GE/CHD-93/2024-25 SPECIAL REPAIRS TO MAIN OFFICE AND COOK HOUSE BLDG NO P-53 TYPE D AT N AREA UNDER GE CHANDIGARH

Amount

Taking down Cement plaster or cement lime plaster on brick or stone walls including raking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) as in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Demolition of Cement concrete unreinforced as in Ground Floor and paving n. exc. 15cm thick (above or below G.L.) complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames n.exc 1.5 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames exc 1.5 sqm but n.exc 4 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts etc complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 sqm each but not exc 2 sqm each and refixing in the same opening complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 sqm each but not exc 2 sqm each and removing from the site complete all as specified and directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for and removing from the site complete all as specified and directed by Engineer-in-Charge.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc, removing rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Demolition and taking down eaves gutter and AC/PVC/CI rain water pipe any size or pattern incl all fittings, heads, shoes, bends,Swan necks, etc including cleaning or refixing or removing to store (measured overall as fixed along centre line over fittings and accessories) complete ,all as specified and as directed by Engineer-in-Charge.

Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Cutting channels, grooves or rebates 75 mm wide and 65 mm deep and making good in cement mortar 1:3 after inserting APP membrane complete all as specified and directed by Engineer-in-Charge.

Disconnecting existing tanks of capacity exc. 500 ltr & n. exc. 1000 ltr, setting aside and removing from site complete all as specified and directed by Engineer-in-Charge.

Taking down steel rolling shutters size exc 2.0 sqm each but n.exc 15 sqm each and removing from the site complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work or stone/boulder masonary built in cement mortar incl all quions arches, pillar or any other descrption etc complete all as specified and directed by Engineer-in-Charge.

Dismantling existing brick tiles or terracing tiles, single layer on roofs from any position grouted in cement mortar including removal of any existing treatment complete all as specified and directed by Engineer in Charge.

Dismantlling Mud phuska in roofs, any thickness,including plastering and leeping (whether full thickness removed or only a part thereof) in any position including disposal of unservicable rubbish outside Cantt area complete all as specified and directed by Engineer in Charge.

Demolition of entire Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings etc complete all as specified and directed.

Dismantling wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete, all as specified and as directed by Engr-in-charge.

Supplying & fixing of PVC water storage tank 1000 ltr capacity HDPE triple layered ,white colour cylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection incl locking arrangement, including tank nipple 15/20 mm ,supplying & fixing of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 200 mm - 210 gms ) complete Note : (i) Inlet, outlet & wash out pipe will be measured paid for separately. (ii) The quoted rate is inclusive of minimum one union each on inlet and outlet of water tank as per size of pipe shall be provided.

Supplying & fixing of PVC water storage tank 500 ltr capacity HDPE triple layered ,white colour cylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection incl locking arrangement, including tank nipple 15/20 mm ,supplying & fixing of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 200 mm - 210 gms ) complete Note : (i) Inlet, outlet & wash out pipe will be measured paid for separately. (ii) The quoted rate is inclusive of minimum one union each on inlet and outlet of water tank as per size of pipe shall be provided.

25 mm thick Cement concrete (1:2:4) type B-0,using 12.5 mm graded mechanically crushed stone aggregate as in floor and pavings etc. or any other situation complete all as specified and directed by Engineer-in-Charge.

75 mm thick, cement concrete type C-1, 1:3:6 using 20 mm graded stone aggregate, finished even & smooth without using extra cement, as in plinth protection, complete all as specified.Plinth protection shall be laid in 1:20 slope and joint filling sealed with bituminous sealing compound grade "A" .

Plain cement concrete (1:4:8) type D-2,using 75 mm graded stone aggregate as in foundations, filling and mass concrete, sub base etc complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in cement concrete in roof kerbs padding or mud stops,back filling of chowkats, coping,bed plates rounded or chamfered on edges with and including using necessary use and waste of formwork for fair finished surface complete all as specified and directed by Engineer-in-Charge.

Reinforced Cement Concrete nominal mix 1:1.5:3 type A using 20mm graded mechanically crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer-in-Charge.

TMT steel bars 10mm dia and over, of grade Fe-500D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

TMT steel bars 5mm dia and over upto and including 10mm dia , of grade Fe-500D cut to length, bent to shape required, including cranking, bending stirrups spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in strirrups , spacers and binders complete all as specified and directed by Engineer-in-Charge.

First quality Non - skid coloured Ceramic tiles 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc. set and jointed in neat cement mortar over and inculding 15 mm thick screed in cement mortar (1:6) and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

First quality Non - skid coloured Ceramic tiles 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm as in floors etc. set and jointed in neat cement mortar over and inculding 15 mm thick screed in cement mortar (1:6) and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

Glazed ceramic coloured tiles 450 x 300 x 7mm thick on vertical surface such as skirting , dado etc. over and including 10 mm thick rendering in CM 1:4 thick set and jointed in neat cement mortar and pointed in white or colour cement to match tiles complete all as specified and directed by Engineer-in-Charge.

Machine cut Kota stone slab flooring 20-22 mm thick,SIZE 55 CM x 55 cm laid over & including 20 mm thick screed bed in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified and directed by Engineer-in-Charge.

Machine cut Kota stone slab 20-22 mm thick as in skirting, dado and pillars etc , laid over & including 10 mm thick rendering in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified and directed by Engineer-in-Charge.

Green Marble 18-20 mm thick, (table rubbed and polished) in single piece (in one direction) machine cut, machine polished, bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 20 mm thick (average thickness) cement mortar (1:4) screed, as in cooking platform, shelves, RCC counters, window cills & similar situations, complete all as specified and directed by Engineer-in-Charge.

Granite 18-20 mm thick, (table rubbed and polished) in single piece (in one direction) machine cut, machine polished, bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:3) screed, as in cooking platform, shelves, RCC counters, window cills & similar situations, complete all as specified and directed by Engineer-in-Charge.

Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 EXCEPT BRICKS complete all as specified and directed by Engineer-in-Charge.

60mm thick machine pressed precast concrete ( M-35 grade) prepolished rubberized moulded interlocking paver block manufactured in an automatic plant working on vibration and simultaneous hydraulic compression from top, with grey cement and pigment(Yellow & red) any shape and size confirming to IS 15658-2006 laid over and including 50 mm thick cushion of coarse sand & filling the joints after laying complete all as specified and as directed.

Endore tile good grip series 300x300x 8-10mm thick of colour set in neat cement slury , pointed with pigment over and including screed bed or bedding layer 15mm thick cm1.6 complete all as specified and directed.

Grey coloured PCC factory made tiles, ISI marked, 25 mm thick of size 250 mm x 250 mm, machine pressed and cut polished and set jointed and pointed in neat cement slurry and fabricated using grey cement & pigments. over and including 20 mm thick screed bed in cement mortar (1:4) mixed with and including WPC as per manufacturers instruction ,bedding joints grouted flush in cement mortar (1:3) complete all as specified and directed by Engineer-in-Charge.

Water proofing roof treatment using APP polymeric water proofing membrane minimum 3 mm thick and weighting not less than 3.6 Kg/Sqm black finish reinforced with non-woven polyster matt wt not less than 150 gms/Sqm with thermo fusable finish laid over compatible bitumen primer at the rate of 0.40 Ltr/Sqm over cleaned surface including parapet,applying a coat of blown bitumen 85/25 grade @ 1.2 kg per square metre over priming coat torching over laps with a propane or butan gas torch with a over lap of 100 mm at the side and 150 mm at the ends and sealing all as per manufacturers instructions incl wire brushing and cleaning the top surfaces of concrete, roof surfaces etc. with water including flashings and junction of parapets etc complete all as specified and directed.

Rendering 15 mm thick in cement mortar 1:6, on fair faces of brick or concrete surfaces , trowelled to even and smooth surface without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick in cement mortar 1:4, on brick or concrete surfaces in two layers mixed with water proofing compound on top layer, trowelled to even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. NOTE: Water proofing compound shall be measured and paid separately.

Rendering 5 mm thick in cement mortar 1:3, on concrete surfaces (such as top & sides of chajjas,beams,balcony,ceiling etc ) trowelled to even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick in cement mortar 1:3, on roof surfaces including flashings and junction of parapets,brick or concrete surfaces in two layers mixed with water proofing compound on top layer, trowelled to even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. NOTE: Water proofing compound shall be measured and paid separately.

Supply only liquid water proofing comound ISI Marked complete all as specified and directed.

Preparation of new external surfaces of walls brooming down, applying one coat of white cement based wall care putty 1 mm thick etc complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper on walls over and including a coat of primer and 1 mm wall care puty including preparation of surface complete all as specified and directed.

Preparation of new plastered surfaces and applying two coats of weather proof exterior emulsion paint(Ist quality) Apex over a coat of primer on damp surface as per manufacturers instructions etc including properly filling the cracks with putty,applied by approved applicator complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment,preparation of surfaces and applying two coats of weather proof exterior emulsion paint(Ist quality) Apex over a coat of primer on damp surface as per manufacturers instructions etc including properly filling the cracks with putty,applied by approved applicator complete all as specified and directed by Engineer-in-Charge.

Preparation of old Plastered of walls etc by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying two coats of oil bound distemper on walls complete all as specified and directed by Engineer-in-Charge.

Material & Labour 12 mm thick Particle board for insulation purposes, fixed with nails to timber framework with rubber packing,anodised aluminium snap beading,anodised aluminium fittings complete ,all as per the direction of Engineer-In- Charge.

Factory made Pressed steel frames, confirming to IS, having profile 125 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and fixing only 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.

Factory made Pressed steel frames, confirming to IS, having profile 105 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and fixing only 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.

Solid PVC door frames of size 50mm x 47 mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube, and edges will be painted to match with printed sheet, supply & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles),With Wood free EPS with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification to be fitted in the MS frame welded/scaled to the stiles & rail with suitable PVC sheet beading & jointed together with solvent cement supply & fixing in the frame at site as per specification & drawing.

35 mm thick factory made Plain, framed, panelled shutters of 2nd class Hardwood (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkat complete all as specified and directed by Engineer-in-Charge.

35 mm thick factory made glazed & Skeleton shutters of 2nd class Hardwood open rebated & prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size ofstiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2009) complete all as specified and directed by Engineer-in-Charge.

Factory made box type steel windows with pressed steel frame min 1.25 thick complete including mild steel acessories like lugs, door stopper, holdfasts, pintol hinges, handles( minimum One for each shutter), and ISI marked tower bolt 150mm size (minimum 2 for each shutter) etc. with glazing bars dovetailed or welded with one shop coat of zinc chromate primer including cutting holes, complete all as shown on drawing No. TD-276(R), Sheet No 1/4 to 2/4, 3/4, 4R/4 and as specified and directed by Engineer-in-Charge. Note: (i) Fabrication as per TD-276 (R) SH 1/4 to 2/4, 3/4, 4 (R) /4 (ii)Mode of measurement Unit will be for the complete window except Glass/ Gauge but incl fittings, ISI marked iron mongery complete as per TD. (iii) The PCC back filling in chowkhat of window, Grills,Sheet glass and wire gauge will be measured and paid separately against respective items.

Factory made box type steel windows with pressed steel frame min 1.25 thick complete including mild steel acessories like lugs, door stopper, holdfasts, pintol hinges, handles( minimum One for each shutter), and ISI marked tower bolt 150mm size (minimum 2 for each shutter) etc. without glazing bars dovetailed or welded with one shop coat of zinc chromate primer including cutting holes, complete all as shown on drawing No. TD-276(R), Sheet No 1/4 to 2/4, 3/4, 4R/4 and as specified and directed by Engineer-in-Charge. Note: (i) Fabrication as per TD-276 (R) SH 1/4 to 2/4, 3/4, 4 (R) /4 (ii)Mode of measurement Unit will be for the complete window except Glass/ Gauge but incl fittings, ISI marked iron mongery complete as per TD. (iii) The PCC back filling in chowkhat of window, Grills,Sheet glass and wire gauge will be measured and paid separately against respective items.

PVC hollow wall panelling 5mm thick any colour/design approved by engr-in-charge, inclusive of fixing on to wall incl moulding end caps fixed with PVC sleeves and screws as required at site including dismantling of walls and ceiling boards/wall paneling or insulation board any thickness, including cover fillets complete all as specified and directed

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge complete all as specified and directed by Engineer-in-Charge.

Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per drawings and the directions of Engineer-in-Charge

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement. complete as per drawings and the directions of Engineer-in-Charge

100 mm, Aluminium handles, fancy type,cast type,anodised complete all as specified and directed by Engineer-in-Charge.

300 mm long,Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified & directed by Engineer in Charge.

150 mm long extruded aluminium alloy handles, fabricated type,anodised complete all as specified and directed by Engineer-in-Charge.

Aluminium anodised,barrel tower bolts of extruded section with length of bolt 200 mm and dia of bolt not less than 10 mm,ISI marked complete all as specified and directed by Engineer-in-Charge

Anodised aluminium fittings such as Hat stands 150 mm long complete all as specified and directed by Engineer-in-Charge.

Anodised aluminium fittings such as peg stays 150 mm long complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 100 mm long medium weight with stainless steel screws complete ,all as specified and as directed by Engr-in-charge.

Supply and fixed 4 lever Mortice lock size 75 mm fixed to aluminium door and frame complete all as specified and directed by Engineer-in-Charge.

Mild Steel Framed work as in guard bars/grills, gratings, etc.. with ends of bars shouldered/welded and/or riveted, or forged into spikes; framed guard bars/grills conforming to Fe-290 (Gde E-165) complete all as as specified and directed by Engineer-in-Charge.

Mild Steel Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing completeconforming to Fe-290 (Gde E-165) complete all as as specified and directed by Engineer-in-Charge.

Mild Steel work as in Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 conforming to Fe 410-W (Gde-E- 250) quality-A and fixing complete all as as specified and directed by Engineer-in-Charge.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws,hooks etc complete all as specified and as directed by Engr-in-charge.Colour to be decided by GE

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws,hooks etc complete all as specified and as directed by Engr-in-charge.Colour to be decided by GE

Steel rolling shutters, thickness of lathe 1.25 mm,with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated,complete: push pull or manual type complete all as specified and as directed by Engr-in-charge.Colour to be decided by GE

Ball bearing for rolling shutters complete all as specified and as directed by Engr-in-charge.Colour to be decided by GE

Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and as directed by Engr-in-charge.Colour to be decided by GE

Stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

Sheet glass 4 mm thick, ordinary quality and glazing with linseed oil pane putty & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sq. mtr in each pane, complete all as specified and directed by Engineer-in-Charge.

Preparation of new or previously untreated wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Preparation of old wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

Preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

Preparation of old steel and iron surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

25mm dia stainless steel fancy type drapery rod of wall thickness 0.9 mm including taking out of old pelmet/bracket, complete all as specified and directed by Engineer-in-Charge.

Stainless steel bracket and stainless steel fancy type fennel complete all as specified and directed by Engineer-in-Charge. Note: The quoted rate includes one pair comprising of two brackets and two fancy type fennels.

Supply and fixing in repair Waste coupling of PTMT (half or full threaded) suitable for 32 mm dia discharge pipe (Minimum weight 45gms) complete ,all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type bib tap brass short body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 15 mm Gun-metal, globe or gate valves, with MS lever handle, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 20 mm Gun-metal, globe or gate valves, with MS lever handle, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type Pillar taps, cast copper alloy, with capstan heads,chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs fancy type stop valves/Angle valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated with long shank and cup complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repair kitchen sinks of stainless steel 1mm thick with drainage board with plugs,washer and waste coupling ;including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm X 460mm and bowl size 410mm X 330mm X 160mm complete ,all as specified by Engr-in-charge

Supplying and fixing in repairs Vitreous China Wash down water closet (Pedestal pattern), complete white with integral footrest complete all as specified and directed by Engineer-in-Charge. Note : The quoted rate shall include provision of "P" Cast Iron trap.

Supplying and fixing in repairs Vitreous China squatting pan of “Orissa Pattern” of size 580x440mm white with integral footrest complete all as specified and directed by Engineer-in-Charge. Note : The quoted rate shall include provision of "P" Cast Iron trap.

10 ltr capacity PVC valveless, syphonic action dual flush type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, 32 mm dia flush pipe complete all as specified and directed by Engineer-in-Charge.

Vitreous China EWC one piece water closet pan type of size 380 mm x 655mm x700 mm white with and including seat cover,flush cistern 10 ltr capacity,connection pipe,P or S trap (closed pattern incl all necessary accessories like rag bolts,kit/gel gaskets,CP jet with connector pipe ,fixing bolts complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs Vitreous China Urinal, half stall type, size 355x340x535 mm white including flushing spray, flush pipe,32 mm dia CP waste coupling and 60 cm waste pipe complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs vitreous china wash hand basin white oval type over and including RCC counter with granite ,of size 470x470x110mm including galvanised iron brackets , chromium plated waste coupling, waste pipe etc., (incl all waste fittings) complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs vitreous china wash hand basin white with pedestal ,flat back of size 550x440mm including galvanised iron brackets , chromium plated waste coupling, waste pipe etc., (incl all waste fittings) complete all as specified and directed by Engineer-in-Charge.

Supply and fixed in repair brass chromium plated, towel ring, 150mm dia complete all as specified and directed by Engineer-in-Charge.

Supply and fixed in repair Soap dish, vitreous China white, approximate size 160x 160x90mm fixed to wall with stainless steel screws complete all as specified and directed by Engineer-in-Charge.

Supply and fixed in repair Soap dish, vitreous China white, approximate size 160x 160x90mm fixed to wall with stainless steel screws complete all as specified and directed by Engineer-in-Charge.

Supply and fixed in repair toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws complete all as specified and directed by Engineer-in-Charge.

PVC connections 15mm size with PTMT nuts of length 600 mm fixed in repair complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs waste pipe 32 mm dia,800 mm long flexible for Sink and WHB complete all as specified and directed by Engineer-in-Charge.

Stainless steel grating 110mm dia with locking system complete all as specified and directed by Engineer-in-Charge.

Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed by Engineer-in-Charge.

Health faucet chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed by Engineer in Charge.

Supply and fixed in repair towel Rail 450mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms)s complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs shelf of PTMT 450mm x124 mm fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed by Engineer-in-Charge.

PVC (SWR) trap ‘P’ or ‘S’, including jointing with solvent cement 100 mm bore fixed in repair complete all as specified and directed by Engineer in Charge.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm bore fixed in repair including jointing to waste pipe in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer in Charge.

75mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with and including MS clamps made out of flat iron of size 25 mm x 3 mm including nuts,bolts complete all as specified and directed by Engineer-in-Charge.

110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with and including MS clamps made out of flat iron of size 25 mm x 3 mm including nuts,bolts complete all as specified and directed by Engineer-in-Charge.

PVC(SWR) bends (any radius), for 75 mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

PVC(SWR) bends (any radius), for 110mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

PVC (SWR) junction (Single T) equal or unequal for 75 mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

PVC (SWR) junction (Single T) equal or unequal for 110 mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

CPVC(SDR-11) of outer dia 20 mm with and including CPVC SDR-11 fittings on walls and ceilings or laying in floors complete all as specified and directed by Engineer-in-Charge.

CPVC(SDR-11) of outer dia 16 mm with and including CPVC SDR-11 fittings on walls and ceilings or laying in floors complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 brass elbow fittings, ISI marked for CPVC pipe outer diameter 16 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 brass elbow fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 brass TEE fittings, ISI marked for CPVC pipe outer diameter 16 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 brass TEE fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 brass UNION fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 brass UNION fittings, ISI marked for CPVC pipe outer diameter 16 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 Tank Adaptor nipple fittings, ISI marked for CPVC pipe outer diameter 15 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 Tank Adaptor nipple fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 Ball valve fittings, ISI marked for CPVC pipe outer diameter 15 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 Ball valve fittings ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 Female Brass Threaded Adaptor (FTA/ FBTA) fittings, ISI marked for CPVC pipe outer diameter 15 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 Female Brass Threaded Adaptor (FTA/ FBTA) fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

Removing of spoil to a distance exceeding 500 but not exceeding 1500 metre and depositing where directed at a level not exceeding 1.5m above the starting point complete, all as specified and directed by Engineer-in-Charge.

INTERNAL ELECTRIC SUPPLY WORKS

Taking down Copper/Aluminium point wiring (light, fan, socket or power) complete, any type / size complete with removing all connection and accessories, fittings and fixtures such as switches , sockets, ceiling rose,pendent holder,fan regulator any type , all type of tube light fitting , batten , steel or PVC conduit , casing caping etc compele and making good the disturbed surface of wall , floor etc. complete all as specified and directed by Engineer-in-Charge. Note :-- Rates for cutting/chases in walls and making good disturbed area deemed to be included in the quoted rate

Taking down existing unserviceable sub main wiring with 2 Runs/4 Runs of 2.5/4/6 Sqmm aluminum/copper cable all as directed by Engr-in-charge.

Point wiring using approved colour coding as per IS ,with stranded copper conductor 1.5 sqmm (nominal area ) single core , flame retardant low smoke and low halogen FRLSH PVC insulated unsheathed , 1100 V grade conforming to IS 694 ,marked TEC and FIA approved in and including PVC conduit medium grade ISI marked 20mm dia with all fittings and accessories, concealed type/ surface type (surface type only on ceiling), PVC junction boxes, modular metal sunken/flush boxes of any modules from 2 to 18 Modules with Inner and outer modular cover plates, including FRLSH flame retardant low smoke and low halogen rigid PVC insulated unsheathed stranded copper conductor 1.5 Sqmm (nominal area )single core cable as earth continuity conductor to common earth and connected to earth dolly complete all as specified and directed by Engr-in-charge. Note :- 1. Cutting/chasing of wall etc. deemed to be included in the quoted rate of this item. 2. Modular metal flush/sunken Box along with modular switch/socket cover plate & sheet are inclusive in the item rate quoted. 3. Only switch socket and fan regulators to be measured and paid separately

(a) One light point controlled by one switch or one (Ceiling/ Wall/ Exhaust) fan point controlled by one switch and regulator

(b) One 3 pin 5 Amps socket outlet on independent board

(c ) One 3 pin 5 Amps socket outlet on same board with other switches

(d) One light point controlled by two, two way switches.

(e) One bell/buzzeer point controlled by one bell push.

Point wiring using approved colour coding as per IS ,with stranded copper conductor 2.5 sqmm (nominal area ) single core , FRLSH flame retardant low smoke and low halogen PVC insulated unsheathed , 1100 V grade conforming to IS 694 ,marked TEC and FIA approved in and including PVC conduit medium grade ISI marked 20mm dia with all fittings and accessories, concealed type/ surface type (surface type only on ceiling), PVC junction boxes, modular metal sunkun/ flush boxs of any modules from 2 to 18 Modules with Inner and outer modular cover plates, including FRLSH flame retardant low smoke and low halogen rigid PVC insulated unsheathed stranded copper conductor 2.5 Sqmm (nominal area )single core cable as earth continuity conductor to common earth and connected to earth dolly complete all as specified and directed by Engr-in-charge. Note :- 1. Cutting/chasing of wall etc. deemed to be included in the quoted rate of this item. 2. Modular metal flush/sunken Box along with modular switch/socket cover plate & sheet are inclusive in the item rate quoted. 3. Only switch, socket and fan regulators to be measured and paid separately

Point wiring using approved colour coding as per IS ,with stranded copper conductor 4 sqmm (nominal area ) single core , FRLSH flame retardant low smoke and low halogen PVC insulated unsheathed , 1100 V grade conforming to IS 694 ,marked TEC and FIA approved in and including PVC conduit medium grade ISI marked 20mm dia with all fittings and accessories, concealed type/ surface type (surface type only on ceiling), PVC junction boxes, modular metal sunkun/ flush boxs of any modules from 2 to 18 Modules with Inner and outer modular cover plates, including FRLSH flame retardant low smoke and low halogen rigid PVC insulated unsheathed stranded copper conductor 4 Sqmm (nominal area )single core cable as earth continuity conductor to common earth and connected to earth dolly complete all as specified and directed by Engr-in-charge. Note :- 1. Cutting/chasing of wall etc. deemed to be included in the quoted rate of this item. 2. Modular metal flush/sunken Box along with modular switch/socket cover plate & sheet are inclusive in the item rate quoted. 3. Only switch, socket and fan regulators to be measured and paid separately

Modular snap Switch one way 6 Amps one module complete all as specified and directed.

Modular snap Switch two way 6 Amps one module complete all as specified and directed.

Modular snap Switch one way 16 Amps one module complete all as specified and directed.

Modular Socket 6 Amps 5 Pin 2 Module complete all as specified and directed.

Modular Socket 6/16Amps 5 Pin 2 Module complete all as specified and directed.

Modular blanking plate suitable for 1 Module complete all as specified and directed

Modular fan Regulator step electronic type 2 module complete all as specified and directed.

Modular Bell Push 6 Amps one module complete all as specified and directed.

Ceiling rose surface backlite 65 x 20mm size three terminalcomplete all as specified and directed.

Lamp holder, PVC/ Polycarbonate type with back plate complete all as specified & directed.

Electric bell AC, ding-dong type, 230 Volt, single pole complete all as specified and directed.

LED lights fitting 1x 20 Watt, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose including 20 watt LED tube rod complete all as specified and directed.

Surface mounted wall mirror LED light Compact & sturdy 10 watt LED decorative fixture with anti glare polycarbonate diffuser, multi purpose lighting solution & applications .all accessories & fixtures, internally prewired and connecting by providing copper flexible wire 23/.0076 mm twin core upto fitting, complete all as specified and directed.

10W Bulk head LED luminaries Die cast aluminium alloy body ,heat resistent prismatic glass cover ,with specially designed gasket incl all accessories & fixtures, internally prewired and connecting by provding copper flexible wire 23/.0076 mm twin core upto fitting, complete in all respects complete all as specified and directed by Engineer-in-Charge.

15 watt recessed mounting downlight 2 x2 ft decorative type incl all accessories & fixtures, internally prewired and connecting by provding copper flexible wire 23/.0076 mm twin core upto fitting, complete in all respects complete all as specified and directed by Engineer-in-Charge.

Security Light LED 45 Watt made up of pressure dia cast Alumunium housing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including sevice bracket of GI pipe 32mm bore medium grade of length 0.9 mtr with MS clamps, bolts, nuts, and washers and suitable reducer for connecting fitting to GI pipe as required as site and making electrical connection, complete all as specified and directed.

Sub main wiring using approved colour coding as per IS with two runs of 6 sqmm PVC insulated, unsheathed cable FRLSH, flame retardant low smoke and low halogen 1100 volts grade , ISI marked with multistranded copper conductor with one run of 4 sqmm (green colour) PVC insulated, unsheathed cable FRLSH, flame retardant low smoke and low halogen 1100 volts grade , ISI marked with multistranded copper conductor as earth wire connected to common earth dolly with thimbles, drawing into & including PVC Concealed conduit ISI marked with all accessories on walls and making good of disturbed surfaces including all conduit fittings, clamps, gutties etc all as specified and directed. Note: (i) Two runs ( main ) of 6.00 sqmm cable,One run ( main ) of 4.00 sqmm cable together with conduit shall be considered as 1 running meter for payment purpose.

Sub main wiring using approved colour coding as per IS with two runs of 10 sqmm PVC insulated, unsheathed cable FRLSH, flame retardant low smoke and low halogen 1100 volts grade , ISI marked with multistranded copper conductor with one run of 6 sqmm (green colour) PVC insulated, unsheathed cable FRLSH, flame retardant low smoke and low halogen 1100 volts grade , ISI marked with multistranded copper conductor as earth wire connected to common earth dolly with thimbles, drawing into & including PVC Concealed conduit ISI marked with all accessories on walls and making good of disturbed surfaces including all conduit fittings, clamps, gutties etc all as specified and directed. Note: (i) Two runs ( main ) of 10.00 sqmm cable,One run ( main ) of 6.00 sqmm cable together with conduit shall be considered as 1 running meter for payment purpose.

Vertical Distribution Board iron clad, double door with IP-43 1K-09 protection suitable for MCCB as incommer and MCB as outgoing 415 Volts 3 phase 50 C/S 4 way, complete with appropriate size copper bus bar and neutral link complete with one MCCB 3 pole 415 Volts 125 Amps rating with rupturing cap 16 KA of the same make as of distribution board & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site or directed by Engr-in-Charge.

Distribution Board double door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, 8 way SPN, 415 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc flushed on the existing wall , to match with existing surface and making all necessary connections complete all as specified and directed.

SPN AFDD 16A/32A/40A offering protections for overload, short circuit, Residual current characterisitics TYPE A, Over Voltage protection above 270 AC plus minus 5% & series parallel arc fault. AFDD must be dual test button for AFDD and Earth leakage functions along with single diagnostic LED with blinking patterns for continuous ON, Series Arc, Parallel arc and overvoltage protection complete all as specified and directed.

Portable current residual device (PRCD) 16 A 30mA Euro II all as specified and as directed by Engr in charge.

MCB SPN 40-63 Amp,240 volts,50Hz, 10KA, 'C' series ISI marked as incoming and outgoing controlling circuit all as specified and directed.

MCB SP 6- 32 Amps, 220 volts , 50 Hzs, 10 KA , "C" series, ISI marked all as specified and directed.

Exhaust fan 300 mm sweep metal body, heavy duty, Single phase AC 230/240V, with energy efficient motor, pre lubricated double ball bearing, speed 900 rpm complete with louvers for wall mounting including grouting,making hole in the wall (Square/Round) as feasible grouting and holding down bolts, nuts, washers and provision of flexible copper conductor cable 3 core from ceiling rose to exhaust fan incl cutting of hole of required size for fixing of the exhaust fan complete all as specified and directed

Dismantling of ceiling fans,scrapping of old paint,Painting of ceiling fans complete, in situ with two coats of synthetic enamel paint over a coat of anti- corrosive zinc red oxide by spraying including filling cavities with filler, one coat after cleaning all dust etc,replacement of rubber bush,nuts,bolts,washers,split pin,down rod,copper flexible cable all as specified and directed.

Excavation in trenches in any type of soil not exceeding 1.50 meter wide and not exceeding 1.5 meter in depth; for foundation or for shafts, wells, cesspits, manholes, pierholes, etc. not exceeding 10 sq. m on plan and getting out complete all as specified.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick each,excavated soil in soft/loose soil, complete, all as specified and directed by Engineer-in-Charge.

Removing of surplus soil/ excavated material to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5m above the starting point complete, all as specified and directed by Engineer-in-Charge.

Clean dry sand laid in trenches/ducts for bedding and cushioning to cable, 8cm in depth before laying the cable and 15 cm in depth after laying the cable including spreading, levelling and consolidation complete all as specified and directed. Note : Consolidated/punned sand shall be measured for payment purpose.

Supply and laying burnt bricks sub class "B" old size for cable protection laid flat length perpenducualr to the axis of cable complete all as specified and direted by Engineer-in-Charge.

Earthing complete with and including galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm surrounded by a mixture of charcoal and salt in alternate layers burried directly in ground vertically in a pit of depth not less than 2.25 m deep below ground level with top edge of earth plate at a depth of not less than 1.5 m below ground level, connected with and including galvanised iron or steel earth wire, 4mm dia (No. 8 SWG) by means bolts, nuts, check nuts and washers made out of galvanised iron, 15 mm bore (light grade) GI pipe for protection of earthing lead, 20 mm bore (light grade) GI pipe for watering with funnel, wire mesh and including necessary excavation and earth work, PCC 1:2:4 type B-1 pit and 50 mm thick RCC M-25(Design mix) reinforced with XPM (weight not less than 3 kg/sq m) pit cover, C.I frame, charcoal and comman salt filling in alternate layers, complete all as shown and specified in electrical plate No. 3 of SSR Part-I (2009) complete all as shown on drawings and as specified and directed by Engineer-in-Charge. Note : The unit rate includes for protecton pipe 15mm and GI earth strip 4mm from top of earth plate upto 7.50 metre above ground level.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cables (heavy duty) cross sectional area 95 sq. mm, 3.5 core,stranded aluminium conductor including cable glands, cable lugs etc , to suit the cable size, 1100 volt grade, ISI marked, laid in trenches or fixing along the poles or passing through the pipes or laid under floors or through walls/ducts etc. complete all as specified.

Note: For the purpose of arriving at lumpsum amount, the amount of credit schedule i.e Sch 'A' section II (i.e Rs 1,20,350.00 shall be deducted from the total amount arrived.

Total of Schedule 'A' Rs.

M/s Super Trading Corporation (BID ID -3264782)

KUMAR AND COMPANY (BID ID -3259450)

SHRI GANESH CONSTRUCTION CO. (BID ID -3264142)

N.N.CONSTRUCTION (BID ID -3264829)

MANDEEP ENTERPRISES (BID ID -3264630)