Construction of 8 Nos. Type-IV Quarters building at Govt. Polytechnical college in Tehsil Jaisinghpur Distt. Kangra (HP)

Amount

Excavation in foundation and trenches in all heights and depths and in all kinds of soil including saturated soils comprising of pick work, jumper work, pick jumper work, blasting work both in soft and hard rock, chiseling / wedging out of rock (Where blasting is prohibited) or any other mixed variety of soil including shoring, strutting, de-watering and pumping or bailing out water (surface and sub soil water) up to any heights / depths or any quantum of water including slush which may arise during de-watering, removal of slush and stacking the serviceable and un-serviceable material clear from the edges of excavation and then returning the stacked soil in 15cm (fifteen centimeter) layers where required into plinth and side of foundation etcetera, consolidating each deposited layer by ramming & watering and then disposing of all surplus un-serviceable excavated earth as directed within all leads and lifts, by head-load, mechanical transportation or by any other mode of transportation with all cost of labours, machineries and disposed of material to be neatly dressed and leveled as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Foundation, footings basis of columns etcetera and mass concrete as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centring, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Flat surfaces such as soffits of suspended floors, roofs, landings and the like floor etcetera upto any thickness as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Beams, cantilever, girders and lintels. Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto all depth and in all heights from floor as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Columns, pillars, posts and struts square rectangular or polygonal in plan as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Stair cases with sloping or stepped soffits excluding landing, as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Edges of slabs and breaks in floors and walls up to all width and heights as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Vertical surfaces such as walls (any thickness) partitions and the like including attached pilasters, buttresses, plinth and string courses and as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated plain cement concrete 1:4:8 (one cement is to four sand is to eight graded crushed stone aggregate 40 mm (forty millimeter) nominal size) and curing complete excluding the cost of form work in foundation and plinth as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Stone filling with hard stone of approved quality dry hand packed tightly under floor. as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying plain cement concrete grade M-20 (M-twenty) design mix to obtained the minimum compressive strength of 20N /mm2 (Twenty newton per square millimeter) with cement contents not less than 330 kgs (three hundred thirty kilogram) per cubic metre to give an even smooth surface mechanically mixed and vibrated & curing complete excluding cost of form work in foundation and plinth as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M-twenty) design mix to obtained the minimum compressive strength of 20N /mm2 (Twenty newton per square millimeter) with cement contents not less than 330 kgs (three hundred thirty kilogram) per cubic metre to give an even smooth surface mechanically mixed and vibrated including curing complete excluding cost of form work and reinforcement for reinforced concrete work in Foundation footings, bases of columns and the like and mass concrete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 ( M-twenty) design mix to obtained the minimum compressive strength of 20N /mm2 (Twenty newton per square millimeter) with cement contents not less than 320 kg (three hundred twenty kilogram) per cubic metre to give an even smooth surface mechanically mixed and vibrated including curing complete excluding cost of form work and reinforcement for reinforced concrete work in suspended floor ,roofs , landings , shelves and their supports balconies, beams ,girders , bressumers and cantilevers up to all floor level as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 design mix to obtained the minimum compressive strength of 20N /mm2 (Twenty Newton per square millimeter) with cement contents not less than 320 kgs (three hundred twenty kilogram) per cubic metre to give an even smooth surface mechanically mixed and vibrated including curing complete excluding cost of form work and reinforcement for reinforced concrete work in columns ,pillars, post, struts and the like and mass concrete up to all floor level, as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 ( M-twenty) design mix to obtained the minimum Compressive strength of 20N /mm2 (Twenty Newton per square millimeter) with cement contents not less than 320 kg (three hundred twenty kilogram) per cubic metre to give an even smooth surface mechanically mixed and vibrated including curing complete excluding cost of form work and reinforcement for reinforced concrete work in stair case (except spiral stair cases) including landings etcetera up to floor all levels as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 ( M-twenty) design mix to obtained the minimum compressive strength of 20N /mm2 (Twenty Newton per square millimeter) with cement contents not less than 320 kg (three hundred twenty kilogram) per cubic metre to give an even smooth surface mechanically mixed and vibrated including curing complete including cost of form work but excluding reinforcement for reinforced concrete work moulding as in cornices windows, sills etcetera exceeding upto any girth, upto floor all level as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the minimum compressive strength of 20 N/ mm2 (Twenty Newton per square millimeter) with cement contents not less than of 320 kg (Three hundred twenty kilogram) per cubic metre, mechanically mixed and vibrated including curing complete for reinforced concrete work in Chhajjas not exceeding 10cm (ten centimeters) thickness upto floor all levels including finishing the exposed surface with cement mortar 1:3 (One cement : Three sand) to give a smooth and even surface including centering/ form work and curing complete but excluding the cost of reinforcement for reinforced concrete work up to all floors level as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete M-20 ( M- twenty) design mix to obtain the minimum compressive strength of 20N/mm2 (Twenty Newton per square millimeter) with cement contents not less then 320 Kg (three hundred twenty kilogram) per cubic metre and curing complete excluding cost of form work and reinforcement for reinforced concrete work in walls ( any thickness but not less than 0.10 (zero point ten) Metre thickness) including attached pilasters buttresses, plinth and string courses etcetra from top of foundation up to floor all levels as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing Tor steel reinforcement of TATA/TISCO/SAIL for RCC work including bending, binding and placing in position complete up to all floor levels with cost of binding wire including carriage of material within all leads, lifts and other incidental and as per the direction of the Engineer-In-Charge .The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Squared rubble masonry coursed with hard stones of approved quality in foundation and plinth including raking out joints in cement mortar 1:6 (one cement is to six sand) as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Squared rubble masonry coursed with hard stones of approved quality in foundation and plinth including raking out joints in cement mortar 1:5 (one cement is to five sand) as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying Damp Proof Course with 38mm (thirty eight millimeters) thick cement concrete 1:2:4((one cement: two sand: four graded crushed stone aggregate 12.5mm (Twelve decimal five millimeters nominal size) and curing complete, as required at site as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Applying a coat of hot bitumen (mexphalt 80/100 (Eighty/Hundred)/VG-10 using 1.70 Kgs. (one decimal seven zero Kilogram) per square metre On Damp Proof Course after cleaning the surface with a piece of cloth lightly soaked in kerosene oil complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying precast cement concrete hollow block masonry with cement concrete blocks of size 40cm x 19cm x20 cm (forty centimeter into nineteen centimeter into twenty centimeter) including quion block, jamb blocks and closers etcetra made of cement concrete 1:3:6 (1 cement : 3 sand : 6 graded stone aggregate 20mm nominal size) laid with cement mortar 1:6 (1 cement : 6 sand) including curing complete in super structure upto floor all level as per specifications, approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing to existing door frames 30mm thick factory made wire mesh solid PVC door shutters consisting of frame made out of (Mild Steel) tube of 19 gauge thickness of size 19mmx19mm for style and 15mmx15mm (Mild Steel) square tube for top, bottom & Lock rail (Mild Steel) frame shall have a coat of steel primer and covered with 5mm thick PVC solid sheet heat moulded "C" channel of size 75mmx30mmx60mm out of which 10mm shall be bent at 90degree towards inner side on front face of the door (Mild Steel) frame at lock rail shall be covered with 100mm wide PVC sheet out of which 10mm on both the edges shall be bent at 90 degree on front face of the door and 85mm wide PVC sheet shall cover the (Mild Steel) frame at top, bottom & lock rail of 70mm on back side of door 5mm thick 20mm wide cross PVC sheet as gap insert for top and bottom rail, PVC sheet beading of 10mm thick, 15mm wide PVC sheet beading is to be stick internally in the back side of style and rails of door with solvent cement adhesive including fixing of G.I. wire mesh 85G or 0.56 mm (Zero point fifty six millimeters) dia wire fixed between PVC sheet of style and rail bent at 90 degree on front face using 15mmx15mm L-shape PVC beading nailed on style a rails including fixing shutter to existing door frame with M.S. butt hinges 100x58x1.90mm with necessary screws etcetra complete as per specification, approved drawing , design or as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying precast cement concrete hollow block masonry with cement concrete blocks of size 40cm x 19cm x20 cm i/c quion block jamb blocks and closers etcetra made of cement concrete 1:3:6 (1 cement : 3 sand : 6 graded stone aggregate 20mm nominal size) laid with cement mortar 1:6 (1 cement : 6 sand) including curing complete in super structure upto floor all level as per specifications approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 12mm thick (twelve milimetre) thick pre-laminated board both side phenol bonded of Alpro/Century ISI marked IS No 12823 (Twelve thousand eight hundred twenty three) exterior/ interior grade both sides of greenlam of approved shade Panelled shutters with 40mm (forty millimeter) frame of first class deadar wood for doors including bright finished/ black enamelled iron butt hinghes with necessary screws etcetera complete as per specification, approved drawing , design or as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 19mm (Nineteen millimeter) thick commercial board water proof board of Uniply / Green ply/century ply IS marked for cup board and shutters shelves. Back side of cup board shall have 6/8 mm thick water proof ply. All the exposed portion of board shall have 6 mm thick hard wood edgenig. The shutter from outer side shall be finished with 1mm thick lamination of Century / Green ply/ Action TirraI of approved shade including hinges, handle,knob megnatic catcher complete as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying mechanically mixed cement concrete 1:5:10 (One cement : Five Sand :Ten graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth as per specifications, approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing magnetic catcher in cup board shutters with necessary screws etcetera complete as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 65x35mm (Sixty five into Thirty five millimeter) special quality bright finished brass cup-board locks or ward robe lock, with six levers including necessary screws etcetera complete (Indian make of approved quality) as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing steel wire gauge shutters (Z-section) using galvanized MS wire gauge of IS gauge designation 85G with wire of dia 0.56 mm (Zero decimal five six millimeter) for doors, windows and clear story windows including bright finished black enameled iron hings with necessary screws as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing M.S.( Mild Steel) plain grills of required pattern in window frames etcetera with M.S.Flats,20x5mm ( twenty into five millimeter) and 8 x 8 mm ( eight into eight millimeter) solid square or round bars, fixing to frames with round headed bolts and nuts or by screws or welding as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25 mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC screws etcetra where ever necessary completd in all respect as per specification, approved drawing , design or as per the entire satisfaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing anodized aluminum sliding door bolt anodized transparent or dyed to required colour and shade with bolts nuts and screws etcetera complete 300 X 16 mm (three hundred into sixteen millimeter) size as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing aluminium tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetera complete as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

200 X 10 mm (two hundred into ten millimeter) size

150 X 10 mm (one hundred fifty into ten millimeter) size

Providing and fixing aluminum handles anodized transparent or dyed to required colour and shade with necessary screws etcetera complete as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

125 mm (one hundred twenty five millimeter) size

100 mm (one hundred millimeter) size

75 mm (seventy five millimeter) size

Providing and fixing aluminium anodized transparent or dyed to required shade and colour hooks and eyes with necessary screws etcetera complete 250 mm (two hundred fifty millimeter) size as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

White glazed tile having size (30x30 cm) (thirty into thirty centimeter) laid on a bed of 12 mm thick cement mortar 1:3(1 cement :3 sand) finished with flush pointing in white cement slurry of orient/bell/kajaria/Rak/Johnson of approved shade as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing automatic hydraulic compressed and polished Precast terrazzo tiles of ISI marked No.1237 of size 300 x 300x 25mm thick vibro compacted of NTC in 70% white & 30% grey cement with chips 55% white 15% each Marron, Yellow and dark green of size 0,B,2B laid in floors, treads of steps, ramp and landings laid on a bed of 25mm thickness of cement mortar 1:6(1 cement : 6 Sand) jointed with cement slurry mixed with pigment to match the shade of tiles (Wherever required) including rubbing , polishing Complete and of approved shade as per specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying ceremic tiles non slippery of Kajaria/Nitco/Orient/Bell in flooring (300*300) mm (Thirty into thirty millimeter) size laid on a bed of 12mm thick cement mortar 1:3 finished with flush pointing in white cement slurry mixed with pigment to match shade of tile including rubbing/nousing/moulding and polishing complete as per specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government..

Providing and fixing Precast terrazzo tiles hydraulic compressed and polished in skirting and risers of steps not exceeding 30 cm in height on 10 mm thick cement plaster 1:3(1 cement: 3 sand)jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required)including rubbing polishing, nosing moulding and cutting complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying 20 mm (twenty milimetre).thick Granite stone slab in work top of kitchen laid over in 12mm (twenty milimetre) thick base in cement mortar 1:3(1cement:3sand) including jointing with cement mortar 1:2 (1 white cement:2 marble dust)with an admixure of pigment to match the shade of the granite stone slab complete as per specifications, approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying 60mm thick inter locking paver blocks of NTC vibro compacted upto M-50 grade including border or Kerb block laid over sub base of 25 mm cement mortar 1:4 (1 cement : 4 sand) and jointed with neat cement slurry to match the shade of block including cuttining and rubbing complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 150mm (One hundred fifty millimeter)size single acting hydraulic floor spring hinges of approved brand ISI Marked with necessary screw etcetra complete including entire carriage of material within all lead, lifts and other incidentals as per approved drawing, design and as directed by the Engineer- in-charge. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing prepainted steel sheet roofing of Tata/ Dura shine/Reliance/ Jindal over steel trusses of 0.60 mm thickness (ISI marked Z-120) over steel truss prepainted galvanized steel and hot diffed metallic zinc coat sheet with top coat of regular modified polystar (RMP) organic coating of 20 micron over 5 (FWE) micron and back coating of polystar 5 (fwe) micron over 5 (fwe) micron primer coating including fixing with prepainted iron jrw hooks, bolts , nuts 6 mm (six millimeter) dia with prepained limpat and rubber washers complete with all accessories as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing ridges or hips 60 cm (Sixty centimeter) over all with 0.60mm (Zero decimal Six zero millimeter) thick pre-painted Steel sheet of Durashine/ Reliance/ Jindal Tata ( Factory made) shall having proper Gola / shape with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with pre-painted iron J or L hooks, bolts and nuts 6mm (Six millimeter) diameter with pre-painted G.I. limpet and bitumen washers complete with all accessories as required as per specifications approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing valley 90cm (Ninety centimeter) over all with 0.60mm (Zero decimal Six zero millimeter) thick pre-painted steel sheet of Tata Durashine in valleys with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (twenty) microns over 5 (Five) microns primer coating to back coat of polyester of 5 (Five) micrors over 5 (Five) microns primer coating including fixing with pre-painted iron J or L hooks, bolts and nuts 6mm (Six millimeter) diametre with pre-painted G.I. limpet and bitumen washers complete as per specifications approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 30cm. (Thirty centimeter) wide 30cm.(Thirty centimeter) deep plain G.I. Sheet of Tata 0.63mm (Zero decimal sixty three) millimeter thick gutter with bolts nuts and washers etcetra including dome shape grating and making necessary connections with rain water pipe complete as per specifications, approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing flashing 38cm. overall with prepainted sheet 0.60 mm (zero decimal six zero millimeter ) thick fixed with prepainted galvanised iron. J or L hooks, bolts and nuts, G.I. limpet washer and bitumen washers complete bent to shape and fixed in walls with cement mortar 1:3 (1 cement : 3 sand) complete as per H.P.P.W.D specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing M.S. ( Mild Steel) B.P. sheet 2.00 mm (two millimeter) thick in eaves boards/facia/soffits /ceiling including cutting, fixing, jointing with gas/electric welding to steel roof members and applying a coat of red lead primer complete (Base members of steel work shall be measured and laid for separately) as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 150mm (oneHundred fifty milimetre) diameter on wall face P.V.C. (D-plast) rain water pipes 2.2mm ( Two decimal Two millimeter) thick of supreme/Finolex/Prince working pressure not less than 4.50 kgs /cm2 (Four decimal five zero kilogram) per square centimeter including filling the joints with approved adhesive complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing on wall face P.V.C. (D-plast) acessories of Supreme/Finolex/Prince/Astral for rain water pipes including filling the joints with approved adhesive complete as per H.P.P.W.D specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

150mm (One hundred fifty millimtre) diametere PVC Plain bend

150mm (One hundred fifty millimtre) diametere PVC shoe

Providing and fixing 150mm (one hundred fifty millimeter) diametre M. S. holder bat clamps of approved design to PVC pipes embedded in cement concrete block 10cmx10cmx10cm (Ten centimeter into Ten centimeter into Ten centimeter) of 1:2:4 (One cement is to Two Sand is to Four graded crushed stone aggregate 20mm (Twenty millimeter) nominal size including cost of cutting holes and making good the wall etcetera as per specifications, approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Steel work of TATA/TISCO/SAIL welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint in beams, joist, channels, angle, tee, flat with connecting plates or angle, cleats as in main and beams, hip and jack rafter fixing in rafter, purlin connects to common rafter in trusses complete as per H.P.P.W.D specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing angle iron door frame (Single rebate) manufactured from M.S. angle iron section of 35x35x4mm(thirty five into thirty five into four milimetre) and M.S flat 50x4mm ( Fifty into four milimetre) as per drawing and design including hinges jamb, lock jamb, beed and if required angle threshold of mild steel angle 50x25 mm (Fifty into twenty five milimetre) welded or rigidly fixed by mechanical means, lugs with split end tails to each jamb including steel but hinges 2.5 mm (Two decimal five milimetre) thick with provision for locking arrangement and shock observer as specified and applying a coat of approved steel primer after pretreatment of the surface as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals . The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing angle iron door frame (Double rebate) manufactured from M.S. angle iron section of 40x40x4mm(forty into forty into four milimetre) and M.S flat 50x4mm ( Fifty into four milimetre) as per drawing and design including hinges jamb, lock jamb, beed and if required angle threshold of mild steel angle 50x25 mm (Fifty into twenty five milimetre) welded or rigidly fixed by mechanical means, lugs with split end tails to each jamb including steel but hinges 2.5 mm (Two decimal five milimetre) thick with provision for locking arrangement and shock observer as specified and applying a coat of approved steel primer after pretreatment of the surface as directed by the Engineer-in-Charge including carriage of materials within all leads and lifts and other incidentals . The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing M.S. channels frames 75x40x4mm (Seventy five into Forty into four millimeter) door/ windows/ ventilator frame and M.S. flat 75x4mm (Seventy five into Four millimeter) combination welded together to make a one frame as per design, drawing including hinges, jambs, beads if required, threshold of M.S. angles 50x25 (fifty into twenty five millimeter) welders rigidity fixed by mechanical means, hinges with split end tails to each jambs with a provision of locking arrangements, shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of surfaces as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections joints mitred and welded with 16 x3.15 mm (Sixteen into three decimal one five millimeter) iron lugs 10 cm (Ten centimeter) long embedded in cement - concrete blocks 15cm x 10cm x 10 cm (fifteen into ten into ten centimeters) size of 1:3:6 (one cement : three sand: 6 stone aggregate ) 20mm (twenty millimeter) nominal size or with wooden plugs and screws rawl plugs and screws or with fixing clips or bolts and nuts as required and iron fitting including providing and fixing of glass panes with glazing clips and special metal sash putty of approved make complete including applying a priming coat of red lead paints as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

side hung

Fixed

Providing and laying double coat water proofing treatment done with Dr. Fixit pidifroof over toilet area polymer modified cementitious coating consisting of cementitious powder and a polymer liquid. Water proof coating shall be done in two coats as follows. After laying the drain pipes the floor concrete / slab shall be admixed with Dr. fixit pidi proof LW@200ml/50 ks bag of cement if crack are found there at the junction or in between the slab then before applying Dr. Fixit Pidi proof LW, the junction of the wall/ Beams and slab shall be rounded using cement mortar of 1:5 admixed with Dr. Fixit Pidi Proof LM integral water proofing compound confirming to IS-2645 as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing railing 85cm high for staircase having baluster 19x19mm and 12x12mm M.S. solid square bar with clear height of 85cm at the rate of 60 cm centre to centre and to be embeded in cement concrete step and jointed with electric gas welding at top along with MS hollow pipe hand rail of size 75x65mm of 14 to 16 (fourteen to sixteen ) gauge vertical blassters, welded/ jointed with each other with 2 Nos. M.S.flat of 40x6 mm (fourty into six millimeter) complete with applying a coat of red lead paint complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing of 50 mm dia (fifty millimeter) M.S. hollow pipe hand rail slip resistance with round ended at two level at 75 cm to 90 cm in height. It shall be 30cm (thirty centimeter) beyond the top and bottom 25mm dia M.S. baluster to be welded with M.S. hollow pipe and emended in cement concrete 600 mm c/c (six hundred millimeter centre to centre) with applying a coat of red lead paint as per approved drawing , design or as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint of Asian/ Nerolac brushing to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters with enamel paint of approval shade as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil,grease,dirt and other foreign matters sand papering and knotting as required with ready mixed paint of Asian / Nerolac brushing wood pink primer as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Painting two coats(excluding priming coat) on new wood and wood based surface with ready mixed enamel paint of Asian / Nerolac brushing to give an even shade including cleaning the surface of dirt, dust and other foreign matters sand papering and Knotting with enamel paint other than white complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

6mm (Six millimeter) thick cement plasters in ceiling with cement mortar 1:3 (One cement: Three sand) for all heights as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

15 mm (Fifteen millimeter) thick cement plaster in single coat on rough side of brick/concretes/ stone walls for interior plastering up to all floor levels including arises, internal angles, chamfers and rounded angles not exceeding 80mm (Eighty millimeter) in girth and finished even and smooth with cement mortar 1:6 (One cement is to six sand) as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

15 mm (Fifteen millimeter) thick cement plaster in single coat on fair side of brick/concretes/ stone walls for interior plastering up to all floor levels including arises, internal angles, chamfers and rounded angles not exceeding 80mm (Eighty millimeter) in girth and finished even and smooth with cement mortar 1:6 (1 cement : 6 sand) as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

15 mm (Fifteen millimeter) thick cement plaster in single coat on fair side of brick/concretes/ stone walls for exterior plastering up to all floor levels including arises, internal angles, chamfers and rounded angles not exceeding 80mm (Eighty millimeter) in girth and finished even and smooth with cement mortar 1:5 (1 cement : 5 sand) as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

15 mm (Fifteen millimeter) thick cement plaster in single coat on rough side of brick/concretes/ stone walls for interior plastering up to all floor levels including arises, internal angles, chamfers and rounded angles not exceeding 80mm (Eighty millimeter) in girth and finished even and smooth with cement mortar 1:3 (One cement is to Three sand) as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar dropping, dust, loose material and other foreign matters, sand papered smooth to give final matt finish to the surface complete. as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Distempering (two coats) with acrylic/ synthetic /washable distemper of Asian/Nerolac of approved shade manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Finishing wall with water proofing cement paint of approved brand (Apex ultima of asian paint, Nerolac paint) of required shade on un-decorated wall surfaces(two coats) to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer- in-charge. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 6 mm (Six millimeter) thick cement bounded partical board ceiling of panel fixed to including cost of M.S. flat/cleat 40x5 mm (Forty into five millimeter) framing @ 600 mm (Six hundred millimeter) centere to centre complete, as per specifications, approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

White washing with lime (Two or more coats) on undecorated wall surfaces, ceiling or sloping surfaces to give an even shade including thoroughly brooming the surface to remove all dirt, dust, mortar droppings and other foreign matter as per H.P.P.W.D specification, approved drawing , design or as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, Sale Tax, Toll tax, GST and all type of taxes imposed by the Government.

Providing under layer for plinth protection of 75mm (seventy five millimeter) thick bed of dry brick / stone aggregate 40mm (forty millimeter) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing plinth protection 50mm (fifty millimeter) thick in cement concrete 1:3:6 (one cement is to three sand is to six graded stone aggregate 20mm(twenty millimeter) nominal size) as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Construction of cement concrete covered drain size 15x23 cm in cement concrete 1:3:6 (one cement : three sand : six graded stone aggregate 20mm (twenty millimeter) nominal size including shuttering and earth work and cast in situ reinforced cement concrete slab over drain and cement concrete flooring 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (twenty millimeter) nominal size and finished with a floating coat of neat cement complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and filling on brick bats/ stone aggregate in soak pit as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Half brick masonry using second class common brunt clay building bricks in super structure above plinth level to floor all levels in cement mortar 1:4 (one cement is to four sand) as per specifications approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying in trenches galvanized mild steel tubes (medium grade) tube fittings (Earth work in trenches to be measured and paid for separately) 20 mm (twenty millimeter) nominal bore as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 1.00 HP (One Horse power) Tulu pump (water lifting pump) of Kirloskar/ Cromption including board and fittings complete as per specifications, approved drawing , design and entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 600 x 450 mm (Six Hundred into four hundred fifty millimeters) light duty C.I. Manhole cover with frame. The weight of cover with frame shall be 38 Kg (Thirty eight Kilogram). Weight of cover 23 kg (Twenty three kilogram) and weight of frame 15 kg (Fifteen kilogram) (single seal) as per H.P.P.W.D specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing polythene aluminum polythene (P.E.) A.E P.E composite pressure pipe U.V. stabilized with carbon block confirming to I.S. 15450-2004 Flow guard/ Kitec for water supply including clamps at one metre spacing, cutting, fixing and making good the walls etcetera; but excluding the cost of fittings (Internal work) pipes exposed on wall including filling the joints with approved adhesive complete and entire carriage of material with in all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

1216 (16 mm O.D.) pipe

1620 (20 mm O.D.) pipe

Providing and fixingPE-AL-PE-Composite end seal compression fittings of Kitec as per IS:15450-2004 for cold water supply tees,elbows,reducers,connectors,couplers and clamps with jointing testing and fitting complete including cutting and making good the wall etcetera and entire carriage of material with in all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Equal tees (1216)

Equal tees (1620)

Equal Elbow (1216)

Equal Elbow (1620)

Female branch Tee (1216x1216x15 mm thread)

Female branch Tee (1620x1620x20 mm thread)

Female Elbow (1216x15 mm thread)

Female Elbow (1620x15 mm thread)

Male thread Connector 1216x15 mm thread

Male thread Connector 1620x15 mm thread

Female thread Connector 1216x15 mm thread

Female thread Connector 1620x15 mm thread

Reducer 1620 x1216

Coupler 1216

Coupler 1620

Making connection of glavanised mild steel distribution branch with galvanised mild steel main 20mm to 40mm nominal bore by providing and fixing tee including cutting and threading the pipe complete and entire carriage of material with in all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing in trenches P.V.C. pipe of Supreme/ Finolex /Prince class “A” soil waste and ventilating pipe fixing with approved adhesive mixure complete 4.6mm (four point six millimeter) thick shall be conform to IS No. 13592-92, It should be fire resistance, chemical resistance and should be able with stand temp upto 60⁰ c all junction fitting shall conform to IS No. 14735-99 and shall be jointed to each other by a rubber ring/ push fit jointing system with a sealing ring and a rubber lubricant adhesive for PVC pipe / ventilation pipe type A within all leads, lifts and other incidentals as per approved specifications drawing, design and as directed by the Engineer- in-charge.The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

110mm nominal bore/diameter.

75mm nominal bore/diameter

Providing and fixing PVC clamps for PVC pipes fitting with steel screws and rawls plugs etctera complete. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

110mm nominal bore/diameters.

75mm nominal bore/diameters

Providing and fixing P.V.C accessories Supreme/ prince/ Finolex for Sewerage pipe conforming to IS No. 14735-99 P.V.C. Plain bend includingcarriage of material with in all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

110mm nominal bore/diameter.

75mm nominal bore/diameter

Providing and fixing P.V.C of Supreme/ prince/Finolex tees medium including fixing with approved adhesive etcetra complete The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

110mm nominal bore/diameters.

75mm nominal bore/diameters

Providing and fixing PVC heal rest Supreme/ prince/ Finolex including fitting the joints with approved adhesive mixure complete The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government. .

110mm nominal bore/diameters.

75mm nominal bore/diameters

Providing and fixing P.V.C. coller of Supreme/prince/ Finolex including fixing with approved adhesive etcetra.complete The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

110mm nominal bore/diameter

75mm nominal bore/diameter

Providing and fixing P.V.C. cowl of Supreme/ prince/ Finolex including fixing with approved adhesive etcetra complete The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

110mm nominal bore/diameter

75mm nominal bore/diameter

Providing and fixing 100mm (One hundred millimeter) nominal size/diameter P.V.C. floor trap of Supreme/ prince/ Finolex ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floor etcetra complete including within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing European sheet No 20041 of Cera / Hindware / ESSESS/Jaguar vitreous china water closet (European type with integral P or S trap including jointing the trap with soil pipe in cement motar of approved adhesive (sheet cover and jet spray to be measured and paid for separately) as per approved specification and entire satisfaction of Engineer in charge. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixingP.V.C.10.00 litres PVC china low level flushing cistern of cera/Hindware/ESSESS/Jauuar with a pair of C.I or mild steel brackets, complete with fittings such as lead valve less syphon 15mm nominal size bras, ball valve with polythene float, C,P brass handle, unions and couplings for connections with inlet, outlet and over flow pipes 40mm dia C.P flush band including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet as per approved specification and entire satisfaction of Engineer in charge. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing in position with clamp 32mm nominal internal diameter PVC flushof supreme/ESSESS/ Jindal / for low level flushing cistern includings connecting the flush pipe with cistern and cleset and making good the walls and floors. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing plastic seat (solid type) and cover of Cera / Hindware / ESSESS/Jaguer of approved shade for wash down water closet with C.P. Brass hinges and rubber buffers with cover. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing ISI mark No 10008 of Cera / Hindware / ESSESS/Jaguar or equivalent flat back 550x400 (Five hundred fifty into four hundred millimeter) vitreous china wash basin white shade with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittingsas as per specification approved drawing , design, as per the entire satisifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana and all type of taxes imposed by the Government.

Providing and fixing stainless steel kitchen sink having size 161.4 x54 Cm of AMC / UNIK/ Diamond of ISI make with drain board and C.P. waste with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fitting The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing vitreous china pedestal of Cera / Hindware/jaguar for wash basin complete recessed at the back for the receiption of pipe and fittings. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 32mm nominal size diameter rubber plug for wash basin (Heavy duty ). The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 32mm diameters M.I. union for wash basin or sink Jal/Jaguar/ESSESS including necessary fittings. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 32mm diameters P.V.C. waste pipe Supreme/finolex/prince waste pipe for wash basin or sink including brass check nut The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 100mm diametres C.P. Grating of Jal/Jaguar /ESS-ESS (Heavy duty makes ISI marked ) for gully / floor or Nahni trap including fitting in all respect The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing flat back 600x450mm beveled edge mirror or superior glass of Atul/Modi Gaurd mounted on 6mm thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washers etcetra complete. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing C.P.(chromium plated) brass towel rail having size 600x20 mm of Jal/Jaguar ESSESS complete withC.P. brass brackets fixed to wooden plugs with C.P. brass screws etcetra complete. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 600x120mm glass shelf (Heavy duty makes ISI marked IS No. 8931 & 8934) with C.P. brass brackets and guard rail complete fixed to wooden plugs with C.P. brass screws etcetra complete. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing C.P. Brass Toilet paper holder of Jal/Jaguar / Kingston/Pasko/Sieko (Heavy duty make ISI including fitting complete in all respect) The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing chromium plated jet pressure of Jal/Jaguar / ESSESS .The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 15mm diameter chromium plate PTMT push cock tap of Jal/Jaguar / ESS ESS with necessary fittings including entire carriage of material with in all leads and lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 15mm nominal bore fancy bib tap chromium plated ISI marked IS No. 8934 of Jal/Jaguar /ESSESS with necessary fittings including entire carriage of material with in all leads and lifts .The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 15mm diameter C.P.(Chromium plated) brass stop cock of Jal/Jaguar / ESSESS with fitting complete. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 15mm dia C.P. brass pillar tap with capstan head of Jal/Jaguar / ESS ESS with fitting complete in all respect .The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 15mm diameter brass angle valve of Jal/Jaguar/ESSESS with nuts as per approved specifications drawing ,design and as directed by the Engineer-Incharge

Providing and fixing brass full way valve with wheel of Jal/Jaguar/ESSESS with necessary fitting including entire carriage of material with in all leads and lifts and other incidentals.The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

15mm nominal bore

20mm nominal bore

Providing and fixing 15mm nominal bore brass valve (Horizontal plunger) type of Jal/Jaguar/ESSESS high pressure with copper plate with necessary fitting including entire carriage of material with in all leads , lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 15mm nominal bore PVC connection pipe with brass union 45cm length, with necessary fittings. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing PVC water Storage tank (Sintex) tripple layer 1000 litres net capacity ISI marked with G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto any height above ground level including carriage of material with in all leads , lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying to level or slopes PVC pipe for sewerage line of diametre 150 mm overall pipe 8 mm thick of supreme/Finolex/Prince and jointing with approved adhesive complete .The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete 1:5:10(One cement: five sand: ten graded crushed stone aggregate 40mm (Forty millimeters) nominal; size for bedding for 150 mm (one hundred fifty millimeter) diameter P.V.C. pipe including necessary form work and curing complete, as per specifications, approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Construction manhole with R.C.C. top slab in 1:2:4(1 cement: 2 sand: 4 graded crushed stone aggregate 20mm nominal size) foundation concrete 1:4:8(1 cement: 4 sand: 8 graded crushed/broken stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1 Cement: 3 sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(1 cement: 2 sand: 4 graded crushed stone aggregate 20mm nominal size) finished smooth complete including curing and testing inside size 800x800x500mm deep, including C.I. cover with frame (light duty single seal pattern -I) 455x610mm internal dimensions.Ttotal weight of cover and frame to be not less than 38 Kg Weight of cover 23Kg and weight of frame 15 Kgs with 300mm thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (1 cement: 3 sand). The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Construction manhole with R.C.C. top slab in 1:2:4(1 cement: 2 sand: 4 graded crushed stone aggregate 20mm foundation concrete 1:4:8(1 cement: 4 sand:8 graded crushed/broken stone aggregate 40mm inside plastering 15mm thick with cement mortar 1:3 (1 Cement: 3 sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(1 cement: 2 sand: 4 graded crushed stone aggregate 20mm nominal size) finished smooth complete including curing and testing inside size 800x800mm 1.00 mtr deep, including C.I. cover with frame (light duty single seal pattern -I) 455x610mm internal dimension. Total weight of cover and frame to be not less than 38 Kg Weight of cover 23Kg and weight of frame 15 Kg with 300mm thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (1cement: 3 sand) .The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Excavation in drains and channels etcetra in earth work in all kind of soil, such as pick work, jumper work, pick jumper work, blasting work, hard and soft blasting, saturator soil including chiseling or any other mixed variety of soil, lift upto any heights, stacking the excavated soil for all heights from the edge of excavation and then returning the stacked soil in 15cm layer when required into plinths sides of foundations etc. Consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated earth as directed by the Engineer- Incharge .The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

M/s Surindera Traders

vikas parmar