Loading…
Loading…
Tender Value
₹77.6 L
EMD Value
₹77,600
Closing Date
16 Jun 2026, 6:00 pm
The Chief Officer, Padra Municipality, Padra
BID DOCUMENTS FOR CONSTUCTION WORK OF COMPOUND WALL, PUMP ROOM , LIGHT,BORE AND R.C.C PIPE DRAIN IN COW SHED AT SAREJA OF PADRA NAGARPALIKA UNDER: 15 TH FINANCE SCHEME.
308924
15 TH FINANCE SCHEME
Open
Civil - All
Vadodara
12 documents required · 12 mandatory
₹2,832
The Chief Officer, Padra Municipality, Padra
₹77,600
27 May 2026
27 May 2026
27 May 2026
16 Jun 2026
27 May 2026
3 PROVIDING AND LAYING OF 600 MM DIA R.C.C. NP3 PIPE ( TWO Rs.
ROW ) STROM WATER DRAIN PATDIYA HANUMAN TEMPLE AT PADRA.
4 DRILLING OF 165MM DIA X 90 MTS. DEEP DTH BORE WITH PROVIDING & Rs.
INSTALLATION OF SINGLE PHASE SUB. PUMP SET AT MRF SHED AT
I / We am/are willing to carry out the work at _____________ % above / below (percent should be written in figure and in
words) of the estimated rates mentioned above. Amount of my/our tender works out as under.
( In words ) _________________________ percentage above / below the estimated rate.
Estimated Amount put to tender Rs.
Deduct _______ % below Rs. Rs.
Estimated Amount put to tender Rs.
Add _______ % above Rs. Rs.
Total Amount Rs.
Total Amount Rs.
*( Please strike out whichever is not applicable)
Note :1 All work shall be carried out as per Public Works Department Hand Book and other specifications of Division or as
Note :2 Rates quoted include clearance of site (prior commencement of work and its close) in all respects and hold good
for work under.
Note : 3 I/ We have read the conditions mentioned in this tender and agree to abide by the same.
Note : 4 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-
10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where
there is a change as per actual mix design the cost of difference of cement consumption have been deducted
from the rate of original item at the rate of input rate mentioned in all the tender.
Signature of Contractor President Chief Officer
Padra Nagarpalika Padra Nagarpalika
SECTION-7 BILL OF QUANTITIES-298
PADRA MUNICIPALITY, PADRA
PROPOSED REMAINING COMPOUND WALL FOR COW AT ,SAREJA PADRA.
Qty. Description Unit Amount
1 30.00 Boring holes 3.5 m deep in ordinary soil (for cast in situ piles) and
Each getting out the soil and disposal of the surplus excavated soil as
directed within a lead of 50 Meter for following diameter of pipes.(iii)
350 mm 1523.30 Each
2 30.00 Add to or deduct from the rate for Bore Holes of 3.5 m Depth, if bore
Each holes are made deeper or shallower than 3.5M. for Piles of following
diameter.(iii) 350 mm
3 30.90 Excavation for Foundation upto 1.5 m. Depth including sorting out and
Cmt. stacking of useful materials and disposing of excavated stuff upto
Meter lead (A) (loose or soft soil) 120.01 Cmt.
4 11.45 Filling available excavated earth (excluding Rock) in trenches. Plinth,
Cmt. sides of foundations etc. in layers not exceeding 20cm. In depth
consolidating each disposited layer by ramming and watering. 133.65 Cmt.
5 8.50 Providing and laying cement concrete 1:4:8(1 Cement, 4 coarse sand,
Cmt. graded stone aggregates 20mm nominal size) and curing complete
excluding cost of formwork in Foundation and Plinth
6 41.25 Providing and Laying controlled cement concrete M-250 and curing
Cmt. complete, including the cost of formwork and reinforcement for
reinforced concrete work in Column footings. 4707.61 Cmt.
7 10.95 Providing and Laying controlled cement concrete M-250 and curing
Cmt. complete, including the cost of formwork and reinforcement for
reinforced concrete work in Columns(Padestal)
8 7.35 Providing and Laying controlled cement concrete M-200 and curing
Cmt. complete, including the cost of formwork and reinforcement for
reinforced concrete work in Columns
9 11.55 Providing and Laying controlled cement concrete M-250 and curing
Cmt. complete, including the cost of formwork and reinforcement for
reinforced concrete work in Ground Beam
SBD SECTION-7 BILL OF QUANTITIES-299
10 2.05 Providing and Laying controlled cement concrete M-200 and curing
Cmt. complete, including the cost of formwork and reinforcement for
reinforced concrete work in Coping 6218.57 Cmt.
6142.00 Providing TMT Bar FE 500D reinforcement for R.C.C. work including
Kgs. bending, binding and placing in position complete upto floor two level
12 22.60 Providing and Laying Brick work using common burnt clay building
Cmt. bricks (Conventional) having crushing strength not less than 35 Kg./Sq.
Cm. in Super Structure Above Plinth level in Cement Mortar (1:6) (1
Cement : 6 fine sand) etc. complete for any Height.
13 221.10 Providing and laying 15mm thick cement plaster in single coat Rough
Smt. (Similar) side of single or Half brick walls for interior plastering upto
floor two level and finished even smooth in (i) C.M. (1 : 4) (1 -Cement :
-sand ) including neat Cement slury finishing scaffolding, curing etc.
complete. 220.61 Smt.
14 221.10 Finishing wall with Weather Proof Acrylic Exterior Emulsion Paint on
Smt. wall surface (two coats) to give and required shape even shade and of
approved brand and manufacturer after throughly brushing the surface
to remove all dirts, and remians of loose powdered materials etc.
complete. 114.53 Smt.
15 20.06 Providing and fixing M.S. grills of required pattern to wooden frames of 9108.48 Qtl
Qtl. window etc. with M.S plate at required spacing & frame alround,squre
or round bar with rounded headed bolts & nuts or by screws.Providing
and fixing M.S Angle (50X50X6)
Providing and Fixing Chain Link 2 10 x 10 guage (Galvanised)
Smt. 256.78 Smt.
17 355.50 Painting two coats of paint (including one priming coat ) on new steel &
Smt other metal surfaces with sythetic enamel paint brushing interior to
give an even shade including cleaning the surface of all dirt , dust &
other foreign matter.
18 586.15 Filling in foundation and plinth with murrum or selected soil in layers of
Cmt 20cm thickness including watering, ramming and consolidating etc.
complete. 296.29 Cmt
SBD SECTION-7 BILL OF QUANTITIES-300
PADRA MUNICIPALITY, PADRA
ESTIMATE FOR PROVIDING & FIXING LIGHTS AND FIXTURES AT COW SHED COMPOUND WALL AT SAREJA AT
Quantity Unit Discription Unit Amount
1 270.00 Rmt. Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper
cable 1.1 KV grade to be erected as directed of following size.
(A) 2 Core 2.5 sq. mm 101.00 Rmt.
2 1.00 Ea. Approved make Four pole moulded case circuit breaker having
breaking capacity ICU of 25 KA. at 415 V,having normal current
rating up to 25 A to 100A. with Fixed thermal & magnetic release
suitable to work on A.C. supply 50 c/s. with all internal connections
& complete erected in existing 16 G.M.S. housing. Cat-ll
3 3.00 Each Providing and erecting Approved make RCCBs conforming to IS:
12640 and having sensitivity of 30 mA and Short Circuit withstand
capacity of 10 KA and suitable for operation on 3 phase and neutral
415V,50Hz. having characteristic of quick action & tripping with all
advance feature & do not incorporate any electronic component for
following Max. rating erected as directed.
(iii) 63 Amps. FP Cat. III 3040.10 Each
4 30.00 Ea. providing and erecting Miniature circuit breaker single pole 0.5A to
2A system and having breaking capacity 10 KA to be erected in
existing box. confirming to IS 8828/1996 with ISI Mark
Cat.III 270.68 Ea.
5 9.00 Kg Providing and erecting Annealed bare Copper wire 8 to 16 SWG.
6 30.00 Ea. Providing and erecting Pipe type earthing having 150 cms.long and
2.5 cms. dia. galvanised iron pipe with coupling and buch buried in
specially prepared earth pit complete with necessary 8 SWG earth
wire. 368.65 Ea.
SBD SECTION-7 BILL OF QUANTITIES-301
7 1.00 Ea. Supplying & erecting funnel type earthing having earth plate of
following size burred in specifically prepared earth pit 3 mtr.
below ground with 40 kg. charcoal and salt with alternate layers of
charcoal & salt, 20mm.dia. G.I. pipe with Funnel with a wire mesh
for watering & bricks masonry block, C.I. Cover complete as per para
7.3 of IS 3043 with necessary length of double Galvanised Iron /
copper earth wire No 6 SWG bolted with lug to the plate and
covered in 12 mm dia. G.I. pipe 2.5 mtr long complete connected to
the nearest switch gear with end socket as per direction & duly
tested by earth tester confirming to IS (As per drawing) with
following specification 7874.97 Ea.
(C) with 60 x 60x 0.315 cms. Copper earth Plate
8 30.00 Ea. For using salt and charcoal / coke as required for pipe type earthing.
9 600.00 Mtr Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable
multistrand / Solid Aluminium conductor for 1.1 KV. to be laid on
wall with necessary clamps or in existing trench / pipe of following
size of cables (C) 4 core 10 Sq. mm 140.39 Mtr.
10 550.00 Mtr. Providing & laying approved make Double walled corrugated pipes
(DWC) of polyethylene(conforming to IS 14930 II )with necessary
connecting accessories of same material at required depth in
existing trench for laying of cable. below ground / road surface for
enclosing cable (A)50 mm outer dia 62.62 Mtr.
11 120.00 Ea. Providing and, fixing heavy duty flange type brass cable gland with
rubber ring for PVC insulated armoured cable complete with out
going tails, insulating tape etc for following size of cables.
(C) 2 to 4 core 10 Sq. mm 38.38 Ea.
12 30.00 Ea. Supplying and erecting approved make Conical Pole (Standard )
Made from HR sheet steel. The pole should be made as per IS. and
shall be coated with hot dip galvanizing as per IS 2629/2633/4759
with required base plate and integral Junction box consist of
terminal plate of min 6mm Hylam sheet, standard profile
35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and
arrangement for cable terminationas erected on suitable foundation
(included) with necessary GI nut-bolts/J-Bolts. as per details given
by manufacturer considering site requirement.The length of poles
are as below (B) 4 Mtr. Long 65mm Top X125 mm bottom dia, 3mm
SBD SECTION-7 BILL OF QUANTITIES-302
13 30.00 Ea. Supplying and erecting Street light pole bracket comprising main B
Class GI pipe of 4.2 cm/require outside dia. complete with suitable B
Class G.I. sleeve tubing of approx. 45cms.length and suitable for
76.5mm/80mm/require size of pole top having nuts and bolts for
fixing the brackets and having spread of 0.5 mtr. Length with
deg.with vertical plane and suitable welded stiffener reducer and
nipple with check nut complete painted with one coat.of Red oxide /
PU base primer and two coats of Aluminium / PU paint. paint with
following nos of arms. [A] Single Arm bracket 1 Mtr
14 30.00 Each Supplying and erecting LED street light / Flood light fittings with High
power White LEDs wattage of 3 Watt and above assembled on single
MCPCB, efficiency more than 130 lm/w and corrosion free High
pressure die cast aluminium housing with smooth finish powder
coated and heat sink extruded aluminium with diffuser and
Polycarbonate optics/ lenses with company mark/name engraved or
embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %,
CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy>
100 lumens/watt . LED driver efficiency > 85 %.( fittings required
LM-79 & LM-80 certificates)(NOTE: Below description have shown
ranges of Wattage capacity of LED fittings.The Engineer incharge
may select any wattage capacity between the ranges shown.) (A)
Street Light (IP-65), Surge protection -4KV integral and ,Light must
have 440VAC line supply with over-voltage protection. (ii) above
to 60 Watts CAT-III
15 1.00 Ea Supplying & erecting power contactor ,AC3 duty for time switch
complete erected as per direction Cat III
(B)2 pole 250 V 32 Amp
16 1.00 Nos. Supplying & erecting approved make Digital time switch having
lithium cell 6 years operative and operate battery backup 1 channel
day clock with 14 memory programme, suitable to operate on 240V
+ 5%, 16A with, floating contacts Minimum switching setup time
minimum & LCD display. Also comprised permanent ON/OFF
switching. Programming switches & housed in fire proof
thermoplastic enclosure & transparent cover erected as required
with necessary connection erected as directed.
SBD SECTION-7 BILL OF QUANTITIES-303
14 1.00 No. Supplying & erecting IP 55 grade following size section pillar
fabricated from joint less M.S. Sheet with angle iron legs made from
jointless M.S. Angle with cable clamps to be buried in ground to
have appropriate erection to work uniform until erected with
cement concrete foundation and 45 cm high bricks work finishing
with plaster etc. hinged double door internally supported on both
side, with internal and outside looking arrangement with look and
keys in duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos. one is
welded and other with nut and bolt for erecting Bakelite sheet.
Painting the Section Pillar inside and out side with three tank
powder coated paint. section pillar roof should be without joint
with water leakage proof & tested as per IP 55 test & followed by IS
2147 of 1962 (B) 75 X 60 X 45 cm section pillar fabricated from
Gauge MS Sheet with angle iron legs 45 cm long made from 35 X
X 5 mm thick MS angle.
SBD SECTION-7 BILL OF QUANTITIES-304
PADRA MUNICIPALITY PADRA
ESTIMATE FOR PROPOSED PUMP ROOM AT COW SHED SITE AT SAREJA ,PADRA
Item Qty. Total
No. Rate Unit Amount
1 25.00 Excavation for foundation upto depth 1.5 m.Depth including sorting
out and stacking of useful material and disposing off the
excavated stuff upto 50 m lead (loose or soft soil) 120.01 Cmt.
2 12.00 Excavation for foundation for depth 1.5 m. to 3.0 m including
sorting out and stacking of useful material and disposing off the
excavated stuff upto 50 m lead (loose or soft soil) 133.05 Cmt.
3 27.00 Filling available excavated earth (excluding rock) in trenches plinth,
sides of foundations etc. in layers not exceeding 20 cm in depth
consolidating each deposited layer by ramming and watering.
4 8.00 Filling in foundation and plinth with murrum or selected soil in
layers of 20cm thickness including watering, ramming and
consolidating etc. complete. 296.29 Cmt.
5 9.00 Applying General insecticide pest control treatment to floors, cup
boards etc. including labour material etc. complete. Using
Heptachloride 20 EC. As per 6113_pests constructions weight
percent is recommended one litre chemical emulsion dillute with
liter of water will give. total dillute concentration will be 40 litre
inclusive of one litre chemical emulsion application 0.5 litre
chemical/ sqm of surface is recommended as per IS.
6 4.50 Providing and laying cement concrete 1:3:6 (1 Cement, 3 coarse
sand, 6 hand broken stone aggregates 40mm. Nominal size) and
curing ecomplete excluding cost of formwork in (A) Foundation and
Plinth.( More then 10 ton) 3084.94 Cmt.
7 Providing and laying controlled cement concrete M-250 and curing
complete Including the cost of formwork But Excluding cost of
reinforcement of reinforced concrete work in
a. 4.00 -- do -- for R.C.C. Column Footing 4738.92 Cmt.
b. 2.00 -- do -- for R.C.C. Column upto PL 7233.62 Cmt.
c. 1.50 -- do -- for R.C.C. Column Super Structure 8559.75 Cmt.
d 2.00 -- do -- for Ground Beam 5730.74 Cmt.
SBD SECTION-7 BILL OF QUANTITIES-305
Item Qty. Total
No. Rate Unit Amount
8 Providing and laying controlled cement concrete M-200 and curing
complete Including the cost of formwork But Excluding cost of
reinforcement of reinforced concrete work in
a 1.00 -- do -- for RCC Flooring 5379.26 Cmt.
a 0.50 -- do -- for Coping 5379.26 Cmt.
b 1.00 -- do -- for R.C.C. Lintel 6066.06 Cmt.
c 1.00 -- do -- for R.C.C. Chajja 4820.73 Cmt.
d 1.50 -- do -- for R.C.C. Beam 5666.10 Cmt.
e 2.50 -- do -- for R.C.C. Slab 4594.49 Cmt.
9 1480.00 Providing TMT Bar FE 500D reinforcement for R.C.C. work
includingbending, binding and placing in position complete upto
floor two level 77.29 Kg.
10 4.00 Brick work using common burnt clay building bricks having
crushing strngth not less than 35 Kg./cm2 in C.M. foundation and
plinth (1:6) (1 Cement, 6 fine sand) (B)Conventional racking out
joints curring etc. complete directed by Engineer-in-charge. (
more than ten ton ) 4121.55 Cmt.
11 10.00 Brick work using common burnt building bricks having crushing
strngth not less than 35 Kg./cm2 in super structure for Ground
Floor in C.M. (1:6) (1 Cement, 6 fine sand) (B)Conventiona racking
out joints curring etc. complete directed by Engineer-in-charge.
12 4.00 Providing and Fixing Rolling Shutters of approved make made of
80 mm wide M.S. laths inter-locked together through their entire
length and jointed together at the ends by end locks mounted on
specially designed pipe shaft with bracket plates, guide channels
and arrangements for inside and outside locking with push-pull
operation including the cost of hood cover and spring etc. complete
(B) Shutter having width below 3.5 m
13 3.00 Providing and Fixing 35mm thick shutters for doors, windows and
clearestorey window including indian teak wood frames 10cm x
cm size including black enamelled iron oxidised fixtures and
fastening including primer coat of approved quality and two cost of
oil painting etc. complete 5533.68 Smt.
SBD SECTION-7 BILL OF QUANTITIES-306
Item Qty. Total
No. Rate Unit Amount
14 1.00 Providing and fixing glazed louverd glass windows and ventilators
with teakwood frame 10cm x 7cm size including the cost of oil
painting to wood work etc. complete.(up to 10 Ton) 4202.12 Smt.
15 Providing and fixing M. S. grills of requried pattern to wooden
frames of window etc. with M. S. flats at requried spacings and
frame alround square or round bars with round headed bolts and
nuts or by screws.
(A) 270.00 Plain Grill 141.51 Kg.
16 18.00 Painting two coats (Including Priming Coat) on new steel and other
metal surfaces with synthetic enamel paint brushing,interior to
give enamel paint brushing, interior to give an even shade
including cleaning the surface an even shade including cleaning
the shurface of all dirt, dust and other foreign matter.
17 137.50 Providing and laying 15mm thick cement plaster in single coat
Rough (Similar) side of single or Half brick walls for interior
plastering upto floor two level and finished even smooth in (i) C.M.
(1 : 4) (1 -Cement : 4 -sand ) including neat Cement slury finishing
scaffolding, curing etc. complete. 220.61 Smt.
18 9.00 Providing and laying 10mm thick cement plaster in Single coat on
brick/concrete walls for plastering on ceiling and soffits of stairs
upto floor two level and finished even smooth in (i) C.M. (1 : 4) (1 -
Cement : 4 -sand ) including neat Cement slury finishing
scaffolding, curing etc. complete. 218.50 Smt.
19 146.50 Applying two coats of Birla (white cement based) or Asian (acrylic
lapy-putty)or equivalent & two coats of primer of approved brand
and manufacture on new wall surface to give an even shade
including thoroughly brushing the surface from mortar dropping
and other foreign matter and sand papered smooth
20 137.50 Distempering (Three Coat) with oil bound washable distemper of
approved brand and manufacture and of required shade on wall
surfaces to give and even shade over and including a primer coat
with alkali resistance primer of approved brand after throughly
brushing the surface free from other foreign matter and also
including preparing the surface even and sand papered smooth.
21 9.00 Distempering (Three Coat) with oil bound washable distemper of
approved brand and manufacture and of required shade on Ceiling
& Sloping Roof surfaces to give and even shade over and including
a primer coat with alkali resistance primer of approved brand after
throughly brushing the surface to give and free from other foreign
matter and also including preparing the surface even and sand
papered smooth. 109.92 Smt.
SBD SECTION-7 BILL OF QUANTITIES-307
Item Qty. Total
No. Rate Unit Amount
22 103.00 Finishing wall with Weather Proof Acrylic Emulsion Exterior Paint
on wall surface (two coat) to give and even shade and of approved
brand and manufacture including throughly brooming and brushing
the surface to remove all dirts, and remians of loose powdered
material. 117.40 Smt.
23 23.50 Providing and laying cement concrete flooring 1:2:4 (1 cement :
corase sand :4 graded stone aggregate 20 mm nominal size) laid
in one layer finished with floating coat of neat cement. 50mm thick
(Upto10 ton) 339.15 Smt.
24 2.00 Providing and fixing in position cowel went to pipes.(B) 75mm dia.
25 2.00 Providing and fixing M.S. Fan clamps type 1 to 16mm dia M.S. bar
bent to shape with hooked ends to R.C.C. slab curing, laying
including painting the exposed portion of loops, all as per standard
design complete. 131.93 No
26 5.30 Purchasing & supplying at site of works with railway freight,
loading, unloading, carting etc. complete such as joints, channels,
angle irons, rails etc. complete.
M.S. Rails 200 x 100 x 6 mm size 2979.50 R.M.T.
27 0.20 Labour charges for lowering, laying, fixing various size of M.S.
sections such asjoints, channels, angles, plates etc. complete
M.S. Rails 200 x 100 x 6 mm size 11478.65 M.T.
28 9.00 Providing and Laying broken China Mosaic Flooring for terrace
using 12 mm to 20 mm broken pieces of glazed tiles to be laid over
cement mortar 1:3 to plain slope and to be tempered to bring
mortar crème out upto surface using white cement including
rounding off junctions and extending them up to 15 cm along the
wall clearing with water and oxalic acid etc. as directed.
SBD SECTION-7 BILL OF QUANTITIES-308
Item Qty. Total
No. Rate Unit Amount
29 5.60 Providing, Supplying, Lowering and laying standard length ISI mark
rigid unplasticed PVC pipes and specials of following class and
diameter suitable for portable water with ringfit joint including cost
of rings as per IS specification no. 4985/1998 including cost of
labour, material, except cement solvent and all local and central
taxes, transportation, freight charges, octroi, inspection charges,
loading, unloading, conveyance to the departmental stores and
including cost of jointing material and giving satisfactory hydraulic
testing as per ISI code etc. complete.
100 MM Dia 6.0 Kg/Cm2
SBD SECTION-7 BILL OF QUANTITIES-309
Padra Municipality padra
Project Name: Estimate For Providing Electrification Installation in Proposed Pump Room At
Cow Shed Site At Sareja ,Padra.
SR DESCRIPTION QTY UNIT RATE AMOUNT
1 Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire
of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade
FRLS PVC insulated multistrand copper wires, in following
type of pipe to be erected concealed in/ on surface on
wall/ceiling complete with 6A Modular type switch / bell push
& accessories and earth continuity of following type, erected
on PVC / Metallic box, single mounting base frame covered 4.00 Pt. 449.45
with textured/metallic front plate modules erected on / in
wall / ceiling as per pipe erected, with necessary Lamp
holder/ceiling rose / H.D.Connector as directed.
(a) with medium class Rigid PVC pipe and accessories erected
flushed on wall/ceiling complete. Cat.III
2 Point wiring for FAN with 2-1.5 sq.mm & earthwire of
sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS
PVC insulated multistrand copper wires, in following type of
pipe to be erected concealed in / flushed on wall/ceiling
complete with 6A Modular type switch and hum free EME
four or more step type electronic fan regulator with
separately mounted and accessories with earth continuity of
following type erected on PVC / Metallic box, single mounting 1.00 Pt. 638.32
base frame covered with textured/metallic front plate
modules erected on / in wall / ceiling as per pipe erected.
with necessary ceiling rose / H.D.Connector as directed.
(a) with medium class Rigid PVC pipe and accessories erected
flushed on wall/ceiling complete. Cat.III
3 Point wiring for Individual Plug with & earthwire of
sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC
insulated multistrand copper wires, in following type of to be
erected concealed in / on surface of wall / ceiling complete
with Modular type switch & 5 pin Plug erected on PVC /
Metallic box covered with appropriate front plate modules 1.00 Pt. 475.71
erected on / in wall / ceiling as per pipe erected with
following type of accessories.
[I] For 6A Plug with 2-1.5 sq.mm Cu. Wire
(a) with medium class Rigid PVC pipe and accessories erected
flushed on wall/ceiling complete. Cat.III
SBD SECTION-7 BILL OF QUANTITIES-310
4 [II] For 16A Plug with 2-2.5 sq.mm Cu. Wire
(a) with medium class Rigid PVC pipe and accessories erected 1.00 Pt. 805.98
flushed on wall/ceiling complete. Cat.III
5 Point wiring for Looped Plug with 6A Modular type switch &
pin socket erected on PVC / Metallic box, single mounting
base frame covered with textured / metallic front plate 2.00 Pt. 257.55
modules erected on / in wall / ceiling with following type
accessories Cat. III
6 Providing and erecting ISI mark Medium class RIGID PVC
PIPES of following size complete to be erected on/in wall or
ceiling erected with necessary PVC fittings & Junction boxes
fixed with adhesive solution & Clamps with following dia of
pipes, in approved manner as directed (b) 25 mm
7 Providing & erecting PVC Corrugated Flexible Conduit with
required nos. of coupling, PVC bushes, Check-nuts etc. 15.00 Mtr. 21.21
complete of following sizes. (2) 25 mm
8 Mains with 1.1 KV grade FRLS PVC insulated ISI marked
stranded Copper conductor wire in following type of pipe to
be erected concealed in /flushed on wall/ceiling, with 1.5 sq.
mm copper conductor FRLS PVC insulated stranded wire of 15.00 Mtr. 82.82
green colour for earth continuity of following size (a) with
medium class Rigid PVC pipe and accessories (b) 2 wire 2.5 sq.
9 Mains with 1.1 KV grade FRLS PVC insulated ISI marked
stranded Copper conductor wire in following type of pipe to
be erected in / on wall / ceiling with 2.5 sq. mm copper
conductor FRLS PVC insulated stranded wire of green colour 4.00 Mtr. 112.11
for earth continuity of following size (a) with medium class
Rigid PVC pipe and accessories (a) 2 wire 4 sq. mm
10 Providing and erecting Sheet Steel powder coated MCB
distribution board - flush / surface mounted fitted with
busbar, neutral link, earth bar and DIN rail, Conforms to IS
8623-1 & 3, IEC 61439-1 & 3 without MCB to house
appropriate nos. of MCBs.(The DBs should be used of same
company of MCB to be used) suitable for (B)(iii) Three phase
8 way SS Double door for horizontal single phase outgoing
11 providing and erecting Miniature circuit breaker single pole
6A to 25A suitable to operate on 240 V A.C. system and
having breaking capacity 10 KA to be erected in existing box. 1.00 Ea. 112.11
confirming to IS 8828/1996 with ISI Mark Cat.III
SBD SECTION-7 BILL OF QUANTITIES-311
12 Providing & erecting 240 V MCB double pole switch for motor
& inductive load (C Curve) having 10 KA breaking capacity &
confirms to IS : 8828 in existing box having following capacity
(B) 40 Amp. Cat.III
13 Providing & erecting L.T. Current Transformer with bar
primary 50/5 to 1000/5 ratio 15 VA burden erected in existing
CRCA box duly secured with insulating materials connected to
14 Supplying and erecting approved make set of indicator lamps
of LED type lamp, lens cover, Bakelite holder complete 1.00 Ea. 126.25
erected with necessary connections.
15 Supplying & erecting funnel type earthing having earth plate
of following size burred in specifically prepared earth pit
mtr. below ground with 40 kg. charcoal and salt with
alternate layers of charcoal & salt, 20mm.dia. G.I. pipe with
Funnel with a wire mesh for watering & bricks masonry block,
C.I. Cover complete as per para 7.3 of IS 3043 with necessary
length of double Galvanised Iron / copper earth wire No
SWG bolted with lug to the plate and covered in 12 mm dia.
G.I. pipe 2.5 mtr long complete connected to the nearest
switch gear with end socket as per direction & duly tested by
earth tester confirming to IS (As per drawing) with following
(B) With 45 x 45 x 0.35 cms. C.I. earth plate 1.00 Ea. 2568.43
16 Mains with ISI marked, 1.5KV grade electrolyte multi
stranded, annealed copper conductor with heat resistant PVC
insulated conforms to IS 694, IEC - 227 erected in existing
pipe of following size (Specifically for control panel, relays, 4.00 Mtr. 53.53
power switchgears, motor starters & control wiring) with
required size of copper lugs, nuts and bolts if required. (e)
One wire 6.00 sq. mm
17 Making trench in soft soil of suitable width of 90 cms deep for
laying cable or locating the fault all over the run and
backfilling the same and making the surface as normal
18 Providing and, fixing heavy duty flange type brass cable gland
with rubber ring for PVC insulated armoured cable complete
with out going tails, insulating tape etc for following size of
cables. (E) 2 to 4 core 25 Sq. mm
19 Providing and, fixing heavy duty flange type brass cable gland
with rubber ring for PVC insulated armoured cable complete
with out going tails, insulating tape etc for following size of
cables. (H) 3 & 1/2 core 240 Sq. mm
SBD SECTION-7 BILL OF QUANTITIES-312
20 Solderless crimping type Aluminium lugs conforming to IS
suitable for cable of following size evenly crimped with high
pressure tool & connected to switchgear terminals with
brass/cadmium plated nut bolts in an approved manner.
21 Providing and erecting Approved make Ceiling fan with
double ball bearing ISI mark with condenser A.C. 23OV.50
c/s.1200 mm. sweep complete, canopy and 30 cms. down rod
erected on existing hook or clamp with 24/0.2 , 3 core flexible
wire with earthing. [Make shall be approved by Engineer in
22 Providing 2.5mm.thick laminated acrylic sheet to cover the
fan hook or Fan box.
23 Providing Fan clamp of 30 x 5 mm flat of required length &
mm M.S. Bolt & Nuts erected with necessary hook of 10 mm 1.00 Ea. 98.98
M.S. Round Bar.
24 Supplying & erecting energy saving Energy Efficient E+ (1 -
ft) 28 watt retrofit tube fitting with one no 28watt T-5 tube
complete with E.G.P. wings reflector / clear acrylic guard
cover & tube and electronic inbuilt circuit ballast of rating 2.00 Ea. 493.89
130 to 325 V A.C. The fittings should be able to fit in any
conventional existing T - 8 tube fittings complete erected in
an approved manner.
25 Approved make C.F.L. Retrofit 13/15/18 Watt erected if
26 Supplying & erecting approved make low noise decorative
exhaust fan having size 200mm with 1350 RPM with square
frame ABS body with inbuilt lowers & square frame.
ADD 18.00 % GST
SBD SECTION-7 BILL OF QUANTITIES-313
Name of work :- Drilling of 165mm dia x 90 Mts. Deep DTH bore with providing & installation of single phase sub.
Pump set at following location of Nagarpalika area of Padra.
Location: SAREJA PADRA
Qty. Unit. Item. Rate Per Amount
Drilling Section:
1 Per No. Geohydrological ground water investigations including vehicle 3571.00 Per No.
charges. (a) Borewell for single phase / Hand Pump
90 RMT. Drilling of 215 mm dia. Bore in over burden strata (0-30) including 300.00 RMT
lowering and fixing of 175 mm nominal dia UPVC pipe/175 mm dia
ERW pipe upto required depth and further drilling of 165mm dia
bore hole in rocky strata by DTH rig.
24 RMT. Manufacture, supply and delivery of ISI marked (IS-12818) with 906.00 RMT
latest amendment. Rates are Exclusive of GST
c) 175 mm nominal dia. "CS" type
1 No. Bore Plug of 100 mm Height made from 5 mm thick M.S. plate (For 654.96 No.
top also) with 3 holes at equal distance on circumference for nut –
bolts type, locking arrangement with nuts–bolts & lock nuts of std.
Pumping Machinery Section:
1 No. Providing & Supplying Single phase Borewell sub pump motor set 10750.00 No.
with control panel Cat Q : 1.2 ,20 LPM/90 mtr Head 1.5 HP
MOC: Casing: CI-FG260, Impeller : Bronze & Shaft : SS:410
115.00 RMT. PVC insulated flat submersible cable as per detailed technical 58.00 RMT.
specifications of R/C of GWSSB conforming to IS 694, IEC 60227/
95.00 RMT. Manufacture, Supply and delivery of following ISI marked HDPE 55.00 RMT.
Pipes (IS:4984/1985 with latest amendment) having material Grade
PE-80 in approximate 100 meter Coil length or as per GWSSB
requirement with SS-316 Nipple at both ends having 11 TPI threads
as per specification, press fitted and bolted having nominal
diameter as under as per detailed technical Specification. (Note:
Above rates of HDPE Pipes based on IOCL Resin A Grade 45 GP
004DP44 as on dated 01.11.2021 Rs. 117669/- Rates are Inclusive
of GST. DN-40 PN-10
SBD SECTION-7 BILL OF QUANTITIES-314
Clamps made from MS plate with 3 holes on either side side with
nuts & bolts of standard make and suitable size.
1 Pair a) 450mm x 50mm x 10mm flat suitable to 32mm dia pipe. 370.65 Pair
3 Kg. GI Fittings of 32 mm dia. for Jointing pipe line as per actual 71.76 Kg.
requirement as per Anx. (A) Upto 65 mm dia.
(Mech. SOR 2022-23, Setion-B, Item No. 19(A),Page No.24)
1 Sqm. Supply of Plywood sheet 9 mm thick (Commercial) for fitting of DP 230.42 Sqm.
switch and control panel board
1 Ea. Providing following type of Modular type accessories mounted with 229.60 Ea.
PVC/metallic/wooden box, single mounting base frame covered
with textured/metallic/white front plate, modules erected with
necessary connection as desired by Engineer In charge. 32 Amps.
DP switch with indicator. Cat.III
1 Job Lowering of Single phase submersible pump set complete with 700.00 Job
required length of HDPE pipe & cable in bore well and fitting of
control panel board including wiring work and satisfactory testing
as per instruction of Engineer-in-charge at different villages
including carting/ loading/ unloading of material to site for bore
depth upto 70 mts.
1 No. Providing dust and vermin proof MS cabin having two 5040.00 No.
compartments, one for panel board and other for energy meter and
fuse unit with required locking arrangement, minimum degree of
protection IP 52 as per IS 2147 fabricated from CRCA sheer Steel
minimum thickness for base frame/channel/gland paltes for 3mm
for load bearing members, 1.6mm for internal members including
cutting, bending, drilling, welding, riveting with internal partitions.
The sheet stell enclosure shall be powder coated as per applicable
standard with shade as required with finish thickness of paint film
not less than 80 microns. The cabin shall following dimension.
Add :18% GST Charge
SBD SECTION-7 BILL OF QUANTITIES-315
PADRA MUNICIPALITY, PADRA
CONSTRUCTION WORK OF PROPOSED ROOFING SHED ON COW COMPOUND WALL AT SAREJA,
Qty. Description Unit Amount
1 10.00 Boring holes 3.5 m deep in ordinary soil (for cast in situ piles) and
Each getting out the soil and disposal of the surplus excavated soil as
directed within a lead of 50 Meter for following diameter of
pipes.(iii) 350 mm 1523.30 Each
2 10.00 Add to or deduct from the rate for Bore Holes of 3.5 m Depth, if
Each bore holes are made deeper or shallower than 3.5M. for Piles of
following diameter.(iii) 350 mm
3 28.45 Excavation for Foundation upto 1.5 m. Depth including sorting
Cmt. out and stacking of useful materials and disposing of excavated
stuff upto 50 Meter lead (A) (loose or soft soil)
4 15.90 Filling available excavated earth (excluding Rock) in trenches.
Cmt. Plinth, sides of foundations etc. in layers not exceeding 20cm. In
depth consolidating each disposited layer by ramming and
watering. 133.65 Cmt.
5 8.90 Providing and laying cement concrete 1:4:8(1 Cement, 4 coarse
Cmt. sand, 8 graded stone aggregates 20mm nominal size) and curing
complete excluding cost of formwork in Foundation and Plinth
6 13.75 Providing and Laying controlled cement concrete M-250 and
Cmt. curing complete, including the cost of formwork and
reinforcement for reinforced concrete work in Column footings.
7 3.65 Providing and Laying controlled cement concrete M-250 and
Cmt. curing complete, including the cost of formwork and
reinforcement for reinforced concrete work in Columns(Padestal)
SBD SECTION-7 BILL OF QUANTITIES-316
8 2.45 Providing and Laying controlled cement concrete M-200 and
Cmt. curing complete, including the cost of formwork and
reinforcement for reinforced concrete work in Columns
9 15.00 Providing and Laying controlled cement concrete M-250 and
Cmt. curing complete, including the cost of formwork and
reinforcement for reinforced concrete work in Ground Beam
3393.25 Providing TMT Bar FE 500D reinforcement for R.C.C. work
Kgs. including bending, binding and placing in position complete upto
floor two level 77.29 Kg.
11 193.78 Steel work, welded in built up sections framed work including
Qtl. cutting, hoisting, fixing in position and applying a priming coat of
read lead paint. (A)In beams and joists, channels angles Tees,
flats, with connecting plates or angle cleats as in main and cross
beams. Hip and jack rafters, purlins conneted to common rafters
and the like (upto 10 ton) 9108.48 Qtl.
12 823.20 Painting two coats (Including priming coat) on new steel and
Smt. other metal surface with enamel paint, brushing, interior to give
an even shade including cleaning the surface an even shade
including cleanicn the surface of all dirt, dust and other foreign
matter. 125.72 Smt.
13 1646.40 Providing corrugated G.I. sheet of class-3 roofing fixed with
Smt. glavanished iron J or L Hooks, Bolts and nuts 8mm diameter with
bitumen and G.I. limpet washer or G.I. limpet washer. filled with
white lead complete excluding the cost of purlins, Rafters and
Trusses.(1) 0.80 mm thick sheet. 734.19 Smt.
14 29.25 Providing and Laying 20 mm thick sand face cement plaster on
Smt. Walls upto height of 10 mts. Above ground level consisting of
12mm thick backing coat of C.M 1:3 (1 Cement, 3 Sand ) and
mm thick finishing coat of C.M 1:1 (1 Cement, 1 Sand) etc.
complete. 337.52 Smt.
15 83.40 Providing and fixing 150mm wide 450mm over all semicircular
Smt. plain G.I.sheet class-3 gutter with Iron brackets 40mm x 3mm size
Bolts, Nuts, washers etc. including making necessary connection
with rain water pipes. (i) 0.80 mm thick Sheet.
SBD SECTION-7 BILL OF QUANTITIES-317
16 29.25 Finishing wall with weather proof exterior emulsion paint on wall
Smt surface (two coats) to give an required shape even shade after
thoroughly brushing the surface to remove all dirt, and remains of
loose powdered materials.etc complete 117.40 Smt.
17 20.00 Providing and fixing on wall face C.I. Rain water pipe including
Rmt filling the joints with spun yarn soaked in neat cement slurry and
cement mortar 1:2 (1- Cement : 2-fine sand) (A) 75 mm dia.
SBD SECTION-7 BILL OF QUANTITIES-318
PADRA MUNICIPALITY, PADRA
ESTIMATE FOR PROVIDING AND LAYING OF 600 MM DIA R.C.C. NP3 PIPE ( TWO ROW ) STROM WATER
DRAIN PATDIYA HANUMAN TEMPLE AT PADRA.
No. Qty. DESCRIPTION Per Amount
1 33.00 Excavation for foundation upto depth 1.5 m. including sorting out
Cmt. andstacking of useful materials and disposing of the excavated
stuff up to 50 m lead (loose or soft soil)
2 6.00 Filling with available excavated earch (excluding rock) in trenches,
Cmt. plinth sides of foundation etc. in layer not exceeding 20cm in
depth consolidation each disposited layer by ramming and
watering. 133.65 Cmt.
3 35.00 Providing and supplying ISI Standard R.C.C. pipes(of Sulphate
Rmt. Resisting Cement) in standard lengths of following class and
diameter suitable for either collar joints or rubber ring joints
including all taxes, insurance, transportation,freight charges,
octroi, inspection charges, loading, unloading, conveyance to
departmental stores, stacking etc.complete. (IS - 458/ 1989110 x
4 35.00 Lowering, laying and jointing R. C. C. pipes in C. M. 1:1 1/2 of
Rmt. following diameters in proper position, grade and alignment at all
level as directed by Engineer-in-charge including conveyance
from stores to site of work, labour, giving hydraulic testing as per
5 5.00 Providing and filling sand below R.C.C. Raft in layers including
Cmt. ramming and watering complete. (laying Below 600mm dia pipe)
SBD SECTION-7 BILL OF QUANTITIES-319
6 1.00 Construction of Brick masonry chamber for pipe drain including
Nos. excavation, p.c.c. (1:4:8), Brick Wall 350 mm thick, M-200
coping, M-200 slab, 10 mm thick (1:3) smooth plaster and
including M.S. frame and cover with all necessary labour and
material in all respect directed by EIC.
Inner Clear Dimensions 1.80 x 1.60 x 1.30 60537.84 Nos.
Add : 18% of GST, Rs.
SBD SECTION-7 BILL OF QUANTITIES-320
Name of work :- DRILLING OF 165MM DIA X 90 MTS. DEEP DTH BORE WITH PROVIDING & INSTALLATION OF SINGLE
PHASE SUB. PUMP SET AT MRF SHED AT SAREJA, PADRA
Location: MRF SHED SAREJA PADRA
Qty. Unit. Item. Rate Per Amount
Drilling Section:
1 Per No. Geohydrological ground water investigations including vehicle 3571.00 Per No.
charges. (a) Borewell for single phase / Hand Pump
90 RMT. Drilling of 215 mm dia. Bore in over burden strata (0-30) including 300.00 RMT
lowering and fixing of 175 mm nominal dia UPVC pipe/175 mm dia
ERW pipe upto required depth and further drilling of 165mm dia
bore hole in rocky strata by DTH rig.
24 RMT. Manufacture, supply and delivery of ISI marked (IS-12818) with 906.00 RMT
latest amendment. Rates are Exclusive of GST
c) 175 mm nominal dia. "CS" type
1 No. Bore Plug of 100 mm Height made from 5 mm thick M.S. plate (For 654.96 No.
top also) with 3 holes at equal distance on circumference for nut –
bolts type, locking arrangement with nuts–bolts & lock nuts of std.
Pumping Machinery Section:
1 No. Providing & Supplying Single phase Borewell sub pump motor set 10750.00 No.
with control panel Cat Q : 1.2 ,20 LPM/90 mtr Head 1.5 HP
MOC: Casing: CI-FG260, Impeller : Bronze & Shaft : SS:410
115.00 RMT. PVC insulated flat submersible cable as per detailed technical 58.00 RMT.
specifications of R/C of GWSSB conforming to IS 694, IEC 60227/
95.00 RMT. Manufacture, Supply and delivery of following ISI marked HDPE 55.00 RMT.
Pipes (IS:4984/1985 with latest amendment) having material Grade
PE-80 in approximate 100 meter Coil length or as per GWSSB
requirement with SS-316 Nipple at both ends having 11 TPI threads
as per specification, press fitted and bolted having nominal diameter
as under as per detailed technical Specification. (Note: Above rates
of HDPE Pipes based on IOCL Resin A Grade 45 GP 004DP44 as on
dated 01.11.2021 Rs. 117669/- Rates are Inclusive of GST. DN-40 PN-
SBD SECTION-7 BILL OF QUANTITIES-321
Clamps made from MS plate with 3 holes on either side side with
nuts & bolts of standard make and suitable size.
1 Pair a) 450mm x 50mm x 10mm flat suitable to 32mm dia pipe. 370.65 Pair
3 Kg. GI Fittings of 32 mm dia. for Jointing pipe line as per actual 71.76 Kg.
requirement as per Anx. (A) Upto 65 mm dia.
1 Sqm. Supply of Plywood sheet 9 mm thick (Commercial) for fitting of DP 230.42 Sqm.
switch and control panel board
1 Ea. Providing following type of Modular type accessories mounted with 229.60 Ea.
PVC/metallic/wooden box, single mounting base frame covered with
textured/metallic/white front plate, modules erected with
necessary connection as desired by Engineer In charge. 32 Amps.
DP switch with indicator. Cat.III
1 Job Lowering of Single phase submersible pump set complete with 700.00 Job
required length of HDPE pipe & cable in bore well and fitting of
control panel board including wiring work and satisfactory testing
as per instruction of Engineer-in-charge at different villages
including carting/ loading/ unloading of material to site for bore
depth upto 70 mts.
1 No. Providing dust and vermin proof MS cabin having two 5040.00 No.
compartments, one for panel board and other for energy meter and
fuse unit with required locking arrangement, minimum degree of
protection IP 52 as per IS 2147 fabricated from CRCA sheer Steel
minimum thickness for base frame/channel/gland paltes for 3mm
for load bearing members, 1.6mm for internal members including
cutting, bending, drilling, welding, riveting with internal partitions.
The sheet stell enclosure shall be powder coated as per applicable
standard with shade as required with finish thickness of paint film
not less than 80 microns. The cabin shall following dimension. 1.
2000 No. Supplying And fixing PVC water tank of ISI make including delivery 3.91 No.
at site, supply and fixing inlet, outlet, overflow, ballcock, drainage
sleeves of specific size, with necessary neoprene gasket / packing /
washer, G.I.washer, and checknut etc. compt as directed on
terrace,loft,bathroom etc in any height.The rate shall be include for
fixing additional accessories supplied by supplyer accessories.
SBD SECTION-7 BILL OF QUANTITIES-322
50 No. Providing, laying and jointing in true line and level 32 mm dia 117.97 No.
U.P.V.C. Pipe (SCH-40) including fittings make as approved by
Engineer In Charge. Pipe shall be fixed on the wall with the help of
clamp at every two meter c/c. or shall be concealed as directed
including necessary fittings etc. including testing of pipe and joints
and fixing the same with adhesive solvent, including cost of all
50 No. Providing, laying and jointing in true line and level 25 mm dia 90.93 No.
U.P.V.C. Pipe (SCH-40) including fittings make as approved by
Engineer In Charge. Pipe shall be fixed on the wall with the help of
clamp at every two meter c/c. or shall be concealed as directed
including necessary fittings etc. including testing of pipe and joints
and fixing the same with adhesive solvent, including cost of all
Add :18% GST Charge
Add :1% labour Cess
SBD SECTION-7 BILL OF QUANTITIES-323
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
RAW_HTML
BOQ.pdf
Notes.pdf
OTHER IMPORTANT-1.pdf
OTHER IMPORTANT-2.pdf
OTHER IMPORTANT-3.pdf
SBD.pdf
Download all tender documents and submit your bid