REPAIR AND MAINTENANCE OF STEEL FURNITURES AND SOFA SETS INCLUDING PAINTING POLISHING AT BINNAGURI UNDER GE NORTH BINNAGURI

Amount

STEEL FURNITURE Taking down existing unserviceable Top of Table office clerk Steel and supply and fixed with new 6mm thick veneered decorative ply wood, grade 1st quality with BWR resin with decorative face veneer on one face in same position with new screws including providing aluminium beading all round as per existing shape and size complete all as specified and as shown on drawing. (DRAWING No. 84(M)/FD-1004)

Taking down existing unserviceable lock lever of Table office clerk Steel and supply and fixed with new steel lock 6 (six) lever for drawer with duplicate key in same position with new screws complete all as specified and as shown on drawing. (DRAWING No. 84(M)/FD-1004)

Material and labour for spot welding in repairs of broken steel frame and drawer of table office clerk steel complete all as directed. (DRAWING No. 84(M)/FD-1004) (Note :- Each spot shall not exc. 5 cm in length and not exc. 2mm in thickness.)

Taking down existing unserviceable Top of Table office Officer Steel and supply and fixed with new 6mm thick veneered decorative ply wood, grade 1st quality with BWR resin with decorative face veneer on one face in same position with new screws including providing aluminium beading all round as per existing shape and size complete all as specified and as shown on drawing. (DRAWING No. 84(M)/FD-1003)

Taking down existing unserviceable steel lock lever of Table office Officer Steel and supply and fixed with new steel lock 6 (six) lever for drawer with duplicate key in same position with new screws complete all as specified and as shown on drawing. (DRAWING No. 84(M)/FD-1003)

Material and labour for spot welding in repairs of broken steel frame and drawer of table Office Officer steel complete all as directed. (DRAWING No. 84(M)/FD-1003) (Note :- Each spot shall not exc. 5cm in length and not exc. 2mm in thickness.)

Taking down existing unserviceable table top 900 mm x 600 mm with and without drawer Steel and supply and fixed new Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick teak wood beading around the edging all complete specified shown on drawing & directed. (Drawing No. FD 1007/1008)

Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of Table complete all as specified and as shown in drawing. (Note : Material to be weled not to exceeding 2.00mm in thickness) (Drawing No. FD 1007)

Taking down existing unserviceable lock lever of Table office clerk Steel and supply and fixed with new steel lock 6 (six) lever for drawer with duplicate key in same position with new screws complete all as specified and as shown on drawing. (DRAWING No. FD-1007)

Taking down existing unserviceable table top 900 mm x 900 mm with and without drawer Steel and supply and fixed new Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick teak wood beading around the edging all complete specified shown on drawing & directed (Drawing No. FD 1009)

Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of Table complete all as specified and as shown in drawing. (Drawing No. FD 1009) (Note : Material to be weled not to exceeding 2.00mm in thickness)

Removing of unserviceable/s legs of size 760 mm long 25 mm x 25 mm square tube mild steel 1.6 mm wall thickness and supply and fixed new legs of same size at the same position by welding as per drg and welding to the broken frame when ever required complete all as directed. (Drawing No. FD 1009)

Removing of unserviceable/s side/ front/ rear rail, 25 mm x 25 mm square tube mild steel 1.6 mm wall thickness and supply and fixed new legs of same size at the same position by welding as per drg and welding to the broken frame when ever required complete all as directed. (Drawing No. FD 1009)

Taking down decayed top from Table dining ORs and supply and fixing new top 18 mm thick pre-laminated particle board, Grade II Type I exterior grade conforming to IS-12823-2006 with 4mm thick teak wood beading all around the edging complete all as specified and as directed. (Drawing No. FD-165(M)

Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of chair verandah complete all as specified and as shown in drawing. (Drawing No. FD- 165(M) Note : Material to be weled not to exceeding 2.00mm in thickness)

Taking down existing unserviceable Teapoy Verandah top and supply and fixed new Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick teak wood beading around the edging all complete specified shown on drawing. (Drawing No. FD 35(M)/255)

Material and labour in repair to broken frame leg of teapoy verandah by spot welding not exc 2.50cm in length complete all as specified and as directed. (Drawing No. FD 35(M)/255) (Note : Materials to be welded not exc. 2.50 cm in thickness).

Taking out unserviceable seat frame of Chair CB with Arm and Supply and fixed Seat frame made from Teak wood well seasoned and termite treated, with making holes of weaving slightly rounded on the edges and applying two coat of black paint over wood filler on all exposed new wooden surfaces of seat frame shall be painted with high glossy paint after preparation of new wooden surface and weaving with new cane seat and back in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane bordering and 0.4mm thick gola type weighing not less than 6 gms per 10 running meters complete all as specified & as directed and as shown on drawing.complete all as specified and shown in drawing. (Drawing No. FD-75(M).

Taking out unserviceable back frame of Chair CB with Arm and Supply and fixed Back frame made from Teak wood well seasoned and termite treated, with making holes of weaving slightly rounded on the edges and applying two coat of black paint over wood filler on all exposed new wooden surfaces of back frame shall be painted with high glossy paint after preparation of new wooden surface and weaving with new cane seat and back in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane bordering and 0.4mm thick gola type weighing not less than 6 gms per 10 running meters complete all as specified & as directed and as shown on drawing.complete all as specified and shown in drawing. (Drawing No. FD-75(M).

Taking out old damaged/broken arm rest and supply and fixed new arm rest in the same position as per existing shape and size made out of well seasoned first class hard wood ‘Teak ’ timber including applying two coat of black paint over wood filler on all exposed new wooden surfaces after preparation of new wooden surfaces complete all as specified and as shown on drawing. (Drawing No. FD-75(M).

Taking out old rusted/damaged/broken flat iron support of chair CB steel with arms and supply and fixed new mild steel flat iron of size 20 x 5mm, 75mm long to bottom of steel frame in support of wooden seat frame duly welded with making hole for fixing screw complete all as specified and as shown on drawing. (Drawing No. FD-75(M).

Material and labour for spot welding to damaged/broken seat frame of chair CB with Arm or without Arm complete all as specified and shown on drawing. (Drawing No. FD-75(M). (Note : length of each spot welding will not exceed 4 cm in length and 2 mm in thichness).

Taking out unserviceable seat frame of Chair CB without Arm and Supply and fixed Seat and Back frame made from Teak wood well seasoned and termite treated, with making holes of weaving slightly rounded on the edges and applying two coat of black paint over wood filler on all exposed new wooden surfaces of seat shall be painted with high glossy paint after preparation of new wooden surface and weaving with new cane seat in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane bordering and 0.4mm thick gola type weighing not less than 6 gms per 10 running meters complete all as specified & as directed and as shown on drawing.complete all as specified and shown in drawing. (Drawing No. FD-75(M).

Taking out unserviceable back frame of Chair CB without Arm and Supply and fixed Seat and Back frame made from Teak wood well seasoned and termite treated, with making holes of weaving slightly rounded on the edges and applying two coat of black paint over wood filler on all exposed new wooden surfaces of seat shall be painted with high glossy paint after preparation of new wooden surface and weaving with new cane seat in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane bordering and 0.4mm thick gola type weighing not less than 6 gms per 10 running meters complete all as specified & as directed and as shown on drawing.complete all as specified and shown in drawing. (Drawing No. FD-75(M).

Taking out old rusted/damaged/broken flat iron support of chair CB steel without arms and supply and fixed new mild steel flat iron of size 20 x 5mm, 75mm long to bottom of steel frame in support of wooden seat frame duly welded with making hole for fixing screw complete all as specified and as shown on drawing. (Drawing No. FD-75(M).

Taking out unserviceable seat frame of Chair CBA Special with Hand rest and Supply and fixed Seat frame made from 2nd class hard wood well seasoned and termite treated duly canned in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane complete all as specified and shown in drawing. (Drawing No. FD-120)

Taking out unserviceable Back frame of Chair CBA Special with Hand rest and Supply and fixed back frame made from 2nd class hard wood well seasoned and termite treated duly canned in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane complete all as specified and shown in drawing. (Drawing No. FD-120)

Taking out unserviceable plastic cane from seat frame of Chair CBA Special with Hand rest and Supply and fixed for weaving the seat of Chair in Godrej pattern with new 2 mm wide half round and 4mm for border approved quality complete all as specified and shown in drawing. (Drawing No. FD-120)

Taking out unserviceable plastic cane from back frame of Chair CBA Special with Hand rest and Supply and fixed for weaving the back of Chair in Godrej pattern with new 2 mm wide half round and 4mm for border approved quality complete all as specified and shown in drawing. (Drawing No. FD-120)

Taking out all unserviceable hand rest from its position and supply and fixed new hand rest made out of 20 mm thick well seasoned teak wood plank in one piece on hand rest with piano hinges at right side complete all as specified and shown on drawing. .(Drawing No. FD-120)

Taking out all old unserviceable arm rest and supply and fixed new arm rest made out of well seasoned teak wood timber 25 mm thick duly polished as per existing shape & size complete all as per specified and as shown on drawing. (Drawing No. FD-120)

Material and labour for spot welding to damaged/broken seat frame of chair CBA spl with hand rest complete all as specified and shown on drawing. (Note : length of each spot welding will not exceed 8 cm in length and 2 mm in thichness).(Drawing No. FD-120)

Taking out unserviceable plastic cane of chair Verandah seat and back and supply and fixing for weaving the seat and back of Chair Varandah in Godrej pattern with new 4 mm wide half round approved quality cane on steel surface of chair complete all as specified and as directed. (Drawing No. FD-19(M)/256/359)

Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of chair verandah complete all as specified and as shown in drawing. (Drawing No. FD- 19(M)/256/359) (Note : Material to be weled not to exceeding 2.00mm in thickness)

Taking down existing unserviceable leg (Right/Left) of Locker bed side steel and supply and fixed with new Leg of size 450 mm x 80 mm x 100 mm made out of 1mm Mild steel sheet in same position and applying two coatss of Synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer complete all as specified and shown on drawing. (Drawing No. FD-257/1029)

Material and labour in repair to broken/damaged bottom leg of locker bed side steel by spot welding complete as specified and as directed. (Drawing No. FD-257/1029) (Note: Thickness of metal to be welded shall not exceed 2mm.)

Taking out loose shelf from of locker Bed Side Steel and refixing the same position rigidly after minor repairs by providing new clips, nut and bolts as required complete all as directed. (Drawing No. FD-257/1029)

Taking out existing unserviceable hasp and stapple and Supply and fixed new hasp and staple of size 100 mm x 20 mm x 3 mm Chromium plated Hasp and staple to front shutter of approved make and design complete all as specified and as shown on drawing (Make :- Mowjee or Classic) (Drawing No. FD-257/1029)

Material and labour in repairing of existing unserviceable hinges by spot welding and make it functional by providing pin/greasing etc. complete all as directed. (Note :- Each spot welding shall not be more than 2.5cm in length and materials to be welded not exceeding 3mm in thickness.) (Drawing No. FD-257/1029)

Taking out of unserviceable old handles from the front of shutter and Supply and fixed new 115mm long chrome plated handle of approved make and design complete all specified and as shown on drawing. (Drawing No. FD-257/1029)

Taking out of old unserviceable broken curtain rod including brackets and Supply and fixed new curtain rod of aluminium 19/20mm dia, 1.5 mm wall thickness with steel brackets both sides in the same position by spot welding including painting with applying two coat of Olive Green synthetic enamel paint (1st quality over a coat of red oxide zinc chrome primer by spray machine over steel brackets after preparation of new steel surfaces complete all as specified and as shown on drawing. (Drawing No. FD-257/1029)

Taking out old unserviceable/damaged bottom shelf and Supply and fixed new bottom shelf as per existing shape and size made out of 1mm thickness plain mild steel sheet and fixed in the same position with shelf clips, nuts & bolts etc including applying painting with two coat of Olive Green synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer by spray machine before fixing and after preparation of new steel surfaces complete all as specified and shown on drawing. (Drawing No. FD-257/1029)

Taking out old unserviceable/damaged intermediate shelf and Supply and fixed new intermediate shelf as per existing shape and size made out of 1mm thickness plain mild steel sheet and fixed in the same position with shelf clips, nuts & bolts etc including applying painting with two coat of Olive Green synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer by spray machine before fixing and after preparation of new steel surfaces complete all as specified and shown on drawing. (Drawing No. FD-257/1029)

Taking out old unserviceable/damaged inner partition and Supply and fixed new inner partition as per existing shape and size made out of 1mm thickness plain mild steel sheet and fixed in the same position with shelf clips, nuts & bolts etc including applying painting with two coat of Olive Green synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer by spray machine before fixing and after preparation of new steel surfaces complete all as specified and shown on drawing. (Drawing No. FD-257/1029)

Taking out old unserviceable/damaged shutter (Left/Rigt) and Supply and fixed new shutter as per existing shape and size made out of 1mm thickness plain mild steel sheet and fixed in the same position with shelf clips, nuts & bolts etc including applying painting with two coat of Olive Green synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer by spray machine before fixing and after preparation of new steel surfaces complete all as specified and shown on drawing. (Drawing No. FD-257/1029)

Repair of Almirah steel large with shelves as appended below : Taking down existing unserviceable botton leg (left/right) from its position and supply and fixed new bottom leg of size 450 mm x 80 mm x 100 mm made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)

Taking down existing unserviceable door shutter by cutting area not exc.100 Sqcm squre/rectangle from its position and supply and fixed new door shutter made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)

Taking down existing unserviceable bottom shelve from its position and supply and fixed new shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)

Taking down existing unserviceable intermediate shelve from its position and supply and fixed new intermadiate shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)

Taking down existing unserviceable door shutter from its position and supply and fixed new door shutter (Left/ Right) out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)

Taking out unserviceable damaged lock from its position of almirah (large steel) and Supply and fixed new 6 lever steel lock as per existing shape and size as approved with keys in duplicate complete all as specified. Make :Link/Godrej/Standard/Aligarh ( Drawing No. FD-67(M)/FD-1031)

Taking out old and removing old unserviceable handle from Almirah steel large and Supply and fixed steel chromium plated handle 125mm long of existing shape and size complete all as specified and as directed and shown on drg.(Make :- Mowjee or Classic) ( Drawing No. FD-67(M)/FD-1031)

Taking out loose shelf from its position of Almirah large steel and re-fixing the same rigidly after minor repairs by providing new clips, nuts & bolts of existing size as required complete all as directed. ( Drawing No. FD-67(M)/FD-1031)

Material and labour for running welding in repairs to broken/damaged sides (left/right), back and top of almirah steel large complete all as directed. (Note : Thickness of materials to be welded not exceeding 2mm in thickness and length of each welding exceeding 9mm but not exceeding 20mm in length) ( Drawing No. FD-67(M)/FD-1031)

Material and labour for repair of existing loose hinges by spot welding and make it functional by providing new steel pin including greasing etc required for smooth function complete all as directed. ( Drawing No. FD-67(M)/FD-1031)

Material and labour for taking out loose leg (right/left) from its position and re-fixing the same in existing position with necessary run welding of Almirah large complete all as directed. (Note : Thickness of metal to be welded shall not exceed 2mm) ( Drawing No. FD-67(M)/FD-1031)

Repair of Almirah steel Medium with shelves as appended below : Taking down existing unserviceable botton leg (left/right) from its position and supply and fixed new bottom leg of size 450 mm x 80 mm x 100 mm made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1032)

Taking down existing unserviceable bottom shelve from its position and supply and fixed new shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1032)

Taking down existing unserviceable intermediate shelve from its position and supply and fixed new intermadiate shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1032)

Taking down existing unserviceable door shutter from its position and supply and fixed new door shutter made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1032)

Taking out and removing of old broken/damaged steel of door shutter with necessary cutting in square/rectangle in shape and Supply and fixed new MS sheet as per existing size and shape not exceeding 100 Sq cm each made out of 1 mm thickness plain mild steel sheet fixed by run welding of required length including applying two coat of synthetic enamel paint (1st grade quality) over a coat of red oxide zinc chrome primer by spray machine all complete as specified and as directed. ( Drawing No. FD-67(M)/FD-1032)

Taking out unserviceable damaged lock from its position of almirah (medium steel) and Supply and fixed new 6 lever steel lock as per existing shape and size as approved with keys in duplicate complete all as specified. Make :Link/Godrej/Standard/Aligarh ( Drawing No. FD-67(M)/FD-1032)

Taking out old and removing old unserviceable handle from Almirah steel medium and Supply and fixed steel chromium plated handle 125mm long of existing shape and size complete all as specified and as directed and shown on drg.(Make :- Mowjee or Classic) ( Drawing No. FD-67(M)/FD-1032)

Material and labour for running welding in repairs to broken/damaged sides (left/right), back and top of almirah steel medium complete all as directed. (Note : Thickness of materials to be welded not exceeding 2mm in thickness and length of each welding exceeding 9mm but not exceeding 20mm in length) ( Drawing No. FD-67(M)/FD-1032).

Material and labour for repair of existing loose hinges by spot welding and make it functional by providing new steel pin including greasing etc required for smooth function complete all as directed. ( Drawing No. FD-67(M)/FD-1032)

Taking out loose shelf from its position of Almirah medium steel and re-fixing the same rigidly after minor repairs by providing new clips, nuts & bolts of existing size as required complete all as directed. ( Drawing No. FD-67(M)/FD-1032)

Material and labour for taking out loose leg (right/left) from its position and re-fixing the same in existing position with necessary run welding of Almirah large complete all as directed. (Note : Thickness of metal to be welded shall not exceed 2mm) ( Drawing No. FD-67(M)/FD-1032)

Taking out broken existing glass pane from shutter and Supply and Fixing new 3mm thick plain ordinary glass pane with putty best quality keeping the shutter freely swinging up and rolled complete all as specified and as directed. (Drawing No. FD- 1028)

Taking out and removing old unserviceable handle from bookcase steel and Supply and fixed steel chromium plated handle 125mm long of existing shape and size complete all as specified and as directed and shown on drg.(Make :- Mowjee or Classic) ( Drawing No. FD-1028)

Taking out unserviceable damaged lock from its position of bookcase steel and Supply and fixed new 3 lever steel lock as per existing shape and size as approved with keys in duplicate complete all as specified. Make :Link/Godrej/Standard/Aligarh ( Drawing No. FD-1028)

Taking down existing unserviceable bottom shelve from its position and supply and fixed new bottom shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-1028)

Taking down existing unserviceable intermediate shelve from its position and supply and fixed new intermadiate shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-1028)

Material and labour for spot welding in repairs not exc 5cm in length of broken steel angle and corner bracket of rack steel complete all as specified and as shown in drawing. (Drawing No. FD- 106(M)/ 1038) (Note : Material to be weled not to exceeding 2.00mm in thickness)

Material and labour for spot welding in repairs not exc 5cm in length of broken shelve of rack steel complete all as specified and as shown in drawing. (Drawing No. FD- 106(M)/ 1038) (Note : Material to be weled not to exceeding 2.00mm in thickness)

Taking out old unserviceable wooden seat plank from Form with back and Supply and fixed new seat plank made out of 25mm thick well seasoned first class hard wood 'Teak Wood 'timber as per existing shape and sizes with 09 Nos GI nuts, bolts and washers including preparation of wooden surfaces and applying French polish to achive high glossy finish over wood filler to exposed surfaces of timber complete all as specified and as shown on drawing. (Drawing No. FD-78(M)/ 77 (M)

Taking out old unserviceable wooden back plank from Form with back and Supply and fixed new seat plank made out of 19mm thick well seasoned first class hard wood 'Teak Wood 'timber as per existing shape and sizes with 04 Nos GI nuts, bolts and washers including preparation of wooden surfaces and applying French polish to achive high glossy finish over wood filler to exposed surfaces of timber complete all as specified and as shown on drawing. (Drawing No. FD-78(M)/ 77 (M)

Taking out old unserviceable seat plank from 'form without back' and refixing the same with providing 09 Nos GI nuts bolts and washer complete all as specified and as directed and shown on drawing. (Drawing No. FD-78(M)/ 77 (M)

Material and labour for spot welding in repairs not exc 2.5 cm in length of broken / damaged leg//stiffener of Form with or without back steel complete all as specified and as shown in drawing. (Drawing No. FD- 78(M)/ 77 (M) (Note : Material to be weled not to exceeding 2.00mm in thickness)

SOFA SETS Taking out of unserviceable back long rail from sofa 5 seater (3+1+1) and Material and labour with new 1st class hard wood (Teak Wood) of size 35 mm x 70 mm x 1680mm , well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 281)

Taking out of unserviceable stiffener in seat and back from sofa 5 seater (3+1+1) and Material and labour with new 1st class hard wood (Teak Wood) of size 20 mm x 50 mm x 600mm , well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 281)

Taking out of unserviceable Arm rest (Handle) from sofa 5 seater (3+1+1) and Material and labour with new 1st class hard wood (Teak Wood) arm rest (Handle) as per existing, well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 281)

Taking out of unserviceable cover of tapestry cloth with lining from Foam cushion of size 560mm x 530mmx100mm and supply and stiching with new lining and best quality tapestry cloth of approved quality and colour (not less than Rs. 280/- per RM) duly wraped and cover shall be of removable type by providing best quality plastic Zip over Tapestry cloth complete all as specified and as directed. (Drawing No. FD- 281)

Taking out of unserviceable Foam cushion and supply and fixed new foam cushion 100 mm thick 'U' foam, 40 density, of size 500 mm x 530 mm all as directed. (Foum shall be sleepwell/courlon/ Sleepwell/ Dunlop). (Drawing No. FD- 281)

Taking out of unserviceable back long rail from sofa 4 seater (2+1+1) and Material and labour with new 1st class hard wood (Teak Wood) of size 35 mm x 70 mm x 1120mm , well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 281)

Taking out of unserviceable stiffener in seat and back from sofa 4 seater (2+1+1) and Material and labour with new 1st class hard wood (Teak Wood) of size 20 mm x 50 mm x 600mm , well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 281)

Taking out of unserviceable Arm rest (Handle) from sofa 4 seater (2+1+1) and Material and labour with new 1st class hard wood (Teak Wood) arm rest (Handle) as per existing, well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 281)

Taking out of unserviceable cover of tapestry cloth with lining from Foam cushion of size 560mm x 530mmx100mm and supply and stiching with new lining and best quality tapestry cloth of approved quality and colour (not less than Rs. 280/- per RM) duly wraped and cover shall be of removable type by providing best quality plastic Zip over Tapestry cloth complete all as specified and as directed. (Drawing No. FD- 281)

Taking out of unserviceable Foam cushion and supply and fixed new foam cushion 100 mm thick 'U' foam, 40 density, of size 500 mm x 530 mm all as directed. (Foum shall be sleepwell/courlon/ Sleepwell) (Drawing No. FD- 281)

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of steel surface (inside & outside surface) including doors shelves and legs, applying synthetic enamel paint (1st quality) over a coat of red oxide primer Zinc chrome primer by spray paint machine complete all as specified specified and shown on drawing for following:-

Tabble Office Clerk Steel (Drawing No. FD-84(M)/ 1004 )

Tabble Office Officer Steel (Drawing No. FD-84(M)/ 1003 )

Tabble Steel 900 x 600 x 760 mm (Drawing No. FD- 1007 )

Tabble Steel 900 x 900 x 760 mm (Drawing No. FD- 1009 )

Tabble Dinning Ors (Drawing No. FD- 165(M) )

Teapoy verandah (Drawing No. FD- 35(M) /255 )

Chair CB Steel with arms (Drawing No. FD- 75(M) )

Chair CB Steel without arms (Drawing No. FD- 75(M) )

Chair CBA special with Hand rest steel (Drawing No. FD- 120(M)

Chair Verandah (Drawing No. FD- 19(M) /256/ 359 )

Locker bed side steel. (Drawing No. FD- 257/ 1029)

Almirah Large Steel (Drawing No. FD-67(M)/ 1031)

Almirah Medium Steel (Drawing No. FD-67(M)/ 1032 )

Bookcase Steel (Drawing No. FD-90(M)/ 1028 )

Rack Steel Adjustable steel (Drawing No. FD- 106(M) / 1038 )

Form with back/ Form without back Steel (Drawing No. FD- 78(M) / FD-77(M)

Material and labour for preparing & polishing wooden and wood based materials of any description and of any lenghth and width and applying french polish to furniture articles as specified with one or more coat till glossy finish achieved including filler as required all as specified in particular specifications and as shown on drawing and as directed by Engineer-in-Charge for the following wooden furniture:-

Sofa set 4 (2+1+1) Seater Wooden (Drawing No. FD- 281 )

Sofa set 5 (Five) (3+1+1 ) Seater Wooden (Drawing No. FD- 281)

Replacement of rubber shoes with new one for Table Office clerk steel /Table office officer steel/ Tables complete all as specified and as directed.

Replacement of PVC Cap with new one for CB Chairs steel etc complete all as specified and as directed.

M/s. RAMPHAL GARG

M/S East India Traders

M/S MOHAN KUMAR BANSAL

PRAVESH KUMAR

shekhar & company