REPAIR MAINT OF PLINTH PROTECTION HARD STANDING CHAJJAS REPAIR ETC OF AGE B/R-II UNDER GE R OORKEE

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for and including reinforcement required to facilitate demolition upto and including fourth story and on the roof top/mumty/parapet and removal of debris and rubbish out side MoD land complete all as specified and directed.

M&L for PCC (1:3:6) type C-1 (20 mm graded aggregate) as in copping, surface channel, benching of manhole/drain etc slightly rounded or chamfered angles and throating, as directed incl finish the surfaces smooth without using extra cement complete all as specified and directed.

M&L 75mm thick Cement concrete type D-2, (1:4:8) (40mm graded aggregate) as in sub base in floor etc. complete all as specified and directed

M&L Cement Concrete 1:3:6 (20mm graded aggregate), 75mm thick as in Plinth Protection/Foot Path/hardstanding etc, finishing Concrete Surfaces Even and Smooth without using Extra Cement, complete all as specified and directed.

Supply only of glass dividing strips, 3mm thick and inserted in position, width of strip 38 mm complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls etc including racking out joints, hacking for keys, scrubbing down with water etc complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:4) using coarse sand on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 5mm thick plastering in cement mortar (1:3) as in ceiling finished even and smooth without using extra cement to match with existing surface complete all as specified and directed.

M&L for Preparing newly plastered surfaces of walls and applying two coats of OBD over a coat of primer incl 1 mm thick layer of wall care putty to obtain smooth finish complete all as specified and as directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over new surfaces of wall/ceiling of projection/ chajja, including 1 mm thick putty of approved make all as specified and prescribed by manufacture of paint and as directed at site by Engineer-in-Charge. Note:- (i) The work must be got executed through authorised applicator of manufacture after concluding an MoU with manufacture for company back guarantee by the contractor. The authorised applicator of manufacture shall be got approved from GE before commencement of work.

M&L for three coats of white wash on walls including preparation of new surfaces complete all as specified and directed.

M&L for complete removal of existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces and applying two coats of oil bound distemper, over and including a coat of 1 mm thick wall care putty with preparation of plastered surfaces complete all as specified and directed.

M&L for preparing old decorated plastered surfaces of wall including cornices, pilastered etc by brooming down or steel wire brushing, scraping down existing colour surface smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots and applying one coat of oil bound distemper (approved colour/shade) complete all as specified and directed.

M&L for preparation of old painted surface of wood and wood based surfaces by knotting, stopping etc of any description exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted steel and iron surfaces of any description exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Demolition stone slabs and tiles of any description or thickness in floors, aprons laid bedded and jointed in any mortar etc complete all as specified and directed.

M&L for pavement parking ceramic tile (min size 300x300 mm) and 8 to 10 mm thick set and jointed in neat cement slurry and pointed in coloured cement to match laid over 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for precast machine pressed cement concrete interlocking paver blocks of any shape and size confirming to IS 15658-2006 of 60 mm thick M-35 grade, glossy type with grey cement and pigment laid dry over and including a layer of 25 mm thick sand cushioning complete all as specified and directed (Note :- Rate quoted by contractor inclusive of sand cushion).

M&L for providing reinforced cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in Chajjas complete all as specified and directed Note WPC To be Paid Separtely.

Supply only liquid integral water proofing compound (ISI Marked)

Use & waste form work to sides and soffits of shelves etc including supports such as kitchen shelves, platforms and similar works rough finish surface of concrete (the thickness of slab/shelves n.exc.100 mm) complete all as specified and directed.

Use & waste form work to chullah hoods, chajjas, troughs and similar items for rough finish including edges complete all as specified and directed

M&L for preparing plastered new surfaces of wall and applying one coat priming and applying two coat of cement paint complete all as specified and directed.

Demolition of brick work in built in cement mortar for cracked wall of compound wall and similar work complete all as specified & as directed.

Dismantling Bricks (laid Flat in Floor or laid on Side Walls of Brick Drains, Channels), etc, Bricks laid, bedded and pointed in any Cement Mortar, complete all as specified and as directed.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6 meter mean radius with old size bricks built in CM (1:6), complete all as specified & as directed.

M&L Brick work with sub-class ‘B’ bricks in brick-on-edge walls (less than ½ brick thick), built in cement mortar (1:4) complete all as specified & as directed.

M&L Brick Work with old size Sub-Class ‘B’ Bricks, laid on Edge as Side Walls of Brick Drains in Slope, Bedded and Jointed in Cement Mortar (1:6) and Pointed in Cement Mortar 1:3, complete all as specified and as directed.

M&L PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundation of manholes, drains etc complete all as specified and directed

Cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 or 3/4 section) in cement concrete (1:2:4) type B1 using 20 mm graded stone aggregate finished smooth and reforming benching as required for 100/150mm dia pipes complete all as specified and directed.

Dismantling of Cast Iron pipe/PVC pipe up to 75 mm bore complete all as specified and directed.

S&F PVC (SWR) pipes of 75 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.80 mm) single socketed in any length with rubber ring joints including all fittings/ fixtures fixed on wall or in trenches or in floor complete all as specified and directed.

S&F PVC (SWR) 75mm dia (single T) or unequal provided with access door complete all as specified and directed.

S&F in repair PVC (SWR) floor trap, 75mm dia plain including jointing with solvent cement with grating including jointing to waste pipe in cement concrete complete all as specified and directed.

S&F in repair PVC branch piece single (equal or unequal) 75 mm bore ordinary or inverted (spigot or socket type) or with parallel branches incl access door complete all as specified and directed

S& F PVC (SWR) vent cowl suitable for 75 mm pipe complete all as specified and directed.

S&F PVC (SWR) 75mm dia (Double T) or unequal provided with access door complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends/shoes any radius complete all as specified and directed

S&F in repair 75 mm pipe stack clamps out of 50mmx 5 mm flat iron including bolts and nuts and securing ends of stays to walls or roof complete all as specified and directed.

Dismantling of Cast Iron pipe/RCC drain pipe/PVC pipe up to 110 mm bore complete all as specified and directed.

S&F PVC (SWR) pipes of 110 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.80 mm) single socketed in any length with rubber ring joints including all fittings/ fixtures fixed on wall or in trenches or in floor complete all as specified and directed.

S&F PVC (SWR) junction, 110mm dia (double T) or unequal provided with access door complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends/shoes any radius complete all as specified and directed

S&F in repair PVC branch piece single (equal or unequal) 110 mm bore ordinary or inverted (spigot or socket type) or with parallel branches incl access door a complete all as specified and directed

S&F PVC (SWR) junction, 110mm dia (Single T) or unequal provided with access door complete all as specified and directed.

S&F PVC (SWR) reducers 110mm dia, complete all as specified and directed.

S&F in repair 110 mm pipe stack clamps out of 50mmx 5 mm flat iron including bolts and nuts and securing ends of stays to walls or roof complete all as specified and directed.

Ditto all as per item No 49.00 above but for 75mm bore (dia).

S&F in repair 75mm PVC (SWR) floor trap with grating including jointing with solvent cement including dismentling of old one and making the surface good complete all as specified and directed.

S&F in repair (SWR) junction single, (single 'T') 110mm bore equal or unequal complete all as specified and directed.

S&F in repair (SWR) junction single, (single 'T') 75mm bore equal or unequal complete all as specified and directed.

S&F in repair 75mm PVC (SWR) branch piece, single (single Y) equal or unequal provided with access door complete all as specified and directed.

S&F in repair 110mm PVC (SWR) branch piece, single (single Y) equal or unequal provided with access door complete all as specified and directed.

S&F in repair 75mm PVC (SWR) vent cowl complete all as specified and directed.

S&F in repair 100 mm PVC (SWR) vent cowl complete all as specified and directed.

Demolition of reinforced cement concrete as in cover slabs of manhole or septic tank, soak pit, RCC slab etc all as complete all as specified & as directed.

M&L for RCC 1:2:4, type B1(using 20mm graded aggregate) Precast cement concrete as in cover slab for man hole, or septic tank, soak pit,chamber cover, RCC slab etc and similar article with plain face. Set in cement mortar (1:4) complete with MS Frame all as specified & as directed.

S&F deformed or twisted TMT bar 8 mm dia cut to length, bent to shape required, incl cranking bending and binding with MS wire (annealed) not less than 0.9mm or securing with clips complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi corrugated etc), CGI sheets in roof covering complete as specified and directed by Engr-in-Charge

S&F Prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm (AZ-150) thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Prepainted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm (AZ-150) thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and as directed by engineer in charge.

M&L for MS rolled joist, channel, angle, or tee sections, fixed independently, with connecting plates, etc using Fe 410-W Gde E-250 Qlty-A (cut to ordinary lengths i.e within 20mm of the length indicated) complete all as specified and as directed.

M&L for cutting of bushes small trees (Peepal small plants etc) trunks shrubs of any dia and girth from roof projection, chajjas, wall junction parapet etc at any height by necessary demoliton of brick work etc if requried and making good distrubed surfaces to match with existing finihes with and incl material and labore in CM (1:4) mixed with WPC/PCC (1:3:6) type B0/Bk work in CM (1:4) as required at site complete all as specified and directed.

M&L for cutting hole of 230x230x230mm in walls, filling with PCC (1:2:4) Ty B-1 using 12.5mm thick stone aggregate incl fixing of 1Nos angle iron of size 50mmx50mm x6mm, 1m long each incl running welding with other angle, incl 2 coat of synthetic enamal paint over a coat of primer over exposed steel surfaces for cooler stand, complete all as specified and directed

AMARJEET SINGH AND CO. (BID ID -3502224)

RAM PRAKASH & ASSOCIATES (BID ID -3502447)

M/S GIRI CONSTRUCTION CO. (BID ID -3502043)

AKANSHA.ASSOCIATES (BID ID -3502918)