CONSTRUCTION OF ONE GUARD ROOM WITH ATTACHED TOILET WITH BRICK WALLS CGI SHEET ROOFING FALCE CEILING ELECTRIFICATION PAINTING WATER SUPPLY WITH PVC OVER HEAD STORAGE TANK PROVISION NEAR EXISTING OBSERAVTION POST NO 02

DETAILS OF WORK

Earth work in excavation by mechanical means (Hydraulic excavator) manual means in foundation trenches or drains not exceeding 1.5 m in width or 10 sqm on plan including dressing of sides and ramming of bottoms, lift upto 1.5m including getting out the excavated soil and disposal of surplus excavated soil as directed, with in a lead of 50 m. All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:3:6 ( 1 cement:03 coarse sand and 6 graded stone aggregate 40mm nomial size)

Centering and shuttering including strutting, propping etc and removal of form work for Foundations, footings, bases for comuns.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, cosolidation each deposited layer by ramming and watering lead up to 50 m and lift upto 1.5 m

Brick work with common burnt clay F.P.S non modular bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in cement mortar 1:6 (1 cement 6 coarse sand)

Cement plaster in fine sand 12 mm cement plaster of mix 1:6 (1 cement : 6 fine sand)

15 mm cement plaster on the rought side of single or half brick wall of mix 1:6 (1 cement : 6 fine sand)

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms per litre, of approved manufacturer, of required shade and colour complete, as per manufacture's specification. Two or more coats on new work.

Finishing walls with Acrylic Smooth exterior paint of required shade New work Two or more coat applied at the rate 1.67 ltr per 10 sqm over and including priming coat of exterior primer applied at the rate 2.20 kg per 10 sqm

Provided corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complet (up to any pitch in horizontal/vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63mm thick with zinc coating not less that 275 gm per meter square.

Steel work in built up tubular (round, square or rectangualar hollow tubes etc.) trusses etc, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc complete. Hot finished welded type tubes (Hollow section 50x30x2.5mm used for truss and 40x30x2.5 mm for purlines

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastner, including fixing or necessary butt hinges and screws and applyng a priming coat of approved ssteel primer, all complete as per the direction of Engineer in Charge

Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS:14616 and TADS 15:2001 (Part B) fixing with butt hinges of required size with necessary screws, all complete as per directions of Engineer in charge and paanelling with panels of 12 mm thick plain grade 1 medium density flat pressed three layer particle board FPT-1 or graded wood particle board FPT-1, IS 3087 marked, bonded with BWP type synthetic resin adhesive as per IS: 848 sqm

Providing and fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes

Electrification work for point wiring with 2 sq. mm and earth wire of 2 sq mm both are of ISI mark 1.1 kv grade FRLS PVC insulated multistandard of cooper and providing and fixing difference types of lights with switches and socket and ceiling fans complete as per direction.

M/S KAY KAY SALES