GENERAL PWD Roads Section office Muttom Cabin works in PWD Roads Section office Muttom at PWD Complex Thodupuzha

Amount

Cabin works

OD292938/2024-2025:Providing and fixing Pre-laminated high density fibre board, with both sides decorative lamination other side balancing lamination Grade-I (exterior grade) in cabin/shelves with screws and fittings wherever required, edges to be sealed with PVC edge banding tape 2.00 mm thick of approved brand (fittings to be paid separately). Pre-laminated with decorative lamination both side exterior Grade-I HDF Board 16mm thick confirming to IS:14587.

OD126362/2023-2024:Providing and fixing auto- concealed hydraulic soft closing hinges 116x60 mm etc... complete.

OD126363/2023-2024:Providing and fixing 12mm glass shield for cabin and computer tables as per direction / Providing and fixing 12mm thick frameless toughened glass of approved brand and manufacture, including providing and fixing two side fixing clamp arrangement and making necessary holes etc... for fixing required glass fittings, all complete as per direction of Engineer-in-charge.

OD126364/2023-2024:Supplying and providing in position etching sticker as per the design and drawing including cost and conveyance of all materials, labour charges etc complete.

9.79.2:Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete.50 mm

9.81.2:Providing and fixing bright finished brass handles with screws etc. complete:100 mm

9.115:providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineer -in-charge.

OD126365/2023-2024:Providing and fixing powder coated telescopic drawer channels 450mm long with necessary screws etc... complete as per the direction of Engineer in charge.

OD126711/2023-2024:Engaging carpenter for repair works

21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2:For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.2.2:Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides

9.46.2:Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete:20 mm dia

OD297973/2024-2025:Supplying and stitching curtain cloth and fixing position as per the direction in charge. Measurements to be taken for clear opening width.

OD298098/2024-2025: Supplying Hi power hi back executive chair as per the direction of Engineer in charge.

Tomy (BID ID -2178061)

Bidder Name

Jayesh M