Repair to leakage/seepage, joinery, flooring, ceiling, sanitary fitting, plastering, painting, approach path, drain and internal electrification of Offrs Md Accn at SP Road/Beacher Road under GE Dehradun

Amount

M&L non skid / mat finish ceramic colour tiles of size 300 mm x 300 mm and 6- 7 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:4 and dismantling of existing floor tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

M&L non-skid / mat finish designed coloured joint free ceramic tiles of size not less than 400 mm x 400 mm x6- 7 mm thick in floor, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed in cement mortar 1:6 and dismantling of existing tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

All as per item No 2 above but as in skirting including 10 mm thick rendering in cement mortar 1:4, complete all as specified and directed.

M&L glazed ceramic colour tiles size 300 mm x 450 mm x 6-7 mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick rendering in cement mortar 1:4 and dismantling of existing wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

M&L vitrified ceramic coloured tiles 10 mm thick (square/rectangular) polished,area of each tiles not exceeding 0.36 sqm, in floor etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 and dismantling of existing floor tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

All as per item No 5.00 here in above but as in skirting and including 10 mm thick rendering in cement mortar 1:4, complete all as specified and directed.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M & L 25 mm thick PCC 1:2:4 type B-0 using 12.50 mm graded stone aggregate as in leveling course to floors complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in plinth protection or similar work/places, laid in alternate bays and filling the joints with & including bitumen and sand 1:3 by weight, surface finished even and fair without using extra cement complete all as specified and directed.

M&L 40 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in flooring, laid in alternate bays, surface finished even and smooth with using extra cement complete all as specified and directed.

M&L 18 to 20 mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete including demolition of stone slab all as specified and directed.

M&L heavy duty endura ceramic coloured tiles 10 mm thick dark shade (square/rectangular) polished,area of each tiles not exceeding 0.36 sqm, in floor etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 and dismantling of existing floor tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Taking down and re-fixing the existing shutter in same opening after & including necessary easing/repair etc. exc. 1 Sqm but n. exc. 2 Sqm each complete all as specified and directed.

Taking down and re-fixing the existing shutter in same opening after & including necessary easing/repair etc.n exc. 1 Sqm complete all as specified and directed.

Taking down shutter of any description, n. exc. 1 Sqm each and removing from site complete all as specified and directed.

All as per item No 15.00 here in above but exc. 1 Sqm but n. exc. 2 Sqm each and removing from site complete all as specified and directed.

Taking down chowkhats or frames n. exc 1.5 sqm each without taking off shutter from the frame complete all as specified and directed.

All as per item No 17.00 here in above but exc. 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

S & F second class hardwood (Golden Teak) plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at jointscomplete all as specified and directed.

S & F 35mm thick second class hardwood (Golden Teak) glazed and Skelton factory made door shutters, open rebated and prepared to receive glass/gauze etc divided into squares with plain, chamfered or rounded mitered and rebated sash bars, edges of framing plain, chamfered, fitting with cut and rebated beads for securing glass/ gauge complete all as specified in SSR Pt I-2009 section 8 clause 8.24 (a) and as directed.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed.

S & F 30 mm thick second class hardwood (Golden Teak) glazed and Skelton factory made window/ventilator shutters, open rebated and prepared to receive glass/gauze etc divided into squares with plain, chamfered or rounded mitered and rebated sash bars, edges of framing plain, chamfered, fitting with cut and rebated beads for securing glass / gauge complete all as specified in SSR Pt I-2009 section 8 clause 8.24(b) and as directed

All as per item No 22.00 here in above but 30 mm thick without shash bar for window/ventilator shutter all as specified and directed in SSR Part-I clause 8.24 b.

S&F 30 mm thick moulded WPC factory made 100% solid door (conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side palin with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire etardant and having screw holding capacity complete all as specified and directed.

S&F factory made 100 % solid wood plastic composite (WPC) door frame 75x50 mm made from wood plastic composite (single extruded process) material with density 780 Kg/Cum from ISO certified company door should be water proof, termite proof, fire retardant and having good screw holding capacity all as per specification and drawing as directed by Engineer-in-Charge

S&F Pressed steel frames of size 105x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.(Note: framed filled in cement concrete1:2:4 type B0 ( 12.5 mm stone aggregate)

S&F Pressed steel frames of size 125x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.(Note: framed filled in cement concrete1:2:4 type B0 ( 12.5 mm stone aggregate)

M&L mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, ball bearing and other similar works etc, complete, drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding complete all as specified and directed.

S&F mild steel, plain, black sheet 0.80 mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitered angles, etc. as required complete all as specified and directed.

S & F factory made steel window with side hung shutters including box type hinges with steel handle, steel peg stay,tower bolt etc. complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F factory made steel window with side hung shutters including box type hinges with steel handle, steel peg stay, tower bolt etc.complete without glazing bars, dovetailed or welded complete all as specified and directed.

S & F factory made steel ventilator with top hung shutters including hinges with steel handle, steel peg stay, tower bolt etc.complete all as specified and directed.

S&F stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in square area n. exc. 0.5 Sqm in each pane complete all as specified and directed.

S&F in repair stainless steel wire 0.56 mm nominal dia of wire and average width of aperture 1.40 mm as in wooden or metal frame of any description complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 including necessary welding, drilling hole complete all as specified and directed.

S&F factory made 100 % solid wood plastic composite (WPC) flush type shutter of 18mm thickness one side laminate consisting of panel of PVC profile of 18mm (+ 0.7mm) thick of denisity 600 kg per cum manufactured by ISO-9000 certified company using for shutter cillicia ply 18mm thick and fixed with frame. The thickness of shutter is edges painted by matching colour of PVC lining of plain/prelim coloured PVC sheet using etc complete as per manufacture specification.

S&F magnetic catcher and striking plate and brass body 140 mm length including letting in and fixed complete all as specified and directed.

S&F Continious (PIANO) hinges, mild steel, bright finish or electrogalvanised. 30 mm width of flaps (when open) complete all as specified as directed.

S & F stainless steel barrel tower bolts 150 mm long one piece and fixed complete all as specified and directed.

S & F stainless steel barrel tower bolts 200 mm long one piece and fixed complete all as specified and directed.

S & F stainless steel butt hinges, medium weight 75 mm long one piece and fixed with screws/welded to frame ,complete all as specified and directed.

S & F stainless steel butt hinges, medium weight 100 mm long one piece and fixed with screws/welded to frame complete all as specified and directed.

S & F stainless steel handles 150 mm long one piece and fixed with screws/welded to frame ,complete all as specified and directed.

S & F stainless steel handles 125 mm long one piece and fixed with screws/welded to frame ,complete all as specified and directed.

S&F Hasp and staple 75mm safety type, stainless steel with hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S & F 300 mm long stainless steel sliding door bolt (bolt not less than 12 mm dia) with hasp & staple and fixing clips of SS sheet, and SS fixing bolts and fixed complete all as specified and directed.

M & L floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, fixed to floor of size 140 mm complete all as specified and directed.

S & F 300 mm stainless steel, ordinary rat tail rod pattern spring welded to steel/fixed to wooden door frame including roller and roller plate complete all as specified and directed.

S & F in repair stainless steel barrel tower bolts 200 mm long one piece and fixed complete all as specified and directed.

S & F in repair stainless steel butt hinges, medium weight 75 mm long one piece and fixed with screws/welded to frame ,complete all as specified and directed.

S & F in repair stainless steel butt hinges, medium weight 100 mm long one piece and fixed with screws/welded to frame ,complete all as specified and directed.

S & F in repair stainless steel handles 150 mm long one piece and fixed with screws/welded to frame complete all as specified and directed.

S & F in repair stainless steel handles 125 mm long one piece and fixed with screws/welded to frame , complete all as specified and directed.

S&F in repair Hasp and staple 75mm safety type, stainless steel with hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S & F in repair 300 mm long stainless steel sliding door bolt (bolt not less than 12 mm dia) with hasp & staple and fixing clips of SS sheet, and SS fixing bolts and fixed complete all as specified and directed.

S&F in repair floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, fixed to floor of size 140 mm complete all as specified and directed.

S & F in repair 300 mm stainless steel, ordinary rat tail rod pattern spring welded to steel/fixed to wooden door frame including roller and roller plate complete all as specified and directed.

S&F auto closing hinges 35 mm of 0 crank( KH-001) OR 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete all as specified and directed. Make :Hexa, Hettich, Hafele

S&F Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kgs complete all as specified and directed.

S&F in repair chrome plated stainless steel wire basket (storage basket) pull out type for large utensils, size 480 x 500 x 150 mm of Grade 304 with necessary fixing clips etc. complete in all respect as specified and as directed by engineer- in – charge.

S&F in repair chrome plated stainless steel wire basket (cup and saucer basket) pull out type, size 380 x 500 x 100 mm Grade 304 with necessary fixing clips etc. complete in all respect as specified and as directed by engineer- in – charge.Make :Hettich, Hafele, Butterfly

S&F in repair chrome plated stainless steel wire basket (plate basket) pull out type, size 380 x 500 x 100 mm Grade 304 with necessary fixing clips etc. complete in all respect as specified and as directed by engineer- in – charge.Make :Hettich, Hafele, Butterfly

S&F in repair chrome plated stainless steel wire basket (cutlery basket) pull out type, size 380 x 500 x 100 mm Grade 304 with necessary fixing clips etc. complete in all respect as specified and as directed by engineer- in – charge.Make : Hettich, Hafele, Butterfly

S&F in repair chrome plated stainless steel wire basket (Grain Trolley) pull out type, size 480 x 500 x 200 mm Grade 304 with necessary sliding frame structure, fixing clips etc. complete in all respect as specified and as directed by engineer- in - charge. Make : Hettich, Hafele, Butterfly

S&F in repair chrome plated stainless steel wire basket (Bottle pull out) pull out type two self, size 120 x 500 x 432 mm with necessary sliding frame structure, fixing clips etc. complete in all respect as specified and as directed by engineer- in – charge.” Make : Hettich, Hafele, Butterfly

M & L applying two coats of Synthetic paint on new wooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified and directed.

M & L preparation of old painted surfaces of wood & wood based material of any description over 10 cm width or girth and applying one coat of synthetic enamel Paint complete all as specified and directed.

Dismantling of Asbestos cement (corruga ted, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and profile should match with galvalume sheet complete all as specified and as directed..

Dismantling of framed or unframed timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed

S&F for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe 410-W(Gde E-250) quality-A complete all as specified and directed

M & L applying two coats of synthetic enamel paint on new or previously untreated steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete all as specified and directed.

M & L applying one coat of synthetic enamel paint on old painted steel surfaces of any description including preparation of steel surfaces complete all as specified and directed.

S&F in repair SS grade 204 drapery rod 25 mm dia including decorative brackets, decorative finals at both ends complete all as specified and directed.

Taking up or down steel tubing and connection incl removal from site bore of pipe 15mm complete all as specified and directed.

Taking up or down steel tubing and connection incl removal from site bore of pipe 20mm complete all as specified and directed.

Refixing of old steel tubing and connections in new or old position with all new fittings to floor, wall or ceiling as directed, for 15mm bore GI tubing complete all as specified and directed. .

Refixing of old steel tubing and connections in new or old position with all new fittings to floor, wall or ceiling as directed, for 20mm bore GI tubing complete all as specified and directed. .

S&F 15mm bore pipe medium grade galvanised iron with all fittings fixed to wall and ceiling or laid in floor complete all as specified and directed by Engr-in-Charge.

S&F 20mm bore pipe medium grade galvanised iron with all fittings fixed to wall and ceiling or laid in floor complete all as specified and directed by Engr-in-Charge.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth complete all as specified and directed.

S&F in repairs PVC connection 15 mm dia 450 mm long with brass fly nut at both ends complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including cantilever brackets of suitable angle iron,CP brass waste coupling ,superior quality PVC waste pipe and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including cantilever brackets of suitable angle iron,CP brass waste coupling ,superior quality PVC waste pipe and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S & F in repairs, vitreous china wash down water closet pedestal pattern white (excluding flushing cistern and flush pipe) with CI ‘P’ or ‘S’ trap including plastic white sheet cover, CP jet spray with 1.0 metre long PVC pipe, connecting to stack pipe and to flushing pipe and complete including making good to floor complete all as specified and directed.

S & F in repair vitreous china squatting pan “ORISSA PATERN” of size 580 mm x 440 mm, white, with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete all as specified and directed.

S&F in repairs Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S & F in repair 10 litre capacity PVC low level cistern ‘ white’ with inlet, float valve including brackets with 32 mm dia PVC pipe/bend 600 mm long complete all as specified and directed.

S & F in repair75 mm bore UPVC (SWR) pipe pressure 4kgf/cm2 single socketed in any length with rubber ring, fixed on wall / laid in trenches complete all as specified and directed.

S & F in repair 110 mm bore UPVC (SWR) pipe pressure 4kgf/cm2 single socketed in any length with rubber ring, fixed on wall/ laid in trenches complete all as specified and directed.

S & F in repair 75 mm bore UPVC (SWR) bend with oval acess door ,'T'socket reducer etc complete all as specified and directed.

S & F in repair 110 mm bore UPVC (SWR) bend with oval acess door ,'T'socket reducer etc complete all as specified and directed.

S&F in repairs heavy duty thread type PVC water tank cover with fixing frame fixed on PVC tank with 4 Nos of screws for 500/1000 ilts tank complete all as specified and directed by the Engr-in-Charge.

S & F in repair vitreous china wash hand basin white, flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of waste fitting etc complete all as specified and directed. Make : Jaquar (CNS-WHT-301) or equivalent Hindware/ Parryware.

S&F in repair CP brass 3 in 1 hot & cold 15 mm dia wall mixer for mixing hot and cold water with telephonic shower provn with connecting legs &flanges complete all as specified and directed. Make : Jaquar Model No CON 281KN, HSH 1929 & OHS 1989/Marc ES547A & ES 531 (Telehone shower) ES 549 (shower) ES 536 (Shower).

S&F in repair 15mm dia brass chromium plated centre hole wash basin/ sink mixer with accessories in wash basin for mixing hot and cold water, screwed down for 15 mm dia bore GI Pipe complete all as specified and directed. Make : Jaguar CAT Part No SOL-6001B/Hindware CAT Part No F450009/Parryware CAT Part No G0665A1

S&F in repair brass chromium plated ovehead shower with shower arm complete all as specified and directed. Make : - Parryware Cat Part No T9985A1(Shower) & T-9999A1(Arm)/Hindware Cat Part No F160054 (Shower) & F190016(Arm)/Jaquar Cat Part No OHS 1999 (Shower) & SHA479L300 (Arm).

S&F in repair 15 mm bore Angle cock/stop valves, cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed. Make : - JAGUAR Cat Part No FON-40053/Hindware Cat Part No F160017/Prayag Cat No 9410

S&F in repair 15mm bore Bib taps long body cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make : - JAGUAR CAT Part No ALI-85037/Hindweare CAT Part No F-370004/Prayag CAT Part No S9906

S&F in repair CP Health Faucet with 1.20 mtr metalic expandable tube & hook complete all as specified and directed. Make : Jaquar Cat No.ALE-ESS-585/Parryware Cat No. T9941A1 or equivalent to Hindware .

Supply and fix in repair CP grating 100mm to 125 dia round fix on floor trap/ nahani trap with hole/without fixed with cement mortar, complete all as specified and directed.

S&F in repair looking mirror mounted on decorative type PVC frame fixed to wooden plug with CP brackets screw fixed, complete all as specified .

S & F in repair 20 mm dia brass chromium plated towel rack of 3 sets type 60cm long between flanges including pair of fixing brackets complete all as specified and directed. Make: Jaquar Cat Part No AKP-35781PS/CAN-1181FHS

S&F in repairs brass chromium plated towel ring complete all as specified and directed. . Make : Jaquar Cat No.AQN-7721 or equivalent to Hindware/ parryware.

. S&F in repairs chromium plated Toilet paper holder complete all as specified and directed. Make : Jaquar Cat No.ACN -1151N or equivalent to Hindware/ parryware.

supply and fix in repairs brass spindle for bib tap, pillar tap, stop cock,angle valve, wall mixture and basin mixture of any description etc, complete all as specified and directed.

S&F in repair 32/40 mm Waste fittings/coupling, brass, chromium plated for sinks, etc. with long screwed shanks and fly-nuts complete all as specified and directed.

S&F in repair 32 mm Waste fittings /coupling brass, chromium plated for wash hand basin, etc. with long screwed shanks and fly-nuts complete all as specified and directed.

Supply and fix in repair 32 mm dia PVC waste pipe for WHB and sink 90 cm long with union, complete all as specified and directed.

M&L cleaning of water storage tank capacity exceeding 250 litres but not exceeding 500 litres, mechanically using pressure pump with disinfectant chemical including cleaning & removing all scale & dirt etc from existing tanks, mouths of circulating pipes and outer surface of any description & washing down in the manner complete all as specified and directed.

M&L cleaning of water storage tank capacity exceeding 500 litres but not exceeding 1000 litres, mechanically using pressure pump with disinfectant chemical including cleaning & removing all scale & dirt etc from existing tanks, mouths of circulating pipes and outer surface of any description & washing down in the manner complete all as specified and directed.

S & F rotational moulded polyethylene water storage tanks Capacity of tank 500 litres tripple layer, white colour, (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-2009 including dismantling of existing unserviceable tank and removing from site, complete all as specified and directed.

S & F rotational moulded polyethylene water storage tanks Capacity of tank 1000 litres tripple layer, white colour, (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-2009 including dismantling of existing unserviceable tank and removing from site, complete all as specified and directed.

M & L in repair 75 mm CI spun casted floor trap with grating including jointing with solvent cement 75mm bore outlet complete all as specified and directed.

S & F in repair ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 15 mm bore size (Minimum weight 142 gms), complete all as specified and directed.

S & F in repair ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (Minimum weight 210 gms) complete all as specified and directed.

S&F in repair of Aluminium body door cill at bottom part of door to stop entry of insect inside the room complete all as specified and as directed.

Providing & fixing false ceiling of Designer tile Ivory painted (High Pressure Steam cured) of 4mm thickness (as per IS : 14862) of size 595x595mm and any one of the design (Cascade or electra) in true horizental level, suspended on inter locking metal grid of hot dipped galvanised steel section (Galvanised @120 grms, both side inclusive and black painted groove on all T webs) consisting of main T runner with suitably spaced joints to get required length and 15x32mm made from 0.30mm thick sheet spaced at 1200mm c/c and croos 'T' of size 15x32mm made of 0.30mm sheet 1200mm long spaced between main "T" at 600 mm c/c to form a grid of

All as per item No 121 (Contd/--) ...1200x600mm and secondary cross "T" of length 600mm and size 15x32 mm made of 0.30mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable wire of 4mm dia with galvanised butterfly level clips, spaced at 1200mm c/c along main 'T', bottom exposed width of 15mm of all 'T'' sections of 4mm dia GI wire shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5mm width, including taking down existing ceiling of any type all complete at all heights as per direction of Engineer-in-Charge.

M&L for cleaning of existing seawage pipe line 100mm /150mm/200mm internal dia at any depth including manholes by removing the manhole cover of any type/size and cleaning by means of hydraulic jet pressure machine/ manually (as directed by Engr-in-charge) as required at site from manhole and well flushing with water after cleaning including getting out sludge and disposal out of defence land , refixing the manhole in original complete all as specified and directed

M&L cleaning the blockage of bathroom/ kitchen by cleaning the nahani traps/ gully traps of all the mud /sludge and getting out, washin thoroughly grating of trap,CI waste pipes by opening the clearing eyes and deposting the sludge in a pit of suitable size at a distance not exceeding 50 meters form the gully trap and covering the same with the soil obtained from excavation of pit including all excavatons and earthwork complete all as specified and directed by Engr-in-Charge.

M&L cleaning of blockage of WC indian or European type by removing of all the mud/sludge and getting out depositing the sludge in a pit of suitable size at a distance n exc 50 mtr from the WC excavations and earth work complete all as specified and directed by Engr-in-Charge.

Cleaning of manholes any depth any size taking out accumulated, soil, sludge any material incl both ends and removal to MD lands and manhole cover refixing complete all as specified and directed by Engr-in-Charge.

Sucking out sewage water through sewage tanker from the man hole/septic tank/soakage well in different location and disposing off out of MD land as directed by Engr-in-Charge. Notes. For cleaning of sewage system:- (a) Contractor's representative shall attend office of Engr-in-Charge on all working days at 0900 hrs to collect the complaints pertaining to blockage of traps, cleaning of sewage lines, manholes, septic tank and soak wells . In case contractor's representative fails to report Rs 450/- per day will be deducted from the contractor payment for the absent period. (b) complaint slips shall be deposited to the JE concerned after completion of job duly singed by the users. payment shall be made on the basis of complaint slips and site verification by JE/ Engr-in-Charge. (c) Contractor shall provide printed complaint register/ slip as per format given by Engr-in-Charge before commencement of work. (d) The work in foul conditions such as cleaning of soakwell, septic tanks, manholes etc shall be carried out with mechanical means where work with mechanical means is not practicable and work shall be executed manually with the permission of Engr-in-Charge.

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre depth for foundation, manhole etc not exc 10 Sqm on plan and not exc 1.5 metre in depth including getting out in soft/loose soil complete all as specified and directed by Engr-in-charge

Returning, filling in including spreading, leveling watering and well ramming in layers not exceeding 25 centimetre in soft/loose soil complete all as specified and directed by Engr-in-charge

Removing excavated surplus soil/material not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed by Engr-in-charge

Demolition and breaking up drain pipes (SGSW, AC or reinforced concrete) 150mm bore set in cement mortar complete all as specified and directed.

S&F 150mm internal dia salt glazed stoneware drain pipe Gde 'A', laid in trenches and jointed in cement & sand mortar 1:1, complete all as specified and directed.

M&L for in PCC (1:3:6) type C-2 (using 20 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and directed.

Demolition of reinforced cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified

Use and waste Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) of fair finished surfaces complete all as specified and as directed.

M & L for RCC (1:2:4) B1 (using 20 mm graded stone aggregate) as in slabs supported on wall, beam and columns in floors ,roof slabs, shelves and cover slab Including demolition of existing old RCC complete all as specified and as directed.

S & F mild steel TMT bar 8 mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M&L for 65 mm thick vibromatic reinforced precast cement concrete 1:1:2 (using 20mm graded stone aggregate) with 2mm thick mild steel CR sheet around painted with 2 coats of bituminous paint , as in man hole cover slabs finish fair even and smooth without using extra cement ( Top surface will be chequred finish) including necessary form work, 100 mm long handle of 12mm dia round bar counter sunk by 25mm welded to reinforcement complete all as specified and directed by Engr-in-charge (Note : CA No and date will be engraved on covers. Reinforcement shall be measured and paid saperately. Curing will carried out with ponding method)

Cutting into existing manholes for connecting new drains 150mm dia making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required complete al as specified and directed.

Excavating in post holes (or similar holes) each n.exc 0.5 cum, getting out, removing surplus soil to a distance n exc 50m and making good surface in hard/dense soil complete all as specified and as directed by the Engr-in-Charge.

S&F mild steel work as in post and strut in fencing including cutting tops to shape as directed drilling holes, notching for wire etc. and flat iron fillets, 10 mm dia round bar, nut & bolts for securing wire mesh including all necessary drilling and bolting including embeding in concrete and similar work confirming to Fe-290 Gde E-165 complete all as specified and directed.

Supply only Chain link MS galvanised fencing any size or type weight exc 4 Kg per square metre as approved by Engineer-in-Charge.

Fixing only Chain link fencing including line wires, any mesh size and type to any type of standards rails straining bolts etc including provision of binding wireany size or type weight exc 4 Kg per square metre as approved by Engineer-in-Charge.

S&F in repair Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed.

Dismantling fencing wire mesh, any type complete all as specified and directed.

M & L PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation filling, mass concrete, sub base or leveling course of floor etc complete all as specified and directed.

M & L PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in surface channel and drain including necessary use and waste of form work complete all as specified and directed.

Demolition of Brickwork or stone/bou-lder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L brick work with sub class 'B' brick straight or curved on plan exc. 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L brick work with sub class 'B' brick straight or curved on plan to any radius built in cement mortar 1:4 as in half brick thick wall including demolition of existing brick work or stone masonary built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed.

M & L 15 mm thick rendering on brick work or concrete surface in cement mortar 1:6, surface finished even and fair complete all as specified and directed.

M & L 15 mm thick rendering in cement mortar 1:4 on brick work or concrete surface, surface finished even and fair complete all as specified and directed.

M & L 10 mm thick rendering on ceiling surface in cement mortar 1:3 mixed surface finished even and smooth complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls (plastered) by brooming down with coir wire brushing, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and finally clean with sand paper all as directed by Engr-in-Charge.

Complete removal of existing treatment of wall by mechanised method and preparation of surface of wall and applying 2-3 mm thick of exterior grade acrylic water proof wall care putty and applying one coat of exterior water based primer by using Airless spray techonology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressue and paint usage and certified by jpaint manufacturer and as mentioned in PS and accessories fpr applying distemper, should be able to spray in hard to reach areas and penetration of distemper, on the surface to achieve excllent application using limited manpower complete all as specified and directed. Note : - Sanding of old decorated surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer complete all as specified and directed.

Complete removal of existing treatment of wall by mechanised method and preraration of surface and applying 2-3mm thick of white wall care putty and applying one coat of primer by using Airless spray techonology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressue and paint usage and certified by jpaint manufacturer and as mentioned in PS and accessories fpr applying distemper, should be able to spray in hard to reach areas and penetration of distemper, on the surface to achieve excllent application using limited manpower complete all as specified and directed. Note : - Sanding of old decorated surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer complete all as specified and directed.

M&L for applying one coats of oil bound distemper on already prerared surface of wall using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed. Note : - Sanding of surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer complete all as specified and directed.

M&L for applying two coats of oil bound distemper on new/already already prepared plastered surfaces of walls using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed. Note : - Sanding of surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer complete all as specified and directed.

M&L for applying two coat of exterior weather proof 100% anti fungal acrylic smooth emulsion with silicon additives that offer anti alge high performance exterior wall finish with 6 years of performance warranty by manufacturer applied by using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacture with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper, should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed.

M&L for applying one coat of exterior weather proof 100% anti fungal acrylic smooth emulsion with silicon additives on already prepared surface of wall, AC Sheet etc that offer anti alge high performance exterior wall finish with 6 years of performance warranty by manufacturer applied by using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacture with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper, should be able to spray in hard to reach areas and penetration of emulsion on the surface to achieve excellent application using limited manpower complete all as specified and directed.

M & L for one coat of white wash on already prepared surfaces of walls complete all as specified and directed by Egnr-in-Charge.

M & L for one coat of white wash on already prepared surfaces of ceiling complete all as specified and directed by Egnr-in-Charge.

M&L preparation of old decorated surfaces of ceiling (Plastered) by brooming down or sand paper, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots complete all as specified

M&L for preparation of newly plastered surface of wall and applying two coat of cement base paint over a coat of primer complete all as specified

M&L for preparation of newly plastered surface of wall and applying three coat of white wash complete all as specified

M&L for preparation of newly plastered surface of ceiling and applying three coat of white wash complete all as specified

S&F in repair mirror light decorative compact luminarious with decorative ends caps 9/10 Watt LED with all accessories and including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F in repair Decorative wall mounting light SS finish fixture made up of Polycarbonate with opel glass diffuser suitable for LED/retrofit lamp 15 watts including LED/GLS lamp complete all as specified and directed by Engineer-in-charge .

S&F in repair LED tube light fitting batten type with extruded alluminium body and polycarbonate deffuser all in one single phase 22/20 W with lamp 6500/4000 K complete pre-wired all accessories complete all as specified and directed .

S&F in repair connecting and testing of 30 watt LED building security light luminaries with min 10 KV surge protector die cast alluminium housing LDR sensor for automatic operation complete suitable for and incl bracket 32 mm GI pipe bend to shape incl clamp fastner, bolts, nuts & washers of min 1.2 Mtr incl grouting etc and 3 core 1 sqmm PVC insulated cable from ceiling rose to light fitting complete all as specified and directed .

Supply and fixing in repair of 10/12 Watts LED Bulk head light fitting die cast alluminum body and defused glass cover complete all as specified and directed .

S & F Lamp holder polycarbonate insulated body, with back plate with and incl LED lamp retrofit 3/5 watts complete all as specified and directed .

S & F Lamp holder polycarbonate insulated body, with back plate with and incl LED lamp retrofit 9/10 watts complete all as specified and directed .

M&L for Point wiring with 1100 Volts, grade 1.5 Sqmm. (nominal area) ,PVC insulated but unsheathed multistranded copper conductor single core FRLS cable drawn through and including non metallic medium duty rigid PVC concealed conduit (medium duty) 20mm dia or higher size complete with all accessories such as socket, elbow, junction box, bell mouth, bend, reducer etc and 1.5 sqmm. (nominal area) single core FRLS, PVC insulated 1100 volts, grade multi stranded unsheathed copper conductor cable green colour as earth wire upto common earth and connected to earth dolly including cutting chases for conduits and sinking's for boxes and makin good to walls, floors etc as per existing one complete all as speciied and directed by Engr-in-Charge of following. Note: (i) The wiring to be done as per IE rule and maintain colour code accordingly. (ii) Modular boxes & moduler combined cover plates shall be paid separately as per site under respective items here-in-after. Make of FLRS copper cable of size 1.5/2.5 sqmm.

(a) One light point/ Fan point controlled by one, one way switch

(b) One bell point controlled by one-one way switch through regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

All as per item No. 175.00 above here in but with 2.5 Sqmm. (nominal area) cable for phase & neutral for one 3 Pin 15 amp socket on independent board including one 2.5 sqmm PVC insulated unsheathed multi stranded copper conductor cable FRLS,1100 volts grade as earth continuity conductor upto common earth & connected to earth dolly complete all as specified and directed by Eng.-in-charge.

M&L for Point wiring with 1100 Volts, grade 1.5 Sqmm. (nominal area) ,PVC insulated but unsheathed multistranded copper conductor single core FRLS cable drawn through existing steel / PVC conduit complete with all accessories such as socket, elbow, junction box, bell mouth, bend, reducer etc and 1.5 sqmm. (nominal area) single core FRLS, PVC insulated 1100 volts, grade multi stranded unsheathed copper conductor cable green colour as earth wire upto common earth and connected to earth dolly including cutting chases for conduits and sinking's for boxes and makin good to walls, floors etc as per existing one complete all as speciied and directed by Engr-in-Charge of following. Note: (i) The wiring to be done as per IE rule and maintain colour code accordingly. (ii) Modular boxes & moduler combined cover plates shall be paid separately as per site under respective items here-in-after. Make of FLRS copper cable of size 1.5/2.5 sqmm.

(a) One light point/ fan point controlled by one, one way switch

(b) One bell point controlled by one-one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

(e) One light point controlled by two nos, two way switches.

All as per item No. 177.00 above here in but with 2.5 Sqmm. (nominal area) cable for phase & neutral for one 3 Pin 15 amp socket on independent board including one 2.5 sqmm PVC insulated unsheathed multi stranded copper conductor cable FRLS,1100 volts grade as earth continuity conductor upto common earth & connected to earth dolly complete all as specified and directed by Eng.-in-charge.

Taking down carefully copper aluminum point wiring (light, fan socket and power) complete including switches, ceiling rose, lamp holder and regulator, light fitting etc and removing from site and making good to any disturbed surfaces of walls floors etc. as per existing specification complete all as specified and directed.

Supply and fixing decorative polycarbonate modular white frame for fixing of switches and cover plate suitable for 12 modules 3 row and blanking plate if any required for spare module complete all as specified and directed.

All as per item No 180 here and above but 8 module single or double row as per site requirement complete all as directed by Engr incharge.

All as per item No 180 here and above but 6 module complete all as specified and directed.

All as per item No 180 here and above but 3 module complete all as specified and directed.

All as per item No 180 here and above but 1 or 2 module complete all as specified and directed.

S&F Modular switch 1 way 06 amp single pole complete all as specified and directed.

S&F Modular switch 2 way 06 amp single pole complete all as specified and directed.

S & F modular switch socket combination 16A, 6 Pin of 3 module complete all as specified and directed..

S & F of modular socket outlet 6A-5 pin combined of 02 module complete all as specified and directed.

S & of moduar bell push 6 Amp 1 module complete all as specified and directed.

S & F of modular fan step regulator 120 W-2 module complete all as specified and directed.

S & F calling bell, AC 230 Volt single pole complete all as specified and directed.

Supply and fixing Ceiling rose, three terminal ISI marked surface bakelite suitable for batten fitting complete all as specified.

Taking down submain wiring of any size any type and in any position metalic/non metallic PVC conduit of wooden batten and making good the disturbed surface complete all as specified and directed.

M&L, sub main wiring with two single core PVC insulated unsheathed FRLS multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 6 sqmm size drawn in and including non metallic rigid PVC concealed conduit (ISI marked with valid CML No) not less than 25 mm dia with all fitting & fixing accessories including one run single core PVC insulated unsheathed 6 Sqmm FRLS copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed.

S&F in repair of tamper proof electronic single phase whole currrent energy meter (self powered LCD display) 10 Amp to 60 Amp, 240 volt class 1.0 AC supply including cable connection, proper sealing with lead. The meter shall comply with the latest version of IS-13779 with at least 2 anti tamper LED indications of line load reversal and earth loading indication including electrical connection with existing system and sealing properly in meter box on and incl 3 mm thick bakelite sheet complete all as specified and directed. Make:- Secure/L&T/BEL Note: 1) The meter shall work satisfactory with guaranted accuracy as per limit of IS: 13779. 2) The meter shall be fixed on existing steel boxes on wall complete all as specified and directed. 3) Old unserviceable meter will be deposited to E/M store yard)

Supply and fixing in replacement of Busbar chamber of size 600x315x214 mm or higher size with PVC hinged lid suitable for and mounting arrangement for fixing of MCCB 4 pole, 160 Amps 25 KA (Icu=100%Ics) 415 Volt,50 Hz, duly connected with and incl 04 Nos of copper Busbar 300 Amps fixed on epoxy insulators, Gun metal cable gland of 25 Sqmm 01 No and PVC coupler for sub main wires 04 Nos complete Polycarbonate type (shock proof, rust free, corrosion free, acid and chemical resistant, fire retardant, having high impact, made of halogen and silica free recyclable material), UV resistant, having high grade gasket made of Polyurethane, flame retardant,complete all as directed at site by Engr in charge or his rep complete. Note:- Only MCCB shall be measured and paid for seperately all other items incl connection from MCCB to busbar with suitable size copper wire incl thimble, bottle lugs etc are incl in item rate. Make:- Hensel cat No Mi 9410 or ABB/BCH/Schneider

M&L in repair for Distribution board Vertical type TPN 4 Way double door, suitable for MCCB 63/100 Amps MCCB as incoming and MCBs for outgoing factory made, IS: 13032 marked with valid CM/L No fabricated out of CRCA sheet not less than 1.2 mm thick fitted with DIN channel, neutral and earthing link and bus bar. DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and baked at high temperature, painted in seven tank process. The DBs shall be of IP 43 protection incl taking out old u/s complete all as specified and directed.

M&L in repair for Distribution board SPN 8 Way double door, for mounting MCBs isolator, ELCBs etc factory made, IS: 13032 marked with valid CM/L No fabricated out of CRCA sheet not less than 1.2 mm thick fitted with DIN channel, neutral and earthing link and bus bar complete all as specified and directed.

Supply and fixing of MCCB 100 Amps FP 415 Volts having breaking capacity 16 KA with and incl spreader link kit complete suitable for fixing as incoming in polycarbonate busbar complete all as specified and directed.

S & F , MCB SP 6 to 40 Amp, 240 Volts, 'C' curve having breaking capacity 10 KA, complete all as specified and directed.

S & F , Isolator SPN 40 to 63 Amps, 240 Volts having braking capacity10 KA. complete all as specified and directed.

S&F in replacement Sheet metal enclosure SPN with a two pin and earth plug and socket complete with one single pole MCB 20 Amp 10 KA C series complete all as specrified & directed.

Material and labour for CPRI approved chemical earthing complete with GI pipe electrode 50 mm dia, 2 Mtr long with terminal size 50x6 mm buried directly in ground not less than 2.25 m deep below normal ground level connected with and incl galvanized wire 4 mm earth lead upto DB by means of nuts bolts check nuts GI washers etc duly protected by galvanized iron pipe 15 mm bore (light grade) including PVC accesse well and cover and gel type back fill compound necessary earth work in soft/loose soil complete all as directed by Engr in charge including testing on completion all as specified and directed. incl demolition to existing one complete all as specified and directed. Note: The unit rate includes for protection pipe GI 15 mm dia light grade and GI wire 4 mm dia from top of electrode up to 7.5 meter complete all as specified and directed.

M/s. Kansal Construction Co.

PAWAN KUMAR

M/S SETHI BROTHERS

M/S C S AITHANI

M/s Anil Kumar

AYUSH CONSTRUCTION COMPANY