Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹37.4 LAccepted-AOC | L1 | Accepted-AOC Lowest bidder | |
| 2 | L2₹40.0 L+₹2.6 L (6.90%)Rejected-AOC FLAT NO 4 C GH 39 MANSA DEVI COMPLEX SECTOR 05 PANCHKULA 134 109 HRY | PANCHKULA | PANCHKULA | HARYANA | 134109 | L2 | Rejected-AOC Other than lowest bidder | |
| 3 | Rejected-Technical 96 SECTOR 16 A CHANDIGARH 160015 | CHANDIGARH | CHANDIGARH | 160015 | - | Rejected-Technical Not enlisted in category b i | |
| 4 | Rejected-Technical | - | Rejected-Technical One class below and not enlisted in category b i |
Tender Value
Refer Docs
Closing Date
13 Jun 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
CWE(AF) Chandigarh
HQ CWE(AF) Chandigarh PIN-160003
ADDITION/ALTERATION TO BUILDING NO P-9 AT AF STATION HIGHGROUNDS UNDER AGE (I) HIGHGROUNDS
2022_MES_524021_1
CWE(AF)/CHD/T-06/2022-2023
Open Tender
Civil Works
Item Rate
180 days
Chandigarh
As per NIT
8 documents required · 8 mandatory
₹500
AGE(I) (AF) Highgrounds
Exempted
30 Aug 2022
13 May 2022
20 Jun 2022
13 May 2022
13 Jun 2022
30 May 2022
60 days
Amount
BUILDING WORK
Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specially provided for including removal of debris out of defence land complete all as specified and directed
Demolition of brick masonry work built in cement mortar including all quoins, arches, pillars, staging etc. and removal of rubbish outside MOD land, complete all as specified and directed.
Taking down cement plaster on brick or stone walls or concrete surfaces, etc, any description including raking out joints, hacking for key, scrubbing down with water, etc and removal of rubbish outside MoD land, complete all as specified and directed. Note: The rate quoted by contractor shall be deemed to be inclusive of cost of necessary scaffolding etc.
Material and labour for plain cement concrete 1:4:8 type D-2 using 40 mm graded crushed stone aggregate as in foundation filling and mass concrete, complete all as specified and directed.
Material and labour for brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in CM 1:6, using old size bricks, complete all as specified and directed
Material and labour for brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in CM 1:6, using old size bricks, except bricks complete all as specified and directed. Note: Old bricks retrived from item No 2 here-in-before shall be used.
Material and labour for brickwork in half brick thick wall using subclass 'B' old size bricks, straight or curved on plan exc 6 m mean radius, built in cement mortar (1:4), complete all as specified and directed.
Material and labour for rendering 15mm thick in cement mortar (1:6), on brick/concrete surfaces of walls, finished even and smooth without using extra cement, complete all as specified and directed. Note: The rate quoted by contractor shall be deemed to be inclusive of cost of necessary scaffolding.
Material and labour for rendering 10 mm thick in cement mortar (1:3), on concrete surfaces (such as top & sides of chajjas, beams, balcony, ceiling etc) , finished even and smooth without using extra cement, complete all as specified and directed. Note :- The rates quoted by the contractor shall be deemed to be inclusive of the cost of scaffolding.
Material and labour for preparation of newly plastered surfaces of walls and applying two coats of 1st quality oil bound distemper (oil emulsion) over and including a coat of primer, complete all as specified and directed.
Material and labour for preparation of new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed.
Material & Labour for complete removal of existing treatment and applying two or more coats of 100% Premium acrylic emulsion paint having Volatile Organic Compounds less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistant, dirt resistant exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm of surfaces, complete all as specified and directed. Note: Weather proof exterior emulsion paint and primer shall be of same manufacturer.
Material and labour for preparation of old wooden surfaces over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and directed.
Material and labour for preparation of old steel or iron surfaces over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and directed.
Material and labour for RCC M-25 (Design mix) using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases of columns, etc; basement slabs, under reamed piles and mass concrete, complete all as specified and directed.
Material and labour for RCC M-25 (Design mix) using 20 mm graded aggregate as in Columns, pillars, piers, posts and struts complete all as specified and directed.
Material and labour for RCC M-25 (Design mix) using 20 mm graded aggregates as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.
Material and labour for RCC M-25 (Design mix) using 20 mm graded aggregated as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.
Material and labour for TMT steel bars, 10 mm dia and over , cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, complete all as specified and as directed.
Material and Labour for mild steel TMT bars 6 mm dia and over upto 10 mm dia as in stirrups, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified.
Material and labour for Formwork to concrete foundations, footings, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work, vertical or to batter, flat rough finished concrete surfaces complete all as specified and directed.
Material and Labour for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc, also splays between floors and beams, etc for rough finish flat surface, complete all as specified and as directed.
Material and labour for Formwork to sides of pillars, posts, struts, piers, columns and stanchions etc., flat rough finished concrete surfaces, complete all as specified and directed.
Material and Labour for PCC (1:2:4) type B-0, using 12.5 mm graded crushed stone aggregates, as in bed block, coping, including weathering, slightly rounded or chamfered angle and throating, including necessary form work, complete all as specified and directed.
Material and labour for mild steel screw bolts (machine made) exc. 22.5 cm and n.exc 30 cm long and dia of neck 16 to 20 mm with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut complete all as specified and directed.
Material and labour for 40 mm thick plain cement concrete (1:2:4) type B-0 using 12.5 mm graded crushed stone aggregates as in floor, finished the surface even & rough to receive the bedding mortar, complete all as specified and directed.
Material and labour for first quality Non Skid joint free ceramic coloured tiles 7 to 8 mm thick, (square/rectangular), area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, as in floors etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment or coloured cement to match the shade of tiles, over and including 15 mm thick screed bed/bedding layer in CM (1:6), complete all as specified and directed.
Material and labour for First quality, glazed jointed ceramic coloured tiles, 6-7mm thick, of size 450 mm x 300mm on vertical surface such as in skirting, dados, risers to steps, etc., set and jointed in neat cement slurry @ 3Kg/Sqm, and including pointing in white cement mixed with pigment or coloured cement to match the shade of tiles, complete all as specified and directed.
Material and labour for 20mm thick Granite (of any type) work, machine cut, (table rubbed and polished) fine grained 'Zed' black/red as on cooking platforms, window cills, steps and like, set in neat grey cement slurry @3Kg/Sqm, laid over and including 15 mm thick bedding layer in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including cutting , grinding & polishing, complete all as specified and directed.
Material and labour for Machine cut Kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and Screed bed or bedding layer of 20 mm thick in CM 1:4 for laying floor finish complete all as specified and directed.
Material & Labour for machine cut Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid and jointed with neat cement slurry, over and including 10mm thick rendering of Cement Mortar (1:4) including pointing in white cement with pigment to match the shade of stone slabs, complete all as specified and directed.
Material and labour for PCC 1:2:4, Type B-2 using 40 mm graded stone aggregates as in surface channel/ drains inside the manholes and the like including rounding to any radius, weathering, slightly rounded or chamfered angles and throating as directed including provision of necessary form work, complete all as specified.
Material and labour for precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregates in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling), corbels, brackets, etc (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc and setting in mortar 1:4 complete with joints to match, complete all as specified and directed.
Supply and of fixing roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc with rolled mild steel FE-290 Gde E-165, complete all as specified and directed.
Supply and Fixing of Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick, of any colour (as approved by GE), having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.
Supply and fixing of rolled mild steel section conforming Fe-410-W (Gde-E-250) quality-B in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachement complete all as specified and directed.
Material and labour for applying two coats of synthetic enamel paint over and including a coat of red oxide primer on new steel surfaces over 10 cm width or girth, including preparation of new steel surface, complete all as specified and directed.
Supply and fixing 600 mm x 600 mm x16 mm mineral fibre ceiling tiles, seamless, of type Classic Lite RH-99, fine texture, of 'Armstrong,' fixed on exposed grid system, including provision of anodised aluminium snap grid frame work for false ceiling and hangers 6 mm dia GI (upto 1200 mm length) with level adjusting mechanism, fixed to roof slabs by means of ceilling cleats made out of GI flat 40 mm x 3 mm, 60 mm long and expansion hold fasteners 12.5 mm dia 40mm long complete all as specified and directed.
Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed.
Supply and fixing 12 mm thick prelaminated particle board, interior grade, prelaminated both sides with decorative choice lamination and fixed with screws to aluminium/timber frame work, complete all as specified and directed.
Supply and fixing sheet glass 5.50 mm thick ordinary quality and glazing with oil putty in squares exc 0.5 sqm in each pane complete all as specified and directed
Supply and Fixing Door closer hydraulically regulated, designation No. 3, aluminium (die cast) body, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.
Supply and fixing Anodised Aluminium door shutter, powder coated with minimum thickness of powder coating 50 micron, aluminium section weighing 0.55 KG / RM including necessary Joining Cleats, Glazing Clips, Rubber Packing, Rubber Neoprene Packing, Screws, Anodised Aluminium Snap Beading, Anodised Aluminium Fittings in each shutter such as Handles, 200 mm Long [2 Nos], 100 mm long vertical 4 lever mortice door lock etc complete all as specified and as directed.
Material and Labour for cutting out concrete blocks, slabs, brick work or stone mansonry in alternate course, forming toothing for and bonding new work in cement mortar into old work including new material entering old wall and set in CM 1:6 and/or using PCC 1:2:4 as required, complete all as specified and directed.
Material and labour for cutting openings, through brick walls built in cement mortar for door, window and other openings or enlarging existing openings, converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc., to store and debris outside MOD land, complete all as specified and directed
Material and Labour for forming jambs, etc. to openings, including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, in cement mortar 1:4, complete all as specified and directed.
Cutting chases, pinning in brick walls , making good to facings where required and pointing in cement mortor 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20 cm girth complete all as specified and directed.
Material and labour for making good under cills or over arches, lintels and bressummers in cement mortar 1:4, including all pinning when necessary, , complete all as specified and directed.
Material and labour for mild steel as in framed work of doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing similar work conforming to Fe-410 W (Grade E-250) quality A, complete all as specified and directed.
Material and Labour for collapsible steel gates, top hung, consisting for channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified in Clause 10.24 of SSR Part I and conforming to IS No 10521-1983 and as directed.
Material and Labour for 1mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc as required, complete all as specified and directed.
Excavation over areas not exceeding 1.5 m deep and getting out in soft/loose soil complete all as specified and directed.
AIR CONDITIONING AND REFRIGERATION WORK
Supply installation, testing and commissioning, High wall split type AC unit of capacity 2 TR, with copper piping and condenser, dual inverter, with minimum 5 star rating, electric driven, single phase, indoor and outdoor unit, with cordless remote control and with in-built air ionizer and plasma filter for better indoor air quality, necessary suction and discharge copper pipelines from inner units duly insulated, including welding/ brazing to make leak proof, 15 mm bore PVC pipe of superior quality for drainage of condensed water, including cutting chases for refrigeration piping, connection cable, drain pipe etc in brick wall, necessory brackets/suitable stand for mounting outdoor /indooor units as per manufacturer's instructions and providing electrical connections and electric cable from inner to outer unit complete all as specified and directed. Make- Hitachi, Voltas, Blue star, Carrier Deccan.
Supply and fixing Voltage stabilizer for automatic operation, single phase naturally air cooled wall mounted digital display type & designed for input variation between 175 V to 250 V with output voltage stabilized at 225 V with accuracy of ± 9% and of capacity 5 KVA Make- Sinetrac Model no WMD5000U3T or its equivalent in makes mentioned in Apx 'B'
Material and labour for Sub Main Wiring (in replacement) with two single core 4 Sqmm (nominal area) multi stranded copper conductor FRLS PVC insulated and unsheathed colour code cables, drawn in and including non-metalic rigid PVC conduit, heavy duty of 25 mm dia, including standard fittings such as Tees, junction, bands etc., conduit concealed in wall & fixed on ceiling with suitable clamps with and including one run of continuous multi stranded copper conductor 2.5 Sqmm (nominal area) FRLS PVC insulated and unsheathed colour code cable for earth continuity, 1100 volts grade , complete all as specified and directed. Note(s): (i) Two runs of 4 Sqmm main cable + one run of 2.5 Sqmm cable for earth continuity and PVC conduit shall be measured as one unit/one Running Metre. (ii) Rate quoted shall be deemed to include cutting chases for concealing conduit and making good in cement mortar (1:4) or PCC (1:2:4) as required.
Supply and fixing in replacement sheet metal enclosure, SPN, with a two pin socket and earth plug, with one MCB single pole, 240 Volts, 20 Amps, ‘B’ curve, 10 KA, complete all as specified and directed
INTERNAL ELECTRIFICATION WORK
Material and labour for point wiring with single core multi stranded copper conductor 1.5 Sqmm (nominal area) PVC insulated unsheathed FRLS colour code cable of 1100volts grade drawn through and including non metalic rigid PVC conduit medium duty of suitable size with all standard fittings such as Tee junction, bends etc, concealed in wall/fixed on ceiling including M.S. sunken boxes of suitable size made of 1.6mm thick MS sheet duly painted with anticorrosive paint, for housing switches, fan regulators etc. with PVC cover sheet 3mm thick (Make : Hylam, Plaza, Havells, Kalinga) including 1.5Sqmm (nominal area) multi stranded copper conductor PVC insulated unsheathed FRLS colour code cable of 1100volts grade for earth continuity, as for one light/exhaust fan/bell point or fan point (through regulator), controlled by one switch, complete all as specified and directed. Note(s) : (i) Rate quoted shall be deemed to include cutting chases for concealing conduit and making good in cement mortar (1:4) or PCC (1:2:4) as required. (ii). Switches and fan regulator etc., shall be measured and paid separately.
All as per item No 3.01 here-in-before but point wiring for one 3/5 pin socket outlet 5 Amps multipurpose socket outlet point on independent board complete all as specified and directed.
All as per item No. 3.01 here-in-before but point wiring using 2.5 sqmm as main wire & 2.5 Sqmm as continous earth wire, for one 15 Amps socket outlet point on independent board controlled by one single pole, one way switch complete all as specified.
Supply and fixing switch piano, flush type, single pole, one way, 6 Amps, 230volts, complete all as specified and directed.
Supply and fixing switch piano, flush type, single pole, one way, 16 Amp, 230 volts, complete all as specified and directed.
Supply and fix Socket outlet multipurpose 3/5 pin, 6 Amp, flush type, complete all as specified.
Supply and fix Socket outlet multipurpose 3/5 pin 6/16 Amp, flush type, complete all as specified.
Supply and fixing Distribution board sheet metal enclosures, TPN 415 Volts, 04 ways with 200 amps rated bus bar, double door, with IP 54 protection, complete all as specified and directed.
Supply and fixing MCBs Distribution board sheet metal enclosures, SPN 240 Volts, 02 way with 200 amps rated bus bar, double door for MCBs, with IP 54 protection, including blanking plate as required, including making good the disturbed surfaces to match with the existing, complete all as specified and directed.
Supply and fixing isolator TP 63 A 240 Volts complete all as specified and directed.
Supply and fixing MCB SP 06 to 32/40 Amps, 240volts, 'B' curve/ series, 10 KA, complete all as specified and directed.
Supply and fixing SPN 40 to 63 A rating 240 V, 10 KA 'C' curve miniature circuit breaker (MCB) in the MCB DB complete with connection testing and commissioning, complete all as specified and directed.
Supply and fixing wall mounting fan 230 Volts with 400 mm sweep, swing type, complete all as specified and directed.
Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable, complete all as specified and directed.
Material and labour for earthing complete with GI earth plate electrode of size 600mm x 600mm x 6mm thick burried directly in ground vertically (depth of pit not less than 2.25 m below normal ground level), with top edge of earth plate not less than 1.5m below normal ground level, earth plate surrounded from all sides by 15cm thick packed alternate layers of charcoal dust and common salt, electrode connections using galvanized iron wire 4mm dia (upto body of equipment) by means of nuts, bolts, check nuts & GI washers, connected to main switch board or main control board or test point, protected by galvanized iron pipe light grade 40mm dia bore, and watering pipe 20mm dia bore GI medium grade with funnel & wire mesh including all necessary excavation & earth work, PCC chamber in PCC (1:2:4) type B-1 & RCC cover, all as shown in electrical plate No 3 of MES Schedule Part-I (2009), testing on completion, complete all as specified and directed. Note(s) :- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with XPM not less than 4Kg/Sqm. (ii) PCC chamber shall be constructed 500 mm away from the edge of earth pit. (iii) Rate shall include GI strip and protection pipe of length 7.5m, excess beyond 7.5m length required at site shall be measured and paid separately. (iv) Earth resistance should be less than 3Ohm. In case the test results are not found below 3Ohm, complete earthing will be redone without any extra cost to Govt.
EXTERNAL ELECTRIFICATION WORK
Material and labour for earthing complete with GI earth plate electrode of size 600mm x 600mm x 6mm thick burried directly in ground vertically (depth of pit not less than 2.25 m below normal ground level), with top edge of earth plate not less than 1.5m below normal ground level, earth plate surrounded from all sides by 15cm thick packed alternate layers of charcoal dust and common salt, electrode connections using galvanized iron strip of size 32mmx6mm thick (upto body of equipment) by means of nuts, bolts, check nuts & GI washers, connected to main switch board or main control board or test point, protected by galvanized iron pipe light grade 40mm dia bore, and watering pipe 20mm dia bore GI medium grade with funnel & wire mesh including all necessary excavation & earth work, PCC chamber in PCC (1:2:4) type B-1 & RCC cover, all as shown in electrical plate No 3 of MES Schedule Part-I (2009), testing on completion, complete all as specified and directed. Note(s) :- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with XPM not less than 4Kg/Sqm. (ii) PCC chamber shall be constructed 500 mm away from the edge of earth pit. (iii) Rate shall include GI strip and protection pipe of length 7.5m, excess beyond 7.5m length required at site shall be measured and paid separately. (iv) Earth resistance should be less than 3Ohm. In case the test results are not found below 3Ohm, complete earthing will be redone without any extra cost to Govt.
Supply, laying (in replacement), jointing, testing and commissioning Low Tension (LT) XLPE insulated and armoured, heavy duty, electric power cable, cross sectional area 150 Sqmm 3.5 core aluminum conductor 1100 volts grade under ground cable including both side connection with cable lugs etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and as directed. Note: Excavation & earthork, sand cushioning and bricks for protection of cable shall be measured and paid separately.
Supply, laying (in replacement), jointing, testing and commissioning Low Tension (LT) XLPE insulated and armoured, heavy duty, electric power cable, cross sectional area 35 Sqmm 3.5 core aluminum conductor 1100 volts grade under ground cable including both side connection with cable lugs etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and as directed. Note: Excavation & earthork, sand cushioning and bricks for protection of cable shall be measured and paid separately.
Supply, laying (in replacement), jointing, testing and commissioning Low Tension (LT) XLPE insulated and armoured, heavy duty, electric power cable, cross sectional area 16 Sqmm 2 core aluminum conductor 1100 volts grade under ground cable including both side connection with cable lugs etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and as directed. Note: Excavation & earthork, sand cushioning and bricks for protection of cable shall be measured and paid separately.
Supply and fixing MCCB 4 pole 200 Amps, 50 Hz, 415volts, 25 KA, with enclosure, complete all as specified and directed.
Clean dry sand laid in trenches/ducts for bedding and cushioning to cable, 8cm in depth before laying the cable and 15 cm in depth after laying the cable including spreading, levelling and consolidation complete all as specified and directed. Note : Consolidated/punned thickness of 18 cm (overall) shall be measured for payment purpose.
Supply and laying well burnt sub class 'B' bricks for cable protection laid flat ,length wise, perpendicular to the axis of cable, complete all as specified.
COMMON ITEMS FOR BUILDING WORK AND EXTERNAL ELECTRIFICATION
Excavation in trenches in soft/loose soil not exceeding 1.50 meter wide and not exceeding 1.5 meter in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, for laying/taking out cables and foundations of poles etc . not exceeding 10 square metre on plan and not exceeding 1.5 metre in depth and getting out complete all as specified and directed.
Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick each as in soft/loose soil, complete all as specified and directed.
Removing of surplus soil / excavated material to a distance not exceeding 50 metre and depositing where directed at level not exceeding 1.5 metre above the starting point complete all as specified and directed.
Note: The Total amount shall subject to adjustment of credit of Rs. 450.00 for old Materials as per Schedule of Credit.
Babu Ram Sud and Sons
stage.html
html • 0.05 MB
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .