Addition & Alteration at Satymev Jayte Judicial Officers Quarters - D-1 Type 36 unit (P+9), E type 36 unit (P+9), E-1 type 32 unit (P+8), Total 104 Units at Gotri, Vadodara. (Implementation of Existing Fire Safety Systems and Equipment with Alarm System with all Fire Pumps & Other Misc. Fire Works)

Name of Work :- Addition & Alteration at “Satymev Jayte” Judicial Officers Quarters - D-

1 Type 36 unit (P+9), E type 36 unit (P+9), E-1 type 32 unit (P+8), Total 104 Units at

Gotri, Vadodara. (Implementation of Existing Fire Safety Systems and Equipment with

Alarm System with all Fire Pumps & Other Misc. Fire Works)

BILL OF QUANTITIES

Memorandum showing item of works to be carried out.

It. Item of Work Qty. Unit Rate in Amount

1 (A) Supplying, installation, testing and commissioning of Electric Driven 1.00 Set 332256.62

Main Fire Pump suitable for automatic operation and consisting of

following, complete in all respects, as required:

(B) Horizontal type, single Stage, centrifugal, End suction pump of cast iron

& bronze impeller with stainless steel shaft, Gland Pack conforming to IS

(C) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed

2900 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply

with IP 55 protection for enclosure, horizontal foot mounted type with Class-

'F' insulation, conforming to JS-325.

(D) M.S. fabricated Common base plate, coupling, coupling guard,

foundation bolts etc. as required.

(E) Suitable cement concrete foundation duly plastered with anti vibration

1620 LPM at 88 m Head

2 (A) Supplying, installation, testing and commissioning of Diesel Engine 1.00 Set 565125.81

Driven Fire Pump suitable for automatic operation and consisting of

following, complete in all respects, as required: (Diesel Driven Pump)

(B) Horizontal type, Single stage, centrifugal pump of cast of iron body and

bronze impeller with stainless steel shaft, mechanical seal conforming to IS

(C) Suitable HP, 1500/2300 RPM water cooled with radiator, diesel engine

conforming to relevant IS standard

complete with auto starting mechanism, 12 /24 volts electric starting

equipment, 125 Ltrs diesel tank, exhaust pipe extended up to 10 m outside

pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick

aluminium sheet cladding, residential silencer, instruments and protection

as per standard specification, stop solenoid for auto stop in the event of

fault with audio indications, painted with post office red colour etc. as

(D) M.S fabricated, common base plate, coupling, coupling guard,

foundation bolts etc. as required.

(E) Suitable cement concrete foundation duly plastered and with anti

vibration pads.

1620 LPM at 88 m head

3 (A) Supplying, installation, testing and commissioning of Electric Driven 1.00 Set 114841.28

Pressurisation Pump suitable for automatic operation and consisting of

following, complete in all respects, as required: (Jockey Pump)

(B) Horizontal type/Vertical Inline type, Single Stage/Multi Stage, centrifugal

End suction pump of cast iron body and bronze impeller with stainless steel

shaft, mechanical seal conforming to IS:

(C) Suitable HP squirrel cage induction motor TEFC type suitable for

operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of

protection for enclosure, horizontal foot mounted type with Class-'F'

insulation, conforming to IS:

(D) M.S. fabricated Common base plate, coupling, coupling guard,

foundation bolts etc. as required.

(E) Suitable cement concrete foundation duly plastered and

with anti vibration pads.

180 LPM at 88 m Head

It. Item of Work Qty. Unit Rate in Amount

4 Fabrication, Supply, Installation, testing & commissioning of Electrical 1.00 No. 401899.54

Control Panel of cubical construction, floor mounted type, fabricated out of

2mm thick CRCA sheet, compartmentalised with hinged lockable doors,

dust and vermin proof, powder coated of approved shade after 7 tank

treatment process, cable alley, inter connection with suitable size copper

conductor cable/solid copper strip, having switchgears and accessories,

mountings and internal

wiring, earth terminals, numbering etc. complete in all respect, suitable for

main fire pump. pressurisation pump & diesel pump set complete as per

CPWD specification with following in coming and Outgoings, suitable for

operation on 415V, 3 phase, 50Hz AC supply with enclosure protection

class IP 42 as required: for all suitable AMP fire pump and Disel Pump in

one cubical construction panel

400A. 50kA 4 Pole MCCB, lcs=100% Icu rating Digital Voltmeter 0-500 V

with selector switch Digital Ammeter (0-250A) with selector switch & CTs

etc. LED type RYB phase indicating lamps, ON, OFF, trip indicating lamps

Set of AL Bus Bar 500A

(Note: All outgoing feeders for pumps should have digital Ammeter with

selector switches, and LED type ON, OFF, trip indicating lamps)

MAIN FIRE PUMP (Hydrant & Sprinkler)

200 A, 50kA TPN MCCB, lcs=l00% lcu, with fully automatic Star/Delta

starter suitable for 75 HP pump with overload protection, current sensing

type single phase preventor complete with all accessories and internal

wiring required for automatic operation, selector switch for local/remote,

auto / manual /OFF operation.

Suitable TPN MCCB, lcs=l00% lcu, with fully automatic Star/Delta starter

suitable for 75 HP pump with overload protection, current sensing type

single phase preventor complete with all accessories and internal wiring

required for automatic operation, selector switch for local/remote,

auto/manual/OFF operation.

JOCKEY PUMP (Hydrant & Sprinkler)

100 A, 50kA TPN MCCB, lcs=100% lcu, with suitable HP fully automatic

Star/Delta starter with overload protection, current sensing type single

phase preventor complete with all accessories and internal wiring required

for automatic operation, selector switch for local/remote, auto / manual /

DIESEL ENGINE CONTROL

Control for diesel engine comprising -Automatic/Manual selector switch &

attempts starting device, timers and relays as required, push buttons,

start/stop in manual mode Indicating lamp for high/ Low Lub. Oil pressure,

High Water Temp and Engine on indication The required built in auto panel

suitable for operating with all electrical component & accessories with

necessary parts. The panel shall be operate for Two Main Electrical Pump,

Two Jockey Pump & One Diesel Pump for Hydrant System & Sprinkler

Automatic System with full requirements and accessories. All Pump shall

as per sufficient requirement for Auto Operation system built in auto panel.

All pump pannel push switch start & automatically all pumps starts. No

Hindrance occurred for starting of panel for starting of all auto pump as

directed by Engineer in charge.

5 Dismantling & Removing existing all old Fire Pump with adjoining fittings, 1.00 Job 45450.00

pannels & switches including removing existing wiring & cable & cable tray

etc. complete as per Eng in Charge

6 Supplying and installing following size of perforated Hot Dipped 8.00 Mtr. 687.31

Galvanised Iron cable tray (Galvanisation thickness not less than

microns) with perforation not more than 17.5%, in convenient sections,

joined with connectors, suspended from the ceiling with two numbers GI

Suspenders i/c base of suitable size GI angle, GI bolts & nuts, fastener etc

as required.150 mm width X 50 mm depth X 1.6 mm thickness

It. Item of Work Qty. Unit Rate in Amount

7 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand 8.00 Mtr. 990.31

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps

or in existing trench / pipe of following size of cables

(I) 3 1/2 core 240 Sq. mm( 120 Sq. mm 1/2 core)

- for panel main cable

8 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand 8.00 Mtr. 137.81

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps

or in existing trench / pipe of following size of cables.

(F) 3 core 25 Sq. mm

- for Electrical pumps cable

9 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand 8.00 Mtr. 90.73

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps

or in existing trench / pipe of following size of cables.

(F) 3 core 6 Sq. mm

- for Jockey pumps cable

10 Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 8.00 Mtr. 26.53

kv grade ISI marked copper wires of following size to be erected as

(d) 1.50 Sq.mm 2 core round PVC sheathed

11 Supplying and making end termination with brass compression gland and 2.00 No. 992.88

aluminium lugs for following size of PVC insulated and PVC sheathed /

XLPE aluminium conductor cable of 1.1 KV grade as required.

Double Compression gland for Main Supply 3.5C X 240 sq. mm (62mm)

12 Supplying and making end termination with brass compression gland and 2.00 No. 282.46

aluminium lugs for following size of PVC insulated and PVC sheathed /

XLPE aluminium conductor cable of 1.1 KV grade as required. Double

Compression gland for Main Pump 3 X 25 sq. mm (25mm)

13 Supplying and making end termination with brass compression gland and 4.00 No. 251.64

aluminium lugs for following size of PVC insulated and PVC sheathed /

XLPE aluminium conductor cable of 1.1 KV grade as required. Double

Compression gland for Jockey Pump 2 or 3C X 6 sq. mm (19mm)

14a Providing, laying, testing & commissioning of 'B' class Medium duty G.l. 380.00 Mtr. 608.57

pipe conforming to IS 1239 including welding, fittings like elbows, tees,

flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall

ceiling with suitable clamp/support frame and painting with two or more

coats of synthetic enamel paint of required shade complete as required

14b Providing, laying, testing & commissioning of 'B' class Medium duty G.l. 60.00 Mtr. 671.91

pipe conforming to IS 1239 including welding, fittings like elbows, tees,

flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall

ceiling with suitable clamp/support frame and painting with two or more

coats of synthetic enamel paint of required shade complete as required.

14c Providing, laying, testing & commissioning of 'B' class Medium duty G.l. 45.00 Mtr. 826.83

pipe conforming to IS 1239 including welding, fittings like elbows, tees,

flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall

ceiling with suitable clamp/support frame and painting with two or more

coats of synthetic enamel paint of required shade complete as required.

14d Providing, laying, testing & commissioning of 'B' class Medium duty G.l. 90.00 Mtr. 912.42

pipe conforming to IS 1239 including welding, fittings like elbows, tees,

flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall

ceiling with suitable clamp/support frame and painting with two or more

coats of synthetic enamel paint of required shade complete as required.

It. Item of Work Qty. Unit Rate in Amount

14e Providing, laying, testing & commissioning of 'B' class Medium duty G.l. 30.00 Mtr. 1138.39

pipe conforming to IS 1239 including welding, fittings like elbows, tees,

flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall

ceiling with suitable clamp/support frame and painting with two or more

coats of synthetic enamel paint of required shade complete as required.

14f Providing, laying, testing & commissioning of 'B' class Medium duty G.l. 130.00 Mtr. 1295.88

pipe conforming to IS 1239 including welding, fittings like elbows, tees,

flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall

ceiling with suitable clamp/support frame and painting with two or more

coats of synthetic enamel paint of required shade complete as required.

14g Providing, laying, testing & commissioning of 'B' class Medium duty G.l. 235.00 Mtr. 1647.67

pipe conforming to IS 1239 including welding, fittings like elbows, tees,

flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall

ceiling with suitable clamp/support frame and painting with two or more

coats of synthetic enamel paint of required shade complete as required.

14h Providing, laying, testing & commissioning of 'B' class Medium duty G.l. 470.00 Mtr. 2253.67

pipe conforming to IS 1239 including welding, fittings like elbows, tees,

flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall

ceiling with suitable clamp/support frame and painting with two or more

coats of synthetic enamel paint of required shade complete as required.

14i Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe 6.00 Mtr. 5666.27

conforming to IS 1239/Class -II of IS: 3589 including Welding, fittings like

elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on

the wall/ceiling with suitable clamp/support frame and painting with two or

more coats of synthetic enamel paint of required shade complete as

required : 200mm

15a Providing laying, testing & commissioning of 'B' class Medium duty GI Pipe 40.00 Mtr. 4368.68

conforming to IS 1239/Class -II of IS: 3589 i/c fittings like elbows, tees,

flanges, tapers, nuts bolts, gaskets etc. in ground including welding &

providing, anticorrosive treatment with coal tar/asphalt tape as per IS

10221, etc. of following sizes complete as required. 150mm

15b Providing laying, testing & commissioning of 'B' class Medium duty GI Pipe 40.00 Mtr. 3028.76

conforming to IS 1239/Class -II of IS: 3589 i/c fittings like elbows, tees,

flanges, tapers, nuts bolts, gaskets etc. in ground including welding &

providing, anticorrosive treatment with coal tar/asphalt tape as per IS

10221, etc. of following sizes complete as required. 100mm

16a Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 1.00 Each 3521.31

rating with bronze/gunmetal/SS seat duly ISI marked complete with nuts,

bolts, washers, gaskets conforming to IS: 13095 of following sizes as

required: 50 mm dia

16b Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 3.00 Each 4033.15

rating with bronze/gunmetal/SS seat duly ISI marked complete with nuts,

bolts, washers, gaskets conforming to IS: 13095 of following sizes as

required: 65 mm dia

16c Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 7.00 Each 4627.17

rating with bronze/gunmetal/SS seat duly ISI marked complete with nuts,

bolts, washers, gaskets conforming to IS: 13095 of following sizes as

required: 80 mm dia

16d Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 8.00 Each 6223.48

rating with bronze/gunmetal/SS seat duly ISI marked complete with nuts,

bolts, washers, gaskets conforming to IS: 13095 of following sizes as

required: 100 mm dia

16e Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 7.00 Each 8334.21

rating with bronze/gunmetal/SS seat duly ISI marked complete with nuts,

bolts, washers, gaskets conforming to IS: 13095 of following sizes as

required: 150 mm dia

16f Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 1.00 Each 13907.19

rating with bronze/gunmetal/SS seat duly ISI marked complete with nuts,

bolts, washers, gaskets conforming to IS: 13095 of following sizes as

required: 200 mm dia

It. Item of Work Qty. Unit Rate in Amount

17a Providing, installation, testing and commissioning of non-return valve of 1.00 Each 5355.57

following sizes confirming to IS: 5312 complete with rubber gasket, GI

bolts, nuts, washers etc.as required: 50 mm dia

17b Providing, installation, testing and commissioning of non-return valve of 1.00 Each 7065.72

following sizes confirming to IS: 5312 complete with rubber gasket, GI

bolts, nuts, washers etc.as required: 80 mm dia

17c Providing, installation, testing and commissioning of non-return valve of 6.00 Each 10145.36

following sizes confirming to IS: 5312 complete with rubber gasket, GI

bolts, nuts, washers etc.as required: 100 mm dia

17d Providing, installation, testing and commissioning of non-return valve of 4.00 Each 16163.42

following sizes confirming to IS: 5312 complete with rubber gasket, GI

bolts, nuts, washers etc.as required: 150 mm dia

17e Providing, installation, testing and commissioning of non-return valve of 1.00 Each 26444.88

following sizes confirming to IS: 5312 complete with rubber gasket, GI

bolts, nuts, washers etc.as required: 200 mm dia

18 Providing, installation, testing and commissioning of stainless steel Y- 1.00 Each 20175.18

strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet

with 3 mm dia holes with stainless steel flange. 200mm dia

19 Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1.00 Each 16606.80

1200 mm in height with air release valve on top and flanged connection to

riser, drain arrangement with 25 mm dia gun metal wheel valve with

required accessories, pressure gauge and painting with synthetic enamel

paint of approved shade as required.

20a Supply , Installation, Testing , commissioning of Flexible Coupling (Rubber 2.00 Each 15655.00

Single Bellow) in pump discharge as specified and shown in drawing with

all accessories like flanges, nuts, bolts, etc. required for complete

installation. Installation shall be as per Technical Manual of manufacturer

and shall be as directed by engineer in charge. PN Rating : 20 -150mm NB

20b Supply , Installation, Testing , commissioning of Flexible Coupling (Rubber 2.00 Each 10605.00

Single Bellow) in pump discharge as specified and shown in drawing with

all accessories like flanges, nuts, bolts, etc. required for complete

installation. Installation shall be as per Technical Manual of manufacturer

and shall be as directed by engineer in charge. PN Rating : 20 -100mm NB

21 Providing and Fixing 25 mm dia. Air valve of Raising Main Line. For 6.00 Each 970.72

Air Release including supply, installing, testing and commissioning

etc. complete as directed by Engineer in charge.

22 S. I. T. C. in position approved make Forged Brass Ball valves having 56.00 Each 879.04

Body, Ball & stem bonnet in forged brass. Lever, washer & Nut in Carbon

steel. Gland packing & body seat ring in PTFE (Teflon) seal with female

BSP threads. Tested to a pressure not less than 20Kg/Sq.cm with all

accessories etc. Complete as per direction of the Engineer-in-

Charge.25mm Dia

23 Providing and fixing inspectors test assembly complete with test valve, 3.00 Each 5797.40

sight glass sectional drain valve, union with corrosion resistant orifice all

complete strictly as per drawing and standard. UL Approved. Complete

assembly in one Valve.25mm Dia

24 Providing and fixing Flow Switch in following size M.S./ GI Pipeline 3.00 Each 6906.52

including connection as required. 100 mm dia.

25 Supplying installing testing & commissioning of 100 mm dia. Pressure 8.00 Each 1801.78

Gauge 1% Accuracy direct bottom 3/8" BSP connection in brass socket &

Range 0 to 16 Kg/Cm2 etc. necessary as directed by Engineer in Charge.

26 Providing and Installation SS 304 male to male siphone tube size 8.00 Each 1150.03

3/8 inch dia for pressure gauge.

27 Providing and Fixing pressure switch in M.S./GI Pipe line including 3.00 Each 1429.41

connection etc. as required.

28 Providing and Installation SS 304 male to male siphone tube size 3.00 Each 1150.03

1/4 inch dia for pressure switch.

29 Providing and Fixing 8/10 mm dia G.I. Threaded Rod with Chilly clamp 240.00 Each 95.23

including fixing to ceiling slab at any height with standard bullet/anchor

fastener and nut-bolts for hanging of fire G.l. pipe line of any size with all

labour and materials as directed by Engineer in charge.

It. Item of Work Qty. Unit Rate in Amount

30 Structural steel work in single section, fixed with or without connecting 1550.00 Kgs 100.44

plate, including cutting, hoisting, fixing in position and applying a priming

coat of approved steel primer all complete.

31 Supply Installation Testing and commissioning of Zincalvalume sheet 75000.00 Ltr 9.22

Modular tank having size required size with gross volume of Tank is 100 KL

and Effective Volume is 75 KL. Rates are including of supply and erection

of required Fittings & accessories like Internal & External Ladder, Level

indicators, Air Vent, Manhole, Food Grade Liner & roof Railing as per

manufacturing standard with required Nozzles for Supply and discharge of

Fire water as per site situation and as directed by EIC.

32 Supply, installation, testing and commissioning of Gun-Metal Draw out 1.00 Each 10605.00

connection for Fire Brigade connection consisting of 63 mm dia

instantaneous type male coupling with built-in check valves and 100 mm

dia. flanged outlet complete with bolts, nuts and rubber insertions as

required as per IS:904-1983.

33 2 Way FB 3.00 Each 6215.78

34 4 Way FB 1.00 Each 12684.92

35 Supplying and fixing single headed internal hydrant valve with 45.00 Each 5676.54

instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast

iron wheel ISI marked conforming to IS 5290 (Type -A) with blank

Gunmetal/Stainless Steel cap and chain as required: Single Headed

Stainless Steel

36 Supplying & fixing 63 mm dia. Stainless Steel (Grade 304) short branch 45.00 Each 2911.88

pipe with 20 mm nominal internal diameter size nozzle conforming , to

IS:903 suitable for instantaneous connection to interconnect hose pipe

coupling as required: (18.18.2) Stainless Steel (Grade 304)

37 Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia 90.00 Each 3994.64

male and female couplings duly bound with GI wire, rivets etc. conforming

to IS 636 (type-A) as required: (18.16.2) Stainless Steel (Grade 304)

38 Supply Installing Testing & Commissioning of M. S. 18 guage hose box to 45.00 Each 4455.86

accommodate of 2-Nos 15-Mtrs. Length Hose Box pipe & 1 No. of branch

pipe with Nozzle, With necessary fabrication support and joints and 3 mm

glass shutter including powder coating etc. complete as directed by

engineer in charge.

39 Supplying and fixing first-aid Hose Reel with MS construction spray painted 45.00 Each 8080.00

in post . office red, conforming to IS 884 complete with the following as

required. 20/25 mm nominal internal dia water hose thermoplastic (Textile

reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal

globe valve & nozzle. Drum and brackets for fixing the equipment on wall.

Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe

40 Supplying & fixing 6 Kg. Capacity ABC Dry Chemical powder Stored 39.00 Each 2828.00

Pressure type fire Extinguisher As per I.S-15683 having ISI marked Etc.

complete as Directed by EIC

41 Supply & installation ISI marked (IS:15683) Fire Extinguisher, Carbon-di- 39.00 Each 4545.00

oxide type capacity 4.5 Kgs. flat base including valve, discharge hose

of not less than 10mm dia., 1M long and complete in all respects

including initial fill with CO2 gas conforming to IS:307-1966 filled to a

filling rate of not more than 0.667 and wall suspension bracket. (LMR) etc

completed as directed EIC.

42a Providing, Fixing, testing & Commissioning of 15 mm dia quartzoid 180.00 Each 512.70

bulb type sprinklers of rating 68 degree centigrade with required

accessories: (a) Pendent Sprinkler 68o C

42b Providing, Fixing, testing & Commissioning of 15 mm dia quartzoid 3.00 Each 598.30

bulb type sprinklers of rating 68 degree centigrade with required

accessories: Side Wall Sprinkler

43 Providing and Fixing Remote Push Button Switch for Main Fire Pump on All 30.00 Each 2139.83

floors for operation of Fire Pump including control wiring 3 core x

Sq.mm copper armoured with all required fittings and accessories with all

labour and materials as directed by Engineer in charge.

It. Item of Work Qty. Unit Rate in Amount

44 INTELLIGENT FIRE ALARM SYSTEM 4.00 Each 11357.36

Supplying, installation, testing and commissioning of Sector panel Suitable

for 1 Zone Complete with visual indication for short circuit fault , open

Circuit fault, fire condition and all other standard facility as per IS :

with mimic diagram for all area / zone covered with all connection,

interconnection required. 6 Zone

45 Supplying, installation, testing & commissioning of addressable manual call 30.00 Each 3477.65

point complete as required.

46 Supplying, installation, testing & commissioning of addressable horn cum 30.00 Each 3151.54

strobe complete as required.

47 Providing, Fixing & installation PVC 100x100mm junction box for 30.00 Each 118.12

smoke detector including fixing in ceiling with all labour & materials

as directed by engineer in charge.

48 Installation control valve assembly Supply, installation, testing and 3.00 Each 30300.00

commissioning of UL/FM Approved installation control valve assembly with

vertical wet alarm valve with hydraulic alarm motor gong , 2 nos pressure

gauges, test valves 50 mm drain valves with all necessary accessories.

49 Supplying & laying of 2x1.5 Sq.M. fire alarm armoured cable, 600/1000V 130.00 Mtr 164.34

rated with annealed copper conductor having XLPE insulation, steel wire

armouring & FRLS/HFFR outer sheath complete as required.

50 Design, Supply & Installation of Safety Signage approved make made of 156725.00 Sq.C 2.53

zinc sulphide based glow in the dark rigid sheet with high luminous M

property enclosed in a transparent weather proof U/V stabilized

plastic pasted on 3mm thick Foam sheet for making signage For

All Floor etc. completed as directed by engineer in charge.

51 Providing & Fixing Flange End Connection of Dia 25mm to 150mm dia 26.00 Each 641.95

including rubber Gasket and suitable Nut bolts as required and as directed

52 Supplying & Installation of fire blanket of Standard manufacturer for 1.00 Each 3585.50

protection of fire at the time of fabrication & welding work as & where

required as per directed by EIC.

53 Dismantling & Removing of existing fire fighting equipment i.e. Hydrant 81.00 Each 252.50

Valve, Hose Box, Isolation Valves, Hose reel drum etc with all fitting

included with cutting in wall/ ceiling etc. with all labour and handed over to

the client store as directed by Engineer in charge.

54 Providing and fixing of Anchoring of 16mm dia MS bar in ground with MS 100.00 Mtr 176.75

Plate of size 150 x 150mm ( 2.5mtr Centre to centre ) including welding as

required for supporting fire G I Pipe line of any dia. as per EIC.

55 labour charges for dismantling existing PCC of any Grade with Electrical 10.00 Mtr 707.00

Heavey Duty breaker m/c with needle as per EIC

56 Cutting hole by mechanical means of 25 to 150 mm dia (or more as 10.00 Each 414.10

per site situation) in slab / beam throughout the thickness including

finishing the same with cement mortar 1:3 as directed by Engineer in

57 Demolition including stacking of serviceable materials and 17.10 Cum 1084.30

disposal of unserviceable materials with all lead and lift.[I] Reinforced

Cement Concrete work.

58 Dismantling tiled / paver block or stone floors laid in mortar including 15.90 Sqm 48.91

stacking of serviceable materials and disposal of unserviceable

materials with all lead and lift.

59 Excavation for foundation up to 1.5 m depth including sorting out and 23.08 Cum 120.01

stacking of useful materials and disposing off the excavated stuff up to

Meter lead.(A) Loose or soft Soil

60 Providing and laying cement concrete 1:2:4 (1- Cement : 2 Coarse sand : 4- 5.77 Cum 3656.13

graded stone aggregates 20 mm nominal size) and curing complete

excluding cost of formwork in (A) Foundation and Plinth

It. Item of Work Qty. Unit Rate in Amount

61 Providing and fixing pre-cast Rubber Dye /steel Dye inter locking concrete 15.90 Smt 704.07

block 60mm thick with grade of concrete M300 pneumatic compressed /

vibrated mechanically and as per approved design Confirming

to IS 15658 : 2006 including 35 mm Sand layer for levelling and

filling the joint with sand in proper line and level as per guidelines of IRC :

SP 63-2018 etc. Complete.

62 Filling in plinth with sand under floors including watering ramming, 1.92 Cum 471.69

consolidating and dressing complete.

63 Supplying and Laying, Spreading and Compacting of hard stone of 5.77 Cum 1558.43

following nominal size including carriage of material spreading in uniform

layers manually on prepared base and compacted consolidation using

to 63mm size BT metal and 25% sand for binding material, labours etc.

completed as directed Engineer in Charge.

64 Providing and Laying ordinary cement concrete 1:1:2 (1 Cement : 1- coarse 11.54 Cum 4407.64

sand : 2- graded stone aggregates 20 mm nominal size) and finishing

smooth with curing etc. complete including the cost of formwork but

excluding the cost of reinforcement for R.C.C work in (i) Mass Concrete

65 Providing formwork of ordinary timber planking so as to give a rough finish 38.47 Smt 179.36

including centering shuttering strutting and propping etc. Height of propping

and centering below supporting floor to ceiling not exceeding 4 M. and

removal of the same for in situ reinforced concrete and plain concrete work

in. (A) Foundations Footings Bases of Columns etc. and Mass concrete.

66 Providing TMT Bar FE 500D reinforcement for R.C.C. work including 990.00 Kgs 77.29

bending, binding and placing in position complete up to floor two level

67 Providing 10mm th. Cement Plaster in single coat on brick / concrete wall 12.00 Smt 129.14

for interior plastering up to floor 2 level and finish even & smooth in (iii )

cement mortar 1:6 ( 1 cement :6 sand )

68 Brick work using common burnt clay building bricks having crushing 1.29 Cum 4121.53

strength not less then 35 kg/cm in foundation & Plinth in cement mortar 1:6

( 1 cement : 6 Sand ) ( B ) conventional

69 Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe 16.00 Rmt 195.67

( SCH- 40) for cold water including fittings make PRINCE / SUPREME /

ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp at every two metre

C/C or shall be concealed as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

70 Providing and fixing UPVC check or non-return full way valve.(E) 50mm 4.00 No 422.18

i.e. Rupees Eighty One lakh One thousand Seventy Five and paise Forty Seven only.

I/We am/are willing to carry out Deputy Executive

the work Divisional

@ _______ __ Accountants Officer

% above/below Executive

percent (Should be written

in figures and words) of the estimated rate mentioned above. Amount of my /our tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-

Charge for which no extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills.

It. Item of Work Qty. Unit Rate in Amount

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C, Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is

a change as per actual mix design the cost of difference of cement consumption have been deducted from the

rate of original item at the rate of input rate mentioned in all the tender.

5. The Contractor will have to submit the all required mix design at his own cost before execution as directed and to

be approved from the Engineer in charge.

6. All item rates considered in the tender are inclusive of execution at all floor levels, including all leads and

7. Credit for dismantled materials of amount of Rs. 1,50,000.00 must be recovered from 1st R.A. bill of

Above all items of "BoQ" with Item Description, Unit, Rate & Amount have verified by me and found

Deputy Executive Engineer Sr. Divisional Account Officer Executive Engineer

Multistorey Building Sub Division, City (R & B) Division, City (R & B) Division,

Vadodara Vadodara Vadodara