Provn of certain sanctioned works at Yol Cantt under AGE B/R-I and AGE E/M of GE (KH) YOL

Amount

PART-I:- Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in any type of soil, complete all as specified and directed.

Excavation in trenches n exc 1.5 metre wide & n exc 1.5 metre in depth for foundation etc or for shafts, wells, cesspits manholes, pier holes etc n. exc 10 Sqm on plan n exc 1.5 metre in depth and getting out in any type of soil, complete all as specified and directed.

Hard core of broken stone or boulders of gauge not exc. 63mm deposited, spread and levelled in layers not exc. 15cm thick, watered and rammed to a true surface, complete all as specified and directed.

Plain cement concrete M-7.5, nominal mix, D-2, using 40mm graded mechanically crushed stone aggregate as in foundation filling and mass concrete, complete all as specified and directed.

Reinforced cement concrete, M-15 (Nominal mix), type B-1, (with 20mm graded crushed stone aggregate as) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed. Note: Reinforcement and form work shall be measured and paid separately.

Reinforced cement concrete, M-15 (Nominal mix), type B-1, (with 20mm graded crushed stone aggregate as) in columns, pillars, piers, posts and struts, complete all as specified and directed.

Reinforced cement concrete, M-15 (Nominal mix), type B-1, (with 20mm graded crushed stone aggregate as) in beams, cantilevers, bressummers, lintel, over 1.50m span, complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, for roughly finished flat surfaces of concrete, complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, for roughly finished square, rectangular or polygonal surfaces of concrete, complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. For roughly finished flat surfaces of concrete, complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc.25cm thick each layer of soil, complete all as specified and directed.

Removing excavated material not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified and directed.

Brick work with fly ash bricks, old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe.410 Gde-E-250 steel work, complete all as specified and directed.

Mild Steel framed work as Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete, conforming to Fe 410 Gde E-250 A, complete all as specified and directed.

Applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

Machine cut kota stone slab flooring 18-20 mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:4 (1 cement : 4 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish, laid over PCC subbase complete, all as specified.

Machine cut kota stone,18-20 mm thick , as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in vertical surfaces such as skirting/dado/riser to step/pillar aid over and including 10mm thick bedding layer in cement mortar 1:4 (1 cement : 4 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish, complete all as specified and directed.

Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering, complete all as specified and directed.

Plain cement concrete M-10, nominal mix, type C-2, using 40mm graded mechanically crushed stone aggregate as in sub base, 75mm thick, complete all as specified and directed.

Rendering cement plaster 10mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) in two layers (5mm thick first layers and 5mm thick 2nd layer) on fair faces of brick walls, complete all as specified and directed.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on other than fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, mixed with WPC, all as specified. Note : Supply only Water proofing compound shall be measured and paid for seperately.

Supply only integral water proofing compound, complete all as specified and directed.

Applying two coats of cement base paint over a coat of chalk whitening primer on newly plastered or previously undecorated wall surfaces including preparation of surface, tint and shade as approved by Engr-in-Charge.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of chalk whitening primer including preparation of surface, complete all as specified and directed.

TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

TMT bars 6 to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

1mm thick Steel rolling shutters, gear operated type with chain wheel and hand chain with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type, complete all as specified and directed.

PVC (SWR) floor trap, plain with CP grating including jointing with solvent cement, dia of outlet 75mm, all as specified.

Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonary with top ring of M-25 concrete including intercepting chamber and screen chamber made of brick masonary in CM, RCC cover slab in M-25 SFRC cover, inter connecting pipes of RCC/DWC complete filled with brick bats of size 1.8m dia 3m depth drg No CEPZ/C-TD/013/13 sheet No 1/5 to 5/5.

Plain cement concrete M-10 type C-2 nominal mix using 40mm graded aggregate as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for internal dia of pipe 150mm, complete all as specified.

Reinforced concrete pipes, class NP3, laid and jointed complete with collars, bore of pipe 150mm, all as specified.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors bore 75mm complete, complete all as specified.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall of bore 75mm including fixing adjustable clamps etc. complete, all as specified.

PVC (SWR) junction single, (Single T) equal or unequal, 75mm bore, provided with oval access door fixed, all as specified.

Plain cement concrete M-15, nominal mix, B-1 using 20mm graded mechanically crushed stone aggregate as in lintels upto 1.5 metre clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs, roof benching, haunching, water troughs and the like including watering, slightly rounded or chamfered angles and throating, complete all as directed Note :- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.

Providing precast reinforced cement concrete M-15, type B-1 (using 20mm graded mechanically crushed stone aggregate) but in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set in cement mortar (1:4) (1 cement : 4 coarse sand), all as specified. Note :- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.

Plain cement concrete M-10 nominal mix, type C-2 using 40mm graded mechanically crushed stone aggregate as in surface channel and drains, complete all as specified and directed.

Cutting openings, through brick/stone walls built in built in cement mortar for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks/stone, removing surplus serviceable bricks/stone, hardcore, etc.. to store and rubbish not exc. 50m, complete all as specified and directed.

Brick work with old size fly ash bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified and directed.

RCC M-20, nominal mix, A-1 using 20mm graded mechanically crushed stone aggregate as, in lintels up to 1.5 metre clear span cuts, steps seismic and other similar bends, coping, bands plates for serving hold fasts etc. and the like including weathering slighting rounded or chamfered angles and throating, complete all as specified and directed. Note:- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement shall be measured and paid separately.

Earth filling under floors or in foundations including watering and consolidation, complete all as specified and directed.

Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc. conforming to grade Fe.410-W.Gde-E-250 quality A, steel work, all as specified.

S & F for false ceiling of 600mmx 600mmx 4mm thick Non asbestos fibre cement building boards (designed prepainted) fixed or laid/ inserted to timber/GI/Aluminium framework with screws (E-boards) manufactured from homogeneous mixture of cement, quartz and cellulose and cured with high pressure steam using auto claving process conforming IS-14862, of size 605mmx 605mmx 4mm thick fixed over and including anodised powder coated (minimum thickness of powder coating 50 micron) snap grid frame work of T section (main and cross members) of size 25mmx 25mmx 1.5mm thick in square pattern of grid size 600mmx600mm. The aluminium frame work will supported on side wall with the used of aluminium L section of size 25mm x25mmx 1.5mm thick angles etc. snap grid shall be supported with hangers of 4mm dia galvanised iron wire adjusting level fixed to roof roof slabs/trusses etc. by means of ceiling cleats made out of galvanised iron flat of size 40x3mm of size 60mm long and expansion hold fasteners 12.5mm dia 40mm long, complete all as specified and directed. Make:- Everest or equivalent as approved by GE.

Plain cement concrete M-10, nominal mix, type C-2, using 40mm graded mechanically crushed stone aggregate, 75mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.06 Sqm but not exc. 0.11 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Glazed coloured tiles of size 350x250x/450x350x7 to 8mm thick as in vertical surfaces such as jointed in neat cement slurry and pointed with white or coloured cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Chequered cement concrete tiles machine pressed of size 20cmx20cmx 25mm thick with grey cement and no pigment, set jointed & pointed in neat cement slurry in floors laid over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Rendering cement plaster 15mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on other than fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement,complete all as specified.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, mixed with WPC @3%, all as specified. Note : Supply only Water proofing compound shall be measured and paid for seperately.

75mm thick Plain cement concrete M-7.5 nominal mix, D-2, using 40mm graded mechanically crushed stone aggregate as in sub base/flooring, complete all as specified and directed.

Three coats of white wash on newly plastered or un plastered, previously undecorated wall surfaces including preparation of surfaces, complete all as specified and directed.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 180 of MES SSR 2020 Part-II.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5 mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1) specified and directed.

S & F aluminium (powder coated with approved colour) ventilator, partially glazed and partially louvers, outer frame & mullion fabricated with aluminium section of size 82.50mmx 38.00mmx 1.50mm thick (Cat No 20036), half portion glazed with 4mm thick frosted glass including rubber beading, & glazing clip, half portion louvers of 80mm wide & 4mm thick frosted glass including aluminium louver patti incluidng S.S wire gauge of fixing of 0.36mm dia and 1.40 width of aperture with 25x3mm think aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in position complete. Note:-(i) Section No given above are of Make-Jindal, contractor may use similar section of other make mention in Appx 'C'

Butt hinges (ISI marked), medium weight, cold rolled, mild steel 100mm long, all as specified.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 300mm with lipping frame to match, complete all as specified.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 150mm, fixed, all as specified and directed.

Extruded aluminium alloy handles (ISI marked), cast type, anodised, of size 150mm, fixed, all as specified and directed.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position inbcluding brass ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with water supply line, complete all as specified and directed.

Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with PVC ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-1 using 20 mm graded crushed stone aggregate complete all as specified, including making connections to trap and to flush pipe etc, and making good to floors to match existing, fixed complete, all as specified. Make:- Cera Cat part No 2071 or equivalent makes in Appx 'C'.

Vitreous China wash down water closet (pedestal pattern), coloured including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC coloured seat cover black closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device and chromium plated jet including 15mm dia PVC connection 600mm with CP brass coupling nuts and PVC washers at both ends, fixed complete, including 32mm dia PVC long bend flush pipe 90cm long pipe and fixed, complete all as specified.

Supply and fixed PVC valveless, crystal white, syphonic action type flushing cistern 10 litres capacity, plunger type low level with inlet, ball valve, float and handle with brackets including 32mm dia PVC long bend flush pipe 90cm long and 15mm dia PVC connection 600mm with CP brass coupling nuts and PVC washers at both ends, fixed complete, all as specified. Make:- Cera Cat part No 2602 or equivalent makes in Appx 'C'.

Wash basins, Vitreous China (Flat back type) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with CP coupling nuts at both ends, waste pipe of polythylene of low or high density or PVC of 32mm dia and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed, complete all as specified. Make:- Cera Cat part No 1008 or equivalent makes in Appx 'C'.

Chromium plated brass shower rose, fancy type, 125mm size with shower arm, chromium plated, 195mm longh with bend of 45 degree with flange suitable for 15mm bore pipe with swivel joint fixed to pipe, complete all as specified.

Salt-glazed stoneware gully traps, round mouthed, type 'P' of size 150x150mm, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors bore 110mm complete, complete all as specified and directed.

PVC (SWR) junction single, (Single T) equal or unequal, 110mm bore, provided with oval access door fixed, complete all as specified.

PVC (SWR) bends any radius, 75mm bore with ovel access door, complete all as specified.

PVC (SWR) bends any radius, 110mm bore with ovel access door, complete all as specified.

PVC (SWR) 110mm vent cowl, complete all as specified and directed.

Mild steel galvanized iron water tubing 15mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor, complete all as specified and directed.

Mild steel galvanized iron water tubing 20mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor, complete all as specified and directed.

Mild steel galvanized iron water tubing 25mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor, complete all as specified and directed.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed of 15mm bore and fixed, complete all as specified and directed.

Bib taps, 15mm bore, cast copper alloy with crutch or butterfly handle, fancy type chromium plated screwed for iron pipe or for brass ferrule and fixed, complete all as specified.

Angle valve, cast copper alloy, fancy chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed, complete all as specified and directed.

Stop valve, cast copper alloy, fancy, type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed, complete all as specified and directed.

20mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule fixed, complete all as specified and directed.

Soap dish, vitreous China white, approximate size 160x160x90mm, chromium plated, fixed to plugs with chromium plated, brass screws, complete all as specified.

Brass Chromium Plated, Tubular towel rail, 20mm dia, D type, 60cm long between flanges, with brackets, fixed with chromium plated brass screws, fixed, complete all as specified and directed.

PVC connection 15mm size with PTMT nuts at boths end 450mm long and fixed, complete all as specified and directed.

Plain cement concrete M-15 nominal mix, type B-2 using 20mm graded mechanically crushed stone aggregate as in surface channel and drains, complete all as specified.

Walling random rubble masonry with best quality locally available stone, uncoursed, well bonded, bedded, solidly hearted and built in cement mortar 1:6 (1 cement : 6 coarse sand), all as specified.

Septic tank, excavation in any type of soil, foundation in PCC 1:2:4, brick work in CM 1:4, RCC slab covers including RCC precast manhole cover having 6mm plate embedded all around/fibre reinforcement cover with angle iron frame vent shaft and sludge chambers 100mm CI pipe, and cowl chamber, etc complete for 50 users, (Drg No. CEPZ/C-TD/13/13 sheet 1/1 to 1/5) complete all as specified and directed. Note:- (i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day.

Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonary with top ring of M-25 concrete including intercepting chamber and screen chamber made of brick masonary in CM, RCC cover slab in M-25 SFRC cover, inter connecting pipes of RCC/DWC complete filled with brick bats of size 1.8m dia 4.5m depth drg No CEPZ/C-TD/013/13 sheet No 1/5 to 5/5.

Forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work with cement mortar 1:6, complete all as specified and directed.

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.11 Sqm but not exc. 0.18 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Plain cement concrete M-15, nominal mix, type B-0, using 12.5mm graded mechanically crushed stone aggregate as in floors, 25mm thick, surface finished even and fair, complete all as specified.

Butt hinges (ISI marked), medium weight, cold rolled, mild steel 75mm long, complete all as specified.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 100mm, fixed, complete all as specified and directed.

Extruded aluminium alloy handles (ISI marked), fabricated type, anodised, of size 100mm, fixed, complete all as specified and directed.

Factory made fully glazed (frosted/ground/obsecured) solid panel PVC ventilator or window shutter 30mm thick (style) consiisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC C channel heaving a PVC sheet strip of 20mm width such inside with solvent ement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail either side & as gap insert for top rail & bottom rail as per specification & drawing. (Rate incl glass/gauges)

Mild steel galvanized iron water tubing 32mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor, complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick walls, complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exc 10 cm but n.exc 20cm girth in brick walls, complete all as specified and directed.

Supply only Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

Flush pipe of polyethylene of low or high density or PVC 32mm dia, for low level cistern, including Joint between fluslhing pipe, complete all as specified and directed.

Vitreous China Urinal, Half stall type, white including PVC waste pipe, including providing and fixing plugs, beding urinal against wall in cement mortar 1:2 securing urinal plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe including fixing supply pipe to flushing cistern trap and including 32mm bore PVC waste pipe and fixed, complete all as specified.

15mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule fixed, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall of bore 110mm including fixing adjustable clamps etc. complete, all as specified.

PVC (SWR) Branch piece, (Single Y) equal or unequal, 75mm bore, provided with oval access door all as specified.

PVC (SWR) reducer 110mm bore complete, all as specified.

PVC connection 15mm size with PTMT nuts at boths end 600mm long and fixed, complete all as specified and directed.

Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) and fixed, all as specified.

Urinal spreader of PTMT any colour for fixing with 15mm dia pipe. (Minimum weight 60gms), fixed complete all as specified.

Waste coupling of PTMT (half or full threaded). (Minimum weight 32mm-45gms/40mm-60gms), complete all as specified.

Reinforced concrete pipes, class NP2, laid and jointed complete with collars, bore of pipe 150mm, complete all as specified and directed.

Cutting existing steel tubing of 15mm bore for alterations or additions (Each cut measured) if necessarily done in position without taking down complete, all as specified and directed.

Cutting existing steel tubing of 20mm bore for alterations or additions (Each cut measured) if necessarily done in position without taking down complete, all as specified and directed.

S&F for ‘P’ or ‘S’ trap of 110mm dia.

Cutting into existing manholes for connecting new drains, any dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round 3/4 channel) in cement concrete M-15 type B-1 smooth, finished and reforming benching as required dia of pipe 110mm, complete all as specified and as directed.

Bottle trap 32mm bore of PTMT having minimum water seal of 25mm. (Minimum weight 32mm-260gms/ 40mm-270 gms)

Vitreous china urinal partition white of size 310x700 mm fixed with stainless steel screw to wall, complete all as specified and as directed by Engr-In-Charge.

20mm bore Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions cutting, threading existing GI pipe and fixed, complete, all as specified.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped end etc. all as specified.

Machine pressed precast concrete interlocking paver block factory manufactured (ISI Marked), any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigment, complete all as specified and directed.

Plain cement concrete M-15, nominal mix, type B-2, using 40mm graded mechanically crushed stone aggregate as in sub base floor, 75mm thick, complete all as specified and directed.

Sand filling under floors or in foundations including watering and consolidations, complete all as specified and directed.

4mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 Sqm in each pane, complete all as specified and directed.

Rough excavation not exceeding 1.5 m deep and getting out, complete all as specified and directed.

Supply only approved earth obtained from outside MD land and depositing at site, complete all as specified and directed.

Forming embankments including raising (or lowering) earth, spreading in layers n exc. 30cm thick; watering, ramming/rolling and finishing to required size, shape, etc., n exc. 1.5m high from base (solids), complete all as specified.

Granite (jet black) 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement(1:2) with admixture of pigment to match the shade of granite stone including grinding and polishing complete as in kitchen platform, window cill /steps laid over and including 15mm thick screed bed in cement mortar (1:6), all as specified.

Manufacturing, supplying and fixing retro reflective Cautionary /warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm and made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours). Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing, specification and direction of Engineer-in-charge.

Supply, installation and commissioning of EFFLUENT TREATMENT PLANT(ETP) of capacity 1 KLD, incorporating the following items: (i). M&L for Chemical Reaction tank with Flocculation Chamber M.S tank with FRP Lining of Thickness 4.0 mm - 1 Nos. (ii). S&F Effluent Transfer Pump of Size = 1” x 1” Motor = 1.0 H.P, R.P.M = 2880 complete all as specified & directed by Engr-in-Charge - 1 Nos. Make:- Crompton (SS). (iii). S&F Roots Blower (Compressor) Capacity=30 c.f.m Motor 1.0H.P, R.P.M=1440 Blower complete all as specified & directed by Engr-in-Charge-1 set. Make:- NGI/ Aakash/Eqv. Motor= Kirloskar. (iv). S&F Plumbing, with accessories PVC/G.I pipe fitting for pump, chemical reaction tank, tube settler, valves Tube Settler etc - 1 Lot. (v). Erection, fitting and platform for dosing tank with materials.Channels 4”x2”, Angle 2”x2”, Angle 1½”x1½”, Square Hollow pipe 1”x1” complete all as specified & directed by Engr-in-Charge - 1 lot. (vi). S&F Tube Settler Capacity = 0.75 x0.75 x 2.5 m PPFRP Thickness of sheet 4.0 mm Media = Tube PVC - 1 Nos. (vii). S&F Chemical Dosing tank (PVC Tank) 100 litre (2 Nos). (viii). S&F Activated Carbon Filter ,Media filter. Size = 13” dia x54” height. M.O.C = FRP - 2 Nos. (ix). S&F Pump for Activated Carbon Filter Size = 1” x 1” Motor = 1.0 H.P, R.P.M = 1440 - 1 No Make:- Kirloskar / Crompton. (x). S&F Lime dosing tank of suitable capacity as required on site - 1 No. (xi). S&F Automatic dosing pump for Polly&Alum dosing of suitable cap as required on site-2 Nos. (xii). S&F of Control Panel with all acessories required for ETP Plant complete all as specified & directed by Engr-in-Charge - 1 No. (xiii). Electrical Supply to mains of equipment with 3 phase cable/wire as required on site with Electrical fittings, wiring push-button switches & MCB etc. for the Effluent Treatment Plant - 1 lot. (xiv). Provision of influent to the ETP & discharge of treated water from the outlet of the 2 HP PP Centrifugal Pump with valves,fitting and pipe - 1 lot. (xv). S&F of Chemicals, lubricants & other usable required at the time of trial run - 1 lot.

Point wiring with 1.5 Sqmm copper conductor FRLS (Multi strand) PVC insulated ISI Marked unsheathed cable in and including concealed PVC conduit medium grade, ISI marked of suitable size with all fittings/ accessories and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FLRS as phase, neutral and earth wire connected to common earth dolly and including concealed pressed steel/ cast iron of suitable sizes (modular sunken box) terminal boxes made from 1.60 mm thick sheet for mounting of switches, sockets, fan regulators, light fittings etc. and modular cover plate as top cover for one light point or one fan/exhaust fan point or one bell point, independent, controlled by one way switch/ push button complete all as specified and directed. Note:-i) Wiring colour code i.e Red/Yellow/Blue for phase, Black for neutral and Green for earth shall be maintained. (ii) Rate of cutting chases, cement plaster, white wash and making surface good as existing surface included in quoted rate. (iii) Point wiring is considered for Modular Switches and sockets. Rate of Metallic Sunken box and modular sheet cover plate and other connected accessories required for modular point wiring included in quoted rate. (iv) Rate of modular switch and sockets will be paid seperately under relevant item.

All as per serial item No '132' above, but for one 3 pin 5 Amps socket outlet on the same board, complete all as specified and directed.

All as per serial item No '132' above, but for one 3 pin 5 Amps socket outlet on the independent board, complete all as specified and directed.

All as per serial item No '132' above, but for 3 pin 15 amps socket out let on independent with 2.5 Sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, complete all as specified and directed.

Supply and fix modular switch piano flush type one way 6 Amps, 1 module, 230V, Fixed complete all as specified.

Supply and fix modular switch piano flush type one way 16 Amps, 1 module, 230V, Fixed complete all as specified.

S&F Modular socket 6 Amp 3 Pin, two module 230 Volts, Fixed complete all as specified.

S&F Modular socket 6/16 Amp 5 Pin, two module 230 Volts, Fixed complete all as specified.

Supply and fix modular cover plate with frame, 3 module all as specified and as directed by Engr-in- Charge.

Supply and fix modular cover plate with frame, 8 module all as specified and as directed by Engr-in- Charge.

Supply and fix modular metal flush box 3 module Fixed, complete all as specified.

Supply and fix modular metal flush box 8 module Fixed, complete all as specified.

Ceiling rose, three phase, 3 terminals 65x20mm, PVC/Polycarbonate, insulated body, fixed all as specified.

Single pole and neutral enclosure with a two pin and earth plug top and socket complete with one double pole MCB 20 Amps, complete all as specified.

Sheet metal enclosures factory made for DBs when MCBs to be used, single pole and neutral (double Door), 8 way, 240 volts with 200 Amp rated bus bar, complete all as specified.

MCB SP 6 to 32 Amp, 240 Volts, 10 KA, C series, complete all as specified. Note:- The connection to the MCBs shall be done through thimble/lugs do not direct wire shall be connected to MCBs.

MCB SPN 32 Amp, 240 Volts, 10 KA C series, complete all as specified. Note:- The connection to the MCBs shall be done through thimble/lugs do not direct wire shall be connected to MCBs.

M & L for sub main wiring with two single core PVC insulated unsheathed, 1100 Volts grade, (FRLS) copper cable 6 sqmm stranded conductor and drawing through and including rigid PVC non metalic surface conduit medium duty (ISI Marked) with conduit accessories such as junction boxes, bends, tees etc. including continuous earth wire PVC insulated unsheathed 1100 volts grade, cable 6 sqmm copper conductor and connected to common earth dolly complete as directed. Note :-(i) One run of PVC conduit, two runs of cable (Phase + Neutral) and one run of earth wire shall be measured and paid as one unit.

LED Decorative ultra slim square profile LED lighting integral type fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack, 20 watt LED, 230V, and making connection with 2 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete, all as specified and directed.

35W new generation energy saving and environmental friendly long life LED Bldg security light made up of pressure die case aluminium housing with high power LED as lighting source an lens enbedded PC cover having TOP opening seperate toughted glass/verminproof driver compartment, SPDs with IP66 protenction and impact resistancee of IK07 connecting with PVC insulated three core flexible copper conductor of suitable size from ceiling rose to fitting including bracket of suitable size, complete all as specified and directed.

Supply and installing of the electric water storage heater of ABS body type of 25 litre capacity with rated power 2 KW, 5 star rated, vertical type, thermally insulated Mild steel tank with glass line coating inside the tank alongwith glass lined incoloy heating element with anti corrosive magnesium anode, NRV, thermostate, indicators and temperature adjustable knob including steel braided flexible connection for pipe of size 15mm dia bore GI hexagonal adopters/Nuts on both side of inlet (cold water supply) and outlet (hot water supply) and including provision of wall mounting arrangement and mounting on wall with suitable size of anchor bolts with complete connection of water including testing after installation, complete all as specified and as directed by Engr-In-Charge.

Supply and fixing of Exhaust fan (domestic purpose) of sweep 300mm, single phase, with louver shutter and connecting with electrical system, including provision of cable copper flexible, PVC three core 23/0.0076 from ceiling rose to fan and grouting of holding down bolts in and including PCC M-15 (nominal mix) blocks, fixed on wall with angle iron frame of size 35 mm x 35 mm x 3 mm complete all as specified and directed by Engr - in - Charge. Note : (i) The contractor shall make necessary opening in existing walls & prepare the surface in shape & making necessary fixing arrangement of exhaust fan & grouting of suitable holding nuts & bolts in PCC 1:2:4 type B1 & make good the surface after completing the work. (ii) Unit rate quoted deemed to be included this aspect.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of plate not less than 1.5m below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15 mm bore including provn of concrete pit in plain cement concrete M-20 type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of rainforced cement concrete M-20 reinforced with XPM (weight not less than 4 kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75m long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion. NOTE:- Item of earthing includes the cost of 7.5m long galvanised iron earth wire 4mm size and protection pipe of 15mm bore galvanised iron light grade and earth work.

Supply and fix LED focus light 60W cool white IP 66 protection done through direct wire shall be connected to MCB's. Make:- Havells or equivalent Philips, wipro

Supply and fix LED strip blue colour IP 66 protection done through direct wire shall be connected to MCB's. Make:- Havells or equivalent Philips, wipro

Supply, fixing and testing submersible motor three phase 5HP alongwith all electric connections and water pipeline connections inlet dia 40mm and outlet dia 40mm, complete all as specified and directed by Engr-In-Charge.

Supply and fix star delta starter three phase for pump motor 5HP capacity at user site and complete testing, complete all as specified and directed by Engr-In-Charge. Make:- L&T/Havells/Standard

Supply and fix modular cover plate with frame, 1 module all as specified and as directed by Engr-in- Charge.

Supply and fix modular metal flush box 1 module Fixed, complete all as specified.

M & L for sub main wiring with two single core PVC insulated unsheathed, 1100 Volts grade, (FRLS) copper cable 4 sqmm stranded conductor and drawing through and including rigid PVC non metalic surface conduit medium duty (ISI Marked) with conduit accessories such as junction boxes, bends, tees etc. including continuous earth wire PVC insulated unsheathed 1100 volts grade, cable 4 sqmm copper conductor and connected to common earth dolly complete as directed. Note :-(i) One run of PVC conduit, two runs of cable (Phase + Neutral) and one run of earth wire shall be measured and paid as one unit.

Supply, fixing and testing complete of PIR flush mount dual load 360 degree standalone seser, complete all as specified and directed by Engr-In-Charge. Make:- Schneider cart part No. SAE-UE-MS-CDBWE.

Eshaan Construction Co.