Construction of Fire station with staff quarters at Harni TP 1 FP 143, North Zone

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Excavation for foundation including sorting out and stacking the excavated

1 1086.75 stuff up to 50mt lead for A) Loose or soft soil Cmt 120.01

Upto 1.50 mt. depth

2 1086.75 1.50 mt.to 3.0 mt depth Cmt 133.07

3 0.00 3.0 mt to 5.0 depth Cmt 146.09

Filling available excavated Earth (Excluding Rock) in trench plinth side of

4 1449.00 foundation etc. in layer not exceeding 20 cm in depth consolidation each Cmt 133.65

deposited layer by ramming and watering etc. complete.

Disposal of Surplus excavated Earth and/or debris etc. including all lifts,

for 400 - 500 m lead outside of campus etc. complete.

Disposal of Surplus excavated Earth and/or debris etc. including all lifts,

for 5 to 10 km lead outside of campus etc. complete.

Filling in foundation and plinth with murrum or selected soil in layers of

7 341.49 20cm. thickness including watering, ramming and consolidating etc. Cmt 296.29

complete. (more than 10 ton)

Carring out plinth treatment to post construction / existing structure by

spraying chemical solution for termite control treatment including labour

and material consistment with I.S.I specification. Using Chlordene and

8 569.15 Chiorpurfiles 20 EC. As Per 6131_paret-II Consentration Weight one Smt 97.18

percent is recommended i.e one litre 20 EC chemical emulsion with 19 liter

give 1 % concrentration inclusive of one litre chemical emulsion appication

at the rate of 5 Litre chemical / Sqm of surface is recommended as per I.S

Clearing and grubbing road land including uprooting rank vegetation grass

bushes,shrubs,sapling and trees girth up to 300 mm removal of stumps of

9 0.19 Hectare 28455.09

trees cut earlier and disposal of unserviceable materials (C) By mechanical

means in area of light jungle

Providing and laying cement concrete 1:4:8 (1- Cement : 4- coarse sand : 8-

10 121.75 hand broken stone aggregates 40 mm nominal size) and curing complete Cum 2747.21

excluding cost of formwork in (A) Foundation and Plinth (upto 10 ton)

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand : 4-

graded stone aggregates 20 mm nominal size) and curing complete

excluding cost of formwork in (A) Foundation and Plinth (upto 10 ton) for

Filling in plinth with sand under floors including watering ramming,

consolidating and dressing complete (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing

complete excluding the cost of formwork and reinforcement for reinforced

concrete work in (A) Foundations, footings, Base of columns and Mass

concrete. (more than 10 ton)

Providing and laying controlled cement concrete M.250 and curing

complete excluding the cost of formwork and reinforcement for reinforced

14 11.59 concrete work in (B) Walls, from top of foundation level upto floor two Cum 4551.51

level (upto 10 ton)

LIFT WALL FROM RAFT TOP TO G.B

15 6.53 LIFT WALL FROM G.B TO F.F. SLAB Cum 4551.51

16 6.53 LIFT WALL FROM F.D TO S.F. SLAB Cum 4551.51

17 6.53 LIFT WALL FROM S.F. SLAB TO T.F. SLAB Cum 4551.51

18 6.53 LIFT WALL FROM T.F. SLAB TO F.F. SLAB Cum 4551.51

19 6.53 LIFT WALL FROM FOUR F. SLAB TO FIFTH.F. SLAB Cum 4551.51

20 6.53 LIFT WALL FROM FIFTH SLAB TO SIXTH.F SLAB Cum 4551.51

21 6.53 LIFT WALL FROM SIXTH SLAB TO SEVENTH.F SLAB Cum 4551.51

22 6.53 LIFT WALL FROM SEVENTH SLAB TO T.C F SLAB Cum 4551.51

Providing and laying in position Ready Mixed M-250 grade concrete for

reinforced cement conctere work , using cement content as per

approved Design Mix manufactured in fully automatic batching plant and

transported to site of work in transit mixer for a lead up to 10 kms

having continuous agitated mixer, manufactured as per mix design of

specified grade for reinforced cement concrete work including pumping

of R.M.C. from transit mixer to site of laying, excluding the cost of

centering shuttering finishing and reinforcement including cost of

admixtures in recommended proportions as per IS: 9103 to accelerate/

retard setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge. Without Fly

Ash (Min cement level as per latest IS 456 shall be maintained) (Cement

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

24 114.18 FF SLAB + BEAM Cum 4896.32

25 114.18 SF SLAB + BEAM Cum 4896.32

26 114.18 TF SLAB + BEAM Cum 4896.32

27 114.18 FOURTH FLOOR SLAB + BEAM Cum 4896.32

28 114.18 FIFTH FLOOR SLAB + BEAM Cum 4896.32

29 114.18 SIXTH FLOOR SLAB + BEAM Cum 4896.32

30 76.12 SEVENTH FLOOR SLAB + BEAM Cum 4896.32

31 24.35 TERRACE PARAPET WALL Cum 4896.32

32 8.70 CABIN SLAB+BEAM Cum 4896.32

Providing and laying in position Ready Mixed M-300 grade concrete for

reinforced cement conctere work , using cement content as per approved

Design Mix manufactured in fully automatic batching plant and transported

to site of work in transit mixer for a lead up to 10 kms having continuous

agitated mixer, manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of R.M.C. from transit

33 24.10 mixer to site of laying, excluding the cost of centering shuttering finishing Cum 5093.12

and reinforcement including cost of admixtures in recommended

proportions as per IS: 9103 to accelerate/ retard setting of concrete,

improve workability without impairing strength and durability as per

direction of the Engineer - in - charge. Without Fly Ash (Min cement level

as per latest IS 456 shall be maintained) (Cement level 475 kg ) OVER

ProvidingWATER TANK

and laying controlled cement concrete M.200 and curing

complete excluding the cost of formwork and reinforcement for reinforced

concrete work in (E) Staircases excluding landing upto floor two level

(more than 10 ton) Ground FLOOR STAIRCASE

35 5.34 1st FLOOR STAIRCASE Cum 5453.20

36 5.34 2nd FLOOR STAIRCASE Cum 5453.20

37 5.34 3rd FLOOR STAIRCASE Cum 5453.20

38 5.34 4th FLOOR STAIRCASE Cum 5453.20

39 5.34 5th FLOOR STAIRCASE Cum 5453.20

40 5.34 6th FLOOR STAIRCASE Cum 5453.20

41 5.34 7th FLOOR STAIRCASE Cum 5453.20

Providing and laying cement concrete work 1:2:4 (1- Cement : 2- Coarse

sand : 4- graded stone aggregates 20 mm nominal size) and curing complete

42 4.37 excluding cost of formwork and reinforcement for reinforced concrete work Cum 4023.57

in (B) shelves, Balconis , Lintels, Girders and Cantilever upto floor two

level. (more than 10 ton)

43 3.98 1st Floor Cum 4023.57

44 3.98 2nd Floor Cum 4023.57

45 3.98 3rd Floor Cum 4023.57

46 3.98 4th floor Cum 4023.57

47 3.98 5th floor Cum 4023.57

48 3.98 6th floor Cum 4023.57

49 2.65 7th floor Cum 4023.57

Providing and laying controlled cement concrete M.250 and curing

complete excluding the cost of formwork and reinforcement for reinforced

concrete work in (D) Columns, Pillars posts and struts, upto floor two level.

(more than 10 ton) G.F.

54 28.22 4th floor Cum 4628.14

55 28.22 5th Floor Cum 4628.14

56 28.22 6th floor Cum 4628.14

57 28.22 7th floor Cum 4628.14

58 3.60 STAIR CABIN + LIFT ROOM Cum 4628.14

Providing TMT Bar FE 500D reinforcement for R.C.C. work including

59 50331.32 bending, binding and placing in position complete upto floor two level Kg 77.29

Upto Plinth Level/ Foundation

60 17276.13 Ground Floor Kg 77.29

61 17248.72 1st Floor Kg 77.29

62 17248.72 2nd Floor Kg 77.29

63 17248.72 3rd Floor Kg 77.29

64 17248.72 4th floor Kg 77.29

65 17248.72 5th Floor Kg 77.29

66 17248.72 6th floor Kg 77.29

67 17248.72 7th floor Kg 77.29

68 2435.23 TERRACE PARAPET WALL Kg 77.29

69 4003.52 STAIR CABIN + LIFT ROOM Kg 77.29

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Providing formwork of ordinary timber planking so as to give a rough

finish including centering, shuttering and propping etc. height of propping

70 1408.96 and centering below supporting floor to ceiling not exceeding 4.00 mts and Sqm 179.36

removal of the same for in situ reinforced cement concrete works.

A) Foundation and plinth

(B) Flat surfaces such as soffits of supspened floors slabs Landings and the

like. (1) Floors etc. upto 200 mm in thickness. (more than 10 ton)

72 1181.80 (C) Vertical surface such as walls (any thickness) partitions Sqm 239.69

(G) Columns PillarsPosts and struts. (1) Square Rectangular Polygonal in

plan. (upto 10 ton)

(H) (1) Sides and soffits of Beams Beam Haunchings cantilevers Girders

Bressumers and Lintels not exceeding 1 M. in Depth. (upto 10 ton)

(M) Staircase with sloping or stepped soffits including risers and stringers

excluding landing. (upto 10 ton)

76 523.06 (I) Edges of slabs and Breaks in floors and walls. (upto 10 ton) Sqm 71.59

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:6 (1- Cement : 6 -fine sand)(A) Modular (upto 10 ton)

In foundation and plinth

78 7.73 GROUND FLOOR. Cmt 4498.19

79 135.17 1st FLOOR. Cmt 4498.19

80 135.17 2nd FLOOR. Cmt 4498.19

81 135.17 3rd FLOOR. Cmt 4498.19

82 135.17 4th FLOOR Cmt 4498.19

83 135.17 5th FLOOR Cmt 4498.19

84 135.17 6th FLOOR Cmt 4498.19

85 92.48 7th FLOOR Cmt 4498.19

86 16.56 Terrace level Cmt 4498.19

(ii) Half brick masonry in common brunt clay building bricks having

crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:5 (1-

87 16.80 Cement : 5 -coarse sand ) in foundation and plinth (A) Modular (upto 10 Smt. 595.67

88 90.73 1st FLOOR. Smt. 595.67

89 90.73 2nd FLOOR. Smt. 595.67

90 90.73 3rd FLOOR. Smt. 595.67

91 90.73 4th Floor Smt. 595.67

92 90.73 5th Floor Smt. 595.67

93 90.73 6th floor Smt. 595.67

94 60.49 7th floor Smt. 595.67

Providing 15mm thick cement plaster in single coat on Rough (Similar)side

of single or half brick walls for interior plastering upto floor two level and

finished even and smooth in (i) Cement mortar 1:4 (1-cement:3-sand)

96 1304.41 1st FLOOR. Smt. 171.21

97 1304.41 2nd FLOOR. Smt. 171.21

98 1304.41 3rd FLOOR. Smt. 171.21

99 1304.41 4th Floor Smt. 171.21

100 1304.41 5th Floor Smt. 171.21

101 1304.41 6Th floor Smt. 171.21

102 897.71 7th floor Smt. 171.21

103 348.25 T.C. AND PERAPET+ LIFT ROOM Smt. 171.21

Providing 10mm thick cement plaster in single coat on Rough (Similar)side

104 399.38 CEILINGs for interior plastering upto floor two level and finished even and Smt. 196.64

smooth in (i) Cement mortar 1:3 (1-cement:3-sand) GROUND FLOOR

105 399.38 1st FLOOR. Smt. 196.64

106 399.38 2nd FLOOR. Smt. 196.64

107 399.38 3rd FLOOR. Smt. 196.64

108 399.38 4th Floor Smt. 196.64

109 399.38 5th Floor Smt. 196.64

110 399.38 6th floor Smt. 196.64

111 277.81 7th floor Smt. 196.64

112 30.90 T.C. AND PERAPET+ LIFT ROOM Smt. 196.64

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

20mm thick sand faced cement plaster on walls upto height 10 metres

above ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-

cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-

sand) etc. complete. GROUND FLOOR.

114 629.70 1st FLOOR. Smt. 338.53

115 629.70 2nd FLOOR. Smt. 339.54

116 629.70 3rd FLOOR. Smt. 340.55

117 629.70 4th Floor Smt. 341.56

118 629.70 5th Floor Smt. 342.57

119 629.70 6th floor Smt. 343.58

120 591.45 7th floor Smt. 344.59

121 327.65 T.C. AND PERAPET+ LIFT ROOM Smt 337.52

Provoding and fixing Before plaster work Chicken wire mesh 16 x24 OR

122 3000.00 Fiber Chicken mesh (1meter width x 50 meter length waterproofing crack Smt. 184.02

patch work and etc

Applying two coats of Birla or Asian (or equivalent) acrylic lapy ( putty) &

two coats of primer of approved brand and manufacture on new wall

123 536.41 surface to give an even shade including thoroughly brushing the surface Smt 40.59

free from mortar dropping and other foreign matter and sand papered

smooth. GROUND FLOOR.

124 1703.78 1st FLOOR. Smt 40.59

125 1703.78 2nd FLOOR. Smt 40.59

126 1703.78 3rd FLOOR. Smt 40.59

127 1703.78 4th Floor Smt 40.59

128 1703.78 5th Floor Smt 40.59

129 1703.78 6th floor Smt 40.59

130 1175.52 7th floor Smt 40.59

131 379.15 T.C. AND PERAPET+ LIFT ROOM Smt 40.59

Wall painting (two coats) with plastic emulsion paint of approved brand

and manufacture on undecorated wall surface to give an even shade

132 536.41 including throughly brushing the surface free from mortar droppings and Smt 80.87

other foreign matter and sand papered smooth. + Extra over for every

subsequent coat of wall painting with plastic emulsion pain of approved

brand. GROUND FLOOR.

133 1703.78 1st FLOOR. Smt 80.87

134 1703.78 2nd FLOOR. Smt 80.87

135 1703.78 3rd FLOOR. Smt 80.87

136 1703.78 4th Floor Smt 80.87

137 1703.78 5th Floor Smt 80.87

138 1703.78 6th floor Smt 80.87

139 1175.52 7th floor Smt 80.87

140 379.15 T.C. AND PERAPET+ LIFT ROOM Smt 80.87

Finishing Wall with weather proof exterior plastic emulsion paint on wall

surface (two coats) to give an required shape even shade after thoroughly

brushing surface to remove all dirt and remains of loose powdered

materials etc comp. for all height. GROUND FLOOR

142 629.70 1st FLOOR. Smt 117.40

143 629.70 2nd FLOOR. Smt 117.40

144 629.70 3rd FLOOR. Smt 117.40

145 629.70 4th Floor Smt 117.40

146 629.70 5th Floor Smt 117.40

147 629.70 6th floor Smt 117.40

148 591.45 7th floor Smt 117.40

149 327.65 T.C. AND PERAPET+ LIFT ROOM Smt 117.40

Painting two coats (excluding priming coat) on new steel and other metal

surface with enamel paint, brushing, interior to give an even shade

including cleaning the surface an even shade including cleanicn the surface

of all dirt, dust and other foreign matter.

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average)

base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or

151 2289.84 fixing on existing flooring by adhesive material including dismentaling of Smt 1452.79

existing flooring and jointed with color cement slurry including finised with

flush pointing & cleaning the surface etc. complete for light shade (upto

Providing and laying white glazed tiles 6mm thick in flooring treads of

152 204.33 steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement Smt 983.20

: 3-coarse sand ) finishing with flush pointing in white cement. (upto 10 ton)

Providing and laying white glazed tiles 6mm thick in skrting risers of steps

153 1266.52 and dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and Smt 1022.34

jointed with white cement slurry (upto 10 ton)

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Providing and laying polished kota stone slab 25mm thick in risers of

steps,skirting Dedo and pillars laid on 10mm thick cement mortar 1:3 (1-

154 397.04 Cement : 3 coarse sand) and jointed with gray cement slury mixed with Smt 1149.52

pigment to match the shade of slab including rubbing and polishing etc.

complete. (upto 10 ton)

Providing and laying cement concrete 1:3:6 (1- Cement : 3- Coarse sand : 6-

Graded brick bat aggregate 40mm normal size) and curing complete

excluding cost of formwork in slopes terrace for area for water proofing

work as directed by EIC.

Providing and laying broken chine mosaic flooring for terrace using 12 mm

to 20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to

plain or slope and to be tempered to bring mortar creme out upto surface

156 492.44 using white cement including rounding off junctions and extending them Smt 765.97

upto 15 cm along the wall,clearing with water and oxalic acid and

including using water proofing material at the rate of 1 Kg./bag of cement.

etc. for water proofing work as directed by EIC.

Preparing and applying of water soluble, nonflammable, reactive and

penetrative silane nanotechnology with water (<1000 ppm TDS) in the ratio

of 1 liter silane :20 liter water mixed with 0.5 liter acrylic copolymer

polymer compatible and stable in silane solution. Take 1 liter of silane

nanotechnology and add in 20 liter water in drum under manual stirring and

157 732.14 then add 0.5 liter acrylic copolymer under manual stirring and mix Smt 81.27

completely. Spray apply the solution at the rate of 1 liter per sqm on

horizontal and 0.5 liter per sqm on vertical new or old cementitious /

concrete surface . (For very dense concrete of M50 and above for bridges

may not absorb 1 liter per sq meter so reduce the water of dilution to

1:10)Horizonal Surface

Providing cement vata (10cm. x 10 cm. size) quarter round in cement

mortar 1:1 including neat cement finishing, watering etc. complete.

P/F 25 mm. Thick Polished Granite kotah stone sandwitch type platform

0.75 width & 0.70 m height resting on single/ double polished kotah stone

159 98.66 of 25 mm thick in C.M. 1:4 with Granite stone of 25 mm thick with SMT 3680.51

cupboard shelves polished kotah stone etc. comp. As per Architect

instructions and drawing or as directed by engineer in charge..

Providing and fixing Kitchen sink with C.I. or M.S. brackets, painted white

including cutting holes in walls and making good the same but excluding

160 40.00 fittings. (C) Stainless steel Sink.(i) 600mm x 450mm x 150mm size EACH 2326.66

(NIRALI, HINDWARE etc..) INCL. all fittings and fixtures etc. all

complete as directed by EIC.

Provoding and fixing flush door shutters, solid core construction with frame

of first class hardwood with cross board and face veneer or plywood face

161 443.10 panels, including anodised alluminium butt hinges with necessary screws. SQM 1829.74

(B) Non-decorative type and block board core anodised alluminium butt

hinges in flush door shutters (2) 35 mm thick.

(B) Non-decorative type and block board core anodised alluminium butt

hinges in flush door shutters (2) 35 mm thick. With laminated sheet

mm Thick Architect instructions and drawing or as directed by engineer in

Providing Jodhpuri / Dholpuri frames of Doors, windows cleare story

windows and othersimilar works wrought, framede and fixed in position.

Thick 4'',6'', 8'' inch As per tender spacified or as directed by engineer in

Providing and fixing 35mm thick factory made moulded door shuter

consisting of solid core single leaf flush door of 30mm thickness, lipped

with 15mm (5mm x 3) thick x 30mm width on one stiles and top rail and

10mm (5mm x 2) thick x 30mm width on the other stiles and bottom rails.

The inner panel laminated with 2mm thick termite proof, water proof and

fire resistant moulded PVC sheet with 2,4,6 raised panel design in different

164 126.00 plain and /or prelim colours on one side after routing the moulded design on Sqm 2152.31

flush door and 2mm plain and/or prelim PVC sheet on other side using

rubber adhesive on flush door and solvent cement adhesive on the PVC

liping etc. complete as per direction of Engineer in charge, manufacture’s

specification and drawing.

D3 FOR BATH AND W.C.

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Providing and fixing window having extruded aluminum Colour anodized

section frame main outer size 63.50 x 38.10 x 1.95 mm(of Jindal Section

no:4605,@ Wt 1.094 Kg / Rmt), horizontal two track member size

mm x 31.75 mm x 1.20mm (of Jindal Section no: 8687 @ wt.of

Kg/mt), vertical member of size 61.85 mm x 31.75mm x 1.30 mm (of

Jindal Section no:8758 @ wt.of 0.0.659 Kg/mt) with sliding shutters of

165 194.40 horizontal member size 40mm x 18mm x 1.29mm (of Jindal Section smt 1713.70

no:8949 @ wt.of 0.456Kg/mt), vertical member of size 40mm x 18mm x

1.29mm (of Jindal Section no:8947 @ wt.of 0.456Kg/mt/ Section 8948, @

Wt. 0.457 Kg/mt) with 5 mm thick transparent bronze colour tinted float

glass with powder coated aluminum fittings and fixtures and transparent

silicon sealant glass fixing to frame as per details etc complete for window.

Providing and fixing windows black polished granite AS per tender

specification and directed by engineer in charge

Providing and fixing M.S. grills of required pattern to wooden frames of

windows etc. with M.S. flats at required spacings and frame alround,

square or round bars with round headed bolts and nuts or by screws (A)

Plain Grill. (upto 10 ton)

Providing laying and jointing in true line and level 15mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

168 424.00 In Charge. Pipe shall be fixed on the wall with the help of clamp at every RMT 72.65

two metre C/C or shall be concelled as directed including necessary fittings

etc. including testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

169 244.00 In Charge. Pipe shall be fixed on the wall with the help of clamp at every RMT 91.84

two metre C/C or shall be concelled as directed including necessary fittings

etc. including testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Providing laying and jointing in true line and level 32mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

170 480.00 In Charge. Pipe shall be fixed on the wall with the help of clamp at every RMT 119.15

two metre C/C or shall be concelled as directed including necessary fittings

etc. including testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Providing laying and jointing in true line and level 40mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

171 560.00 In Charge. Pipe shall be fixed on the wall with the help of clamp at every RMT 148.12

two metre C/C or shall be concelled as directed including necessary fittings

etc. including testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Providing laying and jointing in true line and level 50mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

172 190.50 In Charge. Pipe shall be fixed on the wall with the help of clamp at every RMT 195.67

two metre C/C or shall be concelled as directed including necessary fittings

etc. including testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Providing and fixing concealed center point to wall ceiling & floor CPVC

(SDR 13.5) PIPE having National Sanitation Foundation (NSF)

173 100.00 seal for potable water of following dia. nominal bore tube fittings and RMT 208.80

clamps including making good the wall, ceiling and floor etc. complete.

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working

pressure polythene pipes of the following outside Dia. Low densidy,

complete with special falnge compression type fittings, wall clipsetc.

including making good the wall ceiling and floor. (F) 75mm

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working

pressure poluthene pipes of the following outside Dia. Low densidy,

complete with special falnge compression type fittings, wall clipsetc.

including making good the wall ceiling and floor.(G)110 mm.

176 6.00 Providing and fixing in position cowel went to pipes.(B) 75mm dia. EACH 393.04

177 6.00 Providing and fixing in position cowel went to pipes.(C) 110mm dia EACH 505.17

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm

diameter with jali of the following nominal diameter of self cleansing

design with C.I scread down or hinged grating including the cost of cutting

and making good the walls.

Providing and fixing S.W. gully trap with C.I. grating brick masonry

chamber and water tight C.I. cover with frame of 300mm x 300mm size

(inside) with standard weight.(i) Square mouth traps. (A) 100mm x 100mm

size P type. (upto 10 ton)

Providing and laying (to level or slopes) and jointing with stiff mixture of

180 40.00 Cement Mortar in proportion 1:1 Selt glazed stoneware pipes including RMT 312.76

testing of pipes and joints complete.(B) 150mm dia. (upto 10 ton)

Providing and fixing water closet squatting Pan( EUROPEON type W.C.

181 40.00 Pan) (Earthwork, bed concrete, foot reste and trap to be measured and paid EACH 1336.30

for separately) (A) Vitreous China.(I) Long pattern = White colour

Providing and fixing plastic seat and cover for wash down water closer

with C.P. brass hinges and rubber buffers. (B) Black plastic seal and cover.

Providing and fixing Gun metal check or non-return fullway wheel

valve.(E) 40mm dia.

Providing and fixing Gun metal check or non-return fullway wheel

valve.(D) 32 mm dia.

Providing and fixing screw down bib taps of following size.(A) Brass

screw down bib tap polished bright. (i) 15mm dia.

Providing and fixing washbasin with single hole for pillar tap with C.I. or

M.S. brackets painted white including sutting holes and making good the

same but excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin

550 mm x v 400mm size. (i) In white colour.

187 40.00 Providing and fixing C.P. brass waste for washbasin or sink. (B) 40mm dia. EACH 89.83

188 40.00 Providing and fixing M.I. fisher union for washbasin or sink. (B) 40mm dia. EACH 88.65

Providing and fixing 100mm sand cast iron grating for gully, floor or Nahni

Providing and fixing C.P. brass shower rose with 15mm or 20mm inlet.(A)

100mm dia. Each

Providing and fixing chromium plated brass half trun flush cock of

approved quality including fixing in pipe line etc. complete.(ii) 25mm dia.

Providing and fixing M.S. fan clamps of shape and size as specified in

existing R.C.C. slab including cutting chase and making good.

Providing and fixing pillar tap, capstan head, screw down high pressure

with screws, shanks and back nuts. (i) 15mm dia.

Excavation for foundation including sorting out and stacking the excavated

stuff up to 50mt lead for A) Loose or soft soil Upto 1.50 mt. depth

195 3505.95 1.50 mt.to 3.0 mt depth Cmt 133.07

196 0.00 3.0 mt to 5.0 depth Cmt 146.09

Filling available excavated Earth (Excluding Rock) in trench plinth side of

197 4674.60 foundation etc. in layer not exceeding 20 cm in depth consolidation each Cmt 133.65

deposited layer by ramming and watering etc. complete.

Disposal of Surplus excavated Earth and/or debris etc. including all lifts,

for 400 - 500 m lead outside of campus etc. complete.

Disposal of Surplus excavated Earth and/or debris etc. including all lifts,

for 5 to 10 km lead outside of campus etc. complete.

Filling in foundation and plinth with murrum or selected soil in layers of

200 1222.65 20cm. thickness including watering, ramming and consolidating etc. Cmt 296.29

complete. (more than 10 ton)

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Carring out plinth treatment to post construction / existing structure by

spraying chemical solution for termite control treatment including labour

and material consistment with I.S.I specification. Using Chlordene and

201 2037.75 Chiorpurfiles 20 EC. As Per 6131_paret-II Consentration Weight one Smt 97.18

percent is recommended i.e one litre 20 EC chemical emulsion with 19 liter

give 1 % concrentration inclusive of one litre chemical emulsion appication

at the rate of 5 Litre chemical / Sqm of surface is recommended as per I.S

Clearing and grubbing road land including uprooting rank vegetation grass

bushes,shrubs,sapling and trees girth up to 300 mm removal of stumps of

trees cut earlier and disposal of unserviceable materials (C) By mechanical

means in area of light jungle

Providing and laying cement concrete 1:4:8 (1- Cement : 4- coarse sand : 8-

203 413.82 hand broken stone aggregates 40 mm nominal size) and curing complete Cum 2747.21

excluding cost of formwork in (A) Foundation and Plinth (upto 10 ton)

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand : 4-

graded stone aggregates 20 mm nominal size) and curing complete

excluding cost of formwork in (A) Foundation and Plinth (upto 10 ton) for

Filling in plinth with sand under floors including watering ramming,

consolidating and dressing complete (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing

complete excluding the cost of formwork and reinforcement for reinforced

concrete work in (A) Foundations, footings, Base of columns and Mass

concrete. (more than 10 ton)

Providing and laying controlled cement concrete M.250 and curing

complete excluding the cost of formwork and reinforcement for reinforced

concrete work in (B) Walls, from top of foundation level upto floor two

level (upto 10 ton) LIFT WALL FROM RAFT TOP TO G.B

208 14.74 LIFT WALL FROM G.B TO F.F. SLAB Cum 4551.51

209 14.74 LIFT WALL FROM F.F TO S.F. SLAB Cum 4551.51

210 14.74 LIFT WALL FROM S.F. SLAB TO T.F. SLAB Cum 4551.51

211 14.74 LIFT WALL FROM T.F. SLAB TO F.F. SLAB Cum 4551.51

212 14.74 LIFT WALL FROM FOUR F. SLAB TO T.C SLAB Cum 4551.51

Providing and laying in position Ready Mixed M-250 grade concrete for

reinforced cement conctere work , using cement content as per

approved Design Mix manufactured in fully automatic batching plant and

transported to site of work in transit mixer for a lead up to 10 kms

having continuous agitated mixer, manufactured as per mix design of

specified grade for reinforced cement concrete work including pumping

of R.M.C. from transit mixer to site of laying, excluding the cost of

centering shuttering finishing and reinforcement including cost of

admixtures in recommended proportions as per IS: 9103 to accelerate/

retard setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge. Without Fly

Ash (Min cement level as per latest IS 456 shall be maintained) (Cement

214 340.23 FF SLAB + BEAM Cum 4896.32

215 210.60 SF SLAB + BEAM Cum 4896.32

216 196.03 TF SLAB + BEAM Cum 4896.32

217 196.03 FOURTH FLOOR SLAB + BEAM Cum 4896.32

218 24.35 TERRACE PARAPET WALL Cum 4896.32

219 8.98 CABIN SLAB+BEAM Cum 4896.32

Providing and laying in position Ready Mixed M-300 grade concrete for

reinforced cement conctere work , using cement content as per approved

Design Mix manufactured in fully automatic batching plant and transported

to site of work in transit mixer for a lead up to 10 kms having continuous

agitated mixer, manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of R.M.C. from transit

220 24.10 mixer to site of laying, excluding the cost of centering shuttering finishing Cum 5093.12

and reinforcement including cost of admixtures in recommended

proportions as per IS: 9103 to accelerate/ retard setting of concrete,

improve workability without impairing strength and durability as per

direction of the Engineer - in - charge. Without Fly Ash (Min cement level

as per latest IS 456 shall be maintained) (Cement level 475 kg ) OVER

HEAD WATER TANK

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Providing and laying controlled cement concrete M.200 and curing

complete excluding the cost of formwork and reinforcement for reinforced

concrete work in (E) Staircases excluding landing upto floor two level

(more than 10 ton) Ground FLOOR STAIRCASE

222 9.99 1st FLOOR STAIRCASE Cum 5453.20

223 9.99 2nd FLOOR STAIRCASE Cum 5453.20

224 5.34 3rd FLOOR STAIRCASE Cum 5453.20

225 5.34 4th FLOOR STAIRCASE Cum 5453.20

Providing and laying cement concrete work 1:2:4 (1- Cement : 2- Coarse

sand : 4- graded stone aggregates 20 mm nominal size) and curing complete

226 3.25 excluding cost of formwork and reinforcement for reinforced concrete work Cum 4023.57

in (B) shelves, Balconis , Lintels, Girders and Cantilever upto floor two

level. (more than 10 ton) Ground Floor

227 2.82 1st Floor Cum 4023.57

228 4.43 2nd Floor Cum 4023.57

229 4.31 3rd Floor Cum 4023.57

230 4.31 4th floor Cum 4023.57

Providing and laying controlled cement concrete M.250 and curing

complete excluding the cost of formwork and reinforcement for reinforced

concrete work in (D) Columns, Pillars posts and struts, upto floor two level.

(more than 10 ton) G.F.

235 33.26 4th floor Cum 4628.14

236 3.60 STAIR CABIN + LIFT ROOM Cum 4628.14

Providing TMT Bar FE 500D reinforcement for R.C.C. work including

237 77693.83 bending, binding and placing in position complete upto floor two level Kg 77.29

Upto Plinth Level/ Foundation

238 22903.36 Ground Floor Kg 77.29

243 2435.23 TERRACE PARAPET WALL Kg 77.29

244 4035.14 STAIR CABIN + LIFT ROOM Kg 77.29

Providing formwork of ordinary timber planking so as to give a rough

finish including centering, shuttering and propping etc. height of propping

245 2044.39 and centering below supporting floor to ceiling not exceeding 4.00 mts and Sqm 179.36

removal of the same for in situ reinforced cement concrete works.

A) Foundation and plinth

(B) Flat surfaces such as soffits of supspened floors slabs Landings and the

like. (1) Floors etc. upto 200 mm in thickness. (more than 10 ton)

247 1026.32 (C) Vertical surface such as walls (any thickness) partitions Sqm 239.69

(G) Columns PillarsPosts and struts. (1) Square Rectangular Polygonal in

plan. (upto 10 ton)

(H) (1) Sides and soffits of Beams Beam Haunchings cantilevers Girders

Bressumers and Lintels not exceeding 1 M. in Depth. (upto 10 ton)

(M) Staircase with sloping or stepped soffits including risers and stringers

excluding landing. (upto 10 ton)

251 1047.00 (I) Edges of slabs and Breaks in floors and walls. (upto 10 ton) Sqm 71.59

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:6 (1- Cement : 6 -fine sand)(A) Modular (upto 10 ton) In

foundation and plinth

253 330.15 GROUND FLOOR. Cmt 4498.19

255 167.48 2nd FLOOR. Cmt 4498.19

256 221.92 3rd FLOOR. Cmt 4498.19

257 221.92 4th FLOOR Cmt 4498.19

258 34.94 Terrace level Cmt 4498.19

(ii) Half brick masonry in common brunt clay building bricks having

crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:5 (1-

259 16.80 Cement : 5 -coarse sand ) in foundation and plinth (A) Modular (upto 10 Smt. 595.67

260 151.49 1st FLOOR. Smt. 595.67

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

261 151.49 2nd FLOOR. Smt. 595.67

262 151.49 3rd FLOOR. Smt. 595.67

263 151.49 4th Floor Smt. 595.67

Providing 15mm thick cement plaster in single coat on Rough (Similar)side

of single or half brick walls for interior plastering upto floor two level and

finished even and smooth in (i) Cement mortar 1:4 (1-cement:3-sand)

268 1546.49 4th Floor Smt. 171.21

269 309.12 T.C. AND PERAPET+ LIFT ROOM Smt. 171.21

Providing 10mm thick cement plaster in single coat on Rough (Similar)side

270 6269.82 CEILINGs for interior plastering upto floor two level and finished even and Smt. 196.64

smooth in (i) Cement mortar 1:3 (1-cement:3-sand)

20mm thick sand faced cement plaster on walls upto height 10 metres

above ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-

cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-

sand) etc. complete.

Provoding and fixing Before plaster work Chicken wire mesh 16 x24 OR

272 1250.00 Fiber Chicken mesh (1meter width x 50 meter length waterproofing crack Smt. 184.02

patch work and etc

Applying two coats of Birla or Asian (or equivalent) acrylic lapy ( putty) &

two coats of primer of approved brand and manufacture on new wall

273 13449.37 surface to give an even shade including thoroughly brushing the surface Smt 40.59

free from mortar dropping and other foreign matter and sand papered

Wall painting (two coats) with plastic emulsion paint of approved brand

and manufacture on undecorated wall surface to give an even shade

274 4266.55 including throughly brushing the surface free from mortar droppings and Smt 80.87

other foreign matter and sand papered smooth. + Extra over for every

subsequent coat of wall painting with plastic emulsion pain of approved

Finishing Wall with weather proof exterior plastic emulsion paint on wall

surface (two coats) to give an required shape even shade after thoroughly

brushing surface to remove all dirt and remains of loose powdered

materials etc comp. for all height.

Painting two coats (excluding priming coat) on new steel and other metal

surface with enamel paint, brushing, interior to give an even shade

including cleaning the surface an even shade including cleanicn the surface

of all dirt, dust and other foreign matter.

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average)

base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or

277 1756.07 fixing on existing flooring by adhesive material including dismentaling of Smt 1452.79

existing flooring and jointed with color cement slurry including finised with

flush pointing & cleaning the surface etc. complete for light shade (upto

Providing and laying white glazed tiles 6mm thick in flooring treads of

278 159.04 steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement Smt 983.20

: 3-coarse sand ) finishing with flush pointing in white cement. (upto 10 ton)

Providing and laying white glazed tiles 6mm thick in skrting risers of steps

279 445.60 and dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and Smt 1022.34

jointed with white cement slurry (upto 10 ton)

Providing and laying polished kota stone slab 25mm thick in risers of

steps,skirting Dedo and pillars laid on 10mm thick cement mortar 1:3 (1-

280 387.02 Cement : 3 coarse sand) and jointed with gray cement slury mixed with Smt 1149.52

pigment to match the shade of slab including rubbing and polishing etc.

complete. (upto 10 ton)

Providing and laying cement concrete 1:3:6 (1- Cement : 3- Coarse sand : 6-

Graded brick bat aggregate 40mm normal size) and curing complete

excluding cost of formwork in slopes terrace for area for water proofing

work as directed by EIC.

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Providing and laying broken chine mosaic flooring for terrace using 12 mm

to 20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to

plain or slope and to be tempered to bring mortar creme out upto surface

282 1013.21 using white cement including rounding off junctions and extending them Smt 765.97

upto 15 cm along the wall,clearing with water and oxalic acid and

including using water proofing material at the rate of 1 Kg./bag of cement.

etc. for water proofing work as directed by EIC.

Preparing and applying of water soluble, nonflammable, reactive and

penetrative silane nanotechnology with water (<1000 ppm TDS) in the ratio

of 1 liter silane :20 liter water mixed with 0.5 liter acrylic copolymer

polymer compatible and stable in silane solution. Take 1 liter of silane

nanotechnology and add in 20 liter water in drum under manual stirring and

283 1069.64 then add 0.5 liter acrylic copolymer under manual stirring and mix Smt 81.27

completely. Spray apply the solution at the rate of 1 liter per sqm on

horizontal and 0.5 liter per sqm on vertical new or old cementitious /

concrete surface . (For very dense concrete of M50 and above for bridges

may not absorb 1 liter per sq meter so reduce the water of dilution to

1:10)Horizonal Surface

Providing cement vata (10cm. x 10 cm. size) quarter round in cement

mortar 1:1 including neat cement finishing, watering etc. complete.

P/F 25 mm. Thick Polished Granite kotah stone sandwitch type platform

0.75 width & 0.70 m height resting on single/ double polished kotah stone

285 104.94 of 25 mm thick in C.M. 1:4 with Granite stone of 25 mm thick with SMT 3680.51

cupboard shelves polished kotah stone etc. comp. As per Architect

instructions and drawing or as directed by engineer in charge..

Providing and fixing Kitchen sink with C.I. or M.S. brackets, painted white

including cutting holes in walls and making good the same but excluding

286 8.00 fittings. (C) Stainless steel Sink.(i) 600mm x 450mm x 150mm size EACH 2326.66

(NIRALI, HINDWARE etc..) INCL. all fittings and fixtures etc. all

complete as directed by EIC.

Provoding and fixing flush door shutters, solid core construction with frame

of first class hardwood with cross board and face veneer or plywood face

287 169.16 panels, including anodised alluminium butt hinges with necessary screws. SQM 1829.74

(B) Non-decorative type and block board core anodised alluminium butt

hinges in flush door shutters (2) 35 mm thick.

(B) Non-decorative type and block board core anodised alluminium butt

hinges in flush door shutters (2) 35 mm thick. With laminated sheet

mm Thick Architect instructions and drawing or as directed by engineer in

Providing Jodhpuri / Dholpuri frames of Doors, windows cleare story

windows and othersimilar works wrought, framede and fixed in position.

Thick 4'',6'', 8'' inch As per tender spacified or as directed by engineer in

Providing and fixing 35mm thick factory made moulded door shuter

consisting of solid core single leaf flush door of 30mm thickness, lipped

with 15mm (5mm x 3) thick x 30mm width on one stiles and top rail and

10mm (5mm x 2) thick x 30mm width on the other stiles and bottom rails.

The inner panel laminated with 2mm thick termite proof, water proof and

fire resistant moulded PVC sheet with 2,4,6 raised panel design in different

290 91.35 plain and /or prelim colours on one side after routing the moulded design on Sqm 2152.31

flush door and 2mm plain and/or prelim PVC sheet on other side using

rubber adhesive on flush door and solvent cement adhesive on the PVC

liping etc. complete as per direction of Engineer in charge, manufacture’s

specification and drawing.

D3 FOR BATH AND W.C.

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Providing and fixing window having extruded aluminum Colour anodized

section frame main outer size 63.50 x 38.10 x 1.95 mm(of Jindal Section

no:4605,@ Wt 1.094 Kg / Rmt), horizontal two track member size

mm x 31.75 mm x 1.20mm (of Jindal Section no: 8687 @ wt.of

Kg/mt), vertical member of size 61.85 mm x 31.75mm x 1.30 mm (of

Jindal Section no:8758 @ wt.of 0.0.659 Kg/mt) with sliding shutters of

291 56.94 horizontal member size 40mm x 18mm x 1.29mm (of Jindal Section smt 1713.70

no:8949 @ wt.of 0.456Kg/mt), vertical member of size 40mm x 18mm x

1.29mm (of Jindal Section no:8947 @ wt.of 0.456Kg/mt/ Section 8948, @

Wt. 0.457 Kg/mt) with 5 mm thick transparent bronze colour tinted float

glass with powder coated aluminum fittings and fixtures and transparent

silicon sealant glass fixing to frame as per details etc complete for window.

Providing and fixing windows black polished granite AS per tender

specification and directed by engineer in charge

Providing and fixing M.S. grills of required pattern to wooden frames of

windows etc. with M.S. flats at required spacings and frame alround,

square or round bars with round headed bolts and nuts or by screws (A)

Plain Grill. (upto 10 ton)

Providing laying and jointing in true line and level 15mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

294 119.40 In Charge. Pipe shall be fixed on the wall with the help of clamp at every RMT 72.65

two metre C/C or shall be concelled as directed including necessary fittings

etc. including testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

295 96.00 In Charge. Pipe shall be fixed on the wall with the help of clamp at every RMT 91.84

two metre C/C or shall be concelled as directed including necessary fittings

etc. including testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Providing laying and jointing in true line and level 32mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

296 119.00 In Charge. Pipe shall be fixed on the wall with the help of clamp at every RMT 119.15

two metre C/C or shall be concelled as directed including necessary fittings

etc. including testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Providing laying and jointing in true line and level 40mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

297 137.50 In Charge. Pipe shall be fixed on the wall with the help of clamp at every RMT 148.12

two metre C/C or shall be concelled as directed including necessary fittings

etc. including testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Providing laying and jointing in true line and level 50mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

298 204.50 In Charge. Pipe shall be fixed on the wall with the help of clamp at every RMT 195.67

two metre C/C or shall be concelled as directed including necessary fittings

etc. including testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Providing and fixing concealed center point to wall ceiling & floor CPVC

(SDR 13.5) PIPE having National Sanitation Foundation (NSF)

299 55.00 seal for potable water of following dia. nominal bore tube fittings and RMT 208.80

clamps including making good the wall, ceiling and floor etc. complete.

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working

pressure polythene pipes of the following outside Dia. Low densidy,

complete with special falnge compression type fittings, wall clipsetc.

including making good the wall ceiling and floor. (F) 75mm

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working

pressure poluthene pipes of the following outside Dia. Low densidy,

complete with special falnge compression type fittings, wall clipsetc.

including making good the wall ceiling and floor.(G)110 mm.

302 8.00 Providing and fixing in position cowel went to pipes.(B) 75mm dia. EACH 393.04

303 8.00 Providing and fixing in position cowel went to pipes.(C) 110mm dia EACH 505.17

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm

diameter with jali of the following nominal diameter of self cleansing

design with C.I scread down or hinged grating including the cost of cutting

and making good the walls.

Providing and fixing S.W. gully trap with C.I. grating brick masonry

chamber and water tight C.I. cover with frame of 300mm x 300mm size

(inside) with standard weight.(i) Square mouth traps. (A) 100mm x 100mm

size P type. (upto 10 ton)

Providing and laying (to level or slopes) and jointing with stiff mixture of

306 60.00 Cement Mortar in proportion 1:1 Selt glazed stoneware pipes including RMT 312.76

testing of pipes and joints complete.(B) 150mm dia. (upto 10 ton)

Providing and fixing water closet squatting Pan( EUROPEON type W.C.

307 12.00 Pan) (Earthwork, bed concrete, foot reste and trap to be measured and paid EACH 1336.30

for separately) (A) Vitreous China.(I) Long pattern = White colour

Providing and fixing plastic seat and cover for wash down water closer

with C.P. brass hinges and rubber buffers. (B) Black plastic seal and cover.

Providing and fixing Gun metal check or non-return fullway wheel

valve.(E) 40mm dia.

Providing and fixing Gun metal check or non-return fullway wheel

valve.(D) 32 mm dia.

Providing and fixing screw down bib taps of following size.(A) Brass

screw down bib tap polished bright. (i) 15mm dia.

Providing and fixing washbasin with single hole for pillar tap with C.I. or

M.S. brackets painted white including sutting holes and making good the

same but excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin

550 mm x v 400mm size. (i) In white colour.

313 20.00 Providing and fixing C.P. brass waste for washbasin or sink. (B) 40mm dia. EACH 89.83

314 20.00 Providing and fixing M.I. fisher union for washbasin or sink. (B) 40mm dia. EACH 88.65

Providing and fixing 100mm sand cast iron grating for gully, floor or Nahni

Providing and fixing C.P. brass shower rose with 15mm or 20mm inlet.(A)

100mm dia. Each

Providing and fixing chromium plated brass half trun flush cock of

approved quality including fixing in pipe line etc. complete.(ii) 25mm dia.

318 12.00 Providing and fixing G.I. inlet connection for flush pipe with W.C. Pan EACH 39.78

Providing and fixing pillar tap, capstan head, screw down high pressure

with screws, shanks and back nuts. (i) 15mm dia.

Providing and fixing Urinal of approved quality including

connection with trap and with integral longitudinal flush

pipe.(A) Squating plate pattern white earthenware 550mm

Providing and laying tactile tile (for vision impaired persons as per

standards) of size 300x300x9.8 mm having with water absorption less

than 0.5% and conforming to IS:15622 of approved make in all colours

and shades in for outdoor floors such as footpath, court yard, multi

321 270.00 modals location etc., laid on 20 mm thick base of cement mortar 1:4 (1 Sqm 2037.78

cement : 4 coarse sand) in all shapes & patterns including grouting the

joints with white cement mixed with matching pigments etc. complete

as per direction of Engineer-in-Charge.

Providing and supplying D. I. K-9 grade pipes (total length 5 meter) for

following nominal bore diameter with internal cement mortar lining

322 50.00 including all taxes, insurance, transportation, freight charges, octroi, RMT 2920.92

inspection charges, loading, unloading, conveyance,etc. is considered

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Manufacture, Supply & Delivery of Ductile Iron Flange socket spigot

bends, tees, reducers or any other specials as per BS-EN-545/1995 Class-A

323 100.00 series K12 suitable for use with D.I. Pipes manufactured as per KG 149.48

IS:8329/1994 including all taxes, leading, unloading, carting, stacking,

insurance, inspection charges, octroi etc. complete 250 DIA LINE

Providing and supplying ISI mark CI D/F Sluice Valves , Butterfly Valves

& Reflux Valves of following class and diameter including all taxes,

324 1.00 insurance, transportation, freight charges, octroi, inspection charges, EACH 8648.63

loading, unloading, conveyance, stacking etc. complete.(PN1-with hand

wheel operated-short) 250 mm Dia

325 100.00 M.S. SPECIALS Plain and Socket Ends KG 96.96

Electromagnetic Flow Meters as per dia MS GSM/ GPRS /PC /SCADA

Systems Internal data logging function (Approx. 15,000 reading)

Excavation for foundation including sorting out and stacking of useful

327 30.00 materials and disposing off the excavated stuff up to 50 Meter lead. Loose / CUM 89.89

hard soil. up to 1.50 mt depth

Filling available excavated Earth (Excluding Rock) in trench plinth side of

328 25.50 foundation etc. in layer not exceeding 20 cm in depth consolidation each CUM 143.43

deposited layer by ramming and watering etc. complete.

Providing And Making Flanged Joint of Flanged DI/CI Pipe Classes

Specials etc.. Including Cost of All Jointing Materials Rubber Packing, Nut

Bolts, Including Lowering Laying Jointing Labour Hydraulic Testing etc

330 1.00 Fixing of Sluice Valves 200 mm dia No. 955.46

Constructing masonry Chamber 90x90x100 cm inside, in brick work in

cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I.

surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm

deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement :

2coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c No.

necessary excavation,foundation concrete 1:5:10 (1 cement : 5 fine sand:

10 graded stone aggregate 40 mm nominal size ) and inside plastering with

cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a

floating coat of neat cement complete as per standard design : 18.34.1 With

common burnt clay F.P.S.(non modular) bricks of class designation

Excavation for foundation up to 1.5 mt deepth including sorting out

stracking of useful materials and disposing the Exavatated stuff within plot.

Lead. Rate includes back filling of earth. Loose /soft or hard soil

Providing & Laying (To level or slopes)

& jointing reinforced concrete light duty non pressure pipes IS class NP3 of

333 246.71 the following internal diameter with collars and butt ends prepared for RMT 762.55

collar joints including testing of joints complete. RCC300 dia pipe

Lowering laying and jointning RCC pipe in 1:1 1/2 in proper position

334 246.71 grade and alignment and as directed by EIC including convayence labour RMT 120.19

and testing as per ISI code.

Making connection to the existing manhole in running sewer following dia.

pipes, at convenient time when manhole is found empty. All damage shall

be repaired as per instruction of engineer in charge. etc. complete. Dr.

connection up to 300 mm

Constructing manhole with RCC (top slab in 1:2:4 mix (cement : 2 coarse

sand : 4 graded stone aggregate 20mm nominal size) foundation concrete

1:3:6 mix ( 1 Cement : 3 coarse sand : 6 brickbats 40:50mm size) in side

plastering 15mm thick with cement mortar 1:5 (1 cement : 5 coarse sand)

336 6.00 finished with a floating cost of neat cement and making channels in cement cum 12300.79

concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20mm

nominal size) finished smooth complete incl curing & testing (1) inside size

900 x 1200mm incl. F R C medium duty cover and frame

A type depth 1.0 meter UPTO 1.5 METER DEPTH

337 2.00 B type depth 1.50 meter UPTO 3.0 METER DEPTH cum 21327.16

Excavation for foundation including sorting out and stacking the excavated

338 15.05 stuff up to 50mt lead for A) Loose or soft soil CMT 120.01

Upto 1.50 mt. depth

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Boring holes 3.5 m deep in ordinary soil (for cast in situ piles) and getting

339 74.31 out the soil and disposal of the surplus excavated soil as directed within a EACH 1561.19

lead of 50 Meter for following diameter of pipes.(iii) 300 medial mensicus

Proving Borewell witch all accessories isi approved materials bore 6 inch

340 1.00 and as per site condition water level required depth All materials bore wich Nos 111100.00

submersible pum set use as per tender details our engineer in charge

Providing and laying cement concrete 1:4:8 (1- Cement : 4- coarse sand : 8-

341 8.92 hand broken stone aggregates 40 mm nominal size) and curing complete CMT 2747.30

excluding cost of formwork in (A) Foundation and Plinth (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing

complete excluding the cost of formwork and reinforcement for reinforced

concrete work in (A) Foundations, footings, Base of columns and Mass

concrete. (more than 10 ton)

Providing TMT Bar FE 500D reinforcement for R.C.C. work including

343 3495.77 bending, binding and placing in position complete upto floor two level KG 77.29

(more than 10 ton)

Providing formwork of ordinary timber planking so as to give a rough

finish including centering shuttering strutting and propping etc. Height of

344 200.64 propping and centering below supporting floor to ceiling not exceeding 4 SMT 179.36

M. and removal of the same for in situ reinforced concrete and plain

concrete work in. (A) Foundations Footings Bases of Columns etc. and

(G) Columns PillarsPosts and struts. (1) Square Rectangular Polygonal in

plan. (upto 10 ton)

(H) (1) Sides and soffits of Beams Beam Haunchings cantilevers Girders

Bressumers and Lintels not exceeding 1 M. in Depth. (upto 10 ton)

Brick work using common burnt clay building bricks having crushing

347 92.29 strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement CMT 4391.22

Mortar 1:6 (1- Cement : 6 -fine sand)(A) Modular

20mm thick sand faced cement plaster on walls upto height 10 metres

above ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-

cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-

sand) etc. complete.

Finishing wall with weather proof exterior emulsion paint on wall surface

(two coats) to give an required shape even shade after thoroughly brushing

the surface to remove all dirt, and remains of loose powdered materials.etc

Providing and fixing M.S. grills of required pattern to with M.S. flats at

350 360.00 required spacings and frame alround, square or round bars with round KG 105.18

headed bolts and nuts or by screws (A) Plain Grill. (upto 10 ton)

Painting two coats (excluding priming coat) on new steel and other metal

surface with enamel paint, brushing, interior to give an even shade

including cleaning the surface an even shade including cleanicn the surface

of all dirt, dust and other foreign matter.

Box cutting the road surface to proper slope and camber for making a base

352 475.79 for road work including removing the excavated stuff and depositing on the Cum 104.20

road side slope as directed upto 50Mt.lead.

Earthwork for embankment including breaking clods, dressing with all lead

353 158.23 and lift (excluding watering and consolidation)(E) From Borrow area Cum 230.31

within 3.0 Km. lead (more than 10 ton)

Rolling of earthwork in layers with power roller including filling in

depressions which occur during the process. (more than 10 ton)

355 158.23 Watering of earth work as directed. Cum 9.08

Providing and laying cement concrete 1:3:6 (1-Cement : 3- coarse sand : 6-

hand broken stone aggregates 40 mmnominal size) and curing complete

excluding cost of formwork in (A) Foundation and Plinth (more than 10 ton)

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Providing and laying in position Ready Mixed M-250 grade concrete for

reinforced cement conctere work , using cement content as per approved

Design Mix manufactured in fully automatic batching plant and transported

to site of work in transit mixer for a lead up to 10 kms having continuous

agitated mixer, manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of R.M.C. from transit

357 237.35 mixer to site of laying, excluding the cost of centering shuttering finishing Cum 4776.90

and reinforcement including cost of admixtures in recommended

proportions as per IS: 9103 to accelerate/ retard setting of concrete,

improve workability without impairing strength and durability as per

direction of the Engineer - in - charge. Without Fly Ash (Min cement level

as per latest IS 456 shall be maintained) (Cement level 450 kg )

Providing TMT Bar FE 500D reinforcement for R.C.C. work including

358 7120.44 bending, binding and placing in position complete upto floor two level Kg 77.18

Finishing of C.C.Road by provinding labour charges by using vaccum

dewatering pump floater surface vibrator including making grooves Rufe

finish to surface levelling up etc. comp As Per engineer in charge.

Excavation for foundation including sorting out and stacking the excavated

360 263.68 stuff up to 50mt lead for A) Loose or soft soil Cum 120.01

Upto 1.50 mt. depth

Providing and laying cement concrete 1:4:8 (1- Cement : 4- coarse sand : 8-

hand broken stone aggregates 40 mm nominal size) and curing complete

excluding cost of formwork in (A) Foundation and Plinth (upto 10 ton)

Providing and fixing pre-cast Rubber Dye inter locking concrete block

80mm thick with grade of concrete M450 pnumatic compressed by

362 1014.15 mechanically pressed and as per approved design including 75mm Sand SMT 909.00

layer for levelling and filling the joint with sand in proper line and level etc

Providing and fixing pre-cast concrete kerb stone of gray cement based

concrete block 30cm length,30cm height and 15cm thick of M250 grade

363 78.41 concret as per approved design and including excavation for fixing in RMT 370.68

proper line and level,filling the joint with C:M 1:3 (1cement:3fine sand) etc

Excavation for foundation up to 1.5 mt deepth including sorting out

364 324.71 stracking of useful materials and disposing the Exavatated stuff within plot. CMT 120.01

Lead. Rate includes back filling of earth. Loose /soft or hard soil

Providing & Laying (To level or slopes)

& jointing reinforced concrete light duty non pressure pipes IS class NP2 of

the following internal diameter with collars and butt ends prepared for

collar joints including testing of joints complete. 250 mm dia

Lowering laying and jointning RCC pipe in 1:1 1/2 in proper position

366 197.88 grade and alignment and as directed by EIC including convayence labour RMT 116.15

and testing as per ISI code. 250 mm dia

Construction of B.P. type catch pit of the size 0.60x0.60 mt depth upto

mt incl. Excavation BBCC 1:5:10 , 23 cms brick wall in C:M 1:6 , 40 mm

thick IPS in flooring in proportion M15 at bottom and 20mm thick cement

plaster in side the catch pit in C:M 1:3 with jali etc. comp. as directed.

Including P/F FRC catchpit jali with frame 600mm x 600mm clear opening

etc. comp.. As directed by engineer in charge.

Providing and fixing ANGLE FOR set of 3PVC Dust bin of 0.3 cum

capacity to be hanged and fixed in 50X50X5 mm angle frame, moving on

axis as per design given for primary storage of garbage from park, open

spaces and households etc. All complete as directed by EIC.

Providing and fixing set of 3PVC Dust bin of 0.3 cum capacity to be

hanged and fixed in angle frame, moving on axis as per design given for

primary storage of garbage from park, open spaces and households etc. All

complete as directed by EIC.

Ploughing and leveling the plot area / ground area and watering the same

ground including clearing and removal of stones, wood, aggregates,

rubbish, uprooting vegetation, grass complete with surface dressing of the

ground as directed

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Providing, laying and developing approved quality of grass turfing on

common plot area including cost of grass, manure / fertilizer, sweet soil,

371 180.00 protection and labour charges inclusive of stacking, mixing & spreading of Sqm 121.20

earth, manure, sludge etc., watering, forking the ground complete as

Providing & Planting trees (like Mango, Limbado, Gulmohar etc.) along

with Providing and fixing Ornamental Tree Guard with MS Bare

manufactured as per design and drawing . The rate shall include cost for

372 20.00 labour and materials involved in all operations including holdfasts, fixtures Sqm 181.80

and fasteners, welding. The entire tree-guard shall be given two coats of

paint of approved brand and of required shade over a priming coat of ready

mixed primer etc. complete as directed

Supplying and Planting Colorful flowers plants including cost of all plant

material, sowing and transportation of all seeds, labour charges incl. of fine

373 20.00 dressing of earth, anure, sludge etc watering etc. complete as Sqm 121.20

irectedstacking, mixing & spreading of earth, manure, sludge etc watering

etc. complete as directed

Filling in plinth with sand under floors including watering ramming,

consolidating and dressing complete (upto 10 ton)

Providing and fixing Graden Play Equipments Installtion Swings, Slides,

375 6.00 Seesaws, Marry-go- round Etc.. AS per tender or Engineer in charge NOS 12120.00

Drilling of bore hole in Alluvial Strata by Direct Rotary rig. '(i) 250 /

mm dia bore hole

Providing and supplying ISI mark M.S. E.R.W. pipes with 'following

diameter confirming to IS : 4270 - 1992 including all taxes, insurance,

transportation, freight charges, octroi, inspection charges, loading,

377 36.80 unloading, conveyance to departmental stores, stacking etc. complete. Rmt 2431.07

Medium Duty Plain Ended

Providing and supplying following materials for borewell Clamps made

from M.S. plate with 3 holes on either side with nuts & bots of standard

make and suitable size.

(g) 900 mm X100 mm X 16 mm flat suitable to 200 mm dia. Pipe.

Bore plug having 100 mm height made from M.S. plate with 3 holes at

equal distance on circumference for nut-bolts type, locking arrangement

379 1.00 with nuts-bolts & lock nuts of standard make etc. complete. NO 782.57

[b] From 5 mm thick M.S. plate ( For Top also )

'ii) Suitable for 200 mm dia pipe

M.S. Bail plug having length 0.45 mtr. from medium class pipe as per I.S.S

380 1.00 suitable for NO 851.04

'd) 200 mm dia pipe

Lowering of E.R.W. pipes, pipes shall be lowered in such a manner as not

to damage either the pipes or mud wall of the bore. If pipes are dropped or

381 36.80 mud wall damage, causing heaving of sand, cost of bore shall be recovered Rmt 418.14

from the contractor.

Cement grout seal The grout shall be 1:1. The largest size aggregate

allowed is 10 mm pebbles. The grout will have to 'be in placed in such a

382 1.00 way that the cement sand and aggregate will not be separated due to water. L.S. 13405.73

Any method of doing so will have to be approved by the

architects/Engineer.

383 1.00 Bottom sealing of bore hole as per standard procedure. L.S. 6727.61

Gravel packing:Gravel packing shall be done slowly and sounding of gravel

will have to be taken, after putting in every layer.

Lowering and removing of 100 mm dia dropline and 32 mm dia airline

for development of each water bearing zones 'come across upto full depth

of deep tubewell of size 200mm / 250 mm / 300 mm dia for tubewell

385 1.00 having depth 151 mtr. and above through suitable air compressor. The job Job 22427.05

is for complete period of development of tubewell.

'( Without charges for air compressor.)

Charges for suppying, hiring Air compressor including all associated

386 12.00 necessary expenditure. HR. 2746.19

'1) 400 CFM / 100 PSI compressor

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Welding in all positions with required number runs, for M.S /E.R.W. pipes

internally including gauging wherever 'necessary, fixing appurtances and

387 20.00 other accessories in connection with pipe laying work as per specification Rmt 656.50

'Butt Joints : Plate thickness

Excavation for foundation up to 1.5 m depth including sorting out and

stacking of useful materials and disposing of the excavated stuff up to

388 8.00 meter lead. Cumt 120.01

(A) Loose or soft soil Mtr. lead

Excavation for foundation for depth from 1.5 m to 3.0 m depth including

sorting out and stacking or useful materials and disposing of the excavated

389 6.00 stuff upto 50 M lead. Cumt 133.05

(A) Loose or soft soil

Providing and laying cement concrete 1:4:8 (1- Cement : 4- coarse sand : 8-

hand broken stone aggregates 40 mm nominal size) and curing complete

excluding cost of formwork in (A) Foundation and Plinth (upto 10 ton)

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:6 (1- Cement : 6 -fine sand)(A) Modular (upto 10 ton)

Providing and fixing factory made precast RCC perforated drain

covers, having concrete of strength not less than M-25, of size 1000 x

450x50 mm, reinforced with 8 mm dia four no longitudinal & 9 nos cross

392 1.00 sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ No 1060.50

100 to 125 mm c/c, including providing edge binding with M.S. flats of

size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge.

Providing TMT FE - 500D bar reinforcement for R.C.C. work including

393 22.50 bending binding and placing in position Complete. Up to Floor Two Level. Kg 77.29

Supplying & filling FINE sand in Filter Beds for preparation of filter

bed upto average 5.0 mt depth below surrounding average ground level

including cost of sand, transportation for all leads,loading unloading,

spereading in layers as specified below. Loose thickness at all depths

dressing and levelling dewatering sub soil or rain water if any etc. complete.

394 2.00 [ The uniformity coefficient of sand Cumt 505.00

shell be 1.2 to 1.8 ]

a. Fine sand of size 0.35 to 0.55 mm in

a layer of 1000 mm thick

Supplying & filling GRAVEL in Filter Bed for preparation of filter bed

upto average 7.0 mt depth below surrounding average ground level

including cost of gravel transportation for all leads, loading, unloading,

spereading in layers as specified below. Loose thickness

395 2.60 at all depths dressing and leveling dewatering sub soil or rain water if any Cumt 1515.00

a. Gravel of size 3 to 6 mm in

a layer of 150 mm thick

396 1.00 b. Gravel of size 6 to 20 mm in a layer of 200 mm thick Cumt 1464.50

397 1.00 c. Gravel of size 20 to 40 mm in a layer of 200 mm thick Cumt 1313.00

398 1.00 d. Gravel of size 40 to 60 mm in a layer of 250 mm thick Cumt 1212.00

Supplying & filling BOULDERS around central water trough in a layer of

200 mm thick. in Filter Bed .

Filling available excavated earth (excluding rock) in trenches, plinth, sides

400 9.00 of foundations etc. in layers not exceeding 20cm. in depth consolidating Cumt 130.39

each deposited layer by ramming and watering.

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm &

earth wire of 1.5 sq.mm (green) both are of .ISI marked 1.1 KV grade

FRLS PVC insulated multi strand copper wires erected in below type of

pipe with 6A Modular type switches and following type of accessories

401 325.00 erected on PVC / Metallic/Wooden box, single mounting base frame pt 603.98

covered with textured / metallic/white front plate modules erected on / in

wall / ceiling as per pipe erected. with necessary batten/angle holder or

ceiling rose or H.D.Connector as directed

(f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete - CAT III

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length , in below type of pipe

erected with 6A Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC / Metallic/Wooden box,

single mounting base frame covered with textured/metallic/white front

plate modules erected on / in wall / ceiling as per pipe erected, with

necessary Lamp holder/ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete - CAT III

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green)

both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type of pipe erected with 6A

Modular type switch and hum free EME step type electronic fan regulator

mounted and accessories with earth continuity of following type erected on

PVC / Metallic/Wooden box, single mounting base frame covered with

textured/metallic/white front plate modules erected on / in wall / ceiling as

per pipe erected. with necessary ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete - CAT III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green)

both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type of pipe erected complete

with Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden

404 675.00 box covered with appropriate front plate modules erected on / in wall / pt 510.05

ceiling as per pipe erected with following type of accessories.

[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby

switchboard/mcb db board (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete Cat. III

[II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu. Wire from

405 485.00 mcb db board.(f) with medium class Rigid PVC pipe and accessories pt 745.38

erected concealed in wall/ceiling complete Cat. III

Point wiring for on board Looped Plug with 6A Modular type switch &

pin socket erected on PVC / Metallic/Wooden box, single mounting base

frame covered with textured / metallic/white front plate modules erected

on / in wall / ceiling with following type accessories catt-iii

Providing following type of Modular Type Accessories mounted with PVC

/ metallic/Wooden box, single mounting base frame covered with textured /

407 110.00 metallic/white front plate , modules erected with necessary connections as EACH 160.59

per site situation directed by Engineer In charge. CAT - III

(3) Two Pin/RJ-11 Telephone Socket

Providing following type of Modular Type Accessories mounted with PVC

/ metallic/Wooden box, single mounting base frame covered with textured /

408 115.00 metallic/white front plate , modules erected with necessary connections as EACH 160.59

per site situation directed by Engineer In charge. CAT - III

(4) TV Co-axial Socket outlet

Providing following type of Modular Type Accessories mounted with PVC

/ metallic/Wooden box, single mounting base frame covered with textured /

409 1000.00 metallic/white front plate , modules erected with necessary connections as EACH 25.25

per site situation directed by Engineer In charge. CAT - III

(7) Blank Plate Single

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Providing following type of Modular Type Accessories mounted with PVC

/ metallic/Wooden box, single mounting base frame covered with textured /

410 275.00 metallic/white front plate , modules erected with necessary connections as EACH 160.59

per site situation directed by Engineer In charge. CAT - III

(8) Computer RJ-45 socket

Providing following type of Modular Type Accessories mounted with PVC

/ metallic/Wooden box, single mounting base frame covered with textured /

411 65.00 metallic/white front plate , modules erected with necessary connections as EACH 151.50

per site situation directed by Engineer In charge. CAT - III

(11) 6 Amps. Bell Push

Providing following type of Modular Type Accessories mounted with PVC

/ metallic/Wooden box, single mounting base frame covered with textured /

412 50.00 metallic/white front plate , modules erected with necessary connections as EACH 149.48

per site situation directed by Engineer In charge. CAT - III

(20) Modular Buzzer

Providing following type of Modular Type Accessories mounted with PVC

/ metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate , modules erected with necessary connections as

per site situation directed by Engineer In charge. CAT - III

(24) Batten Holder/Angle Holder with modular frame with metal ring.

Providing and erecting ISI mark Medium class RIGID PVC PIPES of

following size complete to be erected on/in wall or ceiling erected with

414 2150.00 necessary PVC fittings & Junction boxes fixed with adhesive solution & mtr 33.33

Clamps with following dia of pipes, in approved manner as directed (b)

Providing and erecting ISI mark Medium class RIGID PVC PIPES of

following size complete to be erected on/in wall or ceiling erected with

415 865.00 necessary PVC fittings & Junction boxes fixed with adhesive solution & mtr 67.67

Clamps with following dia of pipes, in approved manner as directed (b)

Providing & erecting PVC Corrugated Flexible Conduit with required nos.

416 1230.00 of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (2) mtr. 21.21

Supplying under floor pregalvanised corrosion proof rectangular sheet

steel cable trunking of 1.6 mm thick having with stand point load up to

1.33 Ton & free from seepage of concrete of screed water with all

417 250.00 accessories,Junction Box,Joints as required and demanded by engineer- mtr. 1342.29

incharge and laying/erecting as per OEM guidelines and as per instruction

of engineer incharge having following size of dimensions and No of

compartments (W x D x T) Cat-III

[13] 300mm x 38mm x 1.6 mm with Three Compartments

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper

418 1430.00 conductor FRLS PVC insulated stranded wire of green colour for earth mtr 62.62

continuity of following size (A) With medium class Rigid PVC pipe and

(a) 2 wire 1.5 sq. mm

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity of following

size (A) with medium class Rigid PVC pipe and accessories .

(d) 3 wire 4 sq. mm

Supplying and erecting Flexible PVC insulated multi strand multi core

kv grade ISI marked copper wires of following size to be erected as

(e) 1.50 Sq.mm 3 core round PVC sheathed

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

providing and erecting Mains with ISI marked, 1.5KV grade electrolyte

multi stranded, annealed copper conductor with heat resistant PVC

insulated conforms to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays, power switchgears,

motor starters & control wiring) with required size of copper lugs, nuts and

bolts if required. (d) One wire 4.00 sq. mm

426 150.00 (e) One wire 6.00 sq. mm Mtr. 56.56

427 100.00 (f) One wire 10.00 sq. mm Mtr. 91.91

428 200.00 (g) One wire 16.00 sq. mm Mtr. 142.41

Providing & Erecting approved make following size of TV Co-axial

flexible cable comprising inner conductor of solid bare copper insulated

429 1500.00 with Foam PE & Secondary conductor made of poly - Aluminium film each 39.39

bonded Al. Braids @ suitable coverage overall sheathed with black PVC

Supplying & erecting approved make LAN cable of following size in

430 2440.00 existing pipe as per direction each 47.47

Providing & erecting Switch board for Computer or electric apparatus

consisting of following modular type accessories mounted with PVC /

Metallic concealed/open box with single mounting base frame covered with

textured/metallic /white front plate,modules erected with necessary

431 65.00 connections as directed each 1133.22

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug

For Modular Type Accessories CAT III

Supplying & erecting Approved make call bell indicator with buzzing

432 15.00 sound and Red light indicating lamp with Red light button to attend the call each 148.47

suitable for 240 v 50 c/s supply to be erected.

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt

to 0.5 Watt assembled on single MCPCB, with housing used as a heat sink

shall be made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium

die cast powder coated and high U.V. & corrosion resistance with diffuser

with company mark/name 160V to 270V, Power Factor more than 0.95,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the ranges shown.)

(A) Tube Light with integral driver

(iii) 18-20 Watts, Surge - 2KV,IP-20, conventional 4 feet - CAT III

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt

to 0.5 Watt assembled on single MCPCB, with housing used as a heat sink

shall be made of thick sheet Steel conforming to IS: 513/CRCA/aluminium

pressure die cast powder coated and high U.V. & corrosion resistance

with diffuser housed in aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

434 1350.00 Luminaire efficacy> 85 lumens/watt , each 758.51

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with

provision for spring loaded mounting clips complete.IP20

(iv) 22-24 watts, Surge-2 KV

435 285.00 (ii) 11-15 watts, Surge-2 KV each 427.23

(B) LED Panel Light with provision for Plane front frame with translucent

436 15.00 cover fixed to housing complete.IP20 each 1794.77

(vi) 36 watts, 24" x 24", Surge- 2KV - CAT III

437 145.00 (H) Mirror Light 9 Watts, wall mounted minimum 1 feet long each 312.09

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

LED Bollard fittings of minimum height 600 mm & dia.100mm having

polycarbonate clear/milky diffuser mounted on 3mm thick aluminium

438 20.00 finished powder coated pipe with base plate 160x160mm with erection by each 3161.30

M8x75mm fastner with required RCC foundation.IP65 for 9 to 20 watt

,surge-4kv- cat-III

Supplying and erecting LED street light / Flood light fittings with High

power White LEDs wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and corrosion free High pressure

die cast aluminum housing with smooth finish powder coated and heat sink

extruded aluminium with diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name engraved or embossed 160 to

270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt .

LED driver efficiency > 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) (A) Street Light (IP-65), Surge

protection -4KV integral and ,Light must have 440VAC line supply with

over-voltage protection. (ii) above 48 to 60 Watts CAT-III

Supplying and Erecting Of L.E.D. type High bay fixture having Power

Consumption of following watts with, Input Voltage 110 - 290 V.AC with

full efficiency, Power Factor > 0.9 with 50/60 HZ, CCVC LED Driver used

440 40.00 for maximum power saving, Best Quality Aluminium alloy housing and each 10271.70

aluminium Dome for better heat dissipation, CCT Cool white (6000K), CRI

80, Beam angle > 120 degrees, working temperature -20 deg c to +55 deg

(C) 150 to 200 watts

Providing Approved make Triple Pole metal clad switch fuse unit 415 /

441 2.00 500V. 400 A with HRC fuse of suitable load and neutral link confirming to each 13353.21

Providing and erecting Approved make panel mounting front fixing rotary

switch (CAM Switch) with face plate with double pair of contacts with two

442 2.00 fix and a moving contacts, operated by means of slide, rest on disk with each 729.22

grooves for sequential operation rotated by switch handle, square shaft and

knob for Two way with off Cat III

(ii) Four pole - (b) 32A- 440V

Supplying & erecting following spare parts for panel mounting Switch

Disconnector Fuse Units Operational Handle Assembly Complete for

Supplying & erecting following spare parts for panel mounting Switch

444 4.00 Disconnector Fuse Units Operational Handle Assembly Complete for each 754.47

Supplying & erecting following spare parts for panel mounting Switch

Disconnector Fuse Units

Operating Shaft (Extensible) for

Supplying & erecting following spare parts for panel mounting Switch

Disconnector Fuse Units

Operating Shaft (Extensible) for

Supplying & erecting following spare parts for panel mounting Switch

Disconnector Fuse Units

Cable Terminal ( ‘Z" Type) Set of Two for

Supplying & erecting following spare parts for panel mounting Switch

Disconnector Fuse Units

Cable Terminal ( ‘Z" Type) Set of Two for

(iii) 630 / 800 Amps

Supplying & erecting following spare parts for panel mounting Switch

Disconnector Fuse Units

Cable Terminal ( ‘Plain" Type)Set of Four for

(i) 32 / 63 Amps

Supplying & erecting following spare parts for panel mounting Switch

Disconnector Fuse Units

Cable Terminal ( ‘Plain" Type)Set of Four for

(ii) 125 / 200 Amps

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Supplying & erecting following spare parts for panel mounting Switch

Disconnector Fuse Units

Cable Terminal ( ‘Plain" Type)Set of Four for

(iii) 250 / 320 Amps

Supplying & erecting following spare parts for panel mounting Switch

Disconnector Fuse Units

Cable Terminal ( ‘Plain" Type)Set of Four for

Pproviding and erecting Approved make Four pole moulded case circuit

breaker having breaking capacity ICU of 25 KA. at 415 V,having normal

current rating up to 25 A to 100A. with Fixed thermal & magnetic release

suitable to work on A.C. supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III

Providing and erecting Approved make Four pole moulded case circuit

breaker having breaking capacity ICU of 35 KA. at 415 V. having Normal

454 3.00 current rating 200A.with variable Thermal & magnetic release suitable to each 16221.61

work on A.C.supply 50 c/s. with all internal connections, spreader tinned

copper & complete erected in existing 16 G.M.S.housing. ICS=100% of

ICU only Cat III

Providing and erecting Approved make Four pole moulded case circuit

breaker having breaking capacity ICU of 35 KA. and above at 415 V .

455 2.00 having normal current rating 250A. with variable thermal & magnetic each 20946.39

release suitable to work on A.C.supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III

Providing and erecting Approved make Four pole moulded case circuit

breaker having breaking capacity ICU of 50 K.A. and above at 415 V

having normal current rating up to 630A. with variable thermal & magnetic

release suitable to work on A.C.supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in existing 16 G.M.S. housing

ICS=100% of ICU only Cat III

Providing and erecting Approved make Earth fault Relay suitable to mount

with inter connection suitable to following size of moulded case circuit

457 3.00 breaker having CT ratio & MCCB rating as following along with shunt trip each 4983.34

220V AC. with all internal connections & complete erected in existing

Providing and erecting Approved make Earth fault Relay suitable to mount

with inter connection suitable to following size of moulded case circuit

458 3.00 breaker having CT ratio & MCCB rating as following along with shunt trip each 5415.62

220V AC. with all internal connections & complete erected in existing

Providing and erecting Approved make Earth fault Relay suitable to mount

with inter connection suitable to following size of moulded case circuit

459 3.00 breaker having CT ratio & MCCB rating as following along with shunt trip each 6056.97

220V AC. with all internal connections & complete erected in existing

Providing and erecting following additional parts for panel mounting

(A)Extended operating rotary handle with pad lock with three position

trip,off,on suitable for 25A to 250 A panel mounting cat-III

Providing and erecting following additional parts for panel mounting

(B)Extended operating rotary handle with pad lock with three position

trip,off,on suitable for 400A to 630 A panel mounting cat-III

Supplying & erecting approved make Four Pole 415V change over switch

interior for panel mounting with operating mechanism A.C.23 duty

confirming to IS for

(E)250A / 320A cat-III

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Supplying and erecting triple pole & neutral 440V/ 500V panel mounting

Aluminium Busbars with four equal Nos. of bus having current density not

more than 0.8 Amp. / sq.mm (Rated current / cross section area) duly

463 10.00 wrapped with colour insulating tape for phase sequence of following Rn. Mtr. 2204.83

current carrying capacity, erected with necessary bus bar supports

/insulators, main cable socket to each busbar,erected in existing cubical

panel with necessary connections.

(D) Suitable for 400 Amp. Capacity

Supplying and erecting triple pole & neutral 440V/ 500V panel mounting

Aluminium Busbars with four equal Nos. of bus having current density not

more than 0.8 Amp. / sq.mm (Rated current / cross section area) duly

464 5.00 wrapped with colour insulating tape for phase sequence of following Rn. Mtr. 3061.31

current carrying capacity, erected with necessary bus bar supports

/insulators, main cable socket to each busbar,erected in existing cubical

panel with necessary connections.

(E) Suitable for 630 Amp. capacity

providing and erecting Miniature circuit breaker single pole 0.5A to 2A

465 55.00 system and having breaking capacity 10 KA to be erected in existing box. nos 270.68

confirming to IS 8828/1996 with ISI Mark Cat.III

providing and erecting Miniature circuit breaker single pole 6A to 25A

suitable to operate on 240 V A.C. system and having breaking capacity

KA to be erected in existing box. confirming to IS 8828/1996 with ISI

Providing & erecting 240 V MCB double pole switch for motor &

inductive load (C Curve) having 10 KA breaking capacity & confirms to

IS : 8828 in existing box having following capacity Cat.III

(A) 6 to 32 Amp.

Providing & erecting 240 V MCB double pole switch for motor &

inductive load (C Curve) having 10 KA breaking capacity & confirms to

IS : 8828 in existing box having following capacity Cat.III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load

(C Curve) having 10KA breaking capacity & confirms to IS :8828 in

existing box having following capacity Cat.III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load

(C Curve) having 10KA breaking capacity & confirms to IS :8828 in

existing box having following capacity Cat.III

Providing & erecting 415 V MCB three Pole for Motor & Inductive Load

(C Curve) having 10KA breaking capacity & confirms to IS :8828 in

existing box having following Cat.III

Supplying & erecting 20 Amp 10 KA ‘C Curve’ single pole MCB with

20 Amp. Plug socket, company fabricated powder coated sheet steel

enclosure erected as directed with connection. CAT- III

[B] 15 Amp. / 5 Amp. Five pin Universal Socket

473 200.00 Half / One Module Blanking Plate of Standard Size. each 9.09

Plastic enclosure fitted with DIN rail suitable for incorporating One / Two

Plastic enclosure fitted with DIN rail suitable for incorporating Three

Sheets steel powder coated enclosure suitable for incorporating One/Two

Providing and erecting Sheet Steel powder coated MCB distribution board -

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

477 55.00 appropriate nos. of MCBs.(The DBs should be used of same company of each 1680.64

MCB to be used) suitable for

(A) single phase incoming and horizontal single phase outgoing

(b) sheet steel double door (IP-43)

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Providing and erecting Sheet Steel powder coated MCB distribution board -

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of same company of

478 40.00 MCB to be used) suitable for each 3874.36

(B) three phase incoming and single phase horizontal type outgoing Per

phase isolation type (PPI)

(b) sheet steel double door (IP-43)

Providing & erecting approved make thermo plastic MCB/RCCB

distribution board having modular Double door with DIN rails, epoxy

479 20.00 powder coated finish metal frame & door assembly with Acrylic/ Plastic each 2346.23

door, spring & hinged pins complete with required PVC sleeved 32 / 63A

copper Bus strips without MCB / RCCBs

(e) Two Row 28 Module

Providing and erecting powder coated distribution board with WI-FI -

flush / surface mounted double door (IP-42) fitted with size

480 4.00 475*398,CRCA sheet thickness 0.9mm,Genral Tolerance,Power Coting each 4201.60

DFT 60-90 micron,Frame Thickness 1.2mm.,Frame & Cover Material

Metal with Nessesary Accessories

providing and erecting Approved make RCCBs conforming to IS:

and having sensitivity of 30 mA and Short Circuit withstand capacity of

KA and suitable for operation on single phase 240 V,50Hz. having

481 45.00 characteristic of quick action & tripping with all advance feature & do not each 1969.50

incorporate any electronic component. for following Max. rating erected as

directed CAT-III

providing and erecting Approved make RCCBs conforming to IS:

and having sensitivity of 30 mA and Short Circuit withstand capacity of

KA and suitable for operation on single phase 240 V,50Hz. having

482 65.00 characteristic of quick action & tripping with all advance feature & do not each 2235.13

incorporate any electronic component. for following Max. rating erected as

directed CAT-III

(ii) 40Amps. DP

Providing and erecting Approved make RCCBs conforming to IS:

and having sensitivity of 30 mA and Short Circuit withstand capacity of

KA and suitable for operation on 3 phase and neutral 415V,50Hz. having

483 10.00 characteristic of quick action & tripping with all advance feature & do not each 3040.10

incorporate any electronic component for following Max. rating erected as

directed. CAT-III

(iii) 63 Amps. FP

Supplying & erecting approved make RCCB + MCB (Electro magnetic

type only) working on residual current device having 10 KA short circuit

breaking capacity and 30 mAmp. Sensitivity & 30 mili sec. tripping time

484 35.00 conforming to IS 12640 test knob facility trip free mechanism operating for each 1944.25

rated leakage at nominal ten volt, complete erected including all materials

lugs screws etc. completed.

[b] 32A / 40A, 2 pole Single Phase

Providing and erecting metallic vitrified danger notice board as per

485 40.00 language suggested by engineer incharge for MEDIUM VOLTAGE each 69.69

installation to be erected as per IS-2551.

Providing and erecting metallic vitrified danger notice board as per

486 40.00 language suggested by engineer incharge for HIGH VOLTAGE installation each 81.81

to be erected as per IS.-2551.

Providing and erecting required size HOT deep Galvanised iron strip for

487 125.00 earthing of H.T. , OCB/ ACB/ Transformer LT panel board, Motors etc. kg 77.77

using proper clamp.

Providing and erecting required size Copper strip for earthing of H.T. OCB

/ ACB/ Transformer, LT panel board, Motors etc. using copper clamp.

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Supplying & erecting in earthpit of minimum bore dia. 225mm size

approved make Safe Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped

G.I.Pipes having Outer pipe dia of 80 mm having 80-200 Micron

galvanising, Inner pipe dia of 40 mm having 200-250 Micron galvanising,

connection terminal dia of 14 mm with constant ohmic value surrounded

by highly conductive compound with high charge dissipation suitable for

following type of applications with chamber and heavy duty cover

(A)(approved make OEM has to submit test certificate including value of

489 12.00 earth resistance of installation duly stamped and signed by agency and each 10593.89

officer Incharge has to ensure the value of earthing resistane mentioned in

test Certificate) & having back filling compound of (B) Inner chemical

(CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-

2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:-

<2%(C) Back fill Compound :- Earthing compound should be capable to

retain moisture for long time Necessary test report must be submitted by

[C] For Electrical Installation covering Transformer Neutrals, Lightning

arrester Earthing, A.C.Plant & Sensitive Computer System(like

Providing one bag of 25 Kg. Additional Back Filling Compound (BFC)

suitable for safe earthing device.

providng and erecting Approved make. energy meter 3 phase 4 wire

491 5.00 unbalanced load 500 V.50A / 100A complete erected as directed with each 2611.86

necessary earth wire. CAT- III

Providing & erecting weather proof, dust & vermin proof, floor mounted

front operated outdoor type double door cubical panel board necessary IP-

54 and above protection as per approval from engineer incharge made from

14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC

M.S.sheet for internal partitions with necessary accesories , supporting

angles/ flats channel including cutting, bending, drilling, welding, riveting

with internal partitions & cable alley as per requirements & instruction of

engineer-in-charge with erection of

supplied switch gears, BUSBARS, suitable size of inter connecting PVC

copper wire / copper-aluminium strips, rubber grommets, rib, bakelite

control fuses/MCB for measuring instruments, earth bus & earth bolts,

foundation flange - bolts-base Plates, sufficient nos. of hinged doors,

handles with locking arrangement and rubber gasket,heavy duty end

terminal connection,danger notice board,necessary ventilation,earthing strip

complete. The Panel shall be painted with epoxy powder coating. supplied

switch gears, BUSBARS, suitable size of inter connecting PVC copper

wire / copper-aluminium strips, rubber grommets, rib, bakelite control

fuses/MCB for measuring instruments, earth bus & earth bolts, foundation

flange - bolts-base Plates, sufficient nos. of hinged doors, handles with

locking arrangement and rubber gasket,heavy duty end terminal

connection,danger notice board,necessary ventilation,earthing strip

complete. The Panel shall be painted with epoxy powder coating.

(The rates excludes the cost of switchgears, bus bars, inter connecting

mains & Copper Aluminium strips, meters, Fuses etc. The dimension shall

be measured excluding base beams) The panel shall be supplied with

following approved manufacturers with following size.

(B) The standard companies switch gear shall be used and only

manufacturers at CPRI approved factory

(ii) with 550and

Providing mm. erecting

Depth XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Copper conductor for 1.1 KV. to be laid on wall with

493 100.00 necessary clamps or in existing trench / pipe at road crossing or floor of Mtr 215.13

following size of cable.

(A) 3 core 2.5 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Copper conductor for 1.1 KV. to be laid on wall with

494 650.00 necessary clamps or in existing trench / pipe at road crossing or floor of Mtr 287.85

following size of cable.

(B) 3 core 4 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Copper conductor for 1.1 KV. to be laid on wall with

495 1850.00 necessary clamps or in existing trench / pipe at road crossing or floor of Mtr 395.92

following size of cables.

(C) 3 core 6 Sq. mm

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Copper conductor for 1.1 KV. to be laid on wall with

496 315.00 necessary clamps or in existing trench / pipe at road crossing or floor of Mtr 676.70

following size of cables.

(A) 4 core 10 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Copper conductor for 1.1 KV. to be laid on wall with

497 315.00 necessary clamps or in existing trench / pipe at road crossing or floor of Mtr 1504.90

following size of cables.

(C) 4 core 25 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of cables

(D) 3 1/2 core 70 Sq. mm ( 35 Sq.1/2 mm core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of cables

(E) 3 1/2 core 95 Sq. mm ( 50 Sq. mm 1/2 core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of cables

(G) 3 1/2 core 150 Sq. mm ( 70 Sq. mm 1/2 core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of cables

(H) 3 1/2 core 185 Sq. mm ( 95 Sq. mm 1/2 core

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of cables

(J) 3 1/2 core 300 Sq.mm ( 150 Sq. mm 1/2 core)

Providing & laying approved make Double walled corrugated pipes

(DWC) of polyethylene(conforming to IS 14930 II )with necessary

503 200.00 connecting accessories of same material at required depth in existing Mtr 62.62

trench for laying of cable. below ground / road surface for enclosing

(A)50 mm outer dia

Providing & laying approved make Double walled corrugated pipes

(DWC) of polyethylene(conforming to IS 14930 II )with necessary

504 150.00 connecting accessories of same material at required depth in existing Mtr 137.36

trench for laying of cable. below ground / road surface for enclosing

(D)120 mm outer dia.

Providing and, fixing heavy duty flange type brass cable gland with rubber

ring for PVC insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables.

(A) 2 to 4 core 2.5 / 4 Sq. mm

506 125.00 (B) 2 to 4 core 6 Sq. mm EACH 38.38

507 125.00 (C) 2 to 4 core 10 Sq. mm EACH 38.38

508 125.00 (E) 2 to 4 core 25 Sq. mm EACH 51.51

Providing and, fixing heavy duty flange type brass cable gland with rubber

ring for PVC insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables.

(B) 3 & 1/2 core 35/50 Sq. mm

Solder less crimping type Aluminium lugs conforming to IS suitable for

cable of following size evenly crimped with high pressure tool & connected

515 50.00 to switchgear terminals with brass/cadmium plated nut bolts in an approved EACH 20.20

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Solder less crimping type Copper lugs conforming to IS suitable for cable

of following size evenly crimped with high pressure tool & connected to

521 150.00 switchgear terminals with brass/cadmium plated nut bolts in an approved EACH 8.08

Providing and fixing approved make Perforated C type cable tray. Made

from sheet steel. The cable tray should be single or double bended as per

required and as per IS 2062/1079 and shall be coated with hot dip

524 200.00 galvanizing as per IS 2629/4759. with max 17.5% perforation with coupler rmt 622.16

plate / Fish plate and GI hardware like nut - bolt and washers etc. erection

with necessary support( included) as per Specification and as per

instruction of engineer in charge..

(5) 300 X 50 X 2.0 mm Thick

Providing and fixing approved make 'T' Junction for Perforated C type

cable tray. Made from sheet steel. The Junction should be bended as per IS

2062/1079 and shall be coated with hot dip galvanizing as per IS

525 35.00 2629/4759. with max 17.5% perforation with coupler plate / Fish plate and EACH 291.89

GI hardware like nut - bolt and washers etc. erected on existing support as

per Specification and as per instruction of engineer in charge of following

(5) 300 X 50 X 2.0 mm Thick

Providing and fixing approved make '90° Elbow' for Perforated C type

cable tray. Made from sheet steel. The Junction should be bended as per IS

2062/1079 and shall be coated with hot dip galvanizing as per IS

526 35.00 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt EACH 245.43

and washers etc. erected on existing support as per Specification and as per

instruction of engineer in charge..

(5) 300 X 50 X 2.0 mm Thick 90° Elbow

Supply, Installation, Testing and Commissioning of suitable sweep, BEE

Star rated, Ceiling fan with Brush Less Direct Current (BLDC) permanent

ferrite magnet Motor, class of insulation: B, Rust free 3 nos.Aluminium

blades, 2 nos. canopies, shackle kit with earthing provision, copper

winding, Power factor not < 0.9, Service Value (CMM/W) minimum 6.85,

Air delivery minimum 215 CMM, 350 RPM,230v (tolerance as per IS :

527 365.00 374-2019), THD < 10%, compitible with electronic regulator unit for each 2629.03

Speed Control and all remaining accessories including safety pin, nut bolts,

washers, temperature rise = 75 degree C (Max.), suitable for 140 to

Voltage and rectifier circuit with surge, over current and overload

protection , 50 Hz, Single phase AC Supply, earthing etc. Complete as

required.[ Make shall be approved by Engineer in Charge] (A) 1200 mm

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe

528 365.00 down rod erected duly painted for fan complete with proper insulation each 108.07

without leakage and earthing.

Supplying & erecting Fan Hook of 10 mm M.S. Round bar grouted in RCC

slab with Making the site as original.

Supplying & erecting single phase approved make industrial exhaust fan

suitable for medium duty ring mounted low noise operation suitable for

medium duty having following dia size and maximum speed in RPM [A]

305 mm dia 900 RPM cat ii

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan

Supplying & erecting approved make low noise decorative exhaust fan

532 120.00 having square frame ABS body with inbuilt lowers & square frame.200mm each 1366.53

with 1350RPM Cat.II

Providing and erecting street light pole bracket comprising main B Class

MS pipe of 4.2 cm/require outside dia. complete with suitable B Class M.S.

sleeve tubing of approx. 45cms.length and suitable for 76.5 mm / 80mm. /

require size pole top having sufficient fasteners for fixing the brackets and

533 35.00 having spread of 1 mtr. length with suitable rise as per site condition & each 561.56

suitable welded stiffener reducer and nipple with check nut complete

painted with one coat of Red oxide / PU base primer and two coats of

Aluminium / PU paint. paint with following nos of arms.

[A] Single Arm bracket 1 Mtr

534 20.00 [B] Double Arm Bracket 1 Mtr each 758.51

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Painting of street light pole with bracket complete with two coats of

535 45.00 Aluminium paint for following size of pole. each 215.13

[a] up to 4 mtr

Supplying & erecting approved make Digital time switch having lithium

cell 6 years operative and operate battery backup 1 channel day clock with

14 memory programme, suitable to operate on 240V + 5%, 16A with,

536 3.00 floating contacts Minimum switching setup time 1 minimum & LCD each 3168.37

display. Also comprised permanent ON/OFF switching. Programming

switches & housed in fire proof thermoplastic enclosure & transparent

cover erected as required with necessary connection erected as directed.

Supplying and erecting approved make Octagonal pole made from HR

sheet steel. The pole should be made as per IS. and shall be coated with hot

dip galvanizing as per IS 2629/2633/4759, suitable suspend local wind

speed with integral Junction box consist of terminal plate of min 6mm

Hylam sheet, standard profile 35mmX7.5mm Din-Rail for MCB Mounting,

537 45.00 stud type terminal and arrangement for cable termination to be erected each 8192.11

With Suitable foundation (Included) as per details given by manufacturer

considering site requirement.

(D) 6 Mtr. Long 70 mm Top X 135 mm bottom dia, 3 mm thickness with

200mmX200mmX12mm base plate, 4-M20 Bolts and 600mm long with

necessary G.I. J Bolts .Approx Pole weight 59 kg

Supplying and erecting Direct On-line Electronics Starter with 2-5/4-10/8-

14/10-16 Amp. Rating relay (variable current setting) directly operated in

totally insulated elegant enclosure and 18 Amp. Rating power relay with

start - stop button for single phase operation up to 3 HP as per complete

538 7.00 erected on P.W. Block with following features. each 1603.88

Low voltage cut off below 140 V

High voltage cut off above 280 V

Overload protection

Indicating LEDs for motor on lv, hv & overload tripping. [Cat.II]

S.I.T.C. of single phase submersible pump set suitable for 100 mm size or

more dia bore well having motor capacity and discharge as under with

539 4.00 necessary panel box. Lifting and Lowering taken extra.(a) Motor rating 1 each 15595.41

HP (12 stage) pump having capacity of 50 LPM at 43 to 45 mtr head

suitable for 32 mm dia. delivery pipe Cat.II

Providing & erecting open well type horizontal mono block pump set with

stainless steel body having following specification (C) 1 H.P. single phase

open well motor pump set suitable for 185 LPM discharge @ 25 mtr. head,

suitable for 32 mm dia. Delivery pipe with control panel. Cat.II

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat

541 200.00 flexible Submersible copper cable approved make of following Size. (B) 3 Mtr 104.03

Core x 2.5 Sq. mm.

Supplying and erecting, commissioning and testing of Diesel Generating set

confirming to IS: 4722:1968 & BS:5514 having continuous rating,

phase, 415 volts, 50 cycles A.C. supply comprising of a totally enclosed

air/water cooled diesel engine with multi-cylinders developing suitable

BHP not less than following capacity at 1500 RPM with 10% overload for

one hour in 24 hours with standard accessories like fly wheel, lubricating

oil cooler, "A" class governor, heavy duty fuel wheel and lubricating oil

542 1.00 filter, oil bath air filler, lubricating oil pressure gauge, end exhaust EACH 1029194.04

manifold, standard set of tools with adjustable spanners, screw drivers,

cylinder head to cover, joint cylinder head to exhaust, element lube oil

filter, 12 / 24 volts electric starting equipment complete with standard

heavy duty battery, dynamo, cut-outs, ammeter, necessary wiring, pressure

gauge, starter etc and heavy duty Residential type exhaust silencer (With

DEF System) and vertical hot air duct both

(M) Continuous rating of 125 KVA ,BHP not less than 154 BHP

Providing & erecting approved make ATS panel suitable for following size

of 3 phase, 415 V., 50 cycles, A.C. diesel generating set complete of scope

as detailed below:

1) Power module: Motorised Changeover switch with ATS controller,

Auxiliary contactor with NO & NC contacts with Automatic Battery

Charger, indicating lamps for Generator ON, Mains ON, Load and suitable

control terminals and power terminals with neutral earthing studs.

(E) ATS Panel for 100/ 125 KVA 3 phase DG Set

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Providing and fixing printed instruction chart both in English and Gujarati

544 2.00 and duly framed with front glasses, for treatment of person suffering from each 130.29

Electric shock with minimum 50" diagonally size.

Supplying stand first AID box with antiseptic cream, medicine for use on

wounds due burn, crepe bandage, gauge bandage, medicated ready to use

545 2.00 bandage (Band-aid) adhesive tape for medicinal user, Scissors, anti-septic each 299.97

solution (Savlon or similar) etc. (All above contents shall be of standard

SITC of Vertical Air Termination Solid aluminium with Base- 10 mm dia

and 1000 mm long. Air Termination Base tested for conditioning, Ageing

546 2.00 Test & Lightning impulse current withstand test: 100 kA of 10/350µs each 9416.23

waveform in an accredited Third party laboratory as per 6.3 & 6.4 of IEC

62561-1 2017 protocol with MAST 34mm dia 3000 mm long- Cold

SITC of 8 mm dia solid Aluminium Conductor for roof top mesh grid and

tested as per IEC 62561- 2 conducted in the Govt. accredited thirty party

laboratory to meet the requirement of IS/IEC 62305 with Required

Accessories - Aluminium Holding clamp at every 1 mtr distance,

Aluminium/SS cross splicer at every crossing of Alu. conductor, Expansion

547 100.00 piece with connectors at every 20 mtr distance, Aluminium straight Splicer MTR 299.97

to connect conductors. All Accessories should be tested as per IEC 62561-

1 2018 Cl. 6.3 for conditioning & Ageing Test & 6.4 for Lightning

impulse current withstand test: 100 kA of 10/350µs waveform(Ageing &

Electrical test ) conducted in a sequence manner & tested in the Govt.

accredited Third party laboratory to meet the requirements of IS/IEC

SITC of 14.2 mm dia 3 mtr long Earth electrode of High tensile steel

electrode with 250 micron copper bonding & 1 bag of Carbon fill Based

environment friendly backfill tested as per IEC 62561-7 in NABL

548 8.00 accredited Laboratory and suitable stainless Steel double sided clamp. Eco Perset 5992.33

Friendly rust proof heavy duty weather proof Polyethylene Earth Pit

Chamber with following dimensions :254 mm dia (top), 330 mm dia

(bottom) & 260 mm (height).

Supply, Installation, Testing & Commissioning of following size of Grid

Tied Solar Power Plant with

Solar Panels (ALMM approved): Frame Material : Anodized Aluminum

alloy Frame With Twin Wall Profile, Front Cover : High Transmission

Low-Iron Tempered Glass (AR Coated), High efficency and positive power

tolerance Pmax: 0/+5, Module Efficiency should be approx. 18%-21%,

Normal operating temperature 45'C, Junction Box with Waterproof IP67 &

MC4 Compatible and Enclosed with Bypass diodes, 100%

Electroluminescence test to ensure error free Modules, Thep. temp. co-

efficient of the PV module shall equal or better than -0.45%/degree C.

Solar PV modules of minimum fill factor 75% to be used. Unit Production:-

4 to 5 Unit /kw /day (Actual)(1Year Avg) With 10 year Product warranty

and 25 year Linear Power Warranty.,

Solar Inverter: MPPT Range: 80-1000 V, Max efficiency: 97.5% - 98.9%,

O/p Frequency: 50/60Hz, Operating Altitude (m) ≤4000, O/p Power

Factor: ~1, O/P THDi: <3%, Operating Tempreture Range: -25~60°C, Anti-

islanding Protection:

ntegrated, Input Reverse Polarity Protection Integrated, Insulation Resistor

Supplying and Erecting Seamless Box Pipe of suitable size for rooftop

solar installations with good stability agaist wind, Thickness 2 mm and

micron, Hot Dipped Galvanized steel coils. suitable arrangement for base

plate for foundation , solar panel mounting, the structure should be suitable

for carry the load of solar panel,wiring, sprinkler system etc. with necessary

foundation work/wall mount, j bolt, anchor fastner etc. the nut bolt used for

installtion of stucture should be (SS 304) quality.

box. pipe ref. size (A) 40 x 40 x 2mm, (B) 50 × 50 × 2mm, (C.) 60 x 40 x

2mm,(D) 72 x 72 x 2.5mm: <3%, Operating Tempreture Range: -25~60°C,

Anti-islanding Protection:

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Providing & erecting Automatic solar panel cleaning system for solar

power projects which includes necessary plumbing work (UPVC pipes and

accessories) from source of water to project site (upto 30 meters),Suitable

551 35.00 size of sub mercible/ open well motor, necessary wiring for motor and Per KW 3681.45

sprinkler system with safety, timer circuit for automatically on/off the

sprinkler system, necessary size oand number of nozzles/JET (minimum

Nozzle/Jet per module).

(D) 21KW-50KW Cleaning System

The all inclusive comprehencive annual maintance contract cost covers

yearly maintanance of solar Pv Modules, Inverter,

wiring,earthing,switchgears, etc with material and labour cost including

preventive maintanance.The cost covers entire installation. AMC also

552 35.00 includes monthly site visit and inspection of project with submission of Per KW 4280.38

inspection and solar generation report. All parts should be

replaced/repaired if found faulty within specified time. Agency has to

provide necessory licening work for warranty,power,Bidirectional meter etc

(C ) 21KW-50KW System

GLR/ UG SUMP : GLR/ UG SUMP :Constructing U/G Sump at ltr

capacity Preparing structural design of RCC Under Ground / Partially

under ground / above high ground level Reservoir of required capacity as

per relevant I.S.s and constructing the same, including excavation in all

types of soil strata (including rock) including shoring strutting if required,

for loose soil / to protect from collapse due to near by traffic load, casting

100 mm thick P.C.C. leveling course in M-10, Refilling the pit with proper

soil and disposing of the surplus stuff within a lead of 50 meters. Including

cement plaster in CM 1:3 with approved water proofing compound to

inside water touching surface to container. Including all types of labour and

material charges of lowering, laying, erecting / hosting and jointing of pipe

assembly to inlet, outlet overflow, washout and bye pass arrangement as

per hydraulic design.

Providing and fixing accessories like MS / GI Ladder, CI Manhole frame

and cover, water level indicator, adequate cowl type ventilators or lantern

553 235100.00 type ventilator with stainless steel jail. SMT 30.30

B.B. Masonry chambers for valves. Providing and applying three coats of

cement paint / snowcem to the out side face of structure. It also includes

satisfactory water tightness test as per relevant I.S. code and painting name

of scheme and capacity on the tank as per direction of engineer in charge.

List of Indian Standards for Design of GSR / SUMP:-

The structural design of GSR shall be in accordance with provisions

(1) I.S. 3370, Part – 1 to 4, 1965 or latest revised.

(2) I.S. 456 – 2000 or latest revised.

(3) I.S. 1893 – 2000 – 1984 or latest revised.

(4) I.S. 875, Part – 1 to 3, 1987 or latest revised.

General Specifications:-

The minimum concrete grade for RCC shall be M-30.

TMT Fe 500 grade reinforcing bars confirming to I.S. 1786 / 1139 shall be

considered in design. TMT bars shall be provided. Any other steel can be

PUMP HOUSE :Designing (aestherically), and Constructing RCC framed

pump House in M: 25 mix. as per design , requirement and specification at

various site.incl. All associated civil works like conection to Sump through

inlet pipe, pumping machinery foundation, thrust block in pump house,

554 120.00 supporting work to heddermain ,Jungle cutting ,site clearance and debris SMT 2828.00

removal etc. complete.(with gantry girder suitable for 2 tonnes), Height of

pump house should be minimum 4.5 m from floor level, reinforcement /

steels should be TMT steel Fe-500 as per relevant IS only to be used.

pump house. 12mx 10 m

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Supplying and erecting approved make3 phase motor control panel (ATS)

made from 16 G. CRCA sheet duly painted with epoxy power paint inside

and outside with hinged doors and locking arrangement, consisting, of

suitable switch of AC 23 duty with HRC fuses (Cat.III), starting and

running contactors, overload relay, Automatic water level controller,

555 3.00 Electronic timer with master timer CT operated Ammeter with selector EACH 46868.04

switch, Voltmeter with selector switch, phase indicating lamps, single

phasing preventer , water level guard, over load, start, run and stop push

buttons, air cooled auto transformer with 60%, 70%, 80% tapping, Panel

to be erected on angle iron frame grouted on wall as directed., contactors

relays, timer etc. shall be of L & T Siemens / Cutler Hammer make. (C)

Suitable for 35 H.P.

Providing & erecting open well horizontal mono block pump set with cast

iron body, complete for three phase submersible motor having [K] For

556 1.00 HP 3 phase open well horizontal mono block pump set suitable for 2450 EACH 65517.69

LPM to 1575 LPM @ 40 to 51 MTR head suitable for 80 / 100 mm dia

delivery pipe Cat. II

2BHK Building pump house

Providing & erecting open well horizontal mono block pump set with cast

iron body, complete for three phase submersible motor having [E] For

557 1.00 HP 3 phase open well horizontal mono block pump set suitable for 1550 EACH 28512.30

LPM to 370 LPM @ 13.5 Mtr to 42 Mtr head suitable for 65/75 mm dia

delivery pipe Cat. II

2BHK Building pump house

S.I.T.C. submersible pump set suitable for bore of 150 mm dia or more

having 3 phase motor capacity not less than 10 HP with following capacity.

558 1.00 Lifting and Lowering taken extra. [C] 25 stage 160 to 100 LPM discharge EACH 52077.62

at 185 to 220 mtr head for 50 mm dia delivery pipe Cat.III

FIRE STATION FOR UG TANK

Supplying, Installation, Testing and commissioning of G.I class "C"

E.R.W pipes (as per IS:1239 / 3589 ) along with required all pipe fittings

and accessories like sockets, elbows, tees, flanges, gasket, reducers, nut-

559 40.00 bolts, U-bolt/Clamp, anchorfastner, plugs, nipples etc complete as Rmt. 3201.70

specified in technical datasheet.(Including: 10 % of all the welded joints

shall be done radiographically tested and 50% of the joints radiographed

shall be the "Field Joints")

Supplying, Installation, Testing and commissioning of Cast Iron body

Nitrile liner , SS Upper Lower stem, Teflon bushing RISING TYPE

563 2.00 SLUICE VALVE at PN 16 rating as per IS : 13095 complete with Nos. 32643.20

matching flanges bolt, nut, washer and other fittings accessories.

Supplying, Installation, Testing and commissioning of CIDF Non return

valve, Gun metal internals, Rubber sealed conforming to IS : 5312 (Part-1),

567 2.00 Swing type PN 1.6 rating with matching flanges bolt, nut and washer for Nos. 7211.40

pump house equipment.

Supplying, Installation, Testing and commissioning of CI STRAINER

569 4.00 with SS 304 Perforated sheet or screen with matching flanges bolt, nut and Nos. 15594.40

washer for pump house equipment.

150 mm dia. "Y"- Type

Supplying, Installation, Testing and commissioning of Gunmetal body IS:

571 2.00 318 LTB‐2, ball type 25mm BSPT fitting Air Release valve (ARV) with No. 4494.50

Isolation ball valve

Supplying, Installation, Testing and commissioning of Gun metal body,

572 2.00 spring type 25mm dia Pressure Release valve (PRV) with isolation ball No. 4898.50

valve (Calibrated at 8 Kg/Cm2)

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Supplying, Installation, Testing and commissioning of Bourdon type,

glycerine filled 100mm dial ( Range at 200 psi (16 bar), 304 stainless steel

573 6.00 with vent plug and polished stainless steel bayonet ring. Suitable for liquid Nos. 2727.00

filling. Welded case/ socket connection) pressure gauges having 15mm

NPT fittings with all accessories like isolation valve, bush etc.

Supplying, Installation, Testing and commissioning of Pressure switch of

approved make in pipe line suitable for line presure up 15kg/cm2 &

574 6.00 including connection with main panel etc. as required complete in all Nos. 3787.50

respects for Hydrant, Sprinkler, Standby and Jockey pump including

necessary wiring upto control panel & other materials.

Supply and Installation of MS steel for supports in pump room for the

supporting of valves, header, MCC panel and fuel tank etc.

Supply and Applying of Painting on pipe lines, equipments and valves like

576 2.00 Strainer, NRV, side pump room with two coats of enamel paint (As per the Lot 40400.00

IS:5,Sr No: 79,ISC no-536) over one coats of Red oxide primer.

Supplying, Installation, Testing and commissioning of air vessel of size

577 2.00 (400NB dia x2000MM long ) complete with drain, bottom tapping and top Set 40400.00

cap with air release

HYDRANT NETWORKvalve and pressure release valve

Supplying, Installation, Testing and commissioning of G.I class "C"

E.R.W pipes (as per IS:1239 / 3589 ) along with required all pipe fittings

like sockets, elbows, tees, flanges, gasket, reducers, nut-bolts, U-

bolt/Clamp, anchorfastner, plugs, nipples etc complete as specified in

technical datasheet. (Including: 10 % of all the welded joints shall be done

radiographically tested and 50% of the joints radiographed shall be the

"Field Joints")

578 380.00 Rates must be included with following job : Rmt. 2393.70

Pipes: All pipe fittings shall be as per IS: 1239 P-1and2, fittings below

50mm should be heavy ducty

Rediography: 10% of total field joint.

Holiday (wrapping coating) Testing: 100% U/G line

Phase wise hydrotesting at 11.2Kg/Cm2 for 3 to 4 Hours

Supply and Apply of Anti Corrosive Treatment for underground pipe with

581 120.00 primer and one coat of 4 mm minimum thick anti corrosive tape with black Rmt 1020.10

mastic paint after heating procedure.

Supply and Apply of Painting for aboveground lines with two coats of

582 428.00 enamel paint (As per the IS:5,Sr No: 79,ISC no-536) over one coats of Red Rmt. 373.70

oxide primer for above ground pipe line network.

Supplying, Installation, Testing and commissioning of Cast Iron body

Nitrile liner , SS Upper Lower stem, Teflon bushing Butterfly valve at PN

583 12.00 16 rating as per IS : 13095 complete with matching flanges bolt, nut, Nos. 7211.40

washer and other fittings accessories.

Supplying, Installation, Testing and commissioning of Gunmetal body IS:

585 8.00 318 LTB‐2, ball type 25mm BSPT fitting Air Release valve (ARV) with Nos. 4090.50

Isolation ball valve

Supplying, Installation, Testing and commissioning of SS made Hydrant

586 16.00 Valve as per IS:5290, Type-A Single headed, 63 mm dia complete with Nos. 5706.50

matching flange and fitting accessories.

587 16.00 Supply and Installation of SS Branch pipe with nozzle as per IS:903 Nos. 1969.50

Supplying, Installation, Testing and commissioning of Fire hose pipe,

588 19.00 RRL, Type-A, as per IS:636, 63mm dia x 15 Mtr. long, complete with SS Nos. 6565.00

male and female instantaneous coupling.

Supplying, Installation, Testing and commissioning of MS Hose box to

accommodate 2 lengths of hose pipes of 15 Mtr. Long and 1 No of branch

pipe with front openable glass door and glass for key complete with all

fittings and accessories.

Supplying, Installation, Testing and commissioning of 4 way fire brigade

590 4.00 inlet with CI body and GM coupling built in NRV complete with all Set 9241.50

fittings and accessories

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

Supply, fabrication,erection of MS steel for supports of fire hydrant

591 1000.00 network for T support of RCC block, hose box frame, and other surface Kg 252.50

supports for fire fighting line.

Supply and installation of First Aid fire hose reel of 25mm bore size,

592 15.00 Gunmetal IS:318 LTB2/ SS 304 Gr. I. Type -II, Complete with MS drum Nos 7423.50

and GM shutoff nozzle.

FIRE SPRINKLER SYSTEM

Supplying, Installation, Testing and commissioning of G.I class "B"

E.R.W pipes (as per IS:1239 / 3589 ) along with required all pipe fittings

like sockets, elbows, tees, flanges, gasket, reducers, nut-bolts, U-

593 56.00 bolt/Clamp, anchorfastner, plugs, nipples etc complete as specified in Rmt 1717.00

technical datasheet. (Including: 10 % of all the welded joints shall be done

radiographically tested and 50% of the joints radiographed shall be the

"Field Joints")

Supplying, Installation, Testing and commissioning of Heavy lever

operated butterfly valve, at PN 1.6 complete with matching flanges bolt,

nut and washer.

Supplying, Installation, Testing and commissioning of Drain Assembly

with isolation valve of 32mm dia ball valve

Supplying, Installation, Testing and commissioning of MS steel for

601 1000.00 supports for main sprinkler header, distribution line, branch pipe and arm Kg 252.50

Supply, apply of Painting of aboveground lines with two coats of enamel

602 698.00 paint over & one coats of Red oxide primer for above ground pipe line Rmt. 323.20

network. (Fire red color, Shed No 536 / IS:5)

603 22.00 Supplying, Installation, Testing and commissioning of Fire sprinkler Nos. 757.50

nozzle @ 68 degree temp. rating standard responce Pendent type (K-5.6) .

Supplying, Installation, Testing and commissioning of SS flexidrop of

604 400.00 appropriate length Ro 1797.80

605 170.10 Excavation and back Filling for following soil condition for underground M3 222.20

fire line of 1.2 Mtr deep from the ground level.

606 3.00 Hard Soil /rock soil M3 119.18

Supply and making PCC pedestal blocks for above ground pipe line

network dully grouted 600mm below the ground level and 300mm above

ground level of size 300mm wide with grouted- ISMC 100 x 50 x 6mm to

607 19.00 clamp the pipe line on the block. (MS steel quantity is given in separate Nos 2828.00

Making of Core Cutting with various slab height for fire riser

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

less CONTROL PANEL FOR PUMPS

Supplying, Installation, Testing and commissioning of Motor control

center for above mentioned Electrical pump (1 Nos), Sprinkler pump (1

Nos) and jockey pump (1 Nos),Diesel Pump (1Nos) and complete with

incomer, Star delta starter, protective fuses, indicating lamps with interlock

facility with top/ bottom entry with foot mounting type complete with all

accessories. Separate cabinet for diesel engine pump having battery charger

with start, stop, accept, and test push button (for 1 sets of DG pumps) . All

the components shall be housed in a common cubical made of 16 swg. M.S.

611 1.00 sheet with required stiffeners ( if required).The panel shall be powder Nos. 244652.30

coated of approved colour both inside & outside. The panel shall have both

bottom & top cable entry provisions and panel shall be mounted on

Pedestal of 300 mm height. including 1 coat Corrosion resistance & two

coats of red enamel paint complete. Including MS Base frame, Soft Starter

for Main Pump, Local Hooter for Alarm. MCC panel should have

following mechanisum for pumps, (a) Jockey Pump: Auto start - Auto

stop, (b) Main Pump : Auto Start - Manual Stop, (C) DG pump - Manual

Supplying, Installation, Testing and commissioning of Cabling and earthing

From control panel to main pumps -1 nos , Jockey pumps- 1 nos , pressure

612 1.00 switches, from DG control panel to DG pump local panel for controls and LOT 69235.50

battery charger with 25 x 3mm thick GI strip for double earthing of the

panel and motor.

Supplying, Installation, Testing and commissioning of ABC Dry Powder

613 16.00 type - 6Kg. capacity as per IS:15683 (complete with zebra painting - on Nos 2929.00

Supplying, Installation, Testing and commissioning of

614 16.00 CO2 type - 4.5Kg. capacity as per IS:15683 (complete with zebra Nos 5504.50

painting - on background)

Supplying, Installation, Testing and commissioning of safety and

emergency escape signages board.

Supplying, Installation, Testing and commissioning of fire bucket

complete with canopy (4 bucket with stand and canopy)

Supplying, Installation, Testing and commissioning of 4 loop Conventional

fire alarm/detection control panel.

Supplying, Installation, Testing and commissioning of Photoelectric

618 12.00 smoke detector Complete with LED, complete with Mounting Base Nos 2222.00

Complete as required Conforming to IS.

Supplying, Installation, Testing and commissioning of Photoelectric Heat

619 0.00 detector Complete with LED, complete with Mounting Base Complete as Nos 2888.60

required Conforming to IS.

Supplying, Installation, Testing and commissioning of Hooter complete

with Mounting Base as required conforming to IS

Supplying, Installation, Testing and commissioning of Conventional Type

621 18.00 Manual Call Point having Surface or flush mounting Option Complete as Nos 2923.95

required conforming to IS Standards

Supply & Laying of 2core, 1.5 sq. mm. stranded copper conductor, pvc

622 2100.00 insulated PVC sheathed, aluminum myler tape shielded FRLS wire Mtrs. 131.30

Supply & installation of Mounting Base, DC gland,Hood, Junction boxes,

saddle, and other cable fittings

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

[1]GEAR LESS LIFT DRIVE (MRL) comprising of High Starting torque

Lift 3 phase 440 V A. C. Permanent Magnet Synchronous motor of proper

rating with high efficiency shall be used.[2] Micro processor based / PLC,

ACVVVF, vector control drive with encoder feedback closed loop system

shall be used for lift car and door operation which shall be full collective

selective operation hall call demand response, UP/DOWN hall stops, Main,

Up/ Down Contactor with overload and phase reversal relay and safety

controls.[3] Car with M S platform with bracings of adequate size and to

sustain the impact load cabin + passenger with safety factor of fire for steel

and side panels of Stainless steel of sheet of grade 304 duty. Car ceiling

will be S.S. finishes with aesthetic appearance with LED ceiling lights. Car

flooring shall be of s/s 304 chaker plate design sugeested of engineer in

charge. of engineer in charge. Car doors shall be of stainless steel grade

304, hairline finish with centre opening / telescopic automatic doors. Car

panel will also be S.S. 304 finished with emergency stop device,

mechanical door safety device, facility of auto/ attended mode. All car

panel buttons and all floor switches must be with brail language as per lift

act.[4] All landing doors must be fire rated for 2 hour shall be fully

automatic centre opening/ telescopic opening made of hairline finish steel

grade of 304 with key holes and infrared curtains with Unlocking facility

from outside [5] Appropriate battery operated emergency light in the car

along with alarm switch shall be provided. Also, Emergency Light & Fan

should start immediately without any Time Delay as soon as power fails.

[6] Digital scrolling indicator system for up-down arrow along with floor

[1]GEAR LESS LIFT DRIVE (MRL) comprising of High Starting torque

Lift 3 phase 440 V A. C. Permanent Magnet Synchronous motor of proper

rating with high efficiency shall be used.[2] Micro processor based / PLC,

ACVVVF, vector control drive with encoder feedback closed loop system

shall be used for lift car and door operation which shall be full collective

selective operation hall call demand response, UP/DOWN hall stops, Main,

Up/ Down Contactor with overload and phase reversal relay and safety

controls.[3] Car with M S platform with bracings of adequate size and to

sustain the impact load cabin + passenger with safety factor of fire for steel

and side panels of Stainless steel of sheet of grade 304 duty. Car ceiling

will be S.S. finishes with aesthetic appearance with LED ceiling lights. Car

flooring shall be of s/s 304 chaker plate design sugeested of engineer in

charge. of engineer in charge. Car doors shall be of stainless steel grade

304, hairline finish with centre opening / telescopic automatic doors. Car

panel will also be S.S. 304 finished with emergency stop device,

mechanical door safety device, facility of auto/ attended mode. All car

panel buttons and all floor switches must be with brail language as per lift

act.[4] All landing doors must be fire rated for 2 hour shall be fully

automatic centre opening/ telescopic opening made of hairline finish steel

grade of 304 with key holes and infrared curtains with Unlocking facility

from outside [5] Appropriate battery operated emergency light in the car

along with alarm switch shall be provided. Also, Emergency Light & Fan

should start immediately without any Time Delay as soon as power fails.

[6] Digital scrolling indicator system for up-down arrow along with floor

Item Estimated but Tender Total Amount Accoring

Item Estimated but Tender Total Amount Accoring

No. may be more or Rates to estimated quantities

[1]GEAR LESS LIFT DRIVE (MRL) comprising of High Starting torque

Lift 3 phase 440 V A. C. Permanent Magnet Synchronous motor of proper

rating with high efficiency shall be used.[2] Micro processor based / PLC,

ACVVVF, vector control drive with encoder feedback closed loop system

shall be used for lift car and door operation which shall be full collective

selective operation hall call demand response, UP/DOWN hall stops, Main,

Up/ Down Contactor with overload and phase reversal relay and safety

controls.[3] Car with M S platform with bracings of adequate size and to

sustain the impact load cabin + passenger with safety factor of fire for steel

and side panels of Stainless steel of sheet of grade 304 duty. Car ceiling

will be S.S. finishes with aesthetic appearance with LED ceiling lights. Car

flooring shall be of s/s 304 chaker plate design sugeested of engineer in

charge. of engineer in charge. Car doors shall be of stainless steel grade

304, hairline finish with centre opening / telescopic automatic doors. Car

panel will also be S.S. 304 finished with emergency stop device,

626 1.00 mechanical door safety device, facility of auto/ attended mode. All car Ea. 1777293.97

panel buttons and all floor switches must be with brail language as per lift

act.[4] All landing doors must be fire rated for 2 hour shall be fully

automatic centre opening/ telescopic opening made of hairline finish steel

grade of 304 with key holes and infrared curtains with Unlocking facility

from outside [5] Appropriate battery operated emergency light in the car

along with alarm switch shall be provided. Also, Emergency Light & Fan

should start immediately without any Time Delay as soon as power fails.

[6] Digital scrolling indicator system for up-down arrow along with floor

position indicator shall be provided inside the car and at all floors. [7] Full

height infra red curtain with multiple cross / crossing light beams shall be

provided. [8] Automatic Rescue Device (ARD) shall be provided

accordingly of passenger capacity with Manual Rescue Operation ( Manual

Cranking Facility). [9] Audio visual indication in the lift car showing over

loading shall be provided such that doors kept open till excess load is

removed.[10] Spring buffers/PU Buffers shall be provided. [11] Car fan as

Total Amount Say.

Total Amount Say.

I/ We am/ are willing to carry out the work @ _____________ % above /Below __________Percentage (should be written in figures and words) of the

* Estimated Amount * Estimated Amount

Put On Tender Rs. 15,85,27,830.00 Put On Tender Rs.

Deduct…………% Below Rs. ………………………. Add …………% Above Rs. ……………………….

(* Please strike out whichever is not applicable.)

Note 1: All works shall be carried out as per public works department handbook and other sepecifications of division or as directed.

Note 2: All the columns is Schedule should be filled in ink and the total of the entries in the last column should be struck by the contractor under his

Note 3: Rates quoted include clearance of site (prior commencement of work and at its close) in all respects and hold good for work under all conditions,

site, moisture, weather etc.

Note 4: To be continued on additional sheets, if found necessary.

Name of Work : Construction of Fire station with staff quarters at Harni TP 1 FP 143, North Zone

Item Estimated but Total Amount Accoring

Item Estimated but Total Amount Accoring

Item Work Unit Tender Rates

No. may be more or to estimated quantities

Signature of Contractor with Seal Signature of Contracting Authority with Seal