PROVN OF PARKING SHED FOR TWO WHEELERS AND CERTAIN MINOR WORKS AT IMA DEHRADUN

Amount

Demolition of brick or stone masonary built in cement mortar including pre cast articles complete all as specified & directed.

Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified & directed.

Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above) ground level complete all as specified & directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 Sqm on plan and n' exc. 1.5 m in depth and getting out in any type soil complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified & directed.

Excavation in post holes each n.exc 0.5 cum and getting out & removing surplus soil to a distance n.exc 50m & making good surface in any type soil complete all as specified & directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in soil complete all as specified & directed.

Removing surplus excavated soil to a distance n.exc 50 metre & depositing where directed at a level n.exc 1.5 metre above the starting point complete all as specified & directed.

PCC 1:3:6 typeC-2 using 40mm graded crushed stone aggregate as in foundation filling, mass concrete and sub base of floor etc complete all as specified and directed.

PCC 1:2:4 type B-2 using 40mm graded crushed stone aggregate as in foundation filling, mass concrete etc complete all as specified and directed.

PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation filling, mass concrete and sub base of floor etc complete all as specified and directed.

75mm thick Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor etc complete all as specified and directed.

100mm thick Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base etc complete all as specified and directed.

75mm thick Cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in sub base etc complete all as specified and directed.

PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in coping, benching, cills, pcc gola, holdfast and the like including weathering, slightly rounded or chamfered angles and throating, including necessary from work etc complete all as directed

PCC 1:5:10 type E2 (using 40 mm graded crushed stone aggregate) as in foundation or sub base etc complete all as directed

75mm thick PCC 1:3:6 type C-2 using 40 mm graded crushed stone aggregate as in plinth protection or similar places, and finishing the surface even and smooth without using extra cement including making joints 12mm wide to the full depth of PCC at every 3 meters and at every change of direction and filling the same with sealing compound grade 'A' including necessary formwork etc and including demolition of existing old cement concrete in ground floors and pavings n.exc 15cm thickness (below or above) ground level complete all as specified and directed

Brick work with fly ash’ bricks straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed.

Brick work with fly ash bricks (old size), straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as directed.

15mm bore medium grade steel water tubing, galvanized (ISI Marked) with and including all fittings (ISI Marked) and jointed, tested and fixed complete to wall and ceiling or laid in floors etc complete all as specified and directed.

20 mm bore medium grade steel water tubing, galvanized (ISI Marked) with and including all fittings (ISI Marked) and jointed, tested and fixed complete to wall and ceiling or laid in floors etc complete all as specified and directed.

PVC (SWR) bends any radius 75 mm bore complete all as specified and directed

PVC (SWR) bends any radius 110 mm bore complete all as specified and directed

PVC (SWR) junction single (single T ) equal or unequal 75 mm bore with access door complete all as specified and directed

PVC (SWR) junction single (single T ) equal or unequal 110 mm bore with access door complete all as specified and directed

110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/trenches with MS clamp etc complete all as directed.

75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/trenches with MS clamp etc complete all as directed.

Vitreous china, white, wash hand basin, flat back size 550x400mm 'including MS brackets including cutting for and pinning in, but including PVC (LDPE) waste pipe & 450 long 15mm PVC connection complete all as specified and directed.

15mm bore short body fancy type bib tap chromium plated complete all as directed Make- Jaguar ESSCO cat part No MQT-511 or equivalent of Cera/Hindware

500 Litres capacity rotational moulded polyethylene water storage tanks, three layered, ISI Marked (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-2009 including 20mm dia GI light grade washout pipe 50mm long with plug and 20mm dia GI light grade over flow pipe 600mm long with fitting complete all as specified and directed

15mm bore stop cock chromium plated male end complete all as specified and directed Make- Jaguar ESSCO cat part No MQT-513A or equivalent of Cera/Hindware

20mm bore stp valve cast copper alloy screwed down high pressure with cructh butter fly handle screwed both end for iron pipe or for union of 15mm bore pipe complete all as specified and directed

Non skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, laid in floors over a layer of JK cement tilemax adhesive including grouting as per manufacturers instruction complete all as specified and directed.

Glazed ceramic coloured tiles of size 300 mm x 200 mm x 7mm thick, as in vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tile with and including 10 mm thick rendering in cement mortar 1:4 finished rough complete all as directed

Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed

Non skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) aas in vertical surfaces such as dado, skirt etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with and including of 10 mm thick in CM 1:4 finished rough complete including dismantling existing tile complete all as specified & directed.

Chequered cement tiles 25 cm x 25 cm x 22 mm thick , set and jointed in neat cement slurry in floor with grey cement mixed with colour pigment with and including laying of 20 mm thick screed bed or bedding layer in CM 1:6 complete all as specified & directed.

Machine cut kota stone slab flooring 18-20mm thick over and including 20mm thick cement sand screed in CM (1:4) as base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing complete all as directed.

Rendering 15mm thick plaster on fair faces of brick work or concrete surface in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed

Rendering 15mm thick plaster on other than fair faces of brick work or concrete surface in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed

10mm thick rendering on concrete surfaces in CM 1:3, surface finished even and smooth as in ceiling etc complete all as specified & directed.

Pre- painted galvalume aluminium Zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and directed

Pre- painted galvalume aluminium Zinc coating GI based profile steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall/ ridges, fixed with self tapping screws etc complete all as specified and directed

Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed.

Preparation of new steel surfaces of any description n exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed.

Preparing new or previously untreated surface of wall and applying three coats of white wash complete all as specified & directed.

Liquid soap container of PTMT fixed with and including chromium plated brass screws and wooden plastic cleats complete all as specified and directed.

Use & waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick for fair finish surface complete all as directed.

R.C.C 1:1.5:3 using using 20mm graded crushed stone aggregate as in slab supported on walls beams and columns in floor, roof, landing and in shelves and the like complete all as specified & directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed.

Mild steel plates (plain or chequered ) channels square cut or notched (ordinary or counter sunk forming holes with rveted bolts or welded attachment complete all as specified & directed.

Mild Steel tubular work as in vertical post including special shaped washer etc. complete using ERW or induction butt welded tubes complete all as specified & directed.

Mild Steel tubular work as tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes including MS nuts and bolts incl all necessary drilling bolting or riveting or welding etc complete all as specified & directed.

Rolled mild steel work as in main and cross beams, hips and jack rafters, purlins where connected to common rafters and running rails and guids for sliding doors fixed with connecting plate or other connected plates etc. Complete all as specified & directed.

Rolled mild steel work as in roof trusses (framed), trussed, purlin crane gantries, rails and fastenings etc including distance pieces plates cleats etc complete all as specified & directed.

Rolled mild steel Joist channel, angle or tee seciton, fixed independetly without connecting plates etc complete all as specified and directed

Mild Steel bolts 16 to 20 mm dia (machine made ) with hexagonal or squre head at one end and screwed the other or screwed both ends to be fitted with washers and one hexagonal or squre nuts exc 15 cm and n exc 22.5 cm long complete all as specified and directed.

Mild Steel bolts 5 to 10 mm dia (machine made ) with hexagonal or squre head at one end and screwed the other or screwed both ends to be fitted with washers and one hexagonal or squre nuts exc 5cm nex 10cm cm long complete all as specified and directed.

Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering running rails and guides) and hanging; also fastening and fixing complete all as specified & directed.

Mild steel framed work such as grills, grating etc with end of bars shouldered and/ or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing framed work of water tanks and similar work including pintal hinges, stops hand made sliding bolts etc complete all as specified & directed.

Mild steel works as in bands, straps, hold fast, wall/wind ties, angle cleats and similar small articles etc complete all as specified & directed.

75 mm thick PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in floor finished even and smooth with using extra cement laid in alternate panel complete all as specified and directed.

Hard core of broken stone/boulder of gauge.exc 63mm but n exc100 mm deposited spread and levelled in layer n.exc 15cm thick watered and rammed to a true surface complete all as directed.

Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners brass handles etc as specified in clause 10.24 of SSR Part-I, and errected in position and securing runners with holdfasts and brackets complete all as specified and directed

Sand filling under floors or in foundations including watering and consilidation complete all as specified and directed

1.6mm thick mild steel plain black sheet in wall cladding steel gates and similar work cut to size holes punched including round headed screws clout nails or riverts and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams including bending or turning up mitered angles etc as required complete all as specified and directed

25mm mesh of wire netting of galvanised steel wire 1.40 mm dia fixed with tinned tack of wire staples complete all as specified and directed

Granite (of any type) 12-16mm thick machine cut in skirting / dado (Gate pillar) laid over cement 15mm thick rendering in CM 1:4 jointed with coloured cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including and polishing of type complete all as specified and directed

Sink made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilver brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330 mm x 160mm complete all as specified and directed

Cast iron floor trap, sand cast 75mm bore outlet with brass chromium plated grating including jointing to waste pipe in run lead completed all as specified and directed

PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in surface channels and drains etc complete all as specified & directed.

Extra forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms, moulds mitered/stopped ends complete all as specified and directed

Waste coupling 32mm dia brass chromium plated for sinks basins etc with long screwed shanks and fly nuts, flange end bedded in red lead cement including PVC flexible pipe with cup suitable for 32mm dia waste coupling complete all as specified and directed

Granite (of any type) 18-20mm thick machine cut beded over 20mm thick screeding in CM 1:4 jointed with Grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including polishing complete all as specified and directed

15mm bore long body bib tap chromiumm plated with wall flange complete all as specified and directed Make- Jaguar ESSCO Cat part No MQT-512 or equivalent of Cera/Hindware

Stop valves of cast copper alloy fancy type 15mm bore screwed down high pressure with crutch or butter fly handle complete all as specified and directed

Cast iron floor trap, 100mm bore outlet with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4)

15 mm bore pillar cock chromium plated rocket type Aerator complete all as specified and directed. Make- Jaguar ESSCO Cat part No MQT-507 or equivalent of Cera/Hindware

M/S RAJESH KUMAR GOYAL

VERDHMAN ASSOCIATES

Sharda Enterprises

M/s caspur construction company

M/s RK ENTERPRISES