SETTING UP OF ACCOMMODATION FOR THREE SQUADRONS AS A

Amount

Total amount of Sch 'A' part-I ( Buildings/Structures)

Total amount of Sch 'A' part-II (Excavation, earthwork & Site Develoment)

Total amount of Sch 'A' part-III (Demolition of existing structures)

Total amount of Sch 'A' part-IV (Internal Water Supply)

Total amount of Sch 'A' part-V (Internal Electric Supply)

Total amount of Sch 'A' part-VI (External Water Supply)

Total amount of Sch 'A' part-VII ( External Electric Supply)

Total amount of Sch 'A' part-VIII ( Area Drainage)

Total amount of Sch 'A' part-IX (Sewage Disposal)

Total amount of Sch 'A' part-X (Road, Path and Culvert)

Total amount of Sch 'A' part-XI (Retaining wall/Parapet wall)

Total amount of Sch 'A' part- XII (Fire Fighting Works)

Total amount of Sch 'A' part- XIII (Covered links (Regular connected corridor and Stepped connection corridor))

SCH. 'A' PART -XIII (MISCELLANEOUS) Note :- This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Internal Water Supply:- Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 20 mm bore and fixed ( Code No. OPP-15001 of Jaquar or equivalent of other make specified in the list of manufacturer ) complete all as specified .

Bib Cock, chromium plated, cast copper alloy long body screwed for CPVC pipe 15/16 mm dia bore.Make: Jaquar Code No CON- 107 KN or equivalent of other make specified in the list of manufacturer complete all as specified

Angular stop cock, chromium plated, cast copper alloy, screwed down, screwed for CPVC pipe 20mm dia bore Make Jaquar code No CON-059KN or equivalent of other make specified in the list of manufacturer complete all as specified

Concealed stop cock, long body chromium plated, cast copper alloy, screwed down,screwed for iron pipe 15/16mm dia bore for shower rose Make Jaquar code No CON 087FTK+ALD-087FT or equivalent of other make specified in the list of manufacturers complete all as specified

Chromium plated brass over head water shower of 120mm diameter. (Jaquar Catalog No. OHS-1799 & SHA-483 or equivalent specified in the list of manufacturer complete all as specified

Health Faucet Make jaquar Cat Part No. ALD-579 or equivalent of other make specified in the list of manufacturer with 1.0 Mtr flexible tube 16mm dia (outer), low density polythene, suitable for cold water application complete with union and teflone washers and holder to suit 15mm angle cocks complete all as specified

Low density ploythene pipe 16 mm dia (outer), metallic baided, 450 mm long suitable for cold/Hot water application complete with brass union on both sides complete all as specified

INTERNAL ELECTRIFICATION :- Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor 1.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. with and including heavy duty non metalic regid PVC concealed conduit medium duty and conduit accessories concealed in wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), with galvanised modular mild steel/pressed steel sunken boxes (with earth dolly) duly electroplated, covered with modular frame and base plate for fixing of modular switches, sockets and fan regulators etc, including one run of PVC insulated multi-stranded copper conductor 1.5 Sqmm nominal cross sectional area single core F.R.L.S. cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the following:- (NOTE: (i) Switches, sockets, regulators to be measured and paid for separately.

(a) All as per item No. 22 here-in-before but for One light point controlled by one 5/6 amps one way switch complete all as specified

(b) All as per item No. 22 here-in-before but for One ceiling fan/exhaust point controlled by one 5/6 amps one way switch and one fan regulator complete all as specified

(c) All as per item No. 22 here-in-before but for One Socket outlet, three pin, 5 Amp, independent controlled by one 5/6 amps one way switch or switch/socket combination 5 amps, 5 pin complete all as specified

(d) All as per item No. 22 here-in-before but for One Socket outlet, three pin, 5 Amp, controlled by by one 5/6 amps one way switch or switch/socket combination 5 amps, 3 pin. on the same board with other switches, sockets, fan regulators etccomplete all as specified

(e) All as per item No. 22 here-in-before but for one light point conrolled by 2 Nos, 2 way switches 5/6 Amps complete all as specified

Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor 2.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. with and including heavy duty non metalic regid PVC concealed conduit medium duty and conduit accessories concealed in wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), with galvanised modular mild steel/pressed steel sunken boxes (with earth dolly) duly electroplated, covered with modular frame and base plate for fixing of modular switches and sockets etc, including on run of PVC insulated multi-stranded copper conductor 2.5 Sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the one 15/16 amps socket outlet independent board:- (NOTE: Switch and socket to be measured and paid for separately)

Supply, fixing, testing and commissioning of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one double pole 20A MCB all as specified

Supply, fixing, testing and commisioning of RCBO double pole (DP) 16 A, 100mA,AC,230V,10KA,ISI marked as per IS 12640-2,IP 20 protected terminal front phase indication for earth leakage fault colour coded ON/OFF indication on dolly .Make:legrand Cat No.411331 or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commisioning of RCBO double pole (DP) 25 A, 100mA,AC,230V,10KA,ISI marked as per IS 12640-2,IP 20 protected terminal front phase indication for earth leakage fault colour coded ON/OFF indication on dolly .Make:legrand Cat No.411332 or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commisioning of RCBO double pole (DP) 40 A, 100mA,AC,230V,10KA,ISI marked as per IS 12640-2,IP 20 protected terminal front phase indication for earth leakage fault colour coded ON/OFF indication on dolly .Make:legrand Cat No.411334 or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commisioning of RCBO four pole (4P) 25A, 100mA, AC,415V,10KA, ISI marked as per IS 12640-2, IP 20 protected terminal front phase indication for earth leakage fault colour coded ON/OFF indication on dolly. Make:legrand Cat No.411371 or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commisioning of RCBO four pole (4P) 40A, 100mA, AC,415V,10KA, ISI marked as per IS 12640-2, IP 20 protected terminal front phase indication for earth leakage fault colour coded ON/OFF indication on dolly. Make:legrand Cat No.411373 or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commisioning of MCCB three pole (3P) 25A, AC,415V,16KA, ISI marked Make:legrand, Cat No 420001 or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commisioning of MCCB three pole (3P) 40A, AC,415V,16KA, ISI marked Make:legrand, Cat No 420002 or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commisioning of MCCB three pole (3P) 63A, AC,415V,16KA, ISI marked Make:legrand, Cat No 420003 or equivalent in other makes as specified in the list of manufacturers complete all as specified

Earthing complete with galvanised steel earth plate electrode size 600x600x6.0mm thick burried directly in ground vertically in a pit of depth not less than 2.25 mtr below normal ground level with top edge of the earth plate not less than 1.5 mtr below normal ground level surrounded from all sides by mixture of charcoal and common salt and electrode connected to and including galvanised earth lead 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and earth wire protected by GI protection pipe light grade 15mm dia connected to main earth wire on pole or control board and GI pipe medium grade 20mm bore for watering, funnel with wire mesh. PCC chamber pit in PCC 1:3:6 type C-1, 40 mm thick precast RCC M-25 (design mix) cover reinforced with 8 mm dia TMT bars @ 10 cm C/C on both sides and handle, excavation and earth work in any type of soil and removal upto 50 m complete all as specified and shown in electric plate No.03 of SSR Part-I(2009), connecting to earthing test point all as specified including testing on completion.

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified

Submain wiring with 2 run of 2.5Sqmm two single core (for phase and neutral) using multistranded copper conductor PVC (FRLS) insulated unsheathed with and incl 2.5Sqmm insulated unsheathed PVC insulated multistranded copper conductor as earth continuity conductor connected to common earth dolly drawn in PVC concealed conduit not less than 20mm dia ISI marked with accessories complete all as specified (Note: 03 runs of 2.5Sqmm and one run of PVC concealed conduit shall be measured as one run only)

Submain wiring with 2 run of 4Sqmm two single core (for phase and neutral) using multistranded copper conductor PVC (FRLS) insulated unsheathed with and incl 4Sqmm insulated unsheathed PVC insulated multistranded copper conductor as earth continuity conductor connected to common earth dolly drawn in PVC concealed conduit not less than 20mm dia ISI marked with accessories complete all as specified (Note: 03 runs of 4Sqmm and one run of PVC concealed conduit shall be measured as one run only)

Submain wiring with 2 run of 6Sqmm two single core (for phase and neutral) using multistranded copper conductor PVC (FRLS) insulated unsheathed with and incl 6Sqmm insulated unsheathed PVC insulated multistranded copper conductor as earth continuity conductor connected to common earth dolly drawn in PVC concealed conduit not less than 25mm dia ISI marked with accessories complete all as specified (Note: 03 runs of 6Sqmm and one run of PVC concealed conduit shall be measured as one run only)

Submain wiring with 4 run of 6Sqmm four single core (for phase and neutral) using multistranded copper conductor PVC (FRLS) insulated unsheathed with and including 2 runs of 6Sqmm insulated unsheathed PVC insulated multistranded copper conductor as earth continuity conductor connected to common earth dolly drawn in PVC concealed conduit not less than 32mm dia ISI marked with accessories complete all as specified and directed. (Note: 06 runs of 6Sqmm and one run of PVC concealed conduit shall be measured as one run only)

Supply, fixing, testing and commissioning of decorative Ultra slim linear 20 W, 4 feet LED lighting fixture with extruded Aluminium heat sink, environmental friendly, energy efficient prewired with lamp, AC, 230V, ISI marked. Make : Philips model No. BN021C LED 20S or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commissioning of decorative Ultra slim linear 9/10 W, 2 feet LED lighting fixture with extruded Aluminium heat sink, environmental friendly, energy efficient prewired with lamp, AC, 230V, ISI marked. Make : Philips model No. BN021C LED 10S-6500 or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commissioning of 1 x 15W LED fitting including lamp, 230v, Indoor recess / surface mounting downlight circular type with reflector, connector block etc., complete with all accessories pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size. Philips model No. SM251C LED 16S-6500 PSU WH or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commissioning of foot lamp - 5 watt LED - 4 module, AC, 230V, ISI marked. including all connections and accessories as required. Make : Havells cat. no. AHLPFCWL04 or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commissioning of square type surface mounted light fitting 12W LED, with extruded Aluminium heat sink, environmental friendly, energy efficient prewired with lamp, AC, 230V, ISI marked, complete all as specified Make : philips model No.: SM 200C LED11 S 6500 PSU OD WH or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commissioning of decorative type table lamp light fitting 5W LED, with environmental friendly, energy efficient prewired with lamp, AC, 230V, IS marked, complete all as specified. Make : Luker LED table lamp LTL05 or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commissioning of LED light fitting including lamp, 1 x 25W, Wallmounted type with multi color ABS housing with polycarbonate rings, and glass shade with lamp holder, connector block, etc., complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230v,50Hz, complete all as specified. Make : Luker LED wall mounted lamp LWL10E27 or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commissioning of LED light fitting including lamp, 1 x 3W, Cupboard /wall mounted type 230v, epoxy powder coated CRCA sheet housing with reflector cover channel, with drive unit, connector block, etc., complete with all accessories internally pre wired and including connection up with twin core twisted flexible copper conductor cable with suitable size, complete all as specified. Make : Philips strike shape cabinet lamp or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commissioning of 3W LED Bed light fittings inculing all conections and accessaries as required, complete all as specified. Make : Luker LED focus light LSP 04 or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commissioning of smart xtra 40 W, 4 feet LED aluminium batten lighting fixture suitable for surace/ wall & conduit mounting with extruded Aluminium heat sink, environmental friendly, energy efficient prewired with lamp, AC, 230V, ISI marked. Make : Philips model No. BN100C LED 40S-6500 PSU L120 GR or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commissioning of 40/41W, LED downlighter fixture suitable for surace/ recess mounting (double height ceiling) with extruded Aluminium heat sink, environmental friendly, energy efficient prewired with lamp, AC, 230V, ISI marked. Make : Wipro model No. LED Gimball LD56-501-060-40-XX** or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commissioning of 30W, LED wall mounted light fixture with extruded Aluminium heat sink, environmental friendly, energy efficient prewired with lamp, AC, 230V, ISI marked. Including wall mounting bracket fabricated out of 40mm dia. GI bracket light grade bend to shape of 1.5mtr and two nos. wall mounting clamps using 25x4mm thick MS strip bend to shape and welded with pipe to form solid structure and one run of 1.0sq.mm PVC insulated multistrand copper conductor wire connecting PVC terminal to fitting complete, complete all as specified. Make : Wipro model No. Skyline LED LR02-331-XXX-57- XX or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, fixing, testing and commissioning of MCB SP 06 to 32 A, AC, 230V, 10KA complete all as specified

Supply, fixing, testing and commissioning of MCB SP 40 A, AC, 230V, 10KA complete all as specified

Supply, fixing, testing and commissioning of MCB 63A, TPN, AC, 433V, 10KA complete all as specified

Supply, fixing, testing and commissioning of MCB 40A, TPN, AC, 433V, 10KA complete all as specified

Supply, fixing, testing and commissioning of MCB 25A, TPN, AC, 433V, 10KA complete all as specified

Supply, Installation, testing and commissioning of surface/recess mounting, vertical type, 415 volts, prewired, TPN MCB distribution board of sheet steel, dust protected, duly phosphatized and powder painted, inclusive of 250 Amps tinned copper busbar for each phase, common neutral link, earth bar, din bar for mounting MCB's detachable gland/ knock out plate, and with built in loose wire box and superior make terminal connectors for all incoming and outgoing circuits, duly prewired with adequate size of FR PVC insulated copper conductor upto the terminal connector/ neutral link and ready for installation of following ways (but without MCB's and incomer) as required. - 4Way VTPN DB with metal door, complete all as specified Legrand Catalogue no.: 507756 or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, Installation ,testing and commissioning of surface/recess mounting, vertical type, 415 volts, prewired, TPN MCB distribution board of sheet steel, dust protected, duly phosphatized and powder painted, inclusive of 250 Amps tinned copper busbar for each phase, common neutral link, earth bar, din bar for mounting MCB's detachable gland/ knock out plate, and with built in loose wire box and superior make terminal connectors for all incoming and outgoing circuits, duly prewired with adequate size of FR PVC insulated copper conductor upto the terminal connector/ neutral link and ready for installation of following ways (but without MCB's and incomer) as required. - 8Way VTPN DB with metal door, complete all as specified Legrand Catalogue no.: 5077 59 or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, Installation ,testing and commissioning of surface/recess mounting, vertical type, 415 volts, prewired, TPN MCB distribution board of sheet steel, dust protected, duly phosphatized and powder painted, inclusive of 250 Amps tinned copper busbar for each phase, common neutral link, earth bar, din bar for mounting MCB's detachable gland/ knock out plate, and with built in loose wire box and superior make terminal connectors for all incoming and outgoing circuits, duly prewired with adequate size of FR PVC insulated copper conductor upto the terminal connector/ neutral link and ready for installation of following ways (but without MCB's and incomer) as required. - 12Way VTPN DB with metal door, complete all as specified Legrand Catalogue no.: 5077 60 or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, installation, testing and commissioning of ceiling fan,copper wound,1200mm sweep, service value not less than 4.5 as per IS374-2019, including fixing of down rod of any length suitable from ceiling,canopy,mounting clamp etc.AC, 230V, and connecting up complete with and including three core flexible PVC insulated multi stranded copper conductor cable of size 1.50 Sq mm from ceiling rose/ connector to fan. Note:-Rate quoted shall deemed to be included for suitable length of down rod from roof to false ceiling as directed by engineer in charge, complete all as specified.

Supply, installation, testing and commissioning of exhaust fan, electric single phase AC 230 Volts, Copper wound, self opening louvers complete 300mm Sweep ,1380 RPM air delivery not less than 1600 cu.mtr/min connect to ceiling rose all as directed, complete all as specified. Make : Crompton Greaves model Transair or equivalent in other makes as specified in the list of manufacturers complete all as specified

Supply, installation, testing and commissioning of exhaust fan, electric single phase AC 230 Volts, Copper wound, self opening louvers complete 250mm Sweep ,1250 RPM air delivery not less than 720 cu.mtr/min connect to ceiling rose all as directed, complete all as specified. Make : Crompton Greaves model Brisk Air 10" or equivalent in other makes as specified in the list of manufacturers complete all as specified

Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Panel fabricated out of 2mm thick for indoor panel CRCA sheet steel in cubical compartmentallised, free standing floor mounted on a base frame, totally enclosed, extensible type dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. The general construction shall confirm to IS:8623/93. Cable gland plates shall be provided on top as well as bottom of the panels with minimum 3mm thick plate. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3- Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels. Approval of GAD along with BOM shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanize and Zinc passivated). Ingress protection shall be IP54 minimum for indoor use and IP 66 for out door purpose. Complete board shall be factory fabricated and ready for installtion at site. After the fabrication and before the despatching, the panel should be tested for high voltage test at 2.5 kV, insulation resistance test by 1000V megger, polarity test, Power and control circuit's continuity test , operational test before the Engineer-In charge/nominated person complete all as specified :-

MDB-1 (Squadron 1 a) - Indoor type, INCOMER - 1 no. 250 Amps TPN MCCB ,36 kA MCCB having thermal magnetic releases for S/C, O/C, releases, IDMTL Protection for S/C, O/C releases with front drive kit. METERING & INDICATION - 1 set of phase LED indicating lamps, 1 Set of Breaker ON-OFF-TRIP indication Lamps, BUS BAR:- 1 Set of 400 Amps, TPN Aluminum bus bars with colour coded sleeves. OUTGOINGS - 6 Nos. - 80 Amps, TPN MCCB 16KA, 1no. - 63A TPN MCCB,16KA, 1no. - 40 Amps TPN MCCB, 16KA with Thermal O/L and Magnetic S/C Protection and suitable extension of breaker terminals, with front drive kit complete all as specified

MDB-2 (Squadron 1 a) - Indoor type, INCOMER - 1 no. 250 Amps TPN MCCB ,36 kA MCCB having thermal magnetic releases for S/C, O/C, releases, IDMTL Protection for S/C, O/C releases with front drive kit. METERING & INDICATION - 1 set of phase LED indicating lamps, 1 Set of Breaker ON-OFF-TRIP indication Lamps, BUS BAR:- 1 Set of 400 Amps, TPN Aluminum bus bars with colour coded sleeves. OUTGOINGS - 7 Nos. - 80 Amps, TPN MCCB 16KA, 1no. - 40 Amps TPN MCCB, 16KA with Thermal O/L and Magnetic S/C Protection and suitable extension of breaker terminals, with front drive kit complete all as specified

MDB-1 , MDB-2 (Squadron 1 b - Block 1 & 2) - Indoor type, INCOMER - 1 no. 200 Amps TPN MCCB ,36 kA MCCB having thermal magnetic releases for S/C, O/C, releases, IDMTL Protection for S/C, O/C releases with front drive kit. METERING & INDICATION 1 set of phase LED indicating lamps, 1 Set of Breaker ON-OFF-TRIP indication Lamps, BUS BAR:- 1 Set of 400 Amps, TPN Aluminum bus bars with colour coded sleeves. OUTGOINGS - 6 Nos. - 63 Amps, TPN MCCB 16KA with Thermal O/L and Magnetic S/C Protection and suitable extension of breaker terminals, with front drive kit complete all as specified

Supply and fixing of modular TV socket 1 module including modular plate, metal flush box, complete all as specified. Make : Legrand Cat. Part No. 675546/ 676360/ 689007 or equivalent make complete all as specified

EXTERNAL WATER SUPPLY :- Cutting and jointing Existing CI pipe 150mm dia by inserting of DI Tee 150*150*150 including jointing materials, DI specials, necessary excavation, returning filling and making good the surface complete all as specified

EXTERNAL ELECTRIC SUPPLY : Supply, laying and testing cable XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty)/ 11000 volts grade (E) with stranded aluminium conductor of size 3 core 185 Sqmm complete all as specified

Supply, Installation, testing and commissioning of 11 KV Compact Sub Station (CSS) with and including non extensible RMU consisting of 1 No, manually operated 11 KV/630 Amps VCB in SF6 insulated stainless enclosure, HT Cable/Bus bar, 1 No transformer 1000 KVA, 11 KV/433 & associated LT Distribution system, & suitable capacity Battery bank, battery charger complete all as described & specified below :-

HT SWITCHGEAR - 11 kV 630Amps 21 kA for 3 sec. SF6 insulated Extensible Compact switchgear (Type CV) consisting of One No. Fixed Manual Load Break Switch and One No Fixed Manual Vacuum Circuit Breakers in SF6 insulated Stainless steel enclosure of 2.5 mm thickness having IP 67, with series trip,self powered microprocessor based numerical over current and Earth Fault (IDMT+Inst.) relay protection. Interconnection between HT switchgear and transformer shall be using 1Cx3x95 sq.mm Aluminium unarmorured XLPE Cable. - 1 No, Relay shall be with communication port.- 1 No, Protection CT: 40/1 Amps,2.5VA,5P10 - 3 nos, Manometer - 01 No, Operating Handle - 01 No.

TRANSFORMER - 1000 KVA, 11 KV/433V DYn11 Oil filled fully hermatically sealed, copper wound, transformer with corrugated wall design & Top Bushings for LT with Off load tap switch of rating +5% to -1 0% in steps of 2.5%. Temp rise over amb temp 50 Deg C: 40/45 for Oil/Winding respectively. Insulation Class A; (Losses as per IS 1180 Energy Efficiency Level 2) Max Losses @ 50% Loading: 2790W and Max Losses @ 100% Loading:7700W. % Z- 5% ( IS Tol). - 01 Nos, Oil Temperature Indicator with Alarm and Trip Contact - 01 No, Winding Temperature Indicator with Alarm and Trip Contact - 01 No

LVS PANEL- 2500 AMPS ALUMINUM BUSBAR (100% FOR PHASE AND 50% FOR Outgoing panel - 2000 AMPS ALUMINUM BUSBAR (100% FOR PHASE AND 50% FOR NEUTRAL, CURRENT DENSITY- 1 AMP/SQMM) - Incomer from Transformer - 2000 AMPS, 433V, 4P 50 KA Manually Fixed type Air Circuit Breaker (ACB) with microprocessor Based over current, short circuit and earth fault Release - 01 No, LED Type Indicating Lamps- R,Y,B Phase and ON-OFF-TRIP- 01 Set, Digital Multifunction meter of class 1.0 accuracy with RS485 Port- 01 No. OUTGOING - 630 AMPS 433V 4P 36KA Manually Fixed type Molded Case Circuit Breaker (MCCB) with micro processor based over current & short circuit fault Release. - 06 Nos., 200 AMPS 433V 4P 25KA Manually Fixed type Molded Case Circuit Breaker (MCCB) with Thermal Magnetic Based over current & short circuit fault Release. - 02 Nos., 100 AMPS 433V 4P 25KA Manually Fixed type Molded Case Circuit Breaker (MCCB) with Thermal Magnetic Based over current & short circuit fault Release. - 01 No.

OUTDOOR ENCLOSURE - Outdoor type enclosure with slant roof having construction of Galvanised Sheet Steel of thickness 2 mm for Load bearing member and 1.5 m for Non Load bearing member. The Enclosure shall have IP54 degree of protection for HT & LT switchgear compartment & IP23 degree of protection for Transformer compartment. The enclosure exterior shall be Polyuratne painted (Colour Light Gray & D.A.Gray ). Each compartment will be provided with the door and pad locking arrangement. The Compartment illumination lamp with door operated switch shall be provided for each compartment. Seperate switch operated bulket lamp + Hooter shall be provided in Transformer compartment. - 01 Set

INTERCONNECTION AND EARTHING - Interconnection Between HT switchgear & Transformer using 1Cx3x95 Sq.mm Aluminium unarmorured XLPE Cable. & Interconnection between Transformer & LT switchgear using Aluminium Busbars. Internal earthing connections by using 50 x 6 GI strips including Transformer Neutral earthing.- 01 job

Supply, Installation, testing and commissioning of outdoor type factory made, CPRI type tested Automatic Power Factor Control (APFC) cubical panel of suitable size for 275 KVAR (3x50KVAR, 3X25KVAR, 1X15KVAR, 2X10KVAR, 3X5KVAR) dust and vermin proof, made out of 3mm thick CRCA steel sheet confirming to relevant IS, double door type floor mounted in MS angle iron support of suitable size grouted on floor, for 415Volts, 3 phase, 50HZ AC supply, including 3nos. of suitable ratio current transformer with necessary entries for incoming/ outgoing multi strand cables of suitable size with glands, lugs, etc., for each feeder, front open hinged door for each compartment of controls and duly painted with powder coated paint both internally & externally, provision of suitable ration CT one no. in the incoming of main panel for ensuring the PF and making connections with & including following fittings/ instruments - Make : Schneider Electric/ Legrand or equivalent.

(a) Bus bar chamber TPN aluminium busbars for 3 phase and 500Amps for Neutral duly insulated sleeves with different colour codes. (b) MCCB 630Amps TPN, 440V, 50HZ AC supply, 25KA. (c) 50KVAR Heavy duty box energy (MD-XL) Capacitor 440V, 3 phase - 03 Nos. with following (i) MCCB 125Amps TP, 25KA, with fixed magnetic setting 415V, 50Hz - 03 Nos. (ii) Contactor TP 100amps, 240Volts coil voltage - 03 Nos. (d) 25KVAR Heavy duty box energy (MD-XL) Capacitor 440V, 3 phase - 03 Nos. with following (i) MCCB 63Amps TP, 10KA, with fixed magnetic setting 415V, 50Hz - 03 Nos. (ii) Contactor TP 45amps, 240Volts coil voltage - 03 Nos. (e) 15KVAR Heavy duty box energy (MD-XL) Capacitor 440V, 3 phase - 01 No. with following (i) MCB 63Amps TP, 10KA, with fixed magnetic setting 415V, 50Hz - 01 No. (ii) Contactor TP 45amps, 240Volts coil voltage - 01No. (f) 10KVAR Heavy duty box energy (MD-XL) Capacitor 440V, 3 phase - 02 Nos. with following (i) MCB 40Amps TP, 10KA, with fixed magnetic setting 415V, 50Hz - 02 Nos. (ii) Contactor TP 32amps, 240Volts coil voltage - 02 Nos. (g) 5KVAR Heavy duty box energy (MD-XL) Capacitor 440V, 3 phase - 03 Nos. with following (i) MCB 25Amps TP, 10KA, with fixed magnetic setting 415V, 50Hz - 03 Nos. (ii) Contactor TP 25amps, 240Volts coil voltage.

Supply, installation, testing and commissioning of HT 11 KV, 3 phase, 50 cycles totally enclosed metal clad switchgear complete with Vacuum circuit breaker having rupturing capacity upto 350 MVA, overload and earth fault protection, ammeter, voltmeter and of rating upto 630 Amps including 11 KV single phase in door resin cast CT of ratio 400/5- 5A class 1.0/ 5P10,burden 15VA – 15 VA all as per existing Make & model to match the existing HT panel in SS No 9. Note : The cost is inclusive for necessary Modification of Existing HT panel for accomadating new VCB by extending HT panel including bus bar and accessories.

Supply, installation, testing and commissioning of 12 KV SF6 out door Ring main unit (RMU) comprise of Two Nos 630 Amps Load Break Switch and 1 Nos 630 Amps Vaccum "T" OFF circuit breaker with self powered (3 O/C & 01 E/F) relays with RS-485 port for communication on MODBUS. RMU shall be one side extentable & inbuilt battery bank & battery charger of suitable capacity. (A) Load Break Switch 630 Amps - Load Break Switch shall be Mannualy operated, Earthing switch with making capacity, Live cable LED indicators throuh capacitor voltabe divider mounted on the bushing, Machanical ON / OFF earthing indication, suitable cable entry box for up to 3x300 Sq mm. (B) Vaccum Circuit Breaker 630 Amps - VCB shall be Motorised operated & earth switching with making capacity, Auxilary contacts, Live cable LED indicators through capacitor voltage divider mounted on the bushing, Mechanical ON / OFF earthing indication, self powered (3 O/C & 01 E/F) Relays should have facility to trip the breaker from remote command without requiring shunt trip coil, suitable cable entry box for up to 3x300 Sq mm complete all as specified

Supply and fix cable jointing kit for 11 KV (Earthed) grade cable for indoor termination complete with jointing material heat shrinkable type and accessories suitable for 3 core XLPE armoured Aluminium conductor cable of size 185 sq mm complete all as specified

Supply and fix cable jointing kit for 11 KV (Earthed) grade cable for straight through heat shrinkable type joint complete with jointing material and accessories suitable for 3 core XLPE, armoured, AIuminium conductor cable of size 185sq.mm Outdoor type complete all as specified

M & L for earthing complete with galvanised steel earth plate electrode of size 600mm x600mmx6.0 mm thick burried directly under ground vertically to a depth not less than 2.25 meter below ground level with top edge of the plate at a depth not less than 1.5 m below ground level connected to and including galvanised strip 32 x 6mm, by means of bolts, nuts, check nuts and washeres made out of GI including protection pipe GI light grade 40 mm size and watering pipe 20 mm dia GI medium grade all as shown on plate No 3 of SSR Part-I, connecting to earthing test point, including necessary earth work in any type of soil, PCC earth chamber made in PCC 1:3:6 type C1 (using 20mm graded aggregate), common salt, charcoal, CI funnel, earth pit cover in RCC 1 :2:4 type B1 (using 20mm graded aggregates), with 8mm CTD bars @ 140mm c/c in both ways, including necessary form work complete including necessry test on completion all as specified and as directed.

Supply, laying and testing cable XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 4 core 10 sqmm.(street lights) complete all as specified

All as per item No 92 here-in-before but for cable size 4 core 25 Sq mm

All as per item No 92 here-in-before but for cable size 3.5 core 35 Sq mm

All as per item No 92 here-in-before but for cable size 3.5 core 150 Sq mm

All as per item No 92 here-in-before but for cable size 3.5 core 185 Sq mm

Supply, installation, testing and commissioning of LT panel board CPRI approved with with CRCA Sheet steel 3mm thick outdoor type cubical type compartmentalised, having busbar capacity 800 Amps, ammeter with CT's, voltmeter, indicating lamps with and following breakers as incoming and Outgoings Incoming : 4 pole MCCB 630 Amps, 415V, 50Hz with breaking capacity 50KA, O/C and E/F protection - 01 no. Outgoing : 4 pole MCCB 250 Amps, 415V, 50Hzwith breaking capacity 35KA, O/C and E/F protection - 02 nos. (01 Spare), 4 pole MCCB 200 Amps, 415V, 50Hz with breaking capacity 35KA, O/C and E/F protection - 02 nos (01 Spare), complete all as specified.

Supply and fixing of steel tubular swaged poles Type 410SP-22 (8.5 meter long) Swan Neck Type complete with CI base plate and finial tapper plug, bolts, nuts and washers and single swan neck, including 3 coat of bitumen paint internally complete and externally for the portion embedded in concrete and two coats of aluminium paint over a coat of red oxide primer to the balance portion of external surface and all as specified and directed. Note : Excavation and PCC shall be measured and paid seperately under relevant item of schedule 'A' foundation and coping.

Supply, installation, testing and commissioning of LED street light fitting 35/36W die cast aluminium housing 3600 lumen light output, Voltage Rating-220-240V, Input Frequency-50-60Hz, 5KV surge protection, power factor 0.95 THD less than 10%, IP66 protection and heat resisitant toughened glass with frame including all accessories and suitable bracket including connecting from terminal box to fitting with 3 core 1.5sq.mm flexible copper wire in PVC flexible conduit, etc., and tesing on completion all as specified and directed. Make: Philips - Green line BRP409 LED CW 036 MR FG S1 PSU GR or equivalent of CGL/Wipro.

Supply and fixing of solar all in one LED street lighting - smart integrated solar street light with build in Poly Crystalline Panel, lithium ferro phospate (LiFePO 4) battery, MPPT charge controller and PIR sensor and 6mtr height pole. Philips catalogue No. BRP710 LED45 CW MR S1 12V LFP Solar IN or equivalent in other makes as specified in the list of manufacturers complete all as specified

Riddled soil as earth cushioning to UG cable by using IS sieve to separate the composite particle/roots etc and refilling/spread in trenches as cushioning and rammed down to form a solid bed all as specified and as directe. Note:- 1. Punned thickness shall be measured and paid seperately. 2. Excavated approved soil shall be riddled by using sieve to separate composite particles etc as per IS.

Supply and fixing terminal box, pole mounted made out of polycarbonate IP66 with MCB SP 6Amps and connection of size 130x130x77mm for street light fitting complete all as specified and as directed. Make : Hensel, Cat No KF0600B or equivalent in other makes as specified in the list of manufacturers.

DG Panel (Emergency lighting) : Supply, installation, testing and commissioning of LT panel board (Outdoor type) IP65 made of modular polycarbonate thermoplastic enclosures shall be environment friendly recyclable, UV resistant, halogen and silicon free, anti acid and anti corrosive. The gasket materials shall be polyurethane and shall be internally embedded, having busbar capacity 100 Amps, ammeter with CT's, voltmeter, indicating lamps with and following breakers as incoming and Outgoings. Incoming : 4 pole MCCB 63 Amps, 415V, 50Hz with breaking capacity 25KA, O/C and E/F protection - 01 No, Outgoing : 4 Pole MCCB 32 Amps, 50 Hz, 415 V with rupturing capacity 16 KA - 5 Nos., 4 Pole MCCB 25 Amps, 50 Hz, 415 V with rupturing capacity 16 KA - 4 Nos.

Street light feeder pillar - Outdoor type - Supply, installation, testing and commissioning of street light feeder pillar IP65 made of modular polycarbonate thermoplastic enclosures shall be environment friendly recyclable, UV resistant, halogen and silicon free, anti acid and anti corrosive. The gasket materials shall be polyurethane and shall be internally embedded. with incomer 25amps TPN MCCB with dual sensor (LDR and astronomical timer, Legrand cat. no. AlphaRex3 D21 astro or equivalent) to regulate 'ON' 'OFF' with contactor required MCB and IP66 protection incoming switch shall have front drive kit) with 4nos 10amps DP MCB 10kA for outgoing complete all as specified

Supply, laying, testing and commissioning of cable XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoued, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 2core 6sq.mm (Street lights) complete all as specified.

M&L for cable route indicator 15cm dia circular type made out of cast iron duly embedded with size and type of HT cable and arrow mark indicating direction fixed on ISA 40x40x6mm angle iron support including PCC 1:2:4,type B1 (300x300x400mm) and steel surface painted with two coats of anti corrossive paint over a coat of red oxide primer including necessary earthwork complete all as specified and directed

M&L for cable route indicator 15cm dia circular type made out of cast iron duly embedded with size and type of LT cable and arrow mark indicating direction fixed on ISA 40x40x6mm angle iron support including PCC 1:2:4,type B1 (300x300x400mm) and steel surface painted with two coats of anti corrossive paint over a coat of red oxide primer including necessary earthwork complete all as specified and directed

Miscellaneous: Rigid non-metalic PVC conduit exclusive of boxes (junction / terminal but inlcusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc of dia 25 mm complete all as specified

SEWAGE DISPOSAL : Supply and laying of DWC PE Pipe (SN8) 180 (OD)/163 (ID) mm dia laid and jointed including all fittings and fixtures complete all as specified

Supply and laying of DWC PE Pipe (SN8) 200 (OD)/183 (ID) mm dia laid and jointed including all fittings and fixtures complete all as specified

Supply and laying of DWC PE Pipe (SN8) 300 (OD)/283 (ID) mm dia laid and jointed including all fittings and fixtures complete all as specified

RETAINING WALL : Supplying and laying 100mm dia PVC pipe (LDPE) of rating 6kg/cm2 for Weep holes complete all as specified.

Proding and Fixing of UPVC Pipes (SCH-40) for Rain Water downtake with all fitting and fixtures. like shoe,bends cowl etc. complete all as specified

LIGHTNING PROTECTION : - Supplying, intallation, testing and commissioning of the advanced lightning protection "Collection Volume Method Type" Air terminal for coverage for 100mtr dia mounted at the height of 5mtr from the terrace with all accessories required for its proper functioning. (a) Supply, install multistranded single core copper conductor of size 50Sqmm of length approx 50RM terminated at the earthing test point (b) Supplying, installation, testing and commissioning of the lighting strike recorder for lightning strikes captued by the air terminal. The recorder sensitive range of 1500amps to a maximum of 220 KA @ 8/20µs. (c) Supplying, installation, testing and commissioning of efficient earthing system with copper binded earth rod, clamp, copper tape, ground resistance improvement powder (GRIP) all as required including excavation of earth etc as required as per manufacturer recommendation of 2 nos. with earth value 1 ohm. Make : Erico, model-nVent Erico system 3000 or equivalent Note : The rate includes necessary civil works, supports and all other materials required as per the recommendation of the manufacturer and testing on completion

FIRE FIGHTING SYSTEM : Supply and installation commissioning & testing Fire Fighting Terrace pump electrically driven working on 440V, 3 phase, 50Hz, horizontal end suction, centrifugal type confirming to IS 12469-1988 with CI casing, bronze impeller and stainless steel shaft mounted on heavy duty bearings suitable for continuous operation with 'range of operation' 0% to 150% of rated discharge capacity 900 LPM @ 30 meter head (01 as main pump) complete all as specified

Supply and installation commissioning & testing Fire Fighting Motor control panel outdoor type made of polycarbonate suitable for working 01 No terrace pump appx capacity 15 HP on Auto mode complete with MCCB as incomer. Bus bar, Motor starter, multifunction meter etc including internal wiring from automatic pressure switch, wiring rom panel to motor complete all as specified and OEM requirements

M & L MS bracket fabricated out of L angle / flats of required size with 8mm GI 'U' clamps, GI washers, nuts, bolts etc for supporting MS pipe as per the requirement at site complete all as specified

Supply and fix Automatic air release valve 50mm dia suitable for domestic water with 50mm gun metal stop valve complete all as specified

Supply and fix Strainer Y type conforming to IS, size 150 mm (6”) dia complete all as specified

Supply, erecting and commissioning 'C' class ERW MS pipe (ISI marked) as per IS 1239 Part-1, 100mm dia for fire hydrant down comer system. The pipe shall be laid on the floor / fixed on walls or suspended from ceiling / truss or in trenches with necessary specials such as bends, reducer, orifice plate, tee flanges tapers etc including fixing materials such as MS bracket fabricated out of L angle / flats of required size with 8mm GI 'U' clamps with GI washers, nuts etc for supporting MS pipe. The work shall also be include making holes, grouting RCC slabs / masonry walls making good the same. The rates shall include the cost of consumables for cutting and welding, paining with a coat of red oxide two coats of post office red colour for exposed surface of pipes and two coats of bituminous paint on surface of MS pipe laid in trenches all as specified and directed at site. (Note: Necessary MS clamps / U clamps and earth work shall be measured and paid separately) complete all as specified

Supply, erecting and commissioning 'C' class ERW MS pipe (ISI marked) as per IS 1239 Part-1, 150mm dia for fire hydrant down comer system. The pipe shall be laid on the floor / fixed on walls or suspended from ceiling / truss or in trenches with necessary specials such as bends, reducer, orifice plate, tee flanges tapers etc including fixing materials such as MS bracket fabricated out of L angle / flats of required size with 8mm GI 'U' clamps with GI washers, nuts etc for supporting MS pipe. The work shall also be include making holes, grouting RCC slabs / masonry walls making good the same. The rates shall include the cost of consumables for cutting and welding, paining with a coat of red oxide two coats of post office red colour for exposed surface of pipes and two coats of bituminous paint on surface of MS pipe laid in trenches all as specified and directed at site. (Note: Necessary MS clamps / U clamps and earth work shall be measured and paid separately) complete all as specified

Supply, erecting and commissioning 'C' class ERW MS pipe (ISI marked) as per IS 1239 Part-1, 25mm dia for fire hydrant down comer system. The pipe shall be laid on the floor / fixed on walls or suspended from ceiling / truss or in trenches with necessary specials such as bends, reducer, orifice plate, tee flanges tapers etc including fixing materials such as MS bracket fabricated out of L angle / flats of required size with 8mm GI 'U' clamps with GI washers, nuts etc for supporting MS pipe. The work shall also be include making holes, grouting RCC slabs / masonry walls making good the same. The rates shall include the cost of consumables for cutting and welding, paining with a coat of red oxide two coats of post office red colour for exposed surface of pipes and two coats of bituminous paint on surface of MS pipe laid in trenches all as specified and directed at site. (Note: Necessary MS clamps / U clamps and earth work shall be measured and paid separately) complete all as specified

Supply, laying jointing testing and commissioning complete at site as per specification of centrifugally cast (Spun) ductile iron pressure pipes (S & S) ISI marked for water conforming to IS 8329 / 2000 with class K9 of size 150mm dia (6") in trenches road crossing along etc suitable for tyton joint complete including rubber gasket (ISI marked) for jointing materials all as specified. Note: Necessary earth work, DI specials shall be measured and paid separately complete all as specified

M & L for DI fitting of any type suitable for spigot, socket pipe such as bend, tapers, socket, tee, cross, collars, caps, lugs and flanges etc as specified

Supply and fix hose box for keeping 2 Nos hose pipe of length 15mtr each, made out of 18 gauge MS sheet 800mmx600mmx250mm with double door with 4mm thick glass and door frame made out of 16gauge MS sheet complete all as specified

Supply and fix fire hose reel wall mounted swinging type fitted with 20mm dia 30 mtr long high pressure branded rubber hose with gun metal shut off nozzle and 25mm dia inlet wall confirming to IS 884 - 1969 complete all as specified

Supply, laying and testing cable XLPE insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 3.5 core 50 Sq mm complete all as specified

Supply and fix wall mounted LED emergency exit signage luminaire lit up using regular mains supply with a unique rechargeable Ni-cd battery of emergency backup upto 02 hours (Cat No. BESL 03 LED DSD WBB RED make in Bajaj / Havells or equivalent complete all as specified

DG Set: Supply, installation, testing and commissioning of silent Diesel Engine driven generating set 415 volts, 3 phase 4 wire, engine as per IS 10001 /10002 and alternator as per IS 13364 complete with relay panel and switch gears for automatic starting on main failure, control panel having meter with bypass arrangement and consider suitable MCCB and sound proof canopy as per CPCB norm and foundation etc, of capacity 25 KVA as specified below :-

Silent diesel engine driven generating set with AMF PANEL panel 25 KVA with water cooled engine of suitable BHP for 20 KW power generation @ RPM 1500, brushless frame with silencer and Canopy for sound less mode (sound level not exceeding level specified by central pollution control board) and all engine accessories such as self starter, alternator/dynamo and 20 kW/25 kVA electric alternator, 415 volts, 3 phase, 4 wire,50 Hz, Voltage Regulation ± 15, Insulation class H coupled to engine with suitable coupling and base frame on foundation as recommended by the manufacturer and consisting of other electrical components, fuel tank of capacity of not less than 200 ltrs with level indicator installed on suitable steel frame with PCC foundation as per manufacturers instructions, Power Command genset Controller, fuel pipes, Dual spin on fuel filter, Dritype Air cleaner, Shut off coil with safeties for LLOP/HWT , fuel pipes , bar metre, hour meter , oil temperature gauges, ammeter, ignition switch, radiator with cooling fan, maintenance free battery, including suitable size of copper cable leads with terminals, all mountings, accessories and necessary foundation and AVM pads complete as per manufacurers recommendations and to the satisfaction of Engr in charge.

PRIME MOVER :- Suitable for driving 20 KW/25 KVA alternator water cooled battery start diesel Engine of adequate capacity 32 BHP confirming of BSS 649 and fuel tank suitable for 12 hrs running capacity mounted on MS frame pedestal supported with anti-vibration mounting rated for continuous running capable of taking 10% over load for one hr in any 12 hrs operaton complete with the following standard accessories :- a)Fly wheel to match with the flexible coupling b)Flexible coupling wih guard c)Air cleaner oil bath type / dry type d)Lubricating oil filter, fuel filter paper element type e)Blower type fan and radiator f)Governor for class "A" Goverming as per IS-1601 of DS 649/1958 g) Starter. Motor for electric start complete with dynamo altermator , lead acid batteries heavy duty of capacity 12 V 70 Ah or adequate size, Nos & capacity as required with copper conductor leads of adequate size and length not less than 2 M including battery box all as directed. h) Hour meter and RPM indicator i) Exhaust pipe brough outside the building and lagging of entire length of exhaust pipe with 12 mm dia. j) Instrument panel duly wired comprising the following including protection for low lub oils high temperature :- k) Lube oil pressure gauge m) Battery change indicator meter n) Starting switch with key o) Lub oil temperature p) Water temperature

ALTERNATOR : 20 KW/25 KVA at 0.8 PF Brushless self excited, self regulaed 3 phase 50 Hz 415 V 1500 RPM 4 wire screen protected drip proof free from simulation problems continuous rating confirming to BS 2613 complete with automatic voltage regulator O/P voltage regulated between +/- 1 % or set voltage from no load.

Note: i) any fittings/fixtures which are necessary for proper functioning of the DG set shall also be deemed include in the unit rate quoted and shall be provided by the contractor without any extra cost to the Dept. ii) Necessary foundation for installation of DG set shall be provided as per manufaturers recommendations and cost deemed to be inclusive in the rate quoted for this item. iii) All testing equipments are to be arranged by the contractor and testing shall be carried out by the contractor in presence of Engineer-in-Charge and testing result duly signed by the Engineer-in-charge and the contractor shall be kept in Record. iv) Rate quoted by the contractor including the rate of first filling of lubricating oil, Coolent and duct with wooden cover from DG set to AMF Panel. AMF panel must be out side the canopy. (v) Drawings/cataloge for DG Set and AMF panel got approved by the GE before ordering to the manufaturer

COOLING APPLIANCES:- Water cooler fully stainless steel Electric driven (single phase) having approx storage capacity of 80 litres and nominal cooling capacity of 40 litres per hour having minium 5 star rating all as per specification and upto the satisfaction of Engineer in Charge.

Supply and fix voltage stabilizer for automatic operation, single phase naturally air cooled indoor type and designed for input variation between 170V to 250V with output voltage stabilized at 230V with accuracy of +/- 2.5% and of capacity 1 KVA complete all as specified Make: V-Guard (Model - VGSD100) or equivalent manufactures

HOT WATER SUPPLY Supply and fix storage vertical type water heater (Geyser) 25 Ltrs capacity, AC, 230 V, 2000W having 5 star rating as per BEE standard, outer body made out of rust proof ABS materials with PUF insulation, inner tank made out of high quality steel with enamel coating suitable for working pressure. Make: V-Guard / Bajaj / Racold

Marymatha Infrastructure Private Limited

PUSHKARRAJ CONSTRUCTION PRIVATE LIMITED

Rabina Enterprises Pvt Ltd