COMPREHENSIVE B/R REPAIRS INCLUDING INTERNAL WIRING IN CERTAIN MD AND OTM ACCNS IN CENTRAL SECTOR AT MIL STN KOTA

Amount

Taking down cement plaster of any description and thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Dismantling floor, hearth or wall tiling/ terrazzo including cement mortar bedding (but not backing), removing tiles and rubbish off the premises, complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors etc, laid, bedded and pointed in any mortar, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and pavings n.exc 15 cm thickness (below or above GL) and removing rubbish from premises, complete all as specified and directed.

Demolition/Dismantling of existing normal roof treatment, any type from RCC roof slab including lime concrete/PCC padding over roof, removing layer of bitumen under lime concrete/PCC padding, cement mortar, felt etc and cleaning the surface by hacking to receive plaster and removing demolished materials outside MD land, complete all as specified and directed.

Demolition of brick work/stone boulder masonry, built in CM incl all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed.

Taking down chowkhat or frames not exc 1.50 Sqm each with shutters (with out taking off shutters from the frame), complete all as specified and directed.

Taking down chowkhat or frames exc 1.50 Sqm and not exc 4.00 Sqm each with shutters (with out taking off shutters from the frame), complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm and not exc 2 Sqm each complete all as specified and directed.

Resecuring or easing and adjusting without taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each, complete all as specified and directed.

Resecuring or easing and adjusting without taking down shutters of any description not exceeding 1 Sqm each, complete all as specified and directed.

Dismantling cast iron or reinforced concrete concrete drain pipes 100 mm bore, jointed in CM and taking out from trenches if required, complete all as specified and directed.

Dismantling cast iron or reinforced concrete concrete drain pipes 75 mm bore, jointed in CM and taking out from trenches if required, complete all as specified and directed.

Taking up or down 15 mm dia steel tubing and connection including cleaning for refixing or removal to store, complete all as specified and directed.

Taking up or down 20 mm dia steel tubing and connection including cleaning for refixing or removal to store, complete all as specified and directed.

Dismantling of existing water storage tank of any description of capacity exc. 250 ltr but n.exc. 500 ltr, complete all as specified and directed.

Dismantling of existing water storage tank of any description of capacity exc. 500 ltr but n.exc. 1000 ltr, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, any thickness incl hooks and ridge as retrieved from site complete all as specified and directed.

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work (reinforcement cut as required to facilitate demolition) and removing rubbish from premises, complete all as specified and directed.

M & L for reinforced cement concrete 1:2:4 type B-1 (nominal mix) using 20mm graded crushed stone aggregate as in chajjas and the like complete all as specified and directed.

Form work (fair finished surfaces) to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, slabs, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to TMT bars complete all as specified and directed.

M&L for mild steel TMT bars 6mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, slabs, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to TMT bars complete all as specified and directed.

M&L for PCC 1:2:4 mix type B-0 (Using 12.5 mm graded stone agg) for roof padding, leveling course to receive floor finishes etc, complete all as specified and directed.

M&L brushing neat cement slurry with 3.00 kg cement per Sqm, complete all as specified and directed.

M&L for applying 20 mm thick screed in CM 1:3 on roof slabs with using liquid water proofing compound as per manufacturer's instructions, complete all as specified and directed. (Liquid WPC shall be measured and paid separately).

Supply only approved liquid water proofing compound, complete all as specified and directed.

M&L for cleaning of roof slab including picking, sweeping clean and washing down with water to remove dust, dirt etc and Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to IS 3384 @ of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of cold applied bituminous primer conforming to IS:3384 @ 0.40 Kg/Sqm.

Item 29.00 Contd........ (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm (minimum) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimney/other vertical surfaces and polymeric membrane inserted in groove and sealed with paving bitumen. (v) Cost of above aspects is deemed to be included in quoted rates.

M&L Framed work as in doors or gates of angles or other section with gusset plates, rails braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with including either hooks and hinges or steel hanging door fittings (excluding of steel sheeting or other covering running rails and guides) and hanging also fastening and fixing, conforming to Fe-290 Grade-E-165, complete all as specified and directed.

S & F rolled mild steel as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, conforming to Fe-410W Grade-E-250,quality 'B' complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering, wall cladding etc, fixed to iron/wooden members with self drilling zincoulium coated metal screws having cap with rubber and metal washers, complete all as specified and directed.

Dismantalling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Taking down wall panelling and similar work, including cover fillets complete all as specified and directed.

S&F Solid PVC Wall Lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing, complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing, complete all as specified and directed.

S&F of micro perforated square edge and attractive finish mineral fibre (sand micro) of nominal size 595x595x5-7 mm thick having building attribute as in false ceiling, fixed with and including grid of size 600x600mm having main frame of aluminium T of size 35x25x0.70 mm thick, cross aluminium T of size 25x35x0.70mm thick and wall angle of size 25x25x0.7 mm thick, the grid shall be suitable for mineral fibre tiles and hanging from soffits of existing RCC roof slab with using connecting/levelling clips, complete all as per manufacturer’s instructions, all as specified and directed.

S&F 35mm thick factory made IInd Class Hard wood (Hollock) paneled door shutters single panel with lock rail and panel of 9mm B.W.P. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to IS-710 or 12mm thick particle board veneered with commercial veneering on both faces. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S&F 35mm thick factory made IInd Class Hard wood (Hollock) glazed and skeleton, open rebated, prepared to receive glass, gauge etc, without sash bars, edges of framing plain, chamfered and rounded, fitted with cut and mitered beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

M&L for 25 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed.

S & F in renewal of 18-19mm thick MDF boards as in shelves and kitchen cabinets partitions complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing, complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and directed.

S&F mild steel framed work as in grills, grating etc. with end of bars shouldered and/or riveted, or forged into spikes: framed guard bars: barred iron doors: ladders: frame balusters: walk ways: railing: frame work of water tanks and similar works conforming to Fe-290 Grade-E-165, complete all as specified and directed.

S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium frame for doors, windows, ventilators, partitions with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21 100mm long (2 No.), suitable handle (1 No), complete all as specified and directed. Note :- Wire cloth & Glass pane shall be measured and paid for separately.

Supply only stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed. (Note: cost of fixing of wire cloth shall be deemed included in the unit rates of item No. 45.00 & 46.00 here-in-before.)

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in- charge.

S&F in renewal of door closer hydraulically regulated, aluminium extruded section, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm width and weight between 61 to 80 Kg and fixed, complete all as specified and directed.

S&F of floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length of cover plate 140 mm, complete all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section 150 mm long and fixed, complete all as specified and directed.

S&F aluminium handles, cast type, anodised 150 mm size, complete all as specified and directed.

S&F 100 mm size aluminium alloy hinges with steel hinge pin, ISI marked, complete all as specified and directed.

S&F in renewal of 200 mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

S&F in renewal of 300 mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F in renewal of 100 mm long hasp & staple safty type aluminium and anodised hinge pin bolt to hinge plate and fixed with screws all as directed.

S&F PVC bedding not exc 5 cm wide for entrance door complete all as directed.

S&F in renewal of SS brackets/bob as suitable for 20/25mm dia SS curtain rod of any shape and colour complete all as directed.

S & F in renewal of steel rolling shutters, 1.25mm thickness of laths without ball bearing, as specified including top cover, an choring rod, hasp and staple and one shop coat of primer; erected in position as indicated, gear operated type with bevel gear box and crank handle complete all as specified and directed. Note :- Cost of new parts as a 'Supply only' shall be measured & paid under respective items of BOQ.

Supply only safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

Supply only ball bearing for rolling shutters complete all as specified and directed.

M&L for welding in repair not exc. 2.5 cm in length, thickness of metal to be welded n. exc. 6 mm complete all as specified and directed.

M&L for welding in repair exc 2.5 cm but not exc. 5 cm in length, thickness of metal to be welded n. exc. 6 mm complete all as specified and directed.

S&F in renewal of stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised/SS wire staples in door & steel window complete all as specified and directed.

Hacking out old broken glass (any thickness size, quality or description) from wooden frame/metal frame, glazing with putty or fixed with beads complete all as specified and directed.

S&F sheet glass 3mm thick ordinary quality and glazing with oil putty etc in squares n.exe 0.50 Sqm in each pane, complete all as specified and directed.

S&F 3mm thick figured glass pin head type and glazing with oil putty etc in squares n.exe 0.50 Sqm in each pane, complete all as specified and directed.

M&L Glazed ceramic coloured tiles on vertical surfaces 350x 250x7 mm/450X350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick rendering in CM 1:4 backing, complete all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B-1 (using 25 mm graded stone aggregate) as in flooring/sub base finished rough to receive floor finishes/screed complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, fixed on vertical surfaces, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 10 mm thick rendering in CM 1:4, complete all as specified and directed.

M&L for machine cut kota stone slab as in flooring 20 to 25 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing, laid over and including 20 mm thick screed bed in CM 1:6, complete all as specified and directed.

~Ditto- all as per item No 75.00 (here-in-before) but except kota stone slab complete all as specified and directed.

M&L for machine cut kota stone slab as in skirting, dado, risers etc, 20 to 25 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing, laid over and including 10 mm thick rendering in CM 1:4, complete all as specified and directed.

M&L for green marble slab 18-20 mm thick (table rubbed and polished) fixed as in cooking plateform, steps, treads, risers, jambs, window cills etc and the like set in cement mortar 1:4 and pointed with white cement using marble dust with admixture of pigment to match the shade of stone, laid over and including 20 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L granite slab 16-18 mm thick, table rubbed and polished in cooking platform, jambs, cills, pillars, tread, risers, platform for WHB etc including bull nosing to exposed outer edges, set in CM 1:4 bedding and pointing with white cement mixed with pigment, laid over and including 20 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L 100 mm thick PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in sub base of floors etc, finished fair and even to receive floor finishes complete all as specified and directed.

M&L for laying full body vitrified matt finish paving tiles of size 300x300x10mm thick suitable for exterior areas, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles confirming as per IS 15622:2017, laid over and including 15 mm thick screed in CM 1:6, complete all as specified and directed.

M&L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:4, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of ceiling in cement mortar 1:3 including finishing the surface even and smooth, complete all as specified and directed.

M&L brick work with pulverized fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan exc 6 m mean radius, built in CM 1:6, complete all as specified and directed.

M&L walling of random rubble, uncoursed well bonded, bedded and solidly hearted, built in Cement Mortar 1:6, including finishing the joint, flush as the work proceeds complete all as specified and directed.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface n exc. 40mm to face stones and dressing or face beds and joints, as specified, of random rubble walling, uncoursed or bourght upto courses complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surface in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggreate), 75 mm thick as in plinth protection/Path/PCC paving etc including finishing the surface even & smooth without using extra cement, with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where dirtected and providing 6 mm wide joints throughout the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three parts of fine sand by weight), complete all as specified & directed.

Cleaning and removing all scale and dirt, etc., from existing water tanks and from mouths of circulating pipe etc., capacity of tank exc. 250 ltr but n.exc. 500 ltr, complete all as specified and directed.

Cleaning and removing all scale and dirt, etc., from existing water tanks and from mouths of circulating pipe etc., capacity of tank exc. 500 ltr but n.exc. 1000 ltr, complete all as specified and directed.

S&F in renewal of PVC lid in round shape including hinging device with locking arrangements as suitable for existing PVC water tank complete all as specified and directed.

S&F in position rotational moulded polyethylene water storage tanks 500 ltrs capacity, white colour (cylinderical vertical with closed top) hoisted and fixed in position, complete all as specified in SSR Part I and as directed. Note:- PVC tank shall be ISI marked and having three layers.

S&F in position rotational moulded polyethylene water storage tanks 1000 ltrs capacity, white colour (cylinderical vertical with closed top) hoisted and fixed in position, complete all as specified in SSR Part I and as directed. Note:- PVC tank shall be ISI marked and having three layers.

S&F 20 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe, complete all as specified and directed.

S&F in renewal of 20 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe, complete all as specified and directed.

S&F in renewal ofs 'D' type towel rail 60 cm long, stainless steel, fancy type, 20 mm dia complete fixed with steel screws complete all as specified and directed.

Supply, fixing, laying & testing 15 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed.

Supply, fixing, laying & testing 20 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed.

Refixing old steel tubing (With and including new GI fittings) in new or old position (Wall, Ceiling, floor etc) of 15 mm dia pipe complete all as specified and directed.

Refixing old steel tubing (With and including new GI fittings) in new or old position (Wall, Ceiling, floor etc) of 20 mm dia pipe complete all as specified and directed.

S&F in renewal of shower rose, brass, CP, fancy type, 125 mm size with swivel joint, screwed to iron pipe or for union of 15 mm dia complete all as specified and directed. Make :- CERA Cat No F7020111AB/ Hindware Cat Part No F 160142 / JOHNSON cat No. JF 803899 or techno commercially equivalent makes specified in PS.

S&F in renewal of PVC connection 450 mm long suitable for 15 mm GI pipe with two PTMT nuts and rubber washers complete all as specified and directed.

S&F in renewal of stop valves 15 mm nominal bore, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F in renewal of 15mm bore mixture valve chromium plated fancy type for wall in two/three pin fixed to iron pipe all as complete all as specified and as directed. Make :- CERA Cat No. F1001411 /JAQUAR Cat No. QQP7273PM /Hindware Cat No. F 74022 or techno commercial equivalent Make as speicifed in PS.

S&F in renewal of 15mm bore mixture valve chromium plated fancy type for wash hand basin centre hole fixed to iron pipe complete all as specified and as directed. Make :- CERA Cat no. F1003461 /JAQUAR cat no. QQP 7167 BPM /Hindware Cat no. F 740009 or techno commercial equivalent Make as speicifed in PS.

S&F in renewal of angle stop valve 15 mm nominal bore cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed one end for iron pipe or for union and fixed, complete all as specified and directed.

S&F in renewal of 2 in 1 angle valve 15 mm nominal bore CP fancy pattern type, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed one end for iron pipe or for union and fixed, complete all as specified and directed. Make :- CERA Cat no. G1017211 /JOHNSON JT 1643A / Hindware Cat no. F 740006 or techno commercial equivalent Make as speicifed in PS.

S&F in renewal of stop valve 20 mm nominal bore cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and directed.

S&F in renewal of long body bib taps, cast copper alloy, chromium plated, screwed down, screwed for 15 mm dia GI pipe or for brass ferrule or to GI socket complete all as specified and directed. Make :- Cera cat No. G1017152 /JAQUAR cat No. VGP-81037 /Hindware Cat No. F 740011 or techno commercially equivalent makes specified in PS.

S&F in renewal of vitreous china squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including PVC(SWR) 'P' or 'S' trap connecting to flush pipe and to anti syphonage pipe, including making good to floor complete all as specified and as directed.

S&F in renewal of vitreons china wash down water closet pan, padestal type, white, with 'p' or 's' trap & including recessed bottom PVC seat cover of white colour and mild steel chromium plated hinging device but excluding flushing cistern, flush pipe and fixing bolt and making connections to drain or outgoing pipe and to flushing pipe, anti-syphonage pipe etc, fixed in repairs, complete all as specified and directed. Make :- CERA Cat No Conventional Pro 520*360*390, S1059101/ JAQUAR Cat No. CWS WHT-551PNPP1841Z/ JOHNSON Cat No. J 8312 or techno commercially equivalent makes specified in PS.

Supply and fix in renewal of PVC valveless, syphonic action type, flushing cistern, 10ltr capacity, low level, white, with inlet, ball valve, float and handle including brackets, connections to pipes and fixing of chain and pull, or lever, complete all as specified and as directed.

S&F in renewal of single unit floor mounted/wall hung european water closet set & including wall hung cistern with lid of suitable capacity, ultra solid wall hung fittings such as seat cover etc and including making all necessary connection complete all as directed. Make :- Cat Part No-E-1567 of Hindware / Cat Part No. CES-6356 of Cera/ Cat Part No C8854 of Parryware or techno commercially equivalent makes specified in PS.

S&F in renewal of wall mounted pull it aluminium cloths drying system with L angle 31'' for 4 pipe system with length of each pipe 5 ft (1.53 mtr) i.e. total length of 20 ft (6.12 mtr) complete all as specified and directed.

Supply and fix in renewal of vitreous china wash basin white counter sunk type, size 580x430 mm & including 32 mm dia CP waste fitting and PVC waste pipe 610 mm long and brackets complete all as specified and directed. Make :- CERA Cat No S 2040109/ JAQUAR cat No. OPs WHT-1580I/JOHNSON Cat No J8396 CH or techno commercially equivalent makes specified in PS.

S&F in renewal of vitreous china counter wash hand basin white on granite slab, with flat back of size 550x400 mm, fitted with granite stone slab excluding chain and plug, taps and porcelain stopper but incl PVC waste pipe of 32 mm bore, 32mm dia wast coupling & its fittings, long screwed shanks and fly-nuts, flange end bedded in red lead cement, complete all as specified and directed. Note :- Granite stone slab shall be measured and paid separately under appropriate item of BOQ.

S&F vitreous china half stall type urinal, white with grating and union for discharge pipe, including providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back with white cement, complete all as specified and directed.

S&F urinal spreader of PTMT (Minimum weight 60 Gms), any colour for fixing with 15 mm dia pipe, complete all as specified and directed.

S&F in renewal of 75 mm dia PVC (SWR) floor trap, with CP grating including jointing to waste pipe with solvent cement and fixed in cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) complete all as specified and directed.

S&F in renewal of 75 mm dia cast iron floor trap, with CP grating including jointing to waste pipe with solvent cement and fixed in cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) complete all as specified and directed.

S&F in renewal of 100 mm dia cast iron nahani trap with stainless steel grating including jointing to waste pipe in run lead, complete all as specified and directed.

S&F in renewal of 75 mm dia cast iron nahani trap with stainless steel grating including jointing to waste pipe in run lead, complete all as specified and directed.

S&F cast iron (sand cast) soil, waste and vent pipe 100 mm bore in any length with or with out ears with cement joints laid in trenches or fixed to walls, complete all as specified and directed.

S&F cast iron (sand cast) soil, waste and vent pipe 75 mm bore in any length with or with out ears with cement joints laid in trenches or fixed to walls, complete all as specified and directed.

S&F 100 mm bore CI bend (any radius), diminishing pieces or tapers (larger bore measured), complete all as specified and directed.

S&F 75 mm bore CI bend (any radius), diminishing pieces or tapers (larger bore measured), complete all as specified and directed.

S&F stack clamps made out of 20x5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, dia of pipe 100/110 mm, complete all as specified and directed.

S&F stack clamps made out of 20x5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, dia of pipe 75/80 mm, complete all as specified and directed.

S&F in renewal of PVC (SWR) pipe 75 mm bore, single socketed, in any length with rubber ring joints and fixed to walls, complete all as specified and directed.

S&F in renewal of PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and fixed to walls, complete all as specified and directed.

S&F PVC (SWR) bend 75 mm bore, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F PVC (SWR) bend 110 mm bore, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F PVC (SWR) 110 mm bore junction single,(Single T) equal or unequal, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

S&F PVC (SWR) 75 mm bore junction single,(Single T) equal or unequal, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

S&F in renewal of welded steel wire fabric fixed to steel members, (weight per Sqm not exceeding 4.00 kg), complete all as specified and directed.

S&F in renewal of pillar taps, 15 mm dia, cast copper alloy, fancy type, swan neck type with capstan heads, with chromium plated, screwed down high pressure with or without lettered 'hot' or cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. Make :- CERA Cat No. F1003103 /JAQUAR cat No. COP-021PM /Hindware Cat No. F 74002 or techno commercially equivalent makes specified in PS.

S&F in renewal of 32 mm bore waste fittings brass CP for wash hand basin etc with long screwed and fly nuts, flange end embedded in red lead cement and other end fixed, complete all as specified and directed.

S&F in renewal of grating doom of 100 mm dia, made of PTMT with or without waste hole (Minimum weight 25 gm), complete all as specified and directed.

M&L for preparing new steel surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer, complete all as specified and directed.

M&L applying 2 coats of synthetic enamel paint over and including a coat or pink primer on wooden surfaces, exceeding 10 cm in width or girth, incl preparation of the new surfaces complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying 1 mm thick wall care putty as per manufacturer's instructions and over it applying two coats of distemper oil emulsion over & including one coat of suitable primer, complete all as specified and directed.

M&L applying three coats of white wash after preparation of new plastered surfaces of ceiling, complete all as specified and directed.

M&L for applying two coats of cement based paint on newly plastered surfaces of walls over & including a coat of white wash including preparation of surfaces, complete all as specified and directed.

S&F in renewal ofs PTMT alloy toilet cabinet with mirror of overall size 350x450 mm and fixed to wall complete all as specified and directed, complete all as specified and directed.

S&F in renewal of stainless steel tubular curtain rods, 25 mm dia, with fixing brackets and one pair of decorative end caps etc, complete all as specified and directed.

S&F in renewal of ABS body health faucet (Bidet spray), chrome finish, including 15 mm dia chromium plated pop up connection pipe of minimum 1.00 m length with CP brass nuts, incl wall hook, complete all as specified and directed. Make:- Cera Model F 8030105AB (ABS)/ JAQUAR ALD-565/JOHNSON J f8082A or techno commercially equivalent makes specified in PS.

S&F in renewal of flushing jet CP for WC (pedestal pattern) & including PVC nozzle and flexible pipe of 1150mm long, nuts& bolts, fixed to WC, complete all as specified and directed.

S&F in renewal of PVC waste pipe 32/40 mm dia and 1150 mm long, suitable for wash hand basin etc, complete all as specified and directed.

S&F in renewal of plastic water closet seat cover, white with recessed bottom and mild steel chromium plated hinging device, complete all as specified and directed.

S&F in renewal of Toilet paper holder Vitreous China (Coloured), box type, complete all as specified and directed.

S&F in renewal of Soap dish, Stainless steel, embedded in the wall complete all as specified and directed. Make :- CERA Cat no. F5013106CH /JAQUAR cat no. AKP 35731p / Hindware Cat no. F 450022 or equivalent makes as per PS.

S&F in renewal of CP Towel ring with and including CP brass screws and cleats complete all as specified and directed. Make :- CERA Cat No. F5013115CH/JAQUAR cat No. CAN-1121N/ Hindware Cat No. F 580003 or techno commercially equivalent makes specified in PS.

S&F in renewal of corner glass shelf assembly of 6 mm thick glass, 12 cm wide and 60 cm long and CP guards of approved quality and fixed to wall with CP brass screws, brackets etc, complete all as specified and directed.

S&F in renewal of stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets of suitable angle iron, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm, 32 mm dia superior quality PVC waste pipe and connecting union to pipe complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for reuse or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Dismantling unserviceable main switch/DBs incl wooden board and deposit to MES store yard including making good disturbed surface of wall complete all as specified and directed.

Taking down sub main wiring of any size/capacity complete all as specified and making good disturbed sufaces to match with the existing surface, complete all as specified and directed.

M&L for Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface including providing wooden/PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover and making good disturbed surfaces, complete all as specified and directed for the following: - One light/ceiling fan/exhaust fan/bell buzzer point controlled by one, one way switch of 5/6 Amps.

All as per item No 160.00 (here-in-before) but one 5 Pin, 5/6 amps socket outlet point on independent board, controlled by one, one way 5/6 Amp switch.

All as per item No 160.00 (here-in-before) but one 5 Pin, 5/6 amps socket outlet point on same board, controlled by one, one way 5/6 Amp switch.

All as per item No 160.00 (here-in-before) bu One light point controlled by two 2 way 5/6 Amp switches.

M&L Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 2.5 Sqmm, with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable FRLS of size 2.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface for one socket outlet 15 amp on independent board including providing wooden rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover and making good disturbed surface, complete all as specified and directed.

S&F switch piano flush type 5/6 Amps, 230 volts, single pole, one way, ISI marked, complete all as specified & directed.

S&F switch piano flush type 5/6 Amps, 230 volts, single pole, two way, ISI marked, complete all as specified & directed.

Supply and fixing switch socket combination, 5/6 and 15/16 Amps, 230 volt, multi pin, flush type universal, ISI marked, complete all as specified and directed.

Supply and fixing socket outlet, 5/6 Amps, 230 volt, five pin, flush type universal, ISI marked, complete all as specified and directed.

S&F in renewal of stepped type electronic fan regulator, flush type, 230 volts AC, single pole, humming free, fixed on the existing phenolic laminated sheet, complete all as specified and directed.

S&F ceiling rose surface type PVC/Polycarbonate isolated body, 65x 20mm, 3 terminals, complete all as specified & directed.

S&F PVC/polycarbonate lamp holder, angular/batten type with back plate, complete all as specified & directed.

S&F bell push, flush type, single pole, AC, 240 volts, 5/6 amps, ISI marked, complete all as specified and directed.

S&F in renewal of electronic call bell, ding dong type, single pole, 230 volts AC, complete all as specified and directed.

S&F in renewal of wall mounted 20 watt LED Tube light fittings, batten type with bipin holders, powder coated steel with internally prewired, complete all as specified and directed.

S&F in renewal of wall mounted 10 watt LED Tube light fittings, batten type with bipin holders, powder coated steel with internally prewired, complete all as specified and directed.

S&F in renewal of LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S&F in renewal of LED street light fitting 35 Watt, 230 V AC outdoor type with high pressure diecast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 250mm and taking down old existing unserviceable fan, complete all as specified and directed.

S&F MCB, 6 to 32 Amps, Single Pole, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S&F MCB, 6 to 32 Amps, Single Pole & Neutral, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S&F MCB, 63 Amps, Triple Pole & Neutral, 415 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

M&L for MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, earth bar and Din rail, 415 Volts TPN with 4 ways, Double door, complete all as specified and directed.

M&L for MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, earth bar and Din rail, 240 Volts SPN with 8 ways, Double door, complete all as specified and directed. Note for items of MCB DB - (1) The unit rate includes for cutting the brick walls to accommodate DB to make flush to wall. (2) The unit rate includes for making good the disturbed surfaces including finishes to match with the adjoining surface.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed FRLS multistranded copper conductor cable of size 6 Sqmm LT, 1100 volts grade, drawn through and including 20 mm dia PVC non metallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded FRLS copper conductor cable green colour as earth continuity conductor, complete all as specified & as directed. NOTE:- Two runs of cable one run of earth wire and one run of PVC non metallic conduit of 20mm dia shall be measured as one run length. Cable required for connection to DBs shall deemed to be included and shall not be measured separately. Earth wire shall run inside the PVC conduit.

M&L for Earthing with galvanized steel earth plate electrode of size 600 mm x 600mm x 6.0 mm, buried directly in ground (earth plate not less than 2.25 Mtr below normal ground level) connected to galvanized iron earth wire of 4 dia by means of bolts, nuts, check nuts and washers of galvanized iron including 15 mm bore light grade GI tubing for protection of earth wire, MS sheet metal funnel with wire mesh, watering pipe medium grade 20 mm bore, charcoal or coke and common salt in alternative layer of 15 Cm compacted thickness all around the electrode with concrete earth pit of PCC 1:3:6 type 75 mm thick precast RCC (1:2:4) type B1 pit cover reinfored with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar and necessary excavation, earth work, in soft/loose soil and disposal of spolis to a distance not exc 50 Mtr and necessary connection and testing complete all as shown in electrical plate No. 5 and including dismantling and taking out old earthing complete all as specified and directed. Notes: - (a) Irrespective of whatever is shown in plate No 5 of SSR, earth pit shall be casted in PCC (1:3:6) type C-1 and precast cover of RCC (1:2:4) type B-1 with suitable handle. (b) Item includes the cost of GI pipe for protection of earth wire and earth wire upto 7.5 m. Any variation below or above shall be measured and paid for separately under relevant item of this Sch ‘A’.

M/S MOHINI ENTERPRISES

S.S ENTERPRISES

SARDAR PATEL ENTERPRISES

ANNAPURNA ENTERPRISES

TARKESHWAR DASS CONSTRUCTION COMPANY

SINGH ENTERPRISES