Providing CAD component works for Lift irrigation schemes Baddu Glassin under HIM CAD Jal Shakti Division Ghumarwin in Tehsil Ghumarwin Distt Bilaspur CO of 15 Nos outlets Hydrants and laying jointing testing of HDPE pipe

Amount

Excavation in foundations and trenches (for pipes and pits in all depths etc) in pick work,jumper work the excavated earth within all leads and lifts clear from the edge of excavation and then returing the stacked soil in 15cm layers when required into sides of foundation and trenches etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by Engineer-in-charge with in all leads and lifts including uprooting of trees,dressing of beds and sides and preparation of sub grade,restoration of unmetalled/metalled/paved surfaces to its original conditions including soring,strutting, and timbering where ever required providing diversions for traffic,fixing night signals, fixing caution boards,crossing over trenches for access to houses complete and to the entire satisfaction of the Engineer-in charge.

Laying,jointing &testing HDPE pipe of following diameter and class as per IS 4984-2016 grade PE-80 High density polyethylene pipes butt heat fusion welding joint process i/c all necessary fittings & bends etc as required complete in all respect with carriage in all leads & lifts as per direction and to the entire satisfication of Engineer in Charge (Earth work in trenches to be measured and paid for seperately.

110mm dia PN-4.00

160mm dia PN-4.00

180mm dia PN-4.00

Providing and laying cement concrete 1:4:8 (1cement: 4sand: 8 graded stone aggregate 40mm nominal size) excluding the cost of centering and shuttering in foundation and plinth in all lead and lifts and to the entire satisfaction of the Engineer-in-charge

Providing and laying cement concrete 1:1.5:3 (1cement: 1.5sand: 3 graded stone aggregate 20mm nominal size) and curing complete excluding the cost of form work & reinforced concrete work in:- and to the entire satisfaction of the Engineer-in-charge

Foundation, footing, bases of columns and the like & mass concrete

Suspended floor,roofs,landings & shelves and their supports, balconies, girders, bressumers & cantileverup to floor to level in all leads and lifts

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and cent ring below supporting floor to ceiling not exceeding 4 mtr and removal of the same for in-situ reinforced concrete and plain concrete work in all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pilasters buttresses, plinth and string courses and the like.

Flat surfaces such as soffits of suspended floor roof landings and the like up to 200mm in thickness.

Providing & placing Tor steel reinforcement for RCC work i/c bemding, binding & placing complete upto floor two level.

providing & placing precast concrete socketed & spigote pipe of 900 mm dia & 1.20 mtr in length class NP-2 reinforcement duly ISI marked as per IS 458-2008 with latest amendments if any , complete with Rubber rings type-II duly ISI marked as per IS 5382-1985 i/c carriage in all leads & lifts completes in all respect of following dia:-

providing & placing precast concrete socketed & spigote pipe of 350 mm dia & 0.75 mtr in length class NP-2 reinforcement duly ISI marked as per IS 458-2008 with latest amendments if any , complete with Rubber rings type-II duly ISI marked as per IS 5382-1985 i/c carriage in all leads & lifts completes in all respect of following dia.

Providing boulder filling dry hand packed tightly in hydrants chamber as per direction of Engineer-in -Charge.

Providing Earth filling in Hydrants chamber with in all leads & lifts

Providing and installation of 80 mm dia control valve including removable connceting rod and other Equipments like HDPE pipe, tamper proof thimble and chain lock etc. as required for hydrants complete in all respect as per direction of Engineer-in- Charge.

BITTU RAM

Mohit Kaushal

Rakesh Kumar Sharma