Construction of Ramanattukara Municipal Office Building - Retender

Amount

NEW OFFICE BUILDING - CIVIL

2.31 : Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

od197044/2020_2021 : Filling with contractor own earth (excluding rock) in open areas in layers not exceeding 20 cm in depth, consolidating each deposited layer by rolling with power roller of minimum 8 tonnes, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge.

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

od187229/2020_2021 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. All work upto plinth level

od187257/2020_2021 : Extra for providing richer mixes at all floor levels. Providing M-30 grade concrete instead of M-25 grade BMC/RMC.

od187280/2020_2021 : Extra for providing richer mixes at all floor levels. Providing M-35 grade concrete instead of M-25 grade BMC/RMC.

od187300/2020_2021 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. All work above plinth level upto floor V level

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

20.2.4 : Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap).500 mm dia piles

20.2.5 : Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap).600 mm dia piles

od184175/2020_2021 : Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap). 700 mm dia piles

od197057/2020_2021 : Boring by mechanical means including diamond core cutting in hard rock for pile socketing, including getting out the excavated material and disposal of surplus excavated material as directed, within a lead of 50 m. (For 500mm, 600mm, 700mm piles)

od199665/2020_2021 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge. Single pile above 50 tonne and upto 200 tonne capacity Initial test

od199672/2020_2021 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge. Single pile above 50 tonne and upto 200 tonne capacity Routine test

15.2.1 : Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

50.6.1.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 (1 cement: 6 coarse sand) etc complete.

50.6.1.3 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure above floor two level up to floor V level thickness 20cm and above in: CM 1:6 (1 cement :6 coarse sand) etc complete

6.27.2 : Brick work with common burnt clay modular bricks of class designation 7.5 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand). Above plinth level and upto floor V level

od149727/2020_2021 : Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:6 (1 cement : 6 coarse sand)

13.1.1 : 12 mm cement plaster of mix:1:4 (1 cement : 4 fine sand)

13.16.1 : 6 mm cement plaster of mix:1:3 (1 cement : 3 fine sand)

od147534/2020_2021 : Providing and laying LEPPATO FINISHED Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Architect.

od147536/2020_2021 : Labour for fixing, edge rounding and final polishing of Granite edges for steps an etc

8.13.1 : Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye orequivalent.

od197193/2020_2021 : Providing and laying full body vitrified matt floor tiles in different sizes (10-15mm thickness) with water absorption less than 0.08% and conforming to IS : 15622, of approved make like Johnson/ Kajaria/ Rak/ Nitco/ Equivalent with a basic price of not less than Rs.1100/sqm in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600 x 600 mm.

od197195/2020_2021 : Providing and laying full body Vitrified matt tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make like Johnson/ Kajaria/ Rak/ Nitco/ equivalent with a basic price not less than Rs.1100/sqm, in all colours & shade, in skirting, recessed into wall, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm

od197197/2020_2021 : Providing and laying full body vitrified matt floor tiles in different sizes (10-15mm thickness) with water absorption less than 0.08% and conforming to IS : 15622, of approved make like Johnson/ Kajaria/ Rak/ Nitco/ Equivalent with a basic price of not less than Rs.1500/sqm in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600 x 600 mm

od197201/2020_2021 : Providing and laying full body Vitrified matt tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make like Johnson/ Kajaria/ Rak/ Nitco/ equivalent with a basic price not less than Rs.1350/sqm, in all colours & shade, in skirting, recessed into wall, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm

od197203/2020_2021 : Providing and laying full body vitrified matt floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make like Johnson/ Kajaria/ Rak/ Nitco/ Equivalent with a basic price of not less than Rs.680/sqm in all colours and shades except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600 x 600 mm.

od197204/2020_2021 : Providing and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make like Johnson/ Kajaria/ Rak/ Nitco/ equivalent with a basic price not less than Rs.300/sqm, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge, in skirting, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

od197206/2020_2021 : Providing and laying matt finished heavy duty vitrified tile of size 450x450x12mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make like Johnson/ Kajaria/ equivalent with a basic price not less than Rs.645/sqm in all colours and shades in for outdoor floors such as court yard etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

od183310/2020_2021 : Providing and paving baby chips around the building

od147554/2020_2021 : Providing and fixing of 15cm height platform making with 16mm marine plywood IS710.Grd top panel placed on proper reinforced double thick same grade plywood structures

2.35.3.1 : Diluting and injecting chemical emulsion for POST -CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion):Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

od197207/2020_2021 : Providing and laying semi polished, flamed Cerastone or equivalent (4inch thick) of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, with Buffalo grass in the gap of 2cm including all labour, material, etc. all complete as per the direction of Engineer-in-charge.

8.2.1.1 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Raj Nagar Plain white marble/ Udaipur green marble/Zebra black marbleArea of slab upto 0.50 sqm

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.47.1 : Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

13.48.1 : Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm

12.20 : Providing and laying pressed clay tiles ( as per approved pattern 20 mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand mixed with 2% integral water proofing compound, laid over a bed of 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete

9.117.1 : Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1 mm), with wall thickness 2.0mm (±0.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 x 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification and direction of Engineer-in-chargeExtruded section profile size 48x40 mm

9.118.2 : Providing and fixing to existing door frames30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge.

od197208/2020_2021 : Providing and fixing factory made uPVC white colour casement / casement cum fixed louvre window uPVC frame along with louvres. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge.

od194725/2020_2021 : Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door with 6mm thick toughened glass comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.

od197219/2020_2021 : Providing and fixing factory made uPVC white colour sliding glazed door with 6mm toughened glass comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Two track two panels sliding door made of (big series) frame 67 x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm)

9.147A.1 : Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 +/- 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.)

9.147A.3 : Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Casement window double panels with top fixed with S.S. friction hinges (350 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazingbead of appropriate dimension. ( Area of window upto 2.50 sqm).

9.147B.1 : 543 SUB HEAD : 9 - WOOD & PVC WORK 9.147B Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

od147566/2020_2021 : Providing and fixing in position wall panelling at all heights with Saint gobain approved by the Architect, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be in-serted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer's specification as per direction of Engineer-in-Charge all complete. With 15 mm thick fully perforated square/butt edge light weight calcium silicatepanels/ tiles

od178886/2020_2021 : Providing and fixing Fibre (high impact poly propelene reinforced) cement sheet of good quality in all colours with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers or with self drilling fastener and EPDM washer etc. complete:

od147569/2020_2021 : Providing & fixing false ceiling at all heights with with 40mm thick Alfaa sandwich panel grey coloured be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.

10.2 : Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

13.61.1 : Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

od147570/2020_2021 : Providing & fixing on decorativetile paving of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately)

od194803/2020_2021: Providing at all heights, levels and locations powder coated Aluminium trafford sheet 0.50mm thick (Jindal/ Oralium/ Hindalco/ Everlast/ Equivalent). The sheet shall be fixed using self drilling/self tapping SS screws of size 5.5x65 mm with EPDM seal complete upto required pitch in horizontal, vertical or curved surfaces i/c cutting to size and shape whereever required as per specifications, detail drawings and direction of Engineer-in-Charge. The rate shall be inclusive of all screws, seal, ridge, labour, scaffolding, machinery for fixing and approved sealent wherever required etc. but excluding the cost of purlins, rafters and trusses.

od194805/2020_2021 : Providing at all heights, levels and locations powder coated Aluminium Corrugated sheet 0.46mm thick (Jindal/ Oralium/ Hindalco/ Everlast/ Equivalent). The sheet shall be fixed using self drilling/ self tapping SS screws of size 5.5x65 mm with EPDM seal complete upto required pitch in horizontal, vertical or curved surfaces i/c cutting to size and shape whereever required as per specifications, detail drawings and direction of Engineer-in-Charge. The rate shall be inclusive of all screws, seal, ridge, labour, scaffolding, machinery for fixing and approved sealent wherever required etc. but excluding the cost of purlins, rafters and trusses.

od194806/2020_2021 : Providing and fixing M.S. round or square bars with M.S. flats at required spacing in frames of windows by welding including priming coat with approved steel primer, all complete as per directions of Engineer-in-charge

od178568/2020_2021 : Providing and fixing stainless steel Brushed mat finish (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) Weight of steel should check in site and measurement taken in kg.

10.26.1 : Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.M.S. tube

12.51.6 : Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) total coated thickness, zinc coating 120 grams per sqm as per IS:mm(+0.05%) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws complete:Gutter (600 mm over all girth)

21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

od197225/2020_2021 : Providing and fixing 8mm thick toughened glass panes (Saint Gobain/ Borosil/ La-Opala/ Equivalent) in aluminium partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. (Cost of aluminium snap beading and aluminium structure shall be paid separately)

od197226/2020_2021 : Providing and fixing 6mm thick toughened glass panes (Saint Gobain/ Borosil/ La-Opala/ Equivalent) in uPVC doors with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. (Cost of shutters paid separately)

21.3.1 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

od195096/2020_2021 : Providing & fixing coloured float glass panes with putty and glazing clips in uPVC Ventillators all complete as per the drawings and directions of the Engineer-in-charge. 5.5 mm thick glass panes

22.6 : Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : a) after surface preparation, first layer of slurry of cement @ 0.488 kg/ sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. laying second layer of fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/ sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tilling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured)

16.69 : Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand) , including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-Charge)

od178633/2020_2021 : Providing and Planting of Buffalo grass for Lawn in Ordinary soil including Breaking clods, Watering, Ramming and Sectioning of spoil bank etc., including all labour charges, etc., complete

od147572/2020_2021 : WATER CUTTING Providing and casting water cutting with Cement mortar 1:4 with specified measurement according to the direction of the engineer in site and as per the architectural drawing

od195102/2020_2021 : Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing as per the directions of the Engineer-in-charge

od195117/2020_2021 : Providing and fixing Glass Reinforced Jali works in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement mortar 1:2 (1 White cement : 2 stone dust) with an admixture of pigment, matching the stone shade, jali slab without any chamfers etc.

od195129/2020_2021 : Providing cement plastering of 12 mm cement plaster of mix 1:4 (1 cement : 4 fine sand) with chicken mesh in column-wall and beam-wall joints as per the directions of the Engineer-in-charge

od147578/2020_2021 : Exposed concrete

od178881/2020_2021 : Providing & fixing Stainless steel lettering for nameboard as per the size mentioned in drawing and quality approved by the Architect including labour charges etc complete - Size of the lettering is 20cm width, 25cm height, 3.3cm thickness each on granite slab fixed in the compound wall

od195131/2020_2021 : LANDSCAPING TREES - Digging pits in all kinds of soil and refilling the same with good quality fertile and earth, river sand, dried cow dung manure and leaf mould mixed in the ratio of 1:1:1:1, removal of rubbish and surplus earth if any, including lead lift etc as directed by engineer in charge and planting trees supplied with roots covered with appropriate natural containers from the source of availability including all complete

od147580/2020_2021 : SHRUBS: Digging pits in all kinds of soil and refilling the same with good quality fertile and earth, river sand, dried cow dung manure and leaf mould mixed in the ratio of 1:1:1:1, removal of rubbish and surplus earth if any, including lead lift etc as directed by engineer in charge and planting trees supplied with roots covered with appropriate natural containers from the source of availability including all conveyance, transported without any damage to the root.

od147581/2020_2021 : CREEPERS: Planting creepers 60cm center (type of creeper specified below) by excavating trenches of size 30x30x30cm and refilling with good quality fertile red earth, river sand, dried cow dung manure and leaf mould mixed in the ratio 1:1:1:1, removal of rubbish and surplus earth if any, including leaf lift etc. as directed by engineer in-charge and supplying good healthy cuttings of creepers free of all pests and deseases from source of availability including all conveyance caring and protecting the creeper etc. complete cutting of minimum 60cm length.

od147583/2020_2021 : DUST BIN: Providing and fixing Dust bin inside of park and parking area. including cost of all items. as per design drawings including all necessary labour, lead, lift, etc. complete.

od147584/2020_2021 : ADVERTISEMENT BOARD: Providing and fixing advertisement board. as per design and drawings including all necessary labour, lead, lift, etc. complete - Board with GI Sheet of 1.2mm thickness having a dimension of 2x2.5m fixed on 2” GI pipes of 3mm thickness painted with epoxy paint and lettering

RETAINING WALL and COMPOUND WALL

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for: Foundations, footings, bases of columns, etc for mass concrete

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

50.6.1.1 : Solid block masonry using pre cast solid blocks ( factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part 1 of 1979 for foundation and plinth with thickness 20 cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

6.27.1 : Brick work with common burnt clay modular bricks of class designation 7.5 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand).From ground level upto plinth level

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.47.1 : Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

10.1 : Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

13.61.1 : Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

OPEN WELL

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

od147435/2020_2021 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials. All kinds of soil

od147439/2020_2021 : Extra for open well excavation in all classes of soil from 3 - 4.5m

od147443/2020_2021 : 4 Extra for open well excavation in all classes of soil from 4.5-6m

od147447/2020_2021 : 5 Extra for open well excavation in all classes of soil from 6-7.5m

od147453/2020_2021 : Extra for open well excavation in all classes of soil from 7.50 - 9.00 m

od147457/2020_2021 : Extra for open well excavation in all classes of soil from 9.00 - 10.5 m

od147462/2020_2021 : Extra for open well excavation in all classes of soil from 10.5 - 12.00 m

od147467/2020_2021 : Extra for open well excavation in all classes of soil from 12 - 13.5m

od147474/2020_2021 : Extra for open well excavation in all classes of soil from 13.5 - 15.00 m

60.2.2 : Bailing out water Using 5HP Pump- Bailing out water with 5HP engine and pump set including conveyance to site and erection,cost of fuel, lubrication oil and other stores, pay of staff etc complete

50.5.7 : Reinforced cement concrete work in well-staining excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1. 5:3 ( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.9.12 : Centering and shuttering including strutting, etc. and removal of form for:Well steining

13.16.1 : 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

Gate & Car Park

10.25.2 : Item Shifted to head 14 as item 14.74Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

50.12.2.1 : Providing & fixing Poly carbonate corrugated sheet 0.8 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 M or as decide by the Engineer in charge. The sheets shall be fixed using self drilling / self tapping screw of size (5.5x55 mm) with EPDM seal complete upto any pitch in horizontal/ vertical/ curved surface, but excluding the cost of purlins, rafters, trusses, and including cutting to size shapes where ever required.

PLUMBING ESTIMATE

od199921/2020_2021 : Providing and fixing white vitreous china extended wall mounted European water closet of size 780x370x690 mm of approved shape and of superior quality with a price not less than Rs.7000/each, including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre /8 litres), including seat cover, angle cock and health faucet (all of make Jaquar/ equivalent), 15mm dia flexible water inlet pipe, 32mm dia pvc flush pipe, and cistern fittings, nuts bolts and gasket, connection to the soil line core cutting, refinishing etc complete as per the directions of the Engineer-in-charge

od199923/2020_2021 : Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar and angle cocks of approved make (Jaquar/ equivalent), 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin half pedestal of size 630x450 mm (price not less than Rs.1500/each) with a pair of 15 mm C.P. brass pillar taps

od200635/2020_2021 : Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, angle cock and health faucet (all of superior quality like Jaquar/ equivalent) with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required: Single half stall urinal (price not less than Rs.1600/each) with 5 litre PVC. automatic flushing cistern

od147448/2020_2021 : Supply and Installation of Counter Mount Kitchen sink , PVC Extension pipe and Flange, Standard waste coupling,wall chasing, refinishing etc.including the following :-

od147454/2020_2021 : Supply and Installation of site 15mm dia C.P brass Bib tap with wall flange including cutting and making good the wall wherever required(Jaquar ARI-39037/ equivalent)

od147463/2020_2021 : 6.Supply and Installation of 65mm Dia Butterfly valve including Wall cutting and making good in open terrace complete as required. (Supreme/Finolex/Astral or equivalent)

od147468/2020_2021 : Supply and Installation of 20mm Dia ss stop cock and allied including Wall cutting and making good in bathroom complete as required. (Jaquar Stopcock-Fus-29083k & Allied-Ald089/ equivalent)

od147475/2020_2021 : 9.Supply and Installation of 25mm Dia Brass valve including Wall cutting and making good in bathroom complete as required. (Supreme/Finolex/Astral or equivalent)

od147480/2020_2021 : Supply and Installation of 40mm Dia Brass valve including Wall cutting and making good in open terrace complete as required. (Supreme/Finolex/Astral or equivalent)

od147482/2020_2021 : 7.Supply and Installation of 50mm Dia Brass valve including Wall cutting and making good in open terrace complete as required. (Supreme/Finolex/Astral or equivalent)

od147489/2020_2021 : 1.Supply and Installation of Lead free PVC-U SWR pasted pipe using Solvent Cement ISI Marked [As per IS 4985] with Heavy duty ISI Marked PVC fittings.chasing the walls,floor,concrete etc. as required , replastering and refinishing using cement plaster 1:3 mix (cement:coarse sand ). Testing of the system for leakage and Air tightness (Supreme/Finolex/Astral or equivalent) - 50mm OD 6kg/sqcm Waste Piping

od147493/2020_2021 : Supply and Installation of Lead free PVC-U SWR pasted pipe using Solvent Cement ISI Marked [As per IS 4985] with Heavy duty ISI Marked PVC fittings.chasing the walls, floor, concrete etc. as required, replastering and refinishing using cement plaster 1:3 mix (cement:coarse sand). Testing of the system for leakage and Air tightness (Supreme/Finolex/Astral or equivalent) - 75mm OD Type-B Soil Piping

od147499/2020_2021 : 11.2.Supply and Installation of Lead free PVC-U SWR pasted pipe using Solvent Cement ISI Marked [As per IS 4985] with Heavy duty ISI Marked PVC fittings.chasing the walls, floor, concrete etc. as required, replastering and refinishing using cement plaster 1:3 mix (cement:coarse sand ). Testing of the system for leakage and Air tightness (Supreme/Finolex/Astral or equivalent) - 75mm OD Type-B Waste Piping

od147504/2020_2021 : 12.4.110mm OD 6kg/sqcm Rain Water Piping

od147509/2020_2021 : 12.3.Supply and Installation of Lead free PVC-U SWR pasted pipe using Solvent Cement ISI Marked [As per IS 4985] with Heavy duty ISI Marked PVC fittings. Ts, Elbows, Bends, Ys etc. Adapters, Air vents, Clamping with GI UClamps /supports, as required for firmliy installing the pipes and adjesent to the building/ chasing the walls, concrete etc. as required , replastering and refinishing using cement plaster 1:3 mix (cement:coarse sand ). Testing of the system for leakage and Air tightness (Supreme/Finolex/Astral or equivalent) - 110mm OD Air vent pipe

od147513/2020_2021 : 12.2. Supply and Installation of Lead free PVC-U SWR pasted pipe using Solvent Cement ISI Marked [As per IS 4985] with Heavy duty ISI Marked PVC fittings. Ts, Elbows, Bends, Ys etc.. Adapters, Air vents, Clamping with GI UClamps /supports, as required for firmliy installing the pipes and adjesent to the building/ chasing the walls, concrete etc. as required, replastering and refinishing using cement plaster 1:3 mix (cement:coarse sand). Testing of the system for leakage and Air tightness (Supreme/Finolex/Astral or equivalent) - 110mm OD Type-B waste Piping

od147517/2020_2021 : 12.1.Supply and Installation of Lead free PVC-U SWR pasted pipe using Solvent Cement ISI Marked [As per IS 4985] with Heavy duty ISI Marked PVC fittings. Ts, Elbows, Bends, Ys etc.. Adapters, Air vents, Clamping with GI UClamps /supports, as required for firmliy installing the pipes and adjesent to the building/ chasing the walls, concrete etc. as required, replastering and refinishing using cement plaster 1:3 mix (cement:coarse sand). Testing of the system for leakage and Air tightness (Supreme/Finolex/Astral or equivalent) - 110mm OD Type-B soil Piping

od147521/2020_2021 : Supply and Installation of Lead free UPVC SWR pasted pipe using Solvent Cement ISI Marked [As per IS 4985] with Heavy duty ISI Marked PVC fittings through trench having 60cm depth /as per site conditionand to make corresponding slope hence complete. [Excavation will be in the scope of contractor]. Testing of the system for leakage and Air tightness (Supreme/Finolex/Astral or equivalent) - 110mmOD Type-B soil piping

od147524/2020_2021 : Supply and Installation of Lead free UPVC SWR pasted pipe using Solvent Cement ISI Marked [As per IS 4985] with Heavy duty ISI Marked PVC fittings through trench having 60cm depth /as per site condition and to make corresponding slope hence complete.[Excavation will be in the scope of contractor]. Testing of the system for leakage and Air tightness (Supreme/Finolex/Astral or equivalent) - 160mmOD Type-B soil piping

od147527/2020_2021 : Supply and Installation of Lead free UPVC SWR pasted pipe using Solvent Cement ISI Marked [As per IS 4985] with Heavy duty ISI Marked PVC fittings through trench having 60cm depth /as per site conditionand to make corresponding slope hence complete.[Excavation will be in the scope of contractor]. Testing of the system for leakage and Air tightness (Supreme/Finolex/Astral or equivalent) - 200mmOD Type-B rain water piping

od147529/2020_2021 : Supply and Installation of 125x125mm CP Stainless Steel Gratings with Cockroach Protection for multi inlet floor trap.

od147531/2020_2021 : Multi Inlet floor trap 110x75x50mm.

od147533/2020_2021 : Supply and Installing at site Open UPVC Lead Free ASTM Schedule 40 Pipes (Equivalent Standard Size) with all accessories like bends, y's etc for Water supply Joined using Solvent Cement fittings suitable for the working pressure. Supporting exposed pipes using cement mortar at 60 cm intervals above terrace floor. Hydrostatic Testing of the Pipes using 10KG/cm2 test pressure for specified time period (Supreme/Finolex/Astral or equivalent) - 50mm Nominal Dia

od147535/2020_2021 : Supply and Installing at site Open UPVC Lead Free ASTM Schedule 40 Pipes (Equivalent Standard Size) with all accessories like bends, y's etc for Water supply Joined using Solvent Cement fittings suitable for the working pressure. Supporting exposed pipes using cement mortar at 60 cm intervals above terrace floor. Hydrostatic Testing of the Pipes using 10KG/cm2 test pressure for specified time period (Supreme/Finolex/Astral or equivalent) - 63mm Nominal Dia

od147537/2020_2021 : Supply and Installing at site Concealed UPVC ASTM Schedule 40 Pipes of Equivalent Standard Size with all accessories like bends, y's etc for Water supply Joined using Solvent Cement fittings with metal in-serts suitable for the working pressure. Chasing of the walls, concrete etc. as required, replastering and refinishing using Cement Plaster 1:3 mix [Cement : Coarse sand]. Hydrostatic Testing of the Pipes using 10kg/cm2 test pressure for specified time period (Supreme/Finolex/Astral or equivalent) - 25mm Nominal Dia

od147538/2020_2021 : Supply and Installing at site Concealed UPVC ASTM Schedule 40 Pipes of Equivalent Standard Size with all accessories like bends,y's etc for Water supply Joined using Solvent Cement fittings with metal in-serts suitable for the working pressure. Chasing of the walls, concrete etc. as required, replastering and refinishing using Cement Plaster 1:3 mix [Cement : Coarse sand]. Hydrostatic Testing of the Pipes using 10kg/cm2 test pressure for specified time period (Supreme/Finolex/Astral or equivalent) - 20mm Nominal Dia

od147540/2020_2021 : Supply and Installing at site Concealed UPVC ASTM Schedule 40 Pipes of Equivalent Standard Size with all accessories like bends, y's etc for Water supply Joined using Solvent Cement fittings with metal in-serts suitable for the working pressure. Through open walls, concrete etc. using GI clamps/supports as required, Hydrostatic Testing of the Pipes using 10kg/cm2 test pressure for specified time period (Supreme/Finolex/Astral or equivalent) - 50mm Nominal Dia

od147542/2020_2021 : Supply and Installing at site Concealed UPVC ASTM Schedule 40 Pipes of Equivalent Standard Size with all accessories like bends,y's etc for Water supply Joined using Solvent Cement fittings with metal in-serts suitable for the working pressure. Through open walls, concrete etc. using GI clamps/supports as required, Hydrostatic Testing of the Pipes using 10kg/cm2 test pressure for specified time period (Supreme/Finolex/Astral or equivalent) - 32mm Nominal Dia

od147543/2020_2021 : Supply and Installing at site Concealed UPVC ASTM Schedule 40 Pipes of Equivalent Standard Size with all accessories like bends,y's etc for Water supply Joined using Solvent Cement fittings with metal in-serts suitable for the working pressure. Through open walls, concrete etc. using GI clamps/supports as required, Hydrostatic Testing of the Pipes using 10kg/cm2 test pressure for specified time period (Supreme/Finolex/Astral or equivalent) - 25mm Nominal Dia

od147546/2020_2021 : Supply, Installing and Leveling Pipe Supports Fabricated from GI Slotted Rails / Channels of corresponding as per the site condition width suitable for carrying the operating weight of pipe and the fluids, 8mm Dia GI Adjustable Threaded Rods and Anchor Fasteners on wall, U clamps etc.as appropriate.

od147548/2020_2021 : Labour charges for core cutting of slabs/beam for pipes of following sizes - 110mm dia

od147550/2020_2021 : Labour charges for core cutting of slabs/beam for pipes of following sizes - 50mm dia

od147552/2020_2021 : Labour charges for core cutting of slabs/beam for pipes of following sizes - 40mm dia

od147553/2020_2021 : Labour charges for core cutting of slabs/beam for pipes of following sizes - 25mm dia

od147556/2020_2021 : Labour charges for core cutting of slabs/beam for pipes of following sizes - 75mm dia

od147557/2020_2021 : Supply and Installation of Towel Ring (Jaquar ACN-1121BN/ equivalent)

od147558/2020_2021 : Supply and Installation of Towel Rod (Jaquar ACN-1111NM/ equivalent)

od147559/2020_2021 : Supply and installation of rob hook (Jaquar AEC-CHR-1161/ equivalent)

od147560/2020_2021 : Supply and Installation of 40mm Non-returning valves (Supreme/Finolex/Astral or equivalent)

od147561/2020_2021 : Supply and Installation of 40mm Air releasing valve (Supreme/Finolex/Astral or equivalent)

od147562/2020_2021 : Supply and Installation of flow switch system for water level controling (sontay/system sensor)

od147563/2020_2021 : Supply and laying of 40mm nomial dia scheduled40 astm from well to tank (Supreme/Finolex/Astral or equivalent)

od147564/2020_2021 : Supply and Labour for installation of motor pump having minimum of 150 LPM discharge at 25m head including all required accessories like foot valve etc Make : 1.5HP crompton greaves/grundfos or equivalent

od147565/2020_2021 : Supply and installation of uPVC LH & RH 45° junction in ground having 600 mm base, 110mm dia inlet/outlet and 160 mm dia branch inlet with riser, heavy duty CI cover, frame and all accessories (Supreme or equivalent)

od147568/2020_2021 : Supply and installation of uPVC 90° / LH & RH 45° junction in ground having 315 mm base, 110mm dia inlet/outlet and 110 mm dia branch inlet with riser, heavy duty CI cover, frame and all accessories (Supreme or equivalent)

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed. All kinds of soil

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

od187229/2020_2021 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All work upto plinth level

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for: Foundations, footings, bases of columns, etc for mass concrete

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

od147459/2020_2021 : providing and fixing cast iron manhole cover including material and labour charges complete

od147465/2020_2021 : Providing glass for opening grill work

10.25.1 : Item Shifted to head 14 as item 14.74 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

10.25.2 : Item Shifted to head 14 as item 14.74 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

SEPTIC TANK and SOAK PIT

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed. All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

60.7.1 : DRY RUBBLE MASONRY _ Dry rubble without concrete levelling course masonry with good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

13.7.1 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 (1 cement : 3 fine sand)

23.5 : Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer -in- charges

23.6 : Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer -in-Charge

23.7 : Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge.

od147470/2020_2021 : Manhole using Cast iron 60x60cm size

Fire Estimation

od110248/2020_2021 : MS pipe 100 mm dia

od110253/2020_2021 : MS pipe 80 mm dia

od110254/2020_2021 : MS pipe 65 mm dia

od110258/2020_2021 : MS pipe 50 mm dia

od110264/2020_2021 : MS pipe 40 mm dia

od110266/2020_2021 : MS pipe 32 mm dia 1 m /31.1kg/m

od110300/2020_2021 : MS pipe 32 mm dia 1 m /2.41kg/m

od110353/2020_2021 : Under ground piping -100mm dia

od110377/2020_2021 : Hydraulic Hose Reel drum

od110452/2020_2021 : Ball valve

od110465/2020_2021 : GM Single Headed Hydrant Valve 63 mm dia

od110481/2020_2021 : Single Door Hose Cabinet

od110493/2020_2021 : GM Branch pipe, ISI marked 63 mm Female Instantaneous inlet

od110500/2020_2021 : Controlled Percolated Hose Conforming to IS: 636, 63 mm dia 15 mtrs.

od110532/2020_2021 : Single Acting Release valve with screwed inlet 20 mm dia

od110544/2020_2021 : Fire Brigade with inlet connection with 3 Nos of 63 mm dia.

od110551/2020_2021 : Electrically Driven Mono Block Terrace pump of capacity 900 LPM

od110560/2020_2021 : Electrically Driven Mono Block pump of capacity 2280 LPM

od110579/2020_2021 : Electrically Driven Mono Block pump of capacity 180 LPM

od110590/2020_2021 : Diesel operated Mono block pump of capacity 2280 LPM

od110726/2020_2021 : Pressure Gauge

od110732/2020_2021 : CI Butterfly valve slim seal standard lever operates type 100 mm dia

od110743/2020_2021 : CI Butterfly valve slim seal standard lever operates type 80 mm dia

od110750/2020_2021 : CI Non Return Valve slim seal type with required flanges

od110773/2020_2021 : Sprinkled heads designed to operate at 68 deg celcious ets

od110799/2020_2021 : Sign boards made out of 3 mm thick "Opaque" PVC foam board with computer cut

od110843/2020_2021 : Indoor type Exit board with LED Lamps reflector indicating arrows with exit recess mounted type

od110850/2020_2021 : Manuel call point break glass type

od110860/2020_2021 : Electronic dual tone Hooter

od110863/2020_2021 : Main Fire alarm control panel of 4 Zones capacity with visual Led indication for fire

od110869/2020_2021 : PVC conduit 20 mm dia

od110883/2020_2021 : 1 sq.mm Cross section PVC insulated copper wires

od110886/2020_2021 : Fire Extinguishers

ELECTRICAL ESTIMATE

90.12.7.12 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 3 core 4 sq mm with factory made clamp.

90.12.7.28 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 3.5 core 35 sq mm with factory made clamp

90.12.7.29 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 3.5 core 50 sq mm with factory made clamp

90.12.7.31 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 3.5 core 95 sq mm.

90.12.7.38 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 4 core 4 sq mm with factory made clamp

90.12.7.40 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 4 core 10 sq mm with factory made clamp

90.12.7.41 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 4 core 16 sq mm with factory made clamp

90.12.7.42 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 4 core 25 sq mm with factory made clamp

9.1.32 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

9.2.18 : Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 35 sq. mm

9.2.19 : Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 50 sq. mm

9.2.21 : Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 95 sq. mm

9.2.29 : Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm

9.2.30 : Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm

5.2 : Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. withcharcoal/ coke and salt as required

5.8 : Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earthelectrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

1.10.2 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group B

1.11 : Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

1.17.9 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.9 x 1.5 sq. mm

1.17.12 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

1.14.1 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

1.14.2 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.3 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

4.1.14 : Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.600 mm width X 75 mm depth X 2.0 mm thickness

4.2.13 : Supplying and installing following size of perforated pre-painted M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.900 mm width X 62.5 mm depth X 2.0 mm thickness

2.3.4 : Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator16 way, Double door

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.10.4 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

2.12.2 : Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.13.2 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.14.1 : Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 amps

1.31 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or inrecess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 ampsmodular switch, connection etc. as required. (For light plugs to be used in non residentialbuildings).

1.32 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

1.56 : Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlets and 2 Nos. 5/6 A modular switches, connection etc. as required. (For light plugs to be used in non residential buildings).

od115309/2020_2021 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (But without MCB/RCCB/Isolator), 6 way (4+18), Double door

od115357/2020_2021 : Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 4 way (4+12), Double door

od115886/2020_2021 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (But with out MCB/RCCB/Isolator), 4 way (4+12), Double door

2.15.3 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

od161561/2020_2021 : "MSB WITH METERING" Supply, Installation, Testing and commissioning of 125 A MV Cubicle panel board. front opening type, wall mounted free standing on 3" MS channel directly bolted to wall using nuts and bolts stenciling all identification etc.. confirming to IS1863, IE rules. Incomer 125A TP 36kA MCCB variable setting with inbuit EF release - 1 No. Class B&C Surge arrestor Type 1, Type 2 Outgoings 100A TP 25ka MCCB with all isolation duty and 3 Nos.125A cut out fuse unit and provision for CT net metering -1nos. 63A TPN 25ka MCCB with all isolation duty and 3 Nos.63A cut out fuse unit and provision for KWH meter-1nos. 63A 4P ACCL without Current limiter. All MCCBs are with rotary operating handle for door interlock. Busbar :125A TPN Al busbar

od161562/2020_2021 : "LCP Supply, Installation, Testing and commissioning of 40A MV Cubicle panel. Fabricated out of 16 swg CR CA sheet, powder coated dust and vermin tight proof, front opening type, flush and floor mounted free standing on 3" MS channel directly bolted to floor using nuts and bolts stenciling all identification etc.. confirming to IS1863, IE rules; INCOMER: 40A TPN MCB isolator - 1NOS; RYB Pilolet lamp - 1NOS; OUTGOING: 40A 4P 30MA RCCB - 1NOS; 25A DP 30MA RCCB with 4nos of 6A SP MCB - 1nos; Busbar: 40A TPN Al busbar"

od161564/2020_2021 : "SSB Supply, Installation, Testing and commissioning of 100A MV Cubicle panel. Fabricated out of 16 swg CR CA sheet, powder coated dust and vermin tight proof, front opening type, flush and floor mounted free standing on 3" MS channel directly bolted to floor using nuts and bolts stenciling all identification etc.. confirming to IS1863, IE rules; Incomer:100A TPN ISO - 1Nos.; 100A TPN ISO - 1Nos.; 100A 4P AC-1 Duty Contactor - 2Nos; RYB Piolet Lamps-2Set; Multifunction Meter-1No.; Outgoings 63A TP 18KA MCCB - 6 Nos; 40A TP 18KA MCCB - 3 Nos.; 80A TPN MCCB-1Nos [solar]; 63A 4P Isolator-1Nos; Electrical and mechanical interlocking shall be done. Microprocessor based AMF relay; All MCCBs are with rotary operating handle for door interlock. Busbar :100A TPN Al busbar"

2.15.2 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

1.25 : Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

1.24.1 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.4 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.6 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Telephone socket outlet

90.16.3.8 : Supply and clamping the following size of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 X 3 mm GI flat duly painted or heavy duty GI spacer saddles spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required (for horizontal run) 20 x 3 mm copper strip

90.16.4.7 : Supply and clamping the following sizes of strips on surface of wall / parapet/ existing cable tray using clamps fabricated from 20 x3 mm GI flat duly painted or heavy duty GI spacer saddles, spacing of clamps not exceeding 1 m , making good the damages, colour washing etc. as required (for vertical run). 20 x 3 mm copper strip

90.16.1.5 : Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required. 75mm copper conductor (6 SWG)

od162126/2020_2021 : Supply and Fixing of laminated schematic drawings.

od162127/2020_2021 : Supply and Fixing of 2Nos. 9 litres red colour fire bucket on stands

od162128/2020_2021 : Supply and Fixing of 5kg dry powder fire extinguishers on clamp.

od162129/2020_2021 : supply and fixing of 440 V grade synthetic insulated mat 2 meter x 1 meter x 6mm conforming to IS:15652:2006

od162130/2020_2021 : Supply and fixing of shock treatment chart in glass with frame

od162131/2020_2021 : Supply and fixing of LT danger boards

od162274/2020_2021 : "GSB; Supply, Installation, Testing and commissioning of 125A MV Cubicle panel. Fabricated out of 16 swg CR CA sheet, powder coated dust and vermin tight proof, front opening type, flush and floor mounted free standing on 3" MS channel directly bolted to floor using nuts and bolts stenciling all identification etc.. confirming to IS1863, IE rules; Incomer 125A TPN isolator - 1nos; RYB piolet lamp - 1nos; Reverse Power Relay 415V AC -1nos; Outgoing100A TPN 25KA MCCB - 1 nos; 63A TPN 25KA MCCB -1No; All MCCBs are with rotary operating handle for door interlock; Busbar:125A TPN Al busbar

1.27.1 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

od162345/2020_2021 : Supply and fixing of DOL starter for 1.5Hp in open enclosure with required capacitor with on/off push button

od162346/2020_2021 : Supply and installation of IP-65 junction box suitable for connecting 3x2.5 sqmm cu cable

od162347/2020_2021 : Supply and installation of 63A 4P cubical isolator with open enclosure IP based<br>

od162348/2020_2021 : Supply and Installation of V25 B+C/3+NPE 320V

od162349/2020_2021 : Supply and installation of RJ 45 socket With Shutter

14.4 : Excavation for cable trenches in soft soil, depth upto 1.2 m including dressing of sides lift upto 1.5 m, including getting out the excavated soil, refilling with sand and or good soil after laying of cable/ pipe etc in layers of 20 cm, ramming, watering and disposal of surplus excavated soil as directed, within a lead of 50 metres.

14.9 : Providing and laying in position cement concrete 1 :3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) in foundation of pump, DG set etc. including form work etc. as required.

14.11 : Providing brick work (in width 225 mm or more) with F.P.S. bricks of class designation 7.5 in cement mortar 1:4 (1 cement : 4 coarse sand) at all levels.

od162549/2020_2021 : Supply and labour charges for Fixing of 40W post top light with 3mtr pole

od162550/2020_2021 : Supply and labour charges for Fixing of 20w tube light 1200mm

od162551/2020_2021 : Supply and labour charges for Fixing of Mirror Light 10W 2feet battern light

od162552/2020_2021 : Supply and labour charges for Fixing of Ceiling exhaust fan 28w ceiling mounting white vent air sweep 130 mm

od162553/2020_2021 : Supply and labour charges for Fixing of Wall Fan 60W 450mm sweep

od162554/2020_2021 : Supply and labour charges for Fixing of Wall Exhaust Fan 9 Inch

od162555/2020_2021 : Supply and labour charges for Fixing of Ceiling fan 1200 mm

od162556/2020_2021 : Supply and labour charges for Fixing of 9w Square LED Panel Ceiling Light

od162557/2020_2021 : Supply and labour charges for Fixing of 12W Round LED Panel Ceiling Light

od162558/2020_2021 : Supply and labour charges for Fixing of 18w Round LED Panel Ceiling Light

od162559/2020_2021 : Supply and labour charges for Fixing of 6W Round LED Panel Ceiling Light

od162561/2020_2021 : Supply and labour charges for Fixing of 18W Exterior Wall light - Bulk Head

od162562/2020_2021 : Supply and labour charges for Fixing of 12w Wall light(wall washer)

6.3 : Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required.

od162574/2020_2021 : Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, copper tube,having single prong at top, with 85 mm dia 3 mm thick copper base plate including holes etc.complete as required.

od162662/2020_2021 : Preparation of necessary drawing and getting all necessary approvals/sanction, inspection,supervision charges etc.from EI/EB including all sundries expenses except statutory charges. Statutory charges shall be reimbursed only after producing valid proof

od162663/2020_2021 : Supply and labour charges for Fixing of 12W T bulb with holder

8.3.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 120 sq. mm and upto 400 sq. mm

10.5.4 : Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :300 sq. mm

od190007/2020_2021 : Supply of following 11 KV XLPE UG cable in existing open trench/ open tray 3cx300sq mm

AC ESTIMATE

od116004/2020_2021 : Supply, Installation, Testing & Commissioining of Armoured control cum transmission wiring between ODU & IDU of required size with pvc conduit and other accessories as per specification and relavent standards, and all other electrical connections from isolator to the units

od116043/2020_2021 : Condensate Piping Supply and erection of the condensate UPVC pipes with all joints, reducers, necessary elbows and tees, supporting arrangements etc. Rate shall inclusive of thermal insulation with 13mm thickness FM approved closed cell nitrile rubber insulation covering with fire resistant fibre cloth fabric as a resistant to scracth and mechanical impacts 25mm Dia UPVC

od116051/2020_2021 : Supply and labour for installation of Refnut Y joints

od116146/2020_2021 : Supply and labour for Refrigerant gas charging R410 gas

od116305/2020_2021 : "Refrigerant Piping- Supply and errection of 16gauge hard drawn refrigerant copper pipe to integrate out door/ indoor units. The rate shall inclusive of closed cell nitrile rubber insulation for copper pipes and fiber glass cloth covering. The FRP/poly shield coating shall be applied over the insulation for exposed application. Pipe size and insulation thickness as follows" 9.5mm with 6.35mm thick insulation

od116312/2020_2021 : "Refrigerant Piping- Supply and errection of 16gauge hard drawn refrigerant copper pipe to integrate out door/ indoor units. The rate shall inclusive of closed cell nitrile rubber insulation for copper pipes and fiber glass cloth covering. The FRP/poly shield coating shall be applied over the insulation for exposed application. Pipe size and insulation thickness as follows" 12.7 mm with 6.35 mm thick insulation

od116329/2020_2021 : "Refrigerant Piping- Supply and errection of 16gauge hard drawn refrigerant copper pipe to integrate out door/ indoor units. The rate shall inclusive of closed cell nitrile rubber insulation for copper pipes and fiber glass cloth covering. The FRP/poly shield coating shall be applied over the insulation for exposed application. Pipe size and insulation thickness as follows" 15.9mm with 9.5mm thick insulation

od116342/2020_2021 : "Refrigerant Piping- Supply and errection of 16gauge hard drawn refrigerant copper pipe to integrate out door/ indoor units. The rate shall inclusive of closed cell nitrile rubber insulation for copper pipes and fiber glass cloth covering. The FRP/poly shield coating shall be applied over the insulation for exposed application. Pipe size and insulation thickness as follows" 19.1mm with 9.5 mm thick insulation

od116374/2020_2021 : "Refrigerant Piping- Supply and errection of 16gauge hard drawn refrigerant copper pipe to integrate out door/ indoor units. The rate shall inclusive of closed cell nitrile rubber insulation for copper pipes and fiber glass cloth covering. The FRP/poly shield coating shall be applied over the insulation for exposed application. Pipe size and insulation thickness as follows" 28.6 mm with 12.7 mm thick insulation

od116379/2020_2021 : "Refrigerant Piping - Supply and errection of 16gauge hard drawn refrigerant copper pipe to integrate out door/ indoor units. The rate shall inclusive of closed cell nitrile rubber insulation for copper pipes and fiber glass cloth covering. The FRP/poly shield coating shall be applied over the insulation for exposed application. Pipe size and insulation thickness as follows" 22.2 mm with 9.5 mm thick insulation

od116384/2020_2021 : "OUT DOOR UNITS Supply, Installation, testing and commissioning of out door units consist of 100% inverter scroll compressor/twin rotary compressors, Dc fan Motor with aero-spiral fan blade, e-pass heat exchangers, safety valves, solenoid valves, receiver, capillary tubes, check valve, electronic expansion valve, High pressure switch, low pressure sensor, pressure regulating valve, refrigerant filter, stop valve, accumulator and refnet kits. Rate inclusive of R-410A refrigerant and oil pre charging, power cable from nearest isolator, vibration isolators, supports, necessary foundation/ pedestal works etc..(High COP Models)" 14HP

od116389/2020_2021 : "INDOOR UNITS Design, Supply, Installation, testing and Commissioning of VRF indoor air conditioning units with direct driven fan, high efficient filter, Inbulit micro controller thermostat, electronic expansion valve, Remote controller including cables, neccessory supports and vibratrion isolators, Refrigerant charging, refnet joints for both liquid and gas lines branch kits, control wiring, power cables form nearest socket including plug, drain connections etc.. Capacities as mensioned below" FOUR-WAY CASSETTE AC(VRF) a) Cooling capacity-3TR

od116392/2020_2021 : "INDOOR UNITS Design, Supply, Installation, testing and Commissioning of VRF indoor air conditioning units with direct driven fan, high efficient filter, Inbulit micro controller thermostat, electronic expansion valve, Remote controller including cables, neccessory supports and vibratrion isolators, Refrigerant charging, refnet joints for both liquid and gas lines branch kits, control wiring, power cables form nearest socket including plug, drain connections etc.. Capacities as mensioned below" HI-WALL SPLIT AC(VRF) d) Cooling capacity-0.8TR

od116445/2020_2021 : "INDOOR UNITS Design, Supply, Installation, testing and Commissioning of VRF indoor air conditioning units with direct driven fan, high efficient filter, Inbulit micro controller thermostat, electronic expansion valve, Remote controller including cables, neccessory supports and vibratrion isolators, Refrigerant charging, refnet joints for both liquid and gas lines branch kits, control wiring, power cables form nearest socket including plug, drain connections etc.. Capacities as mensioned below" HI-WALL SPLIT AC(VRF) c) Cooling capacity-1.5TR

od116450/2020_2021 : "INDOOR UNITS Design, Supply, Installation, testing and Commissioning of VRF indoor air conditioning units with direct driven fan, high efficient filter, Inbulit micro controller thermostat, electronic expansion valve, Remote controller including cables, neccessory supports and vibratrion isolators, Refrigerant charging, refnet joints for both liquid and gas lines branch kits, control wiring, power cables form nearest socket including plug, drain connections etc.. Capacities as mensioned below" HI-WALL SPLIT AC(VRF) b)Cooling capacity-2TR

od116452/2020_2021 : "INDOOR UNITS Design, Supply, Installation, testing and Commissioning of VRF indoor air conditioning units with direct driven fan, high efficient filter, Inbulit micro controller thermostat, electronic expansion valve, Remote controller including cables, neccessory supports and vibratrion isolators, Refrigerant charging, refnet joints for both liquid and gas lines branch kits, control wiring, power cables form nearest socket including plug, drain connections etc.. Capacities as mensioned below" HI-WALL SPLIT AC(VRF) a) Cooling capacity-2.5TR

DIESEL GENERATOR

od162195/2020_2021 : Supply and Labour charges for erection of additional length of MS[B class medium grade]exhaust pipe line of suitable sizes, with heat resistant Al painting to building top for 82.5 KVA DG.

od162196/2020_2021 : "Diesel generator; Supply and Labour for Installation, testing & commissioning of 3 phase 82.5 KVA Diesel generator, including required earthing, power/control cabling, terminations including getting the necessary clearance/approval of generator from electrical inspectorate, testing of neutral CT, relays, meters etc.. as required[statutory charges shall be borne by the clients on production of valid proof][ Mechanical erection of packaged generator will be done by the generator supplier]"

od162234/2020_2021 : "UPS; Supply and Labour for installation of 3 phase in single phase out 20kVA UPS with battery bank SMF type having 20 minutes back up"

One lift passenger MRL 8 passenger 544 kgs of V3f Gearless with Automatic centre opening doors in stainless steel hairline finish upto 5 stops without machine room

Bidder Name

A.M.MOHAMMED ALI