REPAIRS REPLACEMENT OF INTERNAL WIRING OF SUB STATIONS AND PUMP HOUSES AND ALLIED WORKS UNDER GE UTILITY AMBALA

Amount

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder, regulators, switch socket outlet, bulk head fittings, tube light fittings, calling bell etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and directed.

Material and labour for Point wiring with 2 Run of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit medium grade not less than 20 mm dia with accessories/ casing caping, concealed/surface type on wall/ceiling and including provision of 1.50 Sqmm single core PVC insulated, unsheathed cable FRLS-H, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including sunken pressed steel terminal boxes (modular type, size/modules as required at site) with and including screws, modular cover plate over sunken box for housing the modular switches, socket outlet Supply & fix an regulators etc and making good the disturbed surfaces as per existing for :- One light point/bell/fan point controlled by one switch Note:-1. Modular metal flush/sunken Box, and for modular switch/socket cover plate & sheet are inclusive in the item rate quoted. 2. Switch, socket and fan regulators to be measured and paid separately.

All as per Srl Item No 2.00 here-in-before but One 3 pin socket point 5 Amps on independent board

All as per Srl Item No 2.00 here-in-before but One 3 pin socket point 5 Amps on same board

All as per Srl Item No 2.00 here-in-before but for one socket point 15 Amp with 2.5 sq mm PVC unsheathed FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 2.5 sq mm green colour FRLS-H, 1100 volt grade ISI marked copper wire as earth continuity conductor connected to common earth dolly complete all as specified & directed.

All as per Srl Item No 2.00 here-in-before but for one socket point 15 Amp/AC box with 4 sq mm PVC unsheathed FRLS-H, 1100 volt grade ISI marked, multi stranded copper conductor along with 4 sq mm green colour FRLS-H, 1100 volt grade ISI marked copper wire as earth continuity conductor connected to common earth dolly complete all as specified & directed.

Supply & fix modular switch 6 Amp 1 way 1 module 230 volts complete all as specified & directed.

Supply & fix switch modular 16 Amp 1 way 1 module 230 volts complete all as specified & directed.

Supply & fix socket modular 2/3 pin 5 Amp 2 module 230 volts complete all as specified & directed.

Supply & fix socket modular 2/3 pin 6/16 Amp 2 module 230 volts complete all as specified & directed.

Supply & fix of electronic Fan regulator modular 100 watt 2 module complete all as specified & directed.

Supply & fix modular bell push 6 Amp 1 way 1 module 230 volts complete all as specified & directed.

Supply & fix Calling bell ding dong type SP AC supply, 230 volts complete all as specified & directed.

Supply and fix ceiling rose surface type 2/3 terminal complete all as specified and directed.

Supply and fix lamp holder, insulated body, with back plate for angular batten fittings complete all as specified and directed.

Supply & fix switch 6 Amp 1 way 230 volts complete all as specified & directed.

Supply & fix switch 16 Amp 1 way 230 volts complete all as specified & directed.

Supply & fix socket outlet 2/3 pin 5 Amp 230 volts complete all as specified & directed.

Supply & fix socket outlet 2/3 pin 6/16 Amp 230 volts complete all as specified & directed.

Supply & fix of electronic Fan regulator 100 watt complete all as specified & directed.

Supply & fix bell push 6 Amp 1 way 230 volts complete all as specified & directed.

Supply & fix LED lamp 9 watt threaded/pin end, warm/cool lamp type as per site requirement suitable for fixing on existing batten/angular holders complete all as specified and directed.

Supply & fix LED lamp 12 watt threaded/pin end, warm/cool lamp type as per site requirement suitable for fixing on existing batten/angular holders complete all as specified and directed.

Supply and fixing Lumiline Plus LED batten tube light fitting 20 watt, 4 feet long, wall mounted box type, opal diffuser, high efficient aluminum housing body, high efficient, AC 220-240 volts, 50 Hz and including 20 W LED tube rod (luminaries) environment friendly, high efficient, T8 with aluminium extrusion heat sink connecting with copper conductor flexible cable from ceiling rose to connector of the light including taking down existing complete all as specified and directed. Make Havells cat part No LUMILINE+BS20WLED865SPCSS or equivalent in Bajaj/Philips/Wipro

Supply and fixing Lumiline Plus LED batten fitting 10-12 watt, 2 feet, aluminium body including driver, tube rod cool/warm type industrial model complete connecting with copper conductor flexible cable from ceiling rose to connector of the light including taking down existing complete all as specified and directed. Make Havells cat part No LUMILINE+BS10WLED865SPCSS or equivalent in Bajaj/Philips/Wipro

Supply and fixing LED surface mounted bulk head luminaries 8-10 W with min 800 lumen, industrial model, IP 65, Aluminum housing, surge protection including driver & LED etc complete with all accessories connecting with copper conductor flexible cable from ceiling rose to connector of the light including taking down existing complete all as specified and directed. Make Havells cat part No HEXAFT10WLED857SSYMBOPC or equivalent in Bajaj/Philips//Wipro

Supply and fixing decorative wall light, stainless steel , rust free fixture with white glass diffuser suitable for 7.5/9 watt LED filament lamp E27 base , model No FLORETTE WL recess mounting LED 15/18 Watt circular down lighter/Spot LS E27 GLD, 240 volt, 50HZ, AC supply complete with all accessories internally pre wired including connecting with 3 core flexible copper conductor from ceiling rose to connector of the light including taking down existing complete all as specified and directed. Make Havells cat part No LHFOAID1TZ1I040 or equivalent in Bajaj/Philips/Wipro

Supply & fixing of LED street light fitting 45 watts made up of pressure die cast aluminium housing with high efficiency LEDs as lighting source and lens embedded PC cover/ toughened glass having TOP Opening seperate driver compartment with IP 66 protection and impact resistance of IK07 consisting of suitable number of LEDs with sealed toughened glass cover, 5700K, LED efficiency >110 lm/Watt and system efficiency 110 lm/W , 240 Volts AC, 50 Hz, CRI>70% operating voltage range 140 V-270 V, Power factor> 0.95,mains current 0.270A, working temperature range -10ºC to 50ºC,built in surge protection of more than 10 kV, better optics for uniform distrubution with multiple LEDs not less than 2 watt each and having optical grade polycarbonate lens with all accessories , suitable for side entry, pole mounting with bracket arm OD 40 mm, recommended mounting height with suitable inground reinforcement is 8 mtrs, Confirm the safety test as per IS 15885 part-2 from auth labs : LM79 & LM 80 including electric connection including taking down existing complete all as specified and directed. Make Havells cat part No ENDURASUNDOWNSL45WLED765PASYBOPC or equivalent in Bajaj/Philips/Crompton

Supply & fixing of LED Flood light Luminaries 150 Watts consisting of suitable number of LEDs and mounted on MCPCB high pressure die cast aluminium housing with sealed toughened glass cover, IP 66 protection suitable for mast light mounting, 5700K, LED efficiency >130 lm/Watt with PC lens and system efficiency 110 lm/W , 240 Volts AC, 50 Hz, CRI>70% operating voltage range 160 V-270 V, Power factor> 0.95, working temperature range -10ºC to 50ºC,built in surge protection of more than 10 kV , Confirm the tests from auth labs : LM79 & LM 80, incl proper fixing and testing of flood lights on 9/11 mtr long steel tubular pole and provide facility of power supply shall be provide as suitable for maint work of light fittings incl make proper connection of new and existing light fittings complete with cutting , welding , drilling holes, nut bolts, washer including connecting with flexible copper conductor to connector of the light with necessary fixing arrangements including taking down existing complete all as specified and directed. Make Havells cat part No JETAIRISFL150WLED757ARNBLTG or equivalent in Bajaj/Philips/Crompton

Supply and fixing in replacement of ultra slim LED flat panel 2' x 2' size surface/ recess mounted (grid/ gypsum type) 36-40 watt , warm/cool white with provision of PVC flexible copper conductor cable to light fitting including taking down existing complete all as specified and directed. Make Havells /Bajaj/Philips/Wipro

Supply & fix UFO LED Bollard 8-10 W, IP-65 luminaire made of pressure die-cast aluminium housing, 240 volt, 50HZ, AC supply , complete with all accessories internally pre wired including connecting with flexible copper conductor from Electric Supply Source to connector of the light including PCC 1:3:6 of size 400x400x400 mm including taking down existing complete all as specified and directed. Make Havells cat part No UFOBLS10WLED830PSYMTOPCN or equivalent in Bajaj/Philips/ Wipro

Supply & fix LED post top luminaire 30-35W IP-65 made of pressure die-cast aluminium housing & clear glass 240 volt, 50HZ, AC supply complete with all accessories internally pre wired including connecting with fitting and including fitting & provision of 3 core PVC flexible copper conductor from Electric Supply Source to connector of the light including taking down existing complete all as specified and directed. Make Havells cat part No CORALPT35WLED757PSYMTOPC or equivalent in Bajaj/Philips/ Wipro

Supply & fix single pole and neutral enclosure with a two pin and earth plug and socket 20 Amp complete with and including one single pole MCB. 20 Amp including removing old unserviceable enclosure complete all as specified and directed. Make Havells/Indoasian/L&T/Legrand/Siemens

Supply and fix sheet metal MCB DBs 4 way with 200 Amps rated bus bar single pole and neutral, IP-43, double door fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth disturbed surface after removing old unserviceable MCB DB complete all as specified and directed.

Supply and fix sheet metal MCB DBs 8 way with 200 Amps rated bus bar single pole and neutral IP-43, doubel door fixed on wall duly grouted in solid block wall or on wooden board, including copper lugs/thimbles duly crimped for connection, including making smooth disturbed surface after removing old unserviceable MCB DB complete all as specified and directed.

Supply and fix sheet metal enclosure Vertical triple pole & neutral(VTPN) with MCCB TPN 125 Amp for 415 volts 4 way with 200 Amp rated bus bar flush /surface mounting double door duly grouted in solid block wall or on wooden board in and including lugs/thimbles duly crimped for connection including making smooth the disturbed surface after removing old unserviceable VTPN complete all as specified and directed. Make :- Havells/Indoasian/L&T/ Legrand/Siemens

Supply and fix MCB SP 6-32 Amps, 240 volt,10 KA 'C' curve including taking down unserviceable MCB complete all as specified and directed.

Supply and fix MCB SPN 32/40 Amps, 240 volt,10 KA 'C' curve including taking down unserviceable MCB complete all as specified and directed.

Supply and fix sub main wiring with two run of 6 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volt grade ISI marked multi stranded copper conductor with one run of 6 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked multi stranded copper conductor connected to common earth dolly including capping & casing or concealed on wall/ceiling in PVC conduit medium grade not less than 25 mm dia ISI marked of adequate size for housing the wires including taking out of old u/s sub main wiring of any size complete all as specified and directed. Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB (ii) For the purpose of payment two runs of 6 sqmm conductors and one run of 6 sqmm conductor with conduit shall be measured as one length of one RM.

Supply and fix sub main wiring with two run of 4 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volt grade ISI marked multi stranded copper conductor with one run of 4 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked multi stranded copper conductor connected to common earth dolly including capping & casing or concealed on wall/ceiling in PVC conduit medium grade not less than 25 mm dia ISI marked of adequate size for housing the wires including taking out of old u/s sub main wiring of any size complete all as specified and directed. Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB (ii) For the purpose of payment two runs of 4 sqmm conductors and one run of 4 sqmm conductor with conduit shall be measured as one length of one RM.

Supply, laying, fixing or passing through pipe 1100 volts grade heavy duty 2 core, 6 sq mm cable with PVC insulated, multi stranded aluminium conductor served with an inner sheathing of PVC tape and overall PVC sheathed in service connection, including disconnecting and taking down old U/S existing cable complete all as specified and directed.

Supply, laying, fixing or passing through pipe 1100 volts grade heavy duty 2 core, 10 sq mm cable with PVC insulated, multi stranded aluminium conductor served with an inner sheathing of PVC tape and overall PVC sheathed in service connection, including disconnecting and taking down old U/S existing cable complete all as specified and directed.

Disconnecting & taking out defective underground cable from trenches, pole, pipe, floor, wall etc and locate the fault, rectify the defect and relaying the XLPE cable underground PVC insulated and overall sheathed aluminum conductor heavy duty 1100 volts including connecting and testing for any size complete all as specified and directed. Note:- Cushioning, bricks and joint shall be measured & paid for separately.

Supply and laying, connecting and testing XPLE underground cable insulated, and overall sheathed with aluminium conductor heavy duty 1100 volts grade 10 sqmm 4.0 core including Al thimbles laid in trenches/on pole/road crossing or passing through existing/new pipe under road crossing clamping on wall etc. including disconnecting and taking down old U/S existing cable complete all as specified and directed. Note : (i) Earth work, sand, bricks removing, returning filling will be paid seperately. (ii) Cost of laying electrical cable through new/existing pipe under road, buildings, railway tracks, highways are incl in the quoted rates (iii) All equiments, machinery or tool if required for laying electrical cable through new/existing pipes are provided by the contractor without any extra cost.

All as per Srl Item No. 44.00 here in before but for 4 core 16 Sqmm

All as per Srl Item No. 44.00 here in before but for 3.5 core 25 Sqmm

All as per Srl Item No. 44.00 here in before but for 3.5 core 35 Sqmm

Supply & fix light grade GI Tubing of size 40 mm dia for cable protection and fixed with clamp to pole and wall with nut bolts, including disconnecting and taking down existing pipe and removing complete all as specified and directed.

Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique or manual boring and necessary machine including HDPE pipe of 50mm to 150 mm dia suitable for 0.4 mpa working pressure complete all as specified and directed.

Excavation in trenches not exceeding 1.5 meter wide and not exceeding 1.5 meter deep and getting out in any type of soil complete all as specified and directed.

Returning, Filling in excavated soils including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Material and labour for dry sand cushioning to cable 8 cm before laying cable in trenches and 15 cm after laying the cable and compacting, complete all as specified and directed.

Supply and laying bricks, common burnt clay, sub class "B', old size, laid in vertical direction to cable as cable protection complete all as specified and directed.

Material and labour for PCC 1:3:6 (nominal mix) type C-2 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete complete all as specified and directed.

Material and labour for earthing complete with galvanised earth plate electrode 600mm x 600mmx 6.00mm thick surrounded by charcoal and salt, buried directly in ground vertically in a pit of depth not less than 2.25m below ground level with top edge of the earth plate not less than 1.5m below normal ground level, connected to 25x4 mm GI strip earth lead by means of bolts, nuts, checks nut and washers made out of galvanized iron or steel, earth wire protected by galvanized steel pipe 40mm bore (light grade) and connected to main switch or main control board all as shown in electrical plate No.3 of SSR Part-I & including necessary excavation and earth work. The rate also include charcoal & salt in alternate layers, 20mm bore GI pipe (medium grade) for watering and 40mm bore GI protection pipe, funnel, wire mesh, cast iron cover and frame etc, complete, all as specified or indicated and as directed including testing on completion including dismantling and taking down old earthing complete all as specified and directed. Note : The quoted rate shall include the cost of earth work, GI pipe for watering, GI protection pipe, funnel, wire mesh, RCC cover, RCC cover shall be 50mm thick in PCC 1:2:4 type B-1 using 8mm TMT bars @10cm c/c both way as approved.

Material & labour for earthing complete with galvanized steel earth electrode plate of size 60x60x6mm thick buried directly in ground/earth pit not less than 2.25 mtr deep below normal ground level and top edge of earth electrode not less than 1.5 mtr below normal ground level and connected with GI earth wire of size 4 mm by means of nut, bolts, washers etc to eqpt/machinery all as shown in electric plate No 3 of SSR Pt I including PCC (1:3:6) pit, pit cover 50mm thick RCC 1:2:4 type B-1 using 8mm tor steel bars @10cm C/C both ways, 20 mm bore medium grade GI protection pipe, watering pipe 20mm bore medium grade, funnel, wire mesh, also including earth work, common salt, charcoal dust including dismantling and taking down complete all as specified and directed.

Supply and fix LED 22 watt integrated batten with inbuilt lithium ion battery with minimum 4 hour back up including taking down of unservicable light fitting complete all as specified and directed.

Supply and fix LED lamp Invertor technology 9 watt with 4 hour power back up with efficiency more than 100 lumen per watt,Lithium ion battery including taking down of unservicable lamp complete all as specified and directed.

Refixing only existing serviceable LED light fittings of any description after cleaning complete all as specified and directed.

Taking down carefully unserviceable exhaust fans/ceiling fans of any size from its position, dismanteling blades, opening the fan motor, removing the burnt grease, applying new bearing grease, removing of defective parts such as ball bearing, bush bearing, burnt winding, shaft, split pin, condensor, condensor holder, shackle, reassembling after replacement of defective parts including replacements of 3 core, 0.75sqmm (24/0.2mm) flexible copper cable from ceiling rose to connector, hanging on its position properly complete all as specified and directed. Note:- Defective parts like ball bearing, bush bearing and motor rewinding, shaft, condensor, rubber shackle will be measured and paid separately.

Supply and fix in replacement of ball /bush bearing suitable for exhaust fan of same size as that of existing defective one (ISI Marked) complete all as specified and directed. Make: SKF/TATA/Universal/polar

Supply and fix in replacement of condenser capacity 4/3.15/2 MFD complete all as specified and directed. Make: Usha/Universal/ Keltran

Cleaning and preparing the surfaces of exhaust fans/ceiling fan any size, removing the grease, carbon dust over the fans and painting with one coat of synthetic enamel paint of approved colour with brush painting and writing MES number on the fan complete all as specified and directed.

Material & labour for rewinding exhaust fans/ceiling fans with super enamelled bare copper conductor with the same size and number of turns as that of the old one, insulating, varnishing and pre heating for exhaust fan 280 to 450 mm sweep and ceiling fans 1200/1400 mm sweep complete all as specified and directed.

Supply and fix in replacement of blade suitable for exhaust fan 280/300/450mm, size as that of existing defective one complete all as specified and directed. (ISI Marked)

Supply and fix in replacement of blade suitable for ceiling fans 1200/1400mm, size as that of existing defective one complete all as specified and directed. (ISI Marked)

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed.

Supply and fixing in replacement of ceiling fan BLDC type with remote control complete with all acessories 230 V, 50Hz, 1200 mm sweep , required at site etc, colour Beige-Brown / Pearl Ivory-Gold/white complete all as specified and directed.

Supply and fixing in replacement wall mounting fans complete with all acessories 230 V, 400 mm sweep , 60 CFM air flow, 90 degree swing and 1400 RPM Motor speed as required at site etc complete all as specified and directed.

Supply and fixing in replacement of exhaust fan AC single phase 230/240, 50 HZ Volt of size 450/300 mm sweep metal body power flow operating with louvers shutter complete grouting the ragged bolt in wall fixing the frame and exhaust fan fix including louver shutter with frame on the exhaust side and connecting with PVC insulator 3 core 23/0.0076 copper wire rubber insulated from ceiling rose to exhaust fan motor complete all as specified and directed.

Taking down/dismantling of defective/rusted storage type hot water Geyser of 50/35/25 litre capacity from different locations by disconnecting inlet/outlet connections and taking out unserviceable parts by unscrewing bolts and nuts, descaling/cleaning inner shell, servicing etc. checking defects, re-assembling and re-installing the Geyser in position, connecting and testing complete all as specified and directed.

Supply & fix PVC flexible pipes 15mm dia (heavy duty) both end socketed with washer 450/600 mm long for hot/cold water (ISI marked) complete all as specified and directed.

Supply and fix in replacement of stop valve fancy type cast copper alloy screwed down high pressure with crutch or butter fly handle, chromium plated screwed both ends of size 15 mm bore, for geyser connection complete all as specified and directed.

Supply & fix in replacement of thermal Auto cut of range 0-90 degree centigrade (ISI marked) complete all as specified and directed.

Supply & fix in replacement of gyser heating element 1.5/2 KW (ISI marked) round type/thread/triangle base type with the provision of thermal cut out complete all as specified and directed.

Supply & fix in replacement of inner tank 6/9 holes suitable for Gyser 25/35/50 litres capacity (Apparatus assembly) made copper duly prewired. Make: Usha/Havells/Lexus/Crompton

Supply & fix in replacement of Gyser assembly 6/9 holes suitable for 25/35/50 litres gyser capacity (ISI Marked) complete all as specified and directed.

Supply & fixing in replacement of Electric storage water heater of capacity 25 Ltrs of five star rating, AC 230 volts with PVC connection piipe 15 mm dia heavy duty approx length 450/600mm long -02 Nos, Hole fastener Nut & Bolts made of iron approx length 6 cm long -04 Nos, union socket 15mm dia -02 Nos, Tee 15 mm dia -01 Nos, complete all as specified and directed .

Supply & laying in replacement of GI tubing medium grade with all fittings and fixed to walls/ceiling/ floor or laid in trenches of 15 mm bore size for cold/hot water pipe line complete all as specified and directed.

Supply & fixing in replacement of Bib taps cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe or brass ferrule and fixed fancy type, chromium plated of size 15 mm dia complete all as specified and directed

Cutting & screwing existing steel tubing of size 20 mm dia for alterations or lengtheing screw on pipe to form connector and done in position with out taking down complete all as specified and directed.

Supply only of PVC self adhesive insulation tape of size .125mm x 25mm x 25 mtr long ISI marked complete all as specified and directed.

Supply and installing, testing & commissioning in replacement of factory fabricated outdoor type feeder pillar board of size 700X600X500 mm , outer shell made out of 3.15 mm thick CRCA sheet and inner shell made out of 2 mm thick CRCA sheet and MS angle section 50x50x6 mm mounted on PCC 1:2:4 type B-1 platform 60 cm above and 45 cm below the ground level, frame factory fabricated with front openable double door system and cable alloy (Each door hinged with body at 3 places with body and hinges should be welded with body and door) lockable/open able with arrangement of pad locking on door 01 no of pad lock of three keys shall be used to make the outer shell completely vermin proof suitable for 3 phase 4 wire 415 Volt, 50 Hz, tested at factory approved from CPRI factory fabricated having modern fabrication and testing process followed by powder coated painting after 7-tank pre treatement control & power wiring with suitable size of copper conductor along with suitable gasket to make it dust/vermin proof and general construction confirming to IS:61439/2011 Part-1 and part -2 type test certificate with not less than IP-56 and breaking capacity 65 KA comprising of the following :- (a) MCCB 125 Amps TPN, 25 KA -01 No (b) Aluminium busbar of capacity 200 Amps with colour coated heat shrinkable sleeve and suitable hole for out going connection - Set of four. (c) Misc items like screws, cable tie, copper cable 1.5/2.5 Sqmm, cable lugs, sleeves, glands etc complete are included in quoted rates.

Supply & fix in replacement of metal flush mounting box with cover plate 1-3 module for day to day complaint including all accessories and making good the disturbed surfaces as per existing complete all as specified and directed.

Supply & fix in replacement of metal flush mounting box with cover plate 4-8 module for day to day complaint including all accessories and making good the disturbed surfaces as per existing complete all as specified & directed.

Supply & fix in replacement of metal flush mounting box with bakalit sheet of size 4" x 4" to 12" x 18" for day to day complaint including all accessories and making good the disturbed surfaces as per existing complete all as specified & directed.

Supply & fix modular switch 6 Amp 1 way 1 module 230 volts for day to day complaint including disconnecting and taking down existing old U/S complete all as specified & directed.

Supply & fix switch modular 16 Amp 1 way 1 module 230 volts for day to day complaint including disconnecting and taking down existing old U/S complete all as specified & directed.

Supply & fix socket modular 2/3 pin 5 Amp 2 module 230 volts for day to day complaint including disconnecting and taking down existing old U/S complete all as specified & directed.

Supply & fix socket modular 2/3 pin 6/16 Amp 2 module 230 volts for day to day complaint including disconnecting and taking down existing old U/S complete all as specified & directed.

Supply & fix switch 6 Amp 1 way 230 volts for day to day complaint including disconnecting and taking down existing old U/S complete all as specified & directed.

Supply & fix switch 16 Amp 1 way 230 volts for day to day complaint including disconnecting and taking down existing old U/S complete all as specified & directed.

Supply & fix socket 2/3 pin 5 Amp 230 volts for day to day complaint including disconnecting and taking down existing old U/S complete all as specified & directed.

Supply & fix socket 2/3 pin 6/16 Amp 230 volts for day to day complaint including disconnecting and taking down existing old U/S complete all as specified & directed.

Supply & fix pulg top 15 Amp including PVC gang box and fixing screw ISI marked including disconnecting and taking down existing old U/S complete all as specified & directed.

Supply & fix plug top 5 Amp including PVC gang box and fixing screw ISI marked including disconnecting and taking down existing old U/S complete all as specified & directed.

Material & Labour in replacement of 1.5 sq mm single core multi stranded copper conductor PVC (FRLS) insulated unsheathed cable confirming to IS-694,1100 Volts grade ISI Marked all as specified and directed.

Material & Labour in replacement of 2.5 sq mm single core multi stranded copper conductor PVC (FRLS) insulated unsheathed cable confirming to IS-694,1100 Volts grade ISI Marked complete all as specified and directed.

Supply and fixing in replacement MCCB TPN 250 Amps, 415 Volts, 25 KA,4 pole , Ics=100% Icu, overload adjustable short circuit adjustable type incl connection complete all as specified and directed.

Supply and fixing in replacement MCCB TPN 200 Amps, 415 Volts, 25 KA,4 pole , Ics=100% Icu, overload adjustable short circuit adjustable type incl connection complete all as specified and directed.

Supply and fixing in replacement MCCB TPN 125 Amps, 415 Volts, 16 KA,4 pole , Ics=100% Icu, overload adjustable short circuit adjustable type incl connection complete all as specified and directed.

Supply and fixing in replacement MCCB TPN 100 Amps, 415 Volts, 16 KA, 4 pole , Ics=100% Icu, overload adjustable short circuit adjustable type incl connection complete all as specified and directed.

Receiving / recording complaints for MES installations and various Sub Stations under GE(Utility) Ambala cantt area to internal electric distribution network, to comprehensive maintenance by attendng daily complaints including Sunday and other holidays for round the clock and making the same serviceable in all respects alongwith replacement of any accesssories of internal wiring, adhesive tape and other connected minor accessories shall also include to visual inspection of DBs, MCBs, service wire, tube light, bulb, switch, socket, ceiling rose, lamp holder, street lights and allied works are included in quoted rates complete all as directed to the entire satisfacation of Engineer-in-charge. Note :- (i) Any complaint left unattended will be communicated to the JE in-charge /AGE E/M with reason. Penalty of Rs. 200/- per day will be levied from the contractor if the complaint is not attended and completed within 24 hours. (ii) Material required for completing the job shall be measured and paid for separately under relevant items of BOQ. (iii) Contractor shall provide all type of T&P of LT street lights network, bamboo ladder with safety gloves for attending the external electric complaints. (iv) Contractor shall provide the complaint register 200 pages – 3 No, complaint book with 100 slips- 5 No. Booklets serially numbered in triplicate. (v) Contractor will provide adequate/ sufficient No of manpower round the clock including Sunday & holidays to receive and attend Complaints.

Dismantling and taking down security light, street light, hanger light, flood light of any type at any height fittings such as HPSV/HPMV/LED light of 48 Watt/ 60 watt /150 watt/ of any make etc. AC 230 volts any wattage from pole/wall roof top/hanger roof including washing/cleaning of perplex cover inspection for location of fault and replacing of defective speare/parts required for smooth functioning, tighting of electric connection complete and assembling and reconnecting all as per site requirment complete all as specified and directed. Note: Defective spare/ part of relevant light fitting shall be measured and paid separately under relevant item as supply only.

Supply only LED electronic driver/adaptor/SPD for 40-60 watt LED security light fitting existing make complete all as specified and directed.

Supply only LED electronic driver/adaptor/SPD for 60-150 watt LED flood light fitting existing make complete all as specified and directed.

Supply and fixing in replacement of PCBA (printed circuit board assembly) with thermal pad and lens for LED street light fitting existing capacity/make complete all as specified and directed.

Material and labour for spraying herbicide (Round up) on area to remove unwanted vegitation/grass at various locations complete all as specified and directed.

Trimming of Tree branches falls into OH lines of HT/LT & minimum clearance of 3 Mtr from branches ,proper shutdown will be taken and maintained in the register complete all as specified and directed.

Note:- Amount of credit of Rs. 72015.50 for retrieved materials is mentioned in Schedule of Credit of tender documents in pdf form which will be deducted offline while acceptance of tender.

M/s badrinath Traders (BID ID -3342986)

AMBALA ENGINEERING CO (BID ID -3343371)

R N Enterprises (BID ID -3337048)

The Rahul Vig (BID ID -3344681)