Project Nos. 146- 2025-26 - SITC of 8 Mtr Low Mast with 4 nos of 100W LED Flood Light at 7 Various locations in Koduvally Municipality under Annual Plan 2025-26.

Amount

Civil Work

2.6.1 – Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

4.1.8 – Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

5.9.1 – Centering and shuttering including strutting, etc. and removal of form for: Foundations, footings, bases of columns, etc for mass concrete

5.22.6 – Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo - Mechanically Treated bars of grade Fe-500D or more

5.1.2 – Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level: 1:1.5:3 (1 cement 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

13.1.1 – 12 mm cement plaster of mix: 1:4 (1 cement : 4 fine sand)

2.25 – Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m

Electrical Work

90.15.1.1 – Supply installation testing and commissioning of Octagonal Pole made of hot dip galvanised GI sheet 70mm top diameter, 130mm bottom diameter, thickness 3mm, base plate dimensions of 200x200x16mm suitable for windspeed as per IS 875 Part III, fixed head frame including round arm luminary carriage suitable to install 4/6 nos luminaries in symmetrical arrangement including connector, foundation bolt 4 nos, existing RCC foundation and junction box etc, complete 8 Meters

90.15.4.7 – Supply Conveyance, installation, testing and commissioning of 100W LED Flood light, output greater than 105 lumen/W, 4000-6000 K with IP 66 protection, LED Chip make Cree/Lumilled/Nichea with power factor greater than 0.95 at full load, internal surge protection up to 8 KV, Aluminium pressure die-cast powder coated housing, acrylic cover complete with THD less than 10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be separately accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer)

OD152891/2025-2026 – Supply Fabrication and Installation of Sintex box

90.14.3.2 – Supply and providing heavy duty 'A' section neoprene gasket in the panel board ‘U’ section rubber beeding suitable for 1.60/2.00 mm sheet

90.14.5 – Supply and fabrication conveyance and installation of angle iron frame work for wall mounting panel board

OD152882/2025-2026 – Supply and fixing of 1 no. of 25 A 4 Pole AC 1 rated power contractor, 25 A connector, 1 no. of Digital timer, suitable copper socket, 2.5 Sq.mm ISI marked FRLS PVC insulated single core copper conductor cable, 1.5 sq.mm ISI marked FRLS PVC insulated single core copper conductor cable

OD149724/2025-2026 – Supply and fixing HRC fuse base of 20/32A using suitable nut and bolt, 32A 2-way neutral links mounted on DMC/SMC base and 2.5 sq.mm ISI marked FRLS PVC insulated single core copper conductor cable

2.14.2 – Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

2.10.3 – Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole

2.10.1 – Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

2.12.1 – Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

90.6.5.11 – Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes. 3 core 1.50 sq mm

5.1 – Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt ) as required

90.16.4.2 – Supply and clamping the following sizes of strips on surface of wall / parapet/ existing cable tray using clamps fabricated from 20 x 3 mm GI flat duly painted or heavy duty GI spacer saddles, spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required (for vertical run). 25 x 3 mm GI strip

90.16.1.3 – Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required. 3.15 mm copper conductor (10 SWG)

90.16.5.3 – Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required. 3.15 mm (10 SWG)

90.12.5.3 – Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required. 2 core 10 sq mm

90.12.9.2 – Supplying, laying and jointing of the following sizes of double wall corrugated (DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanical protection to underground power cables with all required accessories in ground in the existing trench. 50/38 mm or nearest size

9.1.2 – Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2 X 10 sq. mm (19mm)

OD149725/2025-2026 – Supply and fixing of Name Board with Angles, Flats, Square pipe, ACP Sheet including Nut & Bolt

Connection charges - KSEB

KOCHUMELATHIL AGENCIES (BID ID -2350097)

Sinelab Technologies Pvt. Ltd (BID ID -2348681)