GE CHD T 98 2025 26

Taking down Cement plaster or cement lime plaster on brick or stone walls including raking out joints, hacking for key & scrubbing down with water etc complete including disposal of unserviceable rubbish outside cantt area all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) as in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work complete including disposal of unserviceable rubbish outside cantt area all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete including disposal of unserviceable rubbish outside cantt area all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames n.exc 1.5 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames exc 1.5 sqm but n.exc 4 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts etc complete all as specified and directed by Engineer-in-Charge.

Dismanting of mild steel of any description not otherwise provided for inany location and any position complete all as specified and directed by Engineer-in-Charge.

Taking down of cast iron soil waste or vent pipe 100 mm bore including all fittings like traps,bends,junctions etc from any situation complete all as specified and directed by Engineer-in-Charge.

Taking down of cast iron soil waste or vent pipe 75 mm bore including all fittings like traps,bends,junctions etc from any situation complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Cutting chases in stone wall, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring etc., and making good, cutting not exc 10 cm girth and complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work or stone/boulder masonary built in cement mortar incl all quions arches, pillar or any other descrption etc complete including disposal of unserviceable rubbish outside cantt area all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforeced) of any description and in any position complete including disposal of unserviceable rubbish outside cantt area all as specified and directed by Engineer in Charge.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets from any position complete including disposal of unserviceable rubbish outside cantt area all as specified and directed by Engineer in Charge.

Dismantlling plain or corrugated steel sheeting in roof coverings in any position complete including disposal of unserviceable fillets outside cantt area all as specified and directed by Engineer in Charge.

Dismantling timber scantlings as in rails, posts, rafters, purlins etc under 40 Sq cm in section from any situation complete all as specified and directed by Engineer in Charge.

Disconnecting existing tanks of capacity exc. 500 ltr & n. exc. 1000 ltr, setting aside and removing from site complete all as specified and directed by Engineer-in-Charge.

Broken stone hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete, all as specified.

25 mm thick Cement concrete (1:2:4) type B-0,using 12.5 mm graded mechanically crushed stone aggregate as in sub base of floor and pavings etc. complete all as specified and directed by Engineer-in-Charge.

75 mm thick, cement concrete type C-1, 1:3:6 using 40 mm graded stone aggregate, finished even & smooth without using extra cement, as in plinth protection, complete all as specified.Plinth protection shall be laid in 1:20 slope and joint filling sealed with bituminous sealing compound grade "A" .

Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed by Engineer In Charge.

RCC Cement concrete (1:2:4) type B-0,using 12.5 mm graded mechanically crushed stone aggregate as in slab, shelves supported on wall, complete all as specified and directed by Engineer-in-Charge.

Use & waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings , slab over manholes similar work; not exceeding 200mm thick (Horizontal or sloping) (rough finished flat surfaces of concrete), complete all as specified and directed by Engineer-in-Charge.

TMT steel bars 10mm dia and over, of grade Fe-500D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

First quality Non - skid coloured Ceramic tiles 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc. set and jointed with 4 mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade,hardener ,resin in the ratio of 8:1:2 laid over and inculding 15 mm thick screed in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

Vitrified ceramic tiles coloured Light shade (sctratch and stain resistant tiles) 10 mm thick (Square/rectangular) polished, area of each tiles exceeding 0.42 Sqm but not exceeding 1.0 Sqm, in floor,skirting etc set and jointed with 4 mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade,hardener ,resin in the ratio of 8:1:2 laid over and including 15mm thick screed bedding layer in CM (1:4) complete all as specified and directed by Engineer-in-Charge.

Glazed ceramic coloured tiles 600 x 300 x 8 mm thick on vertical surface such as skirting , dado etc. over and including 10 mm thick rendering in CM 1:4 thick set and jointed with 4 mm spacer and grouting the joint of wall with epoxy grout mix of organic coated filler of desired shade, hardener, resin in the ratio of 8:1:2 complete all as specified and directed by Engineer-in-Charge.

Machine cut Kota stone slab flooring 20-25 mm thick, laid over & including 15 mm thick screed bed in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified and directed by Engineer-in-Charge.

Machine cut Kota stone slab 20-25 mm thick as in skirting, dado and pillars etc , laid over & including 10 mm thick rendering in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified and directed by Engineer-in-Charge.

Granite jet black shade, 16 mm thick, (table rubbed and polished) in single piece (in one direction) machine cut, machine polished, bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 15 mm thick (average thickness) cement mortar (1:4) screed, as in cooking platform, shelves, RCC counters, window cills & similar situations, complete all as specified and directed by Engineer-in-Charge.

Brick work with sub class 'B' bricks, class designation 7.5, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

Rendering 10 mm thick in cement mortar 1:6, on fair faces of brick or concrete surfaces , trowelled to even and smooth surface without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick in cement mortar 1:4, on brick or concrete surfaces in two layers mixed with water proofing compound on top layer, trowelled to even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. NOTE: Water proofing compound shall be measured and paid separately.

Supply only liquid water proofing comound ISI Marked complete all as specified and directed.

Rendering 5 mm thick in cement mortar 1:3 as in ceiling/soffits of slabs/Chajja/ Sunshade finishing the plastered surface even & smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge.

Preparation of plastered or unplastered new surfaces of ceilings and applying three coats of white wash including preparation of surface complete all as specified and directed by Engineer-in-Charge.

Preparation of new external surfaces of walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces as per manufacturers instructions etc complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper on walls over and including a coat of primer and 1 mm wall care puty including preparation of surface complete all as specified and directed.

Factory made Pressed steel frames, confirming to IS, having profile 125 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and fixing only 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge. Note: Mild Steel butt hinges shall be measured and paid separately as supply only under relevant item.

Factory made Pressed steel frames, confirming to IS, having profile 105 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and fixing only 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge. Note: Mild Steel butt hinges shall be measured and paid separately as supply only under relevant item.

Solid PVC door frames of size 50mm x 47 mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube, and edges will be painted to match with printed sheet, supply & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

35 mm thick factory made glazed & Skeleton shutters of 2nd class Hardwood open rebated & prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size ofstiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2009) complete all as specified and directed by Engineer-in-Charge.

Factory made solid panels PVC shutters 30mm thick (styles) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strips of 20mm width stuck inside with solvent cement for styles & wood grain printed PVC sheet for to rail lock rail & bottom rail on either side & as gap inserted for top rail & bottom rail paneling of panel colour PVC sheet to be fitted in the MS frame welded/scaled to the stiles & rail with suitable PVC sheet beading & jointed together with solvent cement supply & fixing in the frame at site as per specification & drawing.

35 mm thick factory made Flush shutters, solid core construction, with particle core and plywood face panels, commercial type on both sides face covered with decorative face veneer with lipping/frame to match with 1 mm thick mica supplied and fixed complete all as specified and directed by Engineer-in-Charge.

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators,casements/sliding shutters and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with rawl plugs and screws or with fixing clips or with expansion hold fastener of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall not be less than 2 mm thick,smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling. C.P. brass/ stainless steel screws,hinges/pivot and making provision for fixing of fittings wherever required complete all as specified and directed by Engineer-in-Charge. Note :1. The rate is inclusive of rollers,locks,rubber beading,rubber seal etc for sliding/casement shutters required for satisfactory operation of window/ventilator/door. 2. Panel fillings other than aluminium filling and necessary fittings shall be measured and paid for separately

Powder coated aluminium grill dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge

Stainless steel butt hinges 100 mm long heavy weight complete all as specified and directed by Engineer-in-Charge.

Stainless steel handle D type with back plate and fixed with screws of size 150 mm complete all as specified and directed by Engineer-in-Charge..

Aluminium alloy, anodised, hasp staple (bolt type) 100 mm long hinge pin including fixing with bolts fixed in repair complete all as specified and directed by Engineer-in-Charge.

150 mm long Aluminium anodised barrel tower bolts of extruded section complete all as specified and directed by Engineer-in-Charge.

Mild steel sliding door bolts 300 mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified & directed by Engineer in Charge.

Mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats et conforming to Fe-410 W(Gde E-250) quality B complete all as specified and directed by Engineer-in-Charge.

Mild Steel Framed work as in guard bars/grills, gratings, etc.. with ends of bars shouldered/welded and/or riveted, or forged into spikes; framed guard bars/grills conforming to Fe-290 (Gde E-165) complete all as as specified and directed by Engineer-in-Charge.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

Sheet glass 5.5 mm thick, ordinary quality and glazing with linseed oil pane putty & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares exceeding 0.5 Sq. mtr in each pane, complete all as specified and directed by Engineer-in-Charge.

5.0 mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm each and using Silicon for fixing of glass in addition to glazing putty complete all as specified and directed by Engineer-in-Charge.

Preparation of new or previously untreated wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

Preparation of old or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

19mm thick plywood BWR type BB, fixed with screws to timber frame work as in kitchen cabinets , cupboards etc, fixed in repair with both sided covered with 1 mm thick mica with lipping / frame to match complete as specified and directed by Engineer-in-Charge.

Continuous (piano hinges) 30mm width of flap in repairs Paino hinges SS Gde-304 (width of flap 30mm) complete all as specified and directed by Engineer-in-Charge.

Door strip ( snake Guard) minimum 18 mm wide aluminium body and nylon brushes 22 mm wide fixed with screws complete all as specified and directed by Engineer-in-Charge.

Chromium Plated health faucet 2 in 1 including 1 mtr long flexible tube with hook complete all as specified and directed by Engineer-in-Charge'.

Supplying and fixing in repairs waste pipe 32 mm dia flexible for Sink and WHB complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge. Make:- Jaquar: CON-107KN, Somany: 272210150011, Cera: F2006152

Supplying and fixing in repairs fancy type stop valves/Angle valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated with long shank and cup complete all as specified and directed by Engineer-in-Charge. Make:-Jaquar:CON-059KN, Somany: 272210270041, Cera: F2006201.

Supplying and fixing in repairs stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated with long shank and cup (Concealed type) complete all as specified and directed by Engineer-in-Charge. Make:-Jaquar: CON: 083FTR & ALD083FT, Somany: 272210150041 & 272150610011, Cera: F2006351 & F4050102.

Supplying and fixing fancy type shower rose 125mm dia size of Rim and 30cm long CP brass pipe with swiwel joint in including fixing to steel pipe or union complete all as specified and directed by Engineer-in-Charge.

Supply and fixed in repair brass chromium plated, tubular towel rail, 20mm dia, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge.

PVC connections 15mm size with brass chromium nuts of length 450mm fixed in repair complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs vitreous china Pedestal type wash hand basin white flat back of size 550x440mm including CI brackets , chromium plated waste coupling, waste pipe etc., (incl all waste fittings) complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair PVC cabinet with mirror for bathroom 540X340X130mm, fancy type, white or colour complete all as specified and directed by Engineer-in-Charge

Supply and fixed in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste pipe incl bedding in cement mortor to dwarf wall ot cantilever brackets and connecting union to pipe overall size 495x420mm, bowl size 410x 330x160mm incl all fittings ie chromium plated waste coupling, waste pipe complete all as specified and directed by Engineer-in-Charge.

Stainless steel plate rack of standard size 600mmx900 mm x 250 mm complete and fixing with rawl plug and steel screws of weight upto 8/10 kg fixed in repair complete all as specified and directed by Engineer in Charge.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm bore fixed in repair complete all as specified and directed by Engineer in Charge.

75mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches, floors & fixed to walls with and including MS clamps made out of flat iron of size 25 mm x 3 mm including nuts,bolts complete all as specified and directed by Engineer-in-Charge.

110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches, floors & fixed to walls with and including MS clamps made out of flat iron of size 25 mm x 3 mm including nuts,bolts complete all as specified and directed by Engineer-in-Charge.

PVC(SWR) bends (any radius), for 75 mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

PVC(SWR) bends (any radius), for 110mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.,Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including providing and fixing prepainted Gypsum Board tiles for insulation 7mm thick in ceilingof size 60 cm x 60 cm fixed for grid size 605 x 605 mm with screw as per manufacturers instructions complete all as specified and as directed by the Engineer-in-Charge.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directed by Engr-in-charge.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in ridges, fascia, valleys, gutters etc. fixed with self tapping screws etc complete all as specified and as directed by Engr-in-charge.

CPVC(SDR-11) of outer dia 20 mm with and including CPVC SDR-11 fittings on walls and ceilings or laying in floors complete all as specified and directed by Engineer-in-Charge.

CPVC(SDR-11) of outer dia 25 mm with and including CPVC SDR-11 fittings on walls and ceilings or laying in floors complete all as specified and directed by Engineer-in-Charge.

Supply and fixed in repair Brass chromum plated mixer for mixing hot and cold water fancy type with screwed down for 15mm dia iron pipe complete all as specified and directed by Engineer-in-Charge. Make:- Jaquar:- CON-167KNB, Somany:- 272200150051, Cera:F2006461.

Supply & fixing 15 mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed. complete all as specified and directed by Engineer-in-Charge.

Material and labour water proofing treating to Roof and sunken portion and adjoining walls of kitchen, WC, Bath & toilet etc complete all as specified under :- (a) M&L for applying bituminous primer @ 0.40 litre per sqm over clean dry roof surface including parapete/sunken floor. (b) Applying a coat of blown bitumen 85/25 grade @ 1.2 Kg/sqm over priming coat torching over laps with a propane or butan gas torch. (c) M&L for providing and laying 3mm thick APP modified polymer reinforced water proofing membrane with minimum weight of 3.60 Kg/sqm as specified. (d) The APP membrane shall be laid using torch application with minimum 10cm side overlap and 15cm end overlap. (e) The app shall be fixed with termination bar and fastners and end shall be properly sealed with sealent. (f) The rain water gutter or spout pipe portion shall be finished with cement mortar 1:4 to provide requisite slope towards outlet.

M&L for PCC (1:5:10), using 40mm graded stone aggregates, using Liquied water proofing compound @ 200ml per 50 kg weight of cement as in padding concrete to sunken floor, Coving/ gola to junbction of the floor and vertical walls including chamfering on edges, complete all as specified and directed. Note:- supply only waterproofing compound shall be measured and paid separately.

Steel water tubes, 50 mm bore, medium grade, galvanized, as in spout for sunken floor, fixed in wall, inside end fixed with wire netting and external beveled edge at 45 degree, complete all as specified and directed by Engineer - in -Charge.

Stainless steel cutlery pan SS 304 grade basket of any description/pattern as approved by GE ,fixed with sliding channel,revolving wheels fixed with screws to timber frame work in kitchen cabinets,cupboards etc fixed in repairs complete all as specified and directed by Engineer-in-Charge.

120 mm long Stainless steel handles, Fancy type,fixed with stainless steel screws to timber frame work in kitchen cabinets,cupboards etc complete all as specified and directed by Engineer-in-Charge.

Stainless steel auto closing hinges (DADA) ,fixed with stainless steel screws to PVC/Wooden moulded shutters frame work in kitchen cabinets,cupboards etc complete all as specified and directed by Engineer-in-Charge.

Stainless steel innotech channel soft close 400-500 mm long fixed with stainless steel screws to PVC/Wooden moulded shutters frame work in kitchen cabinets,cupboards etc complete all as specified and directed by Engineer-in-Charge. Make:- Godrej, Hettich india, EBCO.

Supply and fixing corner glass shelf 225x225mm shall be 6 mm thick toughened glass with a polished edge. The frame shall be cinstructed of 25mm cp brass tubing with a bruched finish. Shelves shall be supported by adjusable shelf supports and have a wright capacity of 15 kg. The unit shall be installed using appropriate anchors for the wall type complete all as specified and directed by Engineer-in-charge. Make:-Jaquar: CPA CHR 1173,Somany: 272130120011,Cera: F5005102.

100mm Anti-Cockroach floor drain grating with detachable trap, designed to prevent entry of cockroaches, insects and foul smell, suitable for bathrooms, kitchens, balconies and utility areas, complete all as specified and directed.

375 mm, ordinary rat tail rod pattern springs including roller and roller plate fixed in repair complete all as specified and directed by Engineer-in-Charge.

20-25mm dia curtain rod of Harrison rails,mild steel chromium plated wall thickness 0.9 mm including bracket,stops,rollerswith decorative balls/caps at both ends of rod complete all as specified and directed by Engineer-in-Charge.

Supply and fixing ball catcher for cupbords and kitchen cabinets incl both male & female part making each set, complete all as specified and directed.

Material & Labour for treatment of efflorescence to walls affected by capillary action and moisture ingress, including identification of affected areas, removal of loose salts by dry brushing/ scraping, thorough surface cleaning, and washing with clean water or taking down completely old plaster or any type of treatment. Applying approved anti-efflorescence/ water-repellent chemical treatment masonry. The work includes sealing of cracks, joints, and honeycombed areas with approved polymer-modified mortar or injection grout wherever required, surface neutralization, and drying prior to treatment. Treatment shall be applied by brush/ roller/ spray in multiple coats as per manufacturer’s specifications, ensuring effective penetration and complete coverage. The rate includes preparation, protection of adjoining surfaces, curing/ drying time, and completion of the work, complete as directed by the Engineer-in-Charge

INTERNAL ELECTRIC SUPPLY WORKS

Taking down old unserviceable light fittings any type and removal from site and making good disturbed surfaces of walls, ceiling etc complete all as specified and directed by Engineer-in-Charge to match with existing surface all as directed.

Taking down MCB DB/ Meter box of any size and removal from site and making good disturbed surfaces complete all as specified and directed.

Same all as per item No 106, above but controlled by two way switch

Same all as per item No 106, One 3 pin 5 Amps socket outlet on independent board

Same all as per item No 106, One 3 pin 5 Amps socket outlet on same board with other switches

Same all as per item No 106, One bell/buzzeer point controlled by one bell push.

Modular snap Switch one way 6 Amps one module complete all as specified and directed.

Modular snap Switch one way 16 Amps one module complete all as specified and directed.

Modular snap Switch two way 6 Amps one module complete all as specified and directed.

Modular Bell Push 6 Amps one module complete all as specified and directed.

Modular Socket 6/16Amps 5 Pin 2 Module complete all as specified and directed.

Modular Socket 5/6Amps 5 Pin 2 Module complete all as specified and directed.

Modular blanking plate suitable for 1 Module complete all as specified and directed

Modular fan Regulator step electronic type 2 module complete all as specified and directed.

Ceiling rose surface backlite 65 x 20mm size three terminalcomplete all as specified and directed.

Electric bell AC, ding-dong type, 230 Volt, single pole complete all as specified and directed.

Lamp holder, PVC/ Polycarbonate type with back plate with and including one no of LED bulb 15 watt Base-22 retrofit type complete all as specified & directed.

LED lights fitting 1x 20 Watt, 220V,AC decorative box type,aluminium body with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose including 20 watt LED tube rod complete all as specified and directed.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Security Light LED 60 Watt made up of pressure dia cast Alumunium housing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including sevice bracket of GI pipe 32mm bore medium grade of length 0.9 mtr with MS clamps, bolts, nuts, and washers and suitable reducer for connecting fitting to GI pipe as required as site and making electrical connection, complete all as specified and directed.

Distribution Board double door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, MCB DB 12 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc flushed on the existing wall , to match with existing surface and making all necessary connections complete all as specified and directed.

Distribution Board double door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, 4 way TPN, 415 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc flushed on the existing wall , to match with existing surface and making all necessary connections complete all as specified and directed.

ISOLATOR TPN 63 Amps, 415 volts complete all as specified and directed.

ISOLATOR DP 63 Amps, 230 volts complete all as specified and directed.

ISOLATOR SP 6- 40 Amps, 220 volts , 50 Hzs, 10 KA , "C" series, ISI marked all as specified and directed.

Earthing complete with and including galvanised steel earth plate electrode 60 mm x 60 mm x 6 mm surrounded by a mixture of charcoal and salt in alternate layers burried directly in ground vertically in a pit of depth not less than 2.25 m deep below ground level with top edge of earth plate at a depth of not less than 1.5 m below ground level, connected with and including galvanised iron or steel earth wire, 4mm dia (No. 8 SWG) by means bolts, nuts, check nuts and washers made out of galvanised iron, 15 mm bore (light grade) GI pipe for protection of earthing lead, 20 mm bore (light grade) GI pipe for watering with funnel, wire mesh and including necessary excavation and earth work, PCC 1:2:4 type B-1 pit and 50 mm thick RCC M-25(Design mix) reinforced with XPM (weight not less than 3 kg/sq m) pit cover, C.I frame, charcoal and comman salt filling in alternate layers, complete all as shown and specified in electrical plate No. 3 of SSR Part-I (2009) complete all as shown on drawings and as specified and directed by Engineer-in-Charge. Note : The unit rate includes for protecton pipe 15mm and GI earth strip 4mm from top of earth plate upto 7.50 metre above ground level.

Sub main wiring using approved colour coding as per IS with two runs of 4 sqmm PVC insulated, unsheathed cable FRLSH, flame retardant low smoke and low halogen 1100 volts grade , ISI marked with multistranded copper conductor with one run of 4 sqmm (green colour) PVC insulated, unsheathed cable FRLSH, flame retardant low smoke and low halogen 1100 volts grade , ISI marked with multistranded copper conductor as earth wire connected to common earth dolly with thimbles, drawing into & including PVC Concealed conduit ISI marked with all accessories on walls and making good of disturbed surfaces including all conduit fittings, clamps, gutties etc all as specified and directed. Note: (i) Three runs ( main ) of 4.00 sqmm cable together with conduit shall be considered as 1 running meter for payment purpose.

M&L in replacement of sheet metal enclouser to accommodate 04 Nos electric meters of size 800 mm X 500 mm X 150 mm deep and 1.6 mm thick MS sheet, powder coated, bakelite sheet with hung shutter including provision of locking arragement and niche covered with 4 mm thick plain glass, including locking arrangement & open wiring coverd with flexible PVC pipe of suitable size complete all as specified and directed.

Exhaust fan 250 mm sweep metal body, heavy duty, Single phase AC 230/240V, with energy efficient motor, pre lubricated double ball bearing, speed 1200 rpm complete with louvers for wall mounting including grouting,making hole in the wall (Square/Round) as feasible grouting and holding down bolts, nuts, washers and provision of flexible copper conductor cable 3 core from ceiling rose to exhaust fan incl cutting of hole of required size for fixing of the exhaust fan complete all as specified and directed

Note: For the purpose of arriving at lumpsum amount, the amount of credit schedule i.e Sch 'A' section II (i.e Rs 1,17,567.84 shall be deducted from the total amount arrived.

Total of Schedule 'A' Rs.

Please Enable Macros to View BoQ information