540 Construction work of Dev Bhumi Rajat Jayanti Park in ward no. 01 Nagar Panchayat Dineshpur

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

Sand filling in plinth including supply of necessary quantity of Sand from a distance not exceeding 8km from the site of work & including Watering dressing etc. Rate to include cost of all materials, labour and T & P etc. required for proper completion of the work.

C.C. 1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

RCC as above but for RCC beams & slab in 1:1½:3.

Mild steel or iron in plain work such as in reinforced concrete or reinforced brick work wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage. Bend hooks and authorized overlapping shall be measured.

15 mm cement plaster on rough side of single or half brick wall of mix:. 1:6 (1 cement: 6 coarse sand)

12 mm. thick plaster with cement mortar consisting of 1part cement and 3 part of approved coarse sand. Minimum thickness not to be less than 10 mm. including supply of all materials, labour and T & P etc. required for proper completion of work.

Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete.

One priming coat of cement primer and one coat oil distemper on new work including supply of all materials, labour and tools and plants etc. required for proper completion of the work.

Shuttering and centering for Sup. Structure all required work including all cost of T & P etc. complete work as per building specification and direction of E/I.

Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Mild steel or iron in plain work in heavy size such as trusses, built up gates record racks , roof works gates etc.wrought to requre from including drilling holes riveting or wending whewre necessary and their fixing required for proper completion of work.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture

RUBBER MAT

Providing and fixing Neelgiri/Mexican grass turf with earthy 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light, watering with sprinkler and maintenance for 30 days or more till the grass establish properly as per direction of officer incharge. (dsr 2020 Holticulter)

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineerin- charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

Sand filling in plinth including supply of necessary quantity of Sand from a distance not exceeding 8km from the site of work & including Watering dressing etc. Rate to include cost of all materials, labour and T & P etc. required for proper completion of the work.

C.C. 1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-iii) derived from natural sources : 3 graded stone

RCC as above but for RCC beams & slab in 1:1½:3.

Mild steel or iron in plain work such as in reinforced concrete or reinforced brick work wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage. Bend hooks and authorized overlapping shall be measured.

15 mm cement plaster on rough side of single or half brick wall of mix:. 1:6 (1 cement: 6 coarse sand)

12 mm. thick plaster with cement mortar consisting of 1part cement and 3 part of approved coarse sand. Minimum thickness not to be less than 10 mm. including supply of all materials, labour and T & P etc. required for proper completion of work.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

One priming coat of cement primer and one coat oil distemper on new work including supply of all materials, labour and tools and plants etc. required for proper completion of the work.

Shuttering and centering for Sup. Structure all required work including all cost of T & P etc. complete work as per building specification and direction of E/I.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete With float glass panes of 5 mm thickness (weight notless than 12.50 kg/ sqm) as per the architectural drawings and the directions of engineer-in-charge .

Providing fixing thermal insulation of ceiling (under deck insulation)with Resin Bonded Fibre glass wool conforming to IS : 8183, density 24kg / m3, 50mm thick, wrapped in 200 G Virgin Polythene bags,fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of building.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300mm or more (thickness to be specified by the manufacturer), of 1stquality conforming to IS : 15622, of approved make, in all colours, shadesexcept White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter)

Providing and fixing white vitreous china pedestal type (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

NAHANI TRAP

Providing and fixing C.P. brass angle valve 15mm dia. for basin mixer and geyser points of approved quality conforming to IS 8931 (DSR.-2019) 18.53.1.

Providing and fixing C.P. brass stop cock 15mm dia(concealed) standerd design make conforming to IS 8931 (DSR.-2019) 18.52.1.

Providing and fixing white vitreous china wash basin size White Vitreous China Flat back wash basin size 630x450 mm with single 15 mm C.P. brass pillar tap, single 15mm C.P. brass pillar taps 32 mm C.P. brass waste of standard pattern, including painting of fitting and brackets, cutting and making good on walls floors wherever required.

Providing and fixing CPVC pipes 100 mm. dia having thermal stability for hot &cold water supply including all CPVC plain & brass threaded fitting this includes jointing of pipes & fitting with one step CPVC solvent cement, trenching refilling, & testing of joints complete as per direction of in charge..

Providing and fixing CPVC pipes 32mm. dia having thermal stability for hot &cold water supply including all CPVC plain & brass threaded fitting this includes jointing of pipes & fitting with one step CPVC solvent cement, trenching refilling, & testing of joints complete as per direction of in charge..

Providing and fixing CPVC pipes 20mm. dia having thermal stability for hot &cold water supply including all CPVC plain & brass threaded fitting this includes jointing of pipes & fitting with one step CPVC solvent cement, trenching refilling, & testing of joints complete as per direction of in charge..

Providing and fixing gun metal gate valve 32mm dia with C.I. wheel of approved quality (screwed end)

Providing and fixing gun metal gate valve 20mm dia with C.I. wheel of approved quality (screwed end)

water tanks 500 L.Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS :12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm. diameter, 1.8 m long complete With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 as per standard design.

Wiring point for light/fan point/exast fan point with 1.5 sq.mm FRLS PVC insulated copper single core cable in surface /recessed steel conduit, with piano type switch fenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper single core cable etc. as required. Group A

Wiring for light/power plug with 4 sq. mm FRLS PVC insulated copper conductore single core core cable in surface /recessed steel conduit, alongwith 2Nos. 4sq. mm FRLS PVC insulated copper single core cable for loop earthing etc. as required.

Earthing with G.I. earth pipe 4.5 meter long,40mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc with charcoal/coke and salt as required.etc.

Providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connection etc. as required..

Supply and fixing of 4way (4+12) double door ways surface/recess mounting, vertical type, 415V TPN MCB distribution board of sheet steel, dust protected ,duly powder painted inclusive of 200 A. tinned copper bus bar common natural link, earth bar din bar for mounting MCBs as required.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

Sand filling in plinth including supply of necessary quantity of Sand from a distance not exceeding 8km from the site of work & including Watering dressing etc. Rate to include cost of all materials, labour and T & P etc. required for proper completion of the work.

C.C 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

R.C.C. work with cement approved coarse sand and 2 cm. guage approved stone ballast in the proportion 1:1.5:3 in raft foundation and footing, RCC beams & slab lintel of the doors and windows, excluding supply of reinfocement & its bending but including its fixing and binding the same with 24 B.W.G. G.I. binding wire & including necessary centring & shuttering etc. and also including s/o all materials required for proper completion of the work. Binding wire to be supplied by the contractor free of cost.

Mild steel or iron in plain work such as in reinforced concrete or reinforced brick work wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage. Bend hooks and authorized overlapping shall be measured.

12 mm. thick plaster with cement mortar consisting of 1part cement and 6 part of approved coarse sand. Minimum thickness not to be less than 10 mm. including supply of all materials, labour and T & P etc. required for proper completion of work.

Shuttering and centering for Sup. Structure all required work including all cost of T & P etc. complete work as per building specification and direction of E/I.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

One priming coat of cement primer and one coat oil distemper on new work including supply of all materials, labour and tools and plants etc. required for proper completion of the work.

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

Providing and laying in position machine batched and machine mixed design mix

M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per as per clause 1500 & 1700 of MoRT&H specification including all material, labour, machinery .“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Foundations, footings, bases of columns, etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platform

Coursed rubble masonry (second sort) with hard stone in foundation & plinth with :7.7.1 Cement mortar 1:6 (1 cement : 6 coarse sand)

Coursed rubble masonry with hard stone (first or second sort) in superstructure above plinth level and upto floor five level. Masonry work (first sort), in cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand)

12.52 Providing and fixing tiled false ceiling of specified materials of size 12.52.3 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI

PVC WARD LIGHTS