Loading…
Loading…
Tender Value
₹28.7 Cr
EMD Value
₹28.7 L
Closing Date
4 Jun 2026, 6:00 pmClosed
Executive Engineer, Navrangpura (R&B) Division, Ahmedabad
Construction of New Hostel Building of Gujarat Arts and Science College at Gujarat College Campus, Ahmedabad.
303770
02 of 2026-27
Open
Civil Works - Buildings
Ahmedabad
7 documents required · 7 mandatory
₹18,000
Executive Engineer, Navrangpura (R and B) Division, Ahmedabad.
₹28.7 L
9 May 2026
9 May 2026
9 May 2026
4 Jun 2026
9 May 2026
Item No. Quantity Unit Rate in Figures
specifications) Amount
1 Excavation for foundation upto 1.5 m depth including sorting out and 4453.000 Cumt 116.82
stacking of useful materials and disposing off the excavated stuff upto All
lift and lead.(A) Loose or soft soil
2 Excavation for foundation for depth from 1.5 m to 3.0 m including 2591.000 Cumt 162.38
sorting out and stacking of useful materials and disposing off the
excavated stuff upto All lift and lead .(B) Dense or Hard soil
3 Filling in foundation and plinth with sand in layers of 20 cm. Thickness 259.000 Cumt 460.19
including watering ramming and consolidating etc. comp.
4 Filling available excavated Earth (Excluding Rock) in trench plinth side of 3244.000 Cumt 130.39
foundation . in layer not excluding 20 cm in depth consolidation each
deposited layer by ramming and watering etc. complete
in thickness including ramming watering and consolidating etc. complete
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
6 Applying general insecticide pest control treatment to floors, cupboards 7852.000 Sqmt 89.28
etc including labour material etc. complete. Using Imidacloprid 30.5 SC.
As Per 6113 Part -II (0.075% concentration by mass) is recommended
10.5ml chemical diluted with 5 liters of water application 0.5 liters
chemical/ sqm of surface is recommended as per I.S.
7 Anti-Termite System: Providing and laying of permanent piping technology 1019.000 Sqmt 134.33
anti-termite treatment before flooring work by installing LLDP (Low linear
density polyethylene) tube of 8 mm O.D. & 6.4 mm I.D. with inbuilt
pressure compensation chip every 30 cm interval in the tube, having
working pressure of 2 Kg/cm² and release rate of 1.9 ltr/hour fixed by P-
clips and nails. The LLDP pipe shall be installed at the entire periphery of
the building and at internal network of building at a depth of 20 to 200 mm
under floor at every 2 to 3 mtr. c/c distance (adjusted as per building
layout) & ends of loop pass through a PVC elbow of minimum 32 mm ID
at junction box of wall and floor level, entering into a steel reinforced
grooved flexible pipe of minimum 22 mm ID leading into junction box and
the loops shall terminate in junction boxes & test every junction during
injecting chemicals for termite control treatment. The anti-termite chemical
Imidacloprid 30.5% SC - Sq.mt 133.00 mix as per IS-6313 (part III) shall
be injected by the pressure pump diluted with water @ 10.5 ml/5 ltr of
water at the rate of 2 Kg/sq.cm @ 5 ltr/SMT. The contractor shall submit
approved line plan for piping system and junction boxes dully approved by
Engineer-in-Charge with bond of 5 year warranty. (i) Anti-termite chemical
injected area (Chemical injecting incl. labour cost).
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
8 Providing and laying in position Ready Mixed M-150 grade concrete for 885.210 Cumt 4226.95
reinforced cement concrete work in Foundations & Plinth, using cement
content as per approved Design Mix manufactured in fully automatic
batching plant established on site and transported to site of work in transit
mixer having continuous agitated mixer, manufactured as per mix design
of specified grade for reinforced cement concrete work including pumping
of R.M.C. from transit mixer to site of laying, excluding the cost of
reinforcement and including cost of centering. shuttering, formwork
finishing and admixtures in recommended proportions as per IS : 9103 to
accelerate/ retard setting of concrete, improve workability without
impairing strength and durability as per direction of the Engineer -In -
Charge. Without Fly Ash (Min cement level as per latest IS 456 shall be
maintained) For All Floor Level
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
9 Providing and laying in position Ready Mixed M-200 grade concrete using 161.000 Cumt 5859.11
cement content as per approved Design Mix manufactured in fully
automatic batching plant established on site and transported to site of
work in transit mixer having continuous agitated mixer, manufactured as
per mix design of specified grade for reinforced cement concrete work
including pumping of R.M.C. from transit mixer to site of laying, excluding
the cost of reinforcement and including cost of centering. shuttering,
formwork finishing and admixtures in recommended proportions as per IS
: 9103 to accelerate/ retard setting of concrete, improve workability without
impairing strength and durability as per direction of the Engineer -In -
Charge. Without Fly Ash (Min cement level as per latest IS 456 shall be
maintained) For Plinth slab and all R.C.C. memebers at all floor level
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
10 Providing and laying in position Ready Mixed M-250 grade concrete using 6644.130 Cumt 6650.04
cement content as per approved Design Mix manufactured in fully
automatic batching plant established on site and transported to site of
work in transit mixer having continuous agitated mixer, manufactured as
per mix design of specified grade for reinforced cement concrete work
including pumping of R.M.C. from transit mixer to site of laying, excluding
the cost of reinforcement and including cost of centering. shuttering,
formwork finishing and admixtures in recommended proportions as per IS
: 9103 to accelerate/ retard setting of concrete, improve workability without
impairing strength and durability as per direction of the Engineer -In -
Charge. Without Fly Ash (Min cement level as per latest IS 456 shall be
maintained) for all RCC elements like Footings , Mass concrete , Column
up to GL , Ground/Plinth Beam Plinth Slab, Columns, Beam, Chhajja,
Lintal, Slab, Stair, RCC Wall, Coping etc. For All Floor
11 Extra for concreting in grade M350 instead of M250 including cost of 1126.000 Cumt 273.57
cement, labour etc. complete.
12 Extra for concreting in grade M300 instead of M250 including cost of 193.000 Cumt 182.38
cement, labour etc. complete.
13 Providing IS Mark TMT FE-550D bar reinforcement for RCC work 865575.240 Kg 99.08
including bending & placing in position complete up to All floor Level
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
14 Providing and fixing 90 cm Height Stainless Steel Railing made from 243.000 Rmt 4332.29
anticorrocive 304 grade S S pipe of 50 mm dia (16 Gauge) as hand rail
with S S 304 grade Baluster of 40 mm dia (16 Gauge) as a vertical
support fixed in RCC slab at 1.2m c/c including three horizontal S S
pipes of 25 mm dia (16 Gauge) at eqal distance fixed by 18.75 mm dia (16
Gauge) S S pipe with baluster including accessories as per detailed
drawing as directed etc. complete.
15 Providing and fixing 30 cm Height Stainless Steel Hand Railing made 306.000 Rmt 1969.50
from anticorrocive 304 grade S S pipe of 50 mm dia (16 Gauge) as hand
rail with S S 304 grade Baluster of 40 mm dia (16 Gauge) as a vertical
support fixed in RCC member at 1.2m c/c S S pipe with baluster including
accessories as per detailed drawing as directed etc. complete.
16 Brick work using common burnt clay building bricks having crushing 182.000 Cumt 4021.02
strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement
Mortar 1:6. (1- Cement : 6 -fine sand) (B) Conventional below plinth
17 Brick work using common burnt clay building bricks having crushing 3373.000 Cumt 4441.78
strength not less than 35 kg./Sq.Cm. for superstructure above plinth level
upto floor two level in Cement Mortar 1:6. (1- Cement : 6 -fine sand) (B)
Conventional for All Floor
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
18 Half Brick masonry in common brunt clay building bricks having crushing 3960.000 Sq m 674.78
strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -
coarse sand ) in foundation and plinth (B) Conventional in super structure.
for All Floor
19 Providing and fixing 150 mm wide, approved quality chicken wire mesh at 6128.000 Sqmt 295.12
junction of brick work and RCC work or two dissimilar surfaces, at all
heights fixed by nails, rowal plugs or tag before applying the plaster,
including curing, scaffolding all complete as directed.
20 Providing 20 mm thick double coat mala cement plaster on interior brick / 28722.000 Sqmt 374.81
concrete work for plastering comprising of base coat of 12 mm thick
cement plaster in cement mortar (1 Cement : 4 coarse sand) in rough
finishing and 8 mm thick top coat of cement mortar 1:2 (1 Cement :
Coarse sand) finished with trovel including scaffolding curing and 10mm
grooves etc. complete.. ForAll Floor
21 Providing 10 mm. Thick mala cement plaster in single coat for plastering 9738.670 Sqmt 250.18
on ceiling and soffits of stairs and finished with trovel in : (I) Cement
mortar 1:4 (1 cement : 4 sand) smooth mala finish and 10mm grooves
etc. complete. All Floor
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
22 20 mm thick Sand faced cement plaster with 1cmx1cm grooves as 14079.000 Sqmt 342.79
suggested by this office consisting of 12 mm thick backing coat of C.M.
1:3 ( 1 cement : 3 coarse sand ) and 8 mm thick finishing coat of C.M. 1:1
( 1 cement : 1 coarse sand) and 18mm wide & 8mm deep groovesfor all
heights as directed etc. complete. and as per pattern sample aprroved by
the architect or directed engineer in-charge
23 Providing throating or plaster drip and moulding to R.C.C. Chhajja. 2065.000 Rmt 41.66
24 Applying two coats of Acrylic lapy (putty) & two coats of primer of 38313.000 Sqmt 40.59
approved brand and manufacture on new wall surface to give an even
shade including thoroughly brushing the surface free from mortar dropping
and other foreign matter and sand papered smooth.
25 Wall painting (two coats) with plastic emulsion paint of approved brand 28542.000 Sqmt 79.22
and manufacture on undecorated wall surface to give an even shade
including throughly brushing the surface free from mortar droppings and
other foreign matter and sand papered smooth.
26 Painting (two coats) with plastic emulsion paint of approved brand and 9771.000 Sqmt 84.64
manufacture on undecorated ceiling surface to give an even shade
including throughly brushing the surface free from mortar droppings and
other foreign matter and sand papered smooth.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
27 Wall Painting (Two coats) with 100% weather proof acraylic emulsion 14007.000 Sqmt 124.63
paint of approved brand and manufacture and of required shade on
exterior wall surface to give an even shade over and including primery
coat with Alkaly resistance primer of approved brand after thoroughly
brushing surface to remove all dust and remains of loose powdered
material etc. copm. for all height
28 White washing with lime on wall surface (two coats) to give an even shade 571.000 Cumt 12.41
including thoroughly booming the surface to remove all dirt, dust; mortar
drops and other foreign matter.
29 Forming groove of uniform size from 10 x 10 mm and upto 25 x15 mm in 12587.000 Rmt 52.32
plastered surface as per approved pattern using wooden batten, nailed to
the under layer including removal of wooden battens, repairs to the edges
of plaster panel and finishing the groove complete as per specifications
and direction of the engineer incharge..
30 Providing And filling with good quality cinder (steam coal) as directed by 194.000 Cumt 555.50
engineer in charge in sunks in layers of 15 cm thick,including
watering,placing ,ramming well etc as directed, for all floor.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
31 Providing Water proofing Treatment on Sunk Slab including cement 1246.000 Sqmt 369.46
concrete flooring 1:2:4 (1-cement : 2-coarse sand : 4-graded stone
aggregate 20mm nominal size) laid in one layer and finished with a 1:3 (1
cement : 3 Mortar ) floating coat of neat cement average 50mm thick to
Prepare slope including water proofing chemical etc. Complete for Sunk
Slab All Floor.
32 Providing and laying broken chine mosaic flooring for terrace using 12 mm 1135.000 Sqmt 747.29
to 20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3
to plain or slope and to be tempered to bring mortar creme out upto
surface using white cement including rounding off junctions and extending
them upto 15 cm along the wall,clearing with water and oxalic acid etc. as
33 Providing and laying cement concrete flooring 1:2:4 (1-cement : 2-coarse 1135.000 Sqmt 351.56
sand : 4-graded stone aggregate 20mm nominal size) laid in one layer and
finished with a floating coat of neat cement. (A) 50mm thick.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
34 Providing Plinth Protection to Building including excavation in ordinary soil 332.000 Sqmt 2240.48
and laying cement concrete 1:3:6 using stone aggregates of 40mm
nominal size in foundation layer 125 mm thick+ 125mm thick sand layer
below pre-cast Rubber Dye inter locking concrete block 60mm thick with
grade of concrete M300 pneumatic compressed by mechanically pressed
and as per approved design including 75mm Sand layer for levelling and
filling the joint with sand in proper line and level etc. complete, Including
Providing and fixing pre-cast concrete kerb stone of grey cement based
concrete block 30cm length, 30cm height and 15cm thick made of M250
grade concrete as per approved design and including excavation for fixing
in proper line and level, filling the joint with C:M 1:3 (1cement:3 fine sand)
etc. complete.
35 Providing & fixing in position standard extruded Aluminum Four track 62.000 Sqmt 3781.44
Window( 4 shutter + 1 Mosquito net Shutter) with Standard Extruded
Colour Anodied Alluminium Section Equivalent to Jindal Series E (30mm)
Section Numbered: Frame -Bottom with Weep Holes -20928, Frame Top
& Side-20837 ,Shutter Top & Bottom 20993, Shutter Inter Lock -20550
,Shutter Side (handle) -20549 With 5mm thick Transparent Tinted Float
Glass With EPDM Rubber Gasket, Air Lock Stirip dd another shutter fitted
with SS wire mosquito mesh jali in the same Aluminium shutter section
and Finishing , Joint With Section Sealant, With Power Coated Standard
Alluminium Fitting.with as per window size including all required materials
labours and equipments as per detailed drwg. as directed.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
36 Providing and fixing in position standard extruded Aluminium three-track 141.000 Sqmt 4009.70
sliding window system (3 shutters + 1 mosquito net shutter) made of
colour anodized extruded Aluminium sections equivalent to Jindal Series
E (30 mm), with section numbers: Frame Bottom with weep holes –
20928, Frame Top & Side – 20837, Shutter Top & Bottom –
Shutter Interlock – 20550, Shutter Side (handle) – 20549. The shutters
shall be fitted with 5 mm thick transparent tinted float glass fixed with
EPDM rubber gaskets, and one shutter fitted with SS wire mosquito mesh
jali in the same Aluminium shutter section. The system shall include air
lock strip, sealant at all joints, and finishing with powder-coated standard
Aluminium fittings, complete as per window size and detailed drawings.
The rate shall include cost of all materials, labour, fittings, equipment, and
accessories, and the work shall be carried out as directed by the Engineer-
in-Charge.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
37 Providing and fixing in position standard extruded Aluminium three-track 624.000 Sqmt 4481.37
sliding window (2 shutters + 1 mosquito net shutter) made of colour
anodized extruded Aluminium sections equivalent to Jindal Series E (30
mm), comprising: Frame Bottom with weep holes – Section No.
Frame Top & Side – Section No. 20837, Shutter Top & Bottom – Section
No. 20993, Shutter Interlock – Section No. 20550, and Shutter Side
(handle) – Section No. 20549. The shutters shall be fitted with 5 mm thick
transparent tinted float glass fixed with EPDM rubber gasket, and one
shutter provided with SS wire mosquito mesh jali in the same Aluminium
shutter section. The system shall include air lock strip, joint sealing with
approved sealant, and finishing with powder-coated standard Aluminium
fittings, complete as per window size and detailed drawings. The rate shall
be inclusive of all materials, fittings, fixtures, labour, equipment, and
accessories, and the work shall be carried out as directed by the Engineer-
in-Charge.
38 Providing and fixing openable Aluminium casement window made from 238.000 Sqmt 4583.58
standard extruded colour anodized Aluminium sections, with frame
members (bottom, top and sides) of Jindal Section No. 20630 and
openable shutters made of single-glass shutter members (top, bottom and
sides) of Jindal Section No. 20727, including glazing clip member Jindal
Section No. 19359. The shutters shall be fitted with 5 mm thick
transparent plain float glass, fixed with EPDM rubber gaskets and
transparent silicon sealant. The work shall include providing and fixing
S.S. hinges, S.S. handle of 150 mm, S.S. stopper 200 mm long, and all
necessary fittings, fixtures and accessories, complete as per approved
drawing and as directed by the Engineer-in-Charge.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
39 Providing & Fixing in position standard extruded approved colour anodised 103.000 Sqmt 3443.80
Aluminum Ventilation with outer frame section 20125 Stander Box Frame
@ Wt 0.861 kg/Rmt with 5mm thick fixed ground glass fixed to alluminium
strip blade fixed or adjestable ventilation & Providing and fixing Nylon
Mosquito net with stitching on wall as per ventilation size, including all
required materials, fixtures, fastenning, labours and equipments as per
detailed drawing as directed. For Ventilators
40 Providing and fixing entrance wooden hollow two-leaf flush door shutter 17.000 Sqmt 8641.56
with wooden frame 250 mm × 50 mm. The shutter shall be fabricated with
teakwood frame members of size 50 mm × 150 mm, incorporating 6 nos.
horizontal and vertical rails of size 50 mm × 50 mm, covered on both sides
with 6 mm thick waterproof plywood, finished with 1 mm thick decorative
laminate on both sides. Necessary teakwood battens shall be provided,
with the door frame and edges finished with one coat of primer and two
coats of enamel paint, shade as approved by the Architect. The door shall
be provided with floor spring pivot, 600 mm long stainless steel handles on
both sides, approved locking systemn, and each shutter fixed with 4 nos.
150 mm long stainless steel hinges. The item shall include all materials,
fittings, fixtures, fastenings, and accessories, and shall be completed in all
respects as per approved design, drawing, and as directed by the
Engineer-in-Charge.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
41 Providing and fixing 38 mm thick flush double door shutter, solid core type, 6.000 Sqmt 3678.42
conforming to IS:2202 and ISI approved, with one-third width of each
shutter designed as a full-height glazed panel using anodized Aluminium
section (weight not less than 1.1 kg/m) of size 63.5 mm × 38 mm, fitted
with 5 mm thick frosted/clear glass as specified. The shutter shall be
mounted in a wooden door frame of size 100 mm × 50 mm for durable grip
of hinges. Each shutter shall be finished with 1 mm thick decorative
laminate on both sides of the non-glazed portion, with machine-glued PVC
banding on the periphery. The work shall include providing and fixing fixed
glazing portion, 600 mm long stainless steel handles on both sides,
stainless steel fixtures, locking arrangement of approved standard make or
equivalent, 4 nos. 150 mm long stainless steel hinges per shutter, and all
necessary fixtures and fasteners. The rate shall include all materials,
fittings, fixtures, glass, labour, equipment, and accessories, complete as
per approved drawings and as directed by the Engineer-in-Charge.
42 Providing and fixing 38 mm thick flush single door shutter, solid core type, 458.000 Sqmt 5054.04
conforming to IS:2202 and ISI approved, mounted in a wooden frame of
size 100 mm × 50 mm for durable grip of hinges. The shutter shall be
finished with 1 mm thick decorative laminate on both sides, with machine-
glued PVC banding on the periphery. The work shall include providing and
fixing 600 mm long stainless steel handles on both sides, stainless steel
fixtures, locking arrangement of approved standard make, and fixing of
nos. 150 mm long stainless steel hinges per shutter. All fittings, fasteners,
accessories, labour, and materials shall be included, with sample and
shade approved by the Engineer-in-Charge.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
43 Providing and fixing FRP frame size 100 x 50 mm and 35 mm thick ( Fiber 217.000 Sqmt 2363.40
Glass with PUF Injection ) FRP depress panel Single or Double shutter
having extra reinforcement on sides & edges in Gel coat finish.The core of
the both shutter & frame is to be filed up with injected fire retradat grade
polyurethene foam done in situ along with embeded wooden pieces for
stiffening & also taking hinges & fintures.The whole FRP frame & single or
double shutter is to be waterproof, weatherproof, termite proof &
resistance to mild acid/alkali. Rates are to be inclusive of S.S hinges with
necessary screws & S.S fixtures & fastenings & fartener sleeve.Colour
and Shade approved by Engineer-In-Charge.
44 Providing and placing 0.6m x0.6m Glazed Vitrified Tile (G.V.T) vitrified 8 1973.000 Sqmt 1344.31
mm thick tile flooring over 20 mm (average) base of cement mortar 1:6 (
cement: 6 coarse sand) on new surface or fixing on existing flooring by
adhesive material including dismentaling of existing flooring and jointed
with color cement slurry including finished with flush pointing & cleaning
the surface etc. complete in Two colour pattern or as per directed engineer
incharge.(tack 10% DARK shade)
45 Providing and placing 0.6m x0.6m Glazed Vitrified Tile (G.V.T) vitrified 8 146.000 Sqmt 1223.11
mm thick tile skirting over 12 mm (average) base of cement mortar 1:3 (
cement: 3 coarse sand) on new surface or fixing on existing flooring by
adhesive material including dismentaling of existing flooring and jointed
with color cement slurry including finised with flush pointing & cleaning the
surface etc. complete in Two colour pattern or as per directed engineer
incharge.(tack 10% DARK shade)
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
46 Providing and placing 0.6m x0.6m Polished Vitrified Tile (P.V.T) vitrified 8 3451.000 Sqmt 1325.12
mm thick tile flooring over 20 mm (average) base of cement mortar 1:6 (
cement: 6 coarse sand) on new surface or fixing on existing flooring by
adhesive material including dismentaling of existing flooring and jointed
with color cement slurry including finished with flush pointing & cleaning
the surface etc. complete in Two colour pattern or as per directed engineer
incharge.(tack 10% DARK shade)
47 Providing and placing 0.6m x0.6m/0.3m Polished Vitrified Tile (P.V.T) 1008.000 Sqmt 1201.90
vitrified 8 mm thick tile skirting over 12 mm (average) base of cement
mortar 1:3 ( 1 cement: 3 coarse sand) on new surface or fixing on existing
flooring by adhesive material including dismentaling of existing flooring
and jointed with color cement slurry including finised with flush pointing &
cleaning the surface etc. complete in Two colour pattern or as per directed
engineer incharge.(tack 10% DARK shade)
48 Providing and laying polished Kota stone slab flooring over 20mm 545.000 Sqmt 992.66
(Average) thick base of cement mortar 1:6 (1-cement : 6-coarse sand) or
L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid over and jointed with grey
cement slurry mixed with pigment to match the shade of slab including
rubbing and polishing etc. complete. (A) 25mm thick
49 Providing and laying polished kota stone slab 25mm thick in risers of 36.000 Sqmt 1187.79
steps,skirting Dedo and pillars laid on 10mm thick cement mortar 1:3 (1-
Cement : 3 coarse sand) and jointed with gray cement slury mixed with
pigment to match the shade of slab including rubbing and polishing etc.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
50 Providing and laying Antiskid G.V.T tiles 60 x 60 cm size 8 mm thick in 182.000 Sqmt 1270.58
flooring treads of steps and landing laid on a bed of 12 mm thick cement
mortar 1:3(1-cement:3-coarse sand)finishing with flush pointing in white
cement etc. completed
51 Providing and laying antiskid ceramic tiles 30 x 30 cm size 6 mm thick in 449.500 Sqmt 970.07
flooring treads of steps and landing laid on a bed of 12 mm thick cement
mortar 1:3(1-cement:3-coarse sand)finishing with flush pointing in white
52 Providing and laying glazed tiles tiles size 30 x 60 cm 8 mm thick in 1833.000 Sqmt 1441.22
skirting risers of steps and dedo on 10 mm thick cement plaster 1:3 (1-
cement:3coarse sand) and jointed with colour cement slurry etc
completed.
53 Providing and laying machine cut free edge machine polished granite 461.000 Sqmt 2575.50
stone 15mm - 18mm thick finished treads and risers in length with 1cm
projecting nozing rounded moulding in tread laid over 20 mm (av.) thick of
CM 1:6 on treads and 12mm thick CM 1:3 on risers jointed with grey or
colour cement slurry including rubbing and polishing incl. making Three
No.s of grooves of size 3mm X 3mm along the length of treads etc.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
54 Providing and fixing frosted finished 600mm x 1200mm glass urinal 77.000 Sqmt 6008.49
partition with crystalline Dhar polish on exposed edges, supported by SS
legs and fitting bracket clamp with cut holes and silicon grouting, including
all accessories and labor charges directed by the engineering in charge,
etc. complete
55 Providing and fixing mirror polished 18 mm thick Granite stone with full 2028.000 Sqmt 2936.07
round edge and polished of approved quality in clading on sill and around
the Lift door with 12 mm thick cement mortor CM (1:4) and fixing with
cement slurry & adhesive including moulding of exposed edges as
directed by engineering in charge etc. complete.
56 Providing and laying water proofing treatment by conventional method 714.000 Sqmt 942.25
including cleaning the slab surface by wire brush as directed including
provding first layer of C.M. 1:4 of 40 mm thickness mixed with water
proofing compound at rate prescribed by manufacturer, including putting of
brick bats of average thickness 40 mm Well immerssed in water laid
uniformly on first layer of mortar including applying cement slurry @ rate of
0.08 bag/sqm. on fixed layer of brick bats including maintaining necessary
slope, in second layer 40 mm thick C.M 1:4 mixed with water proofing
compound as directed, including finishing smooth with cement slurry as
directed complete.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
57 Providing and fixing M.S Safty Grills having 12mm Solid MS Squre bar 23282.000 Kg 112.11
Horizontally at every equal 0.10m C/C distance and 2 no of bar Vertically
at every equal 0.375m C/C distance Fixing on around (5x40) mm Solid MS
Patti including cutting, welding and fabrication etc; including one coat of
primer of approved quality and two coats of oil painting as per detail
drawing etc. complete as per directed Engineer in charge.
58 Providing erecting and fixing Triple layer PVC. (ISI) water tank confirm to 75000.000 Litre 9.09
IS 12701of required capacity each with all necessary fittings and
connection etc. complete on terrace.
59 Providing laying and jointing in true line and level 50mm dia. U.P.V.C. 550.000 Rmt 195.64
Pipe ( SCH- 40) for cold water including fittings as approved by Engineer
In Charge. Pipe shall be fixed on the wall with the help of clamp at every
two metre C/C or shall be concelled as directed including necessary
fittings etc. including testing of pipe and joints and fixing the same with
adhesive solvent, including cost of all materials.
60 Providing laying and jointing in true line and level 40mm dia. U.P.V.C. 560.000 Rmt 148.12
Pipe ( SCH- 40) for cold water including fittings as approved by Engineer
In Charge. Pipe shall be fixed on the wall with the help of clamp at every
two metre C/C or shall be concelled as directed including necessary
fittings etc. including testing of pipe and joints and fixing the same with
adhesive solvent, including cost of all materials.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
61 Providing laying and jointing in true line and level 25mm dia. U.P.V.C. 1020.000 Rmt 91.84
Pipe ( SCH- 40) for cold water including fittings as approved by Engineer
In Charge. Pipe shall be fixed on the wall with the help of clamp at every
two metre C/C or shall be concelled as directed including necessary
fittings etc. including testing of pipe and joints and fixing the same with
adhesive solvent, including cost of all materials.
62 Providing laying and jointing in true line and level 20mm dia. U.P.V.C. 910.000 Rmt 81.31
Pipe ( SCH- 40) for cold water including fittings as approved by Engineer
In Charge. Pipe shall be fixed on the wall with the help of clamp at every
two metre C/C or shall be concelled as directed including necessary
fittings etc. including testing of pipe and joints and fixing the same with
adhesive solvent, including cost of all materials.
63 Providing, laying and jointing in true line and level 160 diametre U.P.V.C 485.000 Rmt 831.22
(Type B) conforming to IS 13592-1992 with one end plain and other end
socketed with rubber ring, & fittings conforming to ISI 14735-1999 of
approved make for drainage system pipe line, pipe shall be jointed with
each other with rubber lubricant, pipe shall be fixed on wall using of PVC
clamp of the size 160 mm diametre x 210 mm length x 196 mm heigh at
every 2000 mm center to center or shall be concealed in walls as directed
including necessary fittings such as bends, shoes etc. including testing of
pipes and joints and jointed with adhesive solvent cement including cost of
all materials.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
64 Providing, laying and jointing in true line and level 110 diametre U.P.V.C 590.000 Rmt 835.15
(Type B) conforming to IS 13592-1992 with one end plain and other end
socketed with rubber ring, & fittings conforming to ISI 14735-1999 of
approved make for drainage system pipe line, pipe shall be jointed with
each other with rubber lubricant, pipe shall be fixed on wall using of PVC
clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at
every 2000 mm center to center or shall be concealed in walls as directed
including necessary fittings such as bends, shoes etc. including testing of
pipes and joints and jointed with adhesive solvent cement including cost of
all materials.
65 Providing, laying and jointing in true line and level 75 mm dia. UPVC 565.000 Rmt 283.81
SWRType B pipe conforming to IS 13592-1992 with one end plain and
other end socketed with rubbering and fitting conforming to ISI 14735-
1999 of approved make for drainage system pipe line, pipe shall be jointed
with each other with rubber lubricant, pipe shall be fixed on wall using of
PVC clamp at every 2000 mm c/c or shall be conceled in walss as
directed including necessary fittings such as bends, shoes etc. including
testing of pipes and joints and jointed with adhesive solvent cement
including cost of all materials.
66 Providing and fixing in PVC SWR cowel went 75mm dia to pipes.(B) 9.000 No 16.16
67 Providing and fixing in PVC SWR cowel went 110mm dia to pipes.(B) 15.000 No 29.29
110mm dia.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
68 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm 372.000 No 571.08
diameter with jali of the following nominal diameter of self cleansing
design with C.I scread down or hinged grating including the cost of cutting
and making good the walls.
69 Providing and fixing wash down water closet (European type W C pan) 36.000 No 3890.52
with integral P and S trap including jointing the trap with soil pipe in
cement mortar 1:1 (1 cement five sand) including providing and fixing
plastic seat cover for wash down WC with CP brass hinges and rubber
buffers back plastic seat with a pair of C I or MS bracket with complete
fitting such as lead valve siphon 15 mm dia brass ball valve with polythene
float CP brass handle unions and couplings for connection with inlet out let
and over flow pipes 40 mm dia porcelain enameled flush bend including
cutting holes in walls and making good the same connection the flush
bend with cistern and closet vitreous china.
70 Providing and fixing Orissa type WC pan of size 580mm x 440mm with S 34.000 No 1794.77
or P trap, including providing and fixing chromium plated brass half-turn
flush cock (25mm dia.), GI inlet and outlet connections, with all required
fitting accessories, making leak-proof joints, testing, and all labour
charges, complete as per direction of Engineer-in-Charge.
71 Providing and fixing stainless steel grab 22 cm x 60 cm on door and 5.000 No 1492.78
handicapped toilet including all fixture and accessary etc completed as per
directed engineer in charge.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
72 Providing and fixing ball cock of approved. quality as directed.(A) Copper 15.000 No 189.84
Metal (ii) 50mm dia.
73 Providing and fixing Premium Designer Ceramic Wash Basin Table Top 93.000 No 8147.67
with Slim Rim for Bathroom (18 x 13 x 5.5 Inch, White Grey, Glossy
Finish) including single hole for pillar tap, Polyamide braided connection
pipe 12mm dia-450mm length, Waste coupling (Full thread) 32mm Dia,
Waste Pipe 32mm dia, 15mm dia Angle Cock With Wall Flange Chrome
Finish, Pillar Cock High Neck Desk Mounted, and all accessories such as
bolts, nuts required for above fittings and labor charges etc. completed as
per directed engineer incharge.
74 Providing and fixing 600mm x 450mm bevelled edge mirrror of superior 89.000 No 833.73
glass mounted on 6mm thick A.C. sheet or plywood sheet and fixing to
wooden pluge with C.P. brass screws and washers.
75 Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets 72.000 No 696.90
fixed to wooden plugs with C.P. brass scews (B) 600mm x 20mm size.
76 Providing and fixing screw down bib taps of following size.(A) Brass screw 291.000 No 987.78
down bib tap crome finished polished bright. (i) 15mm dia.
77 Providing and fixing CP Angle Valve of approved make and quality, made 136.000 No 1161.50
of heavy-duty brass body with chrome plated finish, suitable for 15mm
nominal dia, including all necessary fittings, testing and making leak-proof
joints, complete as directed.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
78 Providing and fixing Urinal of approved quality including connection with 87.000 No 3530.96
trap and with integral longitudinal flush pipe.(A) Squating plate pattern
white earthenware 550mm x 300mm.
79 Providing and fixing Shop dish of approved quality including cost of all 155.000 No 580.75
accessories such as bolts, nuts required for above fittings and labor
charges etc. completed as per directed engineer incharge.
80 Providing laying and jointing in true line and level 200mm dia. Form core 340.000 Rmt 1127.16
Pipe for drainage including fittings as approved by Engineer In Charge.
Pipe shall be fixed on existing structure, Wall or ground with the help of
clamp or shall be canceled as directed including necessary fittings, etc.
including testing of pipe and joints and fixing the same with adhesive
solvent, including cost of all materials.
81 Providing and fixing S.W. gully trap with C.I. grating brick masonry 12.000 No 1246.92
chamber and water tight C.I. cover with frame of 300mm x 300mm size
(inside) with standard weight (i) Square mouth traps (B) 150mm x 100mm
size P or R type
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
82 Constructing brick masonry chamber for underground C.I. Inspection 25.000 No 3223.92
chamber and bends with briocks having croshing strength not less than
35Kg. Cm2 in C.M. 1:5 precast RCC cover 455mm x 610mm intenal
dimensions with frame (R.C.C. top slabe with 1:2:4 mix (1-cement :2-
coarse sand :4-graded stone aggregate 20mm size) foundation concrete
1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth
with a floating coat of neat cement on walls and bed concrete etc.
complete (i) Inside dimensions 455mmx 610mm and 450mm deep for
single pipe line.
83 Constructing brick masonry chamber for underground C.I. Inspection C.I. 40.000 No 3933.95
Inspection chamber and bends with briocks having croshing strength not
less than 35Kg. Cm2 in C.M. 1:5 precast RCC cover 500mmx 700mm
intenal dimensions with frame (R.C.C. top slabe with 1:2:4 mix (1-cement
:2- coarse sand :4-graded stone aggregate 20mm size) foundation
concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished
smooth with a floating coat of neat cement on walls and bed concrete etc.
complete (i) Inside dimensions 500mmx 700mm and 450mm deep for
single pipe line.
84 Extra over items for every additional depth of 0.1M. of part thereof beyond 25.000 No 242.39
450mm depth for Brick masonry chamber.(i) for 455mm x 610mm size.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
85 Extra over items for every additional depth of 0.1M. of part thereof beyond 25.000 No 264.86
450mm depth for Brick masonry chamber.(i) for 500mm x 700mm size.
86 Providing and fixing MS Ladder of required pattern with MS flats(30x3mm) 1300.000 Kg 92.92
or round or square bars (12mm) at required spacing & with round headed
bolts and nuts or screws or welding including primer coat of approved
quality and two coats of oil paintas as directed by engineer in charge
87 Constructing Kitchen Platform of 18 mm thick Polished Black Granite at 29.000 Sqmt 6183.22
top and 25 mm thick Kota stone slab one side polished at bottom with
cementing Materials / adhsives including makeing necessary grooves in
walls with Vertical sandwich two Kotastone 25 mm support every 60 cm
centre to centre or as required including all labour material of approved
quality incl. full moulded round front edge granite strip of one side
polished and jointed with grey cement slurry including rubbing and
polishing etc. complete for all floors
88 Providing and fixing 25 mm thick polished kota stone Shalve with full 84.000 Sqmt 667.61
round edge and double side polished of any required and fixing with
cement slurry & adhesive including both exposed edges cut and Smooth
Finished as directed by engineering in charge etc. complete.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
89 Providing and fixing Kitchen sink with C.I. or M.S. brackets, painted white 5.000 No. 5240.89
including cutting holes in walls and making good the same but excluding
fittings. (C) Vitreous China Sink.(i) 600mm x 450mm x 150mm size
including pillar cock 15mm, M.I fisher union 32mm, C.P Brass waste
32mm , Angle cock 15mm including all laboure and material charges etc.
completed.
90 Providing and fixing Kitchen platform trolley having three drawers of SS 29.000 Sqmt 14213.73
(IS 304) of required size like thali, katleri, perforated, partition, cupsosar
type in kitchen platform having drawer front side and backside by using
19mm thick all proof plywood of ISI quality all side laminated etc. as
directed. The size of SS (IS 304) basket of size 4" to 18" for thali, dish,
katleri, perforated, partition, cupsosar type as directed including necessary
S.S. fittings, handles, nobs, telescopic channels, etc. as directed
91 Providing and fixing 0.60 meter wide sand which type Washbasin 30.000 Sqmt 5865.07
platform including supplying and fixing granite stone of black or equivalant
quality 18 mm thick mirror polished on top and side posiition and vertical
strip at front with cement slurry & adhesive including moulding of both
exposed edges over 25 mm thick kotah stone platform fixing in top and
sides and itermediates supports fixing with cement mortar and adhesive
and finishing all material and labour with necessary fitting complete etc.
92 Providing and fixing in position 300 mm high, 150 mm wide English letters 50.000 No 1333.20
made from 1.0 mm thick stainless steel sheet as directed by Engineer in
charge with all necessary tools & plants etc. complete.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
93 Providing and fixing in position 150 mm high, English letters made from 276.000 No 686.80
1.0 mm thick stainless steel sheet as directed by Engineer in charge with
all necessary tools & plants etc. complete.
94 Providing and fixing Panel Cladding System with panels 50mm / 125mm / 64.000 Sqmt 7856.79
150mm wide and up to 3.0 m length, made of 0.50mm thick galvanized
steel or 0.65mm TCT aluminium, fixed over carrier sections with 25mm /
50mm / 75mm / 100mm gaps made of 0.60mm thick galvanized steel
stove enameled / coil coated black, including special high-quality corrosion-
resistant and super durable powder coating on both visible and rear sides,
complete with L-clit, L-angle, tubular stud section, corrosion and weather-
resistant screws and all necessary installation accessories as required for
proper structural fixing, complete
95 Providing and Fixing a set of wall mounted 38 mm dia U shaped horizontal 2.000 No 2671.45
stainless steel collapsible grab bar , 38mm vertical stainless steel fixed
grab rail of grade SS 304 from round pipe supported and 75 mm dia
mm thick SS 304 base flange on wall including anchor fasteners, nuts,
accessories as per detailed drawing etc. complete as directed by Architect
or Engineer in charge.
96 Providing and fixing MS Z clamp on Wall or celling for Pipe Fitting 729.000 No 85.85
including all type necessary fittings and accessory etc. completed as per
directed engineer in charge.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
97 Charges for making holes from 50mm to 160mm dia in RCC wall, slabs, or 144.000 No 1190.79
any other RCC members or brickwork by diamond core cutting machine of
HILTI or equivalent, including filling with approved chemical grouting,
finishing the surface, disposing of debris from all floors, complete in all
respects as directed.
98 Providing and fixing coloured self adhesive PU-Tactile tile, ground surface 15.000 Sqmt 5309.57
indicators of Polyurethane) of size 300mm x 300mm for guiding/warning to
the visually visitors in the centre/side of the pedestrian/approach pathway
as per specification and guidelines complete in all respect to the entire
satisfaction of in charge.
99 Providing and fixing acrylic multilingual Braille (raised dots) 10.000 No 1964.45
DIRECTIONAL SIGNBOARDS of size 225 x 150mm designed as per
accessibility standards and having 3.5mm thick acrylic base plate with
Upper Case San Serif words made of white acrylic non glare cut out
letters of height 15mm raised not less than 0.8mm above base plate and
the equivalent word written in Hindi with Devanagari non glare acrylic
letters of height 15mm raised not less than 0.8mm above base plate and
having a non-glare acrylic cut arrow pointing in the required direction.
Each signboard to be fixed as per manufacturers specifications on the wall
at the approved location and at a height of 1200mm from FFL complete as
per design / specifications and guidelines as per the entire satisfaction of
the Engineer-in-charge
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
100 Providing & fixing Braile indicator of size 170 mm x 35mm for handrails of 10.000 Rmt 951.42
the approved design and make have braile dots raised 0.5 mm above
base plate to be installed at specific locations as per direction of engineer
101 Providing and fixing of conspectus tape 50mm width on of treads in 50.000 Rmt 1447.33
staircase including cutting pasting etc. As per harmonised guidelines
complete in all respect to the entire satisfaction of engineer in charge.
102 Providing and Fixing 15 mm thick 300 mm x 300 mm Tactile Warning Tiles 30.000 Sqmt 1356.43
(Attention Tiles i.e. Tactile Warning Surface Indicator {TWSI}) of Johnsan
Endura Tac Button Yellow Plus or equvqlent make in flooring laid on
mm thick cement mortar 1:6 (1 cement : 6 coarse sand) on new surface
and jointed with cement slurry including finished with flush pointing &
cleaning the surface for all floors as per detailed drawing etc. complete as
directed by Architect or Engineer in charge. Thse tiles shall be Anti Skid,
Chemical Resistant, Fade Proof, Frost - Heat & Weather Proof, High
Flexural Strength, Highly Durable, Stain Resistance . All Tactile Warning
Tiles meet the specific size and dimension standards as required by
ISO/FDIS
103 Providing and laying and fixing 50 mm thick expansion joint by hydro cell 159.000 Sqmt 1491.03
semi rigid UV resistance with high performance laminated closed cell
polythene foam joint filler in sheet foam as directed, etc. complete.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
104 Applying and providing Expansion joint sealing System on 100 mm vide 159.000 Sqmt 4772.00
joint including cleaning of exansion joint by mechanical means provision of
adhesive and flexible membrane with required bond length as per
menufracturer specification and 4mm thick alluminium strip covering with
one side sloted and bolted with suitable system, inclusive of all manpower,
machinery and material as per specification and as directed.
105 Providing and filling the expansion joint by Thioflex 600 polymer or 159.000 Sqmt 515.39
equivalent confirm to BS 4254-1983 as per required shade and
manufactured specifi-cation by making groove of 50 mm x 12.5 mm lather
by cutting or by repairing groove and removing mortar drop or any other
foreign materials including applying primer and filling required size
(oversize of joint PU foam etc. complete.
106 Providing and fixing 25 cm Wide & 3mm thick exterior composite panel on 127.000 Sqmt 1054.34
existing expansion joint horizontally & vertically with all material, hardware,
acessories & fittings etc completed.
107 16mm Rebar, excluding bar. It should minimum 160mm embedded in 90.000 Nos 299.97
concrete, drill dia. Should be minimum 20mm for rebar, material should be
used Will Fischer FISV 360 or equievalent. (Pull out strength check should
be given by contractor as per technical specification)
108 12mm Rebar, excluding bar. It should minimum 120mm embedded in 90.000 Nos 199.98
concrete, drill dia. Should be minimum 16mm for rebar, material should be
used Will Fischer FISV 360 or equievalent. (Pull out strength check should
be given by contractor as per technical specification)
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
109 10mm Rebar, excluding bar. It should minimum 100mm embedded in 90.000 Nos 179.78
concrete, drill dia. Should be minimum 14mm for rebar, material should be
used Will Fischer FISV 360 or equievalent. (Pull out strength check should
be given by contractor as per technical specification)
110 8mm Rebar, excluding bar. It should minimum 100mm embedded in 90.000 Nos 163.62
concrete, drill dia. Should be minimum 14mm for rebar, material should be
used Will Fischer FISV 360 or equievalent. (Pull out strength check should
be given by contractor as per technical specification)
111 Providing, fabricating, and fixing Glass Reinforced Concrete (GRC) Railing 19.000 Sqmt 5488.34
of approved design, pattern, and profile, factory-cast using M25 grade
cement concrete with alkali-resistant (AR) glass fibre (minimum 5% by
weight of cement), fine aggregates, polymer additives, and admixtures, in
minimum 30 mm thickness (or as specified), with smooth moulded finish
free from defects or deformities, fixed in position using stainless steel (SS)
brackets, clamps, or mechanical anchors with non-shrink grout or polymer-
modified cementitious adhesive as per manufacturer’s specification,
including design approval, moulding, de-moulding, curing, transportation,
handling, scaffolding, installation, alignment, joint filling, cleaning, and
finishing, complete in all respects as per drawings and direction of
Engineer-in-Charge.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
112 Providing, fabricating, and fixing Glass Reinforced Concrete (GRC) 666.000 Sqmt 7230.59
Cornice / Patta and Cladding of approved design, profile, and pattern,
factory-cast using M25 grade cement concrete with alkali-resistant (AR)
glass fibre (minimum 5% by weight of cement), fine aggregates, polymer
additives, and admixtures, in minimum 30 mm thickness (or as specified),
with smooth moulded finish free from cracks, air pockets, or deformities,
fixed in position using stainless steel (SS) brackets, clamps, or mechanical
anchors with non-shrink grout or polymer-modified cementitious adhesive
as per manufacturer’s specification, including design approval, mould
preparation, moulding, de-moulding, curing, edge treatment,
transportation, handling, scaffolding, installation, alignment, joint filling,
cleaning, and finishing, complete in all respects as per drawings and
direction of Engineer-in-Charge.
113 Providing and fixing decorative round teakwood finial and fascia pillar at 8.000 No 51475.66
rooftop of size 0.30 m diameter and 3.70 m height, made from seasoned
first-class teakwood, machine finished with smooth surface, carved to
required profile and design, polished with exterior-grade protective
coating, and securely fixed in position with stainless steel holdfasts,
anchor bolts, and base plates, including scaffolding, handling,
transportation, erection, and finishing complete in all respects as per
drawing and direction of the Engineer-in-Charge.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
114 Providing and applying plaster embossed patta on building elevation in 1296.000 Sqmt 939.30
cement mortar 1:3 (1 cement : 3 fine sand), 30 mm thick, formed to
required profile, shape, and size as per architectural drawings, finished
smooth and true to line and level with moulded / embossed decorative
pattern, including fixing of GI chicken mesh at junctions and over
projecting portions for crack resistance, mixing with approved
waterproofing compound / polymers for better adhesion and durability,
curing, scaffolding, cutting, finishing of edges, and all labour, materials,
tools, and tackles, complete in all respects and at all heights, as directed
by the Engineer-in-Charge.
115 Extra for additional height of propping and centering where the height of 197.000 Sqmt 579.03
propping and centering exceeds 4 .O M between supporting floor to ceiling
including temporary brick or stone pillars for supporting as required. (iii)
Height more than 6.0 M. and upto 7.0 M
116 Providing and applying two or more coats of synthetic enamel paint of 1296.000 Sqmt 995.86
approved brand and shade on new plastered/concrete/wood/steel
surfaces, over one coat of appropriate primer, including surface
preparation, putty/stopping, scaffolding, curing and finishing complete, all
heights, as directed by Engineer-in-Charge.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
117 Providing and fixing wooden carving patta at sloping roof, made from 43.000 Sqmt 28842.57
teakwood of approved quality, carved with decorative pattern as per
architectural design, minimum section 0.30m width x 0.030m thick or as
specified, fixed in position with stainless steel screws, holdfasts, nails, and
adhesive as required, including cutting, shaping, finishing with smooth
surface, polishing/painting with exterior grade protective coating,
scaffolding, handling, transportation, and erection complete in all respects
as per drawing and direction of Engineer-in-charge.
118 Providing and applying black japan treatment of approved make and 1082.000 Sqmt 86.39
quality in two coats with uniform finish and complete coverage, over
prepared surface free from dust, grease, or loose particles. Surface shall
be cleaned thoroughly before application. The treatment shall be applied
with brushes only as per manufacturer's specifications and allowed to dry
between coats.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
119 Providing and fixing hollow metal door with frame made from galvanized 134.000 Sqmt 4974.16
iron (GI) sheets, ensuring stability and integrity. The door leaf shall be
to 35mm thick, double skin, fabricated from 1.2mm thick GI sheet with
honeycomb infill, and finished with powder coating in approved shade.
The frame shall be 100x50mm single rebate profile made from 1.5mm
thick GI sheet with inbuilt groove, powder coated to match. Door shall be
fitted with stainless steel hinges (4 nos. per shutter), aluminum handles,
and door magnets to retain the door in closed position. The door should
open up to 170 degrees for ease of access. All components shall be
factory prepped, field assembled, and installed complete with all
necessary hardware, accessories, and fixings as per manufacturer’s
specifications.
120 Excavation for foundation for depth from 3.0 m to 5.0 m including 35.000 Cumt 174.23
sorting out and stacking of useful materials and disposing off the
excavated stuff upto All lift and lead.(B) Dense or Hard soil
121 Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. size having 4.000 Nos 958.17
weight not less than 35Kg.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
122 Providing and fixing rolling shutters of approved make made of 80 mm 10.000 Sqmt 3503.41
wide M.S laths inter-locked together through heir entire length and jointed
together at the ends by end locks mounted on specially designed pipe
shaft with bracket plates,guide channels and arrangement for inside and
outside locking with push-pull operation including the cost of hood cover
and sprig etc.complete(A) Shutters having width below 3.5M
123 Drilling pilot borehole of size 250/300 mm at above site by mud flush direct 650.000 Rmt 573.68
rotery rig.
124 Reaming of 250/300 mm dia.Pilot borehole to size 550 mm dia. Incliding 500.000 Rmt 349.46
assembling ,lowering housing ,casing strainerpipers with gravel packing
and clayball packing etc.
125 Development of cach water bearingzone coming across the full depth of 2.000 Job 27191.22
tubewell by lowering 100 mm dia.Droplineand 32 mm dia airline for each
water bearing Zone with suitabale capacity air compressar up to avilability
of sand free discharge.
126 900 CFM /200 PSI capacity air compressar upto the availability of sand 2.000 Job 27603.30
free discharge for upto 250 mtrs
127 Supply of M.S. E.R.W. plain end medium duty pipe confirming to IS 500.000 Rmt 3605.70
4270/2001 with latest amendments Of size 250 mm dia (minmum
thicknes of 7.1 mm)
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
128 Screen Slotting of MS ERW balnce pipe with size of slot 6.75 cm X 6.35 978332.000 slots 0.24
cm X 3.12 mm for 250 mm dia pipe
129 Supply of miscellenious bore material suitable to 250 mm dia pipes as 2.000 Pair 2037.91
following (A) MS Bore clamps made from M.S. plate with 3 holes on either
side with nuts & bolts of std make of size 900X100X16 mm flat suitable for
250 mm dia pipe.
130 Supply of miscellenious bore material suitable to 250 mm dia pipes as 2.000 No 1161.62
following (B) MS Bore Plug having 100mm height made from M.S. plate
with 3 holes at equal distance on circumferrence for nut-bolts type, locking
arrrangement with nuts-bolts & lock nuts of std make complete from 5 mm
thick M.S. plate suitable for 250mm dia pipe.
131 Supply of miscellenious bore material suitable to 250 mm dia pipes as 2.000 No 1065.02
following (C) MS Bail Plug having length 0.45 mtr from medium class pipe
as per I.S. suitable for 250 mm dia pipe.
132 Supply of miscellenious bore material suitable to 250 mm dia pipes as 250.000 NO 91.71
following (D) Steel bent plate suitable for ERW pipe for 250mm dia
(size:200 X 150X6 mm)
134 Electrologging of Pilot bore hole with carting. 2.000 Job 18180.00
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
135 Geohydrological ground water investigation including vehicle charges for 2.000 No 14428.86
three phase DTH bore/DR tube well including water sample testing &
chemical analysis
136 Providing, supplying and commissioning ISI mark CI D/F Reflux Valves of 2.000 No 5401.48
following class and diameter including all taxes, insurance, transportation,
freight charges, octroi, inspection charges, loading, unloading,
conveyance to departmental stores stacking etc. complete. Reflux valves
PN 1 IS 5312 with ISI mark size: 100 mm
137 Providing and laying in trenches galvanised mild steel tubes (Midium 500.000 Rmt 919.80
grade) of the following nominal bore, and tube fitting (Earthwork in
trenches to be measured and paid for separately (H) 80mm
138 Constructing brick masonry chamber for underground C.I. Inspection 40.000 No 1246.92
chamber and bends with briocks having croshing strength not less than
35Kg. Cm2 in C.M. 1:5 precast RCC cover 455mm x 610mm intenal
dimensions with frame (R.C.C. top slabe with 1:2:4 mix (1-cement :2-
coarse sand :4-graded stone aggregate 20mm size) foundation concrete
1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth
with a floating coat of neat cement on walls and bed concrete etc.
complete (i) Inside dimensions 455mmx 455mm and 450mm deep for
single pipe line.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
139 Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2- 16.000 No 11029.97
coarse sand : 4-graded stone aggregate 20mm nominal size) foundation
concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm
size) inside plastering 15mm thick with Cement Mortar 1:3 (1-Cement : 3-
coarse sand) finished with a floating coat of neat cement and making
channels in cement concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-
stone aggregate 20mm nominal size) finished smooth complete including
curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep
including C.I. cover with frame size 560mm diameter total weight of cover
and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of
frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick
having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar
1:5 (1- Cement: 5- Coarse sand) (1) A type depth 0.90 Metre for 150mm
diameter sewer
140 Providing laying (to level or slopes) and jointing reinforced concrete Light 643.000 Rmt 665.48
duty non-pressure pipes I.S. class NP2 of the following internal diameter
with collars and butt ends prepared for collar joints including testing of
joints complete.(D) 300mm
141 Providing and fixing and floor 10.0 Kg. F/Cm2 working pressure 200.000 Rmt 336.24
poluthene pipes of the following outside Dia. Low densidy, complete with
special falnge compression type fittings, wall clipsetc. including making
good the wall ceiling and floor.(G)110 mm
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
142 Providing and fixing and floor 10.0 Kg. F/Cm2 working pressure 60.000 Rmt 696.90
poluthene pipes of the following outside Dia. Low densidy, complete with
special falnge compression type fittings, wall clipsetc. including making
good the wall ceiling and floor.(G)180 mm
143 Providing junction for rain water juncton chamber of size 0.60x0.60x0.75m 20.000 Nos. 9357.65
with excavation of size 1.96x1.96 m & 0.15m thick c.c.1:2:4 bed concrete
including brick masonary wall in CM 1:6 of 0.75m height & 0.23m thick
with 15mm thick cement plaster inside & outside & 1.06x1.06 RCC (1:2:4)
slab of thickness 0.15m with CRS steel and 0.60mx0.45m cast iron
manhole cover with frame weight not less than 35 kg as per directed by
Engineer-in-charge
144 Providing and installation Recharge pit of “RAIWOHA” Make 3 layer RCC 2.000 Nos. 109645.60
Precast Injection well system of size 1.5 meter Dia. X 3.4 Meter Height
rein forced concrete precast three layer module with 6” dia x 12” dia. V
wire screen of 0.75mm x 1.0 mm Slot size in SS 304 material and
meter height with MS Top cover and required Air vent including all
necessary excavation and transportation at site including required filter
media for the recharge system as per site requirement.
145 Supplying slotted PVC pipes of approved quality at site of work confirming 150.000 Rmt 555.50
to IS. 1239/1974 180mm dia.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
146 Cleaning & maintenance of system Including all Labour and replacing of 2.000 Nos. 4646.00
Filter Media as Required for one year
147 Construction of granular sub-base 150 mm thick by providing coarse 860.000 Cum 1705.89
graded machine crushed B.T. material satisfying MOST specification of
grading I (B.T. stone aggregate 53 mm to 26.5 mm 35 %, 26.5 to 4.75 mm
- 45 % and 2.36 mm below - 20 % )including spreading in uniform layer
with motor grader on prepared surface, mixing by mix in place method
with rotavator at OMC and compacting with vibratory roller to achieve the
desired density etc. complete.
148 Steel work, welded in built up sections framed work including cutting, 25550.000 kg 84.13
hoisting, fixing in position and applying a priming coat of read lead paint &
two coat oil paint. (A)In beams and joists, channels angles Tees, flats,
with connecting plates or angle cleats as in main and cross beams. Hip
and jack rafters, purlins conneted to common rafters and the like..
149 Providing and fixing of Ridge flashing for roof panel shall be made out of 882.000 Sqmt 858.67
0.5 mm thick pre coated GI sheet . The Precoated sheet shall be of
minimum 240 mpa steel grade confirming to IS 14246:1995 and shall have
zinc coating of minimum 120 gsm as per IS:277:1992 , 5-7 microns epoxy
primer on both side of the sheet and polyester top coat 15-18 micron. The
PPGI Sheet shall have plastic protective guard film of minimum
microns to avoid scratches during transportation. The ridge shall be fixed
to the steel members by pop rivet or self drilling/self stitching fastners @
maximum 450 mm c/c along length of capping/flashing etc complete .
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
150 Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete 1436.000 Sqm 686.90
block 60mm thick with grade of concrete M300 pnumatic compressed /
vibrated mechanically and as per approved design Confirming to IS
: 2006 including 35 mm Sand layer for levelling and filling the joint with
sand in proper line and level as per guidlines of IRC : SP 63-2018 etc.
151 Providing and fixing pre-cast concrete kerb stone of gray cement based 934.000 Rmt 361.64
concrete block 30cm ength,30cm height and 15cm thick of M250 grade
concret as per approved design and including excavation for fixing in
proper line and level,filling the joint with C:M 1:3 (1cement:3fine sand) etc
152 Box cutting the road surface to proper slope and camber for making a 2015.000 Cum. 102.93
base for road work including removing the excavated stuff and depositing
on the road side slope as directed upto upto All lift and lead..
153 Providing, laying and compacting natural sand & gravel[ C.B.R. not less 287.000 Cum. 383.80
than 20%] below sub base course including carriage of materials
spreading in uniform layer manually on prepared base and compacted
with vibratory roller to achieve desired density including all materials,
labour etc. complete.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
154 Compaction and finishing of cement concrete road by trimix process 2862.000 Sqm 63.63
providing extra Labour charges for the trimix vacume dewatering service
process on cement concrete road sutface by using vacuum dewatering
pump floater surface vibrator including making groves and rough finish to
surface including leveling etc complete.
155 Constructing providing and fabricating cattle guard using channel section 11.000 Sqmt 4930.82
frame of size ISMC series 100 mm x 50 mm (Weight 9.20 kg/Rmt) and
ISMC section 100 mm x 75mm (weight 11.50 kg/Rmt) intermediate
support for welding G.I.pipe at 12 Cm C/C of size 50 mm in a frame made
of Channel section size 100 mm x 50 mm all round including fixing the unit
on prepared chamber of masonary wall using MS hold fast embeded in
masonary wall top as directed by Engineer in charge and as per drawing
and necessary required arrangement etc complete.
156 Providing and fixing decorative entrance gate made out of cast iron and 1733.000 kg 161.60
various mild steel tabular section combination , the Ornamental entrance
gate should be fixed at compound wall including pattern and die making
cutting , welding , grinding, fabrication , fixing in position at compound wall
with necessary pedestal, bearing block and other locking arrangement.
The entrance gate should be painted with two coats of priming coat of
paint, and two coat of oil paint etc complete. As per detail design and
instruction of architect.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
157 Providing and fixing concertina coil fencing with punched tape concertina 740.000 Rmt 1215.03
coil 600 mm dia 10 mt openable length having 50 no rounds per 6 mt
length, upto 3mt height of wall with existing angle iron (50mm x50mm
x5mm )requird shaped As per Directed Engeenier in charge. placed 2.4mt
or 3.00mt apart and with 4 horizontal R.B.T. reinforced barbed wire(3 mm)
, stud tied with G.I. staples and G.I. clips to retain horizontal, including
necessary bolts or G.I.barbed wire tied to angle iron, all complete as per
direction of Engineer-in-charge, with reinforced barbed tape
(R.B.T.)/Spring core (2.5 mm thick) and weight 43.478 gm/meter at
compound wall for ESR M4/ intakewell.
158 Supply. installation, testing & commissioning of ISI approved electrical 1.000 No 98432.21
motor driven jockey pump set having 10.8 m3/hr. @ 70m head. The pump
unit shall be a horizontally direct mounted motor. Unit shall comprise the
following minimum requirements: a) Pump, b) Electric motor IE2, c)
Foundation bolts, d) Mating flanges with gasket and fasteners, e)
Discharge gauges, etc. complete in all respect, with labour.
159 Supply, installation, testing & commissioning of Priming tank, HDPE type, 1.000 No 25677.97
1000 litres, with necessary piping 100 mm size, G.I pipe for priming the
pumps, pipe of with butterfly valves for isolation, Water Filling to priming
tank by piping min. 50 mm size, with all complete.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
160 Supply, installation, testing & commissioning of Manifold( surge vessel,)for 1.000 No 55635.60
fire hydrant system, min. 300 mm diameter, made from M.S plate, hydro
tested to 15 kg./cm2. with ball valves, header with couplings for fitting
pressure switches, pressure gauges etc.with necessary isolation valves
with all complete.
161 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW piping, 540.000 Mtr 398.01
conforming to IS:1239, part-I, Heavy class up to 150 mm dia. and IS:3589,
for size 200 mm dia. & above, thickness. G.I. pipe fitting's as per IS:
1239, part-II, Heavy class for size 150 mm dia. & below & IS: 3589, for
size 200 mm dia. above, flanges, nuts bolts & washers, 3 mm thick
gasket, pipe hangers, etc.
Hydrostatic testing for 2 hour's at 150% of the system pressure, hook-up
Painting for piping, fittings & structural pipe support, shall be two coat of
zinc primer and two coats of fire red conf. to IS: 5, Shade 536. Complete
with all accessories as per approved drawings, specicification and
direction of the Engineer-in-Charge, with all complete. 25 mm dia.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
162 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW piping, 250.000 Mtr 641.95
conforming to IS:1239, part-I, Heavy class up to 150 mm dia. and IS:3589,
for size 200 mm dia. & above, thickness. G.I. pipe fitting's as per IS:
1239, part-II, Heavy class for size 150 mm dia. & below & IS: 3589, for
size 200 mm dia. above, flanges, nuts bolts & washers, 3 mm thick
gasket, pipe hangers, etc.
Hydrostatic testing for 2 hour's at 150% of the system pressure, hook-up
Painting for piping, fittings & structural pipe support, shall be two coat of
zinc primer and two coats of fire red conf. to IS: 5, Shade 536. Complete
with all accessories as per approved drawings, specicification and
direction of the Engineer-in-Charge, with all complete. 50 mm dia.
163 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW 200.000 Mtr 1176.90
piping, conforming to IS:1239, part-I, Heavy class up to 150 mm dia. and
IS:3589, for size 200 mm dia. & above, thickness. G.I. pipe fitting's as per
IS: 1239, part-II, Heavy class for size 150 mm dia. & below & IS: 3589, for
size 200 mm dia. above, flanges, nuts bolts & washers, 3 mm thick
gasket, pipe hangers, etc.
Hydrostatic testing for 2 hour's at 150% of the system pressure, hook-up
Painting for piping, fittings & structural pipe support, shall be two coat of
zinc primer and two coats of fire red conf. to IS: 5, Shade 536. Complete
with all accessories as per approved drawings, specicification and
direction of the Engineer-in-Charge, with all complete. 80 mm dia.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
164 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW piping, 175.000 Mtr 1690.47
conforming to IS:1239, part-I, Heavy class up to 150 mm dia. and IS:3589,
for size 200 mm dia. & above, thickness. G.I. pipe fitting's as per IS:
1239, part-II, Heavy class for size 150 mm dia. & below & IS: 3589, for
size 200 mm dia. above, flanges, nuts bolts & washers, 3 mm thick
gasket, pipe hangers, etc.
Hydrostatic testing for 2 hour's at 150% of the system pressure, hook-up
Painting for piping, fittings & structural pipe support, shall be two coat of
zinc primer and two coats of fire red conf. to IS: 5, Shade 536. Complete
with all accessories as per approved drawings, specicification and
direction of the Engineer-in-Charge, with all complete. 100 mm dia.
165 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW piping, 200.000 Mtr 2525.00
conforming to IS:1239, part-I, Heavy class up to 150 mm dia. and IS:3589,
for size 200 mm dia. & above, thickness. G.I. pipe fitting's as per IS:
1239, part-II, Heavy class for size 150 mm dia. & below & IS: 3589, for
size 200 mm dia. above, flanges, nuts bolts & washers, 3 mm thick
gasket, pipe hangers, etc.
Hydrostatic testing for 2 hour's at 150% of the system pressure, hook-up
Painting for piping, fittings & structural pipe support, shall be two coat of
zinc primer and two coats of fire red conf. to IS: 5, Shade 536. Complete
with all accessories as per approved drawings, specicification and
direction of the Engineer-in-Charge, with all complete. 150 mm dia.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
166 Supply, fabrication & erection of aboveground G.I. 'C'-Class, ERW piping, 100.000 Mtr 3423.73
conforming to IS:1239, part-I, Heavy class up to 150 mm dia. and IS:3589,
for size 200 mm dia. & above, thickness. G.I. pipe fitting's as per IS:
1239, part-II, Heavy class for size 150 mm dia. & below & IS: 3589, for
size 200 mm dia. above, flanges, nuts bolts & washers, 3 mm thick
gasket, pipe hangers, etc.
Hydrostatic testing for 2 hour's at 150% of the system pressure, hook-up
Painting for piping, fittings & structural pipe support, shall be two coat of
zinc primer and two coats of fire red conf. to IS: 5, Shade 536. Complete
with all accessories as per approved drawings, specicification and
direction of the Engineer-in-Charge, with all complete. 200 mm dia.
167 Supply, installtion, testing & commissioing of Underground GI (ERW) 50.000 Mtr 2020.00
piping conforming to IS:1239, part-I, Heavy class ('C' class) up to 150 mm
dia. and IS:3589 Heavy class ('C' class), for 200 mm dia. & above, min.
6.35mm thickness including Heavy class fittings, anti-corrosive tape of
size 150 mm wide x 4 mm thick, wrapping & coating with 13KV holiday
testing . Rates shall include sand bedding of 75mm dia all around,
backfilling of the excavated including installation of heavy pipe fitting's,
flanges, etc. 10 % of all the welded joints shall be done radiographically
tested and 50% of the joints radiographed shall be the "Field Joints".
Hydrostatic testing for 2 hours at 150% of the system pressure, hook-up
etc., complete with all accessories as per approved drawings,
specicification and direction of the Engineer-in-Charge, with all complete.
(Road Crossing) 100 mm dia.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
168 Supply, installtion, testing & commissioing of Underground GI (ERW) 50.000 Mtr 3047.12
piping conforming to IS:1239, part-I, Heavy class ('C' class) up to 150 mm
dia. and IS:3589 Heavy class ('C' class), for 200 mm dia. & above, min.
6.35mm thickness including Heavy class fittings, anti-corrosive tape of
size 150 mm wide x 4 mm thick, wrapping & coating with 13KV holiday
testing . Rates shall include sand bedding of 75mm dia all around,
backfilling of the excavated including installation of heavy pipe fitting's,
flanges, etc. 10 % of all the welded joints shall be done radiographically
tested and 50% of the joints radiographed shall be the "Field Joints".
Hydrostatic testing for 2 hours at 150% of the system pressure, hook-up
etc., complete with all accessories as per approved drawings,
specicification and direction of the Engineer-in-Charge, with all complete.
(Road Crossing) 150 mm dia.
169 Design , Supply and installation of Safety Signage made of Zinc Sulphilde 13500.000 Sq. inch 9.41
based glow in dark , Rigid sheet with High Luminous property enclosed in
a transperent weather proof UV stabilized plastic pasted on 3 mm thick
clear acrylic sheet such as EXITS, EMERGENCY EXIT, DO NOT USE
LIFT DURING FIRE, FLOOR MARKINGS, FIRE LIFT, STAIRCASE EXIT,
FIRE ALARM CALL POINT, FIRE HOSE REEL, FIRE HYDRANT POINT
170 Supply, Installtion, Testing & Commissioing of Standard Response 450.000 No 556.36
Sprinkler, Pendent Brass Sprinkler, Quartzoid Bulb type with crome finish,
nickel crome platde, K factor K-80, Temp.- 680C, 1/2" end connection
including resessed escutcheon. (UL Listed).
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
171 Supply, installation, testing & commissioning of pressure switch. (Range 0 4.000 No 2824.58
172 Supply, installation, testing & commissioning of 150 mm dia. dial Burdon 9.000 No 2738.98
Type Glycerine Filled pressure gauge with isolation ball valve
arrangements with necessary isolation valves with all complete.( Range
173 Supply, installation, testing & commissioning of Cast iron body double 4.000 No 5905.93
flanged gate valve With Rising Spinldle conf. to IS: 14846, PN-1.6 with
mating flanges, drilling as per IS/ANSI 150# with mating flanges,
galvanized nut, bolts & washers, gasket 3 mm thick, etc., with all
complete. 50 mm dia.
174 Supply, installation, testing & commissioning of Cast iron body double 1.000 No 8182.71
flanged gate valve With Rising Spinldle conf. to IS: 14846, PN-1.6 with
mating flanges, drilling as per IS/ANSI 150# with mating flanges,
galvanized nut, bolts & washers, gasket 3 mm thick, etc., with all
complete. 80 mm dia.
175 Supply, installation, testing & commissioning of Cast iron body double 2.000 No 10271.18
flanged gate valve With Rising Spinldle conf. to IS: 14846, PN-1.6 with
mating flanges, drilling as per IS/ANSI 150# with mating flanges,
galvanized nut, bolts & washers, gasket 3 mm thick, etc., with all
complete. 100 mm dia.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
176 Supply, installation, testing & commissioning of Cast iron body double 1.000 No 15920.34
flanged gate valve With Rising Spinldle conf. to IS: 14846, PN-1.6 with
mating flanges, drilling as per IS/ANSI 150# with mating flanges,
galvanized nut, bolts & washers, gasket 3 mm thick, etc., with all
complete. 150 mm dia.
177 Supply, Installation, Testing & Commissioning of Cast iron body Butterfly 9.000 No 2011.45
valve according to IS: 13095, PN-1.6, Iron Disc for size 150 mm dia. &
below Lever operated and above 150 mm dia. Gear operated complete
with mating flanges /ANSI class # 150 with bolts & nuts washers, rubber
gaskets 3 mm thick, etc., with all complete. 50 mm dia.
178 Supply, Installation, Testing & Commissioning of Cast iron body Butterfly 2.000 No 2567.80
valve according to IS: 13095, PN-1.6, Iron Disc for size 150 mm dia. &
below Lever operated and above 150 mm dia. Gear operated complete
with mating flanges /ANSI class # 150 with bolts & nuts washers, rubber
gaskets 3 mm thick, etc., with all complete. 80 mm dia.
179 Supply, Installation, Testing & Commissioning of Cast iron body Butterfly 4.000 No 3124.15
valve according to IS: 13095, PN-1.6, Iron Disc for size 150 mm dia. &
below Lever operated and above 150 mm dia. Gear operated complete
with mating flanges /ANSI class # 150 with bolts & nuts washers, rubber
gaskets 3 mm thick, etc., with all complete. 100 mm dia.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
180 Supply, Installation, Testing & Commissioning of Cast iron body Butterfly 2.000 No 4493.65
valve according to IS: 13095, PN-1.6, Iron Disc for size 150 mm dia. &
below Lever operated and above 150 mm dia. Gear operated complete
with mating flanges /ANSI class # 150 with bolts & nuts washers, rubber
gaskets 3 mm thick, etc., with all complete. 150 mm dia.
181 Supply, installation, testing & commissioning of Cast iron body Dual Plate 1.000 No 1540.67
Wafer Type NRV conf. to IS: 210, PN-1.6 complete with mating Flanges
class # 150 with bolts & nuts, washers, gaskets 3 mm thick, etc., with all
complete Accessories 50 mm dia.
182 Supply, installation, testing & commissioning of Cast iron body Dual Plate 1.000 No 2225.42
Wafer Type NRV conf. to IS: 210, PN-1.6 complete with mating Flanges
class # 150 with bolts & nuts, washers, gaskets 3 mm thick, etc., with all
complete Accessories 80 mm dia.
183 Supply, installation, testing & commissioning of Cast iron body Dual Plate 2.000 No 3166.96
Wafer Type NRV conf. to IS: 210, PN-1.6 complete with mating Flanges
class # 150 with bolts & nuts, washers, gaskets 3 mm thick, etc., with all
complete Accessories 100 mm dia.
184 Supply, installation, testing & commissioning of Cast iron body Dual Plate 1.000 No 5820.34
Wafer Type NRV conf. to IS: 210, PN-1.6 complete with mating Flanges
class # 150 with bolts & nuts, washers, gaskets 3 mm thick, etc., with all
complete Accessories 150 mm dia.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
185 Supply, installation, testing & commissioning of SG iron body SinglePlate 1.000 No 1112.71
Wafer Type NRV conf. to ASTMA 536, PN-1.6 complete with mating
Flanges class # 150 with bolts & nuts, washers, gaskets 3 mm thick, etc.,
with all complete. Accessories 50 mm dia.
186 Supply, installation, testing & commissioning of SG iron body SinglePlate 1.000 No 1455.09
Wafer Type NRV conf. to ASTMA 536, PN-1.6 complete with mating
Flanges class # 150 with bolts & nuts, washers, gaskets 3 mm thick, etc.,
with all complete. Accessories 80 mm dia.
187 Supply, installation, testing & commissioning of SG iron body SinglePlate 1.000 No 1797.46
Wafer Type NRV conf. to ASTMA 536, PN-1.6 complete with mating
Flanges class # 150 with bolts & nuts, washers, gaskets 3 mm thick, etc.,
with all complete. Accessories 100 mm dia.
188 Supply, installation, testing & commissioning of Y Type Strainer complete 1.000 No 5563.55
with mating flanges with bolts & nuts, washers, gaskets 3 mm thick, etc.,
with all complete accessories. 80 mm dia.
189 Supply, installation, testing & commissioning of Y Type Strainer complete 1.000 No 7275.42
with mating flanges with bolts & nuts, washers, gaskets 3 mm thick, etc.,
with all complete accessories. 100 mm dia.
190 Supply, installation, testing & commissioning of Y Type Strainer complete 2.000 No 11555.09
with mating flanges with bolts & nuts, washers, gaskets 3 mm thick, etc.,
with all complete accessories. 150 mm dia.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
191 Supply, installing, testing and commissioning of Normax make CI heavy 1.000 No 4194.07
duty ball type foot valve with flanges, nut bolts, gaskets etc. with
necessary complete accessories. 80 mm dia.
192 Supply, installing, testing and commissioning of Normax make CI heavy 1.000 No 6162.71
duty ball type foot valve with flanges, nut bolts, gaskets etc. with
necessary complete accessories. 100 mm dia.
193 Supply, installing, testing and commissioning of Normax make CI heavy 1.000 No 12411.02
duty ball type foot valve with flanges, nut bolts, gaskets etc. with
necessary complete accessories. 150 mm dia.
194 Supply, installation, testing & commissioning of Four way fire brigade Inlet 1.000 No 8987.29
connection with 63 mm dia. stainless steel (SS304) instantaneous male
inlets with built in non return valve in each inlet with 150 mm dia. header
pipe, suitable rubber cap and GI chain including nuts, bolts, washers,
gasket 3 mm thick, etc. with all complete.
195 Supply, installation, testing & commissioning of Two way fire brigade Inlet 1.000 No 5135.60
connection with 63 mm dia. stainless steel (SS304) instantaneous male
inlets with built in non return valve in each inlet with 100 mm dia. header
pipe, suitable rubber cap and GI chain including nuts, bolts, washers,
gasket 3 mm thick, etc. with all complete.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
196 Supplying FIRE bucket round bottom of 9 liters capacity made out of 24 9.000 No 1027.12
gauge G.I Sheet with extra handle at bottom duly painted white inside and
Red out side with FIRE mark. Filled with dry-sand and kept on existing
stand provided or hung on wall hook.
197 Supplying and erecting floor mounting Stand for keeping four nos. of FIRE 2.000 No 5563.56
buckets comprising 1500 mm in length, 900 mm height frame made out of
30mm x 30 mm x 4 mm angle iron with cross supports legs, welded with
hooks and duly painted with one coat of primer and two coats of approved
enamel P O red paint.
198 Supply & installation of stainless steel body Orifice Plate of suitable inner 18.000 No 1069.91
bore along with matching flange - as per specification & requirement as
per hydraulic calculation.
199 Providing and fixing approved make Perforated C type cable tray. Made 20.000 Mtr 471.67
from pre- galvanized sheet steel. The cable tray should be bended as per
IS 2062/1079 . with max 17.5% perforation with coupler plate / Fish plate
and GI hardware like nut - bolt and washers etc. erected on existing
support as per Specification and as per instruction of engineer in
charge..(5) 300 X 50 X 1.5 mm Thick
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
200 Providing and fixing approved make Perforated C type cable tray. Made 20.000 Mtr 322.19
from pre- galvanized sheet steel. The cable tray should be bended as per
IS 2062/1079 . with max 17.5% perforation with coupler plate / Fish plate
and GI hardware like nut - bolt and washers etc. erected on existing
support as per Specification and as per instruction of engineer in
charge..(3) 150 X 50 X 1.5 mm Thick
201 Supply, installation, testing & commissioning of Oblique pattern type 18.000 No 5435.17
stainless steel (SS 304) single headed External Fire Hydrant Valve with
mm dia. female instantaneous outlet conf. to IS: 5290, type - A, including
mating flanges, galvanised nuts, galvanised bolts/studs, washers &
gaskets 3 mm thick with all complete.
202 Supply, installation, testing & commissioning of 63 mm dia. stainless steel 18.000 No 1754.66
(SS 304) Universal Branch Pipe conf. to IS:
203 Supply & installation, testing & commissioing of Fire Fighting Hose - conf. 18.000 No 6967.29
to IS : 636, type B (type- 3), The fire hose shall be 15 m long with 63 mm
dia. stainless steel (SS 304) couplings conf. to IS: 903, at both the ends
for connection with the hydrant valve and the branch pipe.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
204 Supply, installation, testing & commissioning of fabricated from 3 mm MS 18.000 No 2525.00
sheet, hose box of size-450 mm x 600 mm x 250 mm - painted with Fire
Red as per IS: 5, shade no. 536 front 3 mm thick transparent glass with
lock & key, handle and brass hinges - to accommodate one number of
mtr long hose and one number of universal branch pipe, including
supporting arrangement with civil work.
205 Supply, Installation, testing & commissioing of Swinging type mild steel 18.000 No 7403.82
hose reel drum with 20 mm dia. x 30 mtr. rubber hose as per IS: 884. The
mounting stand shall be of mild steel and the hose shall be fitted with a SS
shut-off nozzle & SS ball valve of 25 mm dia. including supporting
arrangement with all complete. accessories
206 Supplying, fixing & testing of of CI ball Valve 25mm dia. (Thread) 40.000 No 706.14
207 Supplying, fixing & testing of New Battery of diesel engine 150 Amp. 1.000 No 15834.75
208 Supply and installation of Diesel Tank For Diesel Engine With All 1.000 No 16690.67
Accessories 100 Ltrs.
209 Supplying, filling & testing lube oil for diesel engine 20.000 Ltrs 320.98
210 Supply and commissioning of Oil Filter. 1.000 No 706.14
211 Supplying, filling of diesel in diesel engine tank 75.000 Ltrs 89.87
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
212 Supply and commissioning of Diesel Filter 1.000 No 427.97
213 Supplying, filling & testing coolant to engine cooling for radiator 20.000 Ltrs 239.66
214 Filling Of Gaps Between pipe and Core Cutting Hole With Chemical and 38.000 No 299.58
215 Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 25.000 Mtr 136.35
1.1 KV grade to be erected as directed of following size. (E) 3 core
Sq. mm for pressure switch
216 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable 35.000 Mtr 285.83
multistrand Copper conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe at road crossing or floor of
following size of cable. (Only Fire Panel to Fire Pump) (B) 3 core 4 Sq.
217 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable 40.000 Mtr 497.93
multistrand Copper conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe at road crossing or floor of
following size of cable. (Only Fire Panel to Fire Pump) (D) 3 core 10 Sq.
mm (Only Fire Panel to Fire Pump)
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
218 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable 45.000 Mtr 213.11
multistrand Copper conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe at road crossing or floor of
following size of cable for Diesel Engine Battery Charger (A) 3 core 2.5Sq.
219 Supply, Filling and Fixing of approved make ABC type fire extinguisher - 36.000 No 1968.64
6 Kg. Capacity as per IS:15683 & IS :
220 Supply, Filling and Fixing of approved make CO2 type fire extinguisher. 36.000 No 5520.76
Capacity 4.5 Kg. (conforming to IS-15683).
221 Supply, Filling and Fixing of approved make ABC Moduler type automatic 36.000 No 3423.73
fire extinguisher. Capacity 5 Kg. (conforming to IS-15683).
222 Submitting the application to obtain Fire Plan Approval and After 1.000 No 151500.00
Completion of Work Obtain Final Fire NOC for 3 Year.
223 Supply, Installation and commissioning of Air Release Valve, 25 mm Dia. 2.000 No 1412.29
connection.
224 Supply, Installation and commissioning of Fire Alarm Panel Conventional 1.000 No 35350.00
type, 8 zone, with complete accessories.
225 Supply, Installation and commissioning of smoke detectors / heat 180.000 No 1027.12
detectors, with complete accessories.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
226 Supply, Installation and commissioning of plug in base for the smoke 100.000 No 256.78
detectors, hooters, with complete accessories.
227 Supply, Installation and commissioning of Audio hooters , with complete 10.000 No 1069.91
accessories.
228 Supply, Installation and commissioning of Manual Call Points, with 10.000 No 1010.00
complete accessories.
229 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable 450.000 Mtr 176.75
multistrand Copper conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe of following size of cables
(A) 2 core 2.5 Sq. mm for Fire Alarm System
230 Core cutting in wall and in RCC slab with size as below: 50 mm dia. Hole 12.000 No 342.37
231 Core cutting in wall and in RCC slab with size as below: 80 mm dia. Hole 2.000 No 427.97
232 Core cutting in wall and in RCC slab with size as below: 100 mm dia. Hole 4.000 No 513.56
233 Core cutting in wall and in RCC slab with size as below: 150 mm dia. Hole 8.000 No 599.15
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
234 Core cutting in wall and in RCC slab with size as below: 200 mm dia. Hole 10.000 No 855.93
235 Supply, installation, testing & commissioning of ISI approved electrical 1.000 Set 204995.76
motor operated Kirloskar make fire hydrant main pump set horizontal end
suction back pull out top discharge centrifugal fire pump set with all the
standard acessories, base frame, coupling, and foundation bolts with
following specifications
Model -DB 80/26,
Flow-137 m3/hr,
Head-70 meter,
Motor Rating -45KW/60HP/3 ph
Suc x Del - 100 x
236 Supplying, installing, testing and commissioning of Kirloskar make diesel 1.000 Set 447652.54
engine driven fire hydrant pump set, suitable for automatic operation and
consisting of horizontal type centrifugal end suction back pull-out, top
discharge pump with cast iron body and bronze impeller, mounted on M.S.
fabricated common base plate with coupling, coupling guard, foundation
bolts and all necessary accessories, complete as required. The pump shall
be of Model KFE, having a discharge capacity of 137 m³/hr at 70 meters
head, driven by a 62 HP diesel engine, 3 phase, with suction and delivery
size of 125 mm x 100 mm.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
237 Fire Hydrant Panel suitable for 10 HP Jockey Pump, 60 HP (137 m³/hr @ 1.000 No 141400.00
70 m head) Main Electrical Pump and 62 HP (137 m³/hr @ 70 m head)
Diesel Engine Operated Pump, consisting of Incomer with MCCB (1 No.),
R Y B Indication (1 Set) and VAF Digital Meter (1 Set); Outgoing with F1 –
60 HP Star Delta Starter for Main Pump, F2 – 10 HP DOL Starter for
Jockey Pump, F3 – Auto On/Off Diesel Pump with Battery Charger,
Control Circuit with Auto/Manual On/Off, On/Off Trip Indication and On/Off
Push Button; Fabrication duly powder coated in PO Red Colour, fabricated
from 14/16 SWG GI Sheet with IP-42 Protection, fixed type floor mounted
with bottom cable entry, complete as required.
238 Pay Legal Fees to Concern Authority for Obtaining Plan Approval and 8870.510 Sq.mt 15.15
Total : A
239 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm 1508.000 Pts 485.81
(Green) both are of ISI marked 1.1 KV grade FRLSH PVC insulated multi
strand copper wires up to 10 mtr length , in below type of pipe erected
with 6A Modular type switch / bell push & accessories and earth continuity
of following type, erected on PVC / Metallic/Wooden box, single mounting
base frame covered with textured/metallic/white front plate modules
erected on / in wall / ceiling as per pipe erected, with necessary Lamp
holder/ceiling rose / H.D.Connector as directed.(f) with medium class Rigid
PVC pipe and accessories erected concealed in wall/ceiling complete.Cat-
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
240 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) 653.000 Pts 674.68
both are of .ISI marked 1.1 KV Grade FRLSH PVC insulated multi strand
copper wires up to 10 mtr length, in below type of pipe erected with 6A
Modular type switch and hum free EME step type electronic fan regulator
mounted and accessories with earth continuity of following type erected
on PVC / Metallic/Wooden box, single mounting base frame covered with
textured/metallic/white front plate modules erected on / in wall / ceiling as
per pipe erected. with necessary ceiling rose / H.D.Connector as
directed..(f) with medium class Rigid PVC pipe and accessories erected
concealed in wall/ceiling complete.Cat-III
241 Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin 521.000 Pts 257.55
socket erected on PVC / Metallic/Wooden box, single mounting base
frame covered with textured / metallic/white front plate modules erected
on / in wall / ceiling with following type accessories.Cat-III
242 Providing following type of Modular Type Accessories mounted with PVC / 295.000 Ea 151.50
metallic/Wooden box, single mounting base frame covered with textured /
metallic/white front plate , modules erected with necessary connections
as per site situation directed by Engineer In charge. (1)One No. SP 6 Amp
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
243 Providing following type of Modular Type Accessories mounted with PVC / 295.000 Ea 151.50
metallic/Wooden box, single mounting base frame covered with textured /
metallic/white front plate , modules erected with necessary connections
as per site situation directed by Engineer In charge. (2) One No 5 pin plug
244 Providing following type of Modular Type Accessories mounted with PVC / 69.000 Ea 180.79
metallic/Wooden box, single mounting base frame covered with textured /
metallic/white front plate , modules erected with necessary connections
as per site situation directed by Engineer In charge. (9) 16 Amp. SP one
way switch
245 Providing following type of Modular Type Accessories mounted with PVC / 69.000 Ea 199.98
metallic/Wooden box, single mounting base frame covered with textured /
metallic/white front plate , modules erected with necessary connections
as per site situation directed by Engineer In charge. (10) 6/16Amp.
Universal socket
246 Providing following type of Modular Type Accessories mounted with PVC / 2.000 Ea 160.59
metallic/Wooden box, single mounting base frame covered with textured /
metallic/white front plate , modules erected with necessary connections
as per site situation directed by Engineer In charge. (3) Two Pin/RJ-11
Telephone Socket[A] For One Gang Cat.III
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
247 Providing following type of Modular Type Accessories mounted with PVC / 2.000 Ea 160.59
metallic/Wooden box, single mounting base frame covered with textured /
metallic/white front plate , modules erected with necessary connections
as per site situation directed by Engineer In charge. (4) TV Co-axial
Socket outlet Cat-III
248 Providing following type of Modular Type Accessories mounted with PVC / 350.000 Ea 25.25
metallic/Wooden box, single mounting base frame covered with textured /
metallic/white front plate , modules erected with necessary connections
as per site situation directed by Engineer In charge. (7) Blank Plate Single
249 Providing following type of Modular Type Accessories mounted with PVC / 38.000 Ea 160.59
metallic/Wooden box, single mounting base frame covered with textured /
metallic/white front plate , modules erected with necessary connections
as per site situation directed by Engineer In charge. (8) Computer RJ-45
socket Cat-III
250 Providing following type of Modular Type Accessories mounted with PVC / 29.000 Ea 410.06
metallic/Wooden box, single mounting base frame covered with textured /
metallic/white front plate , modules erected with necessary connections
as per site situation directed by Engineer In charge. (14) 6A/ 10A/ 16A/
20A/ 25A/ 32A Double Pole Modular MCB Switch Cat-III
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
251 Providing and erecting ISI mark Medium class RIGID PVC PIPES of 1400.000 Mtr. 33.33
following size complete to be erected on/in wall or ceiling erected with
necessary PVC fittings & Junction boxes fixed with adhesive solution &
Clamps with following dia of pipes, in approved manner as directed (b)
252 Providing and erecting ISI mark Medium class RIGID PVC PIPES of 150.000 Mtr. 54.54
following size complete to be erected on/in wall or ceiling erected with
necessary PVC fittings & Junction boxes fixed with adhesive solution &
Clamps with following dia of pipes, in approved manner as directed (c)
253 Providing & erecting PVC Corrugated Flexible Conduit with required nos. 200.000 Mtr. 21.21
of coupling, PVC bushes, Check-nuts etc. complete of following sizes.(2)
254 Providing & erecting PVC Corrugated Flexible Conduit with required nos. 50.000 Mtr. 27.27
of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (3)
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
255 Supplying under floor pregalvanised corrosion proof rectangular sheet 180.000 Mtr. 1224.12
steel cable trunking of 1.6 mm thick having with stand point load up to
1.33 Ton & free from seepage of concrete of screed water with all
accessories,Junction Box,Joints as required and demanded by engineer-
incharge and laying/erecting as per OEM guidelines and as per
instruction of engineer incharge having following size of dimensions and
No of compartments (W x D x T) Cat-III [6] 300mm x 25mm x 1.6 mm
with Three Compartments
256 Providing and erecting Mains with 1.1 KV grade FRLSH PVC insulated ISI 16360.000 Mtr. 82.82
marked stranded Copper conductor wire in following type of pipe to be
erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper
conductor FRLSH PVC insulated stranded wire of green colour for earth
continuity of following size (A) with medium class Rigid PVC pipe and
accessories (b) 2 wire 2.5 sq. mm
257 Providing and erecting Mains with 1.1 KV grade FRLSH PVC insulated ISI 1900.000 Mtr. 112.11
marked stranded Copper conductor wire in following type of pipe to be
erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLSH
PVC insulated stranded wire of green colour for earth continuity of
following size (A) with medium class Rigid PVC pipe and accessories (a)
wire 4 sq. mm
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
258 Providing and erecting Mains with 1.1 KV grade FRLSH PVC insulated ISI 120.000 Mtr. 147.46
marked stranded Copper conductor wire in following type of pipe to be
erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLSH
PVC insulated stranded wire of green colour for earth continuity of
following size (A) with medium class Rigid PVC pipe and accessories (b)
wire 6 sq. mm
259 Providing and erecting Mains with 1.1 KV grade FRLSH PVC insulated ISI 3280.000 Mtr. 425.21
marked stranded Copper conductor wire in following type of pipe to be
erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLSH
PVC insulated stranded wire of green colour for earth continuity of
following size (A) with medium class Rigid PVC pipe and accessories (i)
wire 10 sq. mm (use earth wire of 4 sq.mm )
260 providing and erecting Mains with ISI marked, 1.5KV FRLSH grade 720.000 Mtr. 142.41
electrolyte multi stranded, annealed copper conductor with heat resistant
PVC insulated conforms to IS 694, IEC - 227 erected in existing pipe of
following size (Specifically for control panel, relays, power switchgears,
motor starters & control wiring) with required size of copper lugs, nuts and
bolts if required. (g) One wire 16.00 sq. mm
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
261 providing and erecting Mains with ISI marked, 1.5KV FRLSH grade 70.000 Mtr. 300.98
electrolyte multi stranded, annealed copper conductor with heat resistant
PVC insulated conforms to IS 694, IEC - 227 erected in existing pipe of
following size (Specifically for control panel, relays, power switchgears,
motor starters & control wiring) with required size of copper lugs, nuts and
bolts if required. (i) One wire 35.00 sq. mm
262 providing and erecting Mains with ISI marked, 1.5KV FRLSH grade 50.000 Mtr. 470.66
electrolyte multi stranded, annealed copper conductor with heat resistant
PVC insulated conforms to IS 694, IEC - 227 erected in existing pipe of
following size (Specifically for control panel, relays, power switchgears,
motor starters & control wiring) with required size of copper lugs, nuts and
bolts if required. (j) One wire 50.00 sq. mm
263 providing and erecting Mains with ISI marked, 1.5KV FRLSH grade 80.000 Mtr. 919.10
electrolyte multi stranded, annealed copper conductor with heat resistant
PVC insulated conforms to IS 694, IEC - 227 erected in existing pipe of
following size (Specifically for control panel, relays, power switchgears,
motor starters & control wiring) with required size of copper lugs, nuts and
bolts if required. (l) One wire 95.00 sq. mm
264 Supplying and erecting Flexible FRLSH PVC insulated multi strand multi 200.000 Mtr. 46.46
core 1.1 kv grade ISI marked copper wires of following size to be erected
as directed. (e) 1.50 Sq.mm 3 core round PVC sheathed
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
265 Providing & Erecting approved make following size of TV Co-axial flexible 120.000 Mtr. 62.62
cable comprising inner conductor of solid bare copper insulated with Foam
PE & Secondary conductor made of poly - Aluminium film bonded Al.
Braids @ suitable coverage overall sheathed with black PVC insulation.
266 Supplying & erecting approved make Telephone Cable electrolytic copper 40.000 Mtr. 20.20
conductor PE insulation twisted in two pairs, & wrapped with FRLSH
PVC tape & sheathed with PVC or HFFR outer Jacket suitable for
telephone wiring & confirming to C-DOT erected in existing pipe. of
following size of conductors & nos.of pairs. With necessary connections.
[A] Conductor Size 0.5 mm (a) Unarmoured 2) Two Pairs
267 Supplying & erecting approved make Telephone Cable electrolytic copper 40.000 Mtr. 125.24
conductor PE insulation twisted in two pairs, & wrapped with FRLSH
PVC tape & sheathed with PVC or HFFR outer Jacket suitable for
telephone wiring & confirming to C-DOT erected in existing pipe. of
following size of conductors & nos.of pairs. With necessary connections.
[A] Conductor Size 0.5 mm (b) Armoured [Jelly Filled] (1) Ten Pairs
268 Supplying & erecting approved make LAN cable of following size in 1400.000 Mtr. 47.47
existing pipe as per direction[C] CAT -
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
269 Providing & erecting main Distribution (MDF) indoor type, back mounted 1.000 Ea 994.85
frame as per DoT standard approved with krone strips (a) Suitable for
270 Providing & erecting Switch board for Computer or electric apparatus 38.000 Ea 1133.22
consisting of following modular type accessories mounted with PVC /
Metallic concealed/open box with single mounting base frame covered
with textured/metallic /white front plate,modules erected with necessary
connections as directed
1 no. 6A/16A universal plug-switch combined.
3 nos. 6A Switch
3 nos. 6A 5 pin Plug For Modular Type Accessories.Cat-III
271 Decorative call bell Ting-tong box type 250 volts complete erected 5.000 Ea 71.71
272 Supply of Fibreglass Step (A Type) Ladder - 6 FT having following 1.000 Ea 13940.02
specifications :
It should have nonconductive Structural moulded top, with Slots to keep
tools close at hand, inside Spreader Braces, Aluminium Feet with thick
rubber tread, nonconductive Full channel Fibreglass and two pairs of
gusset support at the bottom step. All gussets are heavy duty steel.
Capacity : 300 lbs. Step Size : 3” Width : 23” “Approx.
Spread : 41” Approx.
Wt. : 11 Kg Approx. Cube : 6.2’
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
273 Supply of Fibreglass Platform Step (A Type) Ladder - 18 FT having 1.000 Ea 35681.28
following specifications :
It should have large fully serrated
platform 15” wide 20” deep which locks ladder , Aluminium feet with thick
rubber tread, top rail guard to serve as a railing, two pairs of gusset
support at the bottom step and All gussets are heavy duty steel. Capacity
274 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt 744.000 Ea 373.70
to 0.5 Watt assembled on single MCPCB, with housing used as a heat
sink shall be made of thick sheet Steel conforming to IS: 513/CRCA/
aluminium die cast powder coated and high U.V. & corrosion resistance
with diffuser with company mark/name 160V to 270V, Power Factor more
than 0.95, THD < 15%,
CCT 3000 K to 6500K,
Luminaire efficacy> 85 lumens/watt ,LED
LED driver efficiency > 85 %
( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description
have shown ranges of Wattage capacity of LED fittings.The Engineer
(A) Tube Light with integral/ non-integral driver .
(iv) 22-24 Watts, Surge - 2KV,IP-20, conventional 4 feet Cat III
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
275 Supplying and erecting led lamps with following wattage capacity of 220 to 265.000 Ea 112.11
240 voltage, minimum 15000 burning hours life, 500 V in built-surge
protection,Polycarbonate diffuser, mounting suitable for E14 / E27 / B22
lamp holders, pf >=
(A) LED Lamps integral type, with PC diffuser suitable LAMP holder
(i) 5 to 8 watts Cat-III
276 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt 390.000 Ea 427.23
to 0.5 Watt assembled on single MCPCB, with housing used as a heat
sink shall be made of thick sheet Steel conforming to IS:
513/CRCA/aluminium pressure die cast powder coated and high U.V. &
corrosion resistance with diffuser housed in aluminium casted body with
company mark/name
160V to 270V,Power Factor more than 0.95, THD < 15 %,
CCT 3000 K to 6500K,
Luminaire efficacy> 85 lumens/watt
LED driver efficiency > 85 %
( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description
have shown ranges of Wattage capacity of LED fittings.The Engineer
(A) Square/ Circular shaped Surface/Recessed Mount Downlight with
provision for spring loaded mounting clips complete.IP20
(ii) 11-15 watts, Surge-2 KV Cat-III
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
277 Supplying and erecting LED street light / Flood light fittings with High 25.000 Ea 5976.17
power White LEDs wattage of 3 Watt and above assembled on single
MCPCB, efficiency more than 130 lm/w and corrosion free High pressure
die cast aluminum housing with smooth finish powder coated and heat
sink extruded aluminium with diffuser and Polycarbonate optics/ lenses,
with toughened glass with company mark/name engraved or embossed
160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to
5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED
driver efficiency > 85 %.( fittings required LM-79 & LM-80
certificates)(NOTE: Below description have shown ranges of Wattage
capacity between the ranges shown.) (A) Street Light (IP-65), Surge
protection -4KV integral and ,Light must have 440VAC line supply with
over-voltage protection. (iii) Above 60 to 90 watts. Cat-III
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
278 Supplying and erecting LED street light / Flood light fittings with High 12.000 Ea 9647.52
power White LEDs wattage of 3 Watt and above assembled on single
MCPCB, efficiency more than 130 lm/w and corrosion free High pressure
die cast aluminum housing with smooth finish powder coated and heat
sink extruded aluminium with diffuser and Polycarbonate optics/ lenses,
with toughened glass with company mark/name engraved or embossed
160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to
5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED
driver efficiency > 85 %.( fittings required LM-79 & LM-80
certificates)(NOTE: Below description have shown ranges of Wattage
capacity between the ranges shown.) (B) Flood Light (IP-65), Surge
protection -4KV integral and ,Light must have 440VAC line supply with
over-voltage protection(vi) above 160 to 200 watts
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
279 Supplying and erecting LED street light / Flood light fittings with High 4.000 Ea 4819.72
power White LEDs wattage of 3 Watt and above assembled on single
MCPCB, efficiency more than 130 lm/w and corrosion free High pressure
die cast aluminum housing with smooth finish powder coated and heat
sink extruded aluminium with diffuser and Polycarbonate optics/ lenses,
with toughened glass with company mark/name engraved or embossed
160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to
5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED
driver efficiency > 85 %.( fittings required LM-79 & LM-80
certificates)(NOTE: Below description have shown ranges of Wattage
capacity between the ranges shown.) (C) Post Top Lantern LED fitting
comprises of finish cast aluminum spigot and spun aluminum canopy fixed
with opal polycarbonate, pipe arrangement for vertical mounting driver and
accessories wired upto terminal block.IP 65 (ii)32-40W Cat-III
280 Providing and erecting Approved make Four pole moulded case circuit 20.000 Ea 6173.12
breaker having breaking capacity ICU of 25 KA. at 415 V,having normal
current rating up to 25 A to 100A. with Fixed thermal & magnetic release
suitable to work on A.C. supply 50 c/s. with all internal connections,
spreader tinned copper & complete erected in existing 16 G.M.S. housing.
ICS=100% of ICU only Cat III
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
281 Providing and erecting Approved make Four pole moulded case circuit 3.000 Ea 8055.76
breaker having breaking capacity ICU of 25 KA. at 415 V,having normal
current rating up to 25 A to 100A. with Fixed thermal & magnetic release
suitable to work on A.C. supply 50 c/s. with all internal connections,
spreader tinned copper & complete erected in existing 16 G.M.S. housing.
ICS=100% of ICU only Cat III
282 Providing and erecting Approved make Four pole moulded case circuit 18.000 Ea 16221.61
breaker having breaking capacity ICU of 35 KA. at 415 V. having Normal
current rating 200A.with variable Thermal & magnetic release suitable to
work on A.C.supply 50 c/s. with all internal connections, spreader tinned
copper & complete erected in existing 16 G.M.S.housing ICS=100% of
ICU only Cat III
283 Providing and erecting Approved make Four pole moulded case circuit 3.000 Ea 20946.39
breaker having breaking capacity ICU of 35 KA. and above at 415 V .
having normal current rating 250A. with variable thermal & magnetic
release suitable to work on A.C.supply 50 c/s. with all internal
connections, spreader tinned copper & complete erected in existing
G.M.S. housing. ICS=100% of ICU only Cat III
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
284 Providing and erecting Approved make Four pole moulded case circuit 1.000 Ea 30733.29
breaker having breaking capacity ICU of 50 K.A. and above at 415 V
having normal current rating 800A.with variable thermal & magnetic
release suitable to work on A.C.supply 50 c/s. with all internal
connections, spreader tinned copper & complete erected in existing
G.M.S.housing. ICS=100% of ICU only Cat III
285 providing and erecting Approved make standard manually operated fixed 1.000 Ea 85012.71
type 4 Pole Air circuit breaker. Having following kA breaking capacity with
ICU=ICS=ICW (1 sec),Vsr=690 v, Ui=1kv (2) with microprocessor Release
with over load, short circuit, earth fault protection (L.S.I.G.) and metering
display in modular design with LED display and Test Trip button facility,
CTs and auxiliary contacts, of following current ratings. (A) 800Amp 50kA
286 providing and erecting Approved make standard manually operated fixed 3.000 Ea 88993.12
type 4 Pole Air circuit breaker. Having following kA breaking capacity with
ICU=ICS=ICW (1 sec),Vsr=690 v, Ui=1kv (2) with microprocessor Release
with over load, short circuit, earth fault protection (L.S.I.G.) and metering
display in modular design with LED display and Test Trip button facility,
CTs and auxiliary contacts, of following current ratings. (ii) 1000Amp
kA Cat III
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
287 Providing and erecting Approved make Earth fault Relay suitable to mount 11.000 Ea 4687.41
with inter connection suitable to following size of moulded case circuit
breaker having CT ratio & MCCB rating as following along with shunt trip
220V AC. with all internal connections & complete erected in existing
M.S.housing. (1) 15 A -100 A , CT Ratio 1/100
288 Providing and erecting Approved make Earth fault Relay suitable to mount 11.000 Ea 4983.34
with inter connection suitable to following size of moulded case circuit
breaker having CT ratio & MCCB rating as following along with shunt trip
220V AC. with all internal connections & complete erected in existing
M.S.housing. (2) 125 A -200 A , CT Ratio 1/200
289 Providing and erecting Approved make Earth fault Relay suitable to mount 1.000 Ea 5415.62
with inter connection suitable to following size of moulded case circuit
breaker having CT ratio & MCCB rating as following along with shunt trip
220V AC. with all internal connections & complete erected in existing
M.S.housing. (3) 250 A -400 A , CT Ratio 1/400
290 Providing and erecting Approved make Earth fault Relay suitable to mount 4.000 Ea 6056.97
with inter connection suitable to following size of moulded case circuit
breaker having CT ratio & MCCB rating as following along with shunt trip
220V AC. with all internal connections & complete erected in existing
M.S.housing. (4) 600 A -800 A , CT Ratio 1/800
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
291 Supplying and erecting triple pole & neutral 440V / 500V panel mounting 21.000 Rn.Mtr 1961.42
Copper Busbars with four equal Nos. of electrolyte bus having current
density not more than 1.6 Amp. / sq.mm (Rated current / cross section
area) duly wrapped with colour insulating tape for phase sequence of
following current carrying capacity, erected with necessary bus bar
supports /insulators, main cable socket to each bar, erected in existing
cubical panel with necessary connections. (A) Suitable for 100 Amp.
292 Supplying and erecting triple pole & neutral 440V / 500V panel mounting 5.000 Rn.Mtr 3202.71
Copper Busbars with four equal Nos. of electrolyte bus having current
density not more than 1.6 Amp. / sq.mm (Rated current / cross section
area) duly wrapped with colour insulating tape for phase sequence of
following current carrying capacity, erected with necessary bus bar
supports /insulators, main cable socket to each bar, erected in existing
cubical panel with necessary connections. (B) Suitable for 200 Amp.
293 Supplying and erecting triple pole & neutral 440V / 500V panel mounting 7.000 Rn.Mtr 4909.61
Copper Busbars with four equal Nos. of electrolyte bus having current
density not more than 1.6 Amp. / sq.mm (Rated current / cross section
area) duly wrapped with colour insulating tape for phase sequence of
following current carrying capacity, erected with necessary bus bar
supports /insulators, main cable socket to each bar, erected in existing
cubical panel with necessary connections. (C) Suitable for 300 Amp.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
294 Supplying and erecting triple pole & neutral 440V / 500V panel mounting 10.000 Rn.Mtr 16499.36
Copper Busbars with four equal Nos. of electrolyte bus having current
density not more than 1.6 Amp. / sq.mm (Rated current / cross section
area) duly wrapped with colour insulating tape for phase sequence of
following current carrying capacity, erected with necessary bus bar
supports /insulators, main cable socket to each bar, erected in existing
cubical panel with necessary connections. (G) Suitable for 1200 Amp.
295 providing and erecting Miniature circuit breaker single pole 6A to 25A 1545.000 Ea 112.11
suitable to operate on 240 V A.C. system and having breaking capacity
10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI
Mark Cat-III
296 Providing & erecting 240 V MCB double pole switch for lighting Load (B 2.000 Ea 295.93
Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing
box having following capacity (B) 40 Amp. Cat-III
297 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C 143.000 Ea 737.30
Curve) having 10KA breaking capacity & confirms to IS :8828 in existing
box having following capacity (B.) for 63 Amp. Cat-III
298 (A) single phase incoming and horizontal single phase outgoing (b) sheet 2.000 Ea 1152.41
steel double door (IP-43) (iii)8 way
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
299 Providing and erecting Sheet Steel powder coated MCB distribution board - 36.000 Ea 3412.79
flush / surface mounted fitted with busbar, neutral link, earth bar and DIN
rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house
appropriate nos. of MCBs.(The DBs should be used of same company of
MCB to be used) suitable for
(B) three phase incoming and single phase horizontal type outgoing Per
phase isolation type (PPI) (b) sheet steel double door (iii)8 way
300 providing and erecting Approved make RCCBs conforming to IS: 12640 256.000 Ea 2235.13
and having sensitivity of 30 mA and Short Circuit withstand capacity of
KA and suitable for operation on single phase 240 V,50Hz. having
characteristic of quick action & tripping with all advance feature & do not
incorporate any electronic component. for following Max. rating erected
as directed (iI) 40 Amps.DP Cat. III
301 Providing and erecting Approved make RCCBs conforming to IS: 12640 2.000 Ea 4314.72
and having sensitivity of 30 mA and Short Circuit withstand capacity of
KA and suitable for operation on 3 phase and neutral 415V,50Hz. having
characteristic of quick action & tripping with all advance feature & do not
incorporate any electronic component for following Max. rating erected as
directed. with necessay enclosure (iv) 100 Amps. FP (100 mA Sensitivity)
302 Providing and erecting required size Copper strip for earthing of H.T. OCB 60.000 Kg. 794.87
/ ACB/ Transformer, LT panel board, Motors etc. using copper clamp.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
303 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. 100.000 Kg. 794.87
304 Supplying & erecting earth pit of minimum bore dia.150mm size approved 15.000 Ea 4591.46
make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS
3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe
dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm
having 200-250 Micron galvanising, connection terminal dia of 12mm with
constant ohmic value surrounded by highly conductive compound with
high charge dissipation suitable for following type of applications with
chamber and heavy duty cover. (A)(approved make OEM has to submit
test certificate including value of earth resistance of installation duly
stamped and signed by agency and officer Incharge has to ensure the
value of earthing resistane mentioned in test Certificate) & having back
filling compound of (B) Inner chemical (CCM Compound)- Resistivity:-
ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no
load & dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing
compound should be capable to retain moisture for long time Necessary
test report must be submitted by Agency.
(a) For Electrical Installation up to 440V in normal soil
Length of pipe - 1 Mtr
Back filling compound - 1 Nos Bag of 15 Kg.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
305 (c) For Electrical Installation covering Transformer Neutrals, Lightning 20.000 Ea 8636.51
arrester Earthing, A.C.Plant & Sensitive Computer System(like
Automation, SCADA) i.e independent Earthing in normal soil.
Length of Pipe : 3.00 mtrs
Back filling Compound :2 nos Bags of 25 Kg.
306 Providing & erecting weather proof, dust & vermin proof, floor mounted front 22.000 Sq.Mtr 14902.55
operated indoor type cubical panel board necessary IP-42 and above
protection as per approval from engineer incharge made from 14 SWG thick
CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for
internal partitions with necessary accesories , supporting angles/ flats channel
including cutting, bending, drilling, welding, riveting with internal partitions &
cable alley as per requirements & instruction of engineer-in-charge with erection
of supplied switch gears, BUSBARS, suitable size of inter connecting PVC
copper wire / copper-aluminium strips, rubber grommets, rib, bakelite control
fuses/MCB for measuring instruments, earth bus & earth bolts, foundation
flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking
arrangement and rubber gasket,heavy duty end terminal connection,danger
notice board,necessary ventilation,earthing strip complete. The Panel shall be
painted with epoxy powder coating.
(The rates excludes the cost of switchgears, bus bars, inter connecting mains &
Copper Aluminium strips, meters, Fuses etc. The dimension shall be measured
excluding base beams) The panel shall be supplied with following approved
manufacturers with following size. (B) The standard companies switch gear
shall be used and only manufacturers at CPRI approved factory
(i) with 350mm depth
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
307 Providing & erecting weather proof, dust & vermin proof, floor mounted front 20.000 Sq.Mtr 40999.94
operated indoor type cubical panel board necessary IP-42 and above
protection as per approval from engineer incharge made from 14 SWG thick
CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for
internal partitions with necessary accesories , supporting angles/ flats channel
including cutting, bending, drilling, welding, riveting with internal partitions &
cable alley as per requirements & instruction of engineer-in-charge with erection
of supplied switch gears, BUSBARS, suitable size of inter connecting PVC
copper wire / copper-aluminium strips, rubber grommets, rib, bakelite control
fuses/MCB for measuring instruments, earth bus & earth bolts, foundation
flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking
arrangement and rubber gasket,heavy duty end terminal connection,danger
notice board,necessary ventilation,earthing strip complete. The Panel shall be
painted with epoxy powder coating.
(The rates excludes the cost of switchgears, bus bars, inter connecting mains &
Copper Aluminium strips, meters, Fuses etc. The dimension shall be measured
excluding base beams) The panel shall be supplied with following approved
manufacturers with following size. (B) The standard companies switch gear
shall be used and only manufacturers at CPRI approved factory
(iv) with 1000 mm. depth
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
308 Providing , erecting , fabricating the M.S. structure as per requirement on 280.000 Kg 77.77
site incorporating proper size of M.S. angles,square,round, flats, bars,
channels, sections complete with cutting, welding, grinding & finishing duly
painted with one coat of red oxide with erection on site as per direction of
engineer in charge with necessary grouting, cementing, plastering &
finishing complete.
309 Providing and erecting multifunctional meter suitable for application of 12.000 Ea 14123.84
Power monitoring and showing measurement of following Voltage,
Frequency, Apparent energy, Apparent power, Active and reactive energy,
Active and reactive power, Average voltage Vavg, Peak demand power
PM, QM, SM, Demand power P, Q, S, Apparent power S, S1, S2, S3,
Unbalance current, Power factor and displacement PF (signed, four
quadrant), Calculated neutral current, Active, reactive, apparent energy
(signed, four quadrant), Active power P, P1, P2, P3, Voltage U21, U32,
U13, V1, V2, V3, Phase currents, Average current Iag, Peak demand
currents, Reactive power Q, Q1, Q2, Q3, Demand current I1, I2, I3, [Us]
rated supply voltage 40...300 V AC 45...65 Hz, 40...300 V DC, Network
frequency 50 Hz, Type of network 3P, Display type 7 segments LED,
Display colour Red, Messages display capacity 3 fields of 4 characters,
Display digits 12 digit(s) - 14.2 mm in height
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
310 Providing and erecting FRLSH XLPE(IS:7098)(I)-88 ISI armoured cable 250.000 Mtr. 540.35
multistrand Aluminium conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe of following size of cables
with necessary lugs and glands (F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm
311 Providing and erecting FRLSH XLPE(IS:7098)(I)-88 ISI armoured cable 1080.000 Mtr. 1168.57
multistrand Aluminium conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe of following size of cables
with necessary lugs and glands (I) 3 1/2 core 240 Sq. mm( 120 Sq. mm
312 Providing and erecting FRLSH XLPE(IS:7098)(I)-88 ISI armoured cable 220.000 Mtr. 1747.30
multistrand Aluminium conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe of following size of cables
with necessary lugs and glands (K) 3 1/2 core 400 Sq.mm ( 185 Sq. mm
313 Providing and erecting FRLSH XLPE (IS:7098)(I)-88 ISI armoured cable 1200.000 Mtr. 126.25
multistrand / Solid Aluminium conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe of following size of cables
with necessary lugs and glands. (B) 4 core 6 Sq. mm
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
314 Providing and erecting FRLSH XLPE (IS:7098)(I)-88 ISI armoured cable 200.000 Mtr. 153.52
multistrand Aluminium conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe of following size of cables
with necessary lugs and glands. (A) 4 core 16 Sq. mm
315 Providing and erecting FRLSH XLPE(IS:7098)(I)-88 ISI armoured cable 220.000 Mtr. 209.07
multistrand Copper conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe of following size of cables
with necessary lugs and glands. (B) 2 core 4 Sq. mm
316 Making trench in soft soil of suitable width of 90 cm deep for laying cable 3000.000 Mtr. 55.55
or locating the fault all over the run and back filling the same and making
the surface as normal ground.
317 Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or 250.000 Mtr. 74.74
required depth for laying any size of cable or locating the fault all over the
run and back filling the same and making the surface as normal ground.
318 (B) If additional machinery like hammer driller or JCB use [Add] 100.000 Mtr. 357.54
319 Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cm. below 100.000 Mtr. 456.52
ground across the road crossing or on floor with necessary material in an
approved manner and making the ground as per original. (A ) 450 mm dia
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
320 Providing & laying approved make Double walled corrugated pipes 500.000 Mtr. 62.62
(DWC) of polyethylene(conforming to IS 14930 II )with necessary
connecting accessories of same material at required depth in existing
trench for laying of cable. below ground / road surface for enclosing
cable (A) 50 mm Outer Dia
321 Providing and fixing approved make Perforated C type cable tray. Made 40.000 RMT 622.16
from sheet steel. The cable tray should be single or double bended as per
required and as per IS 2062/1079 and shall be coated with hot dip
galvanizing as per IS 2629/4759. with max 17.5% perforation with coupler
plate / Fish plate and GI hardware like nut - bolt and washers etc. erection
with necessary support( included) as per Specification and as per
instruction of engineer in charge.. (5) 300 X 50 X 2.0 mm Thick
322 Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan 653.000 Ea 1948.29
with double ball bearing ISI mark with Condenser 230 volt A.C. 50 Hz
1200 mm sweep complete having 3blades with aluminium blades with
canopy & 30 cm. down rod erected with earthing.(Make shall be approved
by Engineer in charge))
323 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. 653.000 Mtr. 108.07
Pipe down rod erected duly painted for fan complete with proper insulation
without leckage and earthing.
324 Supplying & erecting Fan Hook of 10 mm M.S. Round bar grouted in RCC 653.000 Ea. 43.43
slab with Making the site as original.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
325 Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to 653.000 Ea 108.07
the RCC bars up to 50mm length each side and pierced through a
Gauge M.S. box / Heavy Duty PVC box complete erected concealed in
Ceiling with necessary finishing.
326 Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or 653.000 Ea 18.18
327 Supplying & erecting approved make low noise decorative exhaust fan 70.000 Ea 1703.87
having square frame ABS body with inbuilt lowers & square frame 200mm
with 1350RPM Cat-II
328 Supplying & erecting single phase approved make industrial exhaust fan 34.000 Ea 3082.52
suitable for medium duty ring mounted low noise operation suitable for
medium duty having following dia size and maximum speed in RPM [C]
380 mm dia 1400 RPM cat II
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
329 Supplying and erecting approved make Octagonal pole made from HR 16.000 Ea 8192.11
sheet steel. The pole should be made as per IS. and shall be coated with
hot dip galvanizing as per IS 2629/2633/4759, suitable suspend local wind
speed with integral Junction box consist of terminal plate of min 6mm
Hylam sheet, standard profile 35mmX7.5mm Din-Rail for MCB Mounting,
stud type terminal and arrangement for cable termination to be erected
With Suitable foundation (Included) as per details given by manufacturer
considering site requirement.(D) 6 Mtr. Long 70 mm Top X 135 mm
bottom dia, 3 mm thickness with 200mmX200mmX12mm base plate, 4-
M20 Bolts and 600mm long with necessary G.I. J Bolts .Approx Pole
weight 59 kg
330 Supplying & erecting approved make SMC press moulded composite 15.000 Ea 515.10
FRP. loop-in, loop-out approx. 2mm thick box complete with Bakelite
connector strip 5way(3P+N+E),DIN rail for mounting mob & hinged doors
as per requirement having locking arrangements with mounting clamp with
nuts, bolts & washers suitable for erection on pole with cable clamps&
earth bolt of following size of box. (b) 250mm x 200mm x 100mm [deep]
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
331 Providing street light pole bracket comprising main B Class MS pipe of 4.2 10.000 Ea 561.56
cm/require outside dia. complete with suitable B Class M.S. sleeve tubing
of approx. 45cms.length and suitable for 76.5 mm / 80mm. / require size
pole top having sufficient fastners for fixing the brackets and having
spread of 1 mtr. length with suitable rise as per site condition & suitable
welded stiffener reducer and nipple with check nut complete painted with
one coat of Red oxide / PU base primer and two coats of Aluminium / PU
paint. paint with following nos of arms. [A] Single Arm bracket 1 Mtr
332 Providing street light pole bracket comprising main B Class MS pipe of 4.2 6.000 Ea 758.51
cm/require outside dia. complete with suitable B Class M.S. sleeve tubing
of approx. 45cms.length and suitable for 76.5 mm / 80mm. / require size
pole top having sufficient fastners for fixing the brackets and having
spread of 1 mtr. length with suitable rise as per site condition & suitable
welded stiffener reducer and nipple with check nut complete painted with
one coat of Red oxide / PU base primer and two coats of Aluminium / PU
paint. paint with following nos of arms. [B] Double Arm Bracket 1 Mtr
333 Providing and erecting Pipe type earthing having 150 cms.long and 2.5 16.000 Ea 368.65
cms. dia. galvanised iron pipe with coupling and buch buried in specially
prepared earth pit complete with necessary 8 SWG earth wire.
334 For using salt and charcoal / coke as required for pipe type earthing. 16.000 Ea 171.70
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
335 Providing and erecting Inverter based approved make split air-conditioning 29.000 Ea 56353.96
unit consisting of condensing unit with variable speed fan motor, inverter
type hermetically sealed rotary compressor with accessories etc. duly
connected separately erected evaporating unit and blower motor with its
accessories by means of extra supplied proper insulated copper
tubing,drain PVC pipes suitable for ( cost includes Eco Friendly green gas
charging and 15A plug top & Remote Control & MS Stand) with necessary
core cutting.
(1)For ISEER Range (KWH/KWH)(3.1 to 3.99)
(C) for 1.7 to 2 ton capacity-Premium Cat.
336 Supplying and erecting insulated pair of soft copper tubing open or 290.000 Rmt. 965.56
concealed including power and control cable,necessary PVC drain pipes
for Split AC machine up to 4 TR capacity
337 Providing & Erecting full SS Body (SS 304) Split type water cooler having 9.000 Ea 61115.10
storage capacity 160 to 175 Ltr.(Tank SS 304) & Cooling capacity 150 ltr.
Per hour @ an ambient temp of 350 C.The outlet temp. of the water
should drop by 150C within a hour,The water cooler should be comprising
of hermetically sealed Reciprocating compressor with R134A, fan motor,
Copper Condensing unit with company fabricated Outdoor Unit water tank
surrounded by evaporating coil, thermostats, relay etc.complete with
necessary copper tube & Insulation, M.S Chanel Stand with Painting for
water tank & M.S. Powder Coated Stand for Outdoor unit with Installation.
With DPELCB and 4 Way DB Box with accessory Three core Cord for
connection.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
338 Supplying & erecting reverse osmosis (RO) water purification system with 9.000 Ea 29187.99
M.S. powder coated pedestal frame, prefilter housing carbon filter suitable
buster DC pump, auto low & high pressure switches with following size of
LPH capacity & erected as directed [C] 50 Ltr / Hr with 150 psi 2 nos
booster pump
339 Supplying, installing, testing & commissioning of SOLAR WATER heating 2.000 Ea 189956.76
system as per prevailing IS code comprising of Solar flat locket collector,
stainless steel hot water storage isolated tank with S.S. heat exchanger,
absorber made of copper sheet & copper tube of following capacity in liter
/ day (LPD) with "B" size aluminium box collector with appropriate capacity
electrical backup arrangement (Excluding inlet & outlet pipe lines) (E)
Capacity of 1000 LPD
340 Providing & erecting L.T. Current Transformer with bar primary 50/5 to 36.000 Ea 274.72
1000/5 ratio 15 VA burden erected in existing CRCA box duly secured
with insulating materials connected to the meter
341 Supplying and erecting approved make suitable panel indicator LED type 36.000 Ea 43.43
lamp, lens cover, complete erected with necessary connections.
342 Providing & erecting open well horizontal mono block pump set with cast 2.000 Ea 53865.32
iron body, complete for three phase submersible motor having[I] For
HP 3 phase open well horizontal mono block pump set suitable for
LPM to 1150 LPM @ 33 to 51 MTR head suitable for 65 /80 mm dia
delivery pipe cat II
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
343 Supplying & erecting approved make motor control cubical panel [Star 2.000 Ea 18643.59
delta] made from 16G CRCA sheet duly epoxy powder painted inside and
outside with hinged doors and locking with suitable size of ON - OFF
isolator (AC 3 / 23 duty) main fuses. Digital volt and current meter (in a
single unit) with micro controller based control unit and current sensing
single phasing preventer electronic overload protection, over voltage
(Programmable) protection and under voltage (Programmable) protection,
prod less dry run protection programming facility for setting of all
parameter like overload current, high voltage limit, low voltage limit, dry
run limit with digital indication on seven segment LED display for any fault
like over load, high voltage, low voltage, dry running single crimped,
electronic star delta timer, feather touch start / stop push buttons to be
erected on angle iron frame. Grouted on wall the contactors will be of L&
T, Siemens , BCH make only)(E) S/D up to 22.5 H.P.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
344 Supplying and erecting approved make3 phase motor control panel (ATS) 1.000 Ea 55786.34
made from 16 G. CRCA sheet duly painted with epoxy power paint inside
and outside with hinged doors and locking arrangement, consisting, of
suitable switch of AC 23 duty with HRC fuses (Cat.III), starting and
running contactors, overload relay, Automatic water level controller,
phasing preventer , water level guard, over load, start, run and stop push
buttons, air cooled auto transformer with 60%, 70%, 80% tapping, Panel
to be erected on angle iron frame grouted on wall as directed., contactors
relays, timer etc. shall be of L & T Siemens / Cutler Hammer make. (e)
Suitable for 50 H.P.
345 S.I.T.C. submersible pump set for bore of 200 mm. dia. or more having 3 1.000 Ea 109029.50
phase motor capacity about 50-55 H.P discharge capacity having . Lifting
and Lowering taken extra. (C) ( 8 Stage) 1400 to 1100 L.P.M. discharge at
the head 113 to 138 mtrs. suitable for 100 mm dia. Delivery pipe having
346 Lowering of submersible motor pump set at the depth of following 1.000 Per Job 2996.67
,complete with required. Nos. and size of casing pipes erected by means
of proper chain pulley block & pipe wrenches after checking of threads of
each pipe with coupling to take the load of the pump set and pipe
assembly filled up with water (c)Above 120 mtr.
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
347 Lowering of submersible motor pump set at the depth of following 2.000 Per Job 1711.95
,complete with required. Nos. and size of casing pipes erected by means
of proper chain pulley block & pipe wrenches after checking of threads of
each pipe with coupling to take the load of the pump set and pipe
assembly filled up with water (d)For Open well Horizontal submersible
pump set for sump well (iii) Above 15 HP
348 Providing and erecting ISI marked FRLSH PVC insulated PVC Sheathed 60.000 Mtr 295.93
Flat flexible Submersible copper cable approved make of following Size.
(E) 3 Core x 10 Sq. mm.
349 Providing and erecting ISI marked FRLSH PVC insulated PVC Sheathed 320.000 Mtr 647.41
Flat flexible Submersible copper cable approved make of following Size.
( G)3 Core x 25 Sq. mm
350 Providing Water proof straight Joint in PVC insulated flat flexible copper 6.000 Ea 278.76
cable by using insulating material, water proofing material, & making the
joint complete. (B) 16 to 35 Sq. mm
351 Supplying of following size of HEAVY UPVC column pipe with coupler 300.000 Rmt 1130.19
and wire lock [E] 100 mm dia
352 Supply of following size of TOP & BOTTOM accessories i.e. Adaptor set 2.000 Per Set 3872.34
(CI) long, pump guard set, starter pipe Rubber ring for submersible pump
& UPVC column pipe as directed by Engineer - in - charge with necessary
plumbing as desired.[G] 100 mm dia
Description of Item (with brief specification and reference to book of Total
Item No. Quantity Unit Rate in Figures
specifications) Amount
353 Supplying, & erecting C.I. swing, check type non-return (Reflux) Valve -ISI 2.000 Ea 2868.40
marked suitable for following size (D) 100 mm dia.
354 Supplying, Erecting, Testing & Commissioning the Machine Room Less
Passenger lift as per prevailing IS code having following main features:
(A) GENERAL DESCRIPTION OF LIFTS.
[1] GEAR LESS LIFT DRIVE (MRL) comprising of High Starting torque Lift
3 phase 440 V A. C. Permanent Magnet Synchronous motor of proper
rating with high efficiency shall be used.[2] Micro processor based / PLC,
ACVVVF, vector control drive with encoder feedback closed loop system
shall be used for lift car and door operation which shall be full collective
Main, Up/ Down Contactor with overload and phase reversal relay and
safety controls.
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
RAW_HTML
001-Pre-Qualification Bid (New Hostel Gujarat College).pdf
002-PQ GR Dt.20-6-2020.pdf
003-PQ GR Dt.6-7-2020.pdf
005-Sch-B (New Hostel Gujarat College).pdf
006-Specification Index (New Hostel Gujarat College).pdf
007-Specification (New Hostel Gujarat College).pdf
008-GR as per SBD (12-01-2024)-Navrangpura.pdf
009-Standards for Cement Con. Dt.11-5-2017.pdf
010-Single Tender GR Dt.18-2-2017.pdf
011-Tender Negotiation Dt.08-06-2018.pdf
012-Testing Schedule Dt.24-10-1994.pdf
013-GR Regarding Laplength in Reinforcement Dt.15-2-2017.pdf
014-FD Circular No 1097 GST Dt.15-9-2018.pdf
015-Registration Mandatory Dt.3-9-2016.pdf
016-Tender Reinvite Guideline Dt.25-8-2015.pdf
017-E-Tendering-Tender Fee and EMD Dt18-1-2008.pdf
018-E-Tendering-Tender Fee and other doc Dt.27-11-2008.pdf
019-Payment through RTGS-NEFT Dt.30-4-2018.pdf
020-RMC for above 5 cr works Dt.15-07-2023.pdf
021-COMPUTERISED MB GR Dt.1-2-2017.pdf
022-Bond-Colour.pdf
023-Bond-Water proofing.pdf
024-Bond-Antitermite.pdf
025-Bond-FRP Door.pdf
026-Mix Design Condition-.pdf
027-Call before U Dig-Application Dt.27-3-2023.pdf
028-Pile Integrity Test Dt.06-04-2018.pdf
029-Priate Lab Testing Dt.25-02-2025.pdf
030-Security Deposit Releasing Dt.24-10-2017.pdf
031-Sign Board at Site Dt.17-08-2002.pdf
032-SOR Item Modification Dt.10-12-2020.pdf
033-Tender Re-invite guideline Dt.25-8-2015.pdf
034-RTGS PARIPATRA Dt.30-04-2018.pdf
035-GR-Other.pdf
036-GR-Other-1.pdf
037-GR Dt.17-3-2026.pdf
038-Performance Bond and Bitumen date (1).pdf
039-GR Dt.18-02-2017.pdf
040-Special Condition for Fire Fighting.pdf
042-DTP-Electrical works.pdf
041-Building-Specification Booklet.pdf
043-Drawing-1.pdf
044-Drawing-2.pdf
045-Drawing-3.pdf
046-Drawing-4.pdf
047-Drawing-5.pdf
048-Drawing-6.pdf
049-E Tender Notice-02 of 2026-2027.pdf
004-SBD Document (New Hostel Gujarat College).pdf
Download all tender documents and submit your bid