CA No CWE/FZR- /2020-21 Special repair to Bldg No P-349 of Lt AD Regt (Comp) at Dholewal MIL Complex under GE Ludhiana

Amount

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level), complete all as specified.

Demolition of reinforced cement concrete as in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work and removing debries outside MoD land, complete all as specified

M&L for reinforced cement concrete (1:2:4) type B-1 nominal mix (20 mm graded stone aggregate) as in beams, cantilevers, and lintels etc and similar articles, complete all as specified.

M&L for reinforced cement concrete (1:2:4) type B-1 nominal mix (20 mm graded stone aggregate) as in chajjas etc and similar articles, complete all as specified.

Use and waste rough finished Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as directed by Engr-in-Charge

Use and waste rough finished Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5cm but not exc.10cm wide, complete all as specified.

S&F Mild steel TMT bars 10 mm dia and over as in reinforcement cut to length bent to shape required including cranking, hooking at ends and binding with mild steel wire (annealed) not less than 0.9mm dia FE-500/550 confirming to IS-1786-1985 all as specified.

Taking down cement plaster from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc, complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified.

M&L for Taking down wooden/steel chowkhats or frames with shutters (without taking off shutters from the frames) of size exceeding 1.5 Square metre and not exceeding 4 Square metre each.including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts,making good jambs with plaster in CM(1:4) to match with existing finish, complete all as specified.

Taking down door shutter of any description, exc 1 Sqm but not exceeding 2 sqm each and refixing in the same opening, complete all as specified.

Taking down door shutter of any description, exc 1 Sqm but not exceeding 2 sqm each, complete all as specified.

M&L for Taking down wooden/steel chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Square metre each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts,making good jambs with plaster in CM(1:4) to match with existing finish, complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified.

M&L Hardcore of broken bricks of gauge not exc 63mm, deposited spread and leveled in layers not exc 15 cm thick watered and rammed to a true surface, complete all as specified.

M&L for 25mm thick Cement concrete (1:2:4) type B-0 using 12.5 mm graded stone aggregate as in flooring, complete all as specified.

Dismantling of stone slabs and tiles of any description or thickness in floor, aprons,etc laid bedded and pointed in any surfaces complete all as specified and directed.

M&L for granite (of any type) work 20mm thick (polished) in steps, jambs, pillars, window cills, cooking platforms and including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite & including 20 mm thick screed bed in cement mortar (1:6) laid over, complete all as specified.

M&L for Kota stone slabs, 20mm to 25mm thick, machine cut as in flooring of size not less than 0.25 Square metre each, set and jointed in cement slurry and pointed in cement mixed with pigment to match the shade of slab laid over & including screed bed of 15 mm thick in cement mortar (1:6) including rubbing, cutting and polishing (mirror type) complete all as specified.

All as per item No 19 herein before but in one piece as in tread of stairs laid over & including screed bed 20 mm thick in cement mortar (1:6) complete all as specified.

All as per item No 19 herein before but in skirting/dado laid over cement mortar (1:4) 10mm thick backing coat, complete all as specified.

All as per item No 19 herein before but in one piece as in risers laid over cement mortar (1:4) 10mm thick backing coat, complete all as specified.

M&L for Non skid Ceramic coloured ( colour and shade as approved) tiles,any shape, 7mm to 8 mm thick area of each tile exc. 0.11 sqm and not exc 0.18 sqm as in flooring set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles laid over & including 15 mm thick screed in cement mortar (1:6) laid over, complete all as specified.

All as per Item No-23, but as on vertical surfaces such as skirting/dado over and including 10 mm thick rendering in cement mortar (1:4), complete all as specified.

M&L for Glazed ceramic tiles, coloured (colour & shade as approved), of size 450x300x7 mm thick on vertical surfaces such as in skirting/dado etc set and jointed in cement slurry and pointed in white cement with pigment to match the colour of tiles, laid over & including 10 mm thick backing coat in cement mortar (1:4), complete all as specified.

S&F 4mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm complete all as specified.

S&F 4mm thick, figured glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm complete all as specified.

M&L for Rendering 12mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified.

M&L for wire netting of galvanised steel wire, 0.9mm dia and 20mm mesh fixed with tinned tacks of GI wire to steel members, complete all as specified.

M&L Rendering 5 mm thick in cement mortar (1:3) on ceiling finished even and smooth without using extra cement, complete all as specified.

M&L for Rendering 15 mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified.

M&L Preparation of newly plastered surfaces and applying two coats of oil bound distemper, over a coat of chalk whiting, and a coat of primer, complete all as specified and as directed.

M&L Preparation of newly plastered surfaces of ceiling & applying three coats of white wash, complete all as specified.

M&L Preparation of new plastered surfaces walls etc and applying two coats of cement base paint over a coat of primer, complete all as specified.

M&L for 40mm thick cement concrete (1:2:4) type B-1 (20 mm graded stone aggregate) as in flooring, finished even and smooth without using extra cement, complete all as specified.

M&L for Cement concrete (1:3:6) type C-2 using 20 mm graded stone aggregate as in 50mm thick plinth protection, surfaces finished even and fair without using extra cement, including provision of construction joints, complete all as specified and directed

Supply only 38 mm x 3 mm glass dividing strips as in floors, complete all as specified.

S&F Factory made solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube, complete all as specified in MES Schedule Part-I (2009),including making good jambs in CM (1:4) with finishes to match with existing, complete all as per specification & drawing.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site, complete all as per specification in MES Schedule Part-I (2009) & drawing.

S&F Factory made pressed steel frames made of 1.25 mm thick MS sheet of profile 105 mm X 60 mm for door and window frames with one or more rebates including lock strike plate, shock absorber, 20 mm dia 60 mm long MS conduit for housing of a drop bolt,hinges, hold fasts/lugs etc, treating of internal surfaces of chowkhats with coal tar or black paint including hold fasts/lugs etc complete all as specified.

S&F Factory made pressed steel frames made of 1.25 mm thick MS sheet of profile 125 mm X 60 mm for door and window frames with one or more rebates including lock strike plate, shock absorber, 20 mm dia 60 mm long MS conduit for housing of a drop bolt,hinges, hold fasts/lugs etc, treating of internal surfaces of chowkhats with coal tar or black paint including hold fasts/lugs etc complete all as specified.

M&L Cement concrete (1:3:6) type C-1 (20 mm graded stone aggregate) as in pressed steel chowkhats and bed blocks of hold fast including necessary formwork, complete all as specified.

S&F Factory made, 35mm thick, 2nd class hard wood (Hollock), plain framed, panelled shutters, any number of panels, panels shall be of 9 mm thick B.W.P. commercial ply or 12mm thick BWR grade veneered particle board medium density, wood particle board with commercial face veneers, size of members as specified in clause 8.24(a) of MES Schedule Part-I section-8 complete all as specified.

S&F Factory made 35 mm thick,2nd class hard wood (Hollock), glazed and skeleton shutters open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass/gauge etc for doors, size of members as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, complete all as specified.

M&L Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified.

M&L Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, complete all as specified.

M&L Preparation of old treated wooden surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

M&L Preparation of old treated steel surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

S&F Extruded Aluminium alloy tower bolts,150 mm long and fixed with steel screws complete all as specified.

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified.

S&F 100 mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified.

S&F 125mm aluminium (cast type) anodized, long handle fixed with steel screws complete all as specified.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples, complete all as specified .

S&F in repair, PVC bathroom cabinet mirror size 350x450mm of suitable design with shutter, complete all as specified.

S&F in repair, 300mm mild steel helical door spring including roller and roller plate complete all as specified.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends swan-necks etc, including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fitting and accessories).

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls including distance pieces and incld stack clamps with nuts & bolts, complete all as specified.

S&F 110 mm bore PVC (SWR) bends/shoe and provided with access door any radius fixed to walls including distance pieces and stack clamps, including making good around complete all as specified.

M&L for 18/19mm thick Block boards, grade 2, interior grade, commercial type, fixed with screws to timber frame-work as fixed in repairs, complete all as specified.

S&F in repair 20mm bore brass ball valve high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule, complete all as specified.

Taking up or down existing steel water tubing, 15 mm bore alongwith connections fixed/laid in any situation, complete all as specified

Taking up or down existing steel water tubing, 20 mm bore alongwith connections fixed/laid in any situation, complete all as specified.

S&F Galvanised iron steel water tubing, 15 mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors including cutting and making good, complete all as specified.

S&F Galvanised iron steel water tubing, 20 mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors including cutting and making good, complete all as specified.

Re-Fixing only, steel water tubing, 15mm bore and connections in new or old position using new fittings fixing to wall/ceiling or laid in floors complete all as specified.

Re-Fixing only, steel water tubing, 20mm bore and connections in new or old position using new fittings complete all as specified.

S&F in repairs PVC syphonic action type low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, 32 mm PVC flush pipe and necessary fixing arrangements and connecting to water pipe, complete all as specified .

S&F in repair 15 mm bore pillar tap fancy type, chromium plated, screwed down, high pressure with crutch or butter fly handle, complete all as specified.

S&F in repairs wash hand basin, flat back 550mm x400mm vitreous china (white) including PTMT waste coupling/fittings, 32 mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing , complete all as specified.

S&F Vitreous china white semi pedestal pattern (Anglo Indian Type) white with trap including PVC seat cover, PVC Jet spray and connection to drain or out going pipe and 100 mm bore cast iron ‘P’ trap and flushing pipe anti-syphonage pipe etc, fixed as in repair, complete all as specified.

S&F in repair Cast iron floor trap for 75 mm bore pipe with cast iron grating including jointing to waste pipe in run lead fixed in cement concrete type B-1 (1:2:4), complete all as specified.

S&F in repairs 75 mm dia cast iron soil, waste and vent pipe, sand cast, in any length with or without ears with cement joints fixed to walls with and including suitable clamps, complete all as specified.

S&F in repairs 100 mm dia cast iron soil, waste and vent pipe, sand cast, in any length with or without ears with cement joints fixed to walls with and including suitable clamps, complete all as specified.

S&F in repair 15 mm bore bib tap of fancy type, chromium plated, screwed down, high pressure with crutch or butter fly handle, complete all as specified.

S&F in repair brass15mm dia chromium plated sink mixer, complete all as specified and directed.

S&F in repair 15mm stop cock/angle cock cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or brass ferrule fancy type chromium plated with fancy type shank and cup, complete all as specified.

S&F in repair 15mm stop cock cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated with long shank and cup (concealed type), complete all as specified.

S&F in repair 500 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs including fittings, complete all as specified.

M&L for chequered tiles 30cm x 30cm x 10mm thick (Endura type), set jointed and pointed in neat cement slurry in floors with grey cement and pigments to match, including 20 mm thick screed in CM 1:6, complete all as specified.

S&F in repair curtain rod 25mm dia (outer dia) having thickness 0.63 mm, PVC powder coated of any colour/pattern, including plastic finial of 28mm bore, decorative type suitable for curtain rod, with mild steel prepainted side brackets, end cups, rings @ 10 Nos per RM and fixed with PVC rawl plugs & steel screws best quality to suit the curtain rod and fixed to the curtain rod, with suitable adhesive, complete all as specified.

M&L Preparation of old decorated plastered or unplastered by brooming down with steel wire brush, scarping down smoke soot, mould,moss and efflorescent salts and trading oil, greasy spots and applying one coat of white wash on walls including cornices, pillasters etc, complete all as specified and as directed.

M&L Preparation of old decorated plastered or unplastered surfaces by applying one coats of white wash on ceiling including cornices, pillasters etc complete all as specified and as directed.

M&L preparation of old plastered surfaces of walls and applying one coat of cement base paint over a coat of primer, complete all as specified.

M&L Preparation of old decorated plastered or unplastered by brooming down with steel wire brush, scarping down smoke soot, mould, moss and efflorescent salts and trading oil, greasy spots and applying two coats of oil bound distemper, complete all as specified and as directed.

S&F in repair Brass chromium plated shower roses 125mm size with or without swivel joints,with shower arm 15 mm dia,195 mm long with bend of 45 degree with flange of CP brass, including fixing to steel pipe or union, complete all as specified.

S&F in repair, stainless steel sinks 1 mm thick kitchen or laboratory with plugs, washers, CP coupling and waste pipe including bedding in cement mortar fixed in RCC cooking platform including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified.

S&F Stainless steel plate rack of standard pattern & of size 600 x 750 x 250 mm thickness of stainless steel sheet shall be 0.56 mm & grade of sheet shall be 304 AISI including fixing to wall with 4 Nos 50mm screws & PVC rawl plugs complete all as specified and directed.

S&F in repair, tublar Towel Rail 60cm long 'D' type between flanges of brass chromium plated 20mm dia fixed to walls, complete all as specified.

S&F in repair, PVC shelf of 450mm size, complete all as specified.

S&F in repair chromium plated Health Faucet with 450mm length PVC connection pipe for 15mm bore, complete all as specified.

S&F PVC connection 15mm size with brass nuts on both ends, 450mm long with PTMT nuts complete all as specified.

S&F 15mm bore two way bib tap fancy type, cast copper alloy with capstan head, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified.

ANUJ ABROL CONTRACTOR

AGNIHOTRI CONSTRUCTIONS

JASSI TRADERS