Repair Replacement of Joinery, Rolling Shutters, Collapsible Gate, Valley Gutters, Plastering, Flooring and Certain Connected Repair Works at New MO V, NSB, NAMAC, WED and Meghadripeta under GE ND, Visakhapatnam

Amount

Taking down Chowkats or frame with shutters [without taking off shutter from the frame] not exceeding 1.5 Sq.m each and removing to store complete all as specified and as directed.

Taking down Chowkats or frame with shutters [without taking off shutter from the frame] exceeding 1.5 Sq.m but not exceeding 4.00 Sq.m each and removing to store complete all as specified and as directed.

Taking down Shutters of any description not exceeding 1.00 Sq.m each complete all as specified and as directed.

Taking down Shutters of any description exceeding 1.00 Sq.m but not exceeding 2.00 Sq.m each complete all as specified and as directed.

Demolition of Unreinforced Cement Concrete in ground floors and Pavings not exceeding 15cm thick [below or above ground level] and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

Demolition of Brick / Stone Masonry built in Cement Mortar including all quoins arches pillars etc and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

M & L for brick work with Fly Ash bricks, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces etc including raking out joints, hacking for key scrubbing down with water etc and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:4, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for Cutting / Chipping the spalling concrete surfaces of Slabs, Beams, Columns, Fins, Facias, Parapets & Chajjas etc. and trimming, cleaning the surfaces of any thickness to receive Guniting / Plastering, preparing surfaces and applying a coat of Zinc rich epoxy primer to all steel surfaces as antirust agent and welding steel wire Fabric / Mesh of size 75X25mm of weight not less then 3.0KG per Sq.m to existing reinforcement, applying a coat of Nito Bond AR of M/s. Fosroc Chemicals or equivalent approved bonding agent in M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. as per manufacturer's instructions and providing pressure Guniting averaging 30mm thick at a pressure of not less than 6 KG / Sq.cm in Cement Mortar 1:3 duly modifying the mortar with and including suitable bonding agent of M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. @ 5% of weight of cement for soffits of Slabs, Beams, Columns, Fins, Parapets Facias & Chajjas etc., finishing surface rough and finally rendering 15 mm thick in Cement Mortar 1:4 and finishing the top surface even and smooth without using extra cement conforming to proper geometrics including providing double scaffolding and safety measures as required and removal of the same on completion and disposal and depositing the demolished material out of MD land complete all as specified and as directed.

M & L for Cutting / Chipping the spalling concrete surfaces of Slabs, Beams, Columns, Fins, Facias, Parapets & Chajjas etc. and trimming, cleaning the surfaces of any thickness to receive Guniting / Plastering, preparing surfaces and applying a coat of Zinc rich epoxy primer to all steel surfaces as antirust agent and welding steel wire Fabric / Mesh of size 75X25mm of weight not less then 3.0KG per Sq.m to existing reinforcement, applying a coat of Nito Bond AR of M/s. Fosroc Chemicals or equivalent approved bonding agent in M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. as per manufacturer's instructions and providing pressure Guniting averaging 30 to 50mm thick at a pressure of not less than 6 KG / Sq.cm in Cement Mortar 1:3 duly modifying the mortar with and including suitable bonding agent of M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. @ 5% of weight of cement for soffits of Slabs, Beams, Columns, Fins, Parapets Facias & Chajjas etc., finishing surface rough and finally rendering 15 mm thick in Cement Mortar 1:4 and finishing the top surface even and smooth without using extra cement conforming to proper geometrics including providing double scaffolding and safety measures as required and removal of the same on completion and disposal and depositing the demolished material out of MD land complete all as specified and as directed.

S & F in repairs Seamless Calcium Silicate False Ceiling made out of 10mm thick, 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having Phillips head with under head cutter at 200 mm centre to centre, including finishing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish and applying two or more coats of Cement based Wall Care Putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of Acrylic Washable Distemper over a coat of alkali resistant primer and including Frame Work using GI perimeter channels of 0.55 mm thick, having one flange of 20 mm and another flange of 30 mm and web of 27 mm along the perimeter of the ceiling, fixed to wall with nylon sleeves and screws at 450 mm intervals, GI intermediate channels of size 45 mm X 15 mm X 0.90 mm supported with GI ceiling angles of size 25 mm X 10 mm X 0.55 mm fixed to soffits with steel expansion fasteners / GI cleats at 1220 mm intervals, ceiling section of 0.55 mm thick having knurled web of 51.5 mm and two flanges of 26 mm each with lips of 10.5 mm fixed to intermediate channel with connecting clips and in direction perpendicular to the intermediate channels at 457 mm centre to centre complete all as specified and as directed.

M & L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry with 3.0 KG of cement per Sq.m area, rendering 10mm thick in cement mortar 1:3 on concrete surfaces finished even and smooth without using extra cement including mixing of water proofing compound of approved make as per manufacturers instructions for levelling the surface smooth to receive the water proofing membrane, priming the surface with a coat of cold applied bituminous primer @ 0.50 KG per Sq.m, applying a coat of Blown Bitumen of grade 85/25 @ 1.2 Kg per Sq.m, laying Polymeric water proofing membrane of weight not less than 3.00 Kg per Sq.m reinforced with polyester non-woven fabric of weight not less than 150 Grams per Sq.m, by torch application with side over lap of 100mm & end over lap of 150mm & tucked into the chases on vertical surfaces by thermo fusion including applying a coat of Blown Bitumen of grade 85/25 @ 1.2 Kg per Sq.m and finished with a coat of bituminous aluminium paint @ 100 grams per Sq.m on top for water proofing treatment on top for water proofing treatment complete including taking down existing Roof Treatment of any description including PCC padding of any description and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

Supply only Liquid Water Proofing Compound [ISI marked] of approved make.

M & L for applying evenly a tack coat of industrial bitumen of grade 85/25 at the rate of 1.2 KG per Sq.m including cleaning surfaces complete all as specified and as directed.

Dismantling of Floor, Hearth or Wall Tiling of any description including Cement Mortar bedding [but not backing] and removing serviceable tiles to the stores and removing rubbish / debris to a distance not exceeding 1.50 KM complete all as specified and as directed.

M & L for 25 mm thick, PCC 1:2:4, Type B-0, using 10mm graded aggregate as in Sub base for flooring complete all as specified and as directed.

M & L for Hardcore of gauge not exceeding 63mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rolled with power road roller of 8 to 12 ton capacity and consolidated to required gradient and camber complete all as specified.

M & L for 100 mm thick, PCC 1:2:4, Type B-2, using 40mm graded stone aggregate as in Floors / Hard standing / Path etc., surface finished fair and even complete all as specified and as directed.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.11 Sq.m and not exceeding 0.18 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.11 Sq.m and not exceeding 0.18 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Vertical Surfaces such as Skirting, Dado etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Joint Free Glazed Ceramic Tiles, Edge Cut, Concept Type, Coloured, Premium Quality, of size 450 mm X 300 mm, 7 to 8 mm thick as in Vertical Surfaces such as Skirting, Dado etc set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. The colour / shade / design of tiles shall be as approved by GE.

M & L for Vitrified Tiles, Double Charged, Coloured, Premium Quality, of size not exceeding 0.36 Sq.m, 9 to 10 mm thick as in Floors, set and jointed in cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Vitrified Tiles, Double Charged, Coloured, Premium Quality, of size not exceeding 0.36 Sq.m, 9 to 10 mm thick as in Vertical Surfaces such as Skirting, Dado etc, set and jointed in cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red / Z Black / Pearl Black as in Steps, Jambs, Pillars, Window Cills, Cooking Platform etc. and the like with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabs including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: Single stone slab shall be used for entire height of Steps, Jambs, Pillars, Window Cills, Cooking Platform etc. and joints shall match with the flooring

M & L for Glazed Polish finished coloured Chequered Cement Concrete Tiles of thickness 23 to 25mm, made with M-25 Grade Precast Cement Concrete, Hydraulically pressed of size not less than 300 X 300 mm, of approved shape, colour and pattern, set, jointed and pointed in neat cement slurry to match including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed.

M & L for 100 mm thick, PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in Sub base for flooring complete all as specified and as directed.

M & L for Sand Filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M & L for Inter Locking Paving Blocks of 80mm thick, made with M40 Grade cement concrete using 20 mm graded stone aggregate, Hydraulically pressed of approved colour and pattern, shape and size conforming to IS - 15658 set in floors complete all as specified and directed.

S & F Second Class Hard Wood, plain, solid, straight Chowkats and Frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

S & F Factory made, 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S & F Factory made, 35mm thick, Second Class Hard Wood, Plain framed, Panelled Shutter [Two Panel] with Lock Rail and Panel of 9 mm BWP Commercial Ply or 12 mm Veneered Particle Board with Commercial Veneering on both faces, the size of Rail and Stile as per IS – 1003 [Part – I], Kiln Seasoned and Chemically Pressure treated and fitted to Chowkats complete all as specified and as directed.

S & F Factory made, 35mm thick, Second Class Hard Wood, Glazed and Skeleton Shutters, open rebated and prepared to receive glass, gauze, etc. [without Sash Bars], edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part – I, Section 8, Clause 8.24 [a] and fitted to Chowkats complete all as specified and as directed.

S & F Factory made, 35mm thick, Second Class Hard Wood, Glazed and Skeleton Shutters, open rebated and prepared to receive glass, gauze, etc., divided into squares, with plain, chamfered or rounded, mitred and rebated Sash Bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part – I, Section 8, Clause 8.24 [b] and fitted to Chowkats complete all as specified and as directed.

S & F Factory made solid panel PVC door shutter 30 mm thick [Style] consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC "C" Channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement fixing in frame at site as per specification complete all as specified and as directed.

S & F Solid PVC door frame of size 100mmX45mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening complete all as specified and as directed.

S & F Factory made PVC Ventilator made out of multi chamber PVC hollow section DWUF 405 [40x46mm] with 3mm pin headed glass fixed to the lower section using extruded PVC section of 9 X 19.5mm size OL19 with EPDM gasket [SPL 003] for both PVC sections, ventilator's centre mullion shall be made up of multi chamber hollow PVC section DWUF-406 [63.5mmX40mm] with EPDM gasket GL-19 and fixed to the 3 sides of DWUF-405 and DWUF 406 [63.5X40mm] above the centre mullion, Glass panels with aluminium lower set shall be fixed to the frame DWUF-405 on the top of the ventilator for the glass, DWUF 405 and DWUF 406 comers shall be mitred cut and welded, jointed with 12mm MS Rods [Guard Bars] including necessary fixtures complete all as specified and as directed.

S & F Aluminium Powder Coated Sliding Window Frame and Shutters with 91 x 42 x 2 mm thick Three Track section for frames and 39.4 x 17.7 x 2 mm thick Sliding Section for Shutter Frame all round including including necessary Joining Cleats, Glazing Clips, Neoprene Rubber Packing, Powder Coated Aluminium Snap Beading, Screws, Powder Coated Aluminium Fittings such as Locking Arrangement [1 No], Suitable Handle [1 No] including glazing with 4 mm thick Tinted Glass complete all as specified and as directed. Note: [a] Supply only Aluminium Grills will be measured and paid separately. [b] Unit rate quoted shall be deemed to include for cost of fixing only of Aluminium Grills etc.

S & F Powder Coated Aluminium [Minimum thickness of Powder Coating 50 Micron] Glazed Door with Frame made of size 101.60 X 44.75 X 1.75 mm thick Section, Shutters Top Rail and Styles made of size 85 X 44.45 X 1.56 mm thick Section, Middle and Bottom Rail made of size 114.30 X 44.45 X 1.55 mm thick Section including necessary Joining Cleats, Glazing Clips, Neoprene Rubber Packing, Screws, Powder Coated Aluminium Snap Beading, Powder Coated Aluminium Fittings such as Handles, 150mm Dia on both sides, Tower bolts, 200 mm Long [2 Nos], Double Action Floor Spring Hydraulically Regulated made of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty etc. with 5 mm thick Tinted Glass Panel insert, Concealed Locking arrangements complete all as specified and as directed.

S & F Powder Coated Aluminium Deco Grill of Model / Design No. DG 104, fixing the frame as per manufacturers instructions including Powder Coated Aluminium Channel of size 30 X 12 X 5mm for fixing Deco Grill complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment along external walls below concrete or masonry apron using chemical emulsion @ 2.25 litres per RM by drilling 12 mm dia holes up to 300 mm deep and 300 mm centre to centre including plugging holes complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment of soil under existing floors using chemical emulsion @ 1 litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 to match the existing floors complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment at points of contact of wood work by chemical emulsion [in oil or kerosene based solution] @ 0.5 litre per hole by drilling 6 mm dia holes at a downward angle of 45 degrees at 150 mm centre to centre and sealing the same complete all as specified and as directed.

S & F in repairs 18mm thick Plywood, Grade BWR, Type BB, fixed with screws to Wooden Frames complete all as specified and as directed.

S & F Mortise Lock, Vertical type of size 100 mm, 6 Levers with 3 keys of Godrej Make, complete all as specified and as directed.

S & F 100 mm size, Butt hinges, Extruded Aluminium alloy with galvanised mild steel hinge pin, anodised, Type B-21, including fixtures complete all as specified and as directed.

S & F Aluminium anodised barrel Tower Bolt of size 200 mm size of extruded section complete all as specified and as directed.

S & F Aluminium alloy anodised Sliding Door Bolt with hasp and staple [Bolt Type] of size 250 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F Aluminium anodised Handle, of extruded section Fabricated Type of size 150mm long complete all as specified and as directed.

S & F Mild Steel Door Spring 375 mm, Ordinary Rat Rail Rod Pattern springs including roller and roller plate complete all as specified and as directed.

S & F in repairs Decorative type Stainless Steel Curtain Rod of 25 mm dia including PVC rings @ 100 mm centre to centre and Decorative type Stainless Steel Globe type Brackets of size suitable to 25mm dia curtain rod complete all as specified and as directed.

S & F 4mm thick sheet glass ordinary quality and glazing with oil putty or with wooden beads in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

S & F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples or with existing or new wooden beading including necessary painting to beading to match with existing surfaces complete all as specified and as directed.

S & F Stainless steel wire mesh with aperture not exceeding 1.40 mm and dia of wire 0.36 mm and fixed with tinned tacks or stainless steel wire staples with new wooden beading complete all as specified and as directed.

S & F in repairs Stainless steel wire mesh with aperture not exceeding 1.40 mm and dia of wire 0.36 mm and fixed with tinned tacks or stainless steel wire staples with new wooden beading complete all as specified and as directed.

S & F Mild Steel work conforming to Fe - 290, Grade E-165 as in Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes, including Bolts, if required, Hooks [Stay], heavy, for Large Gates, Hook and Pintle Hinges, large Hasps and Staples, Chains, hand made Sliding Bolts, Clamps, Hold Fasts, Wall Ties, Hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles complete all as specified and as directed.

M & L for Preparing surfaces of wood and wood based materials, steel and iron work new or old, of any description and girth not otherwise described, and treating ends of posts, backs of Chowkats, etc. area tarred exceeding 0.1 Sq.m and not exceeding 0.5 Sq.m each with tar or coal tar black paint complete all as specified and as directed.

M & L for Preparing surfaces of wood and wood based materials, steel and iron work new or old, of any description and treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats etc. area tarred not exceeding 0.1 Sq.m each with tar or coal tar black paint complete all as specified and as directed.

Dismantling of Structural Steel work including Doors, Gates etc but excluding framed trusses complete all as specified and as directed.

Dismantling of Plain or Corrugated Steel sheeting of any gauge, thickness of roof in roof coverings, complete all as specified and as directed.

S & F 1.0mm thick Plain, Galvanised, Mild Steel sheeting, in ridges, hips, valley gutters, drip and straight flashings [length and girth as required at site in single piece] with grade of Zinc coating 275 GSM fixed with aluminium self tapping screws, neoprene and EPDM washers of suitable size complete all as specified and as directed.

S & F Bitumastic gola, with 80/25 bitumen and coarse sand mixture. 1:3 by weight, 8cmx8cm at the junction of roofing to vertical surfaces complete all as specified and as directed.

S & F Mild Steel work conforming to Fe - 290, Grade E-165 as in Hand Rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for Balusters Running Bars, for Doors, Balusters, Nosing to Steps including embedding in concrete and screwing etc., Wind Ties for roof including securing bolts, Posts and Struts in Fencing including cutting tops to shape as directed, bending to shape, notching for wire, drilling holes or as in flat iron fillets [for securing wire mesh and barbed wire etc.] including all necessary drilling, bolting or riveting, etc. and similar work complete all as specified and directed.

M & L for preparing surfaces of Floors and Walls of Water Closet, Bathrooms, Kitchens etc. and applying Polymer Modified Non Shrinking Slurry using Brush Bond Powder and Nitobond BB Acrylic Emulsion drilling holes at 300mm interval to a depth of 60 mm, 20mm dia and filling with Rendroc Plug, finally filling the joints of tiles with Ntolite complete all as per manufacturer's instructions complete all as directed. Note: Each Woter CLoset Area, Bath Room Area and Kitchen Area shall be mesured as one unit] Make of Chemicals specified here-in-above: M/s. Fosroc Chemicals India [P] Ltd. or its equivalent in M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Batik India Pvt. Ltd.

S & F in repairs Steel rolling shutters, thickness of laths of 1.25 mm, with ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, Push and Pull Type complete all as specified and as directed.

S & F in repairs Steel rolling shutters, thickness of laths of 1.25 mm, with ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, Gear Operated Type with bevel gear box and crank handle, complete all as specified and as directed.

Repairs and servicing of Rolling Shutters for smooth and trouble free operation and remving of worn out components such as hood cover, laths, ball bearings, helical wire springs. Lock plates, brackets, plates, shaft rod etc. including greasing and refixing the same in position complete all as specified and as directed. Note: Spares required if any shall be measured and paid separately as supply only.]

Supply only Safety Lever Lock Mild Steel with 4 Levers suitable for rollong shutters complete all as specified and as directed.

Supply only 450mm long Helical Wire Spring made of 7.5mm dia wire complete all as specified and as directed.

Supply only 300mm long Helical Wire Spring made of 6.4mm dia wire complete all as specified and as directed.

Supply only Ball Bearing of size 50/65mm dia suitable for rollong shutters complete all as specified and as directed.

Supply only Rolling Shutter Shaft made of MS ERW Pipe, 50 mm bore, Medium Grade, conforming to IS – 1239 complete all as specified and as directed.

Supply only Rolling Shutter Hood Cover made of 1.00 mm thick CRCA Sheet, bent to shape to match with existing brackets including MS Angle / Flat Stiffeners complete all as specified and as directed.

Supply only Interlocking Lath Section made of 1.00 mm thick CRCA Sheet, in single piece to match with existing and fitted with automatic lock section fitted with melleable mild steel clips on eiyher side and duly shop coated of primer complete all as specified and as directed.

Supply only Interlocking Lath Section made of 1.25 mm thick CRCA Sheet, in single piece to match with existing and fitted with automatic lock section fitted with melleable mild steel clips on eiyher side and duly shop coated of primer complete all as specified and as directed.

Supply only Lock Plate of 125mm width made of 3,15 mm thick MS Sheet welded with Angle Iron of 35 X 35 X 3 mm frame at bottom complete all as specified and as directed.

Supply only Gear Mechanically Operated with Spur Wheel Gear and Bevel Gear Box complete all as specified and as directed.

Supply only MS Guide Channel of 3.15mm thick and 65mm wide complete all as specified and as directed.

Repairs and servicing of Collapsible Steel Gate for smooth and trouble free operation and remving of worn out components such as Guide Rails, Channel Pickets, Pivoted Flat Bars, Top and Bottom Runners, Handles Rivets, Rollers, Wheels, Verticle Channels etc. straightening of vertical channels, cleaning of rust including greasing and refixing the same in position complete all as specified and as directed. Note: Spares required if any shall be measured and paid separately as supply only.]

Supply only Collapsible Steel Gate spares / worn out components such Guide Rails, Channel Pickets, Pivoted Flat Bars, Top and Bottom Runners, Handles Rivets, Rollers, Wheels, Verticle Channels etc. complete all as specified and as directed.

S & F in repairs Collapsible Steel Gates, Top Hung, consisting of Channel Pickets, Pivoted Flat Bars, Top and Bottom Runners, Brass Handles etc. as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and as directed.

M & L for 20 mm thick, Wear proof toping using approved Non-Metallic Floor hardner @ 5 KG per Sq.m laid on concrete floors / Pavings when the base concrete is stiffened to the point when the light foot traffic leaves an imprint of 3mm thick, surface finished even and smooth over 40 mm average thick, PCC 1:2:4, Type B-1, using 20mm graded aggregate as in flooring complete as per manufacturer's instructions complete all as specified and as directed.

Taking down Aluminium / UPVC Window shutter of any description / size and any numbers from each window and refixing in the same opening after cleaning Glass and Wiremesh shutters using mechanical / vaccume cleaners complete all as specified and as directed.

M & L for preparation of newly plastered wall surfaces and applying two coats of Cement Based paint over a coat of Alkali Resistant Primer complete all as specified and as directed.

M & L for preparing newly plastered wall surfaces and applying two coats of Acrylic Washable Distemper over a coat of alkali resistant primer complete all as specified and as directed.

M & L for preparing newly plastered ceiling surfaces and applying three coats of white washing complete all as specified and as directed.

M & L for preparation of old plastered or unplastered surfaces including brooming down or steel wire brushing and applying one coat of white wash on walls complete all as specified and as directed.

M & L for preparation of old plastered or unplastered surfaces including brooming down or steel wire brushing and applying two coats of white wash on walls complete all as specified and as directed.

M & L for preparation of old plastered or unplastered surfaces including brooming down or steel wire brushing and applying one coat of white wash on ceilings complete all as specified and as directed.

M & L for washing, rubbing down and stopping of distempered and painted surfaces of walls and applying one coat of Acrylic Washable Distemper on wall surfaces complete all as specified and as directed.

M & L for Complete removal of existing treatment of any description on wall / Ceiling surfaces and applying two or more coats of Cement based Wall Care Putty on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of Acrylic Washable Distemper over one of alkali resistant primer on wall / Ceiling surfaces complete all as specified and as directed.

M & L for preparation of old painted wood and wood based surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for preparation of old painted wood and wood based surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for washing, rubbing down and stopping of painted surfaces of walls and applying one coat of Plastic emulsion paint on wall surfaces complete all as specified and as directed.

M & L for washing, rubbing down and stopping of painted surfaces and applying one coat of cement based paint on walls complete all as specified and as directed.

M & L for washing, rubbing down and stopping of painted surfaces and applying One coat of Weather Proof Exterior Emulsion Paint [100% Acrylic] on Walls complete all as specified and as directed.

M & L for Complete removal of existing treatment of any description on walls and applying two or more coats of Cement based Wall Care Putty on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] over a Coat of Weather Proof Exterior Primer of same manufacturer as that of paint on walls complete all as specified and as directed.

M/s SIRI CONSTRUCTIONS

RAMESH ASSOCIATES

Mavee Syndicate