E.T.No.-EDC(USN)63/2025-26

Annexure-A (LABOUR CHARGES)

Earthing of distribution transformer including digging of pit of size 2.5 Mtr depth and make hole of size 150 mm. Placing of earthing electrode, connecting the same with G.I. Strip of size 35x6 mm for a minimum lenght 6 m. treatment of soil with highly condctive substance as per IS 30343 complete in all respect, result of earthing resistance to be recroded in M.B. before and after installation of earthing. The earth resistance after earthing should be less than 1 Ohm.

Earthing of support with M.S. Earth rod of 2.5 meter long by hammaring of M.S. Rod to proper depth and connecting the earth electrode with the help of G.I. wire as per construction manual.

Fabrication of MS Channel angle iron etc in required sizes with drilling of holes upto good finish for top channel, bracing and special type bracket etc. as per RESPO schedule and local approved drawing.

Excavation of earth for stay pit of size 0.6x0.6x1.2 mtr in all types of soil including proper dressing of sides and ramming of bottom including getting out the excavated soil and disposal of surplus excavated soil as directed complete work

Fixing, tightening and nozzling of stay with pole and stay rod on required tension as per drawing/manual in 11 KV line

Grouting of Stay in size 0.6x0.6x0.3 in CC ratio 1:4:8 (1 cement : 4 graded stone 20mm nominal size : 8 coarse sand ) block including cost of Cement, sand and stone ballast back filling of soil and boulders in pit and ramming and proper alignment, leveling as per RESSPO Manual.

Excavation of earth for pole pit of size 0.9x0.6x1/6 of full length of pole for erection of pole in all types of soil including proper dressing of sides and ramming of bottom including etting out the excavated soil and disposal of surplus excavated soil as directed complete work.

Erection of SP-55 single support pole in proper level and alignment along with fixing of all accessories like top channel & clamps as per RESPO manual

Erection of Sp-55 double support pole in proper level and alignment along with fixing of all accessories like top channel, X bracings & clamps as per RESPO manual.

Grouting of pole in size 0.45x0.45x1/9 of the support in CC ratio 1:4:8 (1 cement:4 graded stone20 mm niminal size: 8 coarse sand) block including cost of cement, sand and stone ballast back filling of soil and boulders in pit and ramming and proper alignment, levelling as per RESPO cnstruction manual

Muffing of poles size 0.45x0.60 cm radius with 1:3:6 (1 cement:3 coarse sand :graded stone 10 mm nominal size) block size 45 cm height from ground level including cost of cement,stone and sand etc

Dismantling of existing LT/HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store (PCC Single Pole).

Dismantling of existing LT/HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(SP-55 Single Pole).

Dismantling of existing LT/HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(SP-55 Double Pole)

Dismantling of existing HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(ACSR Rabbit).

Dismantling of existing LT line 1P2W, including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(ACSR Weasel)

Dismantling of Transformers from double pole /plinth including opening of all connections, circuts & earthing strip etc. (25 KVA).

Dismantling of Transformers from double pole /plinth including opening of all connections, circuts & earthing strip etc. (63 KVA).

Dismantling of Transformers from double pole /plinth including opening of all connections, circuts & earthing strip etc. (100 KVA).

Dismantling of Transformers from double pole/plinth including opening of all connections, circuts & earthing strip etc. (250 KVA).

Dismantling of Transformers from double pole/plinth including opening of all connections, circuts & earthing strip etc. (400 KVA).

Excavation of earth of size 2.1x2.1x1.2 meter for DTR Plinth.

Cement concreting work in ratio 1:4:8 for DTR Plinth.

Brick work in 1:4 ratio for DTR Plinth.

RR massonary work in 1:6 ratio for DTR Plinth.

RCC Work of 1:2:4 ratio 15 cm thickness for DTR Plinth.

Cement Plaster on side walls in 1:4 ratio on DTR Plinth.

Erection, providing and fixing of wire mesh of size 50x35 mm around plinth and toe wall duly welded with frame of M.S angle iron 35 x35x6 mm and strip of size 35x6 mm in mid of each side along with wire mesh (width of wire mesh 1.5 meter ) with the height of 0.5 meter above the plinth and 2 meter above the toe wall with 1 No. gate and locking arrangment in the toe wall size including grouting of 6 Nos. legs in the ratio in block of size 0.25x0.25x0.45 meter including gravlling of shingle of size 20 to 40 mm and complete painting of wire mesh with aluminium paint with two coat (Including the cost of cement and all material).

Installation/mounting of new 100KVA Tranformer on pole structure and fixing of channel /angle etc. and making all connections of HT and LT side and its complete commissioning.

Installation/mounting of new 63 KVA Tranformer on pole structure and fixing of channel /angle etc. and making all connections of HT and LT side and its complete commissioning.

Installation/mounting of new 25 KVA Tranformer on pole structure and fixing of channel /angle etc. and making all connections of HT and LT side and its complete commissioning.

Installation/mounting of new 400 KVA/500 KVA Tranformer on plinth structure and fixing of channel / angle etc. and making all conn ections of Ht and LT side and its complete commissioning.

Installation/mounting of new 250 KVA Tranformer on plinth structure and fixing of channel / angle etc. and making all connections of Ht and LT side and its complete commissioning.

Mounting & Fixing of TPMO on double pole structures including making of connections complete work.

Mounting & Fixing of Fuse sets on double pole structures including making of connections complete work.

Mounting and Fixing of Lightning arrestor set (3 Nos.) on double pole structure including making all connections by G.I. strip size 35x6 mm to earth point complete work (excluding cost of G.I.Strip).

Laying, Spreading, Stringing and sagging of 11 KV /33 KV line in 3 phase (3 Phase 3 wire) of ACSR Rabbit as phase wire with G.I. earth wire complete including fixing of all accessories in 3 Nos. conductor in parallel with binding and jumpering as per profile and profile and sagging chart.

Laying, Spreading, Stringing and sagging of 11 KV / 33 KV line in 3 phase (3 Phase 3 wire) of ACSR Dog as phase wire with G.I. earth wire complete including fixing of all accessories in 3 Nos. conductor in parallel with binding and jumpering as per profile and profile and sagging chart.

Cartage of ST pole SP-55 Poles from store centre to construction site with loading, unloading at both points and proper stacking.(Distance 0-20 Km)

Cartage of other material (other than poles) by vehicle from Store Center to nearest construction site Store including loading and unloading at both ends(distance 0-20 Km)

Headload cartage of ST Pole SP-55 from road to site (distance 0-1 Km)

Head load cartage of small material (distance 0-1 Km)

Dismantling of Fencing and Gate of S/S including fabrication cutting and welding works at 33/11 KV Sub Station.

Dismantling of Aerial Bunch Cable of all Sizes.

Laying Sagging of LT XLPE AB CABLE 3X120+1X95+1X16 Sq.mm

Back Cartage of Petty material, 0-20 Km.

Fixing of IPC with AL. Bail for Earthing.

Installation of ACB LT Distribution Box.

Opening of 11 KV Jumper and Making again of section pole

Fixing of MS channel, angle and all accessories on existing/new double pole.

Fixing of 11 KV 90KN Tension Clamp B&IPC

Fixing of 11 KV Suspension Ties.

Fixing of 11 KV IPC for CC to CC Conductor.

Fixing of 11 KV IPC for CC to Bare Conductor.

Fixing of 11 KV Mid Span Jointing Kit.

Back head load cartage of small line material 0-1 Km

Fixing of 11 KV pin insulator.

Supply & fixing suspension clamp with eye hook.

Supply & fixing Dead End Clamp.

Dismantling of 11KV AAAC conductor.

Laying Spreading, Stringing AAAC Conductor.

Fixing of PP Clamp.

Straightening & laying of GI strip earthing for structure /panel.

Earthing with copper plate, Charcoal, salt digging with duly provided 1 No cast copper plate.

Dismantling of plinth 500 to 630KVA & cable Hardware.

Annexure-B (SUPPLY ITEMS) (As per UPCL Specifications)

Supply of Top Channel Clmap for SP-55

Supply of Stay Clamp D/E with N&B

Supply of Holding Clamp for SP-55 with N/B

Supply of F-Clamp

Supply of Suspension Clamp with Eye Hook for LT AB Cable.

Supply of Dead End Clamp for AB Cable.

Supply of LT Clamps for Distribution Box.

Supply of 11 KV Fuse Set.

Supply of SMC Three Phase L.T. Distribution Box with inbuilt panal lock, Al bus bar RYB 25x6mm., Al Busbar N. 40x6mm. for connection of L.T. consumer (Sintex make or other ISI mark reputed company) with Panel Lock with key).

Supply of PRC 120-120

Supply of IPC with Al. BAIL for Earthing 11 KV

Supply of 11 KV IPC for Covered to Covered Conductor.

Supply of 11 KV IPC for Covered to Bare Conductor.

Supply of 11 KV mid span Jointing Kit

Supply of 11 KV Sus. Ties/Cable Ties for Pin Insulator

Supply of Complete set of 11 KV, 400Amp AB Switch.

Supply of 11 KV AAAC Covered Conductor AL-59, 99 Sq.mm.

Supply of G.I. Strip 50x6 mm.

Supply of 11 KV Tension Clamp with BAIL & IPC

Please Enable Macros to View BoQ information