IMPROVEMENT TO CERTAIN AIRMEN MARRIED ACCOMODATION AT AF STN BAREILLY

Amount

INTERNAL SERVICES (B/R)

Dismantling brick tiles of any thickness or description complete all as specified and directed.

Demolition of Mud in roof any thickness incl plastering & leeping and removal of demolished material to a distance exc. 2 KM but n.exc 2.5 KM complete all as specified and directed.

M&L for providing PCC 1:3:6 type-C1, (using 20mm graded stone aggrigate) padding over slab as levelling course complete all as specified and directed.

M&L for water proofing treatment on approachable roof with following Specifications : 1. Average 10mm thick plaster in CM 1:3 mixed with polymer based water proofing compound when levelling coarse is still green. 2. After the surface is fully dried, applying a coat of bituminous primer @ 0.30 liters/Sqm. 3. After primer, the entire roof surface shall be painted with hot, blown bitumen grade 85/25 confirming to IS-702 @ 1.2 Kg/Sqm 4. Over hot bitumen, polymeric water proofing membrane consisting of 90 to 100 micron thick central core of HMHDPE film and standard weight 3 Kg/Sqm shall be laid with 100mm side lap/end lap on prepared surfaces as per manufacture’s instruction and strict supervision of manufacture’s technical representation. 5. Laying 20mm thick PCC tiles machine pressed 250 X 250 X 20-25MM, factory made as per IS-1237-1980 with gray cement and pigment laid over a bedding layer of 15mm screed in cement mortar 1:3. The cement mortar screed and tiles joints shall be filled with polymer based cement proof joint filler manufactured by approved specification/instructions and tiles joints shall be filled with polymer based cement proof joint filler manufactured by approved company. complete all as specified and directed.

M&L cutting out cracks to V section in existing roof ,chajjas or similar work up to 40 mm deep and cleaning the same with water jets to get rid of any loose material and wetting ,grouting with cement & sand morter 1:3 mixed with liquid WPC complete all as specified and as directed .

M&L plain cement concrete 1:2:4 mix type B-1 (using 20 mm graded stone agg) as in roof kerb and the like rounded or chamfered on edges complete all as specified and directed.

Demolition of un-reinforced cement concrete of any description and in any position not otherwise specifically provided for incl removal of demolished material to a distance exc. 2 KM but n.exc 2.5 KM complete all as specified and directed.

Demolition of brick work built in cement mortar or cement lime mortar including all quions, arches, pillers etc complete all as specified and directed.

M&L for fly ash Brick works, straight or curved on plan exc 6.0 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

Dismantling existing water tank of capacity n exc 500 ltrs ,setting aside or lowering if reqd for repairs ,cleaning etc and hoisting ,reconnecting and refixing in position complete all as specified and directed

Dismantling water tank of capacity n exc 500 ltrs complete all as specified and directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removal to store 15 mm bore complete all as specified and directed.

Taking up or down steel tubing and connections, inclusing cleaning for refixing or removal to store 20 mm bore complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc, (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks three layers (Cylindrical vertical with closed top) of 500 ltrs capacity hoisted and fixed in position complete all as specified and directed in SSR Pt I .

S&F in repair PVC ball cock, 20 mm bore high pressure of PTMT apoxy coating aluminium rod , with polythene float and flynut complete, screwed for iron pipe complete all as specified and directed.

S&F 15 mm bore of galvanised steel tubing medium grade with all fittings complete to walls including cutting chases and ceilings or laid in floors complete all as specified and directed.

S&F 20 mm bore of galvanised steel tubing medium grade with all fittings complete to walls including cutting chases and ceilings or laid in floors complete all as specified and directed.

Refixing old GI tubing and connection in new or old location after taking down ,cleaning etc complete 20 mm bore complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed , in any length with rubber ring joints fixed to walls with MS clamps complete all as specified and directed.

S&F PVC (SWR) bends any radius of bore 110 mm complete all as specified and directed.

S&F in repairs cast iron pipe floor trap long neck type 75 mm dia without greating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 , complete all as specified and directed

S&F 75 mm dia bore cast iron sand cast soil waste and vent pipe in any length with or without ears, with lead joint laid in tranches or in floor complete all as specified and directed.

S & F of 100 mm bore cast iron soil sand cast soil, waste and vent pipe, sand cast, in any length, with or without ears, with cement joints in cement sand mortar 1:1 with spun yarn laid in trenches or fixed to walls all as specified and directed.

S & F of 100 mm bore cast iron bend (any radius), diminishing piece or taper (larger bore measured) complete all as specified and directed.

S & F of 75 mm bore cast iron bend (any radius), diminishing piece or taper (larger bore measured) complete all as specified and directed.

S&F cast iron cowl 75mm bore complete all as specified and directed.

S & F of 100 mm bore cast iron Branch pieces, single (equal or unequal) , ordinary or inverted(spigot or socket type)or with parallel branches complete all as specified and directed.

S & F of 75 mm bore cast iron Branch pieces, single (equal or unequal),ordinary or inverted(spigot or socket type)or with parallel branches complete all as specified and directed.

S&F Stack clamps for 75 mm bore pipe out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S&F Stack clamps for 100 mm bore pipe out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes 100/75mm dia of any radius jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

S&F in repairs vitreous china sqautting pan orissa pattern size 580 x 440 mm white with intergral foot rest including cast iron "P" or "S" trap and PVC flush pipe but excluding flushing cistern including making good floor as per existing complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) incl removal of demolished material to a distance exc. 2 KM but n.exc 2.5 KM complete all as specified and directed.

M&L 75 mm thick cement concrete 1:3:6 , type C1, (using 20 mm graded stone agg ) in plinth protection, laid in bay n exc 3.00 m long each finished even and smooth without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm wide joints through out the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and directed.

S & F in-repair Vitreous china wash basin, white, flat back of size 550mm x 400mm including cutting for and pinning in ends of the brackets or erecting stand complete all as specified and directed.

S & F in-repair PVC low level flushing cistern dual flush white colour 10 Litres capacity, valve less, with inlet, ball valve, float and handle including brackets, PVC flush bend pipe complete all as specified and directed.

S & F in repairs; stop valves/angle cock 15mm dia of pipe in cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed but fancy type chromium plated with long shank and cup complete all as specified and directed.

S & F in repairs; PVC connection 45 cm long with two nuts and washers complete all as specified and directed.

S&F 15mm Brass CP mixer for mixing for kitchen sink hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F 15mm Brass CP mixer 2 in1 for mixing for WHB hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F 15mm CP brass wall mixure three in one with hand shower with accessories with mark Hot and Cold complete all as specified and directed .

S & F in repairs; 15mm bib taps, chromium plated with fancy head with or without littered “Hot” or “Cold” screwed down, screwed for iron pipe of 15mm bore dia fancy type complete all as specified and directed .

S&F corner self fency type three tier with 5.50mm thick glass mounted on CP brass frame fixed with brass screw & plug .Size n less than 450mm as suitable for bath room as per manufacturer instruction complete all as specified and directed.

S & F Grating doom 100mm dia of Stainless steel AISI 304 complete all as specified and directed.

S & F in repair brass chromium plated shower rose 125mm size with swivel joint incl a shower arm 15mm size, 195mm long with bend of 45degreee with flange of PTMT any colour , (Minimum weight 40 gms) complete all as specified and directed.

S & F tubular towel rail 20mm dia D type 60cm long between flanges brass chromium plated complete fixed to walls complete all as specified and directed.

Supply and fixing fency type soap dish, chromium plated complete all as specified and directed.

S& Fixed in repair 20mm dia Gun-metal, glove or gate valves, with iron wheel head, screwd both end sor iron pipe and fixed complete all as specified and directed.

Taking down cement plaster including racking out joints hacking for key and scrubbing down with water complete all as specified and directed.

M&L for 15 mm thick rendering in cm (1:4) on brick or concrete surfaces finished fair and even including mixed with liquid WPC as per manufacturer instruction complete (Note :- WPC will be measured and paid separately). The work is to be carried out upto 8.0 mtr height from G.L.

M&L for rendering 15 mm thick in patch in cement mortar 1:6 on fair face of brick work or concrete surfaces with surface finish even and smooth complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and diredcted.

M&L for 10 mm thick rendering in CM (1:3) on concrete surfaces on ceiling complete all as specified.

M&L for prepration of new plastered surface of wall and applying two coat of cement base paint over one coat of primer complete all as specified and directed.

M&L for applying two coats of OBD over a coat of 1.5 mm thick wall care putty after making the putty surface fair , even and smooth by sand papering the surfaces on walls, complete all as specified and directed.

M&L for applying two coats of OBD over a coat of 1.5 mm thick wall care putty after making the putty surface fair , even and smooth by sand papering the surfaces on ceiling, complete all as specified and directed.

M&L for three coats of white wash on ceiling including preparation of newly plastered surfaces complete all as specified.

M&L for prepration of surface incl brooming down or steel wire brushing ,scrapping down smoke soot ,moulds , moss and efforescent salts and applying one coat of white wash on old decorated surfaces on ceiling compele all as specified and directed.

M&L Preparation of old surfaces including brooming down to remove all dust,dirt and loose scales of item and other foreign matter or steel wire brushing scrapping down smoke soot,grease spots moulds moss and efforescent salts and trading oil and applying two coat of cement base paint on wall all as specified and directed

M&L complete removal of existing treatment from walls for applying two coats of OBD over a coat of 1.5 mm thick wall care putty after making the putty surface fair , even and smooth by sand papering the surfaces on walls , complete all as specified and directed.

M&L complete removal of existing treatment from ceiling for applying two coats of OBD over a coat of 1.5 mm thick wall care putty after making the putty surface fair , even and smooth by sand papering the surfaces on ceiling , complete all as specified and directed.

M&L Preparation of old surfaces including brooming down to remove all dust,dirt and loose scales of item and other foreign matter or steel wire brushing scrapping down smoke soot,grease spots moulds moss and efforescent salts and trading oil and applying one coat of white wash on wall all as specified and directed

Taking down chowkat or frame with shutter( without taking off shutter from frame ) exc 1.5 sqm & n exc 4 sqm each complete complete all as specified and directed

Taking down chowkat or frame with shutter( without taking off shutter from frame ) n exc 1.5 sqm each complete all as specified and directed

Taking down shutter of any description exc 2 sqm each complete all as specified and directed

Taking down shutter of any description exc 1 sqm and n exc 2sqm each complete all as specified and directed

S & F factory made PVC door frame of size 50 x 47mm with a wall thickness of 5mm grid PVC sheet mitered at corner and pinned with two members 150mm long brackets of 15 x 15mm MS Square tube 19 gauge EPDM rubber gasket weathered sheet to be provided through the frame, door frame to be fixed to the wall suing MS screw of 65/100mm size complete as per manufacturer specification.

S & F 30mm thick factory made solid panel PVC door shutter conforming as per IS-4020 made from MS tube of 19 Gauge thickness of size 19 x 19mm style and 15 x 15mm for rail covered with heat moulded PVC channel of 5mm thick and 75mm, 125mm, 125mm wide for top rail, lock rail and bottom rail on either side at 5mm thick 20mm wide cross PVC sheet of gap inserted for top rail and bottom rail, paneling of 5mm PVC sheet fitted in MS frame welded/sealed to the style at rail with 30mm wide, 5mm thick PVC sheet beading sides and jointed together with solvent cement adhesive etc including aluminimum mongry complete all as specified and directed by Engineer-in-Charge.

M&L 2nd class hard wood for Plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed .

M&L for Flush shutters, 35mm solid core construction, with block board core and plywood face panels, commercial type on both sides and one face is covered with deco rative face veneer with lipping/frame to match complete all as specified and directed .

M&L Glazed and skeleton 35mm shutters 2nd class hard wood, open rebated and prepared to receive glass, gauze, etc. (with sash bars), edge of framing plain, chamfered or rounded, fitted withcut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. cla-use 8.20 (a); supplied and fitted to chowkats but divided into squares, with plain,chamfered or roun ded, mitred and rebated sash bars, any numbers complete all as specified and directed .

S&F sliding door bolts 300 mm long Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed .

S&F sliding door bolts 250 mm long Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed .

S & F 100mm long Mild steel butt hinges, cold rolled MS, medium type,and fixed complete all as specified and directed .

S & F for 125 mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed .

S&F 150mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed

S&F mild steel 300mm, ordinary rat tail rod patttern springs includding roller and roller plate complete all as specified and directed .

M&L for painting to new wooden surfaces of any description not otherwise described over 10cm wirdh or girth, with two coats of synthetic enamel paint (1st quality), over one coat of pink primer including preparation of surface complete all as specified and directed.

M&L for painting to old steel surfaces of any description over 10cm wirdh or girth, with two coats of synthetic enamel paint (1st quality), over one coat of primer including preparation of surface complete all as specified and directed.

M&L for preparing surface of new wood & steel of any descrition not other wise described and treated with tar or coal tar black paint complete all as specified and directed.

M&L for treating small article such as hold fast area n.exc 0.1 each with black tar or coal tar black paint complete all as specified and directed.

Supply and providing mild steel (base Steel as per IS 513 D Quality) Prefabricated, Pre-coated windows and ventilators of size exc 1 Sqm & n. exc 3 Sqm consisting both the glazed and wire glazed shutter, grill and fittings with following specifications and all as specified and directed:- (a) Frame shall be of 0.60mm thick powder coated rolled section of size 72mm x 55mm and mullon shall be 75mm x 49mm (design of window as per existing window) fitted with nylone self expending caps and driving MS electroplated 80mm long screw. (b) frame of glazed shutter shall be 47mm x 22mm and glass beed shall be 12mm x 12mm fitted with nylone/polypropylene corner brackets and mulion clips all per manufacturer instructions. (c) frame of wire gauzed shutter shall be 40mm x 20mm and glass beed shall be 12mm x 12mm fitted with nylone/polypropylene corner brackets and mulion clips all per manufacturer instructions. (d) MS grill shall be powder coated made with 10mm Square bar@ 110mm centre to center welded to mild steel flat 12mm x 6mm fitted with machine screw to window frame . (e) Rubber gasket EPDM shall be used for all glass and gauzed shutter. (f) 2 SS hinges , 1 poweder coated handle, tower bolt 75mm-2 Nos with1 seccolar stay for wiremesh shutter shall be provided with each shutter. Note:- Glass and wire mesh shall be measured and paid separately under respective item (g) Paint- Epoxy Primer 5-7 micron thick finish, painted with a polyester paint of 12-16 Micron or power coated with pure polyester poeder 50-60 micron thick.

All as per item No 1.085 Above but size of window/ventilator n exc 1 Sqm complete all as specified and directed.

S&F 150mm long Aluminium handles, cast type, anodised complete all as specified and directed

M&L 140mm length of Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring , Fixed in floor complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 100mm long Aluminium hing , cast type, anodised complete all as specified and directed.

S&F 3mm thick Sheet glass, ordinary quality and glazing with oil putty square in n exc 0.5 sq.m in each pane complete all as specified and directed.

S&F 3mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed.

Hacking out old broken glass (any thicknesss, size,quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish to a distance exc. 2 KM but n.exc 2.5 KM complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4 type B-0 ( using 12.5 mm thick graded stone aggregate) , rough to receive floor tiles etc complete all as specified and directed.

M&L brushing neat cement slurry with 3kg cement per sqm complete all as specified and directed.

M&L screed bed 15 mm thick in CM (1:6) in floors , finished rough to receive tiles etc complete all as specified and directed.

M&L 10 mm thick plastering in cement mortar 1:4 brick or on concrete surfaces of wall and finishing the surfaces fair and rough to receive tiles etc complete all as specified and directed.

M&L Non Skid colour ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cemeent to match complete all as specified and directed.

M&L Light shade colour ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cemeent to match complete all as specified and directed.

M&L Glazed ceramic coloured/printed tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

S & F of 18mm thick HDHMR board exterior grade, including acrylic high gloss sheet of 3mm thick over MDF board,anti fungal,moisture resistence,anti borer, as per IS 14587 for frame and shutter for kitchen cabinets/Cupboards etc. complete all as specified and directed by Engg-in-charge. NOTE:- Sample as approved by GE .

S & F of 18mm thick HDHMR board exterior grade, Both side laminated with any colour anti fungal,moisture resistence,anti borer, as per IS 14587 for kitchen/Cupboards shelfs fixing with 1st class hard wood lipping/beading etc. complete all as specified and directed by Engg-in-charge. NOTE:- Sample as approved by GE .

S & F of 12mm thick UV coating, HDHMR board exterior grade, Both side laminated with any colour anti fungal,moisture resistence,anti borer, as per IS 14587 for kitchen/Cupboards shelfs fixing with 1st class hard wood lipping/beading etc complete all as specified and directed by Engg-in-charge. NOTE:- Sample as approved by GE .

S&F 100mm long Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F Ball catches with 8 mm dia steel ball and brass body suitable for cupboard and stricking plate complete all as specified and directed.

S&F 40 mm dia cupboard knobs fixed with nut, screws of brass bright complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel, bright finish Width of flaps (When open) in 30 mm or electrogalvanised complete all as specified and directed.

S & F in repairs of stainless steel cupboard/cabinet / drawers handle having a length of 250mm and shape complete all as specified and directed.

S&F brass Locks 2 levers, for cupboard, grade I, size 65mm complete all as specified and directed

S&F in repairs 25 mm dia PVC coated , 0.63 mm thick MS Dapery rods with two nos of polished end caps & 2 nos powder coated M. S. brackets in each rod , complete all as specified and directed.

Drilling holes for cooking plateform in stone slab for gas pipe etc n. exc 25mm dia complete all as specified and directed

S&F soft wood beads chamfered , splays, grooves, rebates, rounded angles, rounded nosings, tongued and grooved edges (each tongue and each groove measured) etc., exc 3mm but n. exc 75mm girth complete all as specified and directed.

Mild steel bars 10mm dia TMT bars and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified and directed.

Mild steel bars 6 to 8mm dia TMT bars and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified and directed.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished surface of concrete complete all as specified and directed.

M & L for providing reinforced cement concrete 1:1.5:3 (Nominal Mix) type B-1, (using 20 mm graded stone aggregate) , as in in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and the like complete all as specified and directed.

Demolition of reinforced cemet concrete of any description roofs,floors(other than ground floors) beams, staircases, landings, chajjas and simillar suspended work incl removal of demolished material to a distance exc. 2 KM but n.exc 2.5 KM complete all as specified and directed.

M&L Roof treatment on vertival /facia surface as mentioned below :- 1After the surface is fully dried, applying a coat of bituminous primer @ 0.30 liters/Sqm. 2. After primer, the entire roof surface shall be painted with hot, blown bitumen grade 85/25 confirming to IS-702 @ 1.2 Kg/Sqm 3. Over hot bitumen, polymeric water proofing membrane consisting of 90 to 100 micron thick central core of HMHDPE film and standard weight 3 Kg/Sqm shall be laid with 100mm side lap/end lap on prepared surfaces as per manufacture’s instruction and strict supervision of manufacture’s technical representation complete all as specified and directed.

S & F in repairs sinks made of stainless steel 1mm thick kitchen or labortory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to ipe, overall size 485mm x 420mm bowl size 410mm x 3330mm x 160mm complete all as specified and directed.

S & F stainless steel plate rack made out of 1mm thick steel sheet of size 75cm x 90cm x 25cm (minimum weight 3.5 Kg) with fixing arrangement complete as per sample kept in GE`s Office suitable for officers quarters complete all as specified and as directed by Engineer-in-Charge.

M&L for painting to new steel surfaces of any description not otherwise described over 10cm wirdh or girth, with two coats of synthetic enamel paint (1st quality), over one coat of pink primer including preparation of surface complete all as specified

Demolition of Stone Laid, bedded and pointed in any mortar sett paving of any description of thickness complete all as specified and directed.

S&F Udaipur Green stone work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms and like on 15 mm thick screeding in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

S&F Udaipur Green stone work 18 to 20mm thick (table rubbed and polished) in riser, dado and like on 10 mm thick rendering in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

M&L Machine cut kota stone slab flooring 18-22mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L Kota stone slab 18-22mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

S&F Mild steel, plain black sheet 1.25mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

S & F mild steel framed work as in frames , doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410 -W(Gde E- 250) quality A complete all as specified and directed.

M&L for plain cement concrete 1:5:10 type E-2 ( using 40mm graded stone aggregate) as in filling of sunken floor including complete removal of existing treatment/material from sunken portion complete all as specified and as directed.

M&L for applying hot blown grade bitumen in two coats to plastered/concrete surfaces @ 1.5 Kg per Sqm per coat complete all as specified and as directed.

M&L for Loose filling with aggregates of gauge 40 to 80 mm brocken bricks in soakage pits, soakage wells, sunkan floor of toilets complete all as specified and directed.

M&L Welding in repairs n. exc 2.5cm in length Thickness of Metal to be welded n. exc 6mm complete all as specified and directed.

M&L Welding in repairs exc 2.5cm but n exc 5cm in length Thickness of Metal to be welded n. exc 6mm complete all as specified and directed.

M&L rounding to edges of stone slabs one edge, such as in steps,cooking platform, and other similar situations complete all as specified and directed.

SPECIAL ITEM (B/R)

M&L for one coat of synthetic enamel paint incl preparing old wooden surfaces exc 10 cm width or girth complete all as specified and directed.

Taking down shutter of any description exc 1 but n exc 2 sqm including easying , adjusting and refixing complete all as specified and directed.

M&L for applying two coats of polyurethene coating in sunken portion complete all as specified and directed.

PATHWAY

Demolition of cement concrete of any description and in any position as in floors/sunken floors complete all as specified and removal of demolished material to a distance exc. 2 KM but n.exc 2.5 KM complete all as specified and as directed.

M&L for plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of interlocking tiles complete all as specified and directed.

M&L for 60mm thick Machine pressed precast concrete interlocking paver block with grey cement and pigments any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade over and including 25 mm thick sand cushioning bed & sand filling between joints complete all as specified and directed.

M&L providing, cement concrete Type B0 1:2:4 (12.5 mm graded aggregate) in cement concrete in coping of mud stops, rounded or chamfered on edges complete all as specified and directed.

INTERNAL ELECTRIFICATIONS

Taking down old unserviceable copper/aluminium point wiring (light, fan, socket , power socket and bulk head fittings) on surface wiring on wooden batten/casings & caping complete, including fixture and fittings such as switches, ceiling roses,pendents holder, regulators, sockets and defective main switch/DB/MCB/Metal plug etc. by unscrewing carefully from boards etc and making good disturbed surfaces of walls complete all as specfied and directed.

M & L for point wiring for light/fan controlled by one switch with 1.5 sqmm single core 1100V grade FRLSH PVC insulated unsheathed multistranded copper conductor with and including PVC concealed conduit of medium grade with all fittings including MS pressed steel shet (1.0mm thick) sunk box with 3mm thick ISI marked laminated bakellite sheet fixed with cromium / nicckel plated screws and washers for switches and sockets, including 1.5 sqmm single core 1100v grade FRLSH PVC insulated unsheathed multistranded copper conductor as earth continuity conductor connected to common earth dolly and including cutting chases in walls / floors for concealed conduiting and making good disturbed surface area and white wash/colour wash to matching with the existing colour and all as specified and directed .

All as per srl item No 4.003 above but for call bell point complete all as specified and directed.

All as per srl item No 4.003 above but for 5 pin 5 amps socket outlet independent board complete all as specified and directed.

All as per srl item No 4.003 above but for 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed.

All as per srl item No 4.003 above but for one light point controlled by two Nos 2 way switches complete all as specified and directed.

S&F point wiring with electrolytic grade solid annealed copper conductor, jelly filled coaxial screened TV cable (category AL FOIL+ AL BRAND) with maximum signal loss 3.5 db/ 100 yards @ 100 Ghz) drawn in and incl concealed rigid PVC conduit medium grade of size 20 mm incl a pressed MS sheet (1.0mm thick) sunk box with 3mm thick ISI marked laminated bakellite sheet fixed with cromium / n ickel plated screws and washers to accommodate a TV socket complete including cutting of chases in wall/ floor and making good the disturbed surface as per adjoining surfaces all as specified and directed.

S&F TV socket complete all as specified and directed.

M&L for point wiring with 2.5 sqmm single core 1100v grade FRLSH PVC insulated unsheathed multistranded copper conductor with in and including PVC concealed conduit medium grade with all fittings including pressed MS sheet (1.0mm thick) sunken box with 3mm laminated bakellite sheet cover ISI marked suitable for an independant 6 pin 15/16 amps socket outlet ,including 2.5 sqmm single core 1100v grade FRLSH PVC insulated unsheathed multistranded copper conductor as earth continuity conductor connected to comman earth dolly including cutting chases in walls / floors for concealed conduiting and making good disturbed surface area to match with the adjoining surface all as specified and directed.

S&F switch piano flush type one way 5 amps SP 240 volts complete all as specified and directed.

S&F switch piano 2- way, 5/6 amps flush type 230 volts complete all as specified and directed.

S&F bell push flush type 5 amps SP 240 volts complete all as specified and directed.

S&F switch piano flush type one way 16 amps SP 240 volts complete all as specified and directed.

S&F socket outlet 2 in 1, 5 pin 5/6 amps flush type 240 volts complete all as specified and directed.

S&F socket outlet 2 in 1, 6 pin, 5 and 15 amps flush type 230 volts complete all as specified and directed.

S&F bell ding dong AC , 230 Volts, single pole complete all as specified and directed.

S&F Wall / surface mounted type LED light fitting batten type complete with LED lamp 9/10- watt (2 feet long), poly carbonate body and integrate electronic drive complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable complete all as specified and as directed. Make : - Orient Elecric ( Cat No : LBLN - 10 - C - SQ) Havells ( Cat No : LHEXBLP7IN1W009) Bajaj ( Cat No : BCLSB 10 WH) or equivalent model in list of Makes mentioned in tender

S&F ceiling rose 65 x 50mm three terminals complete all as specified and directed.

S&F ceiling fan regulator, electronic stepped type 5 stage speed regulation, ISI marked complete all as specified and directed.

Dismantling and taking down old serviceable LED tube light fitting of any type / capacity after necessary disconnection of electrical wires etc. and kept in safe custody and refixing the same after completion of B/R work at required places as specified and directed by Engr-in-Charge including connecting up with 3 core twisted flexible copper conductor cable complete all as specified and as directed.

S&F Wall/surface mounted type LED light fitting batten type complete with LED 1x 20 watt (4 feet long), extruded aluminium body with heat sink provided for efficient heat dissipation and integrate electronic drive complete with all accessories internally pre-wired and including connecting up with 3 core twisted flexible copper conductor cable complete all as specified and as directed. Make : - Orient Electric ( Cat No : LBLN - 20 - C - AL) Halonix ( Cat No : HLB - 03-20-CW-AL) Bajaj ( Cat No : BCLSBAL 20 W CW ) or equivalent model in list of Makes mentioned in tender

S&F Wall / surface mounted type LED light fitting batten type complete with LED lamp 05- watt white/coolwhite (1 feet long), poly carbonate body and integrate electronic drive complete with all accessories internally pre-wired and including connecting up with twine core twisted flexible copper conductor cable complete all as specified and as directed. Make :- Halonix ( cat No : HLB-07-05-CW) Havells (Cat No : LHEXBYPNIN1W005) Bajaj ( BCLSB05 WH) or equivalent model in list of Makes mentioned in tender.

S&F LED Street Light Fittings having Ingress Protection class minimum IP-65 , suitable for road lighting luminaire with high power LED and maintenance free system for capacity 35/36 W complete with 32 mm bore light grade GI pipe bracket (1.5m long) duly bent to shape including 2 Nos M.S. Flat (40mmx3mm) clamps, nuts, bolts, washers etc. all as specified and as directed. Make : - Havells ( Cat No : ENDURACITYLITEPLATPLUSSL35WLED757SASYBOPC) Halonix ( Cat No : HLSLD - 14-36 -CWL) Bajaj ( Cat No : BRTFG 36 W LED ) or equivalent model in list of Makes mentioned in tender.

S&F Decorative wall mounting light fittings with opal glass diffuser and chrome furnish/powder coated furnish suitable for and including LED Lamp 7-8 Watt all as specified and as directed. Make :- Philips (Cat No : 581851 Regalia) Havells (Cat pt No : LHFOAJD1TZ1T060) Halonix ( Cat No :HHW04913CF) or equivalent model in list of Makes mentioned in tender.

M&L for taking down carefully existing ceiling fan/exhaust fan from site before B/R repair work, keeping in safe custody in store for greasing / oiling of ball bearings / bushes and making it for smooth and noise free operation and painting with Hi-Gloss synthetic enamel paint of approved shade by spray painting after filling cavaties and re-fixing after providing new fan clamp, nuts/bolts, washers, down rod as required and provision of 3 core copper flexible cable of size 1.0 Sqmm from ceiling rose to fan connector complete with writing of MES No. on the fan surface all as specified and directed.

S&F air ventilating fan 250 mm sweep PVC body, AC, single phase, 230 volts, 1200 RPM complete with in-built louvers shutters and including PVC insulated 2 core 1.5 sqmm copper cable from ceiling rose to fan complete all as specified and directed.

Cutting walls of any type, making holes for fixing of exhaust fan any size or sweep and making good surface with fine plastering, finishing and colouring with existing colour matching complete all as specified and directed.

Dismantling and taking down old serviceable Energy Meters of any type / capacity after necessary disconnection of electrical wires etc. and marking the Quarter No on each meters with parmanent marker pen and keeping in safe custody for re-fixing /reconnection in new meter cabinet all as specified and as directed.

Supply, install, testing & commissioning of Indoor type, wall mounted (with anchor bolts & nuts) compartmentalized type Meter Cabinet of overall dimension 1200mm (W) x 1000mm (H) x 250mm (D) made out of 2.0 mm thick CRCA SS Sheet with front door having cutout duly covered with transparent polycarbonate / glass panel for viewing KWh meter and other doors shall be opeque. All doors should have gasket and locking arrangement to meet minimum ingress protection level IP-43.The cabinet shall be painted both internally and externally with powder coated paint (RAL 7032 : SIEMENS GREY) after necessary surface treatment. The cabinet shall be fabricated as per the drawing and comprising of following accessories :- a) Four pole MCCB, 40 Amps with breaking capacity 16 KA having fixed thermal and fixed magnetic release and spreader link at both incoming and outgoing side.- 01 No. b) Aluminium Bus Bar of size 25mm x 3mm duly mounted on FRP / DMC insulators and necessary drilling for 1 incoming & minimum 08 outgoing connections and duly covered with heat shrinkable PVC sleeve of standard colour code - 04 Nos. c) MCB DP 32 Amps, 10 KA - 04 Nos ( To be connected with 04 Nos Meters) d) MCB SPN 06 Amps, 10 KA - 01 No (For Common lighting + Bldg Security Lights) e) LED indicating Lamps, 22mm with 3 Amps SP MCB - 03 Nos. f) 3 Way bakellite strip type cable connector 30 Amps rating - 06 Nos g) Dial type DIN rail mounting, Analog Time Switch 16 Amp / 230V AC 50 Hz, with battery back up, 24 Hrs programmable type with 1 NO & 1 NC output contact- 01 No (for common lighting). h) Internal wiring with 1100V grade FRLSH PVC insulated multiflexible copper wire duly crimped with copper lugs all as mentioned below :- i) MCCB to Bus Bar - 16.0 Sqmm ii) Bus Bar to Cable Connector via KWh meter and MCB - 6.0 Sqmm iii) Bus Bar to LED Lamp/ Time switch via MCB - 1.5 Sqmm Note : Existing meters, as dismantled under item No 4.029 above, will have to re-fixed in this new meter cabinet including all necessary electrical connection.

Taking down distribution board of any type including cutout, MCBs etc.complete all as specified and as directed.

Supply and fix in replacement of sheet metal enclosure distribution board, single pole and neutral, AC, 240 volt, 08 way, double door with 100 Amp rated copper bus bar and metal door with minimum IP - 43 and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

S & F MCB single pole 240 volts, 'B' curve of rating from 6 to 32 amps, with rupturing capacity 10 KA,including providing thimble for out going cables.

S & F MCB DP 240 volts, 'B' curve of rating from 32 amps, with rupturing capacity 10 KA, including providing thimble for out going cables.

M&L for submain wiring with two single core 1100 v grade FRLSH PVC insulated flexible copper conductor cable of size 4 sqmm and one single core PVC insulated FRLSH flexible copper conductor cable green colour of size 4 Sqmm as earth lead in & including a separate concealed PVC conduit medium grade, ISI mark of dia not less than 25mm including cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with adjoining surfaces including Taking down old unsv sub main wiring any type and size aluminium/ copper incl batten/ conduit and making good disturbed surface to match with existing complete all as specified and directed.

S&F of water heater storage type 25 Ltrs, Electrically operated, 5 star rating with ABS/Steel body and stainless steel inner tank duly insulated with PUF insulation and heating element of 2 KW complete with all accessories such as safety valve, thermostate, NRV, PVC connection etc complete all as specified and directed. Make : - Havells (Cat No :GHWAMGTWH025) Bajaj (Montaga) Venus ( Audra) or equivalent model in list of Makes mentioned in tender.

S&F concealed type GI Sheet enclousure for switches / sockets etc. complete with a 25 Amps modular type motor starter (2 Module) with one SPN 'Ç'curve MCB of capacity 25 Amps (2 Module) & a 20 Amps 3 pin socket (2 module) including electrical connections all as specified and directed by Engr-in-charge. (For Air Conditioners)

M&L for earthing complete with galvanised steel plate electrode 600mm x 600mm x 6mm thick buried directly in ground (earth pit not less than 2.25 Mts deep below ground level with top edge of the plate not less than 1.50 Mtrs below ground level connected to glavanised iron Wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanised iron or steel connected to earthing test point all as specified incl 15 mm GI tubing medium grade and necessary fitting for protection of GI wire incl laying of charcoal dust and common salt in alternate layer, PCC Pit (1:3:6) type C-1 using 20 mm graded stone aggregate, RCC cover 40mm thick (1:2:4) type B-0 using 12.5mm graded stone aggregate reinforced with 6 mm dia round bar @ 75mm C/C both ways with MS handle 8mm dia, plastering 15mm thick CM (1:6) externally upto 150mm below ground level , GI funnel with 20mm dia medium grade GI pipe for watering and wire mesh incl excavation and earth work and disposal of surplus soil complete all as specified and shown on electrical plate No 3 of SSR Part (2009) and connected to earth test point incl testing and marking Bldg Nos and writing Test Results on a 3.0mm thick painted M.S. earth pit marking Plate (200mm x 100mm) duly welded with a 450mm long 10mm dia round M.S. rod, fixed with the earth pit chamber by grouting complete including taking out old unserviceable earthing system including demolishing with old earth pit chambers and removing of debris from the site with levelling the ground all as specified an directed.

Supply and fixing Wall Fan high speed, 400 mm sweep,220-240 volts, AC, 50 Hz 1400, ± 50 rpm three blades with pull cord for on/off,speed setting and osillation on/off , air delivery not less than 56 CMM, power consumption not more than 70 watt complete all as specified and directed.

EXTERNAL ELECTRIFICATION

Excavation in trenches n.exc 1.5mtr wide and not exc 1.5mtr depth and getting out in soft/loose soil including brick protection cover of LT Cables etc complete all as specified and as directed.

Taking up old U/S LT UG cable of size between 10 - 16 Sqmm 2 core including protection bricks, stacking serviceable for reuse complete all as specified and as directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and as directed.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 sq mm 4 core, complete all as specified and as directed.

Making horizontal bore hole under road suitable for 80mm bore size at the depth not less than 1 Mtr below ground level for passing of LT underground cable complete all as specfied and as directed.

Material and labour for providing sand cushioning with dry fine sand including filling, spreading, levelling in layers in cable trench with approved quality of sand for protection of under ground cable complete all as specified and directed.

M&L for Brick, sub class ‘B’, old size, laid in trenches as in cable protection complete all as specified and as directed.

Laying only old serviceable brick , as obtained from item No. 5.003 above for protection of cables, laid perpendicular to the axis of the cable all as specified and as directed.

Removing surplus excavated materials n.exc.50mtr and depositing where directed at level n.exc 1.5 mtr above the starting point complete all as specified and directed

Materail and labour for GI tubing light grade of 40 mm dia for cable protection on pole/wall/floor/ or in trenches and drain etc complete with necessary clamp, nut, bolts and washers and socket and making good the disturbed surface of wall , floor or roof etc all as specified and directed.

Deduct Schedule of Credit Rs (-) 1108372.00

TEAM ACC INFRABUILD PRIVATE LIMITED

M/s Arihant Builders

Sudhir Sharma Associates

Shree Construction Co.

VEE SONS BUILDERS PVT LTD

J.D.Builders