximum Seating Height:21.25" ,Minimum Seat Height:17.32", Function: Revolving::Pneumatic Height Lift::Adjustable :Multi-Locking Knee Tilt::Adjustable Armrest, 3 D Lumbar Support,Locking Mechanism: self tention adjustment/any position multi locking, chair Handle: adjustable handle with pp pad . The Seat are made up of 12mm thk hot pressed plywood upholstered with moulded foam and fabric, chair seat has foam of density 32-35 kg/m3.The Product should be from the manufacture of approved make of Godrej, Durian, HNI, Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge

Visitor Chair for Middle officers/ Junior Officer Supplying, and placing in position of 360 degree revloving medium back chair as per Image. The medium mesh back chair is a magnificient chair with creative tree detailing, so when you look at it from afar it feels as if a tree is emerging from the roots to the branches and leaves on the top. The leaves add function to the design being adjustable for improved lumbar support. The chair with adjustable armrests.Material & Subtype: Mesh, Colour & Colour Family: Black, Dimension(W)600mm X (D)500mm X (H)1090mm, Back Type:Medium Back, Base:Aluminium Base, Base Type:Revolving, Maximum Seating Height:21.25" ,Minimum Seat Height:17.32", Function: Revolving::Pneumatic Height Lift::Adjustable :Multi-Locking Knee Tilt::Adjustable, Armrest, 3 D Lumbar Support,Locking Mechanism: self tention adjustment/any position multi locking, chair Handle: adjustable handle with pp pad . The Seat are made up of 12mm thk hot pressed plywood upholstered with moulded foam and fabric, chair seat has foam of density 32-35 kg/m3. The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Sofa for Middle officers/ Junior Officer: 3 seater Dimension (L)1905mm X (D)890mm X (H)870mm Supplying, and placing in position of sofa as per Image .classic Contemporary design and slender curves. . The Sofa of stands Firm on solid PVC legs with thick armrests that are slightly curved on the front face of the sofa. Each curve defines a seating space which provides for people to be seated comfortably. Finished in a Brown Nappa Aire Leather, the sofa makes a fantastic first impression. The Cushioning is molded such that it flows along the partition for a clean unified look. steam beech solid wood have used for framing construction of sofa The seat cushion is made of multi layered foam of density 32-35kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. The polyster polyfill keeps the upholstery wrinke free & soft. The Product should be from the manufacture of approved make of Godrej, Durian, HNI Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

2 seater Dimension (L)1410mm X (D)890mm X (H)870mm

Side Table for Middle officers/ Junior Officer: Dimension (L)680mm X (W)530mm X (H)460mm Supplying, and placing in position of side table as per photograph.The glass table top is made with strong glass and is inlaid onto the solid wood frame. The designer wooden legs are turned for a sleeker look. The framed edges slope inwards to the table top with defined edges. Material & subtype: Solid Wood - Beech Wood, Colour & Colour Family Brown - Dark Oak, Shape: Rectangular, Dimension (L)680mm X (W)530mm X (H)460mm, Legs :Solid Wood,Finish Glossy.The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller. complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Computer Table for Middle officers/ Junior Officer: Dimension: 1200mm(L) X 600mm(D) X 750mm(H) Supplying, and placing in position of Free standing table as per Image/drawing. The table top made up of 25mm thick pre-laminated particle board with 2mm thk pvc edge banding . The Table supported with 18mm thk Prelam Particle board side panel & Modesty panel. The working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot temperature. Provision of one fixed Pedestal storage unit (combination of two drawers and one filing drawer) . Pedstal Unit made of 18mm thk prelaminated particle board with 2mm thk pvc edge banding..Also having a provision of pvc keyboard tray & metal cpu trolley.The Product should be from the manufacture of approved make of Godrej, Durian, HNI, Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Computer Chair for Middle officers/ Junior Officer Supplying, and placing in position of 360 degree revloving medium back chair as per Image. The medium mesh back chair is a magnificient chair with creative tree detailing, so when you look at it from afar it feels as if a tree is emerging from the roots to the branches and leaves on the top. The leaves add function to the design being adjustable for improved lumbar support. The chair with adjustable armrests.Material & Subtype: Mesh, Colour & Colour Family: Black, Dimension(W)600mm X (D)500mm X (H)1090mm, Back Type:Medium Back, Base:Aluminium Base, Base Type:Revolving, Maximum Seating Height:21.25" ,Minimum Seat Height:17.32", Function: Revolving::Pneumatic Height Lift::Adjustable :Multi-Locking Knee Tilt::Adjustable, Armrest, 3 D Lumbar Support,Locking Mechanism: self tention adjustment/any position multi locking, chair Handle: adjustable handle with pp pad . The Seat are made up of 12mm thk hot pressed plywood upholstered with moulded foam and fabric, chair seat has foam of density 32-35 kg/m3. The Product should be from the manufacture of approved make of Godrej, Durian, HNI, Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge

Dimension: 650mm (L) x 460mm(D) x1000mm(H) Supplying, and placing in position of auditorium chair as per photograph. linear lines and smart design togethermakes stellar. It is sturdy,stylish and absolutely comfortable. The best part about stellar is its push back feature, that suppots your spine while easing the tension in your back:Features:100 % polyester stretch fabric, bonded with 3mm/5mm/7.5 mm foam as required with net backing, Seat density: High Density premium molded foam of density 50 kg/m2, +/-5 configuation: 480 x 490 x 19mm of 19mm plywood of ISI 303. Back density of 48 kg/m2 +/-5 Configuation: 470 xd 130 x 640 to 770mm of 15mm moulded plywood. Mechanism: Push back , Wings: Metal stand of 200x 75 x 6mm M.S flat Armrest option: Cupholder- large & Small, wood flat arm rest, wood waterfall arm rest. Base frame: MS/Sturdy steel frame of size 450 x 440 x 1.6mm.The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Sofa for Waiting area/VIP Waiting lounge: Dimension:(L)1130mm X (W)630mm X (H)410mm Supplying, and placing in position of sofa as per Image.A supple premium Leatherette upholstery adds class to the soft cushioned backrest and seating. Sitting proudly on sleek steel legs the sofa exudes a sense of comfort that is perfect for any space. Material & subtype:Premium Leatherette, Colour & Colour Family:Brown-Camel Brown, Seating Height:16.14" ,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern, Texture:Two Tone. steam beech solid wood have used for framing construction of sofa .The seat cushion is made of multi layered foam of density 32-35 kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. The polyster polyfill keeps the upholstery wrinke free & soft.The Product should be from the manufacture of approved make of Godrej, Durian, HNI,Herman Miller complete as per specification mentioned above & images under the guidence of project architect & engineer incharge.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 1.1.1: GROUP A

1.1.2: GROUP B

1.1.3: GROUP C

Wiring for multi control light point limiting to 200W point with 3x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system with 20mm dia rigid ISI marked Steel conduit pipe including 15/16 Amp flush type switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) with phenolic laminated sheet cover ,ceiling rose etc. complete 1.1: Short point up to 3.00 metre. length.

1.2: Medium point up to 6.00 metre. Length.

1.3: Long point up to 10.00 metre. Length.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required 1.7.1: With 2 x 1.5 sq. mm.

1.7.2: 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 1.7.7: 4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire

1.7.8: 4 X 4 sq. mm + 2 X 4 sq. mm earth wire

1.7.9: 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

1.7.10: 4 X 10 sq. mm + 2 X 6 sq. mm earth wire

1.7.11: 4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 1.14.2: 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.7: 4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying including fitting and fixing of following front plate of suitable colour MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE as per direction of department. 1.1: 1 module

2 module

3 module

4 module

5 module

6 module

8 module

10 module

16 module

24 module

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1.27.1: 1-2 module type Metal

3 module type Metal

4-5 module type Metal

6-8 module type Metal

12-16 module type Metal

10 module type Metal

24 module type Metal

Wiring to a 5 pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel or Equivalent Make as approved by the Deptt.) in surface/ recessed ISI marked Steel 20 mm. dia. conduit pipe wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete. 5.1: Short point up to 3.00 metre. length.

Medium point up to 6.00 metre. Length.

Long point up to 10.00 metre. Length.

Supplying including installation of socket outlet 6 Amps 3 pin combine shuttered complete , MODEL RANGE LEGRAND (MYLINC), ANCHOR (ROMA), MK (IVORY), ABB (CLASSIC), KOLORS (KRAZE), SCHNEIDER (OPAL), PHILIPS, Havells including making necessary connection as per direction of department.

Supplying with fitting and fixing of 6 amp one way modular clip in switch, MODEL RANGE LEGRAND (MYLINC), ANCHOR (ROMA), MK (IVORY), ABB (CLASSIC), KOLORS (KRAZE), SCHNEIDER (OPAL), PHILIPS, Havells including making necessary connection as per direction of department.

Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system including earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20 mm. dia.Steel conduit (AKG or equivalent as approved by the Deptt.) 8.1: Short point up to 3.00 metre. length.

Medium point up to 6.00 metre. Length.

Long point up to 10.00 metre. Length.

Supplying including installation of socket outlet 10/16 Amps 3/5 pin combine shuttered complete , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting and fixing of 16 amp one way modular clip in switch WITH LED, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLANZE), SCHNEIDER (ZENSELO) including making necessary connection as per direction of department.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, missioning etc. as required. 1.50.2: 510 mm sweep

Extra for fixing the Louvers/Shutters complete with frame for exhaust fans of all sizes

DISTRIBUTION BOARD: Supplying with fitting and fixing panel mounting open execution 25KA 415V 50Hz 4P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 25 KA 415V 50 Hz 4P MCCB (Schneider, legrand, Siemens, Indo Asian make) 11.1: 40A

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 2.3.1: 6 way SPN double door

2.3.3: 8 way SPN double door

2.3.4: 12 way SPN double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator . 2.4.1: 4way (8+12+12) double door

2.4.2: 6way (8+12+18) double door

2.4.3: 8way (8+12+24) double door

12way (8+12+36) double door

Supplying with fitting and fixing MCCB incomer and MCB outgoing sheet steel, phosphatised, powder painted single door surface mounting vertical TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar up to 125A and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 13.1: 4 way TPN (4+12) single door

13.2: 8 way TPN (4+24) single door

13.3: 12 way TPN (4+36) single door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.10.1: SINGLE POLE

2.10.3: DOUBLE POLE

Supplying with fitting and fixing 4P 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C Series (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 16.1: 40A

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.12.1: 40 A

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.13.1: 40 A

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.14.1: 25A

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand)including trenching (75 cm deep) and refilling etc as required. 14.13.1: 50 mm dia

14.13.2: 80 mm dia

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 14.15.1: 63 mm dia (OD-63 mm & ID-51 mm nominal)

14.15.5: 200 mm dia (OD-200 mm & ID-175 mm nominal)

Supply and making of the following sizes of Brick masonary Manholes & Cable trench from class-A brick complete with 40mm thick PCC (1:4:8) base, plastering with 8 mm thick (1:6) cement mortar with cement coat of inside of the trench, including providing of prefabricated 75 mm thick RCC cover with corner of the cover protected with ISA 35, complete with excavation & removal of surplus soil. i) 600mm (W) x 1000mm (D) trench

ii): 900mm (W) x 900mm (D) trench

iii): 750mm x 750mm x 1000mm deep Manhole

iv): 450mm x 450mm x 600mm deep Manhole

Providing and laying 1.6 mm thick pregalvanized GI factory fabricated raceways of the following sizes including 3 mm thick GI covers, providing knock out holes and all required fixing accessories including 6 SWG GI earth wire complete as required including floor /wall supports, bends, access boxes and tap off boxes as per specification and cross over as per site requirement. Note:- Blue & Orange colour shall be considered for Power & Data raceway respectively. The item shall include the cost of chipping, cutting the floor for laying the raceway and making good the finish including chicken mesh complete as required as per site requirement. NS: 100 mm wide x 40 mm deep raceway

200 mm wide x 40 mm deep raceway

300 mm wide x 40 mm deep raceway

Providing and fixing of 350 x 350 x 50 mm deep (Nominal size) floor junction box including providing 3 mm thick GI cover required as per specification

Providing and fixing of 250 x 250 x 50 mm deep (Nominal size) floor junction box including providing 3 mm thick GI cover required as per specification

Providing and fixing of 150 x 150 x 50 mm deep (Nominal size) floor junction box including providing 3 mm thick GI cover required as per specification

CABLE TRAY: Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts. Size of Tray 4.1.2: 150

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 4.2.2: 150

NS: Inter/Exter Bend NS.1: 150

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 4.3.2: 150

Supply, Unloading, Receiving, Storing, Assembling, Fixing, Testing and Commissioning of the following lighting fixtures with all fitting, driver, housing & reflector complete with providing of all necessary hardware’s like raw plugs, hangers, support plates and connection wire in flexible GI pipe from point to light terminal as required for fixing etc. as required. Complete in all respect. All toll & tackles required for successful installation, testing & commissioning shall be in scope of installer. 15.3: Supplying,installation,testing and commissioning of Microwave technology based occupancy sensor having high preformance, non regulating programmable type, suitable for connected load upto 10Amp , for mounting height up to 2.6 mtr and for 5m X 20m coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required.

Supply, installation, testing & commissioning of Recess Mounted Linear Led Fixture consuming a system wattage of 30W (±10%) & the luminaire shall be with system efficacy ≥ 110lm/W. Housing: CRCA/Extr . IP20 , Optics: PMMA/Polysterene Diffuser. The operating CCT shall be 5700K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Wipro Cat No.: LM30-401XXX-57G1CT

Supply, installation, testing & commissioning of 4ft Linear LED luminaire delivering an initial system lumen of 2000 lumens & the luminaire shall be with system efficacy ≥ 100 lm / W. The luminaire Housing shall be made of PC & the diffuser shall be of polycarbonate/PMMA. The operating CCT shall be 6500K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 20% & PF ≥ 0.95 , 50,000 Hrs LED Life with L70 Criteria, IP20. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Wipro Cat No.: LL20-221-XXX-65-NE3

Supply, installation, testing & commissioning of 18W Recess mounted Round Led Downlighter delivering an initial system lumen of 1527 lumens & the luminaire shall be with system efficacy ≥ 80 lm / W. Housing: Die Cast Aluminium. IP20 , Optics: PMMA LGP/Polysterene Diffuser. The operating CCT shall be 6000K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 20% & PF ≥ 0.95, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Wipro Cat No.: LD80-171-XXX-60-XX

Supply, installation, testing & commissioning of Recess mounted LED 2'x2' luminaire delivering an initial system lumen of 3600 lumens & the luminaire shall be with system efficacy ≥ 100 lm / W. Housing: CRCA, Rim: Engneering plastic/CRCA. Optics: polycarbonate/PMMA/Polysterene, IP20 Protection. The operating CCT shall be 5700K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.95, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Wipro Cat No.: CRCO10R038HP57GL1

Supply, installation, testing & commissioning of Bulk Head Luminare delivering an initial system lumen of 1000 lumens & the luminaire shall be with system efficacy ≥ 100 lm / W. Housing: Die Cast Aluminium. IP65 , Diffuser : OPAL Polycarbonate, IK 07. The operating CCT shall be 5700K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.95, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Wipro Cat No.: LW07-141-XXX-57-G1

Supply, installation, testing & commissioning of Surface mounted Square Led Downlighter delivering an initial system lumen of 1527 lumens & the luminaire shall be with system efficacy ≥ 80 lm / W. Housing: Die Cast Aluminium. IP20 , Optics: PMMA LGP/Polysterene Diffuser. The operating CCT shall be 6000K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 20% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Wipro Cat No.: LD81-171-XXX-60-SM

Supply, installation, testing & commissioning of 2ft Linear LED luminaire delivering an initial system lumen of 903 lumens & the luminaire shall be with system efficacy ≥ 90 lm / W. The luminaire Housing shall be made of PC & the diffuser shall be of polycarbonate/PMMA. The operating CCT shall be 6500K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 20% & PF ≥ 0.95 , 50,000 Hrs LED Life with L70 Criteria, IP20. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Wipro Cat No.: LL20-111-XXX-65-NE3

Supply, installation, testing & commissioning of 12W Recessed mounted Round Led Downlighter delivering an initial system lumen of 998 lumens & the luminaire shall be with system efficacy ≥ 80 lm / W. Housing: Die Cast Aluminium. IP20 , Optics: PMMA LGP/Polysterene Diffuser. The operating CCT shall be 6000K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 20% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacturer along with Photo Biological Safety Standard. Wipro Cat No.: LD80-101-XXX-60-XX

Supplying including fitting and fixing of following A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt. as required complete and as directed by the Department [ without regulator]. Premium model 1200 mm Sweep (ORIENT PSPO make) / Premium model 1050 / 1200 mm Sweep SS-390 Deco (Havells make)

Supplying including fitting and fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt. as required complete and as directed by the Department. Heavy Duty 450 mm sweep 900 RPM Single phase (ORIENT make)

LED light fixture Wipro make- Bracket Light with holder or equivalent.

Sign Boards: Supply, Unloading, Receiving, Storing, Assembling, Fixing, Testing and Commissioning of Single sided exit sign board for wall / ceiling / pendant cantilever mounting, with white housing, Red stencil & Battery backup capability and dual power supply (AC/DC) and push to test switch for mandated code compliance testing, including long life SMF rechargeable Ni Cd battery and internal solid-state transfer switch automatically connects the internal battery to LED board for minimum 90 minute emergency illumination. Fully automatic solid-state, two-rate charger initiates battery charging to recharge a discharged battery in 24 hours. Complete in all respect.

Same as above but two sided sign board.

Note:- Sign Board to comply with UL924, NFPA 101 Life Safety Code, NEC, OSHA, Local and State Codes and UL listed for damp locations. (0°C – 50°C) Aviation Obstruction light with Light Emitting Diods. Supply Unloading, Receiving, Storing, Assembling, Fixing, Testing and Commissioning of the following lighting fixtures with all fitting, driver, housing & reflector complete with providing of all necessary hardares like raw plugs, hangers, support plates and connection wire in flexible GI pipe. Aviation obstruction light with Light Emitting Diods (LEDs). Complete with control panel and all accessories as per specifications. 6 Mtr. high GI pipe fabrication support structure providing with suitable base plate, with inline coupling, guying system complete as required, clamping system, termination arrangement. Lights to operates on 240V, single phase A.C (50Hz). The lights shall be supplied with intensity step changer including all accessories, lighting to be at 2500cd, Louvers to be provided to all lights to avoid dazzle to aircraft and local residents. Unit shall comprise: •Cap holder, •Polycarbonate cap, •Internal reflector, •IP66 glad plates on lights, •Flash Head Assembly (20 flashes per minute): Contractor to agree with Surat Civil Aviation Authority. •Flash head control unit. •Integral adjustable tilt angle mounting bracket for flash head assembly. •Intelligent lamp control technology for maximum lamp life (MTBF 50,000 to 100,000h). Operating Conditions: •Suitable for temperatures ranging from -30°C to +55°C., •Suitable for wind, fog and rain., •Humidity : up to 100% •Control Panel for Aviation Lighting to provide -, 1) Night mode light intensity adjustment. 2) Provide flash synchronization for up to 20 flash heads., 3) Built in Surge Protection, 4) IP- 54 degree of Ingress protection., 5) Colour shall be RED., 6) Power factor shall be leading power factor. NS: •Requirements of wiring material and details shall be clearly mentioned by tenderer and the same shall be as per Civil Aviation department.

Carriage of Ceiling fans/ exhaust and regulator from store to site as required within 30-km radius.

Installation of Exhaust fan up to 450 mm sweep in the existing opening including making the hole to suit the size of the above fan, making good the damages, testing, commissioning etc. as required complete

UPS / INVERTER WORK: Ratings of the UPS as follows :- Supply, installation, testing and commissioning of 2 x 160 kVA UPS in parallel redundant N+N configuration, 3 phase (415 V + 15%) Volts input & 3 phase output (415 V + 1%), 50 Hz, Input harmonic Current THD 3% typical at 100% load, 6% maximum at 50% load and 30 min battery backup for each UPS along with battery cabinet complete in all respect including supporting steel structure for UPS and Battery as required. Quoted price shall be inclusive of approved rating single core copper conductor cable connecting UPS and batteries.

Supply, installation, testing and commissioning of 20 kVA UPS 3 phase (415 V + 15%) Volts input & 3 phase output (415 V + 1%), 50 Hz, Input harmonic Current THD 3% typical at 100% load, 6% maximum at 50% load and 30 min battery backup for each UPS along with battery cabinet complete in all respect including supporting steel structure for UPS and Battery as required. Quoted price shall be inclusive of approved rating single core copper conductor cable connecting UPS and batteries.

"Supply, installation, testing & commissioning of rating Invertors 1-phase IN, 1-phase OUT complete as required & troly and as per following specification: Input: AC Voltage : 220V (-20% + 20%), Phase : - 1-phase, Frequency : 50Hz, +/- 3Hz." Output: AC Voltage : 230 V, ± 10%, Phase : Single, Frequency : 50 Hz, ± 0.05%, Output Wave Form : Pure Sine Wave., Output Wave form distortion : Less than 1%. Test report should be provided for the same. Transient Response : 0-100% step load, change in output voltage is 10 V and recover back within 10 cycles. Rated Power Factor : 0.8 Overload Capacity : 120% for 10 minutes. 120% for 10 minutes. : 150% for 60 seconds. Cooling System : Forced Air (In-built) Battery Charger Type: Recharge Time : Automatic boost cum float charging for enhanced life. Back-up Type of Batteries : 30 minutes, Audio Alarm : Warning Buzzer for battery low. Indications : Mains ON, Charger ON, Inverter ON, Battery LOW, Inverter OVERLOAD. Protections: AC input : SP MCB, DC fuse : Fuse in Battery Path, Output under voltage : Inverter Trips, Protection : Inverter Trips, Output overload : Current Limit, Protection : Both on Charger & Inverter, Short circuit : For Overload, Trip Facility : For Battery Low, :For Output Over Voltage. Control & User Connection: Input through : 3 way terminal 3 core cable, Output through : 32 Amps output socket / terminal Battery connection : 2 way terminal Inverter ON/OFF : Rocker switch Environmental: Ambient Temperature : 0 to 50OC, Humidity : 20 to 90% non condensing, Noise Level : < 200 dB Output capacity as follows: 1000VA Capacity

SERVER, DATA & VOICE NETWORKING: Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 1.18.2: 2 Pair

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supply and fixing of 25 mm dia 1.50mm to 2.00mm average wall thickness heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) on surface system including painting etc as required:

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Supplying with fitting and fixing of RJ-11 Telephone jack , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying including fitting and fixing of TV co-axial outlet MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department.

Supplying including fitting and fixing of following Metal boxes for MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE in surface/ recessed system complete as per direction of department. 1-2 module type Metal

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 1.53.1: 1 run of cable

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1.53.1: 1 run of cable

2 run of cable

3 run of cable

Supplying & Fixing of Non- PCB based Information Outlet (I/O) RJ45, Tolless Termination TIA-568C Category-6, Termination of Catergory-6 UTP Cable, UL listed ,Shall conform to Category-6 as per the EIA/TIA-568C.2,Shall support network line speeds up to 1 Gbps, Shall have RJ-45 type connector with bend limiting and strain relief boot for securing IDC contacts from external forces and for maintaining the bend radius of the cable, Shall have minimum duraility of 950 or Above mating cycles and 200 termination cycles. Certified by independent labs like ETL/GHMT/3P for compliance to EIA/TIA-568C.2 complete in all respect.. Make-Siemon/Panduit/Legrand

Supplying & Fixing of Single Faceplate Shall be Duplex Port (RJ45) square plate, dimension as per commercially available modular office furniture.Shall have spring shuttered front access for preventing ingress of dust,Shall be supplied with Gang Box of the same size by System Integrator complete in all respect. . Make-Siemon/Panduit/Legrand

Supplying & Fixing of UTP Jack Panel, loaded with 24 nos UTP ports for Non-PCB based IO Jacks (RJ45, TIA-568C Category-6, Shall have integrated bonding bar or other mechanism for grounding, Shall be loaded with individually replaceable 24 nos. Category-6 certification by Jacks complying with TIA-568.C.2 , Shall be having a 6 port module construction for better cable dressing at the rear, the jacks shall have RJ-45 type connector with bend limiting and strain relief boot for securing IDC contacts from external forces and for maintaining the bend radius of the cable complete in all respect. . Make-Siemon/Panduit/Legrand

Supplying of 4-pair Unshielded twisted pair with a cross filler (+), meeting Category 6 standards as per TIA-568C.2, The cable should be tested till 250 MHz , Shall be Fire-Retardant, Low-Smoke & Zero-Halogen as per IEC 60332-1, IEC 61034-2 & IEC 60754-1 respectively. Make-Siemon/Panduit/Legrand

Supplying & Fixing of Category 6, UTP patch cords shall be constructed of 24-27 AWG unshielded twisted pair stranded copper cable with an enhanced performance modular plug at each end. Patch cord cable shall be offered in multiple colored UTP cable for design flexibility with a clear strain relief boot on each modular plug. All patch cords shall be compatible with both T568A and T568B wiring schemes. UTP Cable will be 1.0 mtr. complete in all respect. Jacket - LSZH . Make-Siemon/Panduit/Legrand

Supplying & Fixing of Category 6 UTP patch cords shall be constructed of 24-27 AWG unshielded twisted pair stranded copper cable with an enhanced performance modular plug at each end. Patch cord cable shall be offered in multiple colored UTP cable for design flexibility with a clear strain relief boot on each modular plug. All patch cords shall be compatible with both T568A and T568B wiring schemes. Blue UTP Cable, 2 Meter complete in all respect. Jacket -LSZH . Make-Siemon/Panduit/Legrand

Supplying & Fixing of Fiber Optic LC style fully loaded Patch Panel (FOPP), 19" Rack Mount ,Shall have all accessories including coupler plates pre loaded with 12 Nos of LC couplers (OM3) with all accessories complete in all respect. Pigtails Should Complie to ITU-G657.B-Bend insestive fiber. Make-Siemon/Panduit/Legrand .

Supplying & Fixing of Fiber Optic LC style fully loaded Patch Panel (FOPP), 19" Rack Mount ,Shall have all accessories including coupler plates pre loaded with 24 Nos of LC couplers (OM3) with all accessories complete in all respect. Pigtails Should Complie to ITU-G657.B-Bend insestive fiber.. Make-Siemon/Panduit/Legrand

Supplying & Fixing of Fiber Optic Patch Cable (LC-LC), 3 Mtrs. Long, ISO/IEC-11801-OM3 50μ Duplex, LSZH,All patch cords shall conform to EIA/TIA-568C.3 and ISO/IEC-11801,Shall be Duplex Multi Mode Fiber Optic Patch Cords OM3 50μ,Shall support network line speeds up to 10 Gbps.Shall have LC-LC Connector connectors at the ends complete in all respect.. Make-Siemon/Panduit/Legrand

Supply & Fixing of OM3 50/125μ Type Pigtails of ISO/IEC-11801-OM3 Pigtails with LC Type Connectors,pigtails for terminating fibers on the FOPP complete in all respect. Make-Siemon/Panduit/Legrand .

Supplying, Installation, Testing & Commissioning of 50μ, 6-core Multi mode OM3 metallic armored Fiber cable as per ISO/IEC-11801, Shall be able to meet Gigabit & 10 Gigabit Ethernet performance up to 300 meters requirement specified by IEEE 802.3z (1000 Base-X) & IEEE 802.3ae (10G Base-X) Tensile load should be 4000 Newton or higher and crush resistance should be 4000 Newton or higher ,The attenuation @ 850 nm should be ≤ 2.7 (Max) db/Km and @ 1300 nm should be ≤ 0.7 (Max) dB/Km, the fiber construction can be unitube or multitube, but tensile and crush resistance parameters should be matched, the jacket shall be FRLSZH complete in all respect. . Make-Siemon/Panduit/Legrand

Supplying, of 100 Pair anealed tinned copper conductor PVC insulated and sheathed armoured copper telephone cables with suitable clamps, saddles and including making terminal joints complete as required.Make-Finolex/Delton/Vimco

Supplying, of 50 Pair anealed tinned copper conductor PVC insulated and sheathed armoured copper telephone cables with suitable clamps, saddles and including making terminal joints complete as required.Make-Finolex/Delton/Vimco

Supplying, Installation, Testing & Commissioning of of 50 Port telephone Jack Panel Approved.. Make-Siemon/Panduit/ Legrand.

Supplying Installation testing and Commissioning of 12 port 10/100/1000BASE-T POE ports and four GbE/10GbE SFP/SFP+ uplink ports, layer 3 from day1 having static & RIP ,stackable upto 10 switches, should support external redundant power supply, certified , each switch should be provided with stacking port/cable complete in all respect Approved Make-Juniper/Cisco/Extreme

Supplying Installation testing and Commissioning of 24 port 10/100/1000BASE-T POE ports and four GbE/10GbE SFP/SFP+ uplink ports, layer 3 from day1 having static & RIP ,stackable upto 10 switches, should support external redundant power supply, certified , each switch should be provided with stacking port/cable complete in all respect Approved Make-Juniper/Cisco/Extreme

Supplying, Installation, Testing & Commissioning of 48 port 10/100/1000BASE-T ports and four GbE/10GbE SFP/SFP+ uplink ports layer 3 from day1 having static & RIP , stackable upto 10 switches, should support external redundant power supply, certified EAL3 , each switch should be provided with stacking port/cable. Make-Juniper/Cisco/Extreme

Supplying Installation testing and Commissioning of SFP+ 10 Gigabit Ethernet Direct Attach Copper (twinax copper cable) 1m in length complete in all respect. Approved Make-Juniper/Cisco/Extreme

Supplying Installation testing and Commissioning of Small Form Factor Pluggable 1 Gigabit Ethernet (SFP+) SR Optics Approved Make-Juniper/Cisco/Extreme

Supplying Installation testing and Commissioning of 32 Port Fiber Switch 10/100/1000BASE-T ports, with up to 4X 10GbE uplinks and 2X 40GbE uplinks, Switch should support stacking bandwidth of minimum 160gbps, Modular operating system, 32 1 Gig SFP port with additional 4 no. of 10g SFP+PORT, redundant power supply, layer3 switch, each switch should be provided with stacking port/cable complete in all respect. Approved Make-Juniper/Cisco/Extreme

Supplying Installation testing and Commissioning of SFP 1000Base-T 10/100/1000 Copper Transceiver Module for up to 100m transmission on Cat6 complete in all respect. Approved Make-Juniper/Cisco/Extreme.

Supplying & Fixing of Floor Standing Network/Server Rack - 42U / 800w / 800d, with Heavy Duty Extruded Aluminium Frame for rigidity. Top cover with FHU provision. Top & Bottom cover with cable entry gland plates. Two pairs of 19” mounting angles with ‘U’ marking. Depth support channels - 3 pairs. With a Overall Weight Carrying Capicity of 500Kgs. Side Panels - 42U/800d Front MS Door Perforated honeycomb 42U/800w Rear MS Door Split Perforated honeycomb 42U/800wFan 90CFM 230V AC, 4” dia Castors with Brake (set of 4) Vertical Cable manager 80mmW 42U Shelf, Stationery 700mm N/W PDU 12Sockets 5/15Amps with MCB Mounting Hardware (Pkt. Of 20) earthing Kit 150mmH Cable manager 1U MS with Loops complete in all respect. Make-APC/APW/HEINRICH

Supplying & Fixing of Floor Standing Network Rack - 22U / 600w / 800d, with Heavy Duty Extruded Aluminium Frame for rigidity. Top cover with FHU provision. Top & Bottom cover with cable entry gland plates. Two pairs of 19” mounting angles with ‘U’ marking. Depth support channels - 3 pairs. With a Overall Weight Carrying Capicity of 500Kgs. Side Panels - 22U/800d Front MS Door perforated honeycomb 22U/600w Rear MS Door (Fully Perforated - Mesh) 22U/600w Fan 90CFM 230V AC, 4” dia Castors with Brake (set of 4) Cable manager 1U MS with Loops Shelf, Stationery 475mm N/W PDU 7Sockets 5Amps with MCB Mounting Hardware (Pkt. Of 20) Vertical Cable Channel 50mmW 22U complete in all respect.Make-APC/APW/HEINRICH

Supplying & Fixing of Network Rack 6U Rack complete in all respect.

Supplying and drawing following pair 0.5 sq mm FR PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 1.18.2: 2 Pair

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 1.21.2: 25 mm

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 1.27.1: 1 or 2 Module (75mmX75mm)

Supplying, fixing, connecting & testing of Telephone Tag Block krone type in a suitable size 1.6 mm thick dust and vermin proof Sheet steel enclosure duly painted by synthetic enamel over anti corrosive primer, lockable and hinged cover with provision for cable through glands complete in all respects. NS-1.1: 5 pair Krone

Supplying, laying, testing and commissioning of following size anealed tinned copper conductor PVC insulated and sheathed armoured copper telephone cables with suitable clamps, saddles and including making terminal joints complete as required. NS-2.1: 5 pair

NS-2.2: 20 pair

EQUIPMENT: Supplying & Fixing of Non- PCB based Information Outlet (I/O) RJ45, Tolless Termination TIA-568C Category-6, Termination of Catergory-6 UTP Cable, UL listed ,Shall conform to Category-6 as per the EIA/TIA-568C.2,Shall support network line speeds up to 1 Gbps, Shall have RJ-45 type connector with bend limiting and strain relief boot for securing IDC contacts from external forces and for maintaining the bend radius of the cable, Shall have minimum duraility of 950 or Above mating cycles and 200 termination cycles. Certified by independent labs like ETL/GHMT/3P for compliance to EIA/TIA-568C.2 complete in all respect..

Supplying & Fixing of Single Faceplate Shall be Single Port (RJ45) square plate, dimension as per commercially available modular office furniture.Shall have spring shuttered front access for preventing ingress of dust,Shall be supplied with Gang Box of the same size by System Integrator complete in all respect.

Supplying & Fixing of UTP Jack Panel, loaded with 24 nos UTP ports for Non-PCB based IO Jacks (RJ45, TIA-568C Category-6, Shall have integrated bonding bar or other mechanism for grounding, Shall be loaded with individually replaceable 24 nos. Category-6 certification by Jacks complying with TIA-568.C.2 , Shall be having a 6 port module construction for better cable dressing at the rear, the jacks shall have RJ-45 type connector with bend limiting and strain relief boot for securing IDC contacts from external forces and for maintaining the bend radius of the cable complete in all respect. . Make-Siemon/Panduit/Legrand

Supplying & Fixing of Rack -Wall Mount - 15U - 600W - 500D - Double Fan Provision - Black Fine Tex, Metal Cable Manager - 01U - Plastic Cable Loop's Mountable - Pastal Fine Tex. - Assembly, Power Distribution Unit - 06/13 Amp Multi-Standard - 06 Socket - Single Pole / Screw Mountable / 06 Amp MCB / Alternating Current - 06 Amp 3 Pin Plug with Power Cable 0.75 sq.mm 3 meter Length - Black Fine Tex. - Assembly complete in all respect.

Supplying, of 50 Pair armoured Jelly filled copper conductor armoured Cable with suitable clamps, saddles and including making terminal joints complete as required.

Supplying Installation testing and Commissioning of Small Form Factor Pluggable 1 Gigabit Ethernet (SFP+) SR Optics

Supply Installation Testing and Commissioning of Digital Phone 6 key display Backlit keypad Hands-free working Easy to use soft keys / LCD prompts on display model Directory dial key 1000 system, 1000 group, 10 personal, 600 phone book Conference key Wall mountable Message waiting indicator .

Supply Installation, Testing and Commissioning of Analog CLI Phone with handsfree.

Close Circuit Television and Security System: (A) CCTV (Video Surveillance): Supplying, installation, testing and commissioning of 2 megapixels resolution Network Dome Camera for true HD quality images, 2.8 – 12 mm varifocal lens,True Day/Night (TDN) functionality for true color image ,Motion Detection 4 Zones, Multi- Level Sensitivity Privacy Zones 4 Zones,Snapshoot Support JPEG format Password Protection Support Character Display Support(Channel /Date) ONVIF Yes,IR Illumination20-30M IR illuminators for clear images in low light conditions Wide Dynamic Range 3D noise reduction for sharper images and lower bandwidth use in low light ONVIF compliant complete in all respect.Make-Tyco/Mobotix/Pelco

Supply, installation, testing and commissioning of 2 megapixels resolution Network Bullet camera camera,Imager 1/2.8”SONY 2.43 mega low illumination CMOS,Video Compression. .H.264/MJPEG,Day/Night .Mechanical ICR,Minimum Illumination-0Lux/F1.4(IR ON) IR Illumination-40-50M,,Electronic Shutter-Auto/Manual(1/25~1/10000) Lens 2.8 – 12 mm varifocal lens,Resolution Main-stream:D1/Q1080P(960*540)/HD720P/ HD1080P 1-25/30fps,Digital Noise Reduction-3D,Wide Dynamic Range-Digital WDR Motion Detection -4 Zones, Multi- Level Sensitivity,Privacy Zones-4 Zones,Snapshoot-Support JPEG format,Password Protection-Support,Character Display-Support(Channel /Date).Regulatory Emissions-FCC Part 15 CE: EN55022,Immunity -CE: EN50130-4,IP Rating- IP66 rated enclosure to protect against dust and water damage ONVIF compliant .Make-Tyco/Mobotix/Pelco

Supplying of 4U Rack mount single chassis Network Video Recorder with dual Gb NIC, 1 DVI-I + HDMI + 1 Display Port, max 2 simultaneous monitors, RS-232/485 serial port, DVD, Server Operating System- Windows 10,Ubuntu Linux 16.04, Gen 4 Intel Core i7, Local Client Display Rate (FPS)Windows – 700 FPS (HD)Linux – 900 FPS (HD),High Performance, High Reliability IP Recorder. — Continuously records 400Mbps (Windows) & 800 Mbps (Linux)of video while hosting a local client, multiple remote clients and the web server on a single server,RAM-8 GB, 16 GB (Optional)solid-state operating system drive,USB-6 x USB 2.0, 2 x USB 3.0 high air flow cooling and hardware monitoring features ensure maximum uptime. keyboard and mouse, Professional Grade client and server software pre-installed and software updates. Access live and recorded video on multiple client PCs with free Windows, Mac or Linux client application. web server application is pre-installed on the server to access video through a web browser or free Mobile iPhone / iPad and Android apps. Maximum Storage Capacity 240TB RAID6 & Maximum Hard Drive 20 Slot(Up to 12TB) Support Up to 128 IP Camera. Make: Tyco/Mobotix/Pelco

Supply, installation, testing and commissioning of Enterprise Class 6TB HDD. Make-WD/Seagate

Supply, installation, testing and commissioning of Video Management System (VMS) software shall be used to view live and recorded video from capture cards and IP devices connected to local and wide area networks. The VMS software shall have a client/server-based architecture that can be configured as a standalone VMS system with the client software running on the server hardware and/or the client running on any network-connected TCP/IP workstation. Multiple client workstations shall be capable of simultaneously viewing live and/or recorded video from one or more servers. Multiple servers shall also be able to simultaneously provide live and/or recorded video to one or more workstations. The VMS server software shall also have the ability to be installed on an IP edge device—such as an IP camera or encoder that allows for 3rd party applications—allowing the device to serve as both a server and IP video recording device.The VMS shall not charge for the number of concurrent clients (min. 50 thick clients and 16 mobile clients to be provided along with VMS).Make-Tyco/Mobotix/Pelco

Supply, installation, testing & commissioning of 12 Port PoE+ Switch with 2 SFP slots 12 x 10/100/1000 Base-T PoE+ ports and additional 2 100/1000X SFP PORTS Should support PoE+ as per IEEE 802.3 at with PoE budget of 100W.Should support STP, RSTP, MSTP, IGMP v1/v2/v3 snooping, STP root guard, Voice VLAN, MLD snooping (MLDv1 and v2), IEEE 802.3ac VLAN tagging IEEE 802.17/equivalent for sub 50ms ring protection in following scenario : single, dual fibre cuts in ring and when fibre cut at common shared link in between two or more rings. Approved Make-Juniper/Cisco/Extreme

Supply , Installation , Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i5 7th Gen Processor (12M Cache, 6 core, 3.2 GHz); RAM: 16GB RAM ; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; 4GB 4K Graphics Card; Network interface card: Integrated Intel(R) Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 2 TB, 7200 RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 10 Professional 64 Bit or latest complete etc. as required. Make: HP/DELL/

Supplying, Installation,Testing & Commissioning of 55 " LED Full HD TV Resolution 1920 x 1080 ,Contrast Ratio (Typical) 5000:1,Built-in Speaker (10W + 10W), Magic Clone (to USB), Auto Source Switching & Recovery, Lamp Error Detection, Super Clear Coating, Temperature Sensor, Plug and Play (DDC2B), Pivot Display, Clock Battery, PIP/PBP, Video Wall (10x10), Image Rotation, Button Lock, HDCP Support, Smart Scheduling, Smart F/W update, Built-In MagicInfo Premium-Swith Mounting Brackets as per Technical Specification complete in all respect. Approved Make-Sony/Samsung/Planar

Supply, installation, testing and commissioning of Network Video Recorder , Live view/Resolution 5MP/3MP/1080p/720p,Motion Detection Control Privacy Mask Control. USB interface-1 × USB 2.0 and 1 × USB 3.0,Security-HTTPS, SSL, Watermark, User Authentication, Miscellaneous-N+1 hot spare. Alarm in/out -4 / 1,Network interface-1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface, Security-HTTPS, SSL,Video/Audio output-VAG,HDMI and Audio. Watermark, User Authentication,Incoming bandwidth-100Mbps,Outgoing bandwidth-80Mbps,HDMI output,VGA Output,Protocol-IPv4, IPv6, TCP/IP protocol, PPPoE, DHCP, DNS, DDNS, NTP, SADP, SMTP, SNMP, NFS, and iSCSI are supported.TCP, UDP and RTP for unicast, UPnPTM, ONVIF, PSIA,Support 32 IP Camera, 2 SATA interfaces for 4 HDDs Upto 4TB for each disk. Make-Tyco/Mobotix/Pelco

Supply, installation, testing and commissioning of 4 TB HDD. Make: WD/Seagate

LT PANELS & DISTRIBUTION BOARDS: B) FRONT OPERATED PANEL: Design, manufacture, supplying fixing in position of the following front operated cubicle type,compartmentalised with front access, dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42 protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs, bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable for a fault level of 25 KA symmetrical at 415 volts. i) All switchboards shall be modular type and have provision for entry of cables from the top /bottom as required. ii) The cost shall include providing and fixing of 100 x 50 x 6 mm channels for switchboard support. iii) All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The Busbars insulation shall be with heat shrinkable sleeves. SMC/DMC shrouds and busbar supports shall be used. iv) All MCCB shall have phase barriers, rotary handles and extension terminal as required . v) All unbalanced kWH meter shall have communication module for BMS connectivity RM MDB-1 ( Ground Floor ) (Typical for MDB-2 ( 1st Floor) to MDB-5 ( 5th Floor ) A) INCOMER: 1 No.100 amps 4P MCCB (25 KA) with thermal Magnetic release (PRTM) with Class-C transient voltage surge suppression device suitable for 3 phases as per specifications. B) METERING & INDICATION : i) 1 set of R,Y,B phase indicating lamps, ii) 1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB, iii) 1 No. (0-200A) Ammeter with ASS with 3 nos.100/5A CT's, iv) 1 No. Digital Electronic KWH meter(Dual Source). C) BUS-BAR: i) 1 Set of 150A TPN Aluminium Bus Bar with colour coded PVC Sleeves D) OUTGOINGS: i) 7 Nos. 63A FP MCB (10 KA), ii) 3 No. 40A FP MCB (10 KA) RM MDB-1 ( Ground Floor ) (Typical for MDB-2 ( 1st Floor to 5th Floor ) as described above

RM UMDB-1 ( Ground Floor ) (Typical for UMDB-2 ( 1st Floor) to UMDB-5 ( 5th Floor ) A) INCOMER: 1 No.100 amps 4P MCCB (25 KA) with thermal Magnetic release (PRTM) with Class-C transient voltage surge suppression device suitable for 3 phases as per specifications. B) METERING & INDICATION: i) 1 set of R,Y,B phase indicating lamps, ii) 1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB, iii) 1 No. (0-200A) Ammeter with ASS with 3 nos.100/5A CT's, iv) 1 No. Digital Electronic KWH meter(Dual Source)., C) BUS-BAR : i) 1 Set of 150A TPN Aluminium Bus Bar with colour coded PVC Sleeves D) OUTGOINGS: i) 7 Nos. 63A FP MCB (10 KA) ii) 3 No. 40A FP MCB (10 KA) RM UMDB-1 ( Ground Floor ) (Typical for UMDB-2 ( 1st Floor) to UMDB-6 ( 5th Floor ) as described above

LIFT PANEL-1(TYPICAL FOR LIFT PANEL-2,3,4) A) INCOMER: The ATS shall be complying to Standard IEC 60947-6-1 for transfer and 60947-3 for disconnection function.It shall have three distinct stable positions .The ATS shall have all the four poles fully rated and integrated controller. The ATS shall be rated at 100A , 4P : Model - Atys g or equivalent

1 No.100 amps 4P MCCB (25 KA) with thermal Magnetic release (PRTM) with Class-C transient voltage surge suppression device suitable for 3 phases as per specifications. B) METERING & INDICATION: i) 1 set of R,Y,B phase indicating lamps, ii) 1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB, iii) 1 No. (0-200A) Ammeter with ASS with 3 nos.100/5A CT's, iv) 1 No. Digital Electronic KWH meter(Dual Source)., C) BUS-BAR: i) 1 Set of 150A TPN Aluminium Bus Bar with colour coded PVC Sleeves D) OUTGOINGS: i) 3 Nos. 63A FP MCB (10 KA), ii) 2 No. 40A DP MCB (10 KA), iii) 3 No. 63A MPCP MCB (10 KA) LIFT PANEL-1(TYPICAL FOR LIFT PANEL-2,3) as described above

MDB BUNGALOW: Supplying, Fabricated, Installation, Testing & commissioning of Metal clad LT cubical wall/Floor mounted self supported totally enclosed compartmentalized separate compartment for each Meter with 1 No. SPN MCB earth bus & studs as required having padlock and sealing arrangement for each compartment, dust and vermin proof IP-42 protection made of 1.6 mm thick CRCA sheet steel duly powder coated for indoor application having arrangement for incoming/outgoing cable termination, earthing, insulated aluminium Bus Bar 3 phase 4 wire of suitable size in a separate chamber, suitable for 415V 3 phase 50 Hz AC supply duly prewired with 10 sq.mm Copper wire, from in-comer MCCB to bus bar and upto connectors mounted in an integrated loose wire box suitable for following mountings and switchgear accessories. (suitable provision for 15 Nos. Three phase energy meter). A) INCOMER: 1 No. 100 amps 4P MCCB(16 KA) with thermal Magnetic release (PRTM) with Class-C transient voltage surge suppression device suitable for 3 phases as per specifications. B) METERING & INDICATION for each Incomer: i) 1 set of R,Y,B phase indicating lamps, ii) 1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB, iii) 1 No. (0-315A) Ammeter with ASS with 3 nos. 250/5A CT's, iv) 1 No. Digital Electronic KWH meter(Dual Source)., C) BUS-BAR: i) 1 Set of 300A TPN Aluminium Bus Bar with colour coded PVC Sleeves D) OUTGOINGS : i) 4 Nos. 63A 4P MCB(10 KA) MDB-3 ( MDB BUNGALOW) as described above

MDB-4(GRADE-3 HOUSE): Supplying, Fabricated, Installation, Testing & commissioning of Metal clad LT cubical wall/Floor mounted self supported totally enclosed compartmentalized separate compartment for each Meter with 1 No. SPN MCB earth bus & studs as required having padlock and sealing arrangement for each compartment, dust and vermin proof IP-42 protection made of 1.6 mm thick CRCA sheet steel duly powder coated for indoor application having arrangement for incoming/outgoing cable termination, earthing, insulated aluminium Bus Bar 3 phase 4 wire of suitable size in a separate chamber, suitable for 415V 3 phase 50 Hz AC supply duly prewired with 10 sq.mm Copper wire, from in-comer MCCB to bus bar and upto connectors mounted in an integrated loose wire box suitable for following mountings and switchgear accessories. (suitable provision for 15 Nos. Three phase energy meter). A) INCOMER: 1 No. 250 amps 4P MCCB(16 KA) with thermal Magnetic release (PRTM) with Class-C transient voltage surge suppression device suitable for 3 phases as per specifications. B: METERING & INDICATION for each Incomer: i) 1 set of R,Y,B phase indicating lamps, ii) 1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB, iii) 1 No. (0-315A) Ammeter with ASS with 3 nos. 250/5A CT's, iv) 1 No. Digital Electronic KWH meter(Dual Source). C) BUS-BAR : i) 1 Set of 300A TPN Aluminium Bus Bar with colour coded PVC Sleeves D) OUTGOINGS: i) 20 Nos. 40A TPN MCB (10 KA) MDB-4(GRADE-3 HOUSE) as described above.

MDB-5(GRADE-4 HOUSE) (TYPICAL FOR MDB-5.1 (GRADE-4 HOUSE)): Supplying, Fabricated, Installation, Testing & commissioning of Metal clad LT cubical wall/Floor mounted self supported totally enclosed compartmentalized separate compartment for each Meter with 1 No. SPN MCB earth bus & studs as required having padlock and sealing arrangement for each compartment, dust and vermin proof IP-42 protection made of 1.6 mm thick CRCA sheet steel duly powder coated for indoor application having arrangement for incoming/outgoing cable termination, earthing, insulated aluminium Bus Bar 3 phase 4 wire of suitable size in a separate chamber, suitable for 415V 3 phase 50 Hz AC supply duly prewired with 10 sq.mm Copper wire, from in-comer MCCB to bus bar and upto connectors mounted in an integrated loose wire box suitable for following mountings and switchgear accessories. (suitable provision for 15 Nos. Three phase energy meter). INCOMER: 1 No. 160 amps 4P MCCB(16 KA) with thermal Magnetic release (PRTM) with Class-C transient voltage surge suppression device suitable for 3 phases as per specifications. METERING & INDICATION for each Incomer, 1 set of R,Y,B phase indicating lamps, 1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB, 1 No. (0-315A) Ammeter with ASS with 3 nos. 250/5A CT's, 1 No. Digital Electronic KWH meter(Dual Source). BUS-BAR: 1 Set of 200A TPN Aluminium Bus Bar with colour coded PVC Sleeves OUTGOINGS: 20 Nos. 40A TPN MCB (10 KA) MDB-5(GRADE-4 HOUSE) (TYPICAL FOR MDB-5.1 (GRADE-4 HOUSE)) as described above

MDB-3( GUEST HOUSE): Supplying, Fabricated, Installation, Testing & commissioning of Metal clad LT cubical wall/Floor mounted self supported totally enclosed compartmentalized separate compartment for each Meter with 1 No. SPN MCB earth bus & studs as required having padlock and sealing arrangement for each compartment, dust and vermin proof IP-42 protection made of 1.6 mm thick CRCA sheet steel duly powder coated for indoor application having arrangement for incoming/outgoing cable termination, earthing, insulated aluminium Bus Bar 3 phase 4 wire of suitable size in a separate chamber, suitable for 415V 3 phase 50 Hz AC supply duly prewired with 10 sq.mm Copper wire, from in-comer MCCB to bus bar and upto connectors mounted in an integrated loose wire box suitable for following mountings and switchgear accessories. (suitable provision for 15 Nos. Three phase energy meter). A) INCOMER: 1 No. 125 amps 4P MCCB(16 KA) with thermal Magnetic release (PRTM) with Class-C transient voltage surge suppression device suitable for 3 phases as per specifications. B) METERING & INDICATION for each Incomer, i) 1 set of R,Y,B phase indicating lamps, iii) 1 No. (0-315A) Ammeter with ASS with 3 nos. 250/5A CT's, iv) 1 No. Digital Electronic KWH meter(Dual Source). C) BUS-BAR: i) 1 Set of 300A TPN Aluminium Bus Bar with colour coded PVC Sleeves D) OUTGOINGS: i) 9 Nos. 63A 4P MCCB(16 KA) with thermal Magnetic release MDB-3( GUEST HOUSE) as described above

DMB-2(OFFICER QTR.): Supplying, Fabricated, Installation, Testing & commissioning of Metal clad LT cubical wall/Floor mounted self supported totally enclosed compartmentalized separate compartment for each Meter with 1 No. SPN MCB earth bus & studs as required having padlock and sealing arrangement for each compartment, dust and vermin proof IP-42 protection made of 1.6 mm thick CRCA sheet steel duly powder coated for indoor application having arrangement for incoming/outgoing cable termination, earthing, insulated aluminium Bus Bar 3 phase 4 wire of suitable size in a separate chamber, suitable for 415V 3 phase 50 Hz AC supply duly prewired with 10 sq.mm Copper wire, from in-comer MCCB to bus bar and upto connectors mounted in an integrated loose wire box suitable for following mountings and switchgear accessories. (suitable provision for 15 Nos. Three phase energy meter). A) INCOMER: 1 No. 250 amps 4P MCCB(16 KA) with thermal Magnetic release (PRTM) with Class-C transient voltage surge suppression device suitable for 3 phases as per specifications. B) METERING & INDICATION for each Incomer: i) 1 set of R,Y,B phase indicating lamps, ii) 1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB, iii) 1 No. (0-315A) Ammeter with ASS with 3 nos. 250/5A CT's, iv) 1 No. Digital Electronic KWH meter(Dual Source). C) BUS-BAR: i) 1 Set of 300A TPN Aluminium Bus Bar with colour coded PVC Sleeves D) OUTGOINGS: i) 20 Nos. 40A TPN MCB (10 KA) DMB-2(OFFICER QTR.) as described above

ENERGY METER: Supplying, instalation, testing & commissioning of metering system with dual source ISI marked 415 Volts, 50Hz, 3- Phase 4- Wire, accuracy class 1, 10- 60 A continuas rating tariff energy meter with 100% neutral along with standard features as per as per ISI & with inbuilt features like direct reading KW, KWH, MD and as follow.

Rising Mains (In Sandwiched Construction) & its Equipments: Design, manufacture, supply, installation, testing & commissioning of 400 amps rating (25 KA for 1 Sec) 4 pole rising mains in sandwich construction of aluminium bus bar with tap-off connection points at every 1000 mm intervals, expansion joints, fire barriers including necessary support and louvers for ventilation, fabricated out of 1.6 mm thick galvanized sheet steel painted with approved paint shade including 2 Nos. of 25 x 6 mm Cu. earthing conductor through out the length of the rising mains (Phase sequence shall match the sequence of the incoming breaker provided at the LT Panel). Thrust pad shall be provided for each rising main for necessary support to rising main and to prevent the bus bar expansion in downward direction. Also provide end cover to close the end of rising main and to provide extra end supports to the bus bars. Rising Mains -1 described as above

Design, manufacture, supply, installation, testing & commissioning of 200 amps rating (25 KA for 1 Sec) 4 pole rising mains in sandwich construction of aluminium bus bar with tap-off connection points at every 1000 mm intervals, expansion joints, fire barriers including necessary support and louvers for ventilation, fabricated out of 1.6 mm thick galvanized sheet steel painted with approved paint shade including 2 Nos. of 25 x 6 mm Cu. earthing conductor through out the length of the rising mains (Phase sequence shall match the sequence of the incoming breaker provided at the LT Panel). Thrust pad shall be provided for each rising main for necessary support to rising main and to prevent the bus bar expansion in downward direction. Also provide end cover to close the end of rising main and to provide extra end supports to the bus bars. Rising Mains -1 described as above

Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of following End Feed Unit /MCCB Boxes fabricated out of 2mm thick CRCA sheet steel duly powder coated in cubical formation, dust and vermin proof, coupled with rising mains. Boxes shall be fabricated as per specifications. 2 Nos. of 25 x 3 mm copper earthing terminals shall be provided. 400 amps TPN MCCB (35 KA)

200 amps TPN MCCB (35 KA)

Supply of following capacity TPN tap off box made of 1.6mm thick sheet steel enclosure duly painted with powder coating on existing rising mains with provision of fixing MCCB/HRC fuse . (Legrand/ C&S or equivalent as approved by the Deptt.) 125A Tap-off Box with inbuilt Disconnection (Legrand/ C&S or equivalent as approved by the Deptt.) on Cover ( W/0 MCCB/HRC fuse)

Audio-Visual System in Conference Room: Audio-Visual System in Conference Room (13 Seater- 3 Nos.): Supply Installation Testing & Commissioning of Diagonal Size 75", Resolution: Ultra HD (3840 x 2160),Active Display Area(mm): 1650mm H x 928mm V, Brightness(Typ.): Minimum 410 nit, Contrast Ratio: Typical 1200:1, Bezel Width Maximum 12.5mm etc complete required as per specifications. Make: Mitshubishi/Planner/Solaris.

SITC of Wired Table Top Digital Delegate unit with Gooseneck Microphone with Super Cardiod / Array technology pattern, If gooseneck length : 14" to 16". Gooseneck Microphone : Not detachable. Connection : standard CAT5/CAT6/LAN cable. Twin/dual Loudspeaker THD : 0,03 % at 50 mW/16ohm or better. Digital Signal processor limiter inbuilt, built in DSP limiter, 3.5mm headphone jack with volume control, Push to Talk button. Makes : Sennheiser / Brahler / Clock Audio

SITC of Wired Table Top Digital Chairman unit with Gooseneck Microphone with Super Cardiod / Array technology pattern, If gooseneck length : 14" to 16". Gooseneck Microphone : Not detachable. Connection : standard CAT5/CAT6/LAN cable. Twin/dual Loudspeaker THD : 0,03 % at 50 mW/16ohm or better. Digital Signal processor limiter inbuilt, built in DSP limiter, 3.5mm headphone jack with volume control, Priority and Next-Key for delegate control. Makes : Sennheiser / Brahler / Clock Audio

SITC of Digital Central Unit to controls minimum 350 discussion units. USB Conference recording. Electronically balanced XLR In & Out. Per Microphone recording option required to record minute of meeting. Open Media Control Protocol over Ethernet, Permanent malfunction monitoring and error diagnostics. Integrated PC with pre-installed control SoftwareIntegrated software package. Controller can connect a Screen, Mouse and Keyboard. Makes : Sennheiser / Brahler / Clock Audio

SITC of System cable CAT5/Multicore Cable with RJ45/6Pole Connector 2m etc complete as required. Makes : Sennheiser / Brahler / Clock Audio

SITC of System cable CAT5/Multicore Cable with RJ45/6Pole Connector 20m,etc complete as required. Makes : Sennheiser / Brahler / Clock Audio

Supply, Installation, testing and commissioning of wireless digital Handheld Microphone with 18 or more channel, RF output 80mW or more, super cardiod pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45 (specifications includes single microphone set of transmitter and receiver), battery backup 15 hours or more , Secure 256 bit AES encryption, rechargable battery, etc and complete as required..Makes : Sennheiser / NEUMAN / REVOLAB

Supply, Installation, testing and commissioning of wireless digital Headset Microphone with 18 or more channel, RF output 80mW or more, Omni-directional pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, 256-bit AES Encryption (specifications includes single microphone set of transmitter and receiver) , battery backup 15 hours or more , rechargable battery,etc and complete as required.. Makes : Sennheiser / Shure / REVOLAB

Supply, Installation, testing and commissioning of 4" two-way thin edge ceiling loudspeaker having 100V transformer power taps from 24watts to 6watts or better it should have metal back can for premium performance in demanding applications, Conical dispersion : 152° or more, Low impedance RMS continuous power of 30watts, impedance : 8 or less,frequency range : 70 Hz - 20 kHz, frequency response : 110 Hz- 20KHz , Max SPL should be 100dB or more etc complete required as per specifications..Makes : Auadc / AIM-Line / Mayer Sound

Supply, Installation, testing and commissioning of quad channel stereo Amplifier, 4 x 250 W watt @ 4 ohm stereo or more,@ 8 Ω Stereo 4 x 130 W or more , THD+N (@ 1 kHz) : < 0.1% (1/2 Rated Power) : Class-D, Convection cooled, Switching mode power supply, should have Protection features like : DC Short circuit & Over heating & Over load & Signal limiting , Fuse should be IEC C14 type Energy-star certified, Impedance 12 kΩ balanced, Sensitivity (1W/1m) 0 dB (1V RMS) , Frequency Response 20 Hz - 20 kHz or better , Signal / Noise > 90 dB or better , Crosstalk (@ 1 kHz) > 70 dB or better , LED indication for any fault detected for all the channels etc complete required as per specifications.Makes : Audac / Powersoft / d&B audio

SITC of Supply Installation Testing and Commissioning of digital signal processor with builtin Dante, minimum 10no. Or more Mic / line input with phantom power and AEC and 6 or more line output, at least 2 channel of USB input and output for software Video Conferencing,, Should have sampline rate of 48kHz or better, Should be expandable for port expansion, if required. or more,should support Control with App via iOS and Android devices, or any third-party control system, Shall have Built-in filters, feedback suppression, AGC etc complete as required as per specifications.Makes : Sennheiser / Symmatrix / Xylica.

Supply, Installation,Testing & Commissioning of Integrated Controller One RS-232/422/485 COM port with hardware and software handshaking Two RS-232 COM ports with software handshaking only 8 IR/serial, 8 relay, and 8 Versiport I/O ports Native BACnet®/IP support,Backwards compatible to run existing SIMPL programs Full Unicode (multi-language) support Increased network throughput and security,Secure access though Active Directory integration or standalone account management Hardware level security using 802.1x authentication,JITC certified model available for use in secure network environments,IIS v.6.0 Web Server,IPv6 ready,Front panel USB computer console port,1-space rack-mountable SDRAM: 512 MB,Flash: 4 GB,Memory Card: supports SD™ and SDHC™ cards up to 32 GB,External Storage: support USB mass storage devices up to 1 TB. Make-AMX/Extron/Crestron

Supply, Installation,Testing & Commissioning of iPad,Apple iOS 8; 9.7-Inch Retina Display; 2048x1536 Resolution A8X Chip with 64-bit Architecture; M8 Motion Coprocessor Wi-Fi (802.11a/b/g/n/ac); 32 GB Capacity 8 MP iSight Camera; FaceTime HD Camera Up to 10 Hours of Battery Life

An integrationSoftware to integrate the Controller with an Apple Ipad An Application to enable any Apple mobile devices to transform into a fully functional touch panel to seamlessly communicate with the Control processor Voice Control - Using Speech-to-Text and Text-to-Speech functionality within application, allows you to talk to your control system and have it talk to you with additional features of: •Page Flips and Popups Sounds,Multitouch. Make-AMX/Extron/Crestron

SITC of Cable Manager with 1 no. multiregion AC Power socket, , Black anodised/brushed aluminium finish,Tilt up lid with pass through holes for 1 HDMI, with audio, 1x LAN complete with CE, UL certification complete etc. as required.Make-AMX/Extron/Crestron

Supply, Installation, Testing & Commissioning of 4x4 HDMI Matrix switcher .Make-AMX/Extron/Crestron

SITC of FHD Video Conference Systems having 1+5 Party connectivity on FHD Resolution from day 1(Inbuilt/External) i/c wireless remote control, 12x Optical zoom , 10x Digital Zoom Full HD PTZ Camera, having minimum 50 presets, Input for 3 More External cameras, Dual Microphone, 3 Video outputs, Inbuilt SD card/Pen Drive Recording feature, PC connectivity for presentation sharing, necessary hardware, software, license, programming complete etc as required at site. Make: Sony/Polycom/Lifesize

SITC of H.264 Recording & Streaming Media Processor with 1xHDMI input for presentation input, 1 HDMI/DVI input for video input. Output: 1x RJ45 for streaming, 1x HDMI/DVI for local viewing. Should be able to do Picture in picture or picture by picture. Have inbuilt storage of 30GB HDD/Memory card, USB port for external storage supporting 1TB or more, Should support streaming & recording resolution of 1080p or more. Have inbuilt scaling capability. Streaming Protocol Support: RTSP, RTP, RTMP. Compression H.264 or better etc as required at site.

SITC of Wireless presentation device which supports video resolution upto 1080p (Full HD), with 1xHDMI / DVI/ DP output, PoE enabled Ethernet port, 1xUSB port for data sharing , Supports Windows laptops and MAC, as well as iOS, Windows and Android mobile operating systems, display minimum 2 users screen simultaneously on a single display through hardware dongle/ software app. Supports DHCP, Audio out. Support 40 or more concurrent users. Support Full HD video of 1080p @ 30fps or more etc as required at site. Make-AMX/Extron/Crestron

Supply, Installation, testing and commissioning of required cable of HDMI, VGA, Audio, power, speaker, Microphone and conenctors as per site requirement etc complete required. Make-AMX/Extron/Crestron

Supplying & Fixing of Floor Standing Rack network Rack - 22U / 600w / 800d, with Heavy Duty Extruded Aluminium Frame for rigidity. Top cover with FHU provision. Top & Bottom cover with cable entry gland plates. Two pairs of 19” mounting angles with ‘U’ marking. Depth support channels - 3 pairs. With a Overall Weight Carrying Capicity of 500Kgs. Side Panels - 22U/800d Front MS Door perforated honeycomb 22U/600w Rear MS Door (Fully Perforated - Mesh) 22U/600w Fan 90CFM 230V AC, 4” dia Castors with Brake (set of 4) Cable manager 1U MS with Loops Shelf, Stationery 475mm N/W PDU 7Sockets 5Amps with MCB Mounting Hardware (Pkt. Of 20) Vertical Cable Channel 50mmW 22U, Make-APC/APW/Valrack

Audio-Visual System in Conference Room (27Seater): Supply Installation Testing & Commissioning of 100" 4K UHD LED Display on Front wall, complete with installation along with suitable swivel wall mount etc. as required. Make: Sharp/Sony/Planner/NEC.

SITC of 65" 4K professional display with 400 nits or more, 1000:1 or more contrast, Viewing Angle: 178 deg (H)/178 deg(V), 1 x HDMI, 1 x DVI/DP input, Controls: RS 232/Ethernet, etc complete with installation along with suitable swivel wall mount etc. as required. Make: Sharp/Sony/Planner/NEC.

SITC of Wired Table Top Digital Delegate unit with Gooseneck Microphone with Super Cardiod / Array technology pattern, If gooseneck length : 14" to 16". Gooseneck Microphone : Not detachable. Connection : standard CAT5/CAT6/LAN cable. Twin/dual Loudspeaker THD : 0,03 % at 50 mW/16ohm or better. Digital Signal processor limiter inbuilt, built in DSP limiter, 3.5mm headphone jack with volume control, Push to Talk button. Makes : Sennheiser / Brahler / Clock Audio

SITC of Wired Table Top Digital Chairman unit with Gooseneck Microphone with Super Cardiod / Array technology pattern, If gooseneck length : 14" to 16". Gooseneck Microphone : Not detachable. Connection : standard CAT5/CAT6/LAN cable. Twin/dual Loudspeaker THD : 0,03 % at 50 mW/16ohm or better. Digital Signal processor limiter inbuilt, built in DSP limiter, 3.5mm headphone jack with volume control, Priority and Next-Key for delegate control. Makes : Sennheiser / Brahler / Clock Audio

SITC of Digital Central Unit to controls minimum 350 discussion units. USB Conference recording. Electronically balanced XLR In & Out. Per Microphone recording option required to record minute of meeting. Open Media Control Protocol over Ethernet, Permanent malfunction monitoring and error diagnostics. Integrated PC with pre-installed control SoftwareIntegrated software package. Controller can connect a Screen, Mouse and Keyboard. Makes : Sennheiser / Brahler / Clock Audio

SITC of System cable CAT5/Multicore Cable with RJ45/6Pole Connector 2m etc complete as required. Makes : Sennheiser / Brahler / Clock Audio

SITC of System cable CAT5/Multicore Cable with RJ45/6Pole Connector 20m,etc complete as required. Makes : Sennheiser / Brahler / Clock Audio

Supply, Installation, testing and commissioning of wireless digital Handheld Microphone with 18 or more channel, RF output 80mW or more, super cardiod pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45 (specifications includes single microphone set of transmitter and receiver), battery backup 15 hours or more , Secure 256 bit AES encryption, rechargable battery, etc and complete as required..Makes : Sennheiser / NEUMAN / REVOLAB

Supply, Installation, testing and commissioning of wireless digital Headset Microphone with 18 or more channel, RF output 80mW or more, Omni-directional pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, 256-bit AES Encryption (specifications includes single microphone set of transmitter and receiver) , battery backup 15 hours or more , rechargable battery,etc and complete as required.. Makes : Sennheiser / Shure / REVOLAB

Supply, Installation, testing and commissioning of 4" two-way thin edge ceiling loudspeaker having 100V transformer power taps from 24watts to 6watts or better it should have metal back can for premium performance in demanding applications, Conical dispersion : 152° or more, Low impedance RMS continuous power of 30watts, impedance : 8 or less,frequency range : 70 Hz - 20 kHz, frequency response : 110 Hz- 20KHz , Max SPL should be 100dB or more etc complete required as per specifications..Makes : Auadc / AIM-Line / Mayer Sound

Supply, Installation, testing and commissioning of quad channel stereo Amplifier, 4 x 250 W watt @ 4 ohm stereo or more,@ 8 Ω Stereo 4 x 130 W or more , THD+N (@ 1 kHz) : < 0.1% (1/2 Rated Power) : Class-D, Convection cooled, Switching mode power supply, should have Protection features like : DC Short circuit & Over heating & Over load & Signal limiting , Fuse should be IEC C14 type Energy-star certified, Impedance 12 kΩ balanced, Sensitivity (1W/1m) 0 dB (1V RMS) , Frequency Response 20 Hz - 20 kHz or better , Signal / Noise > 90 dB or better , Crosstalk (@ 1 kHz) > 70 dB or better , LED indication for any fault detected for all the channels etc complete required as per specifications.Makes : Audac / Powersoft / d&B audio

Supply Installation Testing and Commissioning of digital signal processor with builtin Dante, minimum 10no. Or more Mic / line input with phantom power and AEC and 6 or more line output, at least 2 channel of USB input and output for software Video Conferencing,, Should have sampline rate of 48kHz or better, Should be expandable for port expansion, if required. or more,should support Control with App via iOS and Android devices, or any third-party control system, Shall have Built-in filters, feedback suppression, AGC etc complete as required as per specifications.Makes : Sennheiser / Symmatrix / Xylica.

Supply, Installation,Testing & Commissioning of Integrated Controller One RS-232/422/485 COM port with hardware and software handshaking Two RS-232 COM ports with software handshaking only 8 IR/serial, 8 relay, and 8 Versiport I/O ports Native BACnet®/IP support,Backwards compatible to run existing SIMPL programs Full Unicode (multi-language) support Increased network throughput and security,Secure access though Active Directory integration or standalone account management Hardware level security using 802.1x authentication,JITC certified model available for use in secure network environments,IIS v.6.0 Web Server,IPv6 ready,Front panel USB computer console port,1-space rack-mountable SDRAM: 512 MB,Flash: 4 GB,Memory Card: supports SD™ and SDHC™ cards up to 32 GB,External Storage: support USB mass storage devices up to 1 TB. Make-AMX/Extron/Crestron

Supply, Installation,Testing & Commissioning of iPad,Apple iOS 8; 9.7-Inch Retina Display; 2048x1536 Resolution A8X Chip with 64-bit Architecture; M8 Motion Coprocessor Wi-Fi (802.11a/b/g/n/ac); 32 GB Capacity 8 MP iSight Camera; FaceTime HD Camera Up to 10 Hours of Battery Life

An integrationSoftware to integrate the Controller with an Apple Ipad An Application to enable any Apple mobile devices to transform into a fully functional touch panel to seamlessly communicate with the Control processor Voice Control - Using Speech-to-Text and Text-to-Speech functionality within application, allows you to talk to your control system and have it talk to you with additional features of: •Page Flips and Popups Sounds,Multitouch. Make-AMX/Extron/Crestron

SITC of Cable Manager with 1 no. multiregion AC Power socket, , Black anodised/brushed aluminium finish,Tilt up lid with pass through holes for 1 HDMI, with audio, 1x LAN complete with CE, UL certification complete etc. as required.Make-AMX/Extron/Crestron

SITC of Modular Digital Matrix switcher with Redundant power supply, frame of 16 input 16 output or more full matrix on input to output, 12.5 Gbps or more Digital Backpane bandwidth, including cards for Input: 12 x Twisted Pair/HDbaseT or more , 4 x HDMI or more,cards for Output: 12 x Twisted pair/HDbaseT or more, 4x HDMI or more, 2 or more Analog audio output, Resolution support for 4K or more with capability of handling colour bit depth of more than 12bits. HDCP 2.2 compliant & EDID management Transmision of audio,video,controls, Ethernet or power upto minimum 100mtrs or more. Preferably Hotswappable cards. HDMI audio embedding & deem bedding as per specifications complete as required.Make-AMX/Extron/Crestron

SITC of HDMI & Control twisted pair Transmitter with Input: 1x HDMI, 1x RS232/485 IR(Controls) , Output: 1x Twisted pair/HD base T input on RJ45, supporting transmission of audio,video, controls and power upto minimum 70 mtrs or more. Upto 4K resolution support at various distance, remote powering feature, HDCP 2.2 compliant & EDID as per specifications complete etc. as required. Make-AMX/Extron/Crestron

SITC of HDMI & Control twisted pair Receiver with Input:1x Twisted pair/HDbaseT input on RJ45, Output:1x HDMI, 1x RS232/IR(Controls) , supporting reception of audio,video, controls and power upto minimum 70mtrs or more. Upto 4K resolution support at various distance ,remote powering feature,HDCP 2.2 compliant & EDID. as per specifications complete etc. as required. Make-AMX/Extron/Crestron

SITC of FHD Video Conference Systems having 1+5 Party connectivity on FHD Resolution from day 1(Inbuilt/External) i/c wireless remote control, 12x Optical zoom , 10x Digital Zoom Full HD PTZ Camera, having minimum 50 presets, Input for 3 More External cameras, Dual Microphone, 3 Video outputs, Inbuilt SD card/Pen Drive Recording feature, PC connectivity for presentation sharing, necessary hardware, software, license, programming complete etc as required at site. Make: Sony/Polycom/Lifesize

SITC of Full HD Ceiling mounted PTZ Camera , 1/2.8", 2MP CMOS/CCD or better 10 or more preset positions, 20x or more Optical Zoom, Resolution: 1080p or better, S/N ratio: 50 dB or better,Pan angle: +/- 160 deg or more. Horizontal Viewing angle: 65deg or more.,supports Poe, Output: 1x HDMI, LAN, RS 232, etc as required at site.

SITC of H.264 Recording & Streaming Media Processor with 1xHDMI input for presentation input, 1 HDMI/DVI input for video input. Output: 1x RJ45 for streaming, 1x HDMI/DVI for local viewing. Should be able to do Picture in picture or picture by picture. Have inbuilt storage of 30GB HDD/Memory card, USB port for external storage supporting 1TB or more, Should support streaming & recording resolution of 1080p or more. Have inbuilt scaling capability. Streaming Protocol Support: RTSP, RTP, RTMP. Compression H.264 or better etc as required at site.

SITC of Wireless presentation device which supports video resolution upto 1080p (Full HD), with 1xHDMI / DVI/ DP output, PoE enabled Ethernet port, 1xUSB port for data sharing , Supports Windows laptops and MAC, as well as iOS, Windows and Android mobile operating systems, display minimum 2 users screen simultaneously on a single display through hardware dongle/ software app. Supports DHCP, Audio out. Support 40 or more concurrent users. Support Full HD video of 1080p @ 30fps or more etc as required at site. Make-AMX/Extron/Crestron

Supply, Installation,Testing & Commissioning of Wall-mount integrated lighting and shade control,Six channels of dimming or switching,Six groups of shade and drape control, Supports Cresnet® Occupancy Sensors and Shades, Linkable for up to 54 lighting channels and 54 shade groups,Up to 16 user-settable scenes Large ON and OFF buttons,Flip-up front cover reveals setup controls and programming port Six bargraphs show lighting levels and shade positions Easy setup from front panel or iLux® Designer software Supports multipoint control using up to 16 keypads Optional IR remote Master air-gap relay.

Supply, Installation,Testing & Commissioning of DIN Rail High-Voltage Switch, 8 feeds, 8 channels.

SITC of 10" table top touch panel, supporting PoE adapter, Resolution: 1280x 800 or better, 350nits or better, 700:1 contrast or better, memory: 2 GB or more as per specifications etc.as required.

Supply, Installation, testing and commissioning of required cable of HDMI, VGA, Audio, power, speaker, Microphone and conenctors as per site requirement etc complete required. Make-AMX/Extron/Crestron

Supplying & Fixing of Floor Standing Rack network Rack - 22U / 600w / 800d, with Heavy Duty Extruded Aluminium Frame for rigidity. Top cover with FHU provision. Top & Bottom cover with cable entry gland plates. Two pairs of 19” mounting angles with ‘U’ marking. Depth support channels - 3 pairs. With a Overall Weight Carrying Capicity of 500Kgs. Side Panels - 22U/800d Front MS Door perforated honeycomb 22U/600w Rear MS Door (Fully Perforated - Mesh) 22U/600w Fan 90CFM 230V AC, 4” dia Castors with Brake (set of 4) Cable manager 1U MS with Loops Shelf, Stationery 475mm N/W PDU 7Sockets 5Amps with MCB Mounting Hardware (Pkt. Of 20) Vertical Cable Channel 50mmW 22U, Make-APC/APW/Valrack

FOH Speakers:- SITC of Flying 3 way, high effeciency 15inch weatherised speaker with IP55 rating, Compression driver with 1.75" voice coil, 6" high mid speaker and 15" Horn loaded Mid-bass driver. Rotatable 90° x 40° coverage horn (horizontal & vertical mounting), Self-resetting tweeter overload protection. Max Output Power 1500 W, RMS Power 750 W @ 8 Ω, Sensitivity (1W/1m) 105 dB, Sound Pressure (Max. W/1m) 134 dB, Frequency Response (± 3 dB) 130 Hz - 20 kHz, Range (-10 dB) 85 Hz - 20 kHz. Make: Sennheiser-Audac/ Martin/ Renkun Heinz

Delay Speakers for upper and lower Balcony:- SITC of Flying 3 way, high effeciency 15inch weatherised speaker with IP55 rating, Compression driver with 1.75" voice coil, 6" high mid speaker and 15" Horn loaded Mid-bass driver. Rotatable 90° x 40° coverage horn (horizontal & vertical mounting), Self-resetting tweeter overload protection. Max Output Power 1500 W, RMS Power 750 W @ 8 Ω, Sensitivity (1W/1m) 105 dB, Sound Pressure (Max. W/1m) 134 dB, Frequency Response (± 3 dB) 130 Hz - 20 kHz, Range (-10 dB) 85 Hz - 20 kHz.Make: Sennheiser-Audac/ Martin/ Renkun Heinz

Stage Monitors:- SITC of 2 way, high effeciency 15inch weatherised speaker with IP56 rating, Compression driver with 1,3" voice coil, Rotatable 90° x 75° coverage horn (horizontal & vertical mounting), Self-resetting tweeter overload protection. Max Output Power 600 W, RMS Power 300 W @ 8 Ω, Sensitivity (1W/1m) 100 dB, Sound Pressure (Max. W/1m) 125 dB, Frequency Response (± 3 dB) 60 Hz - 19 kHz, Range (-10 dB) 45 Hz - 20 kHz.Make: Sennheiser-Audac/ Martin/ Renkun Heinz

Sub Woofers:- SITC of High output 18" flying woofer (800 Watt), Weatherproof DuraCoat™ texture paintwork to make it IP55 rated, Max. Power 1600 W, RMS Power 800 W@ 8 Ω, Sensitivity (1W/1m) 102 dB, Sound Pressure (Max. W/1m) 131 dB, Ingress Protection rating IP55, Frequency Response (± 3 dB) 37 Hz - 130 Hz, Range (-10 dB) 33 Hz - 130 Hz.Make: Sennheiser-Audac/ Martin/ Renkun Heinz

Amplifiers:- SITC of 4 channal Class D Amplifier, RMS Power @ 4 Ω Stereo 4 x 750 W, @ 8 Ω Bridge 2 x 1500 W and @ 8 Ω Stereo 4 x 380 W, Signal / Noise > 95 dB, THD+N (@ 1 kHz) < 0.05% (1/2 Rated Power), Damping factor > 200, Operating temperature 0° ~ 40° @ 95% Humidity, Frequency Response (± 3 dB) 20 Hz - 20 kHz, Inputs Sensitivity (1W/1m) -19.5 dB ~ 27 dB, Impedance 10 kΩ balanced, Over heating, Over load, Signal limiting features avaliable. Make: Sennheiser-Audac/ Martin/ Renkun Heinz

Front Fills:- SITC of2 way 8" low frequency loudspeaker with 1" Dome tweeter, Vertical and horizontal mounting, 100V and low impedance connection possibility, Impedance 8 Ω, Max. Power 140 W, Sensitivity (1W/1m) 89 dB, RMS Power 70 W, Frequency Range (-10 dB) 50 Hz - 20 kHz, Response (± 3 dB) 60 Hz - 18 kHz, Dispersion angle H-110 Degree and V-110 Degree, Line Transformer Tapping 15W/30W/60W. Make: Sennheiser-Audac/ Martin/ Renkun Heinz

Amplifier for front Fills:- SITC of Quad channel class D amplifier, RMS Power 250W @ 4 Ω Stereo, 500W @ 8 Ω Bridge and 140W @ 8 Ω, Signal / Noise > 90 dB, THD+N (@ 1 kHz) < 0.1% (1/2 Rated Power), Crosstalk (@ 1 kHz) > 70 dB, Operating, temperature 0° ~ 40° @ 95% Humidity, Frequency Response (± 3 dB) 20 Hz - 20 kHz, Inputs Sensitivity (1W/1m) 0 dB (1V RMS). Make: Sennheiser-Audac/ Martin/ Renkun Heinz

Green & Control Room Speakers:- SITC of2 way 5 1/4" low frequency loudspeaker with 1" Dome tweeter, Vertical and horizontal mounting, 100V and low impedance connection possibility, Impedance 8 Ω, Max. Power 100 W, Sensitivity (1W/1m) 87 dB, RMS Power 50 W, Frequency Range (-10 dB) 55 Hz - 20 kHz, Response (± 3 dB) 70 Hz - 18 kHz, Dispersion angle H-110 Degree and V-110 Degree, Line Transformer Tapping 10W/20W/40W. Make: Sennheiser-Audac/ Martin/ Renkun Heinz

Amplifier for Green & Control Roomm Speakers:- SITC of Dual channel class D amplifier, RMS Power 150W @ 4 Ω Stereo, 300W @ 8 Ω Bridge and 80W @ 8 Ω, Signal / Noise > 90 dB, THD+N (@ 1 kHz) < 0.1% (1/2 Rated Power), Crosstalk (@ 1 kHz) > 70 dB, Operating, temperature 0° ~ 40° @ 95% Humidity, Frequency Response (± 3 dB) 20 Hz - 20 kHz, Inputs Sensitivity (1W/1m) 0 dB (1V RMS). Make: Sennheiser-Audac/ Martin/ Renkun Heinz

Digital Signal Processor:- SITC of Digital Signal processor having Quarter rack 1RU mainframe with eight user-configured card slots, 8 blank cards included, and built-in 4x4 I/O of Dante network audio. Integrated license-activated AEC. Dual core processing 40-bit floating DSP.Powered using PoE or included external power supply. Surface mount bracket included. Also 2 Input cards and 2 outputs card to be incoporate in the frame for making the processor 4 X 4. Make: Sennheiser-Xilica/ QSC/ Crestron

Touchpanel:- SITC of 8” programmable touch control, Display HD 1280 x 800 resolution, RJ 45 connector connectivity, mounts into a US 2-gang box or included low voltage bracket. Portrait or landscape orientation. PoE powered, external power supply not included. Make: Sennheiser-Xilica/ QSC/ Crestron

Mixer:- SITC of 32 Line Inputs (24 mono and 4 stereo) / 4 GROUP Buses + ST Bus / 6 AUX Sends + 2 FX Sends, FX1:REV-X(8 PROGRAM, PARAMETER control)/ FX2:SPX(16 PROGRAM, PARAMETER control), MIC: 24 (INPUTS HPF: 100Hz 12dB/oct), 48V phantom power per channel, USB Device, iPod / iPhone, THD 0.02% (20Hz-20kHz@ +14dBu), -128 dBu Equivalent Input Noise, -94 dBu Residual Output Noise, Cross Talk -74dB @ 1kHz. Power consumption 86W max. Make: Yamaha/ QSC/ Digico

Microphone:- SITC of The Handheld Set includes the handheld transmitter, stationary receiver and everything to use or install. Should come with rechargeable up to 15 hrs of operating time. Automatic frequency and interference management, Speech optimized condenser microphone capsule, Clear and easy focused user interface, Long operation time (up to 15 hours), Advanced power management and Li-Ion rechargeables, Secure 256 bit AES encryption, Remote controllable. Frequency response 20 to 20,000 Hz, Sound pressure level (SPL) 152 dB, THD, total harmonic distortion typ. 0.1, Transducer principle Condenser, Power consumption 350 mA, Signal-to-noise ratio > 90 dB(A), RF output power adaptive, up to 250 mW (country-specific), Operating time Accupack: typ. 15 h Operating time, Batteries: typ. 10 h, Power supply 12 V DC, Antenna connector 2 x reverse SMA, Audio output level (balanced) max. -18 dBu, typ. -24 dBu, Audio output level (unbalanced) max. +6 dBu, Dynamic range > 120 dB(A), Sensitivity 1,6 mV/Pa, Sampling rates 24 bit/48 kHz, Connection Audio out: XLR 3M Audio out: 2x RCA Connection Network: RJ 45, The Should have network enabled charging feature. Make: Sennheiser/ Audio technika/ Shure

Microphone :- SITC of Lavalier microphone includes the bodypack transmitter, stationary receiver and everything to use or install. The condensor lavalier microphone should come with rechargeable up to 15 hrs of operating time. Automatic frequency and interference management, Excellent speech intelligibility, Full, natural sound with low ambient noise, Automatic frequency and interference management, Lockable 3.5 mm jack socket, Secure 256 bit AES encryption, Frequency response 20 to 20,000 Hz, THD, total harmonic distortion typ. 0.1 %, Transducer principle Condensor, Power consumption 350 mA, Pick-up pattern omni-directional, Nominal impedance 1 kΩ, Signal-to-noise ratio > 90 dB(A), Equivalent noise level 27 dB, Maximum sound pressure level (passive) 143 dB, RF output power adaptive, up to 250 mW (country-specific) Power supply 12 V DC, Antenna connector 2 x reverse SMA, Current consumption approx. 240 μA, Audio output level (balanced) max. -18 dBu, typ. -24 dBu, Audio output level (unbalanced) max. +6 dBu, Dynamic range > 120 dB(A), Operating voltage (stand alone) 4,5 - 15 V, RF sensitivity < -90 dBm Sensitivity in free field, 5 mV/Pa ± 2.5 dB (at 1 kHz), Sampling rates 24 bit/48 kHz, Connection Audio Out: XLR 3M Audio Out: 2 x RCA Network: RJ 45. Make: Sennheiser/ Audio technika/ Shure

Microphone:- SITC of condensor headworn microphone, the Bodypack transmitter, stationary receiver and everything to use or install. Microphone should come with rechargeable accupacks with up to 15 hrs of operating time. The accupack is also USB rechargeable, the cable is in the box, the USB socket is presumably just a step away from you. The two types of sets are either Rackmount Sets (-R version), which come with everything needed for rack mounting, or Case Sets (-C version), in a transport case – without rackmounts, if you do not want to install the receiver, Frequency response 20 to 20,000 Hz, THD, total harmonic distortion typ. 0.1 %, Transducer principle Condensor, Power consumption 350 mA, Pick-up pattern omni-directional, Nominal impedance 1 kΩ Equivalent noise level 27 dB, Maximum sound pressure level (passive) 143 dB, RF output power adaptive, up to 250 mW (country-specific), Power supply 12 V DC, Antenna connector 2 x reverse SMA, Current consumption approx. 240 μA, Audio output level (balanced) max. -18 dBu, typ. -24 dBu, Audio output level (unbalanced) max. +6 dBu, Dynamic range > 120 dB(A), RF sensitivity < -90 dBm, Sensitivity in free field 5 mV/Pa ± 2.5 dB (at 1 kHz), Sampling rates 24 bit/48 kHz. Make: Sennheiser/ Audio technika/ Shure

Microphone:- SITC of The Digital Wireless Tablestand Set SL TS 133 GN Set DW includes the SL Tablestand, the gooseneck microphone, the SL Rack Receiver DW and everything needed for usage and installation. Qi Charging - most common wireless Charging standard, Compatibel with all Sennheiser XLR-3-gooseneck microphones, Clear battery life indication via dedicated battery status LEDs, Can be remote controlled with Sennheiser Control Cockpit. Frequency response 75 to 20,000 Hz THD, total harmonic distortion typ. 0.1 %, Power consumption 350 mA, Storage temperature-20 °C to 70 °C, (-4 °F to 158 °F) Operating temperature, 0 °C to 40 °C (14 °F to 131 °F), Signal-to-noise ratio > 90 dB(A)RF output power adaptive, up to 250 mW (country-specific), Operating time typ. 10h with BA 40, Power supply 12 V DC, Audio output level (balanced) max. -18 dBu, typ. -24 dBu Audio output level (unbalanced) max. +6 dBu, Dynamic range > 120 dB(A), Input impedance 30 kΩ, Max. Input voltage 1.7 V RMS, RF sensitivity < -90 dBm, Sampling rates 24 bit/48 kHz. Make: Sennheiser/ Audio technika/ Shure

Microphone:- SITC of Dynamic super-cardioid microphone for speech and vocals, Extended high frequency range 40 - 16000 Hz, Consistent sound quality (varying distances, moving off axis), Handles high sound pressure levels, Silent on/off switch, Isolates handling noise, hum compensating coil, Excellent feedback rejection, Rugged metal housing. Sensitivity in free field, no load (1kHz) 1,8 mV/Pa, Nominal impedance 350 Ω, Min. terminating impedance 1000 Ω. Make: Sennheiser/ Audio technika/ Shure

Mic Charging Unit:- SITC of network enabled charger featuring four indiviual charging bays. Each bay is combined with 4 LEDs to indicate the corresponding battery status of the mobile device. Also Seamless network integration, 4 individual charging bays, Battery status indication for each bay, Full remote control, Connector RJ45. Make: Sennheiser/ Audio technika/ Shure

Power Transmitter:- SITC of wireless power transmitter, which provides convenient wireless charging. Charging time On 5 h / off: 3 h, Max. Input voltage 12 V DC, Operating temperature 5 °C to 35 °C (41 °F to 95 °F). Make: Sennheiser/ Audio technika/ Shure

Bracket for Speakers:- Ceiling flying system is especially designed for mounting the Main Speaker and subwoofer. Using these mounting brackets, the top and bass cabinet can be flown and mounted on any ceiling, or other position, while aiming the loudspeakers into the desired angle. Connection board set angle plate 20°- 60°.Make: Sennheiser-Audac/ Martin/ Renkun Heinz

Supply & drawing of 2 Core X 2.5 Sqmm Cable for Speakers in existing conduit as required. Make:Klotz/ Beldon/ Audio Set

Supply & drawing of 2 Core Shielded Cable for connectings Microphones in existing conduit as required. Make:Klotz/ Beldon/ Audio Set

SITC of Stage box for all the monitors and microphone conectivity with a slot of Video connectivity.

Supply & Fixing of XLR Connectors for connecting speakers & mikes with amplifier

Supplying & Fixing of Floor Standing Network/Server Rack - 42U / 800w / 800d, with Heavy Duty Extruded Aluminium Frame for rigidity. Top cover with FHU provision. Top & Bottom cover with cable entry gland plates. Two pairs of 19” mounting angles with ‘U’ marking. Depth support channels - 3 pairs. With a Overall Weight Carrying Capicity of 500Kgs. Side Panels - 42U/800d Front MS Door Perforated honeycomb 42U/800w Rear MS Door Split Perforated honeycomb 42U/800wFan 90CFM 230V AC, 4” dia Castors with Brake (set of 4) Vertical Cable manager 80mmW 42U Shelf, Stationery 700mm N/W PDU 12Sockets 5/15Amps with MCB Mounting Hardware (Pkt. Of 20) earthing Kit 150mmH Cable manager 1U MS with Loops complete in all respect. Make-APC/APW/HEINRICH

VIDEO SYSTEM: SITC of professional Indoor Type, 9.7 m x 5.7 m , 3mm pixel Pitch or better based Indoor Direct View True Color LED Video Wall ,Video & Image Processor with atleast 4in/4out DVI ports, Galvanized Steel mounting structure duly powder coated in mat black/ approved shade. complete including warranty period of three years with 5% spares on site. Make: Christie, Planar, NEC

Supply, Installation, Testing & Commissioning of Free Standing/Floor Mounted Digital Podium built of 1.6mm CRCA Steel sheet, screw less chasis, polymer powder coated, Wooden Top, All directional wheels with lock, Display feature- Highly Sensitive, Built- in interactive Capacitive touch Monitor with Tilt facility, Screen size-22"(interactive type), Color LED, scratch resistant, antiglare & overlay tampered vandal resistant glass(3mm) , Space & technical provision for additional devices like laptop, Visualizer, keyboard, mouse etc .Approved Make-Make-AHA / TECPODIUM/ EAPL

Supply, Installation, testing & Commissioning of full HD PTZ Camera with Output resolution: Full HD 1080p, Frame rate: 60 Fps, 10X Optical Zoom,128 Presets, DVI-I out, Ethernet out, C-Video Out, Audio In, Camera Control Interface: RS-232/422 /Ethernet, Panning Angle: -170° to +170° or better, Tilting angle: -30° to +90° or better, Focal length: f= 5 to 50mm or better, Horizontal viewing angle: 56.5deg. or better, Aperture: F1.8 to 3.0 or better, Auto/Manual Gain control feature, Image Flip feature, Exposure control feature, Minimum Object distance: 100(wide) to 1000(tele)mm or better, white balance feature. Approved Make-Lumens/Sony/Axis

Supply, Installation, testing & Commissioning of Joystick Camera Controller: Joystick for PAN/Tilt/Zoom and Focusing of cameras. Approved Make-Lumens/Sony/Axis

Supply, Installation, testing & Commissioning of Recording & Streaming Media Processor with 6 Video Inputs : 2x HDMI/VGA & 4x RJ 45 and 2x Audio Inputs because the audio always goes from the record out of the mixer/DSP. From these 6 inputs, you can take any 4 to record an stream in a single frame. It has inbuilt storage of 1TB which can record upto 300-350 hours of recording within the machine and is expandable through external hard drive..Approved Make-Media Site/ Media Point/Lumens

Supply, Installation, testing & Commissioning of FHD Video Conference Systems having 1+5 Party connectivity on FHD Resolution from day 1(Inbuilt/External) i/c wireless remote control, 12x Optical zoom , 10x Digital Zoom Full HD PTZ Camera, having minimum 50 presets, Input for 3 More External cameras, Dual Microphone, 3 Video outputs, Inbuilt SD card/Pen Drive Recording feature, PC connectivity for presentation sharing, necessary hardware, software, license, programming complete etc as required at site. Make: Polycom/Sony/Lifesize

Supply, Installation, testing & commissioning of 10” in‐wall IP touch panel control system10” 1280x800 resolution, Android 7.1 OS with ReAX Core engine, One RS‐232, One RS‐485, Four figital I/O, Home button with room, status lighting (red, green, yellow), 10/100 LAN PoE, Auxiliary 12v along with in‐wall mounting box. complete as reqd.Make-Aurora/Crestron/AMX

Supplying Installation testing and Commissioning of 24 port 10/100/1000BASE-T POE ports and four GbE/10GbE SFP/SFP+ uplink ports, layer 3 from day1 having static & RIP ,stackable upto 10 switches, should support external redundant power supply, certified , each switch should be provided with stacking port/cable complete in all respect Approved Make-Juniper/Cisco/Extreme

SITC of HDMI & Control twisted pair Transmitter with Input: 1x HDMI, 1x RS232/485 IR(Controls) , Output: 1x Twisted pair/HD base T input on RJ45, supporting transmission of audio,video, controls and power upto minimum 70 mtrs or more. Upto 4K resolution support at various distance, remote powering feature, HDCP 2.2 compliant & EDID as per specifications complete etc. as required. Make-AMX/Extron/Crestron

SITC of HDMI & Control twisted pair Receiver with Input:1x Twisted pair/HDbaseT input on RJ45, Output:1x HDMI, 1x RS232/IR(Controls) , supporting reception of audio,video, controls and power upto minimum 70mtrs or more. Upto 4K resolution support at various distance ,remote powering feature,HDCP 2.2 compliant & EDID. as per specifications complete etc. as required. Make-AMX/Extron/Crestron

Supply, Installation, Testing & Commissioning of 4x4 HDMI Matrix switcher .Make-AMX/Extron/Crestron

Supply, Installation, Testing & Commissioning of HDMI Cables with connectors at both ends. Size 4.5 mtr of approved Make-Aurora/Crestron/AMX

SITC of 4−pair U/FTP (unshielded around foiled twisted pair, Quality Construction of 23AWG solid copper conductors are cabled together in an unshielded outer jacket, CAT6a Certified, Total Wires: 8, Drain Wire: Solid 23AWG tinned copper, Overall Shield Material: 100% aluminum foil, 25% overlap Conductor Color Code: White/blue, white/orange, white/green, white/brown, Min. Bend Radius: 35mm, Propagation Delay Skew: 45ns/100m max, Impedance: 100Ω, DC Resistance: 48Ω/km (13.8Ω/1000ft) nominal Max. resistance Unbalanced: 2%, Capacitance: 1.2pF/m max, Temperature: –20° to +70°C (–4° to 158°F) Makes: Kramer, Klotz, Bandridge

LIFT: Elevator in lift shaft of dimensions 2690mm x3000mm (W x D) 20 passenger/1360 Kg. MRL lift with variable voltage variable frequency drive having a speed of 1.5 metre/ sec and travel height of 13.7 m(approx.) with 4 Stops, 900mm Door Width, 2100 mm Height and Microprocessor based control suitable for operation on 415 V, 50 Hz, 3 phase A.C. electric supply as required and with automatic brakes testing within 24 hours and Wire rope as traction media

Elevator in lift shaft of dimensions 2000mm x2500mm (W x D) 13 passenger/884 Kg. MRL lift with variable voltage variable frequency drive having a speed of 1.5 metre/ sec and travel height of 21.6 m(approx.) with 6 Stops, 900mm Door Width, 2100 mm Height and Microprocessor based control suitable for operation on 415 V, 50 Hz, 3 phase A.C. electric supply as required and with automatic brakes testing within 24 hours and Wire rope as traction media

Elevator in lift shaft of dimensions 1800mm x1800mm (W x D) 8 passenger/544 Kg. MRL lift with variable voltage variable frequency drive having a speed of 1.6 metre/ sec and travel height of 22.05 m(approx.) with 7 Stops, 900mm Door Width, 2100 mm Height and Microprocessor based control suitable for operation on 415 V, 50 Hz, 3 phase A.C. electric supply as required and as per specifications.with automatic brakes testing within 24 hours and Wire rope as traction media

Elevator in lift shaft of dimensions 2000mm x2500mm (W x D) 13 passenger/884 Kg. MRL lift with variable voltage variable frequency drive having a speed of 1.6 metre/ sec and travel height of 22.05 m(approx.) with 7 Stops, 900mm Door Width, 2100 mm Height and Microprocessor based control suitable for operation on 415 V, 50 Hz, 3 phase A.C. electric supply as required and with automatic brakes testing within 24 hours and Wire rope as traction media

Addressable Fire Alarm System: Supply, Installation, Testing, commissioning of Intelligent Fire Alarm Control Panel 2 Loop card inbuild,198 Addressable points per loop, total addressable devices 396, Integrated PSU with Battery Charger, Requires network card additionally for networking

Supply, Installation, Testing, commissioning of Panel, Maximum 10 Loops Dual Processor, 8 loops with Networkable, No Loops Fitted, Requires loop card and network card additionally for networking , Zone Indication, Colour graphical LCD display, Integrated PSU with Battery Charger Brand : (MORLEY/FIRELITE/Apollo or equivalent as approved by the Deptt.)

Supply,Installation, testing and commissioning of Graphical user interface, with features like Audio and visual alerts, Floor plan system visualization , 3D idle/overview mode including mouse hover/click interaction , Sweeping animations, Programmable buttons and displays , Quick and intuitive to set up and use , Remote and multi-user access with defined credentials , Password and pin code protection , Network history view/search, Printable reports , Multi network supervision over TCP/IP. Multil levelled Security concept: An individually configurable, layered security concept prevents unauthorized access to the FADS and ensuring compliance with the standards of use.Remote access over TCP/IP and Ethernet through PC. Information from any location about the fire alarm system. Independence of place of the fire Alarm Control panel. Quick overview on the current system status by remote access, en54/ce certified. The software shall be compatible with the fire alarm system.Make: Schneider/ Copper/ Siemens

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supply, installation, testing & commissioning of intelligent plug in photo electric Multi Criteria Detectors having features like integral communication, dual LED for 360° viewing angle, walk test with address display etc. UL / LPCB approved, make : (HONEYWELL, MORLEY IAS or equivalent as approved by the Deptt.)

Supply, Installation, Testing, commissioning of Addressable / Convectional Beam Detector with Reflector Brand : (MORLEY/FIRELITE/Apollo or equivalent as approved by the Deptt.)

Supply, installation, testing & commissioning of Response Indicator to give visual indication of detection of smoke - RED colour LED for indication. make - (Agni Suraksha, or equivalent as approved by the Deptt.)System Sensor.

Supply, installation, testing & commissioning of intelligent plug in Thermal Detectors having features like integral communication, dual LED for 360° viewing angle, walk test with address display etc. UL / LPCB approved, :HONEYWELL or equivalent as approved by the Deptt.)

Supply, Installation, Testing, commissioning of Addressable Semi Flush Mounting Resettable (NonBreaking Glass) MCP, Supplied with Special Reset Tool BRAND : (MORLEY/FIRELITE/Apollo or equivalent as approved by the Deptt.)

Supply, Installation, Testing, commissioning of Addressable Wall Mounting Sounder / Hooter Cum Strobe Brand : (MORLEY/FIRELITE/Apollo or equivalent as approved by the Deptt.)

Supply, Installation, Testing, commissioning of Addressable Loop Isolator Brand : (MORLEY/FIRELITE/Apollo or equivalent as approved by the Deptt.)

Supply, installation, testing & commissioning of Control Module.UL / LPCB approved, make - (Honeywell , MORLEY IAS or equivalent as approved by the Deptt.) with housing box Model:200e-SMD.

Supply, installation, testing & commissioning of Monitor Module.UL / LPCB approved, make - Honeywell , MORLEY IAS or equivalent as approved by the Deptt. with housing box

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of intelligent interface unit BACnet/ Modbus protocol i.e. supplying communication links between building management system and fire alarm control panel complete as required.

Supply, Installation, Testing & Commissioning of 9 zone Vocall compact fire fighter panel for jacks connectivity, BS5839 Pt9 compliant, Monitored handset, Monitored supply and charger, 15 status LEDs, Full duplex system complete with all accessories as per specifications. Approvals: EN54 / CE.

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.

Supplying, installation, testing & commissioning of fire fighter phone jack complete as required.

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

Supply, testing & commissioning of 2c x 1.5 sq.mm fire survival armoured cable 600/1000 Volt rated with class-2 Copper conductor having crosslinkable low smoke zero halogen insulation as per BS EN 50363 and low smoke zero halogen (LSZH) inner & outer sheath. The cable should meet fire performance circuit integrity test as per BS EN 50200 & BS 6387 CWZ (950 Deg. C for 3 hours). The cable should be LPCB certified to EN 61034-2, EN 60754-1, BS EN 50200 & BS 6387 CWZ. Outer sheath should be in red colour with Anti-rodent & LSZH properties including end terminators, saddles, clamps with screws etc for fixing on wall/ceiling or on cable trays complete as required. Make INDIA IMPEX(FrTek), POLYCAB, PRYSMIAN, FINOLEX, Polymer Fusion

Supply, installation, testing & commissioning of Dual action pull station with addressable interface, built in bicolour LED with key reset facility & smooth dual action design.UL / LPCB listed. make : (HONEYWELL, MORLEY IAS or equivalent as approved by the Deptt.)

PUBLIC ADDRESS SYSTEM: Supply, Installation, testing and commissioning of ceiling mount broadband speaker, 5" full range driver, Steel front grill with flame retardant materials, built in Steel fire protection dome, Line transfer tapping : 6watt - 3watt, Frequency Response : 90 Hz - 18 kHz, Max Sound Pressure : 90dB, should be comply with EN 61000-4-3:2001, EN 61000-4-1:2001, EN 60065:98 etc complete required as per specifications. Make: AUDAC / AIM-LINE / MARTIN AUDIO / FOHNN

Supply,Installation, testing and commissioning of IP55 rated 2-way wall speaker, Max power : 60watt@8ohm, Sensitivity : 85dB, Crossover Frequency : 2.5KHz, LF driver : 3" or more, Frequency Range : 60 Hz - 20 kHz, Line Transformer Tappings : 20watt - 10watt, Max Sound Pressure : 100dB, Dispersion Horizontal : 100° or more, Vertical : 100° or more etc complete required as per specifications Make: AUDAC / AIM-LINE / MARTIN AUDIO / FOHNN

Supply, Installation, testing and commissioning of touch based paging station, should be table mount / wall mount both, resolution : 1280 x 800 or better, Connectors : RJ45 ethernet, Power : PoE, can be expandable to make 16channel in one screen, comes with super cardioid paging microphone etc complete required as per specifications. Make: Xilica / AIM-LINE / MARTIN AUDIO / FOHNN / BIAMP / Sennheiser

Supply, Installation, testing and commissioning of High power Hypex Class-D amplifier, High thermal efficiency, Integrated APC limiter, Transformer : Toroidal, Input connections : 4 x unbalanced on RCA with passthrough + 4 x balanced on euroblock, Input sensitivity : 0 dBV / 1 V or less, Input impedance : 22 kΩ, S/N ratio : >101 dB A weighted or better, THD : < 0.07 %, Frequency response : 50 – 20 kHz, Protection circuits : over current, over temperature, Channel separation : >68 dB @ 1 kHz, Power supply : 2Xswitching mode power supply, Cooling : temperature controlled fan, Bridged output power: 2x480W@100V etc complete required as per specifications. Make: AUDAC / AIM-LINE / MARTIN AUDIO / FOHNN

Supply, Installation, testing and commissioning of DVD Player, complete required as per specifications. Make: Samsung/LG/Sharp

Supply Installation testing and comisioning of 19-inch Equipment Rack with standardized frame or enclosure for mounting multiple PA controllers, CD player, Amplifiers etc modules. Size 24U.Make-APW/Rittal/VALRACK.

Supply, testing & commissioning of 2c x 1.5 sq.mm fire survival armoured cable 600/1000 Volt rated with class-2 Copper conductor having crosslinkable low smoke zero halogen insulation as per BS EN 50363 and low smoke zero halogen (LSZH) inner & outer sheath. The cable should meet fire performance circuit integrity test as per BS EN 50200 & BS 6387 CWZ (950 Deg. C for 3 hours). The cable should be LPCB certified to EN 61034-2, EN 60754-1, BS EN 50200 & BS 6387 CWZ. Outer sheath should be in red colour with Anti-rodent & LSZH properties including end terminators, saddles, clamps with screws etc for fixing on wall/ceiling or on cable trays complete as required. Make INDIA IMPEX(FrTek), POLYCAB, PRYSMIAN, FINOLEX, Polymer Fusion

ACCESS CONTROL SYSTEM: Supply, Installation, testing and commissioning of Surface mounted Networkable multiprocessor controlled 4 reader controller capable of controlling multiple readers (IN/OUT) alongwith TCP/IP connectivity complete as per specifications. Control panel housed in MS Powder Coated Cabinet with Tamper Switch, Complete with power supply unit for Controllers & Magnetic Locks as per specification

Supply, installation, testing and commissioning of Access Control Application Software for 64 Reader Capacity, and 2000 Card Holder Capacity, Basic GUI , TA Module with Alarm Module, T+ Module, 2-Nos Client Work Stations,Module for using SQL DB , -MULTI Site Module.

Supply Installation testing and Commissioning of Biometric Attendance Device fingerprint technology inside 1:10,000 user identification in 1 second,Anti-fraud features,Fake finger detection, duress finger, timed anti-pass back,Tough design,CPU: ARM® Cortex™-A9 core 1GHz.Linux Operating System, 1:N mode: 10,000 user (*3 templates each, including 1 duress),1:1 mode: 250,000 user IDs,1 Million transaction logs.Inputs/outputs: Wiegand In & Out,as per technical specification. Make-Morpfho/HID/Tyco

Supply, installation, testing and commissioning of UL Listed Smart Card Reader fwith compatible support of weigand output, 13.56 MHz technology platform and complies with the ISO 15693 / 14443A standard for contact less smart card technology. Card reader must be configurable to read encrypted ISO14443A sectors using standard or custom read keys for Sign OUT Terminal. should be compatible with HID format cards. Encryption,All RF data transmission between the card and reader should be encrypted using a secure algorithm. Industry-standard encryption techniques and advanced key management systems should be used to avoid the risk of compromised data or duplicated cards. The reader should have audio transducer to provide various tone sequences to signify access granted, access denied, power up and diagnostics. Visually impaired cardholders can easily distinguish between access granted and access denied. High-intensity light bar should provide a clear visual status indication in red, green or amber, even in bright sunlight. Make-HID/Tyco

Supply, testing and commissioning of Exit Push Button

Supply, testing and commissioning of iClass Smart card .Make-HID

Supply, installation, testing and commissioning of Single Leaf Electro Magnetic Lock of Suitable Capacity(Min 600 lbs). Make-Bel/Ncom/HID

Supply, installation, testing and commissioning of Double Leaf Electro Magnetic Lock of Suitable Capacity(Min 1200 lbs). Make-Bel/Ncom/HID

Supply and Fixing of ''U'' Bracket with Accessories. Make-Bel/Ncom/HID

Supply and Fixing of ''L'' Bracket with Accessories. Make-Bel/Ncom/HID

Supply, Fixing and Laying of 8 Core multi strand, copper, unarmoured Cable (between the every readers & the access controllers). Make-Vimco/Finolex/Polycab

Supply, Fixing and Laying of 2 Core x 1.5 Sq mm, multi strand, copper, unarmoured cable (between the controller and EM Lock/Request to exit button). Make-Vimco/Finolex/Polycab

LIGHTNING PROTECTION SYSTEM: Supply, fitting & fixing of Lighting Finial Arrestor made of 25 mm dia 300 mm long solid G.I. tube having 85 mm dia. single prong at top and 3 mm base plate at bottom complete with fitting & fixing with G.I. nuts & bolts on roof, RCC slab, top of column etc. as specified and directed by the deptt.

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

Supplying & laying of 25x5 mm size G.I. strips drawn on surface from earth electrode to Electrical switch gears, machineries etc complete with supply of G.I. nuts & bolts, screws etc including riveting, soldering & making necessary connection as approved, specified and directed by the deptt.

Supplying & laying of 25x6 mm size G.I. strips drawn on surface from earth electrode to Electrical switch gears, machineries etc complete with supply of G.I. nuts & bolts, screws etc including riveting, soldering & making necessary connection as approved, specified and directed by the deptt.

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Supplying & laying of 32x6 mm size G.I. strips drawn on surface from earth electrode to Electrical switch gears, machineries etc complete with supply of G.I. nuts & bolts, screws etc including riveting, soldering & making necessary connection as approved, specified and directed by the deptt.( 32 mm X 6 mm from earth electrode directly in ground as required.)

Supply, installation & testing of G.I. earth station with perforated 40 mm dia and 4.50 Metre long heady duty G.I. pipe with necessary 40 mm dia. G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement 300 mmx300 mmx6 mm hinged cover C.I. earth plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt .

EPABX System: Supply Installation, Testing and Commissioning of Server Based EPABX Fully Computerized IP System, SIP Compliant. Multi slot 19: U Rack Mountable 2U Rack Expandable upto 900 Ports Presently Configuration as Below Make-NEC/Avaya/Cisco /panasonic: CO Line 32Nos. PRI(30 Channel) 2 Nos. SIP Extension 64 Nos Digital Extension Circuits 64 Nos Analog Extension Circuits 704 Nos.

Supply Installation, Testing and Commissioning of EPABX System SIP Compliant. Wall/Rack Mountable,Expandable upto 128 Ports.and configured as for below Ports P & T(CO Trunk) Line 08 Nos. Digital Extension Circuit 08Nos Analog Extension ircuit 24 Nos

Supply Installation, Testing and Commissioning of Integrated Viocemail System 4 Level IVR software with 6 different languages and 4 time schedule(As per OEM).

Supply Installation Testing and Commissioning of Digital Phone (24Key+ 60-line DSS Console) Backlit keypad Hands-free, full duplex ,Headset support Easy to use soft keys/LCD prompts,Directory dialling,Navigation wheel,Call history,Backlit LCD screen,Bluetooth support (BCAZ),Security lock key XML open interface .Approved Make-NEC/Avaya/Cisco

Supply Installation Testing and Commissioning of 24Key Digital Phone Backlit keypad Hands-free, full duplex ,Headset support Easy to use soft keys/LCD prompts,Directory dialling,Navigation wheel,Call history,Backlit LCD screen,Bluetooth support (BCAZ),Security lock key XML open interface .Approved Make-NEC/Avaya/Cisco

Supply Installation Testing and Commissioning of Digital Phone 12 key display Backlit keypad Hands-free working Easy to use soft keys / LCD prompts on display model Directory dial key 1000 system, 1000 group, 10 personal, 600 phone book Conference key Wall mountable Message waiting indicator .Approved Make-NEC/Avaya/Cisco

Supply Installation Testing and Commissioning of Digital Phone 6 key display Backlit keypad Hands-free working Easy to use soft keys / LCD prompts on display model Directory dial key 1000 system, 1000 group, 10 personal, 600 phone book Conference key Wall mountable Message waiting indicator .Approved Make-NEC/Avaya/Cisco

Supply Installation, Testing and Commissioning of Analog CLI Phone with handsfree.Approved Make-Binatone/Beetel/Panasonic

Stage Curtain: Supplying installation of MAIN CURTAIN made out of velvet curtain cloth with horizontal sliding arrangement complete with fixing rails, brackets, sliding arrangement & motorised operation complete with runners, master runners, pullies, 3mm steel wire rope, 1 HP DC motor, 2nos. micro switches for auto stop, 3 nos push buttons for forward, reverse and stop positions. The curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900mm and should be stitched in double gathering Appx.

Supplying installation of CENTER CURTAIN- I made out of glazed cotton curtain cloth with horizontal sliding arrangement complete with fixing rails, brackets,sliding arrangements & motorised operation complete with runners, master runners, pullies,3mm steel wire rope, 1HP DC motor, 2 nos.micro switches for auto stop, 3nos. push buttons for forward, reverse and stop positions.The curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900mm and should be stitched in double gathering.

Supplying installation of REAR CURTAINmade out of glazed cotton cloth with horizontal sliding arrangement complete with fixing rails, brackets, sliding arrangement and motorised operation complete with runners, master runners, pullies, 3mm steel rope wire, 1HP DC motor, 2 nos. micro switches for auto stop, 3 nos. push buttons for forward, reverse and stop positions. The curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900mm. The curtain should be stitched in double gathering.

Supplying installation of CYCLORAMA CUM SCREEN :- Providing and fixing cyclorama screen in plastic perforated material. The screen to be fixed on tubular frame made out of 35mm dia MS pipe.

Supplying installation of WINGS :- Providing and fixing cloth wings made out of black glazed cotton cloth fixed on 6mm thick commercial plywood fixed on one side of MS 50mm x 25mmx 16G pipe wielded frame work. The pipe framework made out of 25mm x 50 mm pipe. c/c 900 x 900 fixed with overhead pivote track complete with duly painted on both framework.

Supplying installation of FRILLS :-Providing and fixing average frills made out of double gathering glazed cotton cloth to be installed above the stage on 28mm dia GI pipe a Size: 24000 [AV] x 2000[H]

Size : 21000 [AV] x 1000 [H]

Supplying installation of 50mm dia B class GI pipe to be hung from existing grid or roof structure for side wings, lighting bars.

Supply of winch operating suspension sets 30 Kg capacity 5 lines with 12m/10m barrel, 5 line blocks winch unit with handle and rachet, clew plate and steel wire rope winch mounting etc. Frill Bars

Lighting Bars

Set Bars

Stage Lighting : Supplying installation testing and commissioning of 1000W, 240 Volt, PAR Sealed Beam Light with CRC Sheet Metal and alluminium die casting, mat black color, yoke & clamp.Make: canara lighting or eqvt as approved by the Deptt.

Supplying installation testing and commissioning of 1000W Planoconvex Spot Light complete with 1000W Halogen Bipin CP-41 lamp, G-38 base socket, spherical anodised reflector, 150 mm dia Planoconvex lens, rear sliding knob, yoke, colour frame & suitable clamp.Make: canara lighting or eqvt as approved by the Deptt.

Supplying installation testing and commissioning of 1000 W Halogen light with mash & barndoor consisting of 2nos. single contact compressible holders, yoke, 1000W halogen tube & suitable clamp.Make: canara lighting or eqvt as approved by the Deptt.

Supplying installation testing and commissioning of 19 High quality, noise less RGBW LED PAR light 54 x 3W high bright LED with 8 channels, beam 25 degreem DMX 512, Auti master/slave, sound active.

Supplying installation testing and commissioning of 1000W Halogen Fresnel light consisting of 1000W Halogen Bipin T-11 lamp, 150mm dia imported fresenel lens, Imported socket, bottom sliding knob, yoke, colour lens, frame & suitable clamp. Make: canara lighting or eqvt as approved by the Deptt.

Supplying installation testing and commissioning of 500W Halogen Cyclorama Flood Light with 500W Halogen tube. Alluminium anodised reflector, 2 nos compressible recessed single contact holders,colour frame & suitable clamp.Make: canara lighting or eqvt as approved by the Deptt.

Supplying installation testing and commissioning of Programmable Digital Lighting Console 120 Dimmer Channel and 200 fixtures with 48 fader, 10 fader x 20 pages Make: Zero 88.

Supplying installation testing and commissioning of Cross connecting panel 192+192+48Way way having 4mm sheathed sockets fitted on the panel for interchanging the light circuits with the dimmers as desired. The connection can be made with patch cords having 4mm sheathed banana plugs at both the ends with 1 mtr. super flexible cable of 40 SWG. The patch panel has neutral & earth bar connection strip.Make: canara lighting or eqvt as approved by the Deptt.

Supply & Laying of 1.5 sqmm 3 Core Shilded wire

Supply & Laying of Cable tray 40 X 100 X16 swg painted.

Supply, Installation, Testing & Commissioning of Light socket box 4'' x 4'' with 15 AMP multi socket.

Supply, Installation, Testing & Commissioning of light Ladder of 25mm x 50mm M.S.Tube size (6'X2').

Supply, Installation, Testing & Commissioning of 50mm OD GI Pipe B.Class for lighting grid & lighting bar to be hang from top with support to clamps.

Supply, Installation, Testing & Commissioning of DMX Splitter 1 in 8 out

Supply, Installation, Testing & Commissioning of DMX cable for stage to control room

Supply, Installation, Testing & Commissioning of Direct Light point MCB Box with 16 Amp MCB 18way

Supply, Installation, Testing & Commissioning of DMX point box with dual XLR panel Mount

Shree Gautam Construction Co Ltd

M/s Macrocosm Builders