Balance Work for Development of Taluk Hospital Kottarakkara, Kollam District, Kerala State along with all associated MEP Services and Utilities for Health and Family Welfare Department, Govt. of Kerala.

Amount

CIVIL, ROAD, SITE DEVELOPMENT & PLUMBING WORKS

2.1.1 : Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, disposed soil to be levelled and neatly dressed:All Kinds of soil

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil.

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil.

2.10.1.1 : Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil. and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m:All kinds of soilPipes, cables etc, not exceeding 80 mm dia.

2.10.1.2 : Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil. and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m:Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

2.26.1 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

2.33.2 : Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.Beyound 60 cm girth up to and including 120 cm girth

2.33.3 : Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.Beyond 120 cm girth up to and including 240 cm girth

3.3 : Excavation for road way in soil with Dozer including cutting and pushing the earth to site of embankment upto a distance of 100 metres (average lead 50 metres), including trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections.

4.1.3 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.1.B.1 : Construction of granular sub-base by providing graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401. Grading-V - For sub base cum drainage layer - Mix in Place Method

4.2.3 : Providing and laying cement concrete in retaining walls, return walls, walls ( any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing:1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

4.12 : Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification .

4.12 : Providing, laying, spreading and compacting graded stone aggregate to Wet Mix Macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.1.a : Providing and applying primer coat with bitumen emulsion ( SS) on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 - 1.0 kg/sqm using mechanical means.

5.2.a : Providing and applying tack coat with bitumen emulsion( RS) using emulsion pressure distributor at the rate of 0.20 - 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.

5.3.2.a : Providing and laying bituminous macadam with 80-100 TPH hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with bituminous binder (VG 30), transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction.For Grading II - (19 mm nominal size)

5.6.1.a : Providing and laying bituminous concrete with 80-100 TPH hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder( NRMB) @ 5.2 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects For Grading - I ( 19 mm nominal size )

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.9.16.1 : Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide

5.9.18 : Centering and shuttering including strutting, etc. and removal of form for:Small surfaces such as cantilever ends, brackets and ends of steps, caps and bases to pilasters and columns and the like

5.9.19 : Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges

5.11.1 : Extra additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5m, for every additional height of 1 metre or part thereof (Plan area to be measured).Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

5.38 : Extra for R.C.C. /B.M.C/R.M.C. work above floor V level for each four floors or part thereof.

5.44.1 : Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self – centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in-Charge . (Material shall confirm to ASTM 6063).Floor Joint of 100 mm gap.

5.45.1 : Providing and fixing of expansion joint system related with wall joint (internal/external) location as per drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221-02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063).Wall Joint of 100 mm gap.

5.46.1 : Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s preengineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. Material shall confirm to ASTM 6063.Roof Joint of 100 mm gap.

6.4.1 : Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in:Cement mortar 1:4 ( 1 cement : 4 coarse sand)

6.4.2 : Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in:Cement mortar 1:6 (1 cement : 6 coarse sand)

6.5 : Extra for brick work/ AAC block masonry/Tile brick masonry in super structure above floor V level, for each four floors or part thereof by mechanical means.

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

8.1.A : Construction of cement concrete kerb with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC Using Concrete Mixer on M-10 grade foundation 150 mm thick, foundation having 50 mm projection beyond kerb stone, kerb stone laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 409

8.2.2.1 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shadeArea of slab upto 0.50 sqm

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

8.3.2 : Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge.Granite work

8.4.11 : Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign with 7years warranty manufactured as per IRC :67 made of Type IV micro prismatic grade sheeting fixed over aluminium sheeting, 2 mm thick/ aluminium composit material sheeting 4 mm thick with suitable back supporting frame of MS angle 25x25x3 and supported on GI pipe pole 50mm NB confirming to IS 1239 firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc.75 cm triangle

8.4.12 : Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign with 7years warranty manufactured as per IRC :67 made of Type IV micro prismatic grade sheeting fixed over aluminium sheeting, 2 mm thick/ aluminium composit material sheeting 4 mm thick with suitable back supporting frame of MS angle 25x25x3 and supported on GI pipe pole 50mm NB confirming to IS 1239 firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc.50cmx 60 cm rectangular (Single chevron etc.)

8.5 : Extra for providing opening or required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

8.7.A : Providing and erecting overhead signs with retro reflectorised sign with 7 years warranty manufactured as per IRC67 made of Hign Intensity Micro Prismatic (Type IV ) grade sheeting fixed over corrosion resistant 2mm thick aluminium alloy sheet with vertical and lateral clearance given in clause 802.2 and 802.3 and installed as per clause 802.7 over a designed support system of aluminium alloy or galvanised steel trestles and trusses of sections and type as per structural design requirements and approved plansTruss and Vertical Support

8.10.2 : Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in Charge and finished smooth.Granite Stone of approved shade

8.11.2 : Painting lines, dashes, arrows etc on roads in two coats on new work with ready mixed road marking paint conforming to IS:164 on bituminous surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control Up to 10 cm in width

8.16 : Reinforced cement concrete M-15 grade boundary pillars of standard design as per IRC:25-19767, fixed in position including finishing and lettering but excluding painting .

8.20 : Providing, Fixing and erecting 50 mm dia GI pipe railing in 3 rows duly painted on Tubular Steel Railing on Medium Weight Steel Channel ( ISMC series) 100 mm x 50 mm, 1.2 metres high above ground, 2 m centre to centre, complete as per approved drawings including painting over suitable primer .

8.23.A : Providing and erecting a "W" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 811.3

8.31 : Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622(thickness to be specified by the manufacturer), of approved make, in all colours,shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge,in skirting, risers of steps and dados, over 12 mm thick bed of cementmortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @3.3kg per sqm, including pointing in white cement mixed with pigment of matchingshade complete.

8.35 : Providing and fixing reflective road studs (Raised Pavement Marker) of ' category A' made out of ASA/HIPS/ABS moulded body with shanks and conforming to ASTM D 4280, strong enough to support a load of more than 13.635 T when tested in accordance with ASTM D 4280, reflective panel confirming to ASTM D 788, and reflectivity conforming to clause 804.4. including installation, drilling, fixing with adhesive etc. with 2 years warranty for the road stud as well as for in field performance as per clause 804.7.3 Road Markers/Road Stud with Lense Reflector :-

9.1.1 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood

9.20.2 : Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of I st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

9.24.1 : Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded ) (overall area of door shutter to be measured):Rectangular or square

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

9.53 : Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

9.60.1 : Providing and fixing oxidised M.S. double acting spring hinges with necessary screws etc. complete.150 mm

9.62.2 : Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete:250x16mm

9.70.1 : Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete:125x64x1.90 mm

9.76 : Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

9.84 : Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

9.90.1 : Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete.Size 40 mm

9.92.1 : Providing and fixing chromium plated brass handles with necessary screws etc. complete:125 mm

9.96.1 : Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:300x16 mm

9.97.1 : Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:300x10 mm

9.97.3 : Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:200x10 mm

9.97.5 : Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:100x10 mm

9.100.1 : Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:125 mm

9.101.2 : Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper

9.103 : Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS: 1868) aluminium lever handles of approved quality with necessary screws etc . complete.

9.105.1 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.75 mm overall thickness partition with 12.5 mm thick double skin fire rated board conforming to IS : 2095 : part I

9.105.2 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.75 mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum board conforming to IS : 2095 : part I

9.105.3 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.66 mm overall thickness Partition with 8 mm thick double skin Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process with Compressive Strength 225 kg/sq cm, Bending Strength 100 kg/sq cm

9.105.5 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.66 mm overall thickness partition using 8 mm thick double skin multipurposecement bonded wood particle board manufactured as per IS: 14276 with suitablecement bonded board screws

9.114.1 : Providing and fixing magnetic catcher of approved quality in cupboard/ward robe shutters, including fixing with necessary screws etc. complete.Triple strip vertical type

9.116 : Providing and fixing sliding arrangement in racks/ cupboards/cabinets shutter by with stainless steel rollers to run inside C or E aluminium channel section ( The payment of C or E channel shall be made separately

9.121 : Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross- section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminated shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

9.122.2 : Providing and fixing to existing door frames.30 mm thick Fiberglass Reinforced Plastic (F.R.P) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) / Polystyrene foam to be used all filler material throughout the hollow panel, casted monoolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS : 14856, complete as per direction of Engineer-in-charge.

9.139 : Providing and fixing panic bar / latch (Double point ) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer -in-charge, all complete.

9.157.1 : Providing and fixing Pre-laminated medium density fibre board IS:14587:1998 marked, with one side decorative lamination other side balancing lamination Grade-I (exterior grade) in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be paid separately).Pre-laminated with decorative lamination one side and other side balancing laminaion exterior Grade-I MDF Board 18mm thick confirming to IS:14587.

9.157.2 : Providing and fixing Pre-laminated medium density fibre board IS:14587:1998 marked, with one side decorative lamination other side balancing lamination Grade-I (exterior grade) in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be paid separately).Pre-laminated with decorative lamination one side and other side balancing lamination exterior Grade-I MDF Board 25mm thick confirming to IS:14587.

9.158.1 : Providing and fixing in wall lining medium density fibre board IS: 14587: 1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete.12 mm thick.

9.161 : Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontalside & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mmthick GI sheet ( Zinc coating not less than 120gm/m2) suita2ble for mounting 120min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineralwool Insulation having density min 96Kg/m2 . The frame will have a provision ofG.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style ofsize M10 x 80 ) suitable for fixing in the opening along with Factory madeTemplate for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire ratedglazed shutter . The frame shall be finished with a approved fire resistant primeror Powder coating of not less than 30 micron in desired shade as per thedirections of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded

9.162 : Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 minFire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certifiedas per laboratory approved by Engineer-in-charge, with suitable mounting ondoor frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mmwide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet(zinc coating not less than 120gm/m²) duly filled mineral wool insulation havingdensity min 96 kg/m³ and fixing with necessary stainless steel ball bearing hingesof size 100x89x3mm of approved make, including applying a coat of approvedfire resistant primer or powder coating not less than 30 micron etc all completeas per direction of Engineer-in-charge (panelling to be paid for seperately

9.164 : Providing and fixing glazing in fire resistant door shutters, fixed panels & partitionsetc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mmfrom the edges and 150 mm c/c , including applying a coat of approved fire resistantprimer/powder coating of not less than 30 micron on G.I. beading, & special ceramictape of 5 x 20 mm size etc complete in all respect as per direction of Engineer-incharge.The glass shall be clear, toughened, interlayered, non-wired fire resistant having11 mm thickness of approved brand with 120 minutes of fire resistance both integrity &radiation control (EW120) and minimum 15 min of insulation (EI15) and having a soundreduction of ?37dB and LT of 86%. Glass shall be compliant to class 2(B)2 category ofImpact Resistance as per EN 12600. The glass should be manufactured in UL & TUVaudited Facility and including UL-EU Certification.The maximum glazing size cannotbe more than 1100 mm x 2200 mm (w x h) or 2.42 sq mts in total area. The test report forthe complete system (Glazed Door or Partition) will be considered valid only if it containsthe stamp and signature of the authorized signatory from the glass manufacturer.(Actual glass size is to be measured at site for payments).

9.165.1 : Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm

9.165.2 : Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.100mm

10.1 : Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

10.2 : Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

10.6.1 : Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

10.7 : Providing and fixing ball bearing for rolling shutters.

10.8.1 : Extra for providing mechanical device chain and crank operation for operating rolling shuttersExceeding 10.00 sqm and upto 16.80 sqm in the area

10.16.1 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

10.17 : Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

10.25.1 : Item Shifted to head 14 as item 14.74Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In stringers, treads,landings etc. of stair cases, including use of chequered plate wherever required, all complete

10.25.2 : Item Shifted to head 14 as item 14.74Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

10.28 : Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

11.3.1 : Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate)finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate

11.20.2 : Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand).Medium shade pigment using 50% white cement 50 % Grey cement

11.41.2 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

11.46.2 : Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

11.56.1 : Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

12.24.3.1 : Providing and fixing insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately):Flame retardant face insulating board12 mm thick

12.27.4.1 : Extra for Circular cutting including wastages in ceiling with:Flame retardant face insulating board12 mm thick

12.32 : Extra for sunk or raised mouldings in the plaster of Paris (Gypsum anhydrous) ceiling.Extra for sunk or raised mouldings in the plaster of Paris (Gypsum anhydrous) ceiling .

12.42.2.2 : Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansionSingle pushfit Coupler110 mm

12.42.5.2 : Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansionBend 87.5⁰110 mm bend

12.42.6.2 : Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansionShoe (Plain)110 mm Shoe

12.43.2 : Providing and fixing unplasticised- PVC pipe clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc. complete.110 mm

12.45.2 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum fire resistant board conforming to IS; 2095-Part I

12.45.3 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum moisture resistant board

12.46 : Providing and fixing to the inlet mouth of rain water pipe PTMT ( an Engineering Thermoplastic) grating square (Slit) 150 mm square with a height of 8 mm and weighing not less than 100 gms

12.53 : Providing and Fixing 15 mm densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture spintone /cosmos /Hexa or equivalent of size 595x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main 'T' runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross "T" of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main 'T' of size 24 x 28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main'T' at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross 'T' of length 600 mm and size 24x28 mm made of 0.33 mm thick (minimum) sheet to be inter locked at middle of the 1200x600 mm panel to from grid of size 600x600 mm, resting on periphery walls/partitions on a Perimeter wall angle pre-coated steel of size (24x24x3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture (Spintone / Cosmos/hexa) in the grid, including cutting / making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever require. Main 'T' runners to be suspended from ceiling using G.I slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size of 85x30x0.8 mm, spaced at 1200mm centre to centre along main 'T' bottom exposed with 24 mm of all T- sections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by by engineer-in-charge. Note:- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm. The calcium silicate ceiling tiles shall have NRC. value of 0.50 (Minimum), light reflection > 85% non - combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity < 0.043 w/m 0 KC.

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.1.2 : 12 mm cement plaster of mix:1:6 (1 cement : 6 fine sand).

13.4.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 coarse sand)

13.7.1 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

13.16.1 : 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

13.22 : Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

13.28.2 : 12 mm thick plain cement mortar bands in cement mortar 1:4 ( 1 cement : 4 fine sand) :Sunk Band

13.28.3 : 12 mm thick plain cement mortar bands in cement mortar 1:4 ( 1 cement : 4 fine sand) :Raised Band

13.28.4 : 12 mm thick plain cement mortar bands in cement mortar 1:4 ( 1 cement : 4 fine sand) :Moulded Band

13.45.1 : Finishing walls with textured exterior pint of required shade:New work (Two or more coats applied @ 3.28 ltr/ 10 sqm ) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm

13.46.1 : Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

13.50.3 : Applying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron /steel works

13.52.2 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On concrete work

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.61.1 : Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.62.1 : Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture .

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.85.3 : Applying priming coats with primer of approved brand and manufacture, having low VOC ( Volatile Organic Compound) content.With water thinnable cement primer on walls surface having VOC content less than 50 grams / litre

15.2.1 : Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

15.7.4 : Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar

15.9.2 : Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in- Charges:In cement mortar

15.58 : Demolishing R.C.C. work by mechanical means and stockpiling at designated locations and disposal of dismantled materials up to a lead of 1 kilometre, stacking serviceable and unserviceable material separately including cutting reinforcement bars.

15.60 : Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

16.68 : Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

16.69 : Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge ( length of finished kerb edging shall be measured for payment ). ( Precast C.C. kerb stone shall be approved by Engineer-in-Charge)

16.70.2 : Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts , bolts and washers as required complete as per the direction of Engineer-in- charge.Made of G.I wire of dia 4 mm. PVC coated to achieve outer dia. not less than 5 mm in required colour and shade

16.75 : Providing and laying C.C pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator, vacuum dewatering process and finally finished by floating brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge ( The panel shuttering work shall be paid for separately)

17.1.1 : Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand Cast Iron P or S trap, 10 litter low level white P.V.C.flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever require:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

17.2.1 : Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid

17.4.1 : Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required:One urinal basin with 5 litre white P.V.C. automatic flushing cistern

17.7.4 : Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x400mm with single 15 mm C.P.brasspillar taps

17.10.1.1 : Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink with drain board510x1040 mm bowl depth 250 mm

17.10.2.1 : Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink without drain board610x510 mm bowl depth 200 mm

17.22A : Providing and fixing CP Brass 32mm size Bottle trap of approved quality & make and as per the direction of Engineer in charge.

17.22B : Providing and fixing CP Brass Single lever telephonic wall mixer of quality& make as approved by Engineer in charge.(a) 15 mm nominal dia

17.28.1.1 : Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC. waste fittings complete.Semi rigid pipe32 mm dia

17.31 : Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

17.32.4 : Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 1500x450 mm

17.34.1 : Providing and fixing toilet paper holder:C.P. brass

18.7.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall20 mm nominal outer dia pipes

18.7.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall25 mm nominal outer dia pipes

18.7.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall32 mm nominal outer dia pipes

18.7.5 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall40 mm nominal outer dia pipes

18.7.6 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall50 mm nominal outer dia pipes

18.8.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal outer dia pipes

18.8.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal outer dia pipes

18.8.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.32 mm nominal outer dia pipes

18.9.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work20 mm nominal outer dia pipes

18.9.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work25 mm nominal outer dia pipes

18.9.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work32 mm nominal outer dia pipes

18.9.5 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work40 mm nominal outer dia pipes

18.9.6 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work50 mm nominal outer dia pipes

18.9.7 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work62.50 mm nominal inner dia pipes

18.9.8 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work75 mm nominal inner dia pipes

18.15.2 : Providing and fixing brass bib cock of approved quality :20 mm nominal bore

18.16.2 : Providing and fixing brass stop cock of approved quality :20 mm nominal bore

18.17.1 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

18.17.2 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore

18.17.3 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :40 mm nominal bore

18.17.4 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore

18.17.5 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :65 mm nominal bore

18.18.2 : Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:20 mm nominal bore

18.18.3 : Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:25 mm nominal bore

18.19.2.1 : Providing and fixing gun metal non-return valve of approved quality (screwed end):32 mm nominal boreHorizontal

18.19.3.1 : Providing and fixing gun metal non-return valve of approved quality (screwed end):40 mm nominal boreHorizontal

18.19.4.2 : Providing and fixing gun metal non-return valve of approved quality (screwed end):50 mm nominal boreVertical

18.19.5.1 : Providing and fixing gun metal non-return valve of approved quality (screwed end):65 mm nominal boreHorizontal

18.19.5.2 : Providing and fixing gun metal non-return valve of approved quality (screwed end):65 mm nominal boreVertical

18.22.2 : Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet:150 mm diameter

18.49.1 : Providing and fixing C.P brass bib cock of approved quality conforming to IS: 8931.15 mm nominal bore

18.50.1 : Providing and fixing C.P brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore

18.51.1 : Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

18.52.1 : Providing and fixing C.P brass stop cock ( concealed) of standard design and of approved make conforming to IS: 893115 mm nominal bore

18.53.1 : Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

18.53A : Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) ofapproved make and quality as per direction of Engineer-in-charge.

18.63 : Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing not less than 85 gms

18.75.3 : Providing and fixing PTMT extension nipple for water thank pipe, fittings of approved quality and colour .25 mm nominal bore, weighing not less than 62 gms

18.77 : Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

18.78 : Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.Il pipe etc.

18.79 : Making hole up to 20x20 cm and embedding pipes up to 150 mm diameter in masonry and filling with cement concrete 1:3:6 (1 cement : 3 coarse sand 6 graded stone aggregate 20 mm nominal size) including disposal of malba.

19.7.1.1 : Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design:Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weigh of cover 23 kg and weight of frame 15 kg):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.7.1.2 : Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design:Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weigh of cover 23 kg and weight of frame 15 kg):With Sewer bricks conforming to IS : 4885

19.7.2.1 : Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design:Inside size 120x90 cm and 90 cm deep including C.I. cover with frame ( medium duty ) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg ( weight of cover 58 kg and weight of frame 58 kg):With common burnt clay F.P.S ( non modular) bricks of class designation 7.5

19.7.3.1 : Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design:Inside size 120x 90 cm and 90 cm deep including C.I. cover with frame ( heavy duty ) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg ( weight of cover 108 kg and weight of frame 100 kg)With common burnt clay F.P.S. ( non modular) bricks of class designation 7.5

19.8.1.1 : Extra for depth for manholesSize 90x80 cmWith common burnt clay F.P.S. ( non modular ) bricks of class designation 7.5

19.8.2.1 : Extra for depth for manholesSize 120x90 cmWith common burnt clay F.P.S. ( non modular ) bricks of class designation 7.5

19.15.1 : Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) as per standard design.With 20x20 mm square bar

19.18.1 : Supplying and fixing C.I with out frame for manholes:455 x 610 mm rectangular C.I cover ( light duty ) the weight of the cover to be no less than 23 kg

19.19.1.1 : Providing and fixing in position Pre-cast R.C.C. manhole cover and frame of required shape and approved quality.L D - 2.5Rectangular shape 600x450 mm internal dimensions

19.30.1.1 : Constructing brick masonry chamber for underground C.I. inpection chamber and bends with bricks in cement mortar 1:4 ( 1 cement: 4 coarse sand) C.I.cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23kg and weight of frame 15 kg), R.C.C top slab with 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:Inside dimensions 455x610 mm and 45 cm deep for single pipe line:With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.33 : Constructing soak pit 1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.

19.36.1 : Providing and laying Non Pressure NP-4 class (Heavy duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete.450 mm dia RCC pipes.

19.36.2 : Providing and laying Non Pressure NP-4 class (Heavy duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete.600 mm dia RCC pipes.

21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2 : For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.2.2 : Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides

21.3.1 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

21.3.2 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

21.4.1 : Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS: 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors including cost of cutting floors, embeding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer -in- Charge.With stainless steel cover plate minimum 1.25 mm thickness

21.5 : Providing and fixing powder coated aluminium work ( minimum thickness of powder coating 50 micron) consisting of tee /angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-Charge ( level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately ).

21.8.1 : Upto 5 mm depth and 5 mm width

21.12.2 : Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0mm thick & 2100 mm long with S.S. screws etc. complete as per direction of Engineer -in-Charge.Powder coated minimum thickness 50 micron aluminium tubular handle bar

21.13 : Providing and fixing 100 mm brass locks ( best make of approved quality ) for aluminium doors including necessary cutting and making good etc. complete

21.18 : Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge ( Door handle, lock and stopper etc to be paid separately)

22.4.2 : Providing and Placing in position suitable PVC water stops conforming to IS : 12200 for construction / expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete:Dumb bell with ventral bulb ( 180 mm wide, 8 mm thick)

22.5 : Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

22.6 : Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : a) after surface preparation, first layer of slurry of cement @ 0.488 kg/ sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. laying second layer of fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/ sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tilling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured)

22.22 : Providing and mixing integral crystalline admixture for waterproofing treatment toRCC structures like basement raft, retaining walls, reservior, sewage & watertreatment plant, tunnels / subway and bridge deck etc.. at the time of transportingof concrete into the drum of the ready-mix truck , using integral crystalline [email protected]% (minimum) to the weight of cement content per cubic meter of concrete)or higher as recommended by the manufacturer's specification in reinforced cementconcrete at site of work. The material shall meet the requirements as specified inACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 90%,compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostaticpressure. The crystalline admixture shall be capable of self-healing of cracks up toa width of 0.50mm. The work shall be carried out all complete as per specificationand the direction of the Engineer-in-charge. The product performance shall carryguarantee for 10 years against any leakage.

22.23.1 : Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin- charge. The product performance shall carry guarantee for 10 years against any leakage.For vertical surface two coats @0.70 kg per sqm

22.23.2 : Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin- charge. The product performance shall carry guarantee for 10 years against any leakage.For horizontal surface one coat @1.10 kg per sqm.

25.1 : Providing and supplying aluminium extruded tubular and other aluminium sectionsas per the architectural drawings and approved shop drawings , the aluminiumquality as per grade 6063 T5 or T6 as per BS 1474,including super durable powdercoating of 60-80 microns conforming to AAMA 2604 of required colour and shadeas approved by the Engineer-in-Charge. ( The item includes cost of material suchas cleats, sleeves, screws etc. necessary for fabrication of extruded aluminiumframe work. Nothing extra shall be paid on this account).

25.2 : Designing, fabricating, testing, protection, installing and fixing in position semi(grid) unitized system of structural glazing (with open joints) for linear as well ascurvilinear portions of the building for all heights and all levels, including:a) Structural analysis & design and preparation of shop drawings for the specifieddesign loads conforming to IS 875 part III (the system must passed the proof testat 1.5 times design wind pressure without any failure), including functional designof the aluminum sections for fixing glazing panels of various thicknesses, aluminiumcleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clampsetc., structural and weather silicone sealants, flashings, fire stop (barrier)-cumsmokeseals, microwave cured EPDM gaskets for water tightness, pressureequalisation & drainage and protection against fire hazard including:b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3Dimentional movement for achieving perfect verticality and fixing structural glazingsystem rigidly to the RCC/ masonry/structural steel framework of building structureusing stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetalliccontacts with nuts and washers etc. of stainless steel grade 316, of the requiredcapacity and in required numbers.c) Providing and filling, two part pump filled, structural silicone sealant and onepart weather silicone sealant compatible with the structural silicone sealant ofrequired bite size in a clean and controlled factory / work shop environment ,including double sided spacer tape, setting blocks and backer rod, all of approvedgrade, brand and manufacture, as per the approved sealant design, within and allaround the perimeter for holding glass.d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thickand of sizes, shapes and profiles, as required as per the site conditions, to seal thegap between the building structure and all its interfaces with curtain glazing tomake it watertight.e) Making provision for drainage of moisture/ water that enters the curtain glazingsystem to make it watertight, by incorporating principles of pressure equalization,providing suitable gutter profiles at bottom (if required), making necessary holesof required sizes and of required numbers etc. complete. This item includes costof all inputs of designing, labour for fabricating and installation of aluminium grid,installation of glazed units, T&P, scaffolding and other incidental charges includingwastages etc., enabling temporary structures and services, cranes or cradles etc.as described above and as specified. The item includes the cost of getting all thestructural and functional design including shop drawings checked by a structuraldesigner, dully approved by Engineer-in-charge.The item also includes the cost of all mock ups at site, cost of all samples of theindividual components for testing in an approved laboratory, field tests on theassembled working structural glazing as specified, cleaning and protection till thehanding over of the building for occupation. In the end, the Contractor shall providea water tight structural glazing having all the performance characteristics etc. allcomplete as required, as per the Architectural drawings, as per item description,as specified, as per the approved shop drawings and as directed by the Engineerin-Charge.Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extrudedaluminium section capping for fixing in the grooves of the curtain glazing andvermin proof stainless steel wire mesh shall be paid for separately under relevantitems under this sub-head. However, for the purpose of payment, only the actualarea of structural glazing (including width of grooves ) on the external face shallbe measured in sqm. up to two decimal places.Note:-2. The following performance test are to be conducted on structural glazingsystem if area of structural glazing exceeds 2500 Sqm from the certified laboratoriesaccreditated by NABL(National Accreditation Board for Testing and CalibrationLaboratories), Department of Science & Technologies, India. Cost of testing ispayable separately. The NIT approving authority will decide the necessity of testingon the basis of cost of the work, cost of the test and importance of the work.Performance Testing of Structural glazing systemTests to be conducted in the NBL Certified laboratories1. Performance Laboratory Test for Air Leakage Test (-50pa to – 300pa) & (+50pa to+300pa) as perASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr”2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testingmethod for a range up to 2000 ml.”3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01-05 testingmethod for a range upto 2000 ml”4. Structural Performance Deflection and deformation by static air pressure test(1.5 times desing wind pressure without any failure) as per ASTME-330-10 testingmethod for a range upto 50 mm”5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method forQualitative test” Tests to be conducted on site6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi)upto 2000ml”

25.4 : Extra for openable side / top hung vision glass panels (IGUs) including providingand supplying at site all accessories and hardwares for the openable panels asspecified and of the approved make such as heavy duty stainless steel frictionhinges, min 4 -point cremone locking sets with stainless steel plates, handles,buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts,washers etc. all complete as per the Architectural drawings, as per the approvedshop drawings, as specified and as directed by the Engineer-in-Charge.

25.5 : Providing,fabricating and supplying shadow box of required size and shape, for fixing in the spandrel portion of the structural glazing, in linear as well as curvilinear portions of the building by providing semi - rigid, inorganic, non- combustible fibre glass wool insulation 50 mm thick, conforming to IS: 8183 and BS: 3958 part 5. The insulation layer shall have facing (factory bonded on surface # 1 of the fibre glass insulation layer), of black non-woven fibre glass tissue of nominal thickness 0.5mm and nominal mass not less than 60 gm/ sqm, made of randomly oriented glass fibres distributed in a binder by a wet-lay process including fixing 1.5 mm thick solid aluminum sheet backing using, 6 mm thick cement board including SS rivets, nuts,bolts, washers etc complete.

25.6 : Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic float glass of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade so as to match the colour and shade of the IGUs in the vision panels etc., all complete for the required performance as specified, as per the architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineer- in - Charge. For payment, only the actual area of glass on face # 1 of the glass panels (but excluding the area of grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (Payment for fixing of Spandrel Glass panels in the curtain glazing is included in cost of relevent item*).(ii) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face #2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35%, Light reflection internal 10 to 15%, light reflection external 10 to 20%, shading coefficient (0.25 - 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

25.7 : Designing, fabricating, testing, installing and fixing in position Curtain Wall withAluminium Composite Panel Cladding, with open grooves for linear as well ascurvilinear portions of the building , for all heights and all levels etc. including:a) Structural analysis & design and preparation of shop drawings for pressureequalisation or rain screen principle as required, proper drainage of water to makeit watertight including checking of all the structural and functional design.b) Providing, fabricating and supplying and fixing panels of aluminium compositepanel cladding in pan shape in metalic colour of approved shades made out of4mm thick aluminium composite panel material consisting of 3mm thick FR grademineral core sandwiched between two Alumini um sheets (each0.5mm thick). Thealuminium composite panel cladding sheet shall be coil coated, with Kynar500based PVDF / Lumiflon based fluoropolymer resin coating of approved colourand shade on face # 1 and polymer (Service) coating on face # 2 as specified usingstainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backerrods etc.c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanisedwith serrations and serrated washers to arrest the wind load movement, fasteners,SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators toprevent bi-metallic contacts all complete required to perform as per specificationand drawing The item includes cost of all material & labour component, the cost ofall mock ups at site, cost of all samples of the individual components for testing inan approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wallwith aluminium composite panel cladding till the handing over of the building foroccupation. Base frame work for ACP cladding is payable under the relevantaluminium item.s The Contractor shall provide curtain wall with aluminiumcomposite panel cladding, having all the performance characteristics all complete, as per the Architectural drawings, as per item description, as specified, as per theapproved shop drawings and as directed by the Engineer-in-Charge.However, for the purpose of payment, only the actual area on the external face ofthe curtain wall with Aluminum Composite Panel Cladding (including width ofgroove) shall be measured in sqm. up to two decimal places.

30.2.2 : Supplying and stacking of good earth at site including royalty and carriage upto 5 k.m. lead complete (earth measured in stacks will be reduced by 20% for payment).

30.2.3 : Supplying and stacking sludge at site including royalty and carriage upto 5 k.m. lead complete (sludge measured in stacks will be reduced by 8% for payment).

30.2.4.1 : Supplying and stacking at site dump manure from approved source, including carriage upto 5 k.m. lead complete (manure measured in stacks will be reduced by 8% for payment) :Screened through sieve of I.S. designation 20 mm

30.2.7 : Fine dressing of the ground

30.2.8 : Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

30.2.9 : Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

30.2.25 : Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 5 k.m. lead complete (cattle manure measured in stacks will reduced by 8% for Payment).

30.2.57.1 : Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unsaverieable material?s as per direction of officer in charge (excluding cast of plant & water )Cost of plantation per trees plants (for 100 nos.=427.45/100)

30.2.57.2 : Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unsaverieable material?s as per direction of officer in charge (excluding cast of plant & water )Cost of plantation per Shrubs plants (for 200 nos.=427.45/200)

30.2.57.3 : Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unsaverieable material?s as per direction of officer in charge (excluding cast of plant & water )Cost of plantation per Hedge plants (for 300 nos.=427.45/300)

50.6.1.1 : Solid block masonry using pre cast solid blocks ( factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part 1 of 1979 for foundation and plinth with thickness 20 cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

50.6.1.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure above floor two level up to terrace level thickness 20cm and above in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

50.6.3.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

Hollow block masonry using pre cast solid blocks ( Factory made ) of size 40x20x10cm or nearest available size confirming to IS 2185 part I of 1979 for Super structure above floor two level upto terrace floor level for 10cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand ) including cost of scaffolding etc complete

50.9.15.1 : Supplying and fixing 200 mm Aluminium aldrop

50.12.2.4 : Providing & fixing Poly carbonate multi wall plain sheet 6 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12m or as decide by the Engineer in charge. The sheets shall be fixed using self drilling/self tapping screw of size (5.5x55mm) with EPDM seal complete upto any pitch in horizontal/vertical curved surfaces, but excluding the cost of purlins, rafters, trusses, and including cutting to size and shapes where ever required.

50.17.1.1 : Supplying and fixing Stainless steel soap dish including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

50.17.1.4 : Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge.

50.18.7.5.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 40 mm dia 6Kgf/cm2 - Internal work - Exposed on wall

50.18.7.6.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6 Kgf/cm2 - Internal work- Exposed on wall

50.18.8.5.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 40 mm pipe 6Kgf/cm2

50.18.8.6.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2

50.18.8.8.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 6 Kgf/cm2

50.18.8.9.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2

50.18.9.6.2 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 50 mm dia 6 Kgf/cm2

50.18.9.7.1 : Providing and fixing PVC pipes includings of pipes with one step PVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge. 63 mm dia 6Kgf/cm2

50.18.9.8.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 6 Kgf/ cm2

50.18.9.9.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

50.18.9.15.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 40 mm dia 6 Kgf/cm2 - External work - Exposed on wall

50.18.9.16.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6Kgf/cm2 - External work - Exposed on wall

50.18.9.17.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/ clip at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 63 mm dia 6 Kgf/cm2 - External work - Exposed on wall

50.18.9.18.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm2 - External work- Exposed on wall

50.18.9.19.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

50.18.9.21 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Elbow

50.18.9.21.2 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia 45 degree Elbow

50.18.9.21.3 : Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia Door Elbow

50.18.9.21.4 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Bend

50.18.9.21.5 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75x75x75 mm dia Tee

50.18.9.21.6 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75x75x75 mm dia Door Tee

50.18.9.21.7 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Vent cowl

50.18.9.21.8 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia End cap

50.18.9.21.9 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Socket /coupling

50.18.9.21.10 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75x63 mm dia Reducer

50.18.9.22.1 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow

50.18.9.22.2 : Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow

50.18.9.22.3 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement-110 mm dia Door Elbow

50.18.9.22.4 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend

50.18.9.22.5 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee

50.18.9.22.6 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x110 mm dia Door tee

50.18.9.22.7 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x75 mm dia Door Tee

50.18.9.22.8 : Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia Vent cowl

50.18.9.22.9 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia offset

50.18.9.22.10 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia End Cap

50.18.9.22.11 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Socket/ coupling

50.18.9.22.12 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x75 mm dia Reducer

50.18.78 : Making chases up to 12.5x12.5 cm in walls including making good and finishing with matching surface after housing pipe etc.

od168193/2024_2025 : Providing and fixing coloured vitreous china under counter round wash basin 440 mm dia or nearest size of approved make including one CP brass pillar cock 15 mm NB including connecting pipes with all fittings 32 mm dia rubber plugs 32 mm dia CP brass waste coupling, 32 mm dia CP brass bottle trap, 15mm angle valve, etc. complete as directed by the Engineer-in-charge.

od168195/2024_2025 : Supplying approved make PVC gully trap of size 160 x 110mm and CI grating 150mmx150mm size and light duty C.I cover with frames 300mmx300mm size(inside) the weight of cover to be not less than4.5kg and frame to be not less than2.7kg (CI MH cover and frame as per IS:1726) single sealed of size conveying to size the above mentioned items and constructing 30cmx30cm internal size gully trap chamber and depth upto 60cm,115 thk brick wall in CM 1:6 on a foundation of PCC 1:4:8.100mm thick plastering inside with CM 1:3,12mm thk with a neat cement flushing coat and conveying to site,cleaning ,installing and testing approved make PVC gully trap with 160mm outlet(Fabricated),surrounding with CC 1:1.5:3, 150x150mmm,top with CI grating above the PVC gulley trap and light duty CI cover and frame over the chamber including cost of all materials, etc complete as per approved drawing and as directed by Engineer-in- Charge.

od168196/2024_2025 : Providing and fixing stainless steel grating of approved quality and colour.Circular type100 mm nominal dia

od229177/2024_2025 : Providing and fixing floor trap of PVC,110 mm outer dia(multi trap) including CP cockroach free floor grating with cup etc including cost and conveyance of all materials, labour charges, sundries etc complete as directed by the Engineer-in-Charge at all levels

od229490/2024_2025 : Providing and fixing hardwares for Handicaped door(Excluding door frame and panel).The shutter to be provided with cylindrical knob lock with rose diameter 75 mm and SS matt finished kick plate of dimension 300 MM X 1050 MM X 1MM including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing etc. complete as directed by the Engineer-in-Charge at all levels:

od229491/2024_2025 : Supply ; installation of urinal with push type auto close Stop Cock of approved make : Urinal of size 280 x 335 x 465mm with standard flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

od229665/2024_2025 : Supply ; Installation of Elbow operated Bib Cock of approved make

od229969/2024_2025 : Providing ; fixing of Manually Operated No fuel type Incinerator of capacity 20-30 KG/Hour (200-300 /KG/Day) No Fuel Type General Waste Management Equipment with size of equipment chamber: 32 Inch DIA ;60 Inch Height. Size of burning Chamber: Inner Size of the burning chamber of the equipment is 24 Inch DIA ; 34 Inch height ( volume:252 liter) , Size of ash collecting chamber Inner size of the ash collecting chamber of the equipment is 30 Inch DIA ; 10 Inch HEIGHT. Outer lining: The outer lining of the waste management equipment is made with 2.5 mm thick MILD STEEL SHEET. Inner lining: The inner lining of the waste management equipment is made with IS 8 Grade fire bricks of 4 inch thickness. This equipment is made with high quality graded materials, for the construction, high temperature FIRE BRICKS of grade IS 8 with 4 Inch thickness, Thermo Crete super calderys, Fire clay of Grade IS 8, M S Bar Grates of thickness &frac12; Inch, Top Plate of thickness of 6mm, MS SHEET of thickness 2.5 mm, Stainless steel (SS) pipe as its chimney, MS Angle, MS Flats etc complete including required foundation for fixing the equipment.

od229970/2024_2025 : Design, Supply, Installation, Testing and Commissioning of 200 KLD Sewage Treatment Plant Based on MBR Technology including all the mechanical and electrical equipments like approved pumps, MBR membranes, filters, dosing system , oil separation and skimming of kitchen waste water, Disinfection of lab effluent/ biomedical liquid effluent, 2mm fine screen for Membrane protection from sharp objects, Intermittent Air mixing system in Anoxic tank, VFD for permeate pumps, Sludge Dewatering Filter Press, Analog Instruments like- Ultrasonic level transmitter, Oxygen sesors and transmitter, Turbidity meter and transmitter, Temperature transmitter, blower and recirculation pump etc.complete for the full function of Sewage Treatment Plant. The civil foundations and RCC tank structures / pump rooms shall not be included in this item and shall be paid separately. Design of the MBR system shall be done as per site conditions and got approval from the Engineer in charge before procurement. Work shall be done as per Kerala PCB norms, manufacturer recommendation, technical specification and as directed by engineer in charge -200 KLD STP

od230289/2024_2025 : Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 160 mm dia 6 Kgf/cm2 - External work- Exposed on wall

od230369/2024_2025 : Supplying,Installing, testing and commissioning approved make Raw water Pressure sand filter with necessary accessories complete with Frontal piping,valves,suitable supports for mounting pressure guages,orifice plates.The filter shall be made of MS vessel with necessary protective coating.The cost of filter shall also include initial charge of underbed ; multi-grade filter media to suit the requirement etc.,complete as per the standards. Max. working pressure = 3.5kg/sqcm. Max flow rate = 11.5 cum/hr,at 10 hrs cycle

od230370/2024_2025 : Supplying, installing, testing and commissioning approved make Water Softener with necessary Accessories complete with Frontal piping,valves,suitable supports for mounting pressure gauges, orifice plates.The softener shall be made of MS vessel with necessary protective coating.The cost of Softener shall also include initial charge of Resin media to suit the requirement etc.,complete as per standards. Max. working pressure = 3.5kg/sqcm. Max flow rate = 11.5 cum/hr,at 10 hrs cycle

od230371/2024_2025 : Supplying, installing, testing and commissioning approved make activated carbon filter in MS vessel construction with internals, electrical control system complete with Frontal piping, valves, suitable supports for mounting, pressure guage, orifice plate etc.., complete as per the detailed specification for the efficient working of system. The maximum working Pressure shall be 3.5 Kg/Sqcm. Max flow rate = 11.5 cum/hr,at 10 hrs cycle

od230373/2024_2025 : Supplying, installing, testing and commissioning inter unit .SH 80 piping with necessary flanges, bolts, nuts, neoprene gaskets, welding wherever necessary, with necessary control valves, non return valves etc and with one coat of primer and two coats of approved enamel paint with IS reccomended colour etc., complete.

od230374/2024_2025 : Supplying, fixing, testing and commissioning pump set (horizontal or vertical type) of adequate HP capable of giving a required discharge at suitable head to work on 3Ph. 50Hz, 400/440 V with necessary unions, flanges, foundation bolts, etc., complete.Make: Grundfos/ Lubi/ Shakti Approved Equivalent ) 2) 1.0 Lps at 40 M head. 1 no. working + 1 no standby Flushing Water Distribution

od230732/2024_2025 : Boring, providing and installation bored cast-in-situ reinforced cementconcrete piles of garde M-25 of specified diameter and length belowpile cap, to carry a safe working load not less than specified, excludingthe cost of steel reinforcement but including the cost of boring withbentonite solution, chipping and removal pile casted above cutoff level, socketing in hard starta and temporary casing of appropriate length forsetting out and removal of same and the length of the pile to beembedded in the pile cap etc. by Crawler mounted, telescopic boomhydraulic pilling Rig all complete, including removal of excavatedearth with all its lifts and leads (length of pile for payment shall bemeasured up to bottom of pile cap).Note: Truck Mounted rotary/TMR/Tube well boring machine shall notbe used. 800 mm dia piles

20.2A.1 : Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-25 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution, chipping and removal pile casted above cutoff level, socketing in hard starta and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be used.600 mm dia piles

Carriage of earth By Mechanical Transport including all charges upto 21 Km as per the direction of Engineer in Charge and technical specification. Works include all labour,machinery,transportation, unloading and allied costs.

od24016/2025_2026: Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge.Single pile above above 150 tonne and upto 200 tonne capacity - Routine test

20.6.2.1 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge.Single pile above 50 tonne and upto 100 tonne capacity-Initial test

20.6.2.2 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge.Single pile above 50 tonne and upto 100 tonne capacity-Routine test

od23914/2025_2026 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification &amp; the direction of engineer -in-Charge. Single pile above 150 tonne and upto 200 tonne capacity -Initial test

od231509/2024_2025 : Providing and fixing CP brass towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality, 600 mm long towel rail of approved make

od231512/2024_2025 : Providing and fixing sanitary fixtures for handicapped toilet including one wash basin , one number pillarcock with aerator ; all other related fittings like CP brass bottle trap,CP brass angle valve, CP brasswaste coupling, etc, one number EWC ; Cistern complete with fittings ; seat cover, one no. hinged rail ;4 nos. of grab rails 60cm etc, designed for people with special needs comes with as per manufacturersspecification including cutting and making good the walls and floors wherever required as directed byEngineer-in-Charge.

od232201/2024_2025 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot ; cold water supply, including all CPVC plain ; brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes ; fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall - 65 mm nominal outer dia pipes

od232326/2024_2025 : Supply, installation, testing and commissioning of 5000 litres capacity Solar water heater with panels including cost and conveyence of all materials and labour etc complete.

od234622/2024_2025 : PUDDLE FLANGE: Supply, installation, testing ; commissioning of uPVC puddle flanges in the water tanks with necessary fittings in accordance with the drawingsand relevant standerds - 50 mm dia

od234623/2024_2025 : Supply, installation, testing ; commissioning of uPVC puddle flanges in the water tanks with necessary fittings in accordance with the drawingsand relevant standerds - 65 mm dia

od234624/2024_2025 : Supply, installation, testing ; commissioning of uPVC puddle flanges in the water tanks with necessary fittings in accordance with the drawingsand relevant standerds - 100 mm dia

od234660/2024_2025 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -160mm dia end cap

od234661/2024_2025 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 160x160x160mm dia door tee

od234662/2024_2025 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 160mm dia 45 degree Elbow

od234663/2024_2025 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 160 mm dia Elbow

od234672/2024_2025 : Supply, Installation, Testing and Commissioning CI Butterfly Valves (PN 16) Slim seal standard lever operated type confirming to BS;5155 with SS shaft, disc flange ,nuts, bolts etc complete - 80mm dia

od234673/2024_2025 : Supply, Installation, Testing and Commissioning CI Butterfly Valves (PN 16) Slim seal standard lever operated type confirming to BS;5155 with SS shaft, disc flange ,nuts, bolts etc complete -65mm dia

od234674/2024_2025 : DOUBLE STATION KNEE-OPERATED SURGICAL SCRUB SINK WITH SOAP DISPENSER: Stainless steel double station scrub sink, knee-operated, made of 1.2/1.6 mm thick SS 304 material with No. 4 finish. Features include two knee-operated water spouts, compatibility for two soap/Betadine solution dispensers with knee operation, and hot ; cold mixing valves for temperature adjustment. Wall-mounted design. Dimensions: L1700 x W690 x H1050 mm etc complete.

od234692/2024_2025 : Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling ; testing of joints complete as per direction of Engineer in Charge. 160 mm dia 6 Kgf/cm2

od235709/2024_2025 : Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 50 mm nominal bore

od235710/2024_2025 : Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:40 mm nominal bore

od235711/2024_2025 : Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 32 mm nominal bore

od235712/2024_2025 : Providing and fixing CPVC Y- Strainer of 65mm diameter in the pipe line of approved quality having corrosion resistance, high-performance filtration, and easy maintenance

od235713/2024_2025 : Supply and installation of Kirloskar make Three phase borewell submersible pump model KU4-0328T, 28 no.of stages, 1.50KW/2HP, Del 32 mm , suitable for 40 mtr to 176 mtr head and 40 LPM to 176LPM discharge respectively,Including Emrgency push button (IP 65) and Cost ; conveyence off all materials etc complete.

od237020/2024_2025 : Providing and laying of Filter media with granular materials/stone crushed aggregates satisfying the requirements specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the height mentioned compacted to a firm condition complete as per drawing and direction of engineer in charge.

od237021/2024_2025 : Supplying laying and jointing in filter media trenches factory made perforated HDPE subsoil drainage pipe, wrapped with 150 GSM Geotextile for subsoil drainage system including all necessary coupling/ fittings/labours for laying at required slope as per specifications etc complete (Filter media to be measured and paid seperatly) . The Pipes for subsoil drainage shall have an external diameter of 110 mm manufactured from High Density Polyethylene (HDPE) of class PE 80. The pipe must possess a minimum of 66% perforation across its surface area. The product should satisfy the following parameters 1. Ring Stiffness as per ISO 9969: 2016 should be &gt; 0.8 KN/SqM 2. Resistance to Acid with 3% HCl for 24 hrs without mass loss, change in colour, softening, cracking or spalling. 3. Resistance to Alkali with 3% KOH for 24 hrs without mass loss, change in colour, softening, cracking or spalling. The rate is inclusive of cost of all materials, labour charges, lead, lift etc complete. The work shall be done as per the direction of Engineer In Charge.

od237053/2024_2025 : Supplying, cutting and fixing of 6mm Exterior Grade HPL sheet of approved make to the steel frame work of Gate with riveting ; bolted with washers etc complete. including cost and conveyance of all materials, scaffolding cahrges and labour charges etc complete as per the direction of Engineer In charge.

od237153/2024_2025 : Supply, Installation, Testing ; Commissioning of Electric Water Heaters (Geysers) of capacity 3 liters of approved make including stop cock etc complete as per the direction of Engineer in Charge.

od237786/2024_2025 : Providing and fixing Rubber Speed Humps with the following specification:i)Weight 15kg/Unit, ii) Size 500x350x50 mm Material High strength designed rubber, iii) Color black and Yellow combination, iv) bearing Capacity 20 - 25 Tons. V) having UV Resistance vi) Usage/Application : Thar/Cement/Concrete Surface. etc complete including fixtures all lablour, material and transportation charges complete as per the direction of Engineer in Charge.

od237838/2024_2025 : Providing and fixing PVC WEEP HOLES-using 75mm dia- 4kg /sq.cm including cost of materials, conveyance, labour charges etc. complete

od238202/2024_2025 : Supplying, Installing, testing and commissioning water pump Mono block two numbers pump (1W+1S) with motor and IP - 67 enclosure, of adequate HP, capable of giving a required discharge at suitable head to work on 3Ph 50Hz, 400/440Vsupply with necessary unions, flanges, bellows, Auto level controllers starters, switchgears, timers, contactors overload relay push buttons, LED indicators, provision for changing working and standby, etc. complete as per the direction of Engineer In Charge. 5 Lps at 20M head (1 no. working + 1 no. standby = 1 Set)

od238203/2024_2025 : Supplying, Installing, testing and commissioning water pump submersible two numbers pump (1W+1S) with motor and IP - 68 enclosure, of adequate HP, capable of giving a required discharge at suitable head to work on 3Ph 50Hz, 400/440Vsupply with necessary unions, flanges, bellows, Auto level controllers , starters, switchgears, timers, contactors overload relay push buttons, LED indicators, provision for changing working and standby, etc. complete as per the direction of Engineer I charge. 1 Lps at 10M head- Single phase portable pump.

od238204/2024_2025 : Supplying, Installing, testing and commissioning water pump submersible two numbers pump (1W+1S) with motor and IP - 68 enclosure, of adequate HP, capable of giving a required discharge at suitable head to work on 3Ph 50Hz, 400/440Vsupply with necessary unions, flanges, bellows, Auto level controllers , starters, switchgears, timers, contactors overload relay push buttons, LED indicators, provision for changing working and standby, etc. complete as per the direction of Engineer I charge. 2 Lps at 10M head. (1 no. working + 1 no. standby = 1 Set)

od238205/2024_2025 : Supplying, Installing, testing and commissioning water pump submersible two numbers pump (1W+1S) with motor and IP - 68 enclosure, of adequate HP, capable of giving a required discharge at suitable head to work on 3Ph 50Hz, 400/440Vsupply with necessary unions, flanges, bellows, Auto level controllers, starters, switchgears, timers, contactors overload relay push buttons, LED indicators, provision for changing working and standby, etc., complete as per the direction of Engineer In Charge - 5 Lps at 60M head

od238206/2024_2025 : Supplying, Installing, testing and commissioning water pump submersible two numbers pump (1W+1S) with motor and IP - 68 enclosure, of adequate HP, capable of giving a required discharge at suitable head to work on 3Ph 50Hz, 400/440Vsupply with necessary unions, flanges, bellows, Auto level controllers , starters, switchgears, timers, contactors overload relay push buttons, LED indicators, provision for changing working and standby, etc. complete as per the directionof Engineer I charge. 2 Lps at 70M head. (1 no. working + 1 no. standby = 1 Set)

od238207/2024_2025 : Supplying, Installing, testing and commissioning water pump submersible two numbers pump (1W+1S) with motor and IP - 68 enclosure, of adequate HP, capable of giving a required discharge at suitable head to work on 3Ph 50Hz, 400/440Vsupply with necessary unions, flanges, bellows, Auto level controllers , starters, switchgears, timers, contactors overload relay push buttons, LED indicators, provision for changing working and standby, etc. complete as per the directionof Engineer I charge. 10 Lps at 60M head. (1 no. working + 1 no. standby = 1 Set)

od238961/2024_2025 : Construction of valve chamber with 230 mm best quality TM bricks in CM 1:4 over a bed of 100mm thick PCC 1:4:8, internal walls plastered smooth in CM 1:3 and external walls plastered rough with sponge finish including curing with all necessary leads and lift and providing heavy duty cast iron cover with frame with locking arrangements etc., complete including Heavy duty cast iron cover of size 600 x600 (weight 115Kgs.) Size of chambers for valves up to 150 mm dia Size 0.6m x 0.6m x 1M (clear dimension) including approved make cast brass body water meter with necessary unions for fixing on the inlet main as shown on the drawing, etc., complete with (of approved makes - analog type). 100mm nominal dia

od238992/2024_2025 : Supplying, Installing, testing and commissioning water pump Mono block two numbers pump (1W+1S) with motor and IP - 67 enclosure, of adequate HP, capable of giving a required discharge at suitable head to work on 3Ph 50Hz, 400/440Vsupply with necessary unions, flanges, bellows, Auto level controllers starters, switchgears, timers, contactors overload relay push buttons, LED indicators, provision for changing working and standby, etc. complete as per the direction of Engineer In Charge. 5 Lps at 35M head (1 no. working + 1 no. standby = 1 Set)

od239229/2024_2025 : Supply and stacking of well developed with fresh and healthy bushy plastic plotted plant Pentanus in full bloom of height 30-45cm in a developed flowering bed as per direction of the Engineer-in-charge

od239230/2024_2025 : Supply and stacking of well developed with fresh and healthy bushy plastic plotted plant fycus panda in full bloom of height 30-45cm in a developed flowering bed as per direction of the Engineer-in-charge

od239231/2024_2025 : Supply and stacking of well developed with fresh and healthy bushy plastic plotted plant heliconia sen vincent in full bloom of height 45-60cm in a developed flowering bed as per direction of the Engineer-in-charge

od239232/2024_2025 : Supply and stacking of well developed with fresh and healthy bushy plastic potted plant Spider lilly in full bloom of height 45-60cm in a developed flowering bed as per direction of the Engineer-in-charge

od239267/2024_2025 : Water purifier: Supplying, Installing, testing and commissioning approved make Raw water Pressure sand filter with necessary accessories complete with Frontal piping, valves, suitable supports for mounting pressure gauges, orifice plates. The filter shall be made of MS vessel with necessary protective coating. The cost of filter shall also include initial charge of under bed multi-grade filter media to suit the requirement etc., complete as per the standards. Max. working pressure = 10kg/sqcm. Max flow rate = 6m3/hr/m2 800 dia filter at 10 hrs cycle etc complete as per the Direction of Engineer In Charge

od239873/2024_2025 : Supplying and fixing CI manhole cover of size 600x600mm heavy duty (110kg) of approved make as per the directions of Engineer in charge

od239876/2024_2025 : Supplying, Installing ; Testing at site in position CPVC Sch-80 of approved make for Pump room water supply, complete with all necessary Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. &quot;U&quot; bolts (8 mm thick) on G.I. slotted rails (1.6 mmthick) , Rail legs (2.5 mm thick) of approved make, as perdrawings to the satisfaction of the Project Manager.(For Pump room Piping) 75 mm nominal inner dia Pipes

od239877/2024_2025 : Supplying, Installing ; Testing at site in position CPVC Sch-80 of approved make for Pump room water supply, complete with all necessary Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. &quot;U&quot; bolts (8 mm thick) on G.I. slotted rails (1.6 mmthick) , Rail legs (2.5 mm thick) of approved make, as perdrawings to the satisfaction of the Project Manager.(For Pump room Piping) 100 mm nominal inner dia Pipes

od240661/2024_2025 : Construction of embankment using available earth with all lifts and leads, spreading, grading to required slope and compacting to meet requirement of table 300-2 including required machineries as per the direction of Engineer in Charge.

od246436/2024_2025 : Providing and fixing Name board in Building using Gl metal frame with Aluminium composite panel and block letters of required size (malayalam/English) with Titanium gold 2inch projection and LED outer glow for letters including cost and conveyanceof all materials , scaffolding ; labour charges etc complete as per the direction of Engineer in charge. - Fixing on main gate with ACP base Panel of size 1353.82cm x 66cm and English letter TALUK HOSPITAL, KOTTARAKKARA with Titanium gold. Malayalam letter THAALOOK AASUPATHRI, KOTTARAKKARA of upper height 50.80cm and lower height 30cm. Total letter width of english and malayalam are 551.18cm each. Height of each letter is 30cm.

od246437/2024_2025 : Providing and fixing Name board in Building using Gl metal frame with Aluminium composite panel and block letters of required size (malayalam/English) with Titanium gold 2inch projection and LED outer glow for letters including cost and conveyanceof all materials , scaffolding ; labour charges etc complete as per the direction of Engineer in charge. - Fixing on wall with ACP Panel of size 685cmx153cm and malayalam letter-THAALUK AASUPATHRI KOTTARAKKARA in malayalamof total letter width 648cm and upper and lower height letter of 84cm and 50.8cm respectively with total letter width of 252.4cm respectively.

od246439/2024_2025 : Grading roof for water proofing treatment at all floor level (upto eighth floor level ) with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

od246440/2024_2025 : Providing and laying Antiskid Ceramic floor tiles 300x300x7 mm of Ist quality conforming to IS : 15622 of approved make,shade,and pattern laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc.including cost and conveyance of all materials,labour charges,lead,lift etc, complete as directed by the Engineer-in-Charge at all levels.

od246442/2024_2025 : Providing, fixing, supply and installation of seamless Conductive tile flooring(imported-GERFLOOR(Germany) system,2mm thick with perfectly curved flush covings, all joints welded properly (6&quot; skirting also considered in epoxy floor measurement). the installed floor shall be of stain proof, seamless, uniform color and free of joints / undulations/ bubbles etc)

od246443/2024_2025 : WALL VINYL : Providing and Fixing 1mm thick Homogeneous Wall Vinyl covering with polyurethane protective surface having antifungal and anti bacterial properties in accordance with ISO 22196, of approved color and complying to color fastness as per ISO 105-B02, size and texture to the proper level, line using adhesive as per manufacturer specification, joint treatment, welding etc complete as directed by the Engineer -in-Charge at all levels. The joints shall be welded properly with the same color welding cord.

od246444/2024_2025 : VINYL FLOORING: Providing and Fixing of 2mm thick Polyurethane reinforced laminated antistatic, antifungal, antibacterial Vinyl Flooring sheet and skirting, including self leveling upto 3mm thick with cementitious material, flexibility less than 20mm, residual indentation less than 0.1mm electrical behavior less than 2kV, of approved color, size and texture over the floor surface to proper level, line using adhesives as per manufacturer specification including copper strips and connectivity to obtain antistatic property as above, joint treatment, coving cum capping, welding etc complete as directed by the Engineer-in-Charge at all levels. The joints shall be welded properly with the same color welding cord.

od246445/2024_2025 : Supply and fixing of Corner Patch lock of approved Make for glass doors as per the direction of Engineer in Charge.

od246446/2024_2025 : Supply and fixing of back to back pull handle dia 25mm, CTC length 400, SS finish O/A 50 of Hettich Make for glass doors as per the direction of Engineer In charge

od246449/2024_2025 : Supply and installation of Ceiling/corner paneling system: 0.8 mm thick 304 graded Stainless sandwich panel with core consisting of rigid polyurethane foam which has been injected under hipressure with a minimum density of 40 kg/m3. Total insulated panel thickness with stainless steel sheet should be 30 - 40 mm.The gap between panel should be filled with filler material and finished to fine grade surface and finished with anti fungal medical grade paint. Suspension/fixation system (brackets and threaded rods) as per manufacturer recommendation shall be used. Sub structure materials should be galvanized steel as per standards. All necessary fittings should be integrated with panels. Rate shall be all inclusive of labour, materials etc.

od246450/2024_2025 : Providing and fixing Stainless Steel- D- type handle - 450mm height of approved make for glass doors with necessary accessories and screws etc. complete

od246451/2024_2025 : Providing and fixing Lead Shielding Door shutter and frame: of (2 Hrs Fire Rated)Door frame shall be double rebate profile of size 143 x 58 mm made out of 1.6 mm (16 gauge) thick galvanized steel sheet. Frames shall be butted and field assembled with bolts. The inside face of the frame face trim to rebate height should be protected with 2.0 mm thick lead line. All provision should be mortised, drilled and tapped for receiving appropriate hardware. Rubber door silencers should be provided on the strike jamb. Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening. Frame should be Rockwool infill.Door leaf shall be minimum 46 mm thick fully flush double skin door. Door leaf shall be manufactured from 1.2 mm (18 gauge) thick galvanized steel sheet. The internal construction of the door should be rigid with lead line of 1.6 mm thick all across the inside of the exposed surface. In addition, the door should have steel channel reinforcement with a basic infill of honeycomb core. All doors should be factory prepped for receiving appropriate heavy duty hardware and provided with necessary reinforcement for hinges, locks, and door closers as per ANSI Standard

od246452/2024_2025 : Providing, assembling and supplying toughened glass of 8mm thickness vision panel units of size and shape as required and specified, of approved colour and shade with spacer tube 12mm wide, desiccants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. (Payment for fixing of glass Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.(i) Coloured tinted performance glass of 8mm thick of approved make having properties as visible Light transmittance (VLT) of 25 to 65 %, Light reflection internal 10 to 20%, light reflection external 10 to 20 %, shading coefficient (0.25-0.28) and U value of 3.0 to 6 W/m2 degree K etc complete.

od246453/2024_2025 : Supply and fixing SS 304Grade angle of size 50x50x1mm thick as corner guard for wall tiles

od246457/2024_2025 : supplying and fixing baker rods and fill polymer mortar to get an even surface. Over that surface pollysulphide sealant (SIKA make) applied, finished smooth etc complete including surface preparation, labour, SBR; baker rod, scaffolding etc complete as per manufactures specifications and direction of Engineer In charge.

od246461/2024_2025 : Providing and fixing powder coated Aluminium louvered Ventilators (minimum thickness of powder coating 50 microns) of approved colour and approved make, with 5mm thick frosted glass of approved make for aluminium U channel louvers including necessary grooves in frames for fixing glass etc. complete

od246463/2024_2025 : Providing and fixing stainless steel TGD handles 32x600 mm as per drawings and specifications and as per direction of Engineer-in-Charge.

od246464/2024_2025 : Providing and fixing 100 mm size patch lock ( best make of approved quality ) with Euro cylinder for glazed doors including necessary cutting and making good etc. complete

od246465/2024_2025 : OT DOOR ( AUTOMATIC)Track : High grade aluminum extrusion profile to carry any door weight (till size 3000mm X 2400mm) with deep indentations to ensure perfect hermetic sealing Canopy : For HPCL Door:- Powder coated galvanized sheet over the full length of track with sloping top and closing caps.Door Blade : Door core of 60mm thick built up with:- Door Profile : Door core is surrounded by 2.5 mm thick high grade aluminum extrusion profiles with natural anodizing of 15 microns finish. The aero-dynamic design of profiles makes the door ROBUST in its segment league. Gaskets : Door blade is made with 3-tier specially designed 3 side heavy duty replaceable EPDM gasket against wall frame. Bottom sealing with 2-tier heavy duty EPDM gasket to flush with finished floor.Opener : Stainless Steel INDEMAND lever handle on both side of the door blade for smooth and easy door opening and closing OR for small door outside D-grip handle and inside flush grip. Wall Frame : High grade Aluminum extrusion with natural anodized 15 micron finish wall frame profile. This wall frame profile is 3-sided blind fixed with cladding on wall cut-out section from inside and outside of the room. Cladding : The cut-out of wall section is covered with 1mm thick high pressure laminate glued on 9mm high density particle board.Acoustic : Sound reducing door up to 28db.Operation : Door can be open/close manually or with automation.Weight : Complete door blade weight is 125 Kg approx and track assembly is 20 Kg. Sliding : Door can be open to Right Hand Slide OR Left Hand Slide.Suitable For : Operation Theaters, Intensive Care Units (ICU), Laboratories, Sterile Rooms,Pediatric Wards, Quarantine Areas and Lobbies etc.&quot; Supply and installation of Ceiling/corner paneling system: 0.8 mm thick 304 graded Stainless sandwich panel with core consisting of rigid polyurethine foam which has been injected under hipressure with a minimum density of 40 kg/m3. Total insulated panel thickness with stainless steel sheet should be 30 - 40 mm.The gap between panel should be filled with filler material and finished to fine grade surface and finished with anti fungal medical grade paint. Suspension/fixation system (brackets and threaded rods) as per manufacturer recommendation shall be used. Sub structure materials should be galvanised steel as per standards. All necessary fittings should be integrated with panels. Rate shall be all inclusive of labour, materials etc.

od246466/2024_2025 : OT Entry Door (HSS-Automatic) - Providing , Fixing and commissioning of CE marked Automatic Electronically Operated Hermetically Sealing Sliding Doors (1800mm wide x 2200mm height) complying to international standards, Each Unit contains below mentioned:Make : Rebbon / Metaflex i) Hermetically sealing sliding door (1800 x2200mm) ii) Electronic Automation Unit for Door iii) Two Magic Switches iv) Two Elbow Switches v) One Photocell vi) Viewing Window (300 mm x 300 mm) vii) Stainless steel / Al. door handlesviii) Seal Frames including labour, material, transportation etc complete all as per manufactures specification and direction of Engineer in Charge.

od246467/2024_2025 : Providing and fixing 30mm Lead Lined SS Sandwich Panel Lined With 2 Mm Thick Lead Size:1200 mm X1200mm for chest examination in X ray room (LEAD sheet Size 1.20x 1.20m) with necessary screws, including all cost of materials and labour charges etc. complete. all as per direction of Engineer In charge

od246468/2024_2025 : Supply ; Installation of 150mm wide wall guard having vinyl snap-on-cover(lead free). Aluminium retainer cover shall be 2mm thickness and retainer fabricated from 6063-TS Aluminium. The system shall resist an impact of 45.5ft-lbs as per ASTM-F-476-84 Fire rating, chemical and stain resistance etc complete all as per the direction of Engineer In Charge

od246469/2024_2025 : Supplying and fixing powder coated 20mm size Aluminium channel 2.5mm thickness hanging support of required length one end fixing from slab by using 6mm dia expansion bolt at a distance of not more than 2m, c/c down end fixed to powder coated aluminium channel frame 27 x 20mm x 1.5 mm thick section with pvc runner by using SS screw as per the direction of engineer in charge including labour, material and conveyance etc complete.

od247839/2024_2025 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x10x20 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to terrace floor level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of labour, scaffolding work etc. complete

od247841/2024_2025 : providing 3 No of 3mmx3mm grooves in granite threads as per architectural drawing, including cost of labour, machinery and making the surface clean as per the direction of engineer in charge.

od247842/2024_2025 : Providing and fixing Powder coated Aluminium (minimum thickness of powder coating 50 micrones) locking arrangement for sliding windows including necessary screws and fittings of approved make as directed by the engineer in charge

od247844/2024_2025 : Supplying, fabricating and fixing 4mm ACP duct door with approved aluminium sections as frames, including all fittings (2nos of SS hinges of size 100mm ; alen key lock) including cost and conveyence of all materials and labour etc all complete.

od247845/2024_2025 : Wall painting with water based PU paint having antibacterial and antifungal properties of approved brand and manufacture to give an even shade including epoxy priming coat : Two or more coats on new work

od247852/2024_2025 : Provided and fixing dusted/frosted glass film of make 3M/Avery Dennison orequivalent of approved shade (overall thickness of Film + Adhesive shall be approx. 120 microns) on glasswith customized prints with HP latex based high quality prints. The film shall install with self-adhesiveand bubble-free installation to be done on clean glass .The rate shall include the cost and conveyance ofall materials, labour charges, scaffolding, lead ,lift, sundries, print, wastage ,design, operations etc completeas directed by the Engineer in charge at all levels.

od247855/2024_2025 : Providing and fixing glazing in fire resistant door shutters,Vision lite of 120min fire rating and size 200x300 mm or 150 x 400mm(max area 0.06sqm) wherever applicable should be provided with single layered clear fire rated glass panes of 5mm thickness of approved brand, as per guidelines laid down under IS 3614 : 2021 vide clause no. 7.2.7 table no. 2 with a clipon arrangement.The glass will be provided with fire rated ceramic tape of min.2 mm thickness with min.15mm width alround on either face. Every Glass pane must carry a permanent marking of its glass manufacturer (Actual glass size is to be measured at site for payments).

od247856/2024_2025 : Providing and fixing insulated fire rated GI Sheet doors conforming to FD 120-I 30 classification of IS 3614 :2021 with fire rating of 120 minutes integrity and 30 minutes insulation. The factory manufactured door frame and shutter assembly shall be made out of minimum 1.20 mm thick GI Sheet with minimum 120 GSM coating as per IS: 277. Door and frame should be finished with powder coating in standard RAL shade finish having DFT of minimum 30 microns. The door should carry a minimum 500 Hrs of salt spray test. All accressesories like hardware, vision panel, fire ; smoke seal etc to be supplied by Fire door manufacturer only as per the guidelines laid down in IS 3614:2021.Every door must carry a label confirming to type of door ; its fire rating.The door must carry a 5years valid test evidence from CBRI-Roorkee / NTH-Kolkata/ NABL accrediated lab which operates in accordance with ISO/IEC 17025. The Door frame shall be single rebate grooved profile of size minimum 100mm x 57mm made out of 1.20mm (18gauge) minimum thick galvanized steel sheet. Frames shall be butt / mitered joint and field assembeled with bolting system. Frames to have inbuilt grooved to accomodate Intumuscent fire seal strip . . The frame should also be provided with fire rated EPDM smoke seal 20x4 mm conforming to IS: 3614:2021 or as per test evidence. It shall be fixed in grooves, specifically cut in rebate on all the 3 sides of the frame.. All provisions should be mortised ; provided with necessary inbuilt reinforcement to receieve appropriate hardware. Frames should be provided with back plate bracket for anchor fastner with 8-10 mm dia and minimum 80 mm long HDG fasteners, with Polyamide sleeves for installation of frame in finished plastered masonary wall opening. Door leaf should be minimum 46mm thick fully flush double skin door. Door leaf must be manufactured from 1.2mm(18gauge) thick galvanised steel sheet. The infill material shall be mineral wool of minimum density 48 kg/cum. All doors shall be factory prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges should be interlocked with a bending radius of 1.4mm. For double leaf doors integrated astragals has to be provided on the meeting stile for both active and inactive leaf.The shutters shall be mounted to the frame with SS 304 grade ball bearing type hinges of size 100x 75x3 mm. (the rates shall be inclusive of all other accessories except Glazing, Door Closer, handle, Lock ; Panic bars )

od247858/2024_2025 : Supplying and fixing keyless baby latch of approved make including cost and conveyance of all materials and labour etc complete.

ELECTRICAL SERVICE WORKS- HT Works

od235535/2024_2025 : Supply, Installation Testing and Commissioning of 11KV electrically Operated 21kA for 3 sec, 630A SF6 Insulated, SCADA compatiable, 4 way Ring Main Unit outdoor type (CTCT)with 2nos motorized 630A TP Load Break Switch and 2 nos. motorized VCB , 630 Amp continously rated Cu busbar complete with all accessories, protective relays, indicators,battery and battery charger, Manometer for indicating SF6 gas pressure with green zone marked on the scale,provision for padlocking for open, close, earth and test position etc. on a suitable foundation. The RMU must be both side extensible type and compatible for SCADA system.The rate quoted shall be including RCC foundation, erection , earthing, necessary interconnections, conducting precommissioning tests, and all control wiring complete as per single line diagram ; technical specification.

od235536/2024_2025 : OUTDOOR METERING PANEL Supply installation testing and commissioning of 11kV, outdoor, wheatherproof,IP 65 duty metering having short time current rating of 18kA, cubicle fabricated out of 14 SWG CRCA sheet, powder coated after seven tank process, provision for connecting 3x300sqmm cable at both ends, 3nos 25/5A, Cl-0.2s, 10VA CT, 11kV/110V, Cl-0.2, 25VA PT, fixing of already tested TOD meter fixed in pilfer-proof outdoor meter box suitable for housing the meter and test terminal block (TTB), all complying with relevant standards and as per the requirements of KSEBL including excavation, backfilling providing RCC foundation for cubicle arranging testing of CT, PT unit at standard testing lab TMR of KSEBL etc complete

od235537/2024_2025 : TOD METER Supply, installation and testing of TOD meter with provision of bi-directional energy measurement and net integration for KSEB 3x110V/√3, -/5A, 0.2s, LCD display type, DLMS compatiable, Energy meter with KW,KVA, KVA, KWh, KVARh, KVAh, MD indicator as per KSEB requirement. including arranging testing of meter in the TMR section of KSEB and as per recommendations and fixing in the metering panel complete as required.

od235538/2024_2025 : UNITISED SUB STATION - INDOOR - WITH VCB PANEL - 11KV - 400KVA. Indoor Unitised Substation (USS) with the following: Incomer: 11kV,630A, 500MVA, VCB , 24V dc shunt trip coil, battery, battery charger, overcurrent and earth fault relay, protection CT, 50-25/5A, Cl 5P10 CT, 3O/C and 1EF Protection static relays with high set element, cable box suitable for 3x300sqmm 11kVcable and emergency OFF push button,etc including all accessories in complete - 1No. Transformer:400kVA, 11kV/433V, 50Hz, 3phase, Cu-wound AN cooled, Vector DYN-11, cast resin, indoor,IP 22, dry-type transformer with off-load tap changer, winding temperature alarm and trip, HV top entry type cable box, LV terminals suitable for connecting cable of 2 run 3.5x400 sqmm cable - 1No Suitable base plate for mounting of the equipment, bus bar inter connections, operating handle mechanism, spring charging mechanism and enclosure for the USS.

od235539/2024_2025 : UNITISED SUB STATION - INDOOR - WITH VCB PANEL - 11KV - 630KVA. Indoor Unitised Substation (USS) with the following: Incomer: 11kV,800A, 500MVA, VCB , 24V dc shunt trip coil, battery, battery charger, overcurrent and earth fault relay, protection CT, 50-25/5A, Cl 5P10 CT, 3O/C and 1EF Protection static relays with high set element, cable box suitable for 3x300sqmm 11kVcable and emergency OFF push button,etc including all accessories in complete - 1No. Transformer: 630kVA, 11kV/433V, 50Hz, 3phase, Cu-wound AN cooled, Vector DYN-11, cast resin, indoor,IP 22, dry-type transformer with off-load tap changer, winding temperature alarm and trip, HV top entry type cable box, LV terminals suitable for connecting cable of 4 run 3.5x400 sqmm cable - 1No Suitable base plate for mounting of the equipment, bus bar inter connections, operating handle mechanism, spring charging mechanism and enclosure for the USS.

od238506/2024_2025 : Supply, testing and commissioning of the following PVC Insulated Armoured Aluminium Cables (AYWY/AYFY) /XLPE (A2XCEFY) .3.0C x 150 SQ.MM.XLPE

8.1.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 120 sq. mm and upto 400 sq. mm

8.2.2 : Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etcAbove 120 sq. mm and upto 400 sq. mm

8.3.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 120 sq. mm and upto 400 sq. mm

od235703/2024_2025 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade offollowing size in the existing masonry open duct/cable tray as required.Above 120 sq. mm and upto 400 sq. mm

10.4.2 : Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required:120 sq. mm

10.5.2 : Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :120 sq. mm

UPS and DG SETS

od235748/2024_2025 : WARD TOWER - DG SET(500KVA): Supply Installation testing and commssioning of 3phase., 500 kVA 433V, 0.8pf. 50Hz, 1500rpm DG Prime Rated Diesel Generator Sets as detailed below and as shown on drawings. Water cooled diesel generating set comprising diesel engine, alternator, fuel tank, starting system, battery, electronic governor, etc. with all accessories as required. The generator set shall have an integral type acoustic enclosure as per latest CPCB IV norms. Smoke exhaust emission from diesel engines shall comply with the latest emission standards. Generator set shall be inclusive of flywheel, flexible direct coupling, air cleaner, fire and corrosion resistant coating applied in two coats with necessary primer, fan with guard, fuel pump, fuel filter, electrical starting system with starter, 24V battery with 240/24V charger, instrument panel, RPM indicator, residential silencer, etc. The control panel shall be floor mounted dust and vermin proof with suitably rated, 800 A,4Pole, 50kA, ACB complete with all necessary relays, CTs, control wiring,low set earth fault relay with CT, 3x240V, cl 0.5s Energy meter etc. Scope shall include first filling of oil up to 500 Litres of 990 litre capacity diesel tank for commissioning of the DG set.

od235749/2024_2025 : DIAGNOSTIC BLOCK - DG SET(320KVA): Supply Installation testing and commssioning of 3phase., 320 kVA 433V, 0.8pf. 50Hz, 1500rpm DG Prime Rated Diesel Generator Sets as detailed below and as shown on drawings. Water cooled diesel generating set comprising diesel engine, alternator, fuel tank, starting system, battery, electronic governor, etc. with all accessories as required. The generator set shall have an integral type acoustic enclosure as per latest CPCB IV norms. Smoke exhaust emission from diesel engines shall comply with the latest emission standards. Generator set shall be inclusive of flywheel, flexible direct coupling, air cleaner, fire and corrosion resistant coating applied in two coats with necessary primer, fan with guard, fuel pump, fuel filter, electrical starting system with starter, 24V battery with 240/24V charger, instrument panel, RPM indicator, residential silencer, etc. The control panel shall be floor mounted dust and vermin proof with suitably rated, 630 A,4Pole, 50kA, MCCB complete with all necessary relays, CTs, control wiring,low set earth fault relay with CT, 3x240V, cl 0.5s Energy meter etc. Scope shall include first filling of oil up to 500 Litres of 990 litre capacity diesel tank for commissioning of the DG set.

od235750/2024_2025 : Providing, fixing of exhaust pipe line of 200/150mm dia B class MS pipe suitable for Exhaust line of DG set with accessories like flange, supports, through wall including painting etc complete

od235751/2024_2025 : Providing, fixing of exhaust pipe line of 200/150mm dia B class MS pipe suitable for Exhaust line of DG set with accessories like flange, supports, through wall, including providing thermal insulation heat resistance painting etc, complete

od235752/2024_2025 : 40 KVA UPS WITH BATTERY BANK SITC of a Three-Phase Input/Output IGBT-based parallel redundant (2x20 KVA) 40 KVA UPS system with a minimum of 30 minutes backup. The Three-Phase input voltage shall be 4-wire, 415V, variable between +20% to -20%, 50Hz &plusmn; 6%. The UPS system shall deliver clean, ripple-free pure sine wave output both in the presence and absence of mains supply. The current and voltage harmonic distortions generated by the UPS system shall be within acceptable limits as per international and national standards, with ripple (without battery) less than 1%, and THD less than 2% for 100% linear load and less than 5% for 100% non-linear load. The UPS system shall be a double conversion, microprocessor-based, true online system with individual battery banks, each with its own cooling arrangements. It shall include an LCD display, three-phase input and output, with PWM IGBT-based DSP control, and provide 20 minutes of external SMF battery backup with auto-bypass functionality. The output voltage range shall be 415V &plusmn; 0.5%, with a frequency range of 50Hz &plusmn; 0.05%, a minimum output power factor of 0.9, THD of less than 2% for linear loads, and less than 5% for non-linear loads. Additionally, the output side shall include a 415/415V 3-phase 50Hz 40 KVA isolation transformer, with all necessary interconnections. The system shall have a crest factor of 3:1, efficiency greater than 95%, and overload capacity of 110% for 5 minutes and 150% for 30 seconds. The rate shall include connecting copper cabling and earthing between nearby UPS modules and from the UPS to the output isolator, with all required accessories.

od235753/2024_2025 : 60 KVA UPS WITH BATTERY BANK SITC of a Three-Phase Input/Output IGBT-based parallel redundant (2x30 KVA) 60 KVA UPS system with a minimum of 30 minutes backup. The Three-Phase input voltage shall be 4-wire, 415V, variable between +20% to -20%, 50Hz &plusmn; 6%. The UPS system shall deliver clean, ripple-free pure sine wave output both in the presence and absence of mains supply. The current and voltage harmonic distortions generated by the UPS system shall be within acceptable limits as per international and national standards, with ripple (without battery) less than 1%, and THD less than 2% for 100% linear load and less than 5% for 100% non-linear load. The UPS system shall be a double conversion, microprocessor-based, true online system with individual battery banks, each with its own cooling arrangements. It shall include an LCD display, three-phase input and output, with PWM IGBT-based DSP control, and provide 20 minutes of external SMF battery backup with auto-bypass functionality. The output voltage range shall be 415V &plusmn; 0.5%, with a frequency range of 50Hz &plusmn; 0.05%, a minimum output power factor of 0.9, THD of less than 2% for linear loads, and less than 5% for non-linear loads. Additionally, the output side shall include a 415/415V 3-phase 50Hz 60 KVA isolation transformer, with all necessary interconnections. The system shall have a crest factor of 3:1, efficiency greater than 95%, and overload capacity of 110% for 5 minutes and 150% for 30 seconds. The rate shall include connecting copper cabling and earthing between nearby UPS modules and from the UPS to the output isolator, with all required accessories.

LT PANELS

od235644/2024_2025 :MAIN SWITCH BOARD 1 - Ward Tower (MSB W ): Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, panel board with AMF logic (load bearing) fabricated using CRCA 16/14 SWG powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process. The panel shall be complete with all necessary switch gear, control gear, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. as required and as listed below in brief and details in technical specifications.All necessary components, rotary handle, spreader, neoprene gasket, door locking arrangements, suitable earth bus including all accessories. Incomer: 1. 1000A, 35kA, 4P, EDO, ACB - 1Nos. 2. 800A, 35kA, 4P, EDO, ACB - 1Nos Bus Bar: Al busbar sized suitably for 1000A TPN and 25x6 Cu Earth Outgoing: 400A, 35kA, TP + NL-MCCB- 1No.320A, 35kA, TP MCCB + NL- 1No, 250A, 35kA, TP + NL ISOLATOR- 1No, 250A, 35kA, TP + NL MCCB - 4Nos, 200A, 35kA, TP + NL MCCB - 1No, 160A, 35kA, TP + NL MCCB - 2Nos Metering, indication and protection relays, Auto start and auto load sharing with AMF Logic 1No, Control Wiring - 1Lot, Electrical and Mechanical Interlocking arrangement - 1Set, Surge Protector - 1No, Master Relay - 1No, Multi Data Meter 3ph. 4 wire type with serial port. Low set earth fault relay with 1000/5A, 5P10 ,15VA CT and 600/5A, 5P10, 15VA CT R Y B ; ON/ OFF indication lamp for incomers with MCB, All the incoming and outgoing feeders shall be fitted with Maximum demand indicators with RS 485 communication port.

od235645/2024_2025 :MAIN SWITCH BOARD 2 - Dignostic Block (MSB D ): Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, panel board with AMF logic (load bearing) fabricated using CRCA 16/14 SWG wpowder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process. The panel shall be complete with all necessary switch gear, control gear, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. as required and as listed below in brief and details in technical specifications.All necessary components, rotary handle, spreader, neoprene gasket, door locking arrangements, suitable earth bus including all accessories. Incomer: 630A, 35kA, 4P, Microprocessor based MCCB and 630A 4 pole contactor - 2sets. Bus Bar: Al busbar sized suitably for 630A TPN and 25x6 Cu Earth Outgoing:250A, 35kA, TP + NL MCCB - 3Nos, 200A, 35kA, TP + NL MCCB - 4Nos, 160A, 35kA, TP + NL MCCB - 2Nos,125A, 35kA, TP + NL MCCB - 1No Metering, indication and protection relays, Auto start and auto load sharing with AMF Logic 1No, Control Wiring - 1Lot, Electrical and Mechanical Interlocking arrangement - 1Set, Surge Protector - 1No, Master Relay - 1No, Multi Data Meter 3ph. 4 wire type with serial port. Low set earth fault relay with 600/5A, 5P10 ,15VA CT, R Y B ; ON/ OFF indication lamp for incomers with MCB, All the incoming and outgoing feeders shall be fitted with Maximum demand indicators with RS 485 communication port.

od235646/2024_2025 :DIAGNOSTIC BLOCK - UTILITY PANEL Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, LT panel board fabricated using 16/14 SWG CRCA sheet, powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process, complete with all switch gears rotory handles, terminal spreader, shroud, Aluminium bus bars, SMC/FRP bus bar supports, PVC sleeve, dust tight doors with neoprene gasket, earthing the doors, Cable box with detachable gland plate, provision for supporting the cables, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. per detailed technical specifications consisting of the following . Incomer : 160A,TPN Isolator with indication lamp- 1Nos Busbars: Al busbar sized suitably for 160A TPN and 25X3 mm cu for Earth Outgoings: 100A, 25kA, TP, MCCB - 3Nos 63A, 25kA, TP, MCCB - 2Nos, 40A, TP, MCB C curve - 1No,32A, TP, MCB C curve - 1No

od235647/2024_2025 : DIAGNOSTIC BLOCK - LIGHT ; RP PANEL Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, LT panel board fabricated using 16/14 SWG CRCA sheet, powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process, complete with all switch gears rotory handles, terminal spreader, shroud, Aluminium bus bars, SMC/FRP bus bar supports, PVC sleeve, dust tight doors with neoprene gasket, earthing the doors, Cable box with detachable gland plate, provision for supporting the cables, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. per detailed technical specifications consisting of the following . Incomer : 160A,TPN Isolator with indication lamp- 1Nos Busbars: Al busbar sized suitably for 160A TPN and 25X3 mm cu for Earth Outgoings: 63A, 25kA, TP, MCCB - 6Nos, 40A, 25kA, TP, MCCB - 1No

od235648/2024_2025 : DIAGNOSTIC BLOCK - HVAC PANEL Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, LT panel board fabricated using 16/14 SWG CRCA sheet, powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process, complete with all switch gears rotory handles, terminal spreader, shroud, Aluminium bus bars, SMC/FRP bus bar supports, PVC sleeve, dust tight doors with neoprene gasket, earthing the doors, Cable box with detachable gland plate, provision for supporting the cables, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. per detailed technical specifications consisting of the following . Incomer : 200A,TPN Isolator with indication lamp- 1Nos Busbars: Al busbar sized suitably for 200A TPN and 25X3 mm cu for Earth Outgoings: 63A, 25kA, TP, MCCB - 3Nos, 40A, 25kA, TP, MCCB - 3Nos

od235649/2024_2025 : DIAGNOSTIC BLOCK - UPS PANEL Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, LT panel board fabricated using 16/14 SWG CRCA sheet, powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process, complete with all switch gears rotory handles, terminal spreader, shroud, Aluminium bus bars, SMC/FRP bus bar supports, PVC sleeve, dust tight doors with neoprene gasket, earthing the doors, Cable box with detachable gland plate, provision for supporting the cables, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. per detailed technical specifications consisting of the following . Incomer : 125A,TPN Isolator with indication lamp- 1Nos Busbars: Al busbar sized suitably for 125A TPN and 25X3 mm cu for Earth Outgoings: 63A, 25kA, TP, MCCB - 3Nos, 40A, 25kA, TP, MCCB - 4Nos

od235650/2024_2025 : DIAGNOSTIC BLOCK - LIFT PANEL Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, LT panel board fabricated using 16/14 SWG CRCA sheet, powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process, complete with all switch gears rotory handles, terminal spreader, shroud, Aluminium bus bars, SMC/FRP bus bar supports, PVC sleeve, dust tight doors with neoprene gasket, earthing the doors, Cable box with detachable gland plate, provision for supporting the cables, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. per detailed technical specifications consisting of the following . Incomer : 100A,FP Isolator with indication lamp- 1Nos Busbars: Al busbar sized suitably for 100A TPN and 25X3 mm cu for Earth Outgoings: 63A, TP, MCB C curve- 4Nos

od235651/2024_2025 :WARD TOWER ; DIAGNOSTIC BLOCK - LIFT SUB DISTRIBUTION PANELS: Supply, installation testing and commissioning of Sub Main Distribution Panel Board with Isolator / MCCB incomer and MCCB outgoing. TPN switch gear shall be supplied with equally rated neutral link and all MCCBs shall be with rotary handle.Incomer : 63A,FP Isolator with indication lamp- 1Nos Busbars: Al busbar sized suitably for 63A TPN and25X3 mm cu for Earth Outgoings: 32A, 4P, RCCB, 300mA - 1No 25A, 2P, RCCO, 30mA - 1No 10A, 1P, B Curve, MCB - 4Nos

od235652/2024_2025 : WARD TOWER - LIGHT ; RP PANEL Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, LT panel board fabricated using 16/14 SWG CRCA sheet, powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process, complete with all switch gears rotory handles, terminal spreader, shroud, Aluminium bus bars, SMC/FRP bus bar supports, PVC sleeve, dust tight doors with neoprene gasket, earthing the doors, Cable box with detachable gland plate, provision for supporting the cables, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. per detailed technical specifications consisting of the following . Incomer : 250A,TPN Isolator with indication lamp- 1Nos Busbars: Al busbar sized suitably for 250A TPN and 25X3 mm cu for Earth Outgoings: 63A, 25kA, TP, MCCB - 14Nos

od235653/2024_2025 :WARD TOWER -UTILITY PANEL-Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, LT panel board fabricated using 16/14 SWG CRCA sheet, powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process, complete with all switch gears rotory handles, terminal spreader, shroud, Aluminium bus bars, SMC/FRP bus bar supports, PVC sleeve, dust tight doors with neoprene gasket, earthing the doors, Cable box with detachable gland plate, provision for supporting the cables, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. per detailed technical specifications consisting of the following . Incomer : 250A,TPN Isolator with indication lamp- 1Nos Busbars: Al busbar sized suitably for 250A TPN and 25X3 mm cu for Earth Outgoings: 100A, 25kA, TP, MCCB - 3Nos 63A, 25kA, TP, MCCB - 4Nos,

od235654/2024_2025 : WARD TOWER -CSSD PANEL-Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, LT panel board fabricated using 16/14 SWG CRCA sheet, powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process, complete with all switch gears rotory handles, terminal spreader, shroud, Aluminium bus bars, SMC/FRP bus bar supports, PVC sleeve, dust tight doors with neoprene gasket, earthing the doors, Cable box with detachable gland plate, provision for supporting the cables, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. per detailed technical specifications consisting of the following . Incomer : 200A,FP Isolator with indication lamp- 1Nos Busbars: Al busbar sized suitably for 200A TPN and 25X3 mm cu for Earth Outgoings: 125A, 25kA, TP, MCCB - 3Nos 63A, 25kA, TP, MCCB - 1No, 40A, 25kA, TP, MCCB - 4Nos

od235655/2024_2025 :WARD TOWER -HVAC PANEL-Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, LT panel board fabricated using 16/14 SWG CRCA sheet, powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process, complete with all switch gears rotory handles, terminal spreader, shroud, Aluminium bus bars, SMC/FRP bus bar supports, PVC sleeve, dust tight doors with neoprene gasket, earthing the doors, Cable box with detachable gland plate, provision for supporting the cables, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. per detailed technical specifications consisting of the following . Incomer : 320A,FP Isolator with indication lamp- 1Nos Busbars: Al busbar sized suitably for 320A TPN and 25X3 mm cu for Earth Outgoings: 63A, 25kA, TP, MCCB - 7Nos 40A, 25kA, TP, MCCB - 5Nos

od235656/2024_2025 :WARD TOWER- UPS PANEL Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, LT panel board fabricated using 16/14 SWG CRCA sheet, powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process, complete with all switch gears rotory handles, terminal spreader, shroud, Aluminium bus bars, SMC/FRP bus bar supports, PVC sleeve, dust tight doors with neoprene gasket, earthing the doors, Cable box with detachable gland plate, provision for supporting the cables, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. per detailed technical specifications consisting of the following . Incomer : 200A,TPN Isolator with indication lamp- 1Nos Busbars: Al busbar sized suitably for 200A TPN and 25X3 mm cu for Earth Outgoings: 125A, 25kA, TP, MCCB - 2Nos, 63A, 25kA, TP, MCCB - 4Nos

od235657/2024_2025 : WARD TOWER - LIFT PANEL Supply, installation testing and commissioning of LT Floor mounted, compartmentalised dust and vermin proof, LT panel board fabricated using 16/14 SWG CRCA sheet, powder coated with two coats paint over two coats of zinc chromate primer, before painting the panel board shall be treated through 7-tank cold pre-treatment process, complete with all switch gears rotory handles, terminal spreader, shroud, Aluminium bus bars, SMC/FRP bus bar supports, PVC sleeve, dust tight doors with neoprene gasket, earthing the doors, Cable box with detachable gland plate, provision for supporting the cables, control wiring, metering, all protective relays, interlocks and instrumentation system suggested by Electrical inspectorate, etc. per detailed technical specifications consisting of the following . Incomer : 100A,FP Isolator with indication lamp- 1Nos Busbars: Al busbar sized suitably for 100A TPN and 25X3 mm cu for Earth Outgoings: 63A, TP, MCB C curve- 6Nos

od235658/2024_2025 :WARD TOWER- APFC Panel 200 KVAR :SITC of 8 Stage Automatic Power Factor Correction Panel made of 14/16SWG thick CRCA sheet fully compartmentalized, dust and vermin proof, degreased, pickling, zinc phosphate and powder coating painted with approved colour and quality, complete with hinged and earthed front doors, name plate, danger notice board, heavy duty neoprene gaskets, removable gland plates made of 3mm thick sheet steel boards with 500V, APPH, Heavy Duty Capacitor and 7% detuned reactors, Capacitor Duty contactor and microprocessor based APFC Relay in steps of 8 with all required accessories. Including capacitor duty contactor, auxiliary contactor, (2 no+ 2nc), auxiliary contactor add on, (2 no+ 2nc), fan, air vent, auto manual ON/OFF indication switch, cooling fan etc. Incomer: 400A 4P Isolator - 1 No microprocessor based APFC Relay (8 Steps) - 1No, 400/5A, CL- 1, CT, 10VA 3 Nos, Multi-function digital meter - 1Set, RYB Indication Lamp - 1Set Bus bars: 400A Al bus bar, Cu Earth bus. Outgoings: 100A SFU FUSE - 5Nos, 63A SFU FUSE 4 Nos Contactor - 100A TP Contactor-4 No. 63/40A, 3P, Contactor - 4Nos. 1. 30kVAr APPH, 500V with 7% detuned reactor,capacitor duty contactor, ON/Off indication lamp 3 Set,2. 25kVAr APPH, 500V with 7% detuned reactor - 1Set, 3. 20kVAr APPH, 500V with 7% detuned reactor - 2 sets, 4. 10kVAr APPH, 500V with 7% detuned reactor - 1sets, 5. 5kVAr APPH, 500V with 7% detuned reactor -1Sets, 6. (one number 30kVAR as fixed capacitor).

od235659/2024_2025 :DIAGNOSTIC - APFC Panel 120 KVAR :SITC of 8 Stage Automatic Power Factor Correction Panel made of 14/16SWG thick CRCA sheet fully compartmentalized, dust and vermin proof, degreased, pickling, zinc phosphate and powder coating painted with approved colour and quality, complete with hinged and earthed front doors, name plate, danger notice board, heavy duty neoprene gaskets, removable gland plates made of 3mm thick sheet steel boards with 500V, APPH, Heavy Duty Capacitor and 7% detuned reactors, Capacitor Duty contactor and microprocessor based APFC Relay in steps of 8 with all required accessories. Including capacitor duty contactor, auxiliary contactor, (2 no+ 2nc), auxiliary contactor add on, (2 no+ 2nc), fan, air vent, auto manual ON/OFF indication switch, cooling fan etc. Incomer: 250A 4P Isolator - 1 No microprocessor based APFC Relay (8 Steps) - 1No, 250/5A, CL- 1, CT, 10VA 3 Nos, Multi-function digital meter - 1Set, RYB Indication Lamp - 1Set Bus bars: 250A Al bus bar, Cu Earth bus. Outgoings: 100A SFU FUSE - 2Nos, 63A SFU FUSE 5 Nos , 40A SFU FUSE 1No, Contactor - 100A TP Contactor-1 No. 63/40A, 3P, Contactor - 7Nos. 1. 25kVAr APPH, 500V with 7% detuned reactor,capacitor duty contactor, ON/Off indication lamp 1 Set,2. 20kVAr APPH, 500V with 7% detuned reactor - 1Set, 3. 10kVAr APPH, 500V with 7% detuned reactor - 4 sets, 4. 5kVAr APPH, 500V with 7% detuned reactor -2Sets, 5. (one number 25kVAR as fixed capacitor).

DISTRIBUTION BOARD / RCCB / ISOLATOR / MCBs

2.2.1 : Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required100 Amp, 16 KA, TPMCCB

2.2.2 : Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required125 Amp,16 KA,TPMCCB

2.3.2 : Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator8 way, Double door

2.3.3 : Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator12 way, Double door

2.4.1 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)4 way (4 + 12), Double door

2.4.2 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way (4 + 18), Double door

2.4.3 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way (4 + 24), Double door

2.5.1 : Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)4 way (4 + 12), Double door

2.5.2 : Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)8 way (4 + 24), Double door

2.5.3 : Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)12 way (4 + 36), Double door

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.10.2 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole and netural

2.10.3 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole

2.10.4 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

2.10.5 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole and neutral

2.12.1 : Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.12.2 : Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.13.1 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.13.2 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.13.3 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.100 amps

2.14.1 : Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 amps

2.14.2 : Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.14.3 : Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.15.1 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 amps

2.15.2 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.15.3 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

od238511/2024_2025 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, 100mA, RCBO, in the existing MCB DB complete with connections, testing and commissioning etc. as required. 32 amps

od238512/2024_2025 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, 100mA, RCBO, in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

od238513/2024_2025 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, 100mA, RCBO, in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

2.11 : Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

1.26 : Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

2.16 : Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32amps 240 volts "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

2.17 : Supplying and fixing TP sheet steel enclosure on surface/ recess along with 16/25/32amps 415 volts "C" curve TP MCB complete with connections, testing and commissioning etc. as required.

2.18 : Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth,metal enclosed plug top along with 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

2.19 : Supplying and fixing 20 amps 415volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top along with 20 amps "C" curve, TPMCB, in sheet enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

2.23.2 : Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with testing and commissioning etc. as required. 2For 8 way, Double door SPN MCBDB

2.23.4 : Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with testing and commissioning etc. as required. 2For 14 way, Double door SPN MCBDB

2.24.1 : Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.For 4 way, Double door TPN MCBDB

2.24.2 : Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.For 6 way, Double door TPN MCBDB

2.24.3 : Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.For 8 way, Double door TPN MCBDB

2.25 : Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for tripple pole and neutral, sheet steel, Vertical MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.

LT CABLES

od235600/2024_2025 : Supply, testing and commissioning of the following size 1.1kV grade (AYWY/AYFY) / (XLPE) insulated PVC sheathed, armoured Aluminium conductor power LT cable confirming to IS 7098 (part 1) ammended upto date.1 X 3.5C X 400 Sqm

od235601/2024_2025 : Supply, testing and commissioning of the following size 1.1kV grade (AYWY/AYFY) / (XLPE) insulated PVC sheathed, armoured Aluminium conductor power LT cable confirming to IS 7098 (part 1) ammended upto date.1 x 3.5C x 300 Sq.mm.

od235602/2024_2025 : Supply, testing and commissioning of the following size 1.1kV grade (AYWY/AYFY) / (XLPE) insulated PVC sheathed, armoured Aluminium conductor power LT cable confirming to IS 7098 (part 1) ammended upto date.1 x 3.5C x 240 Sq.mm.

od235603/2024_2025 : Supply, testing and commissioning of the following size 1.1kV grade (AYWY/AYFY) / (XLPE) insulated PVC sheathed, armoured Aluminium conductor power LT cable confirming to IS 7098 (part 1) ammended upto date.1 x 3.5C x 185 Sq.mm.

od235604/2024_2025 : Supply, testing and commissioning of the following size 1.1kV grade (AYWY/AYFY) / (XLPE) insulated PVC sheathed, armoured Aluminium conductor power LT cable confirming to IS 7098 (part 1) ammended upto date.1 x 3.5C x 150 Sq.mm.

od235605/2024_2025 : Supply, testing and commissioning of the following size 1.1kV grade (AYWY/AYFY) / (XLPE) insulated PVC sheathed, armoured Aluminium conductor power LT cable confirming to IS 7098 (part 1) ammended upto date.1 x 3.5C x 120 Sq.mm.

od235606/2024_2025 : Supply, testing and commissioning of the following size 1.1kV grade (AYWY/AYFY) / (XLPE) insulated PVC sheathed, armoured Aluminium conductor power LT cable confirming to IS 7098 (part 1) ammended upto date.1 x 3.5C x 95 Sq.mm.

od235607/2024_2025 : Supply, testing and commissioning of the following size 1.1kV grade (AYWY/AYFY) / (XLPE) insulated PVC sheathed, armoured Aluminium conductor power LT cable confirming to IS 7098 (part 1) ammended upto date.1 x 3.5C x 70 Sq.mm.

od235608/2024_2025 : Supply, testing and commissioning of the following size 1.1kV grade (AYWY/AYFY) / (XLPE) insulated PVC sheathed, armoured Aluminium conductor power LT cable confirming to IS 7098 (part 1) ammended upto date.1 x 3.5C x 50 Sq.mm.

Supply, testing and commissioning of the following size 1.1kV grade (AYWY/AYFY) / (XLPE) insulated PVC sheathed, armoured Aluminium conductor power LT cable confirming to IS 7098 (part 1) ammended upto date.1 x 3.5C x 35 Sq.mm.

od235610/2024_2025 : Supply, testing and commissioning of the following size 1.1kV grade (AYWY/AYFY) / (XLPE) insulated PVC sheathed, armoured Aluminium conductor power LT cable confirming to IS 7098 (part 1) ammended upto date.1 x 3.5C x 25 Sq.mm.

od235611/2024_2025 : Supply, testing and commissioning of the following size 1.1kV grade (AYWY/AYFY) / (XLPE) insulated PVC sheathed, armoured Aluminium conductor power LT cable confirming to IS 7098 (part 1) ammended upto date.1 x 4C x 16 Sq.mm.

od235612/2024_2025 : Supply, testing and commissioning of the following size 1.1kV grade (AYWY/AYFY) / (XLPE) insulated PVC sheathed, armoured Aluminium conductor power LT cable confirming to IS 7098 (part 1) ammended upto date.1 x 4C x 10 Sq.mm.

od235613/2024_2025 : Supply, testing and commissioning of the following size 1.1kV grade (AYWY/AYFY) / (XLPE) insulated PVC sheathed, armoured Aluminium conductor power LT cable confirming to IS 7098 (part 1) ammended upto date.1 x 4C x 6 Sq.mm.

od235614/2024_2025 : Supply, testing and commissioning of the following size 1.1kV grade (AYWY/AYFY) / (XLPE) insulated PVC sheathed, armoured Aluminium conductor power LT cable confirming to IS 7098 (part 1) ammended upto date.1 x 4C x 4 Sq.mm.

od235615/2024_2025 : Supply testing and commissioning of the single core FR PVC insulated Armoured Copper Cable for working voltage upto and including 1100 V 1 x 4C x 2.5 Sq.mm.

od235616/2024_2025 : Supply testing and commissioning of the single core FR PVC insulated Armoured Copper Cable for working voltage upto and including 1100 V 1x 3C x 2.5 Sq.mm.

od235617/2024_2025 : Supply testing and commissioning of the single core FR PVC insulated Armoured Copper Control Cable for working voltage upto and including 1100 V 12C x 1.5 Sq.mm

od238516/2024_2025 : Supply and laying of PVC insulated copper wire of size 16sqmm including termination in the existing conduit

od238517/2024_2025 : Supply and laying of PVC insulated copper wire of size 25sqmm including termination in the existing conduit

od238518/2024_2025 : Supply and laying of PVC insulated copper wire of size 35sqmm including termination in the existing conduit

LT CABLE LAYING

7.1.1 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Upto 35 sq. mm

7.1.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 35 sq. mm and upto 95 sq. mm

7.1.3 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 95 sq. mm and upto 185 sq. mm

7.1.4 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 185 sq. mm and upto 400 sq. mm

7.5.1 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Upto 35 sq. mm

7.5.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 35 sq. mm and upto 95 sq. mm

7.5.3 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 95 sq. mm and upto 185 sq. mm

7.5.4 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 185 sq. mm and upto 400 sq. mm

7.7.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.7.2 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

7.7.3 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

7.7.4 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

7.8.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.8.2 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

7.8.3 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

7.8.4 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

7.9 : Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.

LT CABLE END TERMINATION

9.1.31 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 400 sq. mm (82mm)

9.1.30 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 300 sq. mm (70mm)

9.1.29 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 240 sq. mm (62mm)

9.1.27 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 185 sq. mm (57mm)

9.1.26 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 150 sq. mm (50mm)

9.1.25 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 120 sq. mm (45mm)

9.1.24 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 95 sq. mm (45mm)

9.1.23 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.22 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 50 sq. mm (35mm)

9.1.21 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 35 sq. mm (32mm)

9.1.20 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X25 sq.mm (28mm)

9.1.33 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

9.1.32 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

od238531/2024_2025 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 1x 4C x 6 Sq.mm.

od238532/2024_2025 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 1x 4C x 4 Sq.mm.

od238533/2024_2025 : Supply of all materials and termination of the following FR PVC insulated flexible copper cable using single compression type cadmium plated brass cable glands, Copper crimped type cable lugs, cable identification tags and including gland earthing using copper conductor of adequate size , AL-CU strip for termination of Cables etc. -1x 4C x 2.5 Sq.mm.

od238534/2024_2025 : Supply of all materials and termination of the following FR PVC insulated flexible copper cable using single compression type cadmium plated brass cable glands, Copper crimped type cable lugs, cable identification tags and including gland earthing using copper conductor of adequate size , AL-CU strip for termination of Cables etc.-1x 3C x 2.5 Sq.mm.

od238535/2024_2025 : Supply of all materials and termination of the following FR PVC insulated flexible copper cable using single compression type cadmium plated brass cable glands, Copper crimped type cable lugs, cable identification tags and including gland earthing using copper conductor of adequate size , AL-CU strip for termination of Cables etc. -12C x 1.5 Sq.mm

CEILING FAN /WALL FAN/ EXHAUST FANS

od29502/2025_2026Supply, installation, testing commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with regulator type Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, power factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

od29503/2025_2026 Supply, installation, testing commissioning of 300mm sweep heavy duty exhaust fan in metal frame working on 230V A/C.The work shall include making the holes suitable for the size of fan, fixing necessary bolt and nuts making good the damages, etc. and giving connection with required length of 1.5sq.mm, 3 core PVC insulated and PVC sheathed copper conductor flexible wire conforming to ISS, etc. as required.

od29504/2025_2026 Supply, installation, testing and commissioning of wall fan, 450 mm sweep, 230V, 1Ph, metal body and blades, pull cord for speed regulation, thermal overload protection for motor, min speed (rpm) & 1200, min air delivery (CMM) & 75 complete with all mounting accessories as required.

CABLE TRAYS

4.1.3 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.225 mm width X 50 mm depth X 1.6 mm thickness

4.1.4 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.300 mm width X 50 mm depth X 1.6 mm thickness

4.1.6 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.450 mm width X50 mm depth X 2.0 mm thickness

4.1.7 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.600 mm width X 50 mm depth X 2.0 mm thickness

4.1.2 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.150 mm width X 50 mm depth X 1.6 mm thickness

WIRING IN PVC CONDUITS

1.10.3 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.11 : Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

1.55.3 : Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

od238541/2024_2025 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm in existing PVC conduit (in slab only), with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLSPVC insulated copper conductor single core cable etc as required.Group C

1.14.1 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

1.14.2 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.3 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.14.4 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 6 Sq.mm + 1 x 6 sq.mm earth wire

1.14.5 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 10 sq. mm + 1 X 6 sq. mm earth wire

1.17.3 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm

1.17.12 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

1.17.21 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 4 sq. mm

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.3 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

1.21.4 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.40 mm

1.21.5 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.50 mm

1.22.1 : Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.75 mm X 75 mm X 60 mm deep

1.22.2 : Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.100 mm X 100 mm X 60 mm deep

1.22.3 : Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.150 mm X 75 mm X 60 mm deep

1.22.11 : Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.200 mm X 150 mm X 100 mm deep

1.24.1 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.2 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.2 way 5/6 amps switch

1.24.3 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.4 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.5 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.25 : Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

1.27.1 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.3 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.4 Module (125mmX75mm)

1.27.4 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

1.27.5 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.8 Module (125mmX125mm)

1.27.6 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.12 Module (200mmX150mm)

1.31 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

od239826/2024_2025 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

1.56 : Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlets and 2 Nos. 5/6 A modular switches, connection etc. as required. (For light plugs to be used in non residential buildings).

1.38 : Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

90.9.1.1 : Supply and fixing 50 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.50x50mm Cable Management System with base and lid

90.9.2.1 : Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.100 x 50 mm CMS with base and lid

od239832/2024_2025 :Supply and installation of disconnect switches (isolators) in metallic enclosures to provide power supply to mechanical equipment.160A TPN Isolator

od239833/2024_2025 : Supply and installation of disconnect switches (isolators) in metallic enclosures to provide power supply to mechanical equipment.125A TPN Isolator

od239834/2024_2025 : Supply and installation of disconnect switches (isolators) in metallic enclosures to provide power supply to mechanical equipment.63A TPN Isolator

EARTHING

5.2 : Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required

od238542/2024_2025 : Earthing with G.I. earth pipe 2.5 metre long, 40 mm dia including accessories, and providingmasonry enclosure with cover plate having locking arrangement and watering pipe etc. withcharcoal/ coke and salt as required

5.4 : Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

5.6 : Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

od239835/2024_2025 : Supply and installation charges for Providing 1200x 1200x12 mm Cast Iron plate earth station, conforming to IS 3043 filling with mixtures of salt, sand and charcoal, construction of earth chamber with brick masonry and covering with heavy duty Cast Iron Cover hinged to Cast Iron Frame, including excavation backfilling of earth pit.

od239836/2024_2025 : Supplying and laying 40mm x6mm copper strip at 0.50 metre below ground as strip earth electrode,including connection / terminating with nut,bolt,spring,washer etc.as required.(jointing shall be done by overlapping and with 2 sets of brass nut bolt amp; spring washer spaced at 50mm)

5.8 : Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

5.14 : Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

od239829/2024_2025 : Providing and fixing 25mm x 3mm copper strip on surface or in recess for connections etc as required.

od239830/2024_2025 : Providing and fixing 32mm x 6mm copper strip on surface or in recess for connections etc as required.

5.19 : Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

od239827/2024_2025 : Providing and fixing 10 SWG dia Copper wire on surface or in recess for loop earthing as required.

od239828/2024_2025 : Providing and fixing earth bus of 50mm x 5mm copper strip on surface for connections etc as required.

LIGHTINING PROTECTION

6.2 : Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube,having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

6.3 : Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required.

6.4 : Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

6.7 : Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

6.8 : Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

6.12 : Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

6.14 : Providing and laying G.l. tape 32 mm X 6 mm from earth. electrode directly in ground as required.

LIGHT FIXTURES

od238183/2024_2025 : Supply and fixing of 2X2, LED Recessed mount down light with 30W/32W with System efficiency of more than 100 lm/W and Translucent frosted diffuser for Uniform illumination and wider light distribution. The LED shall be compliant with life of 50000 Hrs tested at maximum current (Complete LM 80 test report for LED should be submitted for 10000 hrs of testing). The LEDs used should be with CT of 5700k and CRI of Minimum 80. LED Driver shall be Multistage, Isolated type, Constant Current topology driver with proper heat sink for heat dissipation suitable to operate in input voltage range of 140V to 270V.

od238184/2024_2025 : Supply and installation of recess mounted, 36/40W LED Cleanroom luminaire (2x2 feet), powder coated CRCA housing, high efficiency translucent diffuser including all necessary mounting accessories, flexible conduit and connection wire etc with following minimum requirements:- IP65, CCT 5700K, CRI 80, p.f 0.9, min. service life of LED - 50000 hours, Luminous efficacy 100 Lm/W, Surge protection of min 3kV, THD 10%, comply IEC 62471 for LED etc with all necessary accessories as required.

od238185/2024_2025 : Supply and fixing of 15W, IP20,LED Recess /surface mounted downlighter with Maximum system wattage of 15 W, System efficency 100lm/W and minimum system lumen output 1200 lm, White powder coated, pressure die cast aluminium housing. Luminaire shall use SMD type LED with CRI more than 80, THD less than 10% with PF more than 0.95 with inbuilt Surge Protection of 2.5KV.

od238186/2024_2025 : Supply and fixing of 6W, IP20,LED Recess /surface mounted Round downlighter with Maximum system wattage of 6 W, System efficency 100 lm/W and minimum system lumen output 1200 lm, White powder coated, pressure die cast aluminium housing. Luminaire shall use SMD type LED with CRI more than 80, THD less than 10% with PF more than 0.95 with inbuilt Surge Protection of 2.5KV.

od238187/2024_2025 : Supply and fixing 20W IP20 High efficient 1.2m long LED batten surface/wall mounted Specially designed Co-extruded channel in thermally conductive material with plastic with HET diffuser. In-built electronic driver duly wired up to terminal block. CRI greater than or equal to 80, Temperature range-0 to 50DegC, Driver efficiency g85%, Power factorgreater than or equal;0.9, CT - 6500K, THD20%, Surge protection 2kV, 30000 burning hours Luminaire lumen 2200 lumens (110 lm/W).

od238188/2024_2025 : Supply and fixing of 10W IP20 High efficient 0.6m long LED batten surface/wall mounted Specially designed Co-extruded channel in thermally conductive material with plastic with HET diffuser. In-built electronic driver duly wired up to terminal block.IP20, CRI greater than or equal;80, Temperature range-0 to 50DegC, Driver efficiencygreater than or equal;85%, Power factor 0.95, CCT - 6500K, THD20%, Surge protection 2kV, 30000 burning hours Luminaire lumen 1000 lumens (100lm/W).

od238189/2024_2025 : Supply of Integral, SMD LED, IP 66, 9W, LED Surface mounted Die cast Alumium Bulk head fixture with System efficacy of more than 70 lm/W. Luminaire shall have Polycarbonate high transmitivity diffuser for Uniform illumination and wider light distribution. LED luminaire shall have specially design aluminum heat sink for excellent heat dissipation, good air circulations as well as very light weight.The luminaire should have inbuilt SPD -2.5KV with CRI more than 70, Power factor 0.95, THD less than 10%.

od238190/2024_2025 : Supply and fixing of weather proof, 3D signage board 1m height and 4 m wide fabricated with Angle iorn strucure and 14SWG CRCA sheet, fixing of 3D, letters made using 2mm thick acrylic sheet, each lettee is illuminated with sufficient LED rope including 12V dc power controller for LED ( each letter consist two layer LED as aproved )

od238191/2024_2025 : Supply and installation of 30W street light including 32 mm GI pipe ,1.5 meter for support -Garnet LED Light Cool White and all accessories for complete.

EXTERNAL LIGHTING

od238543/2024_2025 : Supply installation testing commissioning of Octogaonal Pole made of hot dip galvanised GI sheet 70mm top diameter, 130mm bottom diameter thickness 3mm base plate dimensions of 200x200x12mm suitable for wind speed as per IS 875 Part III single arm bracket 0.5mt including connector foundation bolt 4 nos fixed in existing RCC foundation and junctions box etc. complete 5 Meters. The pole shall have inbuilt cable loop in loop out with flush door and locking facility. The loop in loop out shall be provided with 4A SP C curve MCB, loop in loop out terminals block, required dia GI / PVC pipe from foundation for taking cable in ; out from the pole, 3Cx1.5sqmm unarmounred PVC insulated round copper cable from loop in loop out to light fixture etc with all required accessories.

od238544/2024_2025 : Supply installation testing commissioning of Octogaonal Pole made of hot dip galvanised GI sheet 70mm top diameter, 130mm bottom diameter thickness 3mm base plate dimensions of 200x200x12mm suitable for wind speed as per IS 875 Part III double arm bracket 0.5mt including connector foundation bolt 4 nos fixed in existing RCC foundation and junctions box etc.complete 5 Meters. The pole shall have inbuilt cable loop in loop out with flush door and locking facility. The loop in loop out shall be provided with 4A SP C curve MCB, loop in loop out terminals block, required dia GI / PVC pipe from foundation for taking cable in ; out from the pole, 3Cx1.5sqmm unarmounred PVC insulated round copper cable from loop in loop out to light fixture etc with all required accessories.

90.15.3.2 : Supply installation testing commissioning of Octogaonal Pole made of hot dip galvanised GI sheet 70mm top diameter, 130mm bottom diameter thickness 3mm base plate dimensions of 200x200x12mm suitable for wind speed as per IS 875 Part III double arm bracket 0.5mt including connector foundation bolt 4 nos fixed in existing RCC foundation and junctions box etc.complete 5 Meters

90.15.4.1 : Supply Conveyance, installation, testing and commissioning of 20W LED street light output greater than 105lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/Lumilled/Nichea with power factor greater than 0.95 at full load, internal surge protection up to 8 KV,and Aluminium pressure die-cast Powder coated housing,acrylic cover complete with THD Less than10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be seperatly accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer)

SOLAR PV SYSTEM

od235758/2024_2025 : Supply Installation Testing and Commissioning of following type solar PV systems having all protective devices, AC ;amp; DC distribution board with MCBs and surge protective devices, AC distribution panel having 1 no 125A isolator and 2/3 nos 63A MCBs, 3 Phase 4 wire -/5A,Cl 0.2s energy meter including CTs ,Supply and fixing HT CT net meter necessary cabling including DC cable for panel to inverter / DC DB and AC cabling from inverter to AC DB , AC panel and Main panel ,all civil and mechanical works for supporting, earthing using proper cable /strip, earth electrode and lightning protection system as directed by electrical inspectorate, preparation of design and getting approval from Electrical inspectorate /KSEBL and getting energization sanction, all the works shall comply the MNRE standards. Diagnostic block- 30 kWp monocrystalline solar PV panels,30kW grid connected string inverter having all protective devices

od235759/2024_2025 : Supply Installation Testing and Commissioning of following type solar PV systems having all protective devices, AC ;amp; DC distribution board with MCBs and surge protective devices, AC distribution panel having 1 no 125A isolator and 2/3 nos 63A MCBs, 3 Phase 4 wire -/5A,Cl 0.2s energy meter including CTs ,Supply and fixing HT CT net meter necessary cabling including DC cable for panel to inverter / DC DB and AC cabling from inverter to AC DB , AC panel and Main panel ,all civil and mechanical works for supporting, earthing using proper cable /strip, earth electrode and lightning protection system as directed by electrical inspectorate, preparation of design and getting approval from Electrical inspectorate /KSEBL and getting energization sanction, all the works shall comply the MNRE standards.Ward tower- 40 kWp monocrystalline solar PV panels,40kW grid connected string inverter having all protective devices

od235760/2024_2025 : Providing and fixing steel structure for supporting solar PV panel up to a height of 3 meter from floor level including fixing of tubular poles ,purling ,anchor faster for complete installation

MISCELLANEOUS ITEMS

od238561/2024_2025 : Supply and installation of elastomer mat with ISI mark suitable for 11 KV,2.5mm THICK installation conforming to IS:15652:2006

od238562/2024_2025 : Supply and installation of 2nos fire buckets along with stand painted with enamel paint of red colour.

od238563/2024_2025 : Supply and installation of emergency OFF trip push button with front Glass and painted in RED Colour.

od238564/2024_2025 : Supply and Installation of Cable route marker for HT UG Cable at every 10m interval made of Cast Iron ( 152mm Round )

od238565/2024_2025 : Supply and fixing CO2 type 4.5KG capacity trolley mounted fire extinguishers as appoved by ISI complete as required

od238566/2024_2025 : Supply and installation of Danger board as required by the electrical authorities.

od238567/2024_2025 : Supply and installation of Laminated copies of Approved/ as built schemes and drawings in electrical room

od238568/2024_2025 : Supply of Insulated hand gloves IS 4770/1991

od238569/2024_2025 : Providing and laying in position reinforced cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation

od238570/2024_2025 : Providing brick work (in width 225 mm or more) with F.P.S. bricks of class designation 7.5 in cement mortar 1:4 (1 cement : 4 coarse sand) at all levels.

od238571/2024_2025 : Providing 15mm thick cement plaster of mix 1:4 (1 cement : 4 fine sand) at all levels.

od238572/2024_2025 : Supply fabrication, painting with two coats of synthetic enamel paint over a coat of zink chromate primer and erection of MS structural steel ( Angle iron/ flats/T section) for supporting the equipments, exhaust line etc complete

14.13.1 : Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required50 mm dia

14.13.2 : Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required80 mm dia

14.13.3 : Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required100 mm dia

14.13.4 : Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required150 mm dia

14.14.2 : Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.150 mm dia

14.14.4 : Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.300 mm dia

14.16.1 : Supplying and laying of following size DWC HOPE pipe lSI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 em below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. , complete as required.63 mm dia (OD-63 mm & ID-51 mm nominal)

14.16.2 : Supplying and laying of following size DWC HOPE pipe lSI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 em below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. , complete as required.90 mm dia (OD-90 mm & ID-76 mm nominal)

14.16.3 : 120 mm dia (OD-120 mm & ID-103 mm nominal)

ELV SERVICE WORKS

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.3 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

1.21.4 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.40 mm

1.21.5 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.50 mm

4.6.2 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.150 mm width X 50 mm depth X 1.6 mm thickness

4.6.4 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.300 mm width X 50 mm depth X 1.6 mm thickness

4.6.6 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.450 mm width X 50 mm depth X 2.0 mm thickness

1.53.1 : Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable

1.53.2 : Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required2 run of Cable

1.53.3 : Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required3 run of Cable

1.27.1 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

DATA SYSTEM

od239763/2024_2025 : Supply and fixing of GI modular box including modular face plates, fixing of RJ 45 outlets and termination of Cat 6 cables on the outlets

od239770/2024_2025 : Supply installation testing and commissioning of 24 Port fully-loaded patch panel with necessary mechanical supports

od239773/2024_2025 :Supply, installation, testing, and commissioning of 24 ports 10G SFP+ + 4 ports 100G QSFP28 Ports L3Managed Switch - Core Switch with all required accessories.

od239779/2024_2025 : Supply, installation, testing and commissioning of 20 10/100/1000 BASE-T ports + 4port 1G SFP ports,+ 4 10GSFP+ ports L3 Stackable Managed Switch - Core Switch with all required accessories.

od239785/2024_2025 : Supply ;fixing of 10G SFP+ Module to L3 Stackable Managed Switch(Floor S/w)

od239792/2024_2025 : Supply, installation, testing ; commissioning of Fibre PATCH CORD LC-SC SM DUPLEX LENGTH- 1m with all required accessories.

od239796/2024_2025 :Supply, installation, testing ; commissioning of PIGTAIL SC SM SIMPLEX LENGTH- 1m with all requiredaccessories.

od239801/2024_2025 : Supply installation testing and commissioning of 42U Rack 1000 mm Depth with cable manager, power sockets and all other accessories

od239809/2024_2025 : Supply installation testing and commissioning of 22 U Rack 600 mm depth with cable manager, power sockets and all other accessories

od239812/2024_2025 : Supply and laying of Fiber Optic Cable 6 core SM Indoor / Outdoor Cable through the existing PVC conduit including splicing and termination at both ends

od239817/2024_2025 : Providing and termination of LIU 06 Port Rackmount Blank with Splice Tray and Cable spool (SC) SM and including all accessories like pigtails, sleeves, etc.

od239819/2024_2025 : Providing and termination of LIU 12 Port Rackmount Blank with Splice Tray and Cable spool (SC) SM and including all accessories like pigtails, sleeves, etc.

od239822/2024_2025 : Providing LIU 24 Port Rackmount .with modules splice Tray and Cable spool (SC) SM and including all accessories like pigtails, sleeves, etc.

TELEPHONE SYSTEM

od239765/2024_2025 : Supplying, installation, testing ; commissioning of ordinary telephones with connecting cords (minimum length of 2 metres) having a necessary connector at both ends

1.24.6 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Telephone socket outlet

od239776/2024_2025 : Supply,laying and termination of 10 pair telephone cable, 0.5mm copper PVC insulated,unarmoured telephone cable drawn in the existing cable tray

od239782/2024_2025 : Supply,laying and termination of 20 pair telephone cable, 0.5mm copper PVC insulated,unarmoured telephone cable drawn in the existing cable tray

od239789/2024_2025 : Supply,laying and termination of 50 pair telephone cable, 0.5mm copper PVC insulated,unarmoured telephone cable drawn in the existing cable tray

od239791/2024_2025 :Supply,fixing and termination of 10 pair telephone terminal blockhoused in engineering plastic box with transparent hinged door

od239799/2024_2025 :Supply,fixing and termination of 20 pair telephone terminal blockhoused in engineering plastic box with transparent hinged door

od239804/2024_2025 :Supply,fixing and termination of 50 pair telephone terminal blockhoused in engineering plastic box with transparent hinged door

od239808/2024_2025 : Supply,fixing and termination of Intermediate distribution frame of 60 pair with including all accessories as required.

od239811/2024_2025 : Supply,fixing and termination of 100 port telephone MDF

od239816/2024_2025 : Supply,laying and termination of Jelly filled 50 pair telephone armoured cable, (for building to building connection)

od239820/2024_2025 : Supply,laying and termination of Jelly filled 100 pair telephone armoured cable, (for building to building connection)

od239821/2024_2025 :Supply,installation,testing and commissioning of 208 analog lines with CLI expandable up to512 ports- 02PRIlines- 08 analog trunks with DTMF CLI and PFT- 02 nos Operator Console with 30key DSS- 08 port in-skin Voice Guidance card- IPM protection for analog trunk lines- 01 nos Call Billing ; monitoring s/w- FCBC with battery for 01hourbackup- System with warranty of 01year- 2nos 500 port MDF

CCTV SYSTEM

od239761/2024_2025 : Supply, Installation, Testing ; Commissioning of IP Network TDN Low-Light IR Indoor Dome Camera, 1/2.8 4 Megapixel progressive scan CMOS, should support upto 30fps, triple stream, Min. Illumination required 0.005Lux @f/1.6, B/W:0Lux@f/1.6(IR on), 120dB True WDR, Min. Pixels 1920x1080, triple stream,2.7-13.5 mm MFZ, DC IRIS, optical zoom 5x lens F1.6, Backlight Compensation, 3DNR, Privacy Mask, 3 IR LEDs Smart IR with upto 20m IR distance, H.265+, H.265, H.264 and MJPEG, Inbuilt Video Analytics : Tripwire/IntrusionTrace, Object Left Behind, Object removed. Dual channel Audio G.711a/G.711u/AAC, 128GB SD card support, IP 66, Alarm: 1 In ; 1out, PoE Class 3/ 12V DC/24VAC, Die-Cast Aluminium Construction, Having Operating temp range : 30deg;C to 60deg;C. Certifications: ONVIF Profile S ; Profile G compliant, UL CAP cybersecurity certification, UL, CE, EN, FCC ; RoHS compliant including all mounting accessories as required.

od239769/2024_2025 : Supply, Installation, Testing ; Commissioning of IP Network TDN Low-Light IR Outdoor Box/Bullet type Cameras, 1/2.8 CMOS, 4 MP @30fps, triple stream, Min. Illumination required 0.005Lux @f/1.6, B/W: 0Lux @f/1.6(IR on), 120dB True WDR, Min. Pixels 1920&times;1080p, triple stream,2.7-13.5 mm MFZ, DC IRIS, optical zoom 5x lens F1.6, Backlight Compensation, Highlight Compesation, 3DNR, Privacy Mask, Internal/External Smart IR LEDs with upto 60m IR distance, H.264; MJPEG, Inbuilt Video Analytics : Tripwire/IntrusionTrace, Object Removed, Object Left Behind. Dual channel Audio G.711a/G.711u/AAC, 128GB SD card support, IP 67 ; IK10, Alarm: 1 In ; 1out, PoE, H.264 High Profile and MJPEG, PoE Class 3/ 12V DC/24VAC,Die-Cast Aluminium Construction, Having Operating temp range : (40deg;C to 60deg;C). Certifications: ONVIF Profile S ; Profile G compliant, UL CAP certification, UL, CE, EN, FCC ; RoHS compliant including all mounting accessories as required.

od239777/2024_2025 : Supply, Installation, Testing ; Commissioning of IP Network TDN Low-Light PTZ Camera with auto tracking, 1/1.9 CMOS, 4 MP @ 30fps, triple stream, Min. Illumination required 0.005 lux @ F1.6 (color) ; 0.0005 lux @ F 1.6(B/W) or better, 120dB True WDR or better, Min. Pixels 1920 &times; 1080, triple stream, 6mm 180 mm or 4.5 to 135mm 30x motorized focus ; zoom lens, BLC, HLC, 3DNR, Defog, Electronic Image Stabilitzation, Privacy Mask, Internal / External Illuminatrion range with upto 200m IR distance, Dual channel Audio G.711a/G.711u/AAC, 128GB SD card support, Alarm: 7 In/ 2 out, PoE, H.264 High Profile and MJPEG, PoE Class 5 and 12V DC/24VAC, IP 67, IK 10 vandal proof, Having Operating temp range : 10&deg;C to 65deg; C. Certifications: ONVIF Profile S compliant, UL, CSA 60950-22, CE (EN 50130-4 ; EN 55022) , FCC Part 15 ; RoHS compliant with all mounts and accesories as required.

od239781/2024_2025 : Supply, installation, testing and commissioning 64 Channel Network Video Recorder 64-channel IP video access Smart H.265+/Smart H.264+/H.265/H.264/MJPEG; H.265 auto switch Max 320 Mbps incoming bandwidth Up to 24MP resolution for live view and playback 1-channel fisheye dewarping (AI by NVR) AI by Camera: Perimeter protection; face detection and recognition; SMD Plus; video metadata; ANPR; people counting; stereo analysis; crowd distribution; heat map . Up to 22 face pictures/sec processing;middot; Up to 20 face databases with 100,000 face images in total. Smart H.265+ is the optimized implementation of the H.265;;codec that uses a scene-adaptive encoding strategy, dynamic GOP, dynamic ROI, flexible multi-frame reference structure and intelligent noise reduction to deliver high-quality video without straining the network. ANPR Automatic Number Plate Recognition required for convenient entrance/ exit management. Support license plate recognition black/white list import/export, add/remove B/W list number, search result from recorded video. Internal HDD 8 SATA III Ports, Up to 10 TB capacity for each HDD eSATA 1 eSATA Interface 2 RJ-45 Ports (10/100/1000Mbps)Independent or Joint Working PoE N/A Network Function HTTP, HTTPS, TCP/IP, IPv4/IPv6, UPnP, SNMP, RTSP,UDP, SMTP, NTP, DHCP, DNS, IP Filter, PPPoE, DDNS,FTP, Alarm Server, IP Search (Support IP camera, DVR, NVS, etc.), P2P Max. User Access 128 users Smart Phone iPhone, iPad, Android Interoperability ONVIF 2.4, SDK, CGI Certification CE,FCC,UL,BIS

od239790/2024_2025 : Supply, installation, testing and commissioning of 24- Port 10/100/1000 Mbps PoE + 4port 10G SFP+ - Edge PoE Managed switch with all required accessories.

od239793/2024_2025 : Supply, installation, testing and commissioning of 8 port- PoE switch with 2 SFP Module

od239797/2024_2025 : Supply, installation, testing and commissioning of Patch Panel UTP Keystone- 24 Port- Fully loaded (Cat 6 )

od239803/2024_2025 : Supply and installation of Cat 6 UTP patch cord, 1 mtr

od239807/2024_2025 : Supply, installation, testing and commissioning of Server PC, Intel i7 processor, 24 inch LED monitor, Gigabit LAN port, USB port, 16 GB DDR3 RAM,1TB SSD,1GB dual graphic card, 100/1000 LAN ports, optical mouse, Keyboard, DVD Writer. Lateste windows with antivirous of 3year subcription, 24 inch LED monitor

od239810/2024_2025 : Supply, installation, testing and commissioning of Professional Joystick designed for Surveillance application as compatible with the above mentioned system. UL+CE+FCC certification minimum.

od239815/2024_2025 : Supply, installation, testing and commissioning of Surveillance / SATA compatible Hard Disk of 10 TB capacity to achieve the total storage for the NVR server

od239818/2024_2025 : Supply, Installation, Testing ; Commissioning of 55 inch full HD LED monitor with resolution 1920X1080 pixel including wall mounting accessories

od239823/2024_2025 : Supply and installation of wall mounted 9 U rack including cable manager, power supply units etc.to accommodate ehternet switch and fiber patch panel at each floor

od239824/2024_2025 : Supply and installation of wall mounted 12 U rack including cable manager, power supply units etc.to accommodate ehternet switch and fiber patch panel at each floor

od239825/2024_2025 : Supply and installation of wall mounted 22U rack including cable manager, power supply units etc.to accommodate NVR, ethernet switch patch panel etc in control rooom

PUBLIC ADDRESS SYSTEM

od239766/2024_2025 : High Fidility 1.5/3/6W Ceiling Speakers with matching transformers, back boxes and accessories

od239771/2024_2025 : High Fidility 1.5/3/6W Wall-mounted Speakers with matching transformers, back boxes and accessories

od239774/2024_2025 : Supply and laying of Speaker Cable - 2core 24/0.2mm ATC twin twisted shielded, FRLS type, armoured cable (Green colour) to be drawn in existing surface/recessed steel/PVC conduit as required

od239780/2024_2025 : Supply, installation, testing and commissioning of Voice alarm Router to expand the Plena Voice Alarm System with six zones. EN 5416 certified.12 additional input contacts Six volume override output contacts. Supervision within the Plena Voice Alarm System Router.

od239794/2024_2025 : Supply, installation, testing and commissioning of Audio singnal Booster with all accesories as required.

od239800/2024_2025 : Supply, installation, testing and commissioning of Booster Amplifier 480 W

od239802/2024_2025 : Supply, installation, testing and commissioning of DVD player for background Music

TV SYSTEM

1.19 : Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

1.24.7 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.TV antenna socket outlet

od239775/2024_2025 : Cable TV connection from operator which includes supply, installation, testing and commissioning of all accessories (including the set top box, antenna, amplifier whichever is required) for making the cable TV connection to the Television point

od239784/2024_2025 : Supply, Installation, Testing and Commissioning of 40 inch LED SMART TV with necessary supports/stands etc. complete.

od239788/2024_2025 : Supply, Installation, Testing and Commissioning of 32 inch LED SMART TV with necessary supports/stands etc. complete.

ACCESS CONTROL SYSTEM

od239764/2024_2025 : Supply, installation, testing ; commissioning of 1 Class Reader (Bluetooth Enabled) with 2.5mm thick SS front plate as per specification suitable for mounting on metal surface/metal frames or wooden frames wall or as required based on site conditions including all accessories.

od239768/2024_2025 : Supply installation testing and commissioning of Proximity card readers

od239772/2024_2025 : Supply of smart cards for the access.

od239783/2024_2025 : Supply, Installation, Testing and Commssioining of 4 reader controller, power supply unit, TCP IP connectivity with tamper detection provision ,relay outputs,Tema Access Remote Terminal unit .Cost shall inclusive of enclosure and power supply unit for controller (power supply unit shall inclusive of battery backup).

od239786/2024_2025 : Supply, Installation, Testing and Commssioining of Electromagnetic Lock with required mounting brackets for single door / double door as per the tender specifications

od239795/2024_2025 : Supply, Installation, Testing and Commssioining of surface / flush mounted (as required at site) Magnetic Contact (Door position sensor) for access controlled doors as per the tender specifications

od239798/2024_2025 : Supply, Installation, Testing and Commssioining of Push Button/switch with accessories

od239805/2024_2025 : Supply installation, testing, commissioning of EDR (EMERGENCY BREAK GLASS )

od239806/2024_2025 :Supply and laying of 4 core 1.0 Sq mm Un Armoured Shielded FRLS, Multistanded Copper Conductor, PVC sheathed Cable for connecting controller to Lock ; door position sensors, Buzzer,BGU,Pushbutton as per the tender specificationsRate shall inclusive of 2mm thick suitable dia FRLS PVC conduits with ,JBs in wall, columns, ceiling etc., including associated civil works. (conduits ; cables - blue color)

od239813/2024_2025 : Supply and laying of 6 core x 1 Sq mm Un Armoured Shielded FRLS, Multistanded Copper Conductor, PVC sheathed Cable for connecting controller to readers as per the tender specifications Rate shall inclusive of 2mm thick suitable dia FRLS PVC conduits with ,JBs in wall, columns, ceiling etc., including associated civil works. (conduits ; cables - blue color)

od239814/2024_2025 :Supply and laying of 2 core x 1 Sq mm Un Armoured Shielded FRLS, Multistanded Copper Conductor, PVC sheathed Cable Rate shall inclusive of 2mm thick suitable dia FRLS PVC conduits with ,JBs in wall, columns, ceiling etc., including associated civil works. (conduits ; cables - blue color)

NURSE CALL SYSTEM

od239762/2024_2025 : SITC of nurse call system including the software, nurse station display unit,Bedside call/reset unit,toilet pull cord, door indication lamp etc for and as required to make the system complete and operational in all respects - Second Floor -(SICU(6 bed), Post OT(6bed), Pre OT (6bed))

od239767/2024_2025 : SITC of nurse call system including the software, nurse station display unit,Bedside call/reset unit,toilet pull cord, door indication lamp etc for and as required to make the system complete and operational in all respects - Third Floor -MICU(8 bed)

od239778/2024_2025 : SITC of nurse call system including the software, nurse station display unit,Bedside call/reset unit,toilet pull cord, door indication lamp etc for and as required to make the system complete and operational in all respects - (7th and 8th Floor-Pay wards(19 rooms in each floor))

FIRE FIGHTING SERVICE WORKS - FIRE PUMP ROOM EQUIPMENT

od235768/2024_2025 : Supplying, erecting, testing and commissioning FIRE HYDRANT PUMPS DRIVEN BY ELECTRIC MOTOR as per the following: : a) Centrifugal fire hydrant pump of 2280 LPM, @ 100 M Head (10 Kg/Cm2) pressure capacity along with horizontal split cast iron casing type, bronze impeller, SS 410 Shaft, mechanical seal foundation bolts / Anti vibration pads, and accessories as specified and directed. b) Electric TEFC Motor of suitable HP, 2900 rpm, 415 V, 3phase, 50 Hz AC, DOL starter including a terminal box for cable entry, size gland and termination, common bed plate and foundation bolts etc complete all as specified and directed.

od235769/2024_2025 : Supplying, erecting, testing and commissioning FIRE HYDRANT PUMPS DRIVEN BY DIESEL ENGINE as per the following: : a) Centrifugal fire hydrant pump of 2280 LPM, @ 100 M Head (10 Kg/Cm2) pressure capacity along with horizontal split cast iron casing type, bronze impeller, SS 410 Shaft, mechanical seal all as per specified and directed. b) Suitable HP, 1500 RPM automatic diesel engine driven pumpset ,DOL starter, along with residential silencer system,exhaust pipe with insulation ; cladding,exhaust pipe upto outside of building, fuel tank, necessary cooling system, with OS ; Y valve, NRV, Y stainer foundation bolts / Anti vibration pads, Pressure Guage, Pressure switch, test valve, day oil storage tank, two separate starting mechanism (automatic starting by battery power electric starting motor as well as manual starting motor all as per the specified and directed.

od235770/2024_2025 : Supply, erection, testing and commissioning of vertical inline 180 LPM, @ 100 M Head (10 Kg/Cm2) pressure capacity Centrifugal Jockey pump coupled with suitable eletrical driven motor, necessary foundtion bolts,and accessories, connections etc. Complete all as specified and directed by Engineer incharge.

od235771/2024_2025 : Supplying, installing, testing and commissioning of double flanged Rubber Expansion Bellows/ joint of standard length as per manufacturers specs including rubber PTFE / Asbestos free gaskets, flanges, nuts, bolts and washers complete as required. (Suction and Discharge side PN16) 150mm nominal diameter

od235772/2024_2025 : Providing and fixing of exhaust pipe M.S. Medium grade for Diesel engine shall not be smaller in diameter than engine exhaust outlet extended outside pump house, duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, flexible exhaust connection, residential silencer, instruments and protection as per specification NFPA 20 ,2016 with stand ; gauge glass, painting, rain cap and necessary supports as required.

od235774/2024_2025 : 1100 V GRADE POWER / CONTROL CABLES Supplying, laying, testing ; commissioning of suitable FRLS,PVC outer sheathe, steel armored, aluminum / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The minimum size of the cables shall as mentioned below, 3.5C x 120 sq.mm aluminum for main pumps

od235775/2024_2025 : 1100 V GRADE POWER / CONTROL CABLES Supplying, laying, testing ; commissioning of suitable FRLS,PVC outer sheathe, steel armored, aluminum / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The minimum size of the cables shall as mentioned below, 4 C x 16 Sqmm. Aluminum Jockey pump

od235776/2024_2025 : 1100 V GRADE POWER / CONTROL CABLES Supplying, laying, testing ; commissioning of suitable FRLS,PVC outer sheathe, steel armored, aluminum / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The minimum size of the cables shall as mentioned below, 12 C x 2.5 Sqmm. copper Diesel engines

od235777/2024_2025 : 1100 V GRADE POWER / CONTROL CABLES Supplying, laying, testing ; commissioning of suitable FRLS,PVC outer sheathe, steel armored, aluminum / copper conductor, 1100v grade power cables with glands etc. The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth. The minimum size of the cables shall as mentioned below, 2 C x 2.5 Sqmm. copper for instrumentation

od235778/2024_2025 : Supply and laying of 8 SWG copper wire through ceiling / walls, from the equipment to the nearest Earth pit/Earth bus with necessary accessories as required. (Earth pit shall be executed by other agencies).

od235779/2024_2025 : Providing and fixing 25mm x 3mm copper strip on surface or in recess for connections etc as required.

CABLE TRAY

4.9.2 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray ?Cross member? ( galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required.150 mm width X 50 mm depth X 1.6 mm thickness

4.9.3 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray ?Cross member? ( galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required.225 mm width X 50 mm depth X 1.6 mm thickness

FIRE PIPING SYSTEM

od236025/2024_2025 : Providing of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between ; fire sealent compound at either end all as per Project Manager&rsquo;s / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwise and then supply of the same shall also be included for rates under this head.. i) Cutting,welding / flanged joints with necessary washers, nuts, bolts etc ii) Concrete anchor blocks at all change in direction of pipeline and also near each joints iii) Necessary masonry supports wherever required-200 mm dia.

od236026/2024_2025 : Providing of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between ; fire sealent compound at either end all as per Project Manager&rsquo;s / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwise and then supply of the same shall also be included for rates under this head.. i) Cutting,welding / flanged joints with necessary washers, nuts, bolts etc ii) Concrete anchor blocks at all change in direction of pipeline and also near each joints iii) Necessary masonry supports wherever required-150 mm dia.

od236027/2024_2025 : Providing of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between ; fire sealent compound at either end all as per Project Manager&rsquo;s / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwise and then supply of the same shall also be included for rates under this head.. i) Cutting,welding / flanged joints with necessary washers, nuts, bolts etc ii) Concrete anchor blocks at all change in direction of pipeline and also near each joints iii) Necessary masonry supports wherever required-100 mm dia

od236028/2024_2025 : Providing of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between ; fire sealent compound at either end all as per Project Manager&rsquo;s / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwise and then supply of the same shall also be included for rates under this head.. i) Cutting,welding / flanged joints with necessary washers, nuts, bolts etc ii) Concrete anchor blocks at all change in direction of pipeline and also near each joints iii) Necessary masonry supports wherever required- 80 mm dia

od236066/2024_2025 : Providing of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between ; fire sealent compound at either end all as per Project Manager&rsquo;s / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwire and then supply of the same shall also be included for rates under this head-250 mm dia.

od236067/2024_2025 : Providing of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between ; fire sealent compound at either end all as per Project Manager&rsquo;s / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwire and then supply of the same shall also be included for rates under this head-200 mm dia

od236068/2024_2025 : Providing of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between ; fire sealent compound at either end all as per Project Manager&rsquo;s / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwire and then supply of the same shall also be included for rates under this head-150 mm dia

od236069/2024_2025 : Providing of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between ; fire sealent compound at either end all as per Project Manager&rsquo;s / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwire and then supply of the same shall also be included for rates under this head-100 mm dia

od236070/2024_2025 : Providing of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between ; fire sealent compound at either end all as per Project Manager&rsquo;s / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwire and then supply of the same shall also be included for rates under this head- 80 mm dia.

od236071/2024_2025 : Providing of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between ; fire sealent compound at either end all as per Project Manager&rsquo;s / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwire and then supply of the same shall also be included for rates under this head-40 mm dia.

od236072/2024_2025 : Providing of following sizes of GI C class pipes conforming to IS-1239 with all accessories like all fittings (standard GI fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. MS pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between ; fire sealent compound at either end all as per Project Manager&rsquo;s / Consultants.All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwire and then supply of the same shall also be included for rates under this head- 25 mm dia.

od238624/2024_2025 : Supply, fixing, testing and commissioning of following dia butterfly valves (PN 16) with insitu moulded seat of first quality, approved brand, confirming to relavent IS including vertical / horizontal gear unit with hand wheel, companion flanges, nuts, gaskets, bolts, etc. Complete all as specified and directed by Engineer incharge- 200 mm dia

od237979/2024_2025 : Supply, fixing, testing and commissioning of following dia butterfly valves (PN 16) with insitu moulded seat of first quality, approved brand, confirming to relavent IS including vertical / horizontal gear unit with hand wheel, companion flanges, nuts, gaskets, bolts, etc. Complete all as specified and directed by Engineer incharge-150 mm dia.

od237980/2024_2025 : Supply, fixing, testing and commissioning of following dia butterfly valves (PN 16) with insitu moulded seat of first quality, approved brand, confirming to relavent IS including vertical / horizontal gear unit with hand wheel, companion flanges, nuts, gaskets, bolts, etc. Complete all as specified and directed by Engineer incharge-100 mm dia

od237981/2024_2025 : Supply, fixing, testing and commissioning of following dia butterfly valves (PN 16) with insitu moulded seat of first quality, approved brand, confirming to relavent IS including vertical / horizontal gear unit with hand wheel, companion flanges, nuts, gaskets, bolts, etc. Complete all as specified and directed by Engineer incharge-80 mm dia

od237982/2024_2025 : Supply, fixing, testing and commissioning of following dia butterfly valves (PN 16) with insitu moulded seat of first quality, approved brand, confirming to relavent IS including vertical / horizontal gear unit with hand wheel, companion flanges, nuts, gaskets, bolts, etc. Complete all as specified and directed by Engineer incharge-65 mm dia

od237983/2024_2025 : Supply, fixing, testing and commissioning of following dia butterfly valves (PN 16) with insitu moulded seat of first quality, approved brand, confirming to relavent IS including vertical / horizontal gear unit with hand wheel, companion flanges, nuts, gaskets, bolts, etc. Complete all as specified and directed by Engineer incharge-50 mm dia

od236208/2024_2025 : Supplying, installing, testing and commissioning of C.I. Non-return valves as per IS:5312( PN 16) swing check type with required flanges, nuts, bolts 15mm thick compressed asbestos gasket including matching flanges complete ,GI bolts, nuts, washers etc.as required-200 mm nominal diameter

od236209/2024_2025 : Supplying, installing, testing and commissioning of C.I. Non-return valves as per IS:5312( PN 16) swing check type with required flanges, nuts, bolts 15mm thick compressed asbestos gasket including matching flanges complete ,GI bolts, nuts, washers etc.as required-150 mm nominal diameter

od236210/2024_2025 : Supplying, installing, testing and commissioning of C.I. Non-return valves as per IS:5312( PN 16) swing check type with required flanges, nuts, bolts 15mm thick compressed asbestos gasket including matching flanges complete ,GI bolts, nuts, washers etc.as required-100 mm nominal diameter

od236211/2024_2025 : Supplying, installing, testing and commissioning of C.I. Non-return valves as per IS:5312( PN 16) swing check type with required flanges, nuts, bolts 15mm thick compressed asbestos gasket including matching flanges complete ,GI bolts, nuts, washers etc.as required-80 mm nominal diameter

od236212/2024_2025 : Supplying, installing, testing and commissioning of C.I. Non-return valves as per IS:5312( PN 16) swing check type with required flanges, nuts, bolts 15mm thick compressed asbestos gasket including matching flanges complete ,GI bolts, nuts, washers etc.as required-50 mm nominal diameter

od236226/2024_2025 : Supply, Fixing, Testing and commissioning of double flanged sluice valve of rating PN 16 as per IS:780 with non rising spindle type, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and confirming to IS 780 of following size -150 mm nominal diameter

od236227/2024_2025 : Supply, Fixing, Testing and commissioning of double flanged sluice valve of rating PN 16 as per IS:780 with non rising spindle type, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and confirming to IS 780 of following size-100 mm nominal diameter

od236228/2024_2025 : Supply, Fixing, Testing and commissioning of double flanged sluice valve of rating PN 16 as per IS:780 with non rising spindle type, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and confirming to IS 780 of following size -80 mm nominal diameter

od236229/2024_2025 : Supply, Fixing, Testing and commissioning of double flanged sluice valve of rating PN 16 as per IS:780 with non rising spindle type, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and confirming to IS 780 of following size -50 mm nominal diameter

od236230/2024_2025 : Supply, Fixing, Testing and commissioning of double flanged sluice valve of rating PN 16 as per IS:780 with non rising spindle type, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and confirming to IS 780 of following size -200 mm nominal diameter

od236256/2024_2025 : Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valve with fittings of screwed end type-25 mm diameter

od236257/2024_2025 : Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valve with fittings of screwed end type-40 mm diameter

od236258/2024_2025 : Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valve with fittings of screwed end type-15 mm diameter

od236299/2024_2025 : supply installation of UL listed pressure gauge 1/4 BSPT, minimum 3.5 dial of suitable range to be installed in pump room suction, discharge, diesel pump and Sprinkler ; Standpipe Systems. Dial type White background black graduation scale with dual reading in Kg./ Sq.cm and PSI complete as required.

od236300/2024_2025 : Providing ; fixing heavy forged brass tested ISI marked 2280 Lpm Flow Pressure Relief valves (16 Bar) of approved quality with all necessary Piping connections till the Bypass valve to Water Tank (To be installed in diesel pump Header in Pump Room)

od236301/2024_2025 : Supply, fixing, testing and commissioning of Providing, fixing, testing ; commissioning of Zone control valve of cast iron body,brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required.

od236302/2024_2025 : Supply, fixing, testing and commissioning of the SINGLE HEADED YARD HYDRANT (EXTERNAL) of first quality, approved brand, confirming to relavent IS composed of the following :-a) 80 mm dia GIF bend. b) 80 mm dia GIF stand pipe (1 Mtr above). c) 63 mm dia female instantenous pattern oblique hydrant valve chain and cap of Gun metal. The pipe portion below ground shall be painted with 3mm thick bituminous coat and pipe exposed outside shall be painted with 2 coats of synthetic enamel paint over a coat of primer. etc Complete all as specified and directed by Engineer incharge.

od236303/2024_2025 : Supply, fixing, testing and commissioning of the SINGLE HEADED YARD HYDRANT( INTERNAL ) with inbuilt PRV of first quality, approved brand, confirming to relavent IS composed of the following :-a) 80 mm dia GIF bend. b) 80 mm dia GIF stand pipe (1 Mtr above). c) 63 mm dia female instantenous pattern oblique hydrant valve chain and cap of Gun metal. The pipe shall be painted with 2 coats of synthetic enamel paint over a coat of primer. etc Complete all as specified and directed by Engineer incharge.

od236315/2024_2025 : Supply and fix external glass fronted hose cabinet glass fronted with hinged and lock, made out of 16 G M.S. sheet of suitable size with (3mm thick glass with rubber beeding) door and size of the cabinet shall be 750 mm x 600 mm x 250 mm powder coated paint complete all as specified and directed by Engineer incharge. With a) 2 lengths of 15 M long, 63mm dia RRL hose with instataneuos couplings and Hoses shall be stored in side the hose cabinet.b) Branch pipe ; nozzle (one set). c) Two keys of Recess type for break glass.

od236316/2024_2025 : Supplying and fixing 63 mm diameter, 15 m long RRL hose pipe with 63 mm diameter male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required.

od236317/2024_2025 : Supplying ; fixing 63 mm diameter gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

od236318/2024_2025 : Supply, installation, testing and commissioning of Y-Strainer PN-16 rating. Body: Cast Iron with Powder coating, Stainless Steel filter screen/mesh. The cost shall be inclusive of mating flanges of appropriate class, Asbestos free gasket, washers, nut and bolts etc. complete. 150mm dia.

od236319/2024_2025 : Supply, installation, testing and commissioning of Y-Strainer PN-16 rating. Body: Cast Iron with Powder coating, Stainless Steel filter screen/mesh. The cost shall be inclusive of mating flanges of appropriate class, Asbestos free gasket, washers, nut and bolts etc. complete. 100mm dia.

od236332/2024_2025 : Supplying, installing, testing and commissioning conventional Sprinkler quartzoid bulb type with 15mm screwed end connection of 68 deg. C. temperature rating,K 80 and orifice shall not be less than 6mm.Sprinklers shall be FM approved with Chrome finished- Pendent sprinkler

od236333/2024_2025 : Supplying, installing, testing and commissioning conventional Sprinkler quartzoid bulb type with 15mm screwed end connection of 68 deg. C. temperature rating,K 80 and orifice shall not be less than 6mm.Sprinklers shall be FM approved with Chrome finished- Upright

od236334/2024_2025 : Supplying, installing, testing and commissioning conventional Sprinkler quartzoid bulb type with 15mm screwed end connection of 68 deg. C. temperature rating,K 80 and orifice shall not be less than 6mm.Sprinklers shall be FM approved with Chrome finished-Side wall

od236335/2024_2025 : Supply, installation, testing ; commissioning of SS 25 mm dia Flexible braided hose suitable for sprinkler system, UL/ FM approved with all necessary fittings ; accessories, etc complete. Rate quoted shall also include for necessary clamps,/ fixing system for the braided hose.sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required-1 m length

od236336/2024_2025 : Supply, installation, testing ; commissioning of SS 25 mm dia Flexible braided hose suitable for sprinkler system, UL/ FM approved with all necessary fittings ; accessories, etc complete. Rate quoted shall also include for necessary clamps,/ fixing system for the braided hose.sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required-1.2 m length

od236337/2024_2025 : Supply, installation, testing ; commissioning of SS 25 mm dia Flexible braided hose suitable for sprinkler system, UL/ FM approved with all necessary fittings ; accessories, etc complete. Rate quoted shall also include for necessary clamps,/ fixing system for the braided hose.sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required-1.5 m length

od236349/2024_2025 : Supply, fixing, testing and commissioning of sight unit with bypass unit, flow switch, union, flange joint, Drain valve, Test valve,ball valve 50 mm dia, 50 mm dia interconnecting pipe, all of approved brand of manufacture. Flow swich connection shall be as per NBC PART - IV ( indicated in NBC)-150 mm dia.

od236350/2024_2025 : Supply, fixing, testing and commissioning of sight unit with bypass unit, flow switch, union, flange joint, Drain valve, Test valve,ball valve 50 mm dia, 50 mm dia interconnecting pipe, all of approved brand of manufacture. Flow swich connection shall be as per NBC PART - IV ( indicated in NBC)- 100mm dia

od236351/2024_2025 : Supply, fixing, testing and commissioning of sight unit with bypass unit, flow switch, union, flange joint, Drain valve, Test valve,ball valve 50 mm dia, 50 mm dia interconnecting pipe, all of approved brand of manufacture. Flow swich connection shall be as per NBC PART - IV ( indicated in NBC)-80mm dia

od236352/2024_2025 : Supply, fixing, testing and commissioning of Test connection with 25mm dia GM ball valve Complete all as specified and directed by Engineer in charge.

od236353/2024_2025 : Supply, installation, testing ; commissioning of sight galss unit of dia 25mm for test connection with all necessary fittings and accessories etc.,complete

od236354/2024_2025 : Supply, installation, testing ; commissioning of 150mm dia pressure gauge ( Glyserine Filled), siphon and cock burden type suitable for required pressure dial to be graduated both on PSI and Kg/Cm2 with all necessary jointing materials and fittings etc., complete

od236355/2024_2025 : Providing ; fixing of pressure switch in pipe line including connection etc. as required

od236356/2024_2025 : Providing ; fixing of flow switch on sprinkler distribution header on each floor and shall be connected to fire alarm panel through cable. Cable shall be measured separately, following sizes of fire pipe including connection etc. as required. 100mm diameter

od236357/2024_2025 : Providing ; fixing of flow switch on sprinkler distribution header on each floor and shall be connected to fire alarm panel through cable. Cable shall be measured separately, following sizes of fire pipe including connection etc. as required. 150mm diameter

od236358/2024_2025 : Providing, installation, testing ; commissioning of adjustable rosette plate for 15mm diameter, fabricated by M.S. plate of 2mm thick and the finish shall be powder coated in white finish UL Listed or FM approved complete as required.

od237655/2024_2025 : Providing, Laying. Testing ; Commissioning of 450 mm dia RCC pipes of NP2 class with suitable collars filling the recess at joints of pipes with hemp dipped in hot bitumen or other suitable compound for chaulking of joint by jack, setting up of loose space over the collar joints chaulked with CM 1:2, finished both ends to a slope of 1:1 including curing, testing of pipes, etc., Complete all as specified and directed by Engineer in charge. Note: Earth work will be measured under relevent Items

ANALOGUE ADDRESSABLE FIRE ALARM ; DETECTION SYSTEM

od236365/2024_2025 : Cost for addition / deletion of extra Loop cards in to the panel mentioned above.

od236366/2024_2025 : Supplying, installation, testing ; commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

od236367/2024_2025 : Supplying, installation, testing ; commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required. (Suitable for both above and below false ceiling)

od236368/2024_2025 : Supplying, installation, testing ; commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

od236369/2024_2025 : Supplying, installation, testing ; commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

od236370/2024_2025 : Supplying, installation, testing ; commissioning of intelligent addressable duct detector including suitable Photo detector complete with base as required.

od236371/2024_2025 : Supplying, installation, testing ; commissioning of fault isolator module complete with base as required.

od236372/2024_2025 : Supplying, installation, testing ; commissioning of addressable fire control module complete as required.

od236373/2024_2025 : Analogue Addressable Monitor module for monitoring the field devices ; shall be capable of providing DPDTcontact rated at 24v DC, 2A. ( for flow switches)

od236374/2024_2025 : Analogue Addressable Control relay module for AHU tripping and shall be capable of providing DPDTcontact rated at 24v DC, 2A.

od236375/2024_2025 : Supplying, installation, testing ; commissioning of addressable horn cum strobe complete as required.

od236376/2024_2025 : Supplying, installation, testing ; commissioning of addressable manual call point with break glass type complete as required.

od236377/2024_2025 : Supplying ; laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring ; FRLS outer sheath complete as required.

od236378/2024_2025 : Supplying and fixing 25 mm dia MS flexible pipe with PVC (conduit) coating along with all ancillaries and accessories like coupler etc. as required. 25 mm dia. (for laying cables on stairs wall)

TWOWAY TALK BACK SYSTEM

od236942/2024_2025 : Supplying, installation, testing ; commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required. Panel should be with CRCA sheet housing, control desk( rack) and suitable rack for mounting amplifier ; console as required. Console shall have all call / call back facility complete with battery back up and it should also work on AC single phase power. PA console, amplifier and all associate accessories shall be installed in metal sheet fabricated cabinet.

od236943/2024_2025 : Supplying, installation, testing ; commissioning of Voice command keypad 6 zone, (two way talk back system for staircases) with microphone assembly complete as required.

od236944/2024_2025 : Supplying, installing, testing and commissioning solid state Amplifier of 480 W RMS out put in rack, including necessory control wires, jocks etc. complete.

od236945/2024_2025 : Supplying, installation, testing ; commissioning of 6/10W metal box ceiling/wall speakers complete as required.

od236946/2024_2025 : Supplying, installation, testing ; commissioning of 6/10W ceiling speaker complete as required.

od236948/2024_2025 : Supply and fixing of Talk back speaker unit 5W LMT, Press to talk switch MS housing with Red color.

od236949/2024_2025 : Supplying ; laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring ; FRLS outer sheath complete as required.

FIRE EXTINGUISHERS

od237000/2024_2025 :FIRE EXTINGUISHERS - FIRST AID :Supply and install in position approved make Dry Chemical Powder Fire Extinguisher 5/6 Kgs capacity (ABC Type) complete with chromium plated gun metal union (cap), fitted with braided hose and open nozzle with initial charge of Dry Chemical Powder and gas cartridge complete with bracket and fixing screws. The extinguisher is internally and externally coated with lead tin alloy through hot dip process and cylinder bearing No. IS:15683 and the gas cartridge bearing with ISI certitifcation mark. Complete all as specified and directed by Engineer in charge.

od237001/2024_2025 : Supply and install in position approved make Water Co2 Fire Extinguisher of 9 Ltrs capacity of conical shape fitted with chromium plated gun metal nozzle on the top end of the fire extinguisher for discharge of liquid and chromium plated gun metal union (Cap) at the bottom with angle fixed in the centre, complete with bracket, fixing screws, spanner and one filling. The extinguisher is internally and externally coated with lead, tin alloy through hot-dip process and bearing IS:15683 with ISI certification mark. Complete all as specified and directed by Engineer in charge.

od237002/2024_2025 : Supply and install in position approved make carbon-di-oxide 4.5 Kgs capacity fire extinguisher, made of high pressure with wheel type valve with one metre long braided high pressure discharge hose which should have a minimum of bursting pressure of 14.0 N/Sqmm and fitted with ABS discharge born and handles (non-conductor), complete with bracket and steel handle on the body fully charged with ISI certification. mark, ISI:2878/1976. Complete all as specified and directed by Engineer in charge.

od237003/2024_2025 : Supply installation of 2 Nos.Fire buckets filled with sand round bottom type enamel painted, white inside ; Red out side and LetterFIRE in black out side and handle with mounting bracket as per the tender drawing. Along with Fabrication supply and installation of Fire bucket stand fabricated by MS angles/pipes to install 2 Nos. of buckets. Complete all as specified and directed by Engineer in charge.

od237004/2024_2025 : Supply and install in position approved make AFFF Mechanical Foam Fire Extinguisher, 9 Ltrs capacity fitted with chromium plated gun metal cap, plastic coated gas cartridge fitted with braided hose and foam branch complete with brackets and initial charge of Aqueous film forming liquid of 6% concentration as per IS:10204.

od237005/2024_2025 : Supply and install in position approvedmake AFFF Mechanical Foam Fire Extinguisher, 50 Ltrs capacity fitted with chromium plated gun metal cap, plastic coated gas cartridge fitted with braided hose and foam branch complete with brackets and initial charge of Aqueous film forming liquid of 6% concentration as per IS:10204.

od237006/2024_2025 : Supply and install in position approved make Dry Chemical Powder Fire Extinguisher 10 Kgs capacity (ABC Type) complete with chromium plated gun metal union (cap), fitted with braided hose and open nozzle with initial charge of Dry Chemical Powder and gas cartridge complete with bracket and fixing screws. The extinguisher is internally and externally coated with lead tin alloy through hot dip process and cylinder bearing No. IS:15683 and the gas cartridge bearing with ISI certitifcation mark. Complete all as specified and directed by Engineer in charge.

FIRE SIGNAGES

od237058/2024_2025 : Providing and installing in position the following type of sign board made out of 3mm thick &ldquo;opaque PVC foam board with computer cut, design, letters letters on both side with instructed letter dimensions and colour etc., PVC non-reflective vinyl painted foam board, complete with hanging chain/wall hangings, signage with required printed, Complete all as specified and directed by Engineer in charge.The size of the board shall be as follow and shall be fixed at any floor height-200mmx250mm

od237059/2024_2025 : Providing and installing in position the following type of sign board made out of 3mm thick &ldquo;opaque PVC foam board with computer cut, design, letters letters on both side with instructed letter dimensions and colour etc., PVC non-reflective vinyl painted foam board, complete with hanging chain/wall hangings, signage with required printed, Complete all as specified and directed by Engineer in charge.The size of the board shall be as follow and shall be fixed at any floor height-150mmx500mm

od237060/2024_2025 : Providing and installing in position the following type of sign board made out of 3mm thick &ldquo;opaque PVC foam board with computer cut, design, letters on both side with instructed letter dimensions and colour etc., PVC reflective vinyl painted foam board, complete with hanging chain, signage with required printed, Complete all as specified and directed by Engineer in charge.The size of the board shall be as follow and shall be fixed at any floor height-150mmx500mm

od237140/2024_2025 : Providing and installing in position the following type of sign board made out of 3mm thick &ldquo;opaque PVC foam board with computer cut, design, letters on both side with instructed letter dimensions and colour etc., PVC reflective vinyl painted foam board, complete with hanging chain, signage with required printed, Complete all as specified and directed by Engineer in charge.The size of the board shall be as follow and shall be fixed at any floor height-600mmx750mm

od237061/2024_2025 : Fire Exit signage Dual Side above the door of each stair enclosure on every floor, indicating the direction of exit in case of fire emergency, lettering size shall be 5 cm with contrasting colour from back ground.Size shall be 6 x 12. Complete all as specified and directed by Engineer in charge.

od237062/2024_2025 : Fire Exit signage Single Side above the door of each stair enclosure on every floor, indicating the direction of exit in case of fire emergency, lettering size shall be 5 cm with contrasting colour from back ground.Size shall be 6 x 12. Complete all as specified and directed by Engineer in charge.

HVAC SERVICE WORKS - VRF/VRV INDOOR AND OUTDOOR UNITS

od239735/2024_2025 : VRF Indoor Units :Ductable Unit :-Supply, installation, testing and commissioning of following minimum capacity and suitable external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc. suitable for operation on single phase AC supply 230V&plusmn;10%,50Hz complete as required.(VRF) 2 TR - 720 cfm

od239736/2024_2025 : VRF Indoor Units :Ductable Unit :-Supply, installation, testing and commissioning of following minimum capacity and suitable external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc. suitable for operation on single phase AC supply 230V&plusmn;10%,50Hz complete as required.(VRF) 2.5 TR - 900 cfm

od239737/2024_2025 : VRF Indoor Units :Ductable Unit :-Supply, installation, testing and commissioning of following minimum capacity and suitable external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc. suitable for operation on single phase AC supply 230V&plusmn;10%,50Hz complete as required.(VRF) 3 TR - 1100 cfm

od239738/2024_2025 : VRF Indoor Units ::Ductable Unit :-Supply, installation, testing and commissioning of following minimum capacity and suitable external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc. suitable for operation on single phase AC supply 230V&plusmn;10%,50Hz complete as required.(VRF) 5.5 TR - 2000 cfm

od239739/2024_2025 : VRF Indoor Units ::Ductable Unit :-Supply, installation, testing and commissioning of following minimum capacity and suitable external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc. suitable for operation on single phase AC supply 230V&plusmn;10%,50Hz complete as required.(VRF) 6 TR - 2250 cfm

od239745/2024_2025 : Supply installation testing and commissioning of following minimum capacity high wall units with multilevel filter for better air quality, auto restart and multimode. (VRF).2.0 TR/ 720CFM

od239746/2024_2025 : Supply installation testing and commissioning of following minimum capacity high wall units with multilevel filter for better air quality, auto restart and multimode. (VRF).1.5 TR/ 540 CFM

od239747/2024_2025 : Supply installation testing and commissioning of following minimum capacity high wall units with multilevel filter for better air quality, auto restart and multimode. (VRF).1.0 TR/360 CFM

od239753/2024_2025 : S.I.T.C. of Cabinet type Double skin (43 mm insulation with thermal break profile) Floor mounted TFA with direct driven plug fans AHRI/ Eurovent certified complete with pre filter, DX cooling coil, Backward curved fan, motor and drive package for fan, canvass at unit outlet, outlet damper, vibration isolators. Outlet Velocity of the fan to be restricted to 9.5 m/s, necessary vibration isolation arrangement etc.Wiring of 20Rmt from starter panel to TFA for Electrical interlock for access door and marine light to be included. complete as per specification and of following capacities of TFA- 6TR / 1200 CFM, ESP - 60 MM - for all floor fresh air

VRF/VRV AIR HANDLING UNIT

FRESH AIR/ EXHAUST FANS

od239026/2024_2025 : WALL MOUNTED PROPELLER TYPE FAN The supply installation of wall mountable propeller type inline fan with all accessories like fan, motor, mounting frame, cowl duct piece, protection guarads,etc.,. The motor should be of IP21, class B insulation suitable for operating at 3 phase, 230V, 50hz power supply. 1000 CFM / 2mm Static GF Electrical substation

od239035/2024_2025 : WALL MOUNTED PROPELLER TYPE FAN The supply installation of wall mountable propeller type inline fan with all accessories like fan, motor, mounting frame, cowl duct piece, protection guarads,etc.,. The motor should be of IP21, class B insulation suitable for operating at 3 phase, 230V, 50hz power supply. 100 CFM / 2mm Static

od239045/2024_2025 : WALL MOUNTED PROPELLER TYPE FAN :- The supply installation of wall mountable propeller type inline fan with all accessories like fan, motor, mounting frame, cowl duct piece, protection guarads,etc.,. The motor should be of IP21, class B insulation suitable for operating at 3 phase, 230V, 50hz power supply. 200 CFM / 10mm Static

od239047/2024_2025 : WALL MOUNTED PROPELLER TYPE FAN :- The supply installation of wall mountable propeller type inline fan with all accessories like fan, motor, mounting frame, cowl duct piece, protection guarads,etc.,. The motor should be of IP21, class B insulation suitable for operating at 3 phase, 230V, 50hz power supply. 500 CFM / 10mm Static

od239053/2024_2025 : WALL MOUNTED PROPELLER TYPE FAN The supply installation of wall mountable propeller type inline fan with all accessories like fan, motor, mounting frame, cowl duct piece, protection guarads,etc.,. The motor should be of IP21, class B insulation suitable for operating at 3 phase, 230V, 50hz power supply. 650 CFM / 2mm Static GF

od239058/2024_2025 : WALL MOUNTED PROPELLER TYPE FAN The supply installation of wall mountable propeller type inline fan with all accessories like fan, motor, mounting frame, cowl duct piece, protection guarads,etc.,. The motor should be of IP21, class B insulation suitable for operating at 3 phase, 230V, 50hz power supply. 800 CFM / 2mm Static

od239059/2024_2025 : CIRCULAR MIXED FLOW INLINE FAN :-The supply installation of Circular mixed flow inline fan with all accessories like fan, motor, flanges, non-canvass type fire retardant flexible connections, etc., The impeller shall be of forward type. The motor should be of IP21, class B insulation suitable for operating at 1phase, 230V, 50hz power supply. 150 CFM / 25mm Static

od239062/2024_2025 : CIRCULAR MIXED FLOW INLINE FAN - The supply installation of Circular mixed flow inline fan with all accessories like fan, motor, flanges, non-canvass type fire retardant flexible connections, etc., The impeller shall be of forward type. The motor should be of IP21, class B insulation suitable for operating at 1phase, 230V, 50hz power supply. 200 CFM / 30mm Static

od239064/2024_2025 : CIRCULAR MIXED FLOW INLINE FAN :-The supply installation of Circular mixed flow inline fan with all accessories like fan, motor, flanges, non-canvass type fire retardant flexible connections, etc., The impeller shall be of forward type. The motor should be of IP21, class B insulation suitable for operating at 1phase, 230V, 50hz power supply. 300 CFM / 15mm Static

od239838/2024_2025 : WALL MOUNTED PROPELLER TYPE FAN :- The supply ; installation of wall mountable propeller type inline fan with all accessories like fan, motor, mounting frame, cowl duct piece, protection guarads,etc.,. The motor should be of IP21, class B insulation suitable for operating at 3 phase, 230V, 50hz power supply. 350 CFM / 10mm Static

od239067/2024_2025 : CIRCULAR MIXED FLOW INLINE FAN :-The supply installation of Circular mixed flow inline fan with all accessories like fan, motor, flanges, non-canvass type fire retardant flexible connections, etc., The impeller shall be of forward type. The motor should be of IP21, class B insulation suitable for operating at 1phase, 230V, 50hz power supply. 400 CFM / 50mm Static

od239070/2024_2025 : CIRCULAR MIXED FLOW INLINE FAN :-The supply installation of Circular mixed flow inline fan with all accessories like fan, motor, flanges, non-canvass type fire retardant flexible connections, etc., The impeller shall be of forward type. The motor should be of IP21, class B insulation suitable for operating at 1phase, 230V, 50hz power supply. 500 CFM / 20mm Static

od239072/2024_2025 : CIRCULAR MIXED FLOW INLINE FAN :-The supply installation of Circular mixed flow inline fan with all accessories like fan, motor, flanges, non-canvass type fire retardant flexible connections, etc., The impeller shall be of forward type. The motor should be of IP21, class B insulation suitable for operating at 1phase, 230V, 50hz power supply. 825 CFM / 25mm Static

od239074/2024_2025 : CIRCULAR MIXED FLOW INLINE EX.FAN:- The supply installation of Circular mixed flow inline exhaust fan with all accessories like fan, motor, flanges, non-canvass type fire retardant flexible connections, etc., The impeller shall be of forward type. The motor should be of IP21, class B insulation suitable for operating at 1phase, 230V, 50hz power supply. 1000 CFM / 25mm Static

od239076/2024_2025 : CIRCULAR MIXED FLOW INLINE FAN :-The supply installation of Circular mixed flow inline fan with all accessories like fan, motor, flanges, non-canvass type fire retardant flexible connections, etc., The impeller shall be of forward type. The motor should be of IP21, class B insulation suitable for operating at 1phase, 230V, 50hz power supply. 1600 CFM / 20mm Static

od239078/2024_2025 : CIRCULAR MIXED FLOW INLINE FAN :-The supply installation of Circular mixed flow inline fan with all accessories like fan, motor, flanges, non-canvass type fire retardant flexible connections, etc., The impeller shall be of forward type. The motor should be of IP21, class B insulation suitable for operating at 1phase, 230V, 50hz power supply. 2300 CFM / 40mm Static

od239079/2024_2025 : Inline type fan suitable for ducted OT area fumigation exhaust application consisting of GSS cabinet, fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level. Supply, installation, testing and commissioning of 450 cfm , TSP - 20 mm - For OT

od239084/2024_2025 : Inline type fan suitable for ducted fresh air application consisting of GSS cabinet, fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level.Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 400 cfm , TSP - 20 mm

od239086/2024_2025 : Inline type fan suitable for ducted fresh air application consisting of GSS cabinet, fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level.Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 450 cfm , TSP - 25 mm

od239088/2024_2025 : Inline type fan suitable for ducted fresh air application consisting of GSS cabinet, fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level.Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 600 cfm , TSP - 30 mm

od239090/2024_2025 : Inline type fan suitable for ducted fresh air application consisting of GSS cabinet, fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level.Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 650 cfm , TSP - 70 mm

od239094/2024_2025 : Inline type fan suitable for ducted fresh air application consisting of GSS cabinet, fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level.Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 900 cfm , TSP - 70 mm

od239098/2024_2025 : Inline type fan suitable for ducted fresh air application consisting of GSS cabinet, fan, access door, flanged inlet and outlet connection, thermally protected motor and low noise level.Fan efficiency should be minimum 60% to meet ECBC 2017 compliance. Supply, installation, testing and commissioning of 1100 cfm , TSP - 60 mm

LOW VALUE ITEMS

od239000/2024_2025 : Centralised microprocessor based controller capable of controlling the entire system from a central location. This shall facilitate ON / OFF, temperature setting, fan speed, swing state of the louvers, run time scheduling etc of all the indoor units. The controller shall detect and display the status and various operating parameters of the outdoor units and the indoor units. The controller shall be BMS compatible.

od239003/2024_2025 : SITC of ODU connecting Kit and panel as per OEM

od239004/2024_2025 : S.I.T.C of SS grade plenum of suitable size for the equipments consisting of mini pleat HEPA filter, collar, volume control damper and access to filter. The arrangement should be suitable to mount above the OT Table. The unit shall be provided with a perforated Aluminum sheet at the bottom for air discharge.

od239007/2024_2025 : TERMINAL HEPA FILTERS :- Supply, Installation, Testing ; Commissioning of laminar station and SS plenum as follow: Laminar flow diffuser essentially should consists in: A plenum, constituting the pressurization chamber, entirely constructed of 1mm-thick 304 stainless steel sheet, with smooth finish to prevent dust collection. Four/Six square flanges are mounted to connect the plenum to air distribution ducts. External stiffening ribs and anticondensation insulation. Supply air filter housing, 304 stainless steel frame with stainless steel fasteners. Filtering unit consisting of absolute filters with efficiency 99,995%. Classification: CEN EN 1822 - H14. Sealed, stainless steel central component for connection of the surgical lamp. Lower component should consists of 1mm-thick 304 stainless steel panels with conveniently sized slots to assure the requested flow. The special system allows the perforated panels to be locked in and fully opened for easy and safe servicing and replacing of filters. Stainless steel mounting frame, constructed so as to assure sealed connection to the suspended ceiling, and perfect separation from the controlled work area by means of synthetic rubber seals. Diffuser Size: 2400x1800MM

od239009/2024_2025 : Communication cable between indoor and outdoor units of 2Cx1.5 Sqmm Cu. Cable placed in a 3/4 conduit.

od239015/2024_2025 : Control cable of OEM recommended size between indoor and outdoor units of Dx type with necessary fixing arrangement.

od239018/2024_2025 : Supply laying and commissioning of 4Cx2.5 sqmm Copper armored power cable from Stabilizer to outdoor units

od239019/2024_2025 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape. 1) 1/4 dia (6.4 MM) with 13 mm insulation

od239025/2024_2025 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape. 2) 3/8 dia (9.5 MM) with 13 mm insulation

od239029/2024_2025 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape. 3) 1/2 dia (12.7 MM) with 13 mm insulation

od239032/2024_2025 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape. 4) 5/8 dia (15.9 MM ) with 13 mm insulation

od239036/2024_2025 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape. 5) 3/4 dia (19.1 MM ) with 13 mm insulation

od239046/2024_2025 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape. 6) 7/8 dia (22.4 MM) with 19 mm insulation

od239051/2024_2025 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape. 7) 1 dia (25.8 MM) with 19 mm insulation

od239052/2024_2025 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape.8) 1-1/4 dia (28.6 MM) with 19 mm insulation

od239055/2024_2025 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape. 9) 1-3/8 dia (34.9 MM) with 19 mm insulation

od239060/2024_2025 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape.10) 1-5/8 dia (38.1 MM) with 19 mm insulation

od239061/2024_2025 : SITC of Copper Refrigerant piping with 18G HD Copper pipes, insulated with specified thickness nitrile rubber tubings and joints sealed with black cotton tape. 10) 1-5/8 dia (41.3 MM) with 19 mm insulation

od239065/2024_2025 : Refnet joints of all required size of copper pipes as per manufacturer recommendation.

SUB HEAD 'C' DUCTING AND GRILLS

16.12.1.1 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006

16.12.1.2 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006

16.12.1.3 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular dueling as per IS 655-2006

16.12.1.4 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.factory fabricated GSS sheet metal rectangular dueling as per IS 655-2006

16.12.2.1 : Supply, Installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular / round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, etc as per approved drawings and specifications of following sheet thickness complete as required.Site fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 0.63 mm thick

16.12.2.2 : Supply, Installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular / round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, etc as per approved drawings and specifications of following sheet thickness complete as required.Site fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 0.8. mm thick

16.12.2.3 : Supply, Installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular / round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, etc as per approved drawings and specifications of following sheet thickness complete as required.Site fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 1.00 mm thick

16.12.2.4 : Supply, Installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular / round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, etc as per approved drawings and specifications of following sheet thickness complete as required.Site fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 1.25 mm thick

od239021/2024_2025 : Supply, installation, balancing and commissioning of factory fabricated Aluminium sheet metal rectangular/round ducting for OTs complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of Thickness 0.64(22G) mm sheet

od239023/2024_2025 : Factory fabricated double skin plenum of 25mm thick PUF panels of density 40 kg/cum, casing inside ; outside material - GI ; casing inside ; outside thickness - 0.6 mm . The area indicated is the surface area of the plenum.

od239027/2024_2025 : Supplying, fixing acoustic lining on wall and ceiling of AHU rooms with 50mm thick, density 32 kg/cu.m resin bonded glass fiber insulation friction fixed in 610mm x 610 mm frame work made of 25X50X50X50X25 mm made out of 0.6mm thick GI sheet U shaped channel and covered with reinforced fiber glass tissue and finished with 0.80 mm perforated aluminium sheet etc. complete as required and as per specifications.

16.21.1 : Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m3, with 25 mm X 25 mm Gl section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications. 16 <br> <br>Acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m3Acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m3

od239037/2024_2025 : Supplying and fixing 50mm thick aluminium foil faced resin bonded fibre glass insulation (on duct) of density 24 kg/cu.m or mineral wool insulation(non combustible) of density 44 kg/cum after applying two coats of cold setting adhesive (CPRX compound) sealing all joints with self adhesive aluminium tape ; covering with 0.63mmx19mm GI wire mesh netting ; butting all joints and laced with GI wire complete and finally covered with one layer of tar felt stuck with hot bitumen as per specifications and as required. (for outdoor applications)

od239041/2024_2025 : Supplying and fixing of following thickness closed cell Nitrile rubber (class &ldquo;O) insulation on duct after applying two coats of cold setting adhesive (CPRX compound). The all joints shall sealed cotton tape insulation complete as per specifications and 10 mm thk.

od239043/2024_2025 : Supplying and fixing of following thickness closed cell Nitrile rubber (class &ldquo;O) insulation on duct after applying two coats of cold setting adhesive (CPRX compound). The joints shall sealed cotton tape insulation complete as per specifications and 13 mm thk.

od239049/2024_2025 : Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class &ldquo;O) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.19 mmsqm

16.13 : Supply, Insulation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications. GI volume control duct damper

od239057/2024_2025 : Supply, installation, testing and commissioning of GSS Non return damper with frame and Blades neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

16.14.1 : Supply, Installation, testing and commissioning of motorized (ON-OFF Type) duct mounted GI volume control damper with enthalpy sensor and necessary control wire (minimum 1.5 sqmm) for integration within AHU roomMotorized (ON-OFF Type) duct mounted GI volume control damper

16.15 : Suppluying and Fixing of powder costed extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

od239066/2024_2025 : Supply, installation, testing ; commissioning of thermal insulated flexible duct of following sizes duly supported at regular interval as per site requirement etc. complete as required as per specifications of 250 mm dia

od239068/2024_2025 : Supplying ; fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

od239071/2024_2025 : Supply, installation, testing ; commissioning of thermal insulated flexible duct of following sizes duly supported at regular interval as per site requirement etc. complete as required as per specifications of 200 mm dia

od239073/2024_2025 : Supply, installation, testing ; commissioning of thermal insulated flexible duct of following sizes duly supported at regular interval as per site requirement etc. complete as required as per specifications of 150 mm dia

od239075/2024_2025 : Supply, installation, testing ; commissioning of Butter fly dampers of GI construction made out of 22G sheet with lever, brass bush with spindle and locking arrangement at the take off for the supply air diffusers. complete as required as per specifications of 200 mm dia

od239077/2024_2025 : Supply, installation, testing ; commissioning of Butter fly dampers of GI construction made out of 22G sheet with lever, brass bush with spindle and locking arrangement at the take off for the supply air diffusers. complete as required as per specifications of 250 mm dia

16.17 : Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminum with aluminum volume control dampers with anti smudge ring and removable core.

16.18 : Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminum without volume control dampers with anti smudge ring and removable core.

od239081/2024_2025 : Supplying, fixing testing commissioning of Exhaust Disc Valve for the each disc valve

od239083/2024_2025 : Non Vision grills for the toilet doors. The grills shall be supplied in two matching halves and shall match the door thickness. The grills shall be powder coated .

od239085/2024_2025 : Supplying, fixing, testing ; commissioning of powder coated extruded aluminium section fresh air grill in weather maker room with aluminium volume control dampers, bird screen etc complete as required

od239087/2024_2025 : CONDENSATE DRAIN PIPING : Supply, inatallation, testing and commissioning of condensate drain UPVC piping as per BIS 4985 with necessary clamps, supports, hangers and fitting such as bend, tees, reducers etc. duly insulated with 9 mm thick chemically cross-linked closed cell ntrile rubber insulation, fire retardant grade as per the drawing and relavent standards - 20mm dia

od239089/2024_2025 : Supply,installation, testing and commissioning of condensate drain UPVC piping as per BIS 4985 with necessary clamps, supports, hangers and fitting such as bend, tees, reducers etc. duly insulated with 9 mm thick chemically cross-linked closed cell ntrile rubber insulation, fire retardant grade as per the drawing and relavent standards - 25mm dia

od239091/2024_2025 : Supply,installation, testing and commissioning of condensate drain UPVC piping as per BIS 4985 with necessary clamps, supports, hangers and fitting such as bend, tees, reducers etc. duly insulated with 9 mm thick chemically cross-linked closed cell ntrile rubber insulation, fire retardant grade as per the drawing and relavent standards - 40mm dia

od239092/2024_2025 : Underdeck insulation with 50mm thick TF quality Expanded polystyrene fixed to the slab with Rawl plugs and GI washers and tied with GI wire.

od239095/2024_2025 : SITC of Al.powder coated 6 continuous grill with end flanges

od239096/2024_2025 : SITC of Al.powder coated 4 continuous grill with end flanges

od239099/2024_2025 : SITC of Opposed blade collar dampers of powder coated Aluminium.

od239102/2024_2025 : Supply, installation, testing ; commissioning of Butter fly dampers of GI construction made out of 22G sheet with lever, brass bush with spindle and locking arrangement at the take off for the supply air diffusers. complete as required as per specifications of 150 mm dia

od239103/2024_2025 : Return air cross talk attenuators -Factory fabricated Z type made of 24G GI sheets of 300mm wide x 300mm height of 1.5m length with accoustic lining of 15mm thick open cell nitrile rubber insulation of class-1 accoustic 140-180 Kg / M3 density stuck to the clean internal surface of the duct with good quality low VOC content adhesive. Suitable size grille at the outlet to be considered accordingly.complete as required as per specifications. Type-01

od239106/2024_2025 : Return air cross talk attenuators -Factory fabricated Z type made of 24G GI sheets of 400mm wide x 500mm height of 1.5m length with accoustic lining of 15mm thick open cell nitrile rubber insulation of class-1 accoustic 140-180 Kg / M3 density stuck to the clean internal surface of the duct with good quality low VOC content adhesive. Suitable size grille at the outlet to be considered accordingly.complete as required as per specifications.Type-02

16.20.1 : Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/ main branch and return air path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications.Fire damper

od239107/2024_2025 : Supply, installation, testing and commissioning of Actuator for the above fire damper

STARTER PANEL VFD WITH BYPASS STARTER PANEL

od239001/2024_2025 : SITC of outdoor wheather proof Polycarbonate box of IP level 67 with 415V 4P 32/40/63 Ampere 100mA ELCB including all fixing mountings.

od239002/2024_2025 :SITC of Automatic timer control with Power connection for switching the Fan/AC etc. Consisting of the following1. 2 Nos. 63A, 415V, AC-4 duty 3P contactor-2 set2. Timer-1 No.3. Auxilliary switches and Push button, actuation etc.-1 set4. Enclosure fabricated with 16SWG CRCA sheet

ELEVATOR SEVICE WORKS- WARD TOWER

od239868/2024_2025 : Supply, installation, testing ; commissioning of electric traction type elevator of following capacities and type suitable for operation on 415 V, 3 phase, 50 Hz AC supply, having AC variable voltage and variable frequency type traction control, machine room less, speed of 1.00 Mtr/sec, electromagnetic brake system, simple operations, operating control panel with luminous buttons, overload warning indicator, battery operated alarm bell, LED type emergency light, intercom suitable for hook up to EPABX, infrared ray sensing door protection for full height, reverse phase relay on controller, fireman&rsquo;s switch at ground floor, digital car positions indicator in car and at all positions indicator in car and at all floors with Up/DOWN direction, all signal fixtures in stainless stell faceplates, light fixtures, ventilation fan, etc complete with all accessories including automatic rescue device in the event of power failure etc., Complete with necessary scaffolding,, logic control panel and shaft lighting etc required for the erection of the elevators as required.Machine Room Type and elevator shall be of gearless type (suitable for Shaft Size -2400 mmx 3000 mm) complete as per technical specification, simplex full collective operation with/without attendant. Car/Hoistway Entrance, protected by stainless steel hairline doors and clear center /side opening min 1100mm wide X 2000mm height. (Minimum)20 Passengers (1360 Kg) capacity Bed Lift , car size of 1300 MM W X 2400 MM x 2200mm Height Inside dimensions and entrance at front side on all the serving floors, provided with matt finish stainless steel panel on all four side and ceiling, with rear side handrail as per specifications.11 stops ; 11 openings ,Total travel height is approximately 40 M Passenger/bed lift

od239869/2024_2025 : Supply, installation, testing ; commissioning of electric traction type elevator of following capacities and type suitable for operation on 415 V, 3 phase, 50 Hz AC supply, having AC variable voltage and variable frequency type traction control, machine room less, speed of 1.00 Mtr/sec, electromagnetic brake system, simple operations, operating control panel with luminous buttons, overload warning indicator, battery operated alarm bell, LED type emergency light, intercom suitable for hook up to EPABX, infrared ray sensing door protection for full height, reverse phase relay on controller, fireman&rsquo;s switch at ground floor, digital car positions indicator in car and at all positions indicator in car and at all floors with Up/DOWN direction, all signal fixtures in stainless stell faceplates, light fixtures, ventilation fan, etc complete with all accessories including automatic rescue device in the event of power failure etc., Complete with necessary scaffolding,, logic control panel and shaft lighting etc required for the erection of the elevators as required.Machine Room Type and elevator shall be of gearless type (suitable for Shaft Size -2000 mmx 3000 mm) complete as per technical specification, simplex full collective operation with/without attendant. Car/Hoistway Entrance, protected by stainless steel hairline doors and clear center /side opening min 1000mm wide X 2000mm height. 16 passengers (Minimum1088 Kg) capacity Bed Lift , car size of 1300mm wide x2000mm deep x 2200mm Height Inside dimensions and entrance at front side on all the serving floors, provided with matt finish stainless steel panel on all four side and ceiling, with rear side handrail as per specifications.11 stops ; 11 openings ,Total travel height is approximately 40 M Passenger/bed lift

od239871/2024_2025 : SITC of Dump waiter of 100 kg capcity suitable for operation on 415 V, 3 phase, 50 Hz AC supply, having AC variable voltage and variable frequency type traction control, speed of 0.30 Mtr/sec, electromagnetic brake system, simple operations, operating control panel with buttons, reverse phase relay on controller, digital car positions indicator on wall at all floors with Up/DOWN direction, all signal fixtures in stainless steel faceplates, light fixtures, etc complete with all accessories. The equipment traction motor placed in the Machine Room, geared type with travel height of 12 mtrs. (suitable for well size 1200mm (W)X 1200m(D) simplex operation. Equipment entrance protected by SS doors with min 700mm x 700mm opening size. Complete with necessary scaffolding,logic control panel and shaft lighting etc required for the erection of the dump waiters. Capacity Minimum 100 Kgs, 2 stops ; 2 openings with min car size of 700mm wide x600mm deep x 800mm height Inside dimensions and entrance at front side on all the serving floors, provided with SS car on other three sides, SS finish ceiling Aluminium chequered plate flooring complete as per specifications.

ELEVATOR SEVICE WORKS- Diaganostic block

od239870/2024_2025 : Supply, installation, testing ; commissioning of electric traction type elevator of following capacities and type suitable for operation on 415 V, 3 phase, 50 Hz AC supply, having AC variable voltage and variable frequency type traction control, machine room less, speed of 1.00 Mtr/sec, electromagnetic brake system, simple operations, operating control panel with luminous buttons, overload warning indicator, battery operated alarm bell, LED type emergency light, intercom suitable for hook up to EPABX, infrared ray sensing door protection for full height, reverse phase relay on controller, fireman&rsquo;s switch at ground floor, digital car positions indicator in car and at all positions indicator in car and at all floors with Up/DOWN direction, all signal fixtures in stainless stell faceplates, light fixtures, ventilation fan, etc complete with all accessories including automatic rescue device in the event of power failure etc., Complete with necessary scaffolding,, logic control panel and shaft lighting etc required for the erection of the elevators as required.Machine Room Type and elevator shall be of gearless type (suitable for Shaft Size -2000 mmx 3000 mm) complete as per technical specification, simplex full collective operation with/without attendant. Car/Hoistway Entrance, protected by stainless steel hairline doors and clear center /side opening min 1000mm wide X 2000mm height. 16 passengers (Minimum1088 Kg) capacity Bed Lift , car size of 1300mm wide x2000mm deep x 2200mm Height Inside dimensions and entrance at front side on all the serving floors, provided with matt finish stainless steel panel on all four side and ceiling, with rear side handrail as per specifications.5 stops ; 5 openings ,Total travel height is approximately 22 Meters

MGPS SERVICE WORKS - MANIFOLD AND PLANT ROOM - OXYGEN SYSTEM

od238940/2024_2025 : Supply,testing and commissioning of Oxygen Manifold - 2 banks x16 cylinders, as per technical specifications. The cylinders shall not be included in the quoted price.

od238945/2024_2025 : Supply,testing and commissioning of Cylinder Emergency Oxygen Manifold with high flow regulator- 1 Bank X5 Cylinders

od239875/2024_2025 : Supply, installation testing and commissioning of Automatic Oxygen Control Panel with minimum flow rate of 2000 LPM with liquid oxygen connectivity, suitable for 2x16 manifold system and provision for accommodating oxygen line from LMO Fully complying with ISO 10524-2, ISO 7396-1:2007/HTM02-01 as per technical specifications. The cylinders shall not be included in the quoted price.

NITROUS OXIDE SYSTEM

od238919/2024_2025 : NITROUS OXIDE SYSTEM: Supply,testing and commissioning of automatic N2O control panel complete set with inlet and outlet connectors suitable for 2x3 manifold system with minimum flow rate of 600 LPM, fully automatic control panel for both sides with brass hosing and suitable connectors.BSP (M) thread.

od238927/2024_2025 : Supply,testing and commissioning of Cylinder Manifold Nitrous oxide - 2 bank x 3cylinders as per technical specifications.

od238933/2024_2025 : Supply,testing and commissioning of Nitrous Oxide Emergency Manifold - 1 banks x 2 cylinders with hogh flow Regulator.as per technical specifications. The cylinders shall not be included in the quoted price.

CARBON DIOXIDE SYSTEM

od238909/2024_2025 : Supply,testing and commissioning of Cylinder Emergency CO2 Manifold - 2 bank x 1 cylinder with a high flow regulator with gauges and safety valves complete with all accessories etc. as required complete as per specification

od238922/2024_2025 : CARBON DIOXIDE SYSTEM: Supply,testing and commissioning of semi automatic CO2 control panel complete set with inlet and outlet connectors for automatic for both sides with brass housing and suitable connectors. BSP (M) thread.

MEDICAL AIR SYSTEM

od238928/2024_2025 : MEDICAL AIR SYSTEM: Supply, testing and commissioning of Compressed air plant complete with - 2 compressors, each compressor should have minimum free air delivery of 2000 LPM @10bars, 1 air receiver tank of minimum 2000 ltr capacity, filtration and dryer system to ensure medical air quality as per HTM standards (each compressor module should include an inline filter with particle retention of 10 microns), NRV, pressure reducing station, automatic drain valves, pressure guages, ball valves, electrical control panel including circuit breakers, starters, pressure switches, timers, as per technical specifications

VACCUM PLANT

od238929/2024_2025 : Supply, Installation, testing and commissioning of Rotary Vane type Oil-lubricated Duplex Medical Vacuum Plant (Package Unit) having a capacity of 3000 LPM including 2 Nos Vacuum pump, air receiver tank with 3000 litre, filters, dryers, valves, NRV, pressure gauge, pressure switch, Electrical control panel, starters, timer, circuit breaker all accessories as per HTM 02-01/NFPA 99C standards.

Distribution panel

od238934/2024_2025 : Supply, Installation, testing and commissioning of 3 phase ,6 way TPN MCCB DB consisting of 100 Amp 4P MCCB as incomer, outgoing of 6 nos 40/32 TP D curve MCB, cable termination box etc. complete.

PIPE LINE SYSTEM

od238913/2024_2025 : Supply,installation testing and commissioning of Copper pipe: as per stanard BS:EN13348:2008 /astm B819 standards,solid drawn,seamless,deoxidized,non-arsenical,half hard tempered and degreased copper pipe conforming to the standardwith all fiiings supporting materials bracing, pressure testing etc as per standards.All copper pipes should be degreased and delivered at both ends of required sizes and as per technical specifications.12mm x 1 mm thick Copper pipe

od238921/2024_2025 : Supply, installation testing and commissioning of Copper pipe: as per standard BS:EN13348:2008 /astm B819 standards, solid drawn, seamless, deoxidized, non-arsenical, half hard tempered and degreased copper pipe conforming to the standardwith all fiiings supporting materials bracing, pressure testing etc as per standards .All copper pipes should be degreased and delivered at both ends of required sizes and as per technical specification -15mm x 0.9mm thick copper pipe

od238935/2024_2025 : Supply, installation testing and commissioning of Copper pipe: as per standard BS:EN13348:2008 /astm B819 standards, solid drawn, seamless, deoxidized, non-arsenical, half hard tempered and degreased copper pipe conforming to the standardwith all fiiings supporting materials bracing, pressure testing etc as per standards. All copper pipes should be degreased and delivered at both ends of required sizes and as per technical specifications.22 mm x0.9 mm thick Copper pipe

od238941/2024_2025 : Supply, installation testing and commissioning of Copper pipe: as per standard BS:EN13348:2008 /astm B819 standards, solid drawn, seamless, deoxidized, non-arsenical, half hard tempered and degreased copper pipe conforming to the standardwith all fiiings supporting materials bracing, pressure testing etc as per standards. All copper pipes should be degreased and delivered at both ends of required sizes and as per technical specifications.28 mm x 0.9 mm thick Copper pipe

od238948/2024_2025 : Supply,installation testing and commissioning of Copper pipe: as per stanard BS:EN13348:2008 /astm B819 standards,solid drawn,seamless,deoxidized,non-arsenical,half hard tempered and degreased copper pipe conforming to the standardwith all fiiings supporting materials bracing, pressure testing etc as per standards.All copper pipes should be degreased and delivered at both ends of recquired sizes and as per technical specifications. 35mm x 1.2 mm thick Copper pipe

od238950/2024_2025 : Supply of Copper pipe: as per stanard BS:EN13348:2008 /astm B819 standards,solid drawn,seamless,deoxidized,non-arsenical,half hard tempered and degreased copper pipe conforming to the standardwith all fiiings supporting materials bracing, pressure testing etc as per standards. All copper pipes should be degreased and delivered at both ends of recquired sizes and as per technical specification 42 mm x 1.2 mm thick copper pipe

od238953/2024_2025 : Supply of Copper pipe: as per stanard BS:EN13348:2008 /astm B819 standards,solid drawn,seamless,deoxidized,non-arsenical,half hard tempered and degreased copper pipe conforming to the standardwith all fiiings supporting materials bracing, pressure testing etc as per standards. All copper pipes should be degreased and delivered at both ends of recquired sizes and as per technical specification 54 mm x 1.2 mm thick copper pipe

od238955/2024_2025 : Supply of Copper pipe: as per stanard BS:EN13348:2008 /astm B819 standards,solid drawn,seamless,deoxidized,non-arsenical,half hard tempered and degreased copper pipe conforming to the standardwith all fiiings supporting materials bracing, pressure testing etc as per standards. All copper pipes should be degreased and delivered at both ends of recquired sizes and as per technical specification 72mm x 1.2 mm thick copper pipe

GAS OUTLETS

od238918/2024_2025 : Supply,Installation , testing and commissioning of Gas Outlets meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications. Venturi type AGSS outlets conforming to EN ISO 9170-2

od238925/2024_2025 : Supply,Installation , testing and commissioning of Gas Outlets meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications. O2 Outlets with Probes

od238937/2024_2025 : Supply,Installation , testing and commissioning of Gas Outlets meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications. Vac Outlets with Probes

od238942/2024_2025 : Supply,Installation , testing and commissioning of Gas Outlets meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications. Air (7 bar) Outlets with Probes

od238947/2024_2025 : Supply,Installation , testing and commissioning of Gas Outlets meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications-Air (4 bar) Outlets with Probes

od238952/2024_2025 : Supply, Installation , testing and commissioning of Gas Outlets meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications. N2O Outlets with Probes

od238954/2024_2025 : Supply,Installation , testing and commissioning of Gas Outlets meeting requirements of EN ISO 9170-1/ HTM 02-01/DIN as per technical specifications.CO2 Outlets with Probes

MASTER ALARM PANEL

od238911/2024_2025 : Supply,testing and commissioning of Master Plant Alarm Panel ,Complies with HTM 02-01/ISO 7396-1 Standards. Each Master Alarm should be modular in design and be fitted with required number of master alarm modules. The master alarms should be capable to monitor minimum 25 point. Each point represents an alarm condition that the source equipment might have. When an alarm condition exists, a red-light flashes and the audible alarm sounds. If several alarm conditions occur simultaneously, the most recent alarm light should flash, while the other alarm lights should remain lit. When an alarm condition is created, an audible alarm should be actuated. A dry contact module should be available to interface with a building management system. The box material should be of gauge steel of requisite thickness and equipped with mounting brackets. The emissions from alarms should conform with EMC standards. Master alarm management system should be designed to display alarm conditions from the source supply units indicating the broad status of the source equipment and manifolds as well as the master distribution status from the source supplies. Depending on the alarm priority, a visual and audible alarm should be initiated to indicate an alarm condition. Each panel shall display and/or input of multi point alarms,including all necessary cabling between mater alarm and floor panels. The master alarm must be able to monitor the following source alarm conditions. as per technical specifications.Master Plant Alarm Panel ,Complies with HTM 02-01/ISO

AREA VALVE AND ALARM UNIT

od238912/2024_2025 : Supply,Installation,testing and commissioning of Area Valve Service + Alarm Units, fully complying, by means of pressure sensors which detect deviations from the normal operating limits of either pressure or medical vacuum. The area alarm should have a digital/analogue display of pressures. The medical gas area alarm should fully satisfy the NFPA 99/HTM 02-01/ISO 7396-1 requirements and should be European CE Certified or UL listed. An audible warning should sound simultaneously with any failure indication and a mute facility should be provided as per technical Specifications. 6gas

od238926/2024_2025 : Supply,Installation,testing and commissioning of Area Valve Service + Alarm Units, fully complying, by means of pressure sensors which detect deviations from the normal operating limits of either pressure or medical vacuum. The area alarm should have a digital/analogue display of pressures. The medical gas area alarm should fully satisfy the NFPA 99/HTM 02-01/ISO 7396-1 requirements and should be European CE Certified or UL listed. An audible warning should sound simultaneously with any failure indication and a mute facility should be provided as per technical Specifications. 5gas-

od238931/2024_2025 : Supply,Installation,testing and commissioning of Area Valve Service + Alarm Units, fully complying, by means of pressure sensors which detect deviations from the normal operating limits of either pressure or medical vacuum. The area alarm should have a digital/analogue display of pressures. The medical gas area alarm should fully satisfy the NFPA 99/HTM 02-01/ISO 7396-1 requirements and should be European CE Certified or UL listed. An audible warning should sound simultaneously with any failure indication and a mute facility should be provided as per technical Specifications. 4gas -

od238943/2024_2025 : Supply,Installation,testing and commissioning of Area Valve Service + Alarm Units, fully complying, by means of pressure sensors which detect deviations from the normal operating limits of either pressure or medical vacuum. The area alarm should have a digital/analogue display of pressures. The medical gas area alarm should fully satisfy the NFPA 99/HTM 02-01/ISO 7396-1 requirements and should be European CE Certified or UL listed. An audible warning should sound simultaneously with any failure indication and a mute facility should be provided as per technical Specifications. 3 gas -

od238946/2024_2025 : Supply,Installation,testing and commissioning of Area Valve Service + Alarm Units, fully complying, by means of pressure sensors which detect deviations from the normal operating limits of either pressure or medical vacuum. The area alarm should have a digital/analogue display of pressures. The medical gas area alarm should fully satisfy the NFPA 99/HTM 02-01/ISO 7396-1 requirements and should be European CE Certified or UL listed. An audible warning should sound simultaneously with any failure indication and a mute facility should be provided as per technical Specifications. 2 gas -

BALL VALVES

od238916/2024_2025 : Supply,installation, testing and commissioning of Ball Valves, complying with HTM 02-01/DIN, as per technical Specifications-54mm

od238930/2024_2025 : Supply,installation, testing and commissioning of Ball Valves, complying with HTM 02-01/DIN, as per technical Specifications-42mm

od238932/2024_2025 : Supply,installation, testing and commissioning of Ball Valves, complying with HTM 02-01/DIN, as per technical Specifications-35mm

od238944/2024_2025 : Supply,installation, testing and commissioning of Ball Valves, complying with HTM 02-01/DIN, as per technical Specifications28mm

od238949/2024_2025 : Supply,installation, testing and commissioning of Ball Valves, complying with HTM 02-01/DIN, as per technical Specifications-22mm

od238951/2024_2025 : Supply,installation, testing and commissioning of Ball Valves, complying with HTM 02-01/DIN, as per technical Specifications-15 mm

OXYGEN GAS CYLINDER

od238914/2024_2025 : Supply,testing and commissioning of D type CO2 Gas filled Cylinder having as per technical specification.D type CO2 Gas filled Cylinder

od238923/2024_2025 : Supply,testing and commissioning of D type Nitrous Oxide Gas filled Cylinder as per technical specification.D type Nitrous Oxide Gas filled Cylinder

od238938/2024_2025 : Supply, testing and commissioning of class D type Oxygen Gas filled Cylinder etc in complete as per technical specification.

BED HEAD PANELS

od238910/2024_2025 : Supply and installation of Bed Head 5ft(Horizontal) unit made out of High sbength extruded Aluminum Panel of minimum 2.5 mm thickness with powder coated to make it aesthetically appealing and long lasting, the panel should be divided into different sections to segregate power, data and medical gas chamber suitable for accommodating following utilities - Oxygen, Vacuum, Medical Air, Nurse call switch 1, spare probe, 2 no 5 /15A combined socket with switch outlet ;mdash; 2 set, provision RJ-45 socket/ Ethernet, shall have monitor holder and equipped with two side rail system to hold different associated accessories like vaccine basket, Holder for vacuum collection jar, examination lamp, IV pole, etc. and all necessary mechanical supports for complete installation as instructed and directed by engineer in- charge. Bed head panel as above with 2 Gas outlet

od238920/2024_2025 : Supply and installation of Bed Head 5ft (Horizontal) unit made out of High sbength extruded Aluminum Panel of minimum 2.5 mm thickness with powder coated to make it aesthetically appealing and long lasting, the panel should be divided into different sections to segregate power, data and medical gas chamber suitable for accommodating following utilities - Oxygen, Vacuum, Medical Air, Nurse call switch ; 1, spare probe, 2 no 5 /15A combined socket with switch outlet ;mdash; 2 set, provision RJ-45 socket/ Ethernet, shall have monitor holder and equipped with two side rail system to hold different associated accessories like vaccine basket, Holder for vacuum collection jar, examination lamp, IV pole, etc. and all necessary mechanical supports for complete installation as instructed and directed by engineer in- charge. Bed head panel as above with 5 Gas outlet

od238917/2024_2025 : Supply, Installation, testing and commissioning of High Pressure Antistatic Hose with color coded.

od238924/2024_2025 : Supply Installation of Theatre Vacuum unit with trolly and 2000 ml collection jar as per technical.

od238936/2024_2025 : Supply Installation of Ward vacuum unit with 600 ml collection jar asper technical specification.

od238939/2024_2025 : Supply Installation of BPC Oxygen Flow meter as per technical specification.

Ramkrishy Infrastructure Pvt Ltd (BID ID -2330979)

THE URALUNGAL LABOUR CONTRACT CO-OPERATIVE SOCIETY (BID ID -2336062)

Bidder Name

THE URALUNGAL LABOUR CONTRACT CO-OPERATIVE SOCIETY

R K INFRA (INDIA) PVT LTD

Ramkrishy Infrastructure Pvt Ltd