SPL REPAIR TO 04 X OR MD ACCN QTR NO P-22, P-23, P-284 AND P-290 OF 9 JAT AND BLDG NO T-16 AND T-16 BARRACK (SANITARY ANNEXES) OF 288 MED REGT UNDER GE ROORKEE

Amount

Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for and including reinforcement required to facilitate demolition upto and including fourth story and on the roof top/ mumty/ parapet/ Chimney and removal of debris and rubbish out side MoD land complete all as specified and directed.

M&L for mild steel TMT bars of 10 mm dia and over cut to length bent to shape required including cranking, bending etc and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for reinforced cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in kitchen slab complete all as specified and directed

Form work to sides and soffits of shelves etc including supports such as kitchen shelves, platforms and similar works rough finish surface of concrete (the thickness of slab/shelves n.exc.100mm) complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness (below or above ground level) including removal of rubbish out side complex (MOD land), complete all as specified and directed.

M&L 75mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone agg). Plinth protection laid to a slope of 1 in 24 in alternate basis system. Each bay shall not exceed 3m in length 12mm wide & 75mm deep joint shall be formed between the bays which shall be filled with mastic filling to full depth comprising a mixture of 1 part of hot blow bitumen 85/25 portion and two parts of heated badrapur sand (by volume) etc complete all as specified and directed.

M&L Cement concrete 1:2:4 type B0 (using 12.5mm graded crushed stone agg) as in roof leveling, finished even and fair, complete all as specified and directed

M&L for PCC (1:2:4) Ty B-0 using 12.5mm thick course aggregate as in cills, steps, parapets, copings, and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed

M&L for 75mm thick PCC (1:4:8) ty D-2 using 40mm graded stone aggregates as in levelling course below floor tiles in bathroom and WC and path etc.

Supply and laying sand (20 mm thickness) for cushioning to interlocking paver block complete all as specified and directed.

M&L for 60 mm thick Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of M-35 Grade made with grey cement and pigment complete all as specified and directed

Demolition of brick work built in cement mortar in any description and position complete all as specified and directed.

M & L brick work with sub class "B" bricks straight or curved on plan exc 6 m mean radis built in CM 1:6 complete all as specified and directed.

M&L for Brick work with sub clas "B" bricks straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified and directed.

Dismantling of Cast Iron pipe/ RCC drain pipe/PVC pipe up to 150 mm bore complete all as specified and directed.

S&F PVC (SWR) pipes of 110 mm nominal outside diameter single socketed in any length with rubber ring joints including all fittings/fixtures fixed on wall or in trenches or in floor complete all as specified and directed.

All as per item No. 16 above but 75mm nominal outside diameter.

S& F PVC (SWR) vent cowl suitable for 75 mm pipe complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends/shoes any radius complete all as specified and directed

All as per item No. 19 above but 75 mm bore.

S&F in repair PVC (SWR) floor trap/Nahani trap, 75mm dia plain including jointing with solvent cement with grating including jointing to waste pipe in cement concrete complete all as specified and directed.

S&F in repair PVC branch piece single (equal or unequal) 110 mm bore ordinary or inverted (spigot or socket type) or with parallel branches incl access door a complete all as specified and directed

S&F PVC (SWR) reducers 75mm dia, complete all as specified and directed.

S&F in repair 110 mm pipe stack clamps out of 50mmx 5 mm flat iron including bolts and nuts and securing ends of stays to walls or roof complete all as specified and directed.

All as per item No. 24 above but 75 mm bore pipe.

S&F PVC (SWR) junction, 110mm dia (Single T) or unequal provided with access door complete all as specified and directed.

Cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 or 3/4 section ) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate finished smooth and reforming benching as required for 100/150mm dia pipes complete all as specified and directed.

M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and incl 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for joint free coloured glazed ceramic tiles in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick rendering in CM 1:4 complete all as specified and directed.

S&F Vitrified tiles coloured of 7 to 8 mm (squre/ rectungular ) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors set and jointed in neat cement slurry and pointed with white or coloured cement over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

S&F Vitrified tiles coloured of 7 to 8 mm (squre/ rectungular ) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in skirting, dado etc set and jointed in neat cement slurry and pointed with white or coloured cement over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M & L for 16-18 mm thick mirror polished Machine cut kota single piece stone slab of size 22''x22'' for flooring over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab laid over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L kota stone mirror polished slab with uniform texture of 16-18 mm thick in trader of steps (to be flushed and provided with three Nos of grooves at the end on each step), riser of steps, skirting, dado and pillars in one single piece (size decided by Engineer-in-Charge) laid over and including cement screed 10mm thick in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, bevelled edge of corner etc complete all as specified and directed.

M & L for granite 18-20 mm thick (table rubbed and polished) in cooking platforms and laid over cement screed mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl moulding of front side if required at site complete all as specified and directed.

Dismantling of any type of tiles or terracing tiles, single layer on roofs, kerbs, aprons, floor etc and removal of rubbish out of defence land complete all as specified and directed.

Demolition of Mud Phuska in roofs,any thickness including plastering and leeping of any thickness upto 30cm deep complete all as specified and directed.

M&L for 40mm thick brick tiles laid on 15mm thick cement mortar (1:6) and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on RCC surface complete complete all as specified and directed.

M&L for rendering 20 mm thick cement plaster in CM (1:3) finished even and smooth w/o using extra cement and using waterproofing compound on fair faces of brick work or concrete surfaces. (Note : WPC will be measured and paid for separately.)

Taking down old existing water proofing treatment from the top of RCC / arch slab, cleaning with water and disposal of rubbish off the premises complete all as specified and directed

Material & labour for cleaning of concrete or plastered surfaces of roof and applying priming coat using with bituminous primer @ 0.30kg per Sqm followed evenly by a tack coat @ 1.20 kg per Sqm using 85/25 grade industrial hot blown bitumen, over it laid with 2mm thick APP modified polymeric water proofing membrane weight 3.0 Kg per Sqm reinforced with non-woven polyester fabric (weight not less than 160 Gm per Sqm) unrolled & bonded to substrate with side and end laps 75mm & 100mm as per manufacturer’s instruction and applying over it a tack coat using 85/25 grade industrial hot blown bitumen @ 1.20 kg per Sqm and finally finished the top of polymeric water proofing membrane complete all as specified & directed.

Taking down chowkhat or frames exc. 1.5 Sqm and n.exc 4 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Taking down chowkhat or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Taking down shutter only exc 1 Sqm but not exc 2 Sqm each complete all as specified and directed.

Supply & fixing factory made pressed steel frames for doors with one or more rebates including necessary fitting lugs, hinges, lock strike plates etc completed size of frame 165x60mm made out of 1.25mm MS sheets including PCC 1:2:4 Ty B0 using 12.5mm graded stone aggregate as in frame complete all as specified & directed.

Supply & fixing factory made pressed steel frames for doors with one or more rebates including necessary fitting lugs, hinges, lock strike plates etc completed size of frame 105x60mm made out of 1.25mm MS sheets including PCC 1:2:4 Ty B0 using 12.5mm graded stone aggregate as in frame complete all as specified & directed.

Cutting holes in brick walls exc half bk wall but n exc one bk wall built in cement mortar or cement lime mortar and stone walls built in lime mortar or for inserting holdfasts and making good dismantalled portion in CM (1:3) or cement concrete (1:2:4) type B1 as required.

S&F M.S work as in holdfasts, wind ties , plane angle cleats for securing purlins to wooden trusses or rafters etc complete all as specified and directed..

S&F factory made steel shutter shall be made out of angle iron 35x35x5mm and 3 nos 25x25x3mm as cross support in frame of door and covered with 1.00mm thick MS sheet, running welding with frame, with locking arrangement complete all as specified and directed

S&F 35mm thick factory made Glazed and skeleton shutters using second class hard wood, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and directed.

M&L for built in steel cup board with pressed steel frame of size 75 mmx45mmx1.25 mm thick with pressed steel shutter 1mm th Godrej pattern fixed to masonry wall by hold fast made out of 25x3 mm flat iron including MS hanging rod of 10 mm dia with bracket fixed on inner side of one leaf of shutter and on other leaf provision of MS peg set of 3 pegs including spray including locking arrangement complete all as specified and directed.

S&F factory made gauged shutter shall be made out of angle iron 35x35x5mm (outer frame) and 25x25x5mm (middle rail 2 nos, 150 mm apart from each other) and 1.0mm thick steel sheet covering on middle rail, 10mm Square bars @ 100mm C/C fixed vertical as grill complete with stainless steel fly proof wire mesh having 0.63mm nominal dia wire and 1.4mm average with aperture, with locking arrangement complete all as specified and directed

S&F Fiber glass reinforced plastic (FRP) Flush door in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameter of FRP, laminate confirming to table 3 of IS -14856 complete all as specified and directed

S&F FRP door frames three legged of cross section 90x45mm having single rebate 32mmx15mm. The laminated door frame moulded with fire retardant grade unsaturated polyester resin and chopped mat. Door frame laminated shall be 2mm thick, frame shall be covered with fiber glass from all sides MS flat iron 25x3mm shall be provided at the bottom to steady the frame including PCC 1:2:4 Ty B0 using 12.5mm graded stone aggregate as in frame, complete all as specified and directed.

S&F 100 mm long (size) butt hinges, stainless steel AISI 304 grade with brass/bronze hinge pin, complete all as specified and directed.

All as per item No. 55 above but 75 mm long.

S&F 300mm long, stainless steel of AISI 304 grade, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts complete all as specified and directed.

S&F Stainless steel of AISI-304 grade barrel tower bolt 200 mm long, extruded section complete all as specified and directed.

All as per item No. 58 above but 100 mm long.

S&F stainless steel handles, fabricated type, anodised of size 150mm size long complete all as specified and directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor of 140mm long complete all as specified and directed.

M&L Preparation of new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L Preparation of new or previously untreated steel and steel based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L powder coated of 50 micron anodised aluminium frame for doors, windows, ventilators, partition walls etc with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F powder coated (minimum thichness of powder coating 50 micron) aluminum anodized window sliding type (03 shutter type) with sash bars, aluminum section weighting 0.55 kg/m (min) for shutter including necessary joining cleats, glazing clips, rubber packing, anodized aluminum fittings and including S&F stainless steel wire mesh 0.36 mm nominal dia of wire & average width of aperture 1.40mm and 4.00 to 5.5 mm thick plain glass and complete all as specified and directed.

S&F stainless steel (grade-304) grills made of hollow tubes section including welding, grinding, buffing polishing and making curvatures wherever required and fitting the same with necessary holdfasts/ SS dash fastners with nut & bolts of required size, complete all as specified and directed.

S & F in repairs for 18mm thick Multi layer water proof ply wood fixed with screws to timber frame work for cabinet case both sides covered with and including cost of 0.8mm thick decorative laminates, Mica type 1 of surface finished, colour, pattern as approved fixed with adhesive and the thickness of the shutter is edge lipped by 18 mm width x 1 mm thick PVC sheet using solvent cement etc. including, magnet, piono hinges, handles as required Nos complete all as specified and directed.

S & F in repairs for 9 mm thick Multi layer water proof ply wood fixed with screws to timber frame work for cabinet case both sides covered with and including cost of 0.8mm thick decorative laminates, Mica type 1 of surface finished, colour, pattern as approved fixed with adhesive and the thickness of the shutter is edge lipped by 9 mm width x 1 mm thick PVC sheet using solvent cement complete all as specified and directed.

M&L MS Frame work as in door chowkhat with angle iron welded together ends of angle shouldered and fixed to opening and welding 4 Nos mild steel butt hinges, and 6 nos hold fasts made out of FI 25x3 mm 30 cm long for fixing of chowkhat( Butt hinges paid separately) complete all as specified and directed

Taking down cement plaster, terrazzo dado in any thickness from brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish, vegetation etc outside complex (MOD land) complete all as specified and directed.

M&L Rendering 5mm thick plastering in cement mortar 1:3 as in ceiling finished even and smooth without using extra cement to match with existing surface complete all as specified and directed.

M&L Rendering 12 mm thick in cement mortar 1:6 on fair face of brick work/ concrete surfaces (either surfaces) of wall and finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 5 mm thick in cement mortar 1:4 over a layer of 10mm thick rendering in cement mortar 1:6 on fair face of brick work/ concrete surfaces of wall with water proofing admixture finished even and smooth without using extra cement complete all as specified and directed. (WPC will be measured and paid separatly)

Supply only liquid water proofing compound complete all as specified and directed.

M&L for preparation of old decorated surface of external walls by complete removing existing treatment with mechanical sander (RPM 1500-2700) along with internal dust extraction system for clean environment certified by reputed paint manufacturers, then washing the surface with Bleaching powder solution for treatment of fungal growth and applying two coats of exterior anti fungal acrylic emulsion paint (wallmista of Berger paint or equitant in Asian paint, Nerolac etc having three years of performance warranty) over 1mm thick wall care putty and a coat of exterior water based primer all as prescribed by manufacture of paint complete all as specified and directed.

M&L for preparation of newly plastered surface of external wall all as prescribed by manufacture of paint and applying two coats of exterior anti fungal acrylic emulsion paint by using Roller (walmista of Berger paint or equitant in Asian paint, Nerolac etc having three years of performance warranty), a coat of exterior water based, over 1mm thick wall care putty primer all as prescribed by manufacture of paint complete all as specified and directed.

M&L for preparation of old decorated surface of internal wall by removing existing treatment with mechanical sander (RPM 1500-2700) along with internal dust extraction system for clean environment certified by reputed paint manufacturers and applying two coats of acrylic distemper using roller over 1mm thick wall care putty all as prescribed by manufacturer of paint Ist Quality complete all as specified and directed.

M&L for preparation of new surface of internal wall by reputed paint manufacturers and applying two coats of acrylic distemper over one coat of 1mm thick wall putty using roller all as specified and prescribed by manufacturer of paint and all as directed. Note for item No 75 to 78:- (i) The surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per manufacture’s instruction to the satisfaction of Engineer in Charge before application of surface treatment. The cost of materials, labour & T&P required for preparation of surface are deemed to be included in the rates quoted. (ii). The work must be got executed through authorised applicator of manufacture after concluding an MoU with manufacture for company back guarantee by the contractor. The authorised applicator of manufacturer shall be got approved from GE before commencement of work. (iii). All the material to be incorporated in the work shall be brought by contractor to MES store yard which will be subsequently issued by deportment for incorporation in the work to ensure the quantity to be consumed all as per recommendation of manufacture. (iv). After carrying out preparation of surface the same shall be got approved from GE before application of surface treatment (v). The colour / shade will be all as approved by GE (vi) 2.5% of cost of item will be retained as guarantee money for external painting and will be released after satisfactory completion of 3 years warranty.

M&L for preparation of newly plastered surface of ceiling and applying three coat of white wash complete all as specified and directed.

All as ser item No.79 above but two coat on old ceiling surface.

Taking up or down 15 mm bore GI tubing and connections complete all as specified and directed.

All as per item No. 81 above but 20 mm bore

S&F 15mm bore GI tubing medium grade with all fittings and fixed to wall and ceiling or laid in floors etc complete all as specified and directed.

All as per item No 83 above but 20 mm bore.

M&L for cutting chases on brick or concrete surface for concealed water tubing or girth n.exc 10cm including making good of disturbed surfaces with PCC 1:2:4 type B0 using 12.5 mm graded aggregate complete all as specified and directed.

Dismantling of RCC/ PVC water tanks exc 250 liters and n.exc 500 liters capacity of any condition or type complete all as specified and directed.

S&F white colour Rotational moulded polyethylene water storage tank 500 liters capacity, white triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including all fittings complete all as specified and as directed.

S&F in repair Gun-metal globe or gate valves 20mm bore with iron wheel head, screwed both ends for iron complete all as specified and directed.

S&F in repair 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms) complete all as specified and directed.

S&F in repair vitreous chinaware wash hand basin (WHB) size 550mm x 400mm, Ist quality, including provision of pair of mild steel angle iron brackets of suitable size duly painted and cutting for and pinning in ends of brackets in walls & making good & including providing and fixing of suitable heavy duty waste pipe and waste fitting complete all as specified and directed.

S&F in repairs PVC duel action symphonic action type flushing cistern 10 ltr capacity, low level, white with inlet, ball valve and float including brackets and flush pipe complete all as specified and directed.

S&F in repair stainless steel sink AISI 316 grade without drainage board of 1 mm thick with plug , washer and waste, including bedding in cement mortar to dwarf wall or including CP Waste , PVC Down pipe etc and fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowlsize 410mm x 330mm x 160mm or more complete all as specified and directed.

S&F in repair Chromium plated tubular towel rail, 25mm dia, ‘D’ type 60cm long between flanges of brass chromium plated and with hooks,brackets & End caps fixed with brass screws complete all as specified and directed .

S&F in repair wall mixer 3 in 1 with over head shower chromium plated for mixing hot and cold water screwed for iron pipe suitable for 15mm bore pipes complete all as specified and directed.

S&F in repair Brass chromium plated shower rose 125mm size with CP breass arm not less than 240mm long complete all as specified and directed

S&F in repair Stainless steel cromium plated Soap dish, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repairs 15mm bore Pillar tap fancy type of Chromium plated high pressure screwed for iron pipe and fixed etc. complete all as specified and directed.

S&F in repair, Sheet Glass Shelf/corner Assembly, consisting of 5.5mm thick Sheet Glass Shelf 12 Cm Wide with Chromium plated Bracket Guard and Railing 60 Cm long, complete all as specified and directed.

S&F Stainless steel 4 shelf wall mounted kitchen utensils rack, Dish rack with plate & cutlery stand of size 18x24 inches, fixed to wall plugs and chromium plated brass screws complete all as specified and directed.

S&F in repiars vitreous china squatting pan (Orissa pattern) long pan including provision of cement concrete (1:5:10) bedding fixed in repair size 580x440mm white with intergral footrest with 'P' or 'S' trap complete (excluding flushing cistern and flush) complete all as specified and directed

S&F in repair stainless steel peg set of six of size 480x38x2mm complete all as specified and directed.

S&F in repair 15 mm dia stop cock/angle cock cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle, with long shank and cup flench screwed both ends for iron or for union.fixed in repair complete all as specified and directed

S&F in repair fancy type bib taps brass cromium plated 15 mm bore size screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair Stainless steel grating 100mm dia of best quality as approved by GE including fixing in CM 1:4 to floor/nahani traps etc complete all as specified and directed.

S&F in repair PVC connection 15 mm bore and 45cm long with washers complete all as specified and directed.

M&L forcooler stand cutting hole of 230x230x230mm four Nos in walls, filling with PCC (1:2:4) Ty B-1 using 12.5mm thick stone aggregate incl fixing of 1Nos angle iron of size 50mmx50mmx6mm in C shape supported with 02x50x50x 6mm angle iron down side angular shape over all lenght approx 6.22 RM each stand including running welding with other angle, incl 2 coat of synthetic enamal paint over a coat of red oxide primer complete all as specified and directed

S&F in repair curtain rod Stainless steel fancy type 20 mm dia incl Brackets and knobs complete all as specified and directed.

M & L for cutting of bushes small trees (Peepal small plants etc) trunks shrubs of any dia and girth from roof projection, chajjas, wall junction parapet etc at any height by necessary demoliton of brick work etc if requried and making good distrubed surfaces to match with existing finihes with and incl material and labore in CM 1:4 mixed with WPC/PCC 1:3:6 type B0/Bk work in CM 1:4 as required at site and as directed by Engr-in-Charge

Supply and fixing PVC heavy duty waste pipes of 40/32mm bore suitable for wash hand basins/sinks/flushing cistern complete all as specified & directed

Dismantling of floor of WC and bath not exc 500mm deep and removing out the cinder/concrete from sunken portion, cleaning of RCC surface to remove dust, loose particle with compressed air or any other suitable method depending on site conditions, grinding any sharp edges etc complete all as specified and directed. (b) Cleaning or RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (c) M&L for a glass fiber reinforced acrylic modified cementitious coating system with base coat @ 1.50 Kg/Sqm glass fiber reinforcement and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or MC Bauchemie India Pvt Ltd. (d) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with as specified. (e) M&L for providing 25mm dia GI pipe spout projecting at least 150mm beyond outer face of wall. (f) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed. (g) The area of Each WC portion is n.exc 2.00 Sqm each. (h) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. Note : The work will be executed by authorised manufacturers/applicator.

M&L for cement concrete (1:2:4) ty B1 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed..

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified and directed.

M&L for RCC sunshades, Chajjas, Balconies, Columns, bands, beams and similar work at any position & height by dismantling loose/disintegrated portion and dubbing out with cement concrete 1:1.5:3, 40mm to 50mm thick using 6 to 12mm graded stone aggregate to make up and finished to required shape including provision of necessary supports if required and stitching of cracks with mild steel 'U' clamps made out of 8mm dia @ 150 c/c with inserting concrete block stretcher with cement mortar 1:3 mixed with adhesive chemical (Polymer based) and reinforced with Mild steel chicken wire mesh including form work where ever required and finished with 15mm thick plastering in CM 1:4 finished even and fair without using extra cement including preparation of surface to receive finishes complete all as specified and directed.

M&L for RCC chajja (irrespective size) by cleaning, replastering in cement mortar 1:3 mixed with integral water proofing compound over 40mm thick (average) PCC padding in CM 1:2:4 Type B-O (mixed with water proofing compound) to a required gradient or slope as directed by Engr-in-Charge and the plaster will extended upto 300mm on wall/roof surface to avoid leakage/seepage. Junction of old and new plaster will be well bonded with application of water proofing compound. Drip course or groove of siae 25mm x 4mm will be provided at the edge of bottom surface of the chajja. (Note:- Rates for cement plaster, WPC, PCC and formwork and specilist labours etc required for full completion of item shall be deemed to be included in the rates quoted against this item of BOQ by the contractor).

S&F in repairs stop cock 15 mm bore ISI marked fancy type (Concealed) cast copper alloy, screw down high pressure with crutch or butterfly handle screwed both ends suitable for iron pipe of 15mm bore complete all as specified and directed.

Dismantling structural steel work including doors, gates, railings etc, but excluding framed truss etc.

Dismantling timber scantlings 40 sq cm and over in section, in any position, framed work complete all as specified and directed.

Taking down asbestos (corrugated, semi-corrugated etc) sheets in roof covering complete all as specified and directed.

Taking down Wash basins, Vitreous China (flat back or angle back type) any size including all fittings complete all as specified and directed.

Taking down Vitreous China urinals (flat back or corner wall type) any size including all fittings complete all as specified and directed.

Taking down Vitreous China Water closet (Squat pattern) any size including all fittings complete all as specified and directed.

Taking down Flushing cistern and flushing pipe any size including all fittings complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and getting out in soft/ loose soil complete all as specified and directed.

M&L for PCC (1:4:8) Ty D-2 using 40mm graded stone aggregate as in cement concrete in foundations, filling and mass concrete complete all as specified and directed.

M&L for Hardcore of gauge of broken bricks n exc. 63 mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L 25 mm Cement concrete type B- 0, 1:2:4 (12.5mm graded aggregate) as in sub floor all as specified and as directed by enginner in charge complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soil complete all as specified and directed.

Removing excavated soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

Ditto, but 5mm dia and over upto and including 8mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L Reinforced cement concrete 1:2:4 Ty B-1 using 20mm graded stone aggregate (nominal mix) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L Reinforced cement concrete 1:2:4 Ty B-1 using 20mm graded stone aggregate (nominal mix) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S & F 30 mm thick flush shutters, solid core construction with block board core and plywood face panels, commercial type on both sides including fixing of rubber door cills, complete as directed.

M&L for steel ventilator with top hung shutter including hinges, steel peg stay, complete complete all as specified and directed.

S & F 4mm thick frosted sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S & F in repair of 3 mm thick plain, ordinary quality sheet glass and glazing with oil putty or fixed with wooden beads in square not exc. 0.5 sqm in each pane complete all as specified and directed.

S & F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.00mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed .

S & F in repair Galvanised mild steel wire cloth in steel window, 0.56mm nominal dia of wire and average width of aperture 1.00mm and fixed with tinned tacks, or galvanised wire staples, including one coat of synthetic enamel paint complete all as specified and directed .

S&F for 100mm long Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, fixed complete all as specified.

S&F for 200mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete complete all as specified and directed.

-Ditto- but 150mm long complete all as specified and directed.

-Ditto- but 125mm long handle complete all as specified and directed.

S & F 250 mm MS sliding door bolts, plate type, stove enameled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar (1:4) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar (1:6) on brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

S&F non skid ceramic coloured tiles 7 to 8mm thick (squre/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, in floors etc. over 15mm thick screed bed in CM 1:6 and set and jointed in neat slurry and pointed in white or coloured cement to match complete all as specified and directed

M&L for glazed ceramic coloured joint free tiles of size 350x250x7mm thick or 450x300x7 mm thick, laid over and including 10mm thick backing coat in cement mortar (1:4) in vertical surfaces of walls, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tile complete all as specified and directed.

M & L for preparation of new surface on walls and applying three coats of white wash, complete all as specified and directed.

M & L for preparation of old painted surface of wood and wood based surfaces by knotting, stopping etc of any description exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for preparation of old painted steel and iron surfaces of any description exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L 1000 ltrs Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) incl 20mm PTMT ball valve (Ball valve make:- Prayag); union , Checknut etc hoisted and fixed in position all as specified in SSR Part I.

S &F in repair chromium plated fancy type 15mm bore bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed 15mm bore.

M&L for Vitreous China urinals, half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe complete all as specified and directed.

S&F PVC valve less, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets of 10 Ltr capacity complete all as specified and directed.

S&F PVC connection 450mm long with 2 Nos brass check nuts suitable for 15mm bore of pipe with washer complete all as specified and directed.

S&F for Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) with white seat cover complete all as specified and directed.

S & F vitreous china squatting pan (Orissa pattern) long pan including connection to trap, and to flushing pipe, anti-syphonage pipe etc incl making good to floor fixed in repair size 580x440mm white with integral footrest with 'P' or 'S' trap complete (excluding flushing cistern and flush) complete all as specified and directed.

S&F vitreous china wash basin, white, Oval type, size 630x450mm, excluding taps, waste, chain and plug and porcelain stopper but including brackets including cutting and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe fixing complete all as specified and directed.

S&F for Flush pipe of polyethylene of low or high density or PVC. 32 mm dia complete all as specified and directed.

M&L for Concrete bed to drain pipes including packing under, and hunching against the sides of pipes after they are laid and tested; in for 150 mm bore pipe complete all as specified and directed.

M&L for Salt-glazed stoneware drain pipes laid in trenches and jointed as specified for 150mm bore pipecomplete all as specified and directed.

S&F 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

Ditto but multi floor trap complete all as specified and directed.

S&F in repair for 110mm PVC (SWR) WC connector with lip ring complete all as specified and directed complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) bends any radius complete all as specified and directed.

- Ditto - but 110mm bore complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and directed.

S&F in repair PVC (SWR) vent cowl 75mm bore complete all as specified and directed.

S&F in repair PVC (SWR) reducers of 110mm bore (larger bore measure) complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, rough finished complete all as specified and directed.

M&L RCC (1:2:4) Ty B-1 using 20mm graded stone aggregate as in col, pillars, piers, posts and struts complete all as specified and directed.

M&L for mild steel bolts of dia 16mm purpose made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. Exc 30cm long complete all as specified and directed.

M&L for rolled sections as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of Grade Fe 410-W complete all as specified and directed.

S&F for 6mm thick MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment of Grade Fe 410-W complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; chowkhat, railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Excavating in post holes (or similar holes)as in soft/ loose soil, each n exc 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

Dismantling and taking down carefully U/S copper / aluminium point wiring (light, fan, socket, power) complete fitting such as switches, ceiling roses, pendants, lamp holder, light fitting etc including CI/Pressed steel terminals, switch box, and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified & directed.

Dismantling and taking down carefully sub-main wiring/service wire of any size including wooden batten etc and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc complete all as specified and directed

Dismantling and taking down carefully existing DB’s any type and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc complete all as specified and directed

Material and labour for point wiring with 1.5 sqmm PVC insulated, unsheathed, stranded copper conductor (FRLS-H) cable single core 1100 Volt grade in and including rigid PVC conduit medium grade 20mm dia or more ISI Marked concealed conduit and conduit accessories and cutting chases of suitable girth where required on brick/concrete surface & making good disturbed surface,provision of GI/Pressed steel terminal switch box with plastic laminated sheet 3 mm thick fixed with brass screw and washers along with 1.5 sq mm PVC insulated unsheathed stranded copper conductor cable (FRLS-H) as earth wire connected with main common earth dolly complete all as specified and directed for the following :-

One light/fan/bell/exhaust fan point controlled by one, one-way Piano type switch 5/6 Amp complete all specified and directed.

One 3pin/5pin 5/6 Amps socket out let on same board controlled by one, one-way Piano type switch complete all specified and directed.

One 3pin/5pin 5/6 Amps socket out let on independent board controlled by one, one-way Piano type switch complete all specified and directed .

One light point controlled by two, two way piano switch 5/6 Amps complete all specified and directed.

All as per item No 197 here-in-before but wiring with 2.5 sqmm single core multi stranded copper condcutor 1100 V grade PVC insulated FRLS-H but unsheathed single core for 16 Amps power point on independent board and 2.5 sqmm FRLS cable as earthwire complete all specified and directed.

S&F switch piano flush type white finish 5/6 Amps, single pole one way, 230 volts, 50 hz complete all as specified & directed.

S &F socket out let 2 pin 5/6 Amps & 3 pin 5/6 Amps flush type, 230 volts, 50 hz all as specified and directed.

S&F switch piano flush type white finish 15/16 Amps single pole one way, 230 volts, 50 hz all as specified and directed

S &F socket out let 5 pin 15/16 Amps & 3 pin 5/6 Amps flush type, 230 volts, 50 hz all as specified and directed.

S&F switch piano flush type white finish 5 Amps, single pole two way, 230 volts, 50 hz complete all as specified & directed.

M&L bell push AC, SP 240 volts flush type 5/6 Amps, 230 volts, 50 hz complete all as specified and directed.

S&F bell ding dong elelctric 230V AC single pole all as speccified and directed.

S&F fan regulator, fulsh stepped type, electronic, 450 watt complete all as specified and directed.

Supply & fixing lamp holder (Angular/Straight ), insulated body, with back plate for batten fitting complete all as specified & directed.

S & F LED Bulb 9 Watt (cool day light) having colour temp 6500 K and lumen output 850 suitable for "B-22 type to fix on batten holder complete all as specified and directed.

M&L ceiling rose 3 terminal / PVC/ polycarbonate, isolated body all as speccified and directed

Supply and fixing sheet metal enclosure double door type for TPN (Triple Pole and neutral) 415 Volt AC 4 way with 200 Amps rated busbar all as specified and directed.

Supply and fix in replacement of MCB 63/100 Amp, 10 KA, TPN, 'C' curve, 415 V, 50 Hz including taking down existing unserviceable MCB of any description complete all as specified and directed.

Supply and fix sheet metal enclosures with metal socket and plug top Single pole and neutral enclosure with a two pin and earth plug and socket complete ISI marked, 230/240 volts, 50 hz with one single pole MCB SP 20 Amps all as specified and directed.

Supply and fixing sheet metal enclosure double door type for MCBs DB SPN(Single pole and neutral) 240V AC 8 way with 200 Amps rated busbar all as specified and directed.

Supply & fixing MCB, SP, AC, 240 volts of 06 to 32 Amps capacity 10KA, 'B' series and making connections with suitable size of copper lugs complete all as specified & directed.

Supply & fixing MCB, SPN, AC, 240 volts of 40 Amps capacity 10KA, 'B' series and making connections with suitable size of copper lugs complete all as specified & directed.

S&F LED tube light batten 20 watts 4 fts extruded polycarbonate housing, translucent diffuser with LED light source, 2000 lumen, natural white, surge protection range- 2KV, voltage protection range 120-280 VAC with intergrated driver and surge protection complete all as specified and directed.

S&F Decorative ultra slim round profile LED Tube light fitiing with extruded polycarbonate, energy efficient for mirror light 9/10 Watt 2 ft with LED light source with uniform light output, fixed on site with all accessories all as specified & directed.

Supply and fix LED 25 watt Building security light fitting mounting type made out of one piece in pressure die-cast aluminium housing with high efficient LED as lighting source and PC Cover separate compartment for driver,including bracket clamp and fixing accessories complete with electronic driver and all accessories. The fitting shall IP 66 protection, duly prewired complete all as specified and directed.

Supply and fixing sub main wiring two single core 6 sq mm PVC insulated unsheathed stranded copper conductor cable (FRLS-H) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade concealed in wall along with 6.00 Sq mm PVC insulated unsheathed copper conductor cable (FRLS-H) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion all as specified and directed.

Supply and fixing sub main wiring two single core 4 sq mm PVC insulated unsheathed stranded copper conductor cable (FRLS-H) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade concealed in wall along with 4.0 Sq mm PVC insulated unsheathed copper conductor cable (FRLS-H) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion all as specified and directed.

S&F in repair ceiling fan complete with three blades down rod, accessories 230 V, 1200mm sweep (BLDC) complete all as specified and directed .

S&F in repair Exhaust fan Steel body AC single phase 230/240 Volt of size 300 mm sweep complete with louvers including making whole and grouting of nut bolts etc and making good the disturbed sufaces of wall all as specified and directed.

S&F in repair Exhaust fan PVC body AC single phase 230/240 Volt of size 250 mm sweep complete with louvers shutter including making whole and grouting of nut bolts etc and making good the disturbed sufaces of wall all as specified and directed.

Supply and fix in repair of electric water heater, storage type steel body with copper inner tank and heating element upto 1.5/ 2 KW capacity 25 litre, BEE 5 Star rated, ISI Marked, 240 V, 50 Hz complete with all accessories such as safety valve, thermostate, NRV, Hot and cold water connection pipe all as specified and directed.

Supply and fix GI tubing medium grade ISI marked of 50 mm bore dia complete all as specified and directed.

Supply, Installed & fix maintenance free earthing copper bonded steel earth rod of 10 feet long having diameter of 17.2mm with copper bonding thickness of 250 micron,UL listed, CPRI Tested at 25 KA fault current for one second and is provided with universal clamp made of SS earth enhancing compound shall be of 50kg/pit(resistivity is less than 0.12 Ohm meter) tested as per IEC 62561-7. The above arrangements shall be provided with heavy duty earth poly plastic pit cover of 6000 kg load bearing capacity (Size:270 x 240 x 200mm) and FRLS insulated copper conductor of size 6 sqmm, single core cable drawn through and including suitable dia of medium grade GI pipe upto 7 mtr incl cutting and chases on wall and floor complete all as specified and directed. Note: The rate quoted above shall be deemed to be included for excavation and earth work, refilling, removal of surplus earth and making good the surface around chemical earthing upto depth as per manufacturer direction.

Dismantling & taking out old unserviceable LT UG cable & Supplying & laying in replacement of LT UG cable ( Conforming to IS 1554) ISI marked1.1 KV grade XLPE insulated PVC sheathed steel armoured aluminum stranded conductor in trenches / ducts / through HDPE pipe under roads of size 25 sqmm 4 core complete all as specifed and directed.

M&L river washed and screeened dry fine sand filling in trenches below and above / around under ground cable for cable protection including punniing around cable complete all as specified and directed.

M&L for well brunt bricks sub class 'B' in old size as cable protection laid flat width wise complete all as specified and directed.

Supply and fix GI tubing light grade ISI marked of 50 mm bore dia complete all as specified and directed.

Cutting existing steel tubing of size 50 mm for addition or alteration for water connection complete all as specified and directed.

Screwing existing steel tubing of size 50 mm for alterations or additions (or lengthening screw on pipe to form connector) and inserting Tee of size 50x25 mm or 50 x20 mm as per site requirement complete all as specified and directed.

S&F Exhaust fan PVC body AC single phase 230/240 Volt of size 250 mm sweep RPM not less than 900 RPM, complete with louvers including making whole on wall to fix exhaust fan and grouting with nut, bolts, washers etc and making good the disturbed sufaces of wall all as specified and directed.

Supply and fix LED 25 watt Building security light fitting mounting type made out of one piece in pressure die-cast aluminium housing with high efficient LED as lighting source and PC Cover separate compartment for driver,including bracket clamp and fixing accessories complete with electronic driver and all accessories. The fitting shall IP 66 protection, duly prewired complete all as specified and directed.

Disconnecting of solar water heater of capacity 1000 Ltr and lifting the solar water heater and placing the solar water heater on plinth/foundation making water pipe connection all as specified and directed.

M&L earthing complete with using galvanised mild steel earth plate (electrode) 600 x 600 x 6 mm thick buried directly in ground earth pit not less than 2.25 mtr depth below ground level with top edge of the plate not less than 1.5 mtr below normal ground level and earth plate surrounded with adequate quantity of charcoal dust mixed with salt to be packed thickness of 15cm all round the plates using 4mm dia GI earth lead wire as earth lead moulded and rivetted to earth plate at one end and connected to main equipment at switch / control board at another end. GI earth lead protected in and including 15mm dia GI medium grade pipe from upper end of earth plate upto equipment with & including 20mm dia bore GI pipe medium grade as water pipe from earth chamber to upper edge of the earth plate. GI funnel with wire mesh fixed on water pipe and provision of PCC 1:2:4 type B1 (using 20mm graded stone aggreagte) as per electrical plate no-03 of SSR-part-I : 2009 and testing on completion all as specified and directed. Note:- (i) If the desired earth resistance is not found within permissible limit, item shall be redone by contractor at no extra cost. (ii) Cost of GI wire 4 Sqmm and 15mm dia pipe medium grade upto 7.5m is deemed to be included in the rate quoted for this item.

Supplying & laying in replacement of LT UG cable (Conforming to IS 1554) ISI marked1.1 KV grade XLPE insulated PVC sheathed steel armoured aluminum stranded conductor in trenches / ducts / through HDPE pipe under roads of size 10 sqmm 4 core complete all as specifed and directed.

Material and labour for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure type, laid in trenches/floors/duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etc for protection of LT cable XLPE grade 1100 volts complete all as specified and directed.

Supply and laying SDR -11 CPVC pipe of outer dia 20 mm schedule 80 pipe including CPVC fitting like elbow union, male brass threaded adapted,, female brass threaded adapter, cocket etc complete all as specified and directed.

Supply and fixing CPVC brass ball valve of dia 20 mm complete all as specified and directe.

BHAGAT JI ENTERPRISES (BID ID -3149780)

Alankar Traders (BID ID -3155033)

RAJENDER CONSTRUCTION CO (BID ID -3147095)

IRFANAHMAD CONTRACTOR (BID ID -3146663)

M/S GIRI CONSTRUCTION CO. (BID ID -3149782)