TVC Division- (A) Improvements to Divisional Railway Hospital/TVP (B)Renovation of Operation theatre.

Vol-I & Vol- II ) except reinforcement steel.)

Item- 1 SW (I) Improvements to DRH/TVP SW I (a) :Improvements to second floor

S No. Item No Description of Item Unit Qty Rate Amount

5.0 REINFORCEMENT CEMENT CONCRETE

5.1S CAST IN SITU

5.3 Reinforced cement concrete work in beams, cum 15 11505.5 172582.5

suspended floors, roofs having slope up to 15

degree landings, balconies, shelves, chajjas,

lintels, bands, plain window sills, staircases

and spiral stair cases above plinth level up to

1 floor five level, excluding the cost of centering,

shuttering, finishing and reinforcement with

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)

derived from natural sources : 3 graded stone

aggregate 20 mm nominal size derived from

natural sources).

5.9S FORM WORK

Centering and shuttering including strutting,

propping etc. and removal of form for

5.9.3 Suspended floors, roofs, landings, balconies Sqm 77 927.25 71398.25

and access platform

5.9.5 Lintels, beams, plinth beams, girders, Sqm 200 736.4 147280

bressummers and cantilevers

6.0 MASONRY WORK

6.1S General

Brick work with common burnt clay F.P.S. (non

modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V

level in all shapes and sizes in :

6.12S HALF BRICK MASONRY

Half brick masonry with common burnt clay

F.P.S. (non modular) bricks of class designation

7.5 in superstructure above plinth level up to

THIRUVANANTHAPURAM DIV-ENGG/SOUTHERN RLY

6.26S EXPOSED BRICK WALL

6.47 Providing and laying Autoclaved Aerated cum 170 8333.65 1416720.5

Concrete (AAC) blocks masonry with 150 mm

to 300 mm thick with Grade -1 AAC blocks of

density 551 to 650 kg/cum conforming to IS:

2185 (Part 3) in super structure above plinth

7 level up to floor V level with RCC band at sill

level and lintel level with approved block

laying polymer modified adhesive mortar all

complete as per direction of Engineer-in-

Charge. (The payment of RCC band and

reinforcement shall be made for separately).

8.0 CLADDING WORK

8.1S General

Stone work (machine cut edges) for wall lining

etc. (veneer work) upto10 metre height,

backing filled with a grout of average 12 mm

thick cement mortar 1:3 (1 cement : 3 coarse

sand) including pointing in white cement

mortar 1:2 (1 white cement : 2 stone dust)

with an admixture of pigment matching the

stone shade : (To be secured to the backing

and the sides by means of cramps and pins

which shall be paid for separately) :

White sand stone - exposed face fine dressed

with rough backing .

8.20S STONE WORK DRY CLADDING

8.31 Providing and fixing Ist quality ceramic glazed Sqm 40 1267.95 50718

wall tiles conforming to IS: 15622 (thickness to

be specified by the manufacturer), of approved

make, in all colours, shades except burgundy,

bottle green, black of any size as approved by

9 Engineer-in-Charge, in skirting, risers of steps

and dados, over 12 mm thick bed of cement

mortar 1:3 (1 cement : 3 coarse sand) and

jointing with grey cement slurry @ 3.3kg per

sqm, including pointing in white cement mixed

with pigment of matching shade complete.

9.0 WOOD AND P.V.C. WORK

9.1S FRAMES AND TRUSSES

Providing wood work in frames of doors,

windows, clerestory windows and other

frames, wrought framed and fixed in position

with hold fast lugs or with dash fasteners of

required dia & length (hold fast lugs or dash

fastener shall be paid for separately).

Providing and fixing panelled or panelled and

glazed shutters for doors, windows and

clerestory windows, fixing with butt hinges of

9.5 required size with necessary screws, excluding

panelling which will be paid for separately, all

complete as per direction of Engineer-in-

9.5.1 Second class teak wood

Extra for providing heavy sheet float glass

panes instead of ordinary float glass in glazed

doors, windows and clerestory window

shutters. (Area of opening for glass panes

excluding portion inside rebate shall be

12 per sqm) instead of 4 mm thick (weight not

less than 10 kg per sqm).

THIRUVANANTHAPURAM DIV-ENGG/SOUTHERN RLY

9.12 Extra for providing frosted glass panes 4 mm Sqm 3 176.4 529.2

thick (weight not less than 10 kg per sqm)

instead of ordinary float glass panes 4 mm

thick (weight not less than 10 kg per sqm) in

doors, windows and clerestory window

shutters. (Area of opening for glass panes

excluding portion inside rebate shall be

Deduct for not providing hinges in doors,

windows or clerestory window shutters with :

ISI marked M.S. pressed butt hinges bright

9.15.2 finished of required size with necessary

9.15.2.1 For 2nd class teak wood and other class of Sqm 100 -59.8 -5980

9.40S MISCELLANEOUS-WOOD WORK

Providing and fixing M.S. grills of required

pattern in frames of windows etc. with M.S.

9.48 flats, square or round bars etc. including

priming coat with approved steel primer all

9.48.2 Fixed to openings /wooden frames with rawl Kg 100 238.35 23835

plugs screws etc.

COPER OXIDISED MILD STEEL FITTINGS

(COPPER OXIDISED AS PER IS: 1378)

Providing and fixing ISI marked IS: 1341

oxidised M.S. pressed Parliamentary hinges

with necessary screws etc. complete (Copper

oxidised as per IS 1378)

Providing and fixing ISI marked oxidised M.S.

door latches conforming to IS:5930 with

screws etc. complete (Copper oxidised as per

Providing and fixing ISI marked oxidised M.S.

handles conforming to IS:4992 with necessary

screws etc. complete (Copper oxidised as per

9.72S BRASS FITTINGS

Providing and fixing bright finished brass tower

9.74 bolts (barrel type) with necessary screws etc.

9.76 Providing and fixing bright finished brass 100 Each 10 854.65 8546.5

mm mortice latch and lock with 6 levers and a

pair of lever handles of approved quality with

necessary screws etc. complete.

Providing and fixing special quality bright

finished brass cupboard or ward robe locks

with four levers of approved quality including

necessary screws etc. complete.

9.80 Providing and fixing 50 mm bright finished Each 60 74.25 4455

22 brass cup board or wardrobe knob of approved

quality with necessary screws.

Providing and fixing bright finished brass

handles with screws etc. complete:

9.82 Providing and fixing bright finished brass Each 10 121.65 1216.5

24 hanging type floor door stopper with necessary

screws, etc. complete.

THIRUVANANTHAPURAM DIV-ENGG/SOUTHERN RLY

9.83 Providing and fixing aluminium die cast body Each 10 1124.85 11248.5

tubular type universal hydraulic door closer

(having brand logo with ISI, IS : 3564,

embossed on the body, door weight upto 35 kg

and door width upto 700 mm), with necessary

accessories and screws etc. complete.

Providing and fixing bright finished brass

9.86 casement stays (straight peg type) with

necessary screws etc. complete :

9.88S CHROMIUM PLATED BRASS FITTINGS

9.88 Providing and fixing chromium plated brass Each 10 998.35 9983.5

100 mm mortice latch and lock with 6 levers

and a pair of lever handles of approved quality

with necessary screws etc. complete.

9.89 Providing and fixing chromium plated brass Each 10 952.8 9528

28 night latch of approved quality including

necessary screws etc. complete.

9.105S GYPSUM BOARD PARTITIONS

Providing and fixing partition upto ceiling

height consisting of G.I. frame and required

board, including providing and fixing of frame

work made of special section power pressed/

roll form G.I. sheet with zinc coating of 120

gms/sqm(both side inclusive),consisting of

floor and ceiling channel 50mm wide having

equal flanges of 32 mm and 0.50 mm thick,

fixed to the floor and ceiling at the spacing of

610 mm centre to centre with dash fastener of

12.5 mm dia meter 50 mm length or suitable

anchor fastener or metal screws with nylon

plugs and the studs 48 mm wide having one

flange of 34 mm and other flange 36 mm and

0.50 mm thick fixed vertically within flanges of

floor and ceiling channel and placed at a

spacing of 610 mm centre to centre by 6 mm

dia bolts and nuts, including fixing of studs

along both ends of partition fixed flush to wall

with suitable anchor fastener or metal screws

with nylon plugs at spacing of 450 mm centre

to centre, and fixing of boards to both side of

frame work by 25 mm long dry wall screws on

studs, floor and ceiling channels at the spacing

of 300 mm centre to centre. The boards are to

be fixed to the frame work with joints

staggered to avoid through cracks, M.S. fixing

channel of 99 mm width (0.9 mm thick having

two flanges of 9.5 mm each) to be provided at

the horizontal joints of two boards, fixed to the

studs using metal to metal flat head screws,

including jointing and finishing to a flush finish

with recommended jointing compound,

jointing tape, angle beads at corners (25 mm x

25mm x 0.5 mm), joint finisher and two coats

of primer suitable for board as per

manufacture's specification and direction of

engineer in charge all complete.

9.105.1 75 mm overall thickness partition with 12.5 Sqm 10 2131.1 21311

mm thick double skin fire rated Glass

29 Reinforced Gypsum (GRG) plaster board

conforming to IS: 2095: part 3 (Board with BIS

certification marks)

Providing and fixing magnetic catcher of

approved quality in cupboard / ward robe

shutters, including fixing with necessary

screws etc. complete.

THIRUVANANTHAPURAM DIV-ENGG/SOUTHERN RLY

9.115 Providing and fixing powder coated telescopic ONE 10 414.2 4142

drawer channels 300 mm long with necessary SET

screws etc. complete as per directions of

Engineer- in-charge.

Providing and fixing factory made uPVC door

frame made of uPVC extruded sections having

an overall dimension as below (tolerance +/-

1mm), with wall thickness 2.0 mm ( +/- 0.2

mm), corners of the door frame to be Jointed

with galvanized brackets and stainless steel

9.117 screws, joints mitred and Plastic welded. The

hinge side vertical of the frames reinforced by

galvanized M.S. tube of size19 X 19 mm and

1mm ( +/- 0.1 mm) wall thickness and 3 nos.

stainless steel hinges fixed to the frame

complete as per manufacturer's specification

and direction of Engineer- in-charge

32 9.117.1 Extruded section profile size 48x40 mm Metre 75 270.2 20265

9.118 Providing and fixing to existing door frames.

9.118.3 25 mm thick PVC flush door shutters made out Sqm 43 3068.85 131960.55

of a one piece Multi chamber extruded PVC

section of the size of 762 mm X 25 mm or less

as per requirement with an average wall

thickness of 1 mm ( +/- 0.3 mm). PVC foam

end cap of size 23x10 mm are provided on

both vertical edges to ensure the overall

thickness of 25 mm. M.S. tube having

dimensions 19 mm x 19 mm and 1.0 mm ( +/-

0.1 mm) is inserted along the hinge side of the

33 door. Core of the door shutter should be filled

with High Density Polyurethane foam. The Top

& Bottom edges of the shutter are covered

with an end-cap of the size 25 mm X 11 mm.

Door shutter shall be reinforced with special

polymeric reinforcements as per

manufacturer's specification and direction of

Engineer-in-charge to take up necessary

hardware and fixtures. Stickers indicating the

locations of hardware will be pasted at

appropriate places

9.121 Providing and fixing Fiber Glass Reinforced Metre 50 570.95 28547.5

plastic (FRP) Door Frames of cross-section 90

mm x 45 mm having single rebate of 32mm x

15 mm to receive shutter of 30 mm thickness.

The laminate shall be moulded with fire

resistant grade unsaturated polyester resin

and chopped mat. Door frame laminate shall

be 2 mm thick and shall be filled with suitable

wooden block in all the three legs. The frame

shall be covered with fiber glass from all sides.

M.S. stay shall be provided at the bottom to

steady the frame.

9.122 Providing and fixing to existing door frames.

9.122.2 30 mm thick Fiberglass Reinforced Plastic Sqm 20 4488.95 89779

(F.R.P.) flush door shutter in different plain and

wood finish made with fire retardant grade

unsaturated polyester resin, moulded to 3 mm

thick FRP laminate all around, with suitable

wooden blocks inside at required places for

35 fixing of fittings and polyurethane foam

(PUF)/Polystyrene foam to be used as filler

material throughout the hollow panel, casted

monolithically with testing parameters of

F.R.P. laminate conforming to table - 3 of IS:

14856, complete as per direction of Engineer-

THIRUVANANTHAPURAM DIV-ENGG/SOUTHERN RLY

Providing & Fixing decorative high pressure

laminated sheet of plain / wood grain in gloss /

matt/ suede finish with high density protective

9.127 surface layer and reverse side of adhesive

bonding quality conforming to IS : 2046 Type

S, including cost of adhesive of approved

Providing and fixing fly proof stainless steel

grade 304 wire gauge, to windows and

clerestory windows using wire gauge with

average width of aperture 1.4 mm in both

directions with wire of dia. 0.50 mm all

Providing and fixing factory made uPVC

glazed/wire mesh windows/ doors comprising

of lead free uPVC multi-chambered frame, sash

and mullion/coupler (where ever required)

extruded profiles having minimum wall

thickness of 1.70 mm for Series R1 and R2

profiles and 2.10 mm for Series R3 and R4

profiles conforming to EN: 12608 in any shape,

colour and design duly reinforced with

galvanized mild steel section made of required

shape & size as per CPWD Specification, uPVC

extruded glazing beads, interlocks and Inline

sash adaptor (where ever required) of

appropriate dimension, EPDM gasket,

hardware, SS 304 grade fasteners of minimum

8 mm dia with countersunk head, comprising

of matching polyamide PA6 grade sleeve for

fixing frame to finished wall as per IS 1367 :

Part 1 to 14, plastic packers, plastic caps and

necessary stainless steel screws etc. Profile of

frame, sash & mullion (if required) shall be

mitred cut and fusion welded/mechanically

jointed duly sealed at all corners, including

drilling of holes for fixing hardware and

drainage of water etc. After fixing frame the

gap between frame and adjacent finished wall

shall be filled with weather proof silicon

sealant over backer rod of approved size and

quality, all complete as per approved drawing

conforming to CPWD specification & direction

of Engineer-in-Charge. Section of steel

reinforcement and cross sections of uPVC

profiles to be as per design approved by

Engineer-in-Charge. Wire mesh / Glazing of

plain/ toughened/ laminated/ double glass unit

with / without high performance coatings as

per design requirements and conforming to IS:

3548 & IS: 16231 shall be paid separately.

Three track three panels sliding window with

9.147.A5 Aluminium channel for roller track, wool pile,

nylon rollers with SS 304 body

9.147.A5.2 Using R3 series with frame (98 mm & above) x Sqm 50 8543.6 427180

(40 mm & above) & sash (30 mm & above) x

(55 mm & above) with zinc alloy (zamak)

powder coated handle on two end panels

along with multi-point locking system (Height

upto 1.8 metre).

Casement Window with Double Rebate Frame

with two Side Hung Glazed Panel and two Side

Hung wire mesh Panel and Fixed Mullion with

9.147.E7 S.S. 304 friction hinges as per size and weight

of sash, multi-point locking system, zinc alloy

(zamak) powder coated handles on both

glazed and fly screen panel

THIRUVANANTHAPURAM DIV-ENGG/SOUTHERN RLY

9.147.E7.1 Using R3 series with frame (110mm & above) Sqm 13 20576.3 267491.9

x (45mm & above) & glazed sash (55mm &

above) x (65mm & above) & fly screen sash

39 (30mm & above) x (55mm & above) & mullion

(55mm & above) x (65mm & above) & metal

grill (if required to be paid separately). (Height

upto 1.8 meter)

Casement Door with Double Rebate Frame

with one Side Hung Glazed Panel and one Side

Hung wire mesh Panel with zinc alloy (zamak)

3D hinges, multi-point locking system with

9.147.F3 cylinder, zinc alloy (zamak) powder coated

handles on both sides of glazed panel and zinc

alloy (Zamak) powder coated handle along

with multi-point locking system on one side of

fly screen panel.

9.147.F3.1 Using R3 series with frame (110mm & above) Sqm 13 19994.4 259927.2

x (45mm & above) & glazed sash (55mm &

40 above) x (85mm & above) & fly screen sash

(55mm & above) x (65mm & above). (Height

upto 2.5 meter).

Providing and fixing stainless steel (SS-304

grade) friction hinges to the side/top hung

9.148 uPVC windows, of approved quality, with

necessary stainless steel screws etc. as per

direction of Engineer-in-charge.

9.155 Providing and fixing panelling or panelling and Sqm 50 1956.9 97845

glazing in panelled or panelled and glazed

shutters for doors, windows and clerestory

windows ( area of opening for panel inserts

excluding portion inside grooves or rebated to

be measured). Panelling for panelled and

glazed shutters 25mm to 40mm thick: Pre-

laminated with decorative lamination on both

side exterior Grade - I MDF Board12 mm thick

confirming to IS:14587

9.171 Providing and fixing stainless steel soft closing Each 5 272 1360

spring hinges at 0 degree hinges (hydraulic

type) of approved make/brand to cupboard

43 shutters with full threaded steel screws

including making necessary recess in board

and finished etc. complete as per direction of

Engineer-in-charge.

9.172 Providing and fixing stainless steel soft closing ONE 20 885.1 17702

heavy type telescopic drawer channels of SET

44 approved make 500 mm long with screws etc.

complete as per directions of Engineer- in-

10.0 STEEL WORK

10.1S General

10.2 Structural steel work riveted, bolted or welded Kg 100 133.7 13370

in built up sections, trusses and framed work,

45 including cutting, hoisting, fixing in position

and applying a priming coat of approved steel

primer all complete.

Steel work in built up tubular (round, square or

rectangular hollow tubes etc.) trusses etc.,

including cutting, hoisting, fixing in position

and applying a priming coat of approved steel

primer, including welding and bolted with

special shaped washers etc. complete.

11.0 FLOORING

11.41S VITRIFIED FLOOR TILES

THIRUVANANTHAPURAM DIV-ENGG/SOUTHERN RLY

Providing and laying Vitrified tiles in floor in

different sizes (thickness to be specified by the

manufacturer) with water absorption less than

0.08% and conforming to IS:15622, of

approved brand & manufacturer, in all colours

and shade, laid on 20 mm thick cement mortar

1:4 (1 cement: 4 coarse sand) jointing with

11.41A grey cement slurry @3.3 kg/sqm including

grouting the joints with white cement and

matching pigments etc. The tiles must be cut

with the zero chipping diamond cutter only .

Laying of tiles will be done with the notch

trowel, plier, wedge, clips of required

thickness, leveling system and rubber mallet

for placing the tiles gently and easily.

11.41A.2 Glazed vitrified floor tiles polished finish of size

11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size

Providing and laying Vitrified tiles in different

sizes (thickness to be specified by the

manufacturer), with water absorption less than

0.08% and conforming to IS: 15622, of

approved brand & manufacturer, in all colours

11.47 and shade, in skirting, riser of steps, laid with

cement based high polymer modified quick set

tile adhesive (water based) conforming to IS:

15477, in average 6 mm thickness, including

grouting of joints (Payment for grouting of

joints to be made separately).

Grouting the joints of flooring tiles having

joints of 3 mm width, using epoxy grout mix of

0.70 kg of organic coated filler of desired

11.48 shade (0.10 kg of hardener and 0.20 kg of

resin per kg), including filling / grouting and

finishing complete as per direction of

Engineer-in-charge.

12.0 ROOFING

12.37S RAIN WATER SPOUT AND PIPE

Providing and fixing on wall face unplasticised

Rigid PVC rain water pipes conforming to IS :

13592 Type A, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap

for thermal expansion, (i) Single socketed

Providing and fixing unplasticised -PVC pipe

clips of approved design to unplasticised - PVC

rain water pipes by means of 50x50x50 mm

hard wood plugs, screwed with M.S. screws of

required length, including cutting brick work

and fixing in cement mortar 1:4 (1 cement : 4

coarse sand) and making good the wall etc.

THIRUVANANTHAPURAM DIV-ENGG/SOUTHERN RLY

Providing and fixing false ceiling at all height

including providing and fixing of frame work

made of special sections, power pressed from

M.S. sheets and galvanized with zinc coating of

120 gms/sqm (both side inclusive) as per IS :

277 and consisting of angle cleats of size 25

mm wide x 1.6 mm thick with flanges of 27

mm and 37 mm, at 1200 mm centre to centre,

one flange fixed to the ceiling with dash

fastener 12.5 mm dia x 50 mm long with 6

mm dia bolts, other flange of cleat fixed to the

angle hangers of 25x10x0.50 mm of required

length with nuts & bolts of required size and

other end of angle hanger fixed with

intermediate G.I. channels 45x15x0.9 mm

running at the spacing of 1200 mm centre to

centre, to which the ceiling section 0.5 mm

thick bottom wedge of 80 mm with tapered

flanges of 26 mm each having lips of 10.5 mm,

at 450 mm centre to centre, shall be fixed in a

direction perpendicular to G.I. intermediate

channel with connecting clips made out of 2.64

mm dia x 230 mm long G.I. wire at every

junction, including fixing perimeter channels

0.5 mm thick 27 mm high having flanges of 20

mm and 30 mm long, the perimeter of ceiling

fixed to wall/partition with the help of rawl

plugs at 450 mm centre, with 25mm long dry

wall screws @ 230 mm interval, including

fixing of gypsum board to ceiling section and

perimeter channel with the help of dry wall

screws of size 3.5 x 25 mm at 230 mm c/c,

including jointing and finishing to a flush finish

of tapered and square edges of the board with

recommended jointing compound , jointing

tapes , finishing with jointing compound in 3

layers covering upto 150 mm on both sides of

joint and two coats of primer suitable for

board, all as per manufacturer's specification

and also including the cost of making openings

for light fittings, grills, diffusers, cutouts made

with frame of perimeter channels suitably

fixed, all complete as per drawings,

specification and direction of the Engineer in

Charge but excluding the cost of painting with

12.45.1 12.5 mm thick tapered edge gypsum plain Sqm 300 1355.8 406740

53 board conforming to IS: 2095- (Part I) :2011

(Board with BIS certification marks)

12.50 Providing and fixing precoated galvanised iron Sqm 1400 738.65 1034110

profile sheets (size, shape and pitch of

corrugation as approved by Engineer-in-

charge) of total coated thickness 0.50 mm

(base metal of minimum 0.45 mm thickness

with total coating thickness of 0.05 mm) with

zinc coating 120 grams per sqm as per IS: 277,

in 240 mpa steel grade, 5-7 microns epoxy

primer on both side of the sheet and polyester

top coat 15-18 microns. Sheet should have

54 protective guard film of 25 microns minimum

to avoid scratches during transportation and

should be supplied in single length upto 12

metre or as desired by Engineer-in-charge. The

sheet shall be fixed using self drilling /self

tapping screws of size (5.5x 55 mm) with

EPDM seal, complete upto any pitch in

horizontal/ vertical or curved surfaces,

excluding the cost of purlins, rafters and

trusses and including cutting to size and shape

wherever required.

THIRUVANANTHAPURAM DIV-ENGG/SOUTHERN RLY

Providing and fixing precoated galvanised steel

sheet roofing accessories of total coated

thickness 0.50 mm (base metal of minimum

0.45 mm thickness with total coating thickness

of 0.05 mm) with Zinc coating 120 grams per

sqm as per IS: 277, in 240 mpa steel grade, 5-

7 microns epoxy primer on both side of the

sheet and polyester top coat 15-18 microns

using self drilling/ self tapping screws

13.0 FINISHING

13.1S CEMENT PLASTER (IN FINE SAND)

13.1 12 mm cement plaster of mix :

13.3 20 mm cement plaster of mix :

13.20S PEBBLE DASH PLASTER

13.26 Providing and applying plaster of paris putty of Sqm 960 262.7 252192

2 mm thickness over plastered surface to

prepare the surface even and smooth

13.44S EXTERIOR FINISHING

Finishing with Deluxe Multi surface paint

13.48 system for interiors and exteriors using Primer

as per manufacturers specifications :

13.48.1 Two or more coats applied on walls @ 1.25 Sqm 1920 193.7 371904

60 ltr/10 sqm over and including one coat of

Special primer applied @ 0.75 ltr /10 sqm

13.48.2 Painting wood work with Deluxe Multi Surface Sqm 500 176.25 88125

Paint of required shade. Two or more coat

61 applied @ 0.90 ltr/10 sqm over an under coat

of primer applied @0.75 ltr/10 sqm of

approved brand and manufacture

13.48.3 Painting Steel work with Deluxe Multi Surface Sqm 500 170.7 85350

Paint to give an even shade. Two or more coat

62 applied @ 0.90 ltr/10 sqm over an under coat

of primer applied @ 0.80 ltr/10 sqm of

approved brand and manufacture

13.50 Applying priming coat:

13.50.3 With ready mixed red oxide zinc chromate Sqm 250 67.4 16850

63 primer of approved brand and manufacture on

steel galvanised iron/ steel works

Painting with synthetic enamel paint of

13.61 approved brand and manufacture to give an

Varnishing with varnish of approved brand and

65 13.113.1 One or more coats with copal varnish Sqm 200 94.6 18920

13.114 Melamine polishing on wood work (one or Sqm 200 138.1 27620

14.0 REPAIRS TO BUILDING

14.26S WOOD WORK

14.34 Providing and fixing 150 mm bright finished Each 10 271.45 2714.5

floor brass door stopper with rubber cushion,

necessary brass screws etc. to suit shutter

thickness complete

Providing and fixing bright finished brass hard

drawn hooks and eyes :

15.0 DISMANTLING AND DEMOLISHING

THIRUVANANTHAPURAM DIV-ENGG/SOUTHERN RLY

15.1S General

Dismantling steel work in single sections

15.17 including dismembering and stacking within 50

metres lead in:

15.18 Dismantling steel work in built up sections in Kg 5000 5.65 28250

angles, tees, flats and channels including all

70 gusset plates, bolts, nuts, cutting rivets,

welding etc. including dismembering and

stacking within 50 metres lead.

17.0 SANITARY INSTALLATIONS

17.1S General

Providing and fixing water closet squatting pan

(Indian type W.C. pan ) with 100 mm sand cast

Iron P or S trap, 10 litre low level white P.V.C.

flushing cistern, including flush pipe, with

17.1 manually controlled device (handle lever)

conforming to IS : 7231,with all fittings and

fixtures complete, including cutting and

making good the walls and floors wherever

17.1.1 White Vitreous china Orissa pattern W.C. pan Each 1 6767.4 6767.4

71 of size 580x440 mm with integral type foot

Providing and fixing white vitreous china

pedestal type water closet (European type

W.C. pan) with seat and lid, 10 litre low level

white P.V.C. flushing cistern, including flush

17.2 pipe, with manually controlled device (handle

lever), conforming to IS : 7231, with all fittings

and fixtures complete, including cutting and

making good the walls and floors wherever

17.2.1 W.C. pan with ISI marked white solid plastic Each 6 6515.55 39093.3

Providing and fixing white vitreous china flat

back or wall corner type lipped front urinal

basin of 430x260x350 mm and 340x410x265

mm sizes respectively with automatic flushing

17.4 cistern with standard flush pipe and C.P. brass

spreaders with brass unions and G.I clamps

complete, including painting of fittings and

brackets, cutting and making good the walls

and floors wherever required :

17.4.1 One urinal basin with 5 litre white P.V.C. Each 3 6258.75 18776.25

automatic flushing cistern

Providing and fixing wash basin with C.I.

brackets, 15 mm C.P. brass pillar taps, 32 mm

17.7 C.P. brass waste of standard pattern, including

painting of fittings and brackets, cutting and

making good the walls wherever require:

17.7.2 White Vitreous China Wash basin size 630x450 Each 5 2226.35 11131.75

mm with a single 15 mm C.P. brass pillar tap

Providing and fixing P.V.C. waste pipe for sink

17.28 or wash basin including P.V.C. waste fittings

17.28.2 Flexible pipe

17.31 Providing and fixing 600x450 mm bevelled Each 10 1607.95 16079.5

edge mirror of superior glass (of approved

76 quality) complete with 6 mm thick hard board

ground fixed to wooden cleats with C.P. brass

screws and washers complete.

THIRUVANANTHAPURAM DIV-ENGG/SOUTHERN RLY

Providing and fixing PTMT towel rail complete

with brackets fixed to wooden cleats with CP

brass screws with concealed fittings

arrangement of approved quality and colour.

17.73.1 450 mm long towel rail with total length of 495 Each 10 673.4 6734

77 mm, 78 mm wide and effective height of 88

mm, weighing not less than 170 gms

18.0 WATER SUPPLY

18.7S C.P.V.C. PIPES

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal stability

for hot & cold water supply, including all CPVC

plain & brass threaded fittings and fixing the

pipe with clamps at 1.00 m spacing. This

includes jointing of pipes & fittings with one

step CPVC solvent cement and the cost of

cutting chases and making good the same

including testing of joints complete as per

direction of Engineer in Charge. Concealed

work, including cutting chases and making

good the walls etc.

18.49S C.P. BRASS FITTINGS

Providing and fixing C.P. brass bib cock of

approved quality conforming to IS:8931 :

Providing and fixing C.P. brass angle valve for

18.53 basin mixer and geyser points of approved

quality conforming to IS:8931

18.59S AIR VALVE & WATER METER (BULK TYPE)

18.64 Providing and fixing PTMT swivelling shower, Each 10 121.4 1214

81 15 mm nominal bore, weighing not less than

18.65 Providing and fixing PTMT soap Dish Holder Each 10 111.45 1114.5

having length of 138mm, breadth 102mm,

82 height of 75mm with concealed fitting

arrangements, weighing not less than 106

19.0 DRAINAGE

19.1S STONE WARE PIPES AND FITTINGS

19.33 Constructing soak pit 1.20x1.20x1.20 m filled Each 1 2890.1 2890.1

with brick bats including S.W. drain pipe 100

mm diameter and 1.20 m long complete as

per standard design.

21.0 ALUMINIUM WORK

21.1S General

Providing and fixing aluminium work for doors,

windows, ventilators and partitions with

extruded built up standard tubular sections/

appropriate Z sections and other sections of

approved make conforming to IS: 733 and IS:

1285, fixing with dash fasteners of required

dia and size, including necessary filling up the

gaps at junctions, i.e. at top, bottom and sides

with required EPDM rubber/ neoprene gasket

etc. Aluminium sections shall be smooth, rust

free, straight, mitred and jointed mechanically

wherever required including cleat angle,

Aluminium snap beading for glazing /

panelling, C.P. brass / stainless steel screws,

all complete as per architectural drawings and

the directions of Engineer-in-charge. (Glazing,

panelling and dash fasteners to be paid for

21.1.1 For fixed portion

THIRUVANANTHAPURAM DIV-ENGG/SOUTHERN RLY

21.1.1.2 Powder coated aluminium (minimum thickness Kg 40 530.9 21236

of powder coating 50 micron)

For shutters of doors, windows & ventilators

including providing and fixing hinges/ pivots

and making provision for fixing of fittings

wherever required including the cost of EPDM

rubber / neoprene gasket required (Fittings

shall be paid for separately)

21.1.2.2 Powder coated aluminium (minimum thickness Kg 40 634.45 25378

of powder coating 50 micron)

Providing and fixing glazing in aluminium door,

window, ventilator shutters and partitions etc.

with EPDM rubber / neoprene gasket etc.

21.3 complete as per the architectural drawings

and the directions of engineer-in-charge . (Cost

of aluminium snap beading shall be paid in

21.3.2 With float glass panes of 5 mm thickness Sqm 5 1505.25 7526.25

(weight not less than 12.50 kg/sqm)

26.0 NEW TECHNOLOGIES AND MATERIALS

26.1S General

26.11 Providing and fixing concealed hinge of Each 50 144.05 7202.5

87 approved quality for 19-20 mm thick door with

stainless steel screws complete :

26.28S REPAIR AND REHABILITATION ITEMS

Drilling suitable holes in reinforced or plain

cement concrete with power driven drill

machine to a minimum depth of 100 mm upto

200 mm in RCC beams, lintels, columns and

slabs to introduce steel bars for

sunshades/balconies including fixing the steel

bars in position using epoxy resin anchor grout

of approved make but excluding the cost of

reinforcement, all complete as per direction of

Engineer-In-Charge.

26.73S PREFAB/PRECAST TECHNOLOGY

Providing and fixing factory made single

extruded WPC (Wood Polymer Composite)

solid board one side white color and other side

of board laminted with PVC foil of minimum 14

micron thickness of approved design pasted

with hot melt adhesive for cup boards, work

stations and bathroom/kitchen cabinet etc. of

required sizes comprising of virgin polymer of

K value 58-60 (Suspension Grade), calcium

carbonate and natural fibers (wood powder/

rice husk/wheat husk) and non toxic additives

(maximum toxicity index of 12 for 100 gms)

having minimum density of 650 kg/cum and

screw withdrawal strength of 1800 N (Face) &

900 N (Edge), minimum compressive strength

50 N/mm2, modulus of elasticity 850 N/mm2

and resistance to spread of flame of Class A

category with property of being termite/borer

proof, water/moisture proof and fire retardant

and fixing with stainless steel piano hinges/soft

close clip on concealed hinges of required size

with necessary full body threaded star headed

counter sunk S.S screws, all as per direction of

Engineer-In- Charge.

Item- 2 SW (I) Improvements to DRH/TVP SW I(b):Rain water harvesting

S No. Item No Description of Item Unit Qty Rate Amount

2.0 EARTH WORK

THIRUVANANTHAPURAM DIV-ENGG/SOUTHERN RLY

2.1S General

Earth work in excavation by mechanical means

(Hydraulic excavator)/manual means over

areas (exceeding 30 cm in depth, 1.5 m in

2.6 width as well as 10 sqm on plan) including

getting out and disposal of excavated earth

lead upto 50 m and for all lift, as directed by

Engineer-in-charge.

Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means in

foundation trenches or drains (not exceeding

1.5 m in width or 10 sqm on plan), including

dressing of sides and ramming of bottoms, for

all lift, including getting out the excavated soil

and disposal of surplus excavated soil as

directed, within a lead of 50 m.

12.0 ROOFING

12.37S RAIN WATER SPOUT AND PIPE

Providing and fixing on wall face unplasticised

Rigid PVC rain water pipes conforming to IS :

13592 Type A, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap

for thermal expansion, (i) Single socketed

23.0 RAIN WATER HARVESTING & TUBEWELLS

23.1S General

23.5 Supplying, filling, spreading & leveling stone cum 4 1509.8 6039.2

boulders of size range 5 cm to 20 cm, in

4 recharge pit, in the required thickness, for all

leads & lifts, all complete as per direction of

Engineer-in-charge.

23.6 Supplying, filling, spreading & leveling gravels cum 3 1538.25 4614.75

of size range 5 mm to 10 mm, in the recharge

pit, over the existing layer of boulders, in

required thickness, for all leads & lifts, all

complete as per direction of Engineer-in-

23.7 Supplying, filling, spreading & leveling coarse cum 2.5 1538.25 3845.63

sand of size range 1.5 mm to 2 mm in

6 recharge pit, in required thickness over gravel

layer, for all leads & lifts, all complete as per

direction of Engineer -in-charge.

Item- 3 SW II :Renovation of Operation theatre

S No. Item No Description of Item Unit Qty Rate Amount

2.0 EARTH WORK

2.1S General

Earth work in excavation by mechanical means

(Hydraulic excavator)/manual means over

areas (exceeding 30 cm in depth, 1.5 m in

2.6 width as well as 10 sqm on plan) including

getting out and disposal of excavated earth

lead upto 50 m and for all lift, as directed by

Engineer-in-charge.

4.0 CONCRETE WORK

4.1S CEMENT CONCRETE (CAST IN SITU)

Providing and laying in position cement

concrete of specified grade excluding the cost

of centering and shuttering - All work up to

THIRUVANANTHAPURAM DIV-ENGG/SOUTHERN RLY

derived from natural sources : 4 graded stone

aggregate 20 mm nominal size derived from

natural sources)

6.0 MASONRY WORK

6.1S General

Brick work with common burnt clay F.P.S. (non

modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V

level in all shapes and sizes in :

10.0 STEEL WORK

10.1S General

10.2 Structural steel work riveted, bolted or welded Kg 100 133.7 13370

in built up sections, trusses and framed work,

4 including cutting, hoisting, fixing in position

and applying a priming coat of approved steel

primer all complete.

Steel work in built up tubular (round, square or

rectangular hollow tubes etc.) trusses etc.,

including cutting, hoisting, fixing in position

and applying a priming coat of approved steel

primer, including welding and bolted with

special shaped washers etc. complete.

13.0 FINISHING

13.1S CEMENT PLASTER (IN FINE SAND)

13.1 12 mm cement plaster of mix :

13.44S EXTERIOR FINISHING

Wall painting with acrylic emulsion paint,

having VOC (Volatile Organic Compound )

content less than 50 grams/ litre, of approved

brand and manufacture, including applying

additional coats wherever required, to achieve

even shade and colour.

Painting with synthetic enamel paint of

13.99 approved brand and manufacture of required

colour to give an even shade :

Finishing walls with Acrylic Smooth exterior

paint of required shade :

13.111.2 Old work (One or more coat applied @ 0.90 Sqm 50 80.65 4032.5

15.0 DISMANTLING AND DEMOLISHING

15.1S General

Dismantling doors, windows and clerestory

windows (steel or wood) shutter including

chowkhats, architrave, holdfasts etc. complete

and stacking within 50 metres lead :

Dismantling wood work in frames, trusses,

purlins and rafters up to 10 metres span and 5

metres height including stacking the material

within 50 metres lead :

15.14.1 Of sectional area 40 square centimetres and cum 1 4459.1 4459.1

15.57 Dismantling aluminium/ Gypsum partitions, Sqm 50 56.35 2817.5

doors, windows, fixed glazing and false ceiling

12 including disposal of unserviceable material

and stacking of serviceable material with in 50

meters lead as directed by Engineer-in-charge.

THIRUVANANTHAPURAM DIV-ENGG/SOUTHERN RLY

18.0 WATER SUPPLY

18.7S C.P.V.C. PIPES

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal stability

for hot & cold water supply, including all CPVC

plain & brass threaded fittings and fixing the

pipe with clamps at 1.00 m spacing. This

includes jointing of pipes & fittings with one

step CPVC solvent cement and the cost of

cutting chases and making good the same

including testing of joints complete as per

direction of Engineer in Charge. Concealed

work, including cutting chases and making

good the walls etc.

21.0 ALUMINIUM WORK

21.1S General

Providing and fixing aluminium work for doors,

windows, ventilators and partitions with

extruded built up standard tubular sections/

appropriate Z sections and other sections of

approved make conforming to IS: 733 and IS:

1285, fixing with dash fasteners of required

dia and size, including necessary filling up the

gaps at junctions, i.e. at top, bottom and sides

with required EPDM rubber/ neoprene gasket

etc. Aluminium sections shall be smooth, rust

free, straight, mitred and jointed mechanically

wherever required including cleat angle,

Aluminium snap beading for glazing /

panelling, C.P. brass / stainless steel screws,

all complete as per architectural drawings and

the directions of Engineer-in-charge. (Glazing,

panelling and dash fasteners to be paid for

21.1.1 For fixed portion

21.1.1.3 Polyester powder coated aluminium (minimum Kg 1 539.85 539.85

14 thickness of polyester powder coating 50

Providing and fixing glazing in aluminium door,

window, ventilator shutters and partitions etc.

with EPDM rubber / neoprene gasket etc.

21.3 complete as per the architectural drawings

and the directions of engineer-in-charge . (Cost

of aluminium snap beading shall be paid in

21.3.2 With float glass panes of 5 mm thickness Sqm 1 1505.25 1505.25

(weight not less than 12.50 kg/sqm)

Providing and fixing aluminium tubular handle

bar 32 mm outer dia, 3.0 mm thick & 2100

mm long with SS screws etc .complete as per

direction of Engineer-in-Charge.

21.12.1 Anodized (AC 15 ) aluminium tubular handle Each 1 575.75 575.75