Loading…
Loading…
Tender Value
₹1.9 Cr
EMD Value
₹3.7 L
Closing Date
4 Sept 2026, 3:00 pm
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
DEN/1/KIR
20 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-XIVA, of STD/June/22 along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet
Technical Eligibility Criteria as under (Document in support of Technical Eligibility Criteria should be submitted/uploaded as per Anneuxre-V of tender document) :
(a)The tenderer must have successfully completed or substantially completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or One similar work each costing not less than the amount equal to 60% of advertised value of the tender.
(b)(i) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender.
Note for para 1.2 above: Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components.
(b) (ii) In such cases, what constitutes a component in a composite work shall be clearly predefined with estimated tender cost of it, as part of the tender documents without any ambiguity.
Note for Standard Technical Criteria: Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered atleast 5 years prior to the date of closing of tender, shall also be considered provided the work 1.4.1 experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
(b)(iii) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Note: for subletting of work costing up to Rs 50 lakh, no previous work experience of subcontractor shall be asked for by the Railway. In case after award of contract or during execution of work it becomes necessary for contractor to change subcontractor, the same shall be done with subcontractor(s) fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract, with prior approval of Chief Engineer in writing
Defination of Similar Work :- Any Building works with framed structure.
47 conditions · 11 needing a document upload
" No post tender correspondence will be done with the participant tenderer(s) for deficient credentials noted during scrutiny of tender/offer nor any credential will be accepted after opening of the tender and the offer shall be decided on the basis of submitted/Credentials downloaded with offer only"
The tenderer whether sole proprietor/ a company or a partnership firm/ registered society / registered trust / HUF / LLP etc if they want to act through agent or individual partner(s), should submit along with the tender, a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, specifically authorizing him/them to sign the tender, submit the tender and further to deal with the Tender/ Contract up to the stage of signing the agreement except in case where such specific person is authorized for above purposes through a provision made in the partnership deed / Memorandum of Understanding / Article of Association /Board resolution, failing which tender shallbe summarily rejected. A separate power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, shall be submitted after award of work, specifically authorizing him/them to deal with all other contractual activities subsequent to signing of agreement, if required. Note: A Power of Attorney executed and issued overseas, the document will also have to be legalized by the Indian Embassy and notarized in the jurisdiction where the power of Attorney is being issued. However, the power of Attorney provided by Bidders from countries that have signed the Hague Legislation Convention 1961 are not required to be legalized by the Indian Embassy if it carries a conforming Appostille certificate
If it is NOT mentioned in the submitted tender that tender is being submitted on behalf of a Sole Proprietorship firm / Partnership firm / Joint Venture / Registered Company etc., then the tender shall be treated as having been submitted by the individual who has signed the tender.
After opening of the tender, any document pertaining to the constitution of Sole Proprietorship Firm / Partnership Firm / Registered Company/ Registered Trust / Registered Society/HUF etc. shall be neither asked nor considered, if submitted.Further, no suo moto cognizance of any document available in public domain (i.e., on internet etc.) or in Railway's record/office files etc. will be taken for consideration of the tender, if no such mention is available in tender offer submitted
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tender form (First Sheet) as per 'Annexure-I'
Firm details as per 'Annexure-II'
Self attested copy of Permanent Account Number (PAN) issued by Income Tax Department.
Documents to be submitted by tenderer as per status of their firms. These documents are listed below-
For Sole Proprietorship firm:- (i) Affidavit as per 'Annexure -X'. (ii)Special power of Attorney as per proforma given in 'Annexure-XI' to be submitted by sole proprietor firm duly notarized.(Not required if tender documents are submitted by proprietor himself) (iii) An undertaking that he is not blacklisted or debarred by Railways or any other Ministry/Department of Govt. of India from Participation in tender on the date of opening of bids, either in individual capacity or as a member of the partnership firm or JV in which he was/is a partner/member concealment/wrong information in regard to above shall make the contract liable for determination under Clause 62 of the General Condition s of Contract. (iv) All documents in terms of explanatory notes in clause 22 of STD/June/22.
For Partnership firm- (i)A notarized copy of partnership deed. (ii)A notarized or registered copy of special Power of Attorney (duly registered as per prevailing law) in favour of the individual to tender for the work, sign the agreement etc. and create liability against the firm as per proforma given in Annxure-XII (Not required if one or more partners are authorized in Parternership deed to sign on behalf of the firm.) (iii)An undertaking by all partners of the partnership firm that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India / any State Govt. from participation in tenders / contracts as on the date of opening of bids, either in their individual capacity or in any firm in which they were / are partners. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the General Conditions of Contract. (iv)The tenderer shall submit documents as mentioned in clause 23.10 of the Tender Form (Second Sheet) of STD/June/22
HUF:- (i)A copy of notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF. (ii) An undertaking that the HUF is not blacklisted or debarred by Railways or any other Ministry / Department of Govt. of India from participation in tender on the date of opening of bids, either in individual capacity or as a member of the partnership firm or JV in which HUF was / is a partner/member. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the General Conditions of Contract. (iii) All other documents in terms of explanatory notes in clause 22 of STD/June/22.
Company registered under Companies Act-2013: The tenderer shall submit :- (i) the copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company (ii) A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company, as per proforma given in Annexure-XIII' (iii) A copy of Certificate of incorporation (iv) An under taking the Company is not blacklisted or debarred by Railway or any other Ministry/Department of Govt. of India from participation in tender on the date of opening of bids, either in individual capacity or as a member of the partnership firm or JV in which the Company was / is a partner/member. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the General Conditions of Contract. (v) All other documents in terms of explanatory notes in clause 22 of STD/June/22.
LLP (Limited Liability Partnership) Firm: If the tender is submitted on behalf of a LLP registered under LLP Act-2008, the tenderer shall submit alongwith the tender- (i) a copy of LLP Agreement, (ii) a copy of Certificate of Incorporation; and (iii) a copy of Power of Attorney/Authorisation issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP. (iv) An undertaking by all partners of the LLP that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP or JV in which they were / are partners/members. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the Standard General Conditions of Contract.(v) All other documents in terms of explanatory notes in clause 22 of STD/June/22.
Registered Society & Registered Trust: The tenderer shall submit:- (i) a copy of the Certificate of Registration, (ii) A copy of Memorandum of Association of Society/Trust Deed (iii) A copy of Power of Attorney in favour of the individual to sign the tender documents and create liability against the Society/Trust. (iv) A copy of Rules & Regulations of the Society. (v) All other documents in terms of explanatory notes in clause 22 of STD/June/22.
The tenderers shall submit a copy of certificate stating that all their statements/documents submitted a longwith bid are true and factual. Standard format of certificate to be submitted by the bidder is enclosed as Annexure-III. In addition to Annexure- III, in case of other than Company/Proprietary firm, Annexure-III (A) shall also be submitted by the each member of a Partnership Firm/ Joint Venture (JV)/Hindu Undivided Family (HUF)/ Limited Liability Partnership (LLP) etc. as the case may be. Non submission of above Certificate(s) by the bidder shall result in summarily rejection of his/their bid. It shall be mandatorily incumbent upon the tenderer to identify, state and submit the supporting documents duly self attested/digitally signed by which they/he is qualifying the Qualifying Criteria mentioned in the Tender Document.
BID Security (Bank Guarantee Bond from)-Annexure-XXII, The original Bank Guarantee should be delivered in person to the official nominated as indicated in the tender document before closing date for submission of bids (i.e excluding the last date of submission of bids).
Civil engineering work in connection with " Provision of Lifts at SUDHANI, TELTA, BARSOI, KANKI, ALUABARI ROAD, DALKHOLA, KISHANGANJ & ADINA stations in connection with development of FOBs along with other ancillary works.
02-KIR-Engg-37-2026~NFR
02-KIR-Engg-37-2026
Open
Works - General
6 Months
Katihar, Bihar
₹0
₹3.7 L
7 Aug 2026
7 Aug 2026
21 Aug 2026
30 items across 1 schedule · ₹1,58,30,044.48 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | All kinds of soil | cum | 258 | 177.5 | 45,795 |
| 2 | Depth exceeding 1.5 m but not exceeding 3 m | Sqm | 257.6 | 144.1 | 37,120.16 |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. | cum | 129.2 | 196 | 25,323.2 |
| 4 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. | cum | 12.88 | 2,123.75 | 27,353.9 |
| 5 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 11.2 | 7,878.5 | 88,239.2 |
| 6 | 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) | cum | 9.36 | 6,812 | 63,760.32 |
| 7 | Foundations, footings, bases of columns, etc. for mass concrete | Sqm | 42 | 392.15 | 16,470.3 |
| 8 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. | Sqm | 1963.2 | 842.5 | 16,53,996 |
| 9 | Suspended floors, roofs, landings, balconies and access platform | Sqm | 160 | 927.25 | 1,48,360 |
| 10 | Lintels, beams, plinth beams, girders, bressummers and cantilevers | Sqm | 47.2 | 736.4 | 34,758.08 |
| 11 | Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) | Sqm | 2272 | 384.3 | 8,73,129.6 |
| 12 | Thermo-Mechanically Treated bars of grade Fe- 500D or more. | Kg | 21840 | 107.85 | 23,55,444 |
| 13 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 54 | 9,504.75 | 5,13,256.5 |
| 14 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 197.2 | 9,860.4 | 19,44,470.88 |
| 15 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 6.4 | 9,105.95 | 58,278.08 |
| 16 | Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels etc. including:(a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design.(b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metallic colour of approved shades made out of 4 mm thick aluminium composite panel material consisting of 3 mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5 mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF /Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminium Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. | Sqm | 960 | 5,015.05 | 48,14,448 |
| 17 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). | Kg | 240 | 772.4 | 1,85,376 |
| 18 | Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. | Sqm | 130 | 3,186.7 | 4,14,271 |
| 19 | Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent | Sqm | 64 | 4,481.3 | 2,86,803.2 |
| 20 | 110 mm diameter | Metre | 48 | 377.4 | 18,115.2 |
| 21 | 110x110x110 mm | Each | 16 | 234.15 | 3,746.4 |
| 22 | 110 mm bend | Each | 16 | 150.35 | 2,405.6 |
| 23 | 110 mm Shoe | Each | 16 | 131.85 | 2,109.6 |
| 24 | 110 mm | Each | 32 | 371.3 | 11,881.6 |
| 25 | 1:6 (1 cement: 6 fine sand) | Sqm | 2000 | 333.35 | 6,66,700 |
| 26 | With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre | Sqm | 2000 | 73.95 | 1,47,900 |
| 27 | Nominal concrete 1:3:6 or richer mix (including equivalent design mix) | cum | 19.6 | 2,434.25 | 47,711.3 |
| 28 | Demolishing dry brick pitching in floors, drains etc. including stacking of serviceable material and disposal of unserviceable material within 50 metres lead : | cum | 9.6 | 1,317.65 | 12,649.44 |
| 29 | Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. | Sqm | 129.6 | 266.45 | 34,531.92 |
| 30 | Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) | Kg | 2400 | 539.85 | 12,95,640 |
| Schedule total | ₹1,58,30,044.48 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
NoticeInvitinhTender.pdf
ATTACHMENT
AdvanceCorrectionSlipNo_11_.pdf
ATTACHMENT
TenderDocumentandAnnexures..pdf Tender Documents and Annexures
ATTACHMENT
TenderDocumentandAnnexures..pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].