Addn/altn to bldg No. N-06 of adm area and Provn of 01xGents toilet block at Yol Cantt under AGE BR-II of GE (KH) YOL

Amount

SCHEDULE 'A' PART-I :- Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level), including removal of debris to a distance exc 1.5 km but n.exc 2 km, complete all as specified and as directed.

25mm thick Plain cement concrete 1:2:4 type B-0, nominal mix, using 12.5mm graded mechanically crushed stone aggregate over sub base, complete all as specified.

Vitrified ceramic tiles light shade, 10mm thick (Square/ rectangular) area of each tile not exc. 0.36 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand), complete, all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish of the premisses, complete, including removal of debris to a distance exc 1.5 km but n.exc 2 km, all as specified and as directed.

Granite (of any type) 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement(1:2) with admixture of pigment to match the shade of granite stone including grinding and mirror polishing complete as in kitchen platform, window cill /steps, jambs pillars etc. laid over and including 15mm thick screed bed in cement mortar (1:4), all as specified.

Glazed coloured tiles of size 350x250/450x350x7mm thick as in vertical surfaces such as jointed in neat cement slurry and pointed with coloured cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Dismantling plain or corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof covering, all as specified.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets in ceiling, all as specified.

Aluminium anodized snap grid frame work of size 605 mm x 605 mm as in false ceiling, flat or sloping (pattern as per manufacturer's catalogue/instruction), cutting holes for electrical fittings fixed on an including aluminium tee of size 25 mm x25 mm x1.5 mm as main runner, aluminium tee of size 25mmx25mmx1.25mm as cross runner and aluminium angle of size 25mmx25mmx1.25mm at the perimeter suspended from soffit at approx 900mm centre to centre with hangers 6mm dia galvanized (length as per site requirement) adjusting level fixed to roof by means of ceiling cleats made out of galvanized iron flat 40mmx3mm size, 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including necessary scaffolding all as specified and directed.

S&F 12mm thick gypsum board in ceiling fixed with screws as per manufacturer instructions, all as specified and directed.

Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately)

Preparation of newly ceiling board surfaces and applying two coats of oil emulsion distemper, complete, all as specified.

Dismantling timber scantlingsin over 40 sqcm in section, in framed work, complete all as specified.

2nd class soft wood (Kail) as in scantling clean sawn timber fixed in framed complete, all as specified.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe.290W Gde E-165, steel workcomplete, all as specified.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 30 cm long, diameter 16mm, complete all as speciied.

Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc. conforming to grade Fe.290-0.Gde-E-165, steel work, all as specified.

Mild Steel framed work as Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete, conforming to Fe 410 Gde E-250, all as specified.

Applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, all as specified.

Harrison 25mm bore Curtain rails, mild steel, chromium plated with fixing brackets, stops and roller etc. fixed in repair complete all as specified.

Demolition of stones or brick masonry, built in cement mortar including all quoins, arches etc., but excluding ashlar facing, dressed stone work etc.complete all as specified.

Fly ash brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified.

Brick work with old size fly ash bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 (1 cement : 4 coarse sand), all as specified.

Taking down cement plaster on brick or stone walls, ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc, including removal of debris to a distance exc 1.5 km but n.exc 2 km, complete all as specified and as directed.

Rendering cement plaster 15mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) on internal fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) on external fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement with WPC, all as specified. Note :- water proofing compound shall be measured and paid separately

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over 2mm thick wall care putty, complete, all as specified and as directed.

Preparation of newly plastered wall surfaces and applying two coats of cement base, complete, all as specified.

Bib taps, fancy type 15mm bore, cast copper alloy with crutch or butterfly handle, screwed down, chromium plated screwed for iron pipe or for brass ferrule and fixed in repair, all as specified

20mm bore Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions including 1 No. 20mm union cutting, threading existing GI pipe at a level of 1.8m, and fixed in repairs complete, all as specified.

15mm bore Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions including 1 No. 20mm union cutting, threading existing GI pipe at a level of 1.8m, and fixed in repairs complete, all as specified.

Sink with drainage board made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, including 40mm dia waste pipe & CP waste coupling, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, fixed in repair, all as specified.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement, dia of outlet 75mm, all as specified.

Steel plate rack of size 900mmx750mmx250mm made of stainless steel 1.00mm thick fixed over 40cm long MS angle of size 25x25x3mm- 02 Nos including bedding in cement mortar on to dwarf wall with screws ands PVC sleeve of required or fixing arrangement and fixed in repair, complete all as specified.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall of bore 110mm including fixing adjustable clamps complete, complete, all as specified.

PVC (SWR) bends any radius, 110mm bore jointed with solvent cement and (fitted with oval access door, all as specified.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall of bore 75mm including fixing adjustable clamps complete, complete, including taking up or down old pipe, all as specified.

Taking down existing tanks and removing to store water tanks of capacity n.exc 500 ltr, complete all as specified and directed.

Rotational moulded polyethylene water storage tank (three layered, cylinderical vertical with closed top) of capacity 500 Litres hoisted and fixed in position including ball brass valves, high pressure, with polythene float and flynut 20mm bore and making connections with existing water supply line, complete all as specified and directed.

Taking down existing tanks and removing to store water tanks of capacity n.exc 1000 ltr, complete all as specified and directed.

Rotational moulded polyethylene water storage tank (three layered, cylinderical vertical with closed top) of capacity 1000 Litres hoisted and fixed in position including ball brass valves, high pressure, with polythene float and flynut 20mm bore and making connections with existing water supply line, complete all as specified and directed.

PVC (SWR) bends any radius, 75mm bore jointed with solvent cement and fitted with oval access door fixed, all as specified.

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

Plain cement concrete M-15, nominal mix, B-0 using 12.5mm graded mechanically crushed stone aggregate as, in lintels upto 1.50 metres clear span cuts, steps seismic and other similar bends, coping, bands plates for serving hold fasts etc. and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as specified. Note :- (i) Reinforcement if any shall be measured and paid separately.

Taking down aluminium door/window shutter with frame, taking out servicable glass panes, hydraulic door clocer, but hinges, double action hydraulically regulated floor spring and other fittings, if required carefull and refixing in the same opening after repairs of unserviceable or loosened joints/cleats of top rail/bottom rails/lock rails and styles etc and fixing old serviceable glass, any thickness with rubber packing and aluminium beadings, fixing of old servicable hydraulic door closer, double action door spring duly oiling/greasing and fixing all servicable fitting complete all as directed by Engr-in-Charge.

Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing all as specified.

5mm thick PVC sheet fillet with 35mm for wall paneling inclusive of fixing on to wall to make PVC frame complete, all as specified and directed.

Natural colour 15 micron anodized aluminium door chowkhat with shutter of approved design complete with all fixing arrangements including providing and fixing door handles, tower bolts, hydraullic door closer and mortice lock, hinges, door stopper including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- (a) Shutter vertical member 85.00 x 44.45 x 1.80mm weighing 1.302 Kg/RM. (b) Shutter top member 83.5 x 44.45 x 1.70 mm weighing 1.243 Kg/RM. (c) Shutter bottom member 114.30 x 44.45 x 1.29mm weighing 1.139 Kg/RM. (d) Shutter lock rail 83.5x44.45x1.70mm weighing 1.243 Kg/RM. (e) Anodised aluminium handle, fancy type, 350mm long and aluminium tower bolt of size 150mm. (f) 5.50mm thick tinted sheet glass fixed with alumnium beading, silicon lining and gaskets. (g) Aluminium anodised frame of door of section 101.6 x 44.45 x 1.75mm weighing 1.367 Kg/M, with flat iron hold fasts and necessary concrete in PCC M-15, type B-1 using 12.5mm graded stone aggregate to fix hold fasts all as directed. Note:- (i) Shutter shall be fixed with heavy floor spring ISI marked and pivot, brass lock with duplicate keys.

Natural colour 15 micron anodized aluminium window/ventilator chowkhat with shutter of approved design complete with all fixing arrangements including providing and fixing door handles, tower bolts, hydraullic door closer and mortice lock, hinges, door stopper including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- (a) Shutter vertical member 47.62 x 45.45 x 1.74mm weighing 0.881Kg/RM. (b) Shutter top member 47.62 x 44.45 x 1.14 mm weighing 0.607 Kg/RM. (c) Shutter bottom member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (d) Natural colour 15 micron anodised aluminium anodised frame of chowkhat of section 85x44.45x1.80mm weighing 1.302 Kg/RM, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed. (e) 5.50mm thick tinted sheet glass fixed with alumnium beading, silicon lining and gaskets. (f) The size of Anodised aluminium round handle, fancy type shall be 100mm dia (02 Nos) and aluminium anodised aluminium tower bolt of size 100mm (02 Nos).

Natural colour 15 micron anodized aluminium sliding window three track with chowkhat and aluminium grill of approved design complete with all fixing arrangements including providing and fixing door handles, tower bolts and provision for fixing lock including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- (a) Shutter vertical member 47.62 x 45.45 x 1.74mm weighing 0.881Kg/RM. (b) Shutter top member 47.62 x 44.45 x 1.14 mm weighing 0.607 Kg/RM. (c) Shutter bottom member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (d) Natural colour 15 micron anodised aluminium anodised frame of chowkhat of section 85x44.45x1.80mm weighing 1.302 Kg/RM, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed. (e) 5.50mm thick tinted sheet glass fixed with alumnium beading, silicon lining and gaskets and stainless steel wire cloth. (f) The size of Anodised aluminium round handle, fancy type shall be 100mm dia (02 Nos) and aluminium anodised aluminium tower bolt of size 100mm (02 Nos).

S&F 9mm thick toughened glass shutters (single leaf openable type) with diamond polished edge, clear glass including all hardware fittings detailed as under, fixed in position as per manufacturers instructions including following fittings complete. (a) Stainless steel top patch (cat No. EPF-701) 01 set. (b) Stainless steel top pivot (cat No. EPF-712) 01 set. (c) Stainless steel bottom patch (cat No. EPF-702) 01 set. (d) Glass to wall stainless steel lock (cat No. FH-ECO-842) 01 set. (f) Stainless steel handle 300mm size (cat No. ESBH-011) 02 Nos for each shutter. Note:- Cat No mention above for hardware fittings are of make ENOX, contractor may use similar type hardware fittings of make DORMA/OZONE make of glass ATUL/MODI/GURD/SAINT GOBAIN/JINDAL/INDAL/HINDAL/WALCO.

Supply fabricate and fix in position aluminium partition wall with top, middle and bottom frame of size 101.6x44.45x1.75mm weighing 1.367 Kg/RM, partly glazed with 5.5mm thick tinted glass with or without sash bars and partly panelled with 9mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position. Note:- (i) section No given above are make jindal, contractor may use similar section of other make mention in appx 'c'.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each and removing from site, all as specified.

Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 85mm x 35mm double rebated comprises gauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC M-15, type B-0 (04 No's for each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including following fitting welded to frame shutter:- (i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window. (ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf. (iii) MS tower bolt 150mm long - 2 No per leaf. (iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf. (v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf. (vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf. (vii) Flat iron fillets of size 20X3 mm for fixing wire gauge. (viii) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 26/13. Make : As per Appendix 'C'.Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day.

Taking down shutters of any description exc. 1 Sqm not exc. 2 Sqm each and removing from site, all as specified.

Factory made 2nd class hard wood (Sal/ Hollock) plain, framed, panelled 35mm thick shutters with two panels and with interlocking rail and and panels of 9mm BWP commercial plywood or 12mm veneered particle with commercial face veneers on both sides.The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, all as specified.

Factory made second class hard wood (Sal) glazed and Skelton door shutters 35mm thick open rebated and prepared to receive glass gauge etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass or gauge etc., size of members of shutter as specified in clause 8.24 (a) of part-I, fitted to chowkats, complete all as specified.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 150mm, fixed, all as specified.

Extruded aluminium alloy handles, (ISI marked), fabricated type, anodised, of size 150mm, all as specified.

Butt hinges, (ISI marked), medium weight, cold rolled, stainless steel 100mm long, all as specified.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 250mm with lipping frame to match, all as specified.

Applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surfaces of any description, exc. 10cm width or girth including preparation of surfaces, all as specified.

Reinforced cement concrete (nominal mix) M-15, B-0 (using 12.5mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintel, over 1.50m span all as specified. complete all as specified. Note:- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement shall be measured and paid separately.

Reinforced cement concrete (nominal mix) M-15, B-0, (using 12.5mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts, all as specified. Note:- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement shall be measured and paid separately.

TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, all as specified.

TMT bars 5mm dia and over up to 10mm, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in stirrups, spacers and binders, all as specified.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. For fair finished flat surfaces of concrete, all as specified.

Plain cement concrete M-10 nominal mix, type C-1 using 20mm graded mechanically crushed stone aggregate as in surface channel and drains including necessary formwork, all as specified.

M&L for slate tiles best quality locally available fixed on wall with neat cement slurry/paste including rendering 15mm thick cement mortar 1:4 on stone masonary/brick masonary size and pattern to be laid as ordered by Engr-in-Charge.

Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads, all as specified.

Sheet glass 3mm thick ordinary quality and glazing with oil putty wooden beads in squares, not exc. 0.5sqm in each pane, complete all as specified.

Plain cement concrete M-7.5, nominal mix, type D-2, using 40mm graded mechanically crushed stone aggregate as in sub base, 75mm thick, surface finished even and fair to receive top surface, all as specified.

Chequered cement concrete tiles machine pressed of size 20cmx20cmx 25mm thick with grey cement, set jointed & pointed in neat cement slurry mixed with no pigment to match the shade of the slab in floors laid over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified.

Taking up or down 15mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.

Taking up or down 20mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.

Mild steel galvanized iron water tubing 15mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.

Mild steel galvanized iron water tubing 20mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor/ sunken floor spout complete, all as specified and directed.

Excavation in trenches not exc 1.5 metres wide and n.exc 1.5 metres deep and getting out in any type of soil, all as specified.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc.25cm thick each layer of soil all as specified.

Removing excavated material not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified.

Plain cement concrete M-7.5, nominal mix, D-2, using 40mm graded mechanically crushed stone aggregate as in foundation, filling and mass concrete, complete all as specified.

Reinforced cement concrete (design mix) M-25 (using 20mm graded crushed stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, all as specified.

Reinforced cement concrete (design mix) M-25 (using 20mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts, complete all as specified and directed.

Reinforced cement concrete (design mix) M-25 (using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintel, over 1.50m span, complete all as specified.

Reinforced cement concrete (design mix) M-25 (using 20mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), etc. For rough finished flat surfaces of concrete, all as specified.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for roughly finished flat surfaces of concrete, all as specified.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, for roughly finished flat surfaces of concrete, all as specified.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, for fair finished square, rectangular or polygonal surfaces of concrete, all as specified.

Hard core of broken stone or boulders of gauge not exc. 63mm deposited, spread and levelled in layers not exc. 15cm thick, watered and rammed to a true surface, all as specified.

Rendering cement plaster 10mm thick in cement mortar 1:3 (1 cement : 3 coarse sand) on ceiling, surface finished even and smooth without using extra cement, all as specified.

Three coats of white wash on newly plastered or previously undecorated surfaces of ceiling including preparation of surfaces complete, all as specified.

Plain cement concrete M-10, nominal mix, type C-2, using 40mm graded mechanically crushed stone aggregate, 75mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.18 Sqm but not exc. 0.38 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand) complete, all as specified.

Vitreous china wash down water closet (pedestal pattern) with flushing cistern (single piece), coloured of size 800mmx375mmx650mm including traps, trap distance 180mm connection to drain or outgoing pipe, flushing pipe, anti syphonage pipe complete including fittings, PVC coloured seat cover and CP jet including PVC connection, fixed complete and provision of PCC M-15, type B-1 using 20mm graded crushed stone aggregate, complete all as specified and directed. Make:- Cat Part No. ARS-WHT-39751P of jaquar or equivalent make in Appx 'C'.

S&F toilet paper holder with flap recessed type (stainless steel) of vitreous china fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed. Make:- Jaquar Cart Part No AHS-1553 or equivalent make in Appx 'C'.

Chromium plated (Health Faucet) (ABS Body) suitable for 15mm dia pipe, with 1.25 Meter Long flexible Tube & ABS Wall Hook, including making connections and fixed in position, complete all as specified. Make: Cat Part No. ALD-573 of Jaquar or equivalent in makes mentioned in Appendix 'C').

Urinal with sensor of jaquar with partition.

Rounding to edges of stone slabs of any type one edge, such as in steps cooking platform, cill of window and other simillar situations complete all as specified.

Wash basins, Vitreous China (under counter basin) size 485mmx395mmx150mm, coloured fixed in granite counter by making suitable holes, new brackets with and including cutting for and pinning on ends of brackets, 450mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and union for discharge pipe, waste, chain and plug and porcelain stopper, waste pipe of polythylene of low or high density or PVC of 32mm dia including 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed, complete all as specified.(Cat Part No JDS-WHT-25909 of 'Jaquar' or equivalent in makes mentioned in Appendix 'C').

Chromium plated Single Lever WHB center hole mixer with Popup Waste System, 450mm Long Braided Hoses complete, all as specified. Make:- (Cat Part No SOL-6051B of 'Jaquar' or equivalent in makes mentioned in Appendix 'C').

Soap dish, vitreous China white, approximate size 160x160x90mm, chromium plated, fixed to plugs with chromium plated, brass screws, all as specified.

Bottle trap of bore dia of discharge pipe 32mm of PTMT having minimum water seal of 25mm. (Minimum weight 32mm-260gms/40mm-270 gms).

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall of bore 75mm including fixing adjustable clamps complete, complete, all as specified.

PVC connection 15mm size with PTMT nuts at boths end 450mm long and fixed, all as specified.

PTMT Chromium Plated, tubular towel ring fixed with chromium plated screws, (Minimum weight of 90 gms) complete all as specified.

Stop/Angle valve, fancy type with wall flange, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed, complete, all as specified.

Angular Stop valve, cast copper alloy, fancy type chromium plated, with wall flange, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed. complete, all as specified.

Supply only liquid water proofing compound, complete all as specified.

Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) door shutter with frame, partly glazed with 5mm thick tinted glass and partly panelled with 9mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150mm size, aluminium barrel tower bolt 200mm size etc all as specified below complete all as specified and directed. (a) Frame (top & side) section shall of size 101.60 x 44.75 x 2.4mm (Section No 14021). (b) Vertical Members of shutter section shall be of size 85.00x44.45x2.00mm (section No 19560). (c) Top Members of shutter Section shall be of size 83.50 x 44.45 x 2.00mm (section No 19581). (d) Lock rail (Middle member) of shutter section shall be of size 150.00x44.45x3.00mm (section No 19596). (e) Bottom Members of shutter section shall be of size 150.00x44.45x3.10mm (section No 19584). (f) Glazing clip for securing glass of shutters shall be of 0.80mm thick (section No 19370). Note:- (i) Section No given above are of make jindal, contractor may use similar section of other make mention in Appx 'C' (ii) Floor door spring will be measured & paid separatlly

Aluminium (diecast) body door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, complete all as specified.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet and edges shall be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 180 of MES SSR 2020 Part-II

Factory made fully glazed PVC (frosted/ground/obscured) window/ventilator shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; completespecified and directed. Note:- Glass gauges inclusive of quoted rates.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5 mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1) specified and directed.

Extruded aluminium alloy handles, (ISI marked), fabricated type, anodised, of size 100mm, all as specified.

Butt hinges, (ISI marked), medium weight, cold rolled, stainless steel 75mm long, all as specified.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds etc. all as specified.

Rendering cement plaster 10mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (5mm thick first layers and 5mm thick 2nd layer), on fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified and directed.

Water profing treatement over terrace padding using SHALIURETHANE-BTD OF STP MAKE OR EQUIVALENT as approved by GE, high solid content single component water based liquid applied elastomeric water proofing membrene as ASTMC 836 and ASTMD 6083, thickness of the memberane shall be 1.5mm, having solid content of more than 80% elongation of 500+(-) 50% laid over reinforcing layer on non woven geo-textile mesh of 40/50 50gms, including applying self primer coat by diluting with 1:1 ratio @ 0.2 kg per sqm and suface preparation including cleaning of existing treatement complete all as per specified and directed by Engineer -in -Charge.

Surface excavation not exceeding 30cms deep and averaging 15cms deep and getting out in any type of soil, complete all as specified.

Machine pressed precast concrete interlocking paver block, any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigment laid over and including 50mm thick sand cushion, joints of tiles filled with dry sand and compacted with mechanical vibrator complete all as specified and directed.

Taking down point wiring with aluminium/ copper conductor for light point, fan & socket point/ power point etc. complete including light fiitings any type, switches, sockets, holders, (batten or pendent type), ceiling rose, switch board, bell/buzzer, bell push, tube light fitting, regulator etc. and making good to the disturbed surfaces of wall/ floor etc. to match with existing surfaces including white wash/ colour wash/ distempering to match with existing wall/ floor/ ceiling finishes and all as specified and directed.

Taking down sheet metal enclosure DB, MCB, main switch etc and making good distrubed surfaces to match with existing surfaces, complete all as specified.

Point wiring with 1.5 Sqmm copper conductor FRLS (Multi strand) PVC insulated ISI Marked unsheathed cable in and including concealed PVC conduit medium grade, ISI marked of suitable size with all fittings/ accessories and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FLRS as phase, neutral and earth wire connected to common earth dolly and including concealed pressed steel/ cast iron of suitable sizes terminal boxes made from 1.60 mm thick sheet for mounting of switches, sockets, fan regulators, light fittings etc. covered with 3mm thick plastic laminated sheet for one light point or one fan/exhaust fan point complete all as specified and directed. Note:-i) Wiring colour code i.e Red/Yellow/Blue for phase, Black for neutral and Green for earth shall be maintained. (ii) Rate of cutting chases, cement plaster, white wash and making surface good as existing surface included in quoted rate.

All as per serial item No '127' above, but for one 3 pin 5 Amps socket outlet on the same board with 2.5 sqmm PVC copper conductor cable and PVC insulated, unsheathed 2.5 sqmm stranded copper conductor cable as continous earth wire, all as specified and directed.

All as per serial item No '127' above, but for one 3 pin 5 Amps socket outlet on the independent board with 2.5 sqmm PVC copper conductor cable and PVC insulated, unsheathed 2.5 sqmm stranded copper conductor cable as continous earth wire, all as specified and directed.

All as per serial item No '133' above, but for 3 pin 15 amps socket out let on independent with 2.5 Sqmm PVC copper conductor cable and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified.

Supply and fix modular switch piano flush type one way 6 Amps, 1 module, 230V, Fixed complete all as specified.

Supply and fix modular switch piano flush type one way 16 Amps, 1 module, 230V, Fixed complete all as specified.

S&F Modular socket outlet 6 Amp 3 Pin, two module 230 Volts, Fixed complete all as specified.

S&F Modular socket 6/16 Amp 3 Pin, two module 230 Volts, Fixed complete all as specified.

S&F Modular electronic fan regulator flush type 120 Watt two module 230 volts, Fixed complete all as specified.

Ceiling rose, surface bakelite 65x50mm, three terminals, fixed, all as specified and directed.

Sheet metal enclosures factory made for DBs when MCBs to be used, single pole and neutral (double Door), 12 way, 240 volts with 200 Amp rated bus bar, all as specified.

M & L for vertical DB iron clad factory made TPN 4 Way, MCCB as incomer and MCB SP as out going, double door DB IP 43 protection level, incl Blanking plate, lugs etc complete and neutral link with one MCCB 4 pole 415V 100 Amps rating with rupture capacity 16KA incl connection, fixing flushed to wall, necessary grouting, making good with CM 1:4 and painted to match exisitng wall color, complete. (outgoing MCB will be measured seperately)

MCB SP 6 to 32 Amp, 240 Volts, 10 KA, C series including taking out old, all as specified.

MCB SPN 32 Amp, 240 Volts, 10 KA C series including taking out old, all as specified.

M & L for sub main wiring with two single core PVC insulated unsheathed, 1100 Volts grade, (FRLS) copper cable 6 sqmm stranded conductor and drawing through and including rigid PVC non metalic surface conduit medium duty (ISI Marked) with conduit accessories such as junction boxes, bends, tees etc. including continuous earth wire PVC insulated unsheathed 1100 volts grade, cable 6 sqmm copper conductor and connected to common earth dolly complete as directed including taking down old submain wiring. Note :-(i) One run of PVC conduit, two runs of cable (Phase + Neutral) and one run of earth wire shall be measured and paid as one unit.

Replacement of LED tube light fitting integral type ultra slim square profile LED lighting integral type fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack, 1x20 watt LED, 230V, and making connection with 2 core copper twisted flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete, all as specified and directed.

Supply and fixing in repair LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as required at site and directed by Engr - in - Charge.

S&F Basic decorative wall light, stainless steel, rust free fixture with glass diffuser suitable for 9W LED Lamp with E27 base complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size including dismantling of unserviceable tube light all as specified and directed.

M&L Replacement of LED bollard (garden light) of 10W with excellent light out put through its sleek PMMA window ensuring maximum illumination aspect in surrounding including PCC work for fixing of bollard light and making arrangement in PCC foundation for controlling of light and making electrical connection, complete all as specified and directed.

S&F for replacement of 2 way sheet metal enclosure (2 way SPN DB) with bus bar of suitable rating including making electrical connection with suitable size of lugs, complete all as specified and directed.

XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 10 Sqmm 2 core laid in trenches passing through pipe/ ducts/ surface of wall ceiling etc including testing after laying, making connection with suitable size of thimble, including taking out old cable, complete all as specified and directed.

Taking down ceiling fans//exhaust fan of 1200/250/300mm sweep of any make/ Model from fan hook/ wall dismentling blade opening of motor for overhauling/servicing, and then properly cleaning alll parts and greasing, oiling of bush & bearings after opening of the fan including reassembling and Painting of ceiling fans/exhaust fan after due preparation complete at site with super enamel synthetic white paint by spray gun including filling cavities with filler, one coat after cleaning all dust etc and writing MES No with black paint and than re-hanging and reconnecting of fan same or different location with new flexible cord of suitable size from ceiling rose to connector, and refixing with 2 core copper cable, complete all as directed by Engineer-in-Charge.

Material and labour for rewinding of ceiling fan of any make/model/sweep including removal of existing burnt winding carefully from slots, cleaning the slots throughly with suitable cleaing agent, applying slot inslation and rewinding with super enameled insulated copper wire of same gauge / same number of turns as existing and connecting the coil suitable to operate on 230VC, single phase, AC supply, permanent capacitor type, including all winding, insulating material and impregnation of insulating varnish as specified of any make, type, model and applying air drying the winding throughly including transportation from site of rewinding 1200/1400mm sweep, complete all as specified.

Taking down hot water storage heater (Geyser) of capacity 25 Ltr by disconnecting electric supply and water supply, replacement of siphon assembly, unsv parts and cleaning of tank etc and refixing at same or different location by grouting nut, bolts, washers and making electric and water connection and applying two coats of snthetic enamel paint (white or colour), testing, complete all as specified and directed by Engr-in-Charge.

S&F LED street light fitting 45W 230V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics, complete all as specified and directed.

Concealed Single pole and neutral sheet metal enclosure with a two pin and earth plug top and socket complete with one single pole MCB 20 Amps including taking out old, complete all as specified.

Replacement of motor suitable for plastic/mettalic body exhaust fan of size 200/250mm sweep and making necessary connection, complete all as specified and as directed.

Replacement of blade suitable for plastic/mettalic body exhaust fan of size 200/250mm sweep and making necessary connection complete all as specified and as directed.

Replacement of plastic/mettalic body suitable for exhaust fan of size 200/250mm sweep and making necessary connection complete all as specified and as directed.

Supply and replacement of louvers suitable for plastic/mettalic body exhaust fan of size 200/250mm sweep and making necessary connection complete all as specified and as directed.

S&F ON Load changeover switch of capacity 100 amps with enclosure for operating DG set operation, complete all as specified and directed.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230V, 1200mm sweep, five star rated with brushless direct current motor (BLDC), complete all as specified and directed.

XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 35 Sqmm 3.5 core laid in trenches passing through pipe/ ducts/ surface of wall ceiling etc including testing after laying, complete all as specified.

Sand cushioning to under ground cables, 8 cm thick layer before laying and testing the cable and 15 cm thick after laying and testing of the cable in trenches complete all as specified in Clause 19.75 of MES SSR 2020 Part-I and directed by Engr-in-Charge.

Sub class 'B' bricks old size, as cable protection cover, laid dry, flat, transversally along the length of cable, on sand cushioning, with width equal to the length of the brick, complete all as specified and directed.

M&L for 50mm dia GI pipe light grade as in trenches, across road or pole, complete all as specified and directed.

Replacement of Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of plate not less than 1.5m below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15 mm bore including provn of concrete pit in plain cement concrete M-20 type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of rainforced cement concrete M-20 reinforced with XPM (weight not less than 4 kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75m long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion. NOTE:- Item of earthing includes the cost of 7.5m long galvanised iron earth wire 4mm size and protection pipe of 15mm bore galvanised iron light grade and earth work.

Sheet metal enclosures factory made for DBs when MCBs to be used, single pole and neutral (double Door), 8 way, 240 volts with 200 Amp rated bus bar, all as specified.

MCB SP 6 to 40 Amp, 240 Volts, 10 KA, C series including taking out old, all as specified.

Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver all in one fxture, 1x20 watt LED and making connection with twin core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light including taking down old, complete, all as specified.

Endura Pearl 30W new generation energy saving and environmental friendly long life LED Bldg security light made up of pressure die case aluminium housing with high power LED as lighting source an lens enbedded PC cover having TOP opening seperate toughted glass/verminproof driver compartment, SPDs with IP66 protenction and impact resistancee of IK07 connecting with PVC insulated three core flexible copper conductor of suitable size from ceiling rose to fitting including bracket of suitable size, complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m, complete all as specified.

XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 16 Sqmm 2 core laid in trenches passing through pipe/ ducts/ surface of wall ceiling etc including testing after laying, complete all as specified.

Mild steel galvanised light grade 40mm dia tubing with all fitting; laid in trenches, across road or on pole complete all as specified.

Mild steel galvanized iron water tubing 25mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor, complete, all as specified and directed.

Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions and fixed, complete, all as specified.

M&L for cutting CI/GI pipe of 100mm dia in position for branch connection of new 25mm dia GI pipe, complete all as specified and directed.

SAFFRON CONSTRUCTION CO.