MLA-SDF-Thiruveeshamkulam Road Renovation -Thiruveeshamkulam Road Renovation (Both Tarring and Interlock) Piravom Municipality

Amount

Road Interlocking and Tarring

OD498616/2024-2025:Sectioning up to 150mm and forming the surface for OLD road way levelling,cambering etc complete as per direction of Engineer in charge

4.1.A.1:Granular Sub-base with Well Graded Material (Table 400.1) (A) By Mix in Place Method Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. (i) For Grading I Material

OD498615/2024-2025:Providing and Laying of Interlocking Concrete Block Pavements using 80mm M40 hydraulic blocks of approved size ,design &shape ,laid in required pattern over and including a compacted bed of 6mm stone aggregate of 50mm average thickness,etc. all complete as per the direction of Engineer-in-charege.

4.9:Wet Mix Macadam Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406. By Mechanical Means with 1 km lead

75.5.1.1pb:Prime Coat - Low porosity - With Packed Bitumen Rates Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

75.5.2.3pb:Tack Coat - With Packed Bitumen Rates Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503.

75.5.11.1.A.2pb:Mix Seal Surfacing - Manual Means - Type A - Bitumen S-65 - Packed Bitumen Rates Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification Clause 509 By Manual Means Type A (II) Bitumen (S-65)

75.8.1.1.A:Providing Plain cement concrete for wearing coat CC 1:2:4 (1 cement: 2 fine aggregate:4 course aggregate) laid to required slope as required including compaction, finishingand tamping etc .complete. Max. size of course aggregate not exceeding 25mm , mixedin concrete mixer etc complete as per specification (i) Nominal mix (1:2:4)

OD499338/2024-2025:Steel work welded in built up sections/framed work , including cutting ,hoisting , fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 10.25.2 In gratings ,frames, guard bar, ladder, railings, brackets, gates and similar works

10.6:Painting on Steel Surfaces Providing and applying two coats of ready mix paint including primer coat of approved brand on steel surface after through cleaning of surface to give an even shade as per drawing and Technical Specification Clause 1701

OD498614/2024-2025:Supplying and fixing in place granite nameboard of slab area less than .9 sqm including engravingand painting lettersetc complete as per direction of Engineerincharge at site

K A SABU (BID ID -2224675)

Bidder Name

K A SABU

Mc.Rajan