Construction of Ayurvedic Health Centre building at Paisa TehsilDehra District Kangra HP

Amount

Excavation in foundation trenches etectra in earth work in all kinds of classification of soil such as pick work, jumper work, pick jumper work, blasting work, soft and hard blasting and doing work in saturated soil, including chiseling or wedging out rock where blasting is prohibited, or any other mixed variety of soil including shoring, strutting, de-watering and pumping or bailing out water (surface and sub soil water) upto any depth or any quantum of water including slush which may arise during dewatering, removal of slush and stacking the excavated soil clear from the edge of excavation with in all leads, as directed by Engineer-in-Charge and then returning the stacked soil in 15cm (fifteen centimeters) layers when required into plinths, sides of foundations etc. consolidating each deposited layer by ramming watering and then disposing of all surplus excavated earth as directed by Engineer-in-Charge with in all leads and lifts, disposed earth to be levelled and neatly dressed including carriage of materials within all leads and lifts.

Filling in plinth with sand of approved quality under floors including watering ramming, consolidating and dressing complete as per HPPWD specifications and as directed by Engineer-in-Charge, including carriage of material within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated plain cement concrete 1:4:8 (one cement isto four sand isto eight graded crushed stone aggregate 40mm (Forty millimeter) nominal size) and curing complete, in or under water, including pumping or bailing out water/dewatering, removal of slush which may arise at the time of laying under water complete excluding the cost of form work in foundation and plinth in all depths/heights as per HPPWD specifications and as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government.

Providing and laying damp proof course 40mm (Forty millimeters) thick with cement concrete 1:2:4 (one cement isto two sand isto four graded crushed stone aggregate 12.5mm (twelve decimal five millimeter) nominal size and curing complete including cost of form work and as required at site and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Royality, Malkhana, Octroi, Toll Tax Sales tax or any other taxes imposed by the Government.

Applying a coat of hot bitumen mexphalt 80/100 (eighty/hundred) or equivalent using 1.70 Kgs. (one decimal seven zero kilogramms) per square meter on damp proof course after cleaning the surface with a piece of cloth lightly soaked in kerosene oil including carriage of materials within all leads, lifts and other incidental and as per the direction of Engineer-in-Charge. The rate inclusive of Malkhana, Octroi, Toll Tax Sales tax or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated reinforced cement concrete work of Grade M-25 (Twenty five) design mix to obtain the minimum compressive strength of 20 N/mm2 (twenty newton) per square millimeter with cement contents not less than 400 Kg (Four hundred) Killogramme per cubic meter and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated reinforced cement concrete work of grade M-25 (M-Twenty five) design mix to obtain the minimum compressive strength of 25 N/mm2 (twenty five newton) per square millimeter with minimum cement contents of 400kg (Four hundred kilogrammes) per cubic metre and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in beams, suspended floors, roofs having slope up to any degree, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases etcetra up to all floor level as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated reinforced cement concrete work of grade M-25 (M-Twenty five) design mix to obtain the minimum compressive strength of 25 N/mm2 (twenty five newton) per square millimeter with minimum cement contents of 400kg (Four hundred kilogrammes) per cubic metre and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in foundation footings, bases of columns, walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etcetra up to all floor level complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three point one five millimeter) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeter) so as to give a fair finish including centering, shuttering strutting and propping etcetra with wooden battens and ballies, height of propping and centering in all heights. below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in Suspended floors, roofs, landings, balconies and access platform as per specifications, approved drawing and design, and as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three decimal one five millimeter) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeter) so as to give a fair finish including centering, shuttering strutting and propping etcetra with wooden battens and ballies, heights of propping and centering in all heights below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors, roofs, landings, shelves, and the like floor, etcetra up to any thickness, up to all floor level as per specifications, approved drawing, design and as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three point one five millimeter) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeter) so as to give a fair finish including centering, shuttering strutting and propping etcetra with wooden battens and ballies, height of propping and centering in all heights. below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in Shelves (Cast in situ) as per specifications, approved drawing and design, and as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three point one five millimeter) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetra with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers, girders and lintels, sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto any depth/heights, up to all floor level as per specifications, approved drawing, design and as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three decimal one five millimeter) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeter) so as to give a fair finish including centering, shuttering strutting and propping etcetra with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in stairs cases with slopping or stepped soffits, excluding, landing, up to all floor level as per specifications, approved drawing, design and as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three decimal one five millimeter) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetra with wooden battens and ballies, heights of propping and centering in all heights below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls upto any width, up to all floor level as per specifications, approved drawing, design and as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government.

Providing and laying Tor steel of TATA/SAIL reinforcement thermo mechanically coated bars of grade Fe 500D for Reinforced Cement Concrete work including bending, binding and placing in position complete including cost of binding wire and other incidentals for its completion up to all floor levels as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (Seven point five) in foundation and plinth above plinth level upto all floor level in cement mortar 1:6 (one cement isto six sand) and curing complete as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Half Brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (Seven point five) in super structure above plinth level upto all floor level in cement mortar 1:3 (one cement isto three sand) and curing complete as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Random rubble masonry brought to courses with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement is to six sand is to twelve graded crushed/broken stone aggregate 20mm (twenty millimeter) nominal size) at plinth level in cement mortar 1:6 (one cement isto six sand) and curing complete as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth upto all heights/ depths including pumping or bailing out water/dewatering including racking out joints in cement mortar 1:6 (one cement isto five sand) complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and laying 40mm (Forty millimeters) thick cement concrete flooring 1:2:4 (one cement is to two sand is to four graded crushed stone aggregate 20mm (twenty millimeters) nominal size) mechanically mixed laid in one layer finished with a floating coat of neat cement and curing complete up to all floor level as per HPPWD specifications or as directed by the Engineer-in-Charge, including carriage of materials within all leads and lifts. The rate inclusive of Octroi, Toll tax, GST or any taxes imposed by the Government.

Providing and fixing 18mm (Eighteen millimetre) thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20mm 9Twenty millimetre) thick base cement mortar 1:4 (one cement isto four coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels area of slab over 0.50 Sqm (Zero point five zero) as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 35mm (Thirty five millimetre) thick factory made flush door shutter both side commerical (Non-decorative) phenol bonded termite resistant and bailing water proof core of block board construction with frame of first class hard wood and well matched commercial ply veneer with vertical grains or cross band and face veneer on both faces of flush door shutter ISI marked IS No.-2202 of Centuary ply board /Kitply) green ply complete including carriage of material within all leads and lifts and other incidentals as per specifications approved, drawings, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured) complete as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 20mm (Twenty millimetre) dia chromium plated brass curtain rod having wall thickness of 1.25mm (One point two five millimetre) with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete fixed to steel windows by welding as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 200x10mm (Two hundred into ten millimeters) oxidised mild steel tower bolts (Barrel type) make of pilot/sheel or equivalent anodized transparent or dyed to required colour and shade with screws etc. complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Octroi, Toll tax, GST or any taxes imposed by the Government.

Providing and fixing 250x20x6mm (Two hundred fifty into twenty into six millimetre) ISI marked oxidised M.S. door latches conforming to IS:5930 with screws etc. complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Octroi, Toll tax, GST or any taxes imposed by the Government.

Providing and fixing 300x16mm (three hundred into sixteen millimeters) aluminum Matt finished sliding door bolts, make of PILOT/Sheel or equivalent anodized transparent or dyed to required colour and shade with necessary bolts, nuts and screws etcetera complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Octroi, Toll tax, GST or any taxes imposed by the Government.

Providing and fixing 250x16mm (two hundred fifty into sixteen millimeters) aluminum Matt finished sliding door bolts, make of PILOT/Sheel or equivalent anodized transparent or dyed to required colour and shade with necessary bolts, nuts and screws etcetera complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Octroi, Toll tax, GST or any taxes imposed by the Government.

Providing and fixing 300x10mm (three hundred into ten millimeters) aluminum Matt finished tower bolts (Barrel type) make of pilot/sheel or equivalent anodized transparent or dyed to required colour and shade with screws etc. complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Octroi, Toll tax, GST or any taxes imposed by the Government.

Providing and fixing 250x10mm (two hundred fifty into ten millimeters) aluminum Matt finished tower bolts (Barrel type) make of pilot/sheel or equivalent anodized transparent or dyed to required colour and shade with screws etc. complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Octroi, Toll tax, GST or any taxes imposed by the Government.

Providing and fixing 200x10mm (two hundred into ten millimeters) aluminum Matt finished tower bolts (Barrel type) make of pilot/sheel or equivalent anodized transparent or dyed to required colour and shade with screws etc. complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. TThe rate inclusive of Octroi, Toll tax, GST or any taxes imposed by the Government.

Providing and fixing 125mm (one hundred twenty five millimeters) aluminium handles make of pilot/sheel or equivalent transparent or dyed to required colour and shade with necessary screws etc. complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government.

Extra for providing and fixing steel beading of size 10x10x1.6mm (Ten into ten int one point six millimetre) (box type), approved shape and section with screws instead of glazing clips and metal sash putty, in steel doors, windows, ventilators and composite units complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel of TATA/SAIL as required In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Octroi, Royality, Malkhana, Toll tax, Sale tax, GST or any other taxes imposed by the Government.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing,staircase railing and similar works, including applyingpriming coat of approved steel primer.M.S. tube as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Octroi, Royality, Malkhana, Toll tax, Sale tax, GST or any other taxes imposed by the Government.

Providing and fixing mild steel channels in door and windows frames manufactured from mild steel channels 75x40x5mm (Seventy five into forty into five millimeter) thick for end frame and for centre frame section 75x40mm (Seventy five into forty millimeter) welded together with MS flat/plate 75x5mm (seventy five into five millimeters) to make mullion including providing MS flat 40x4mm (forty into four millimeters) welded at suitable intervals for welding with hold fast including hinges jamb, lock jamb beed and if required angle thrashold of MS angle 50x25mm (fifty into twenty five millimeters) welded or rigidily fixed by mechanical means with split end tails to each jamb including provision of locking arrangement, shock absorber and steel but hinges 2.5mm (two point five millimeter) thick and double acting spring hinges complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate is inclusive of Octroi, Royality, Malkhana, Toll tax, Sale tax, GST or any other taxes imposed by the Government.

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings,complete all as per approved design, (sectional weight of only steel members shall be measured for payment) Fixing with 15x3mm (Fifteen int three millimetre) lugs 10cm (Ten centimetre) long embedded in cement concrete block 15x10x10cm (Fifteen into ten into ten centimetre) of C.C 1:3:6 (One cement isto three coarse sand isto six graded stone aggregate 20mm (Twenty millimetre ) nominal size complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate is inclusive of Octroi, Royality, Malkhana, Toll tax, Sale tax, GST or any other taxes imposed by the Government.

Providing and fixing stainless steel (Grade 304) fly proof wire gauge of 0.5mm (Zero point five millimetre) dia wire and 1.4mm (One point four millimetre) operature on both side of windows, clear story widows and doors with nuts and bolts complete as per specitations approved, drawings, design and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 5.5mm (Five point five millimetre) thick glass panes of modi guard/saint gobain (weight not less than 15.00 kg/ sqm (Fifteen kilogram per square metre) glazing in aluminium door, window, ventilator shutters and partitions etcetra with EPDM rubber / neoprene gasket etcetra complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing SST stainless steel & Grade 300 ) railing for ramp for divyang with 50mm (fifty millimeter) dia SST pipe handrail slip resistant with round ends at two level at 75 and 90cm (Seventy five and ninety centimeter) height and extended 30cm (thirty centimeter) beyond the top and bottom of railing with 25mm (Twenty five millimeter) dia SST pipe balusters welded to 50mm (fifty millimeter) dia SST pipe embeded in cement concrete at 600mm (six hundred millimeter) cente to centre duly welded with MS flat 50x5mm (fifty into five millimeter) as per HPPWD specifications approved drawing, design or as directed by the Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Octroi, GST, toll tax or any other taxes imposed by the Government.

roviding and laying upto all floor level, 300x300x25mm (three hundred into three hundred into twenty five millimeters) thick automatic hydraulically compressed and polished terrazzo tiles ISI marked number IS-1237 of NTC or its equivalent in 70% (seventy percent) white and 30% (thirty percent) grey cement with the ratio of chips shall be 55% (fifty five percent) white chips, 15% (fifteen percent) each maroon, yellow and dark green having chips sizes O, B, 2 B laid in floor, treads of steps and landing on a bed of 20mm (twenty millimetre) average thickness of cement mortar 1:4 (one cement isto four sand) and jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) including rubbing and polising complete with silver grey shade tiles upto all floor level as per HPPWD specification or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Royality, Octroi, Toll tax, GST or any taxes imposed by the Government.

Providing and laying anti skid ceramic tiles of Restile/ Nitco/ Rak/ Simpolo/ AGL/ Kajaria/ Johnson/ Orient bell/ Somany of 300x300mm (Three hundred millimetre into Three hundred millimetre) size manufactured of approved shade and colour in floor (thickness to be specified by the manufacturer), with water absorption less than 0.08% (Zero point zero eight percent) and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive of approved brand (water based) conforming to IS : 15477, in average 6mm (Six millimetre) thickness, including grouting of joints complete as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying upto all floor level, 300x300x25mm (three hundred into three hundred into twenty five millimeters) thick automatic hydraulically compressed and polished terrazzo tiles ISI marked number IS-1237 of NTC make in 50% (Fifty percent) white and 50% (Fifty percent) grey cement yellow and dark green having chips of specified size O and B (No. SG-403 B) of approved brand/make and of approved shade, with marble chips of white laid in skirting, risers of steps and dado upto any height, laid on a bed of 10mm (ten millimeters) average thickness of cement plaster 1:3 (one cement isto three sand) jointed with white/grey cement slurry mixed with pigment to match the shade of tiles (wherever required) including rubbing and polishing complete as per HPPWD specification or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Royality, octroi, GST, toll tax or any taxes imposed by the Government.

Providing and laying upto all floor level ceramic coloured glazed tiles of size 300x450mm (three hundred into four hundred fifty millimeters) of approved brand and make Kajaria/Nitco/ Somany/Bell/ Janson/swastik tiles in skirting, risers of steps and dado for all heights, laid on a bed of 12mm (twelve millimeters) thick cement mortar 1:3 (one cement is to three sand) and jointed with white cement slurry complete as per HPPWD specification and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Royality, Malkhana, Octroi, GST, toll tax or any taxes imposed by the Government.

Providing and laying 25mm (Twenty five millimeter) thick Mirror polished Kota stone slab 55x55cm (fifty five into fifty five centimeter) mirror polished with 7.5cm (seven point five centimeter) wide internal designing with ratio of 70% and 30% as per detail in drawings Jaislmer band yellow in flooring laid over 20mm (twenty millimeter) thick base of cement mortar 1:4 (one cement isto four sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing nousing ans moulding complete upto all floor level as per HPPWD specification or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Royality, Octroi, GST, toll tax or any taxes imposed by the Government.

Providing and laying 25mm (Twenty five millimeter) thick single slab with round nousing Mirror polished Kota stone slab in risers of steps, skirting dodo and pillars laid on 12mm (twelve millimetre) average thick cement mortar 1:3 (one cement isto three sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etcetera up to all floor level, complete as per HPPWD specification and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Royality, Malkhana, Octroi, GST, toll tax or any taxes imposed by the Government.

Providing and laying 300x300x25mm (three hundred into three hundred into twenty five millimeter) labrador design (rainbow series) tiles of NTC, of approved shade in flooring/ treads of steps etcetera laid on a bed of 12mm (twelve millimeter) thick cement mortar 1:3 (one cement isto three sand) and jointed with cement slurry as required up to all floor level, complete as per HPPWD specifications and as directed by the Engineer,-in-Charge, including carriage of materials within all leads, lifts, and other incidental. The rate including Royality, Malkhana, Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government.

Providing and laying semicircular S.W stone ware pipe 150mm (one hundred fifty millimeter) dia over a bed of CC 1:1.5:3 (one cement isto one and half sand isto three graded crushed stone aggregate) including jointing the SW stone ware pipe with each other in drain within SR square rubble masonry edge wall of drain including carriage of material upto all leads and lifts and as per direction of Engineer incharge, including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Royality, Malkhana, Octroi, Toll Tax, GST, Sales tax or any other taxes imposed by the Government.

Providing and laying 60mm (Sixty millimetre) thick factory made cement concrete paver block of M-30 (Thirty) grade with approved color design and pattern of NTC/UNISTONE/ATLANTICA chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etcetra of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing on wall face Single socketed 110 mm (One hundred ten millimetre) diameter unplasticised Rigid PVC (Polyvinyl chloride) rain water pipes conforming to IS : 13592 Type A make of Finolex/ Relpipe (Reliance)/Supreme including jointing with seal ring conforming to IS : 5382, leaving 10mm (Ten millimetre) gap for thermal expansion complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing on wall face 110 mm (One hundred ten millimetre) diametre plain bend unplasticised - PVC (Polyvinyl chloride) moulded fittings/ accessories for unplasticised Rigid PVC (Polyvinyl chloride) rain water pipes conforming to IS : 13592 Type A of Finolex/ Relpipe (Reliance)/Supreme including jointing with seal ring conforming to IS : 5382, leaving 10mm (Ten millimetre) gap for thermal expansion complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing on wall face 110 mm (One hundred ten millimetre) shoe unplasticised - PVC (Polyvinyl chloride) moulded fittings/ accessories for unplasticised Rigid PVC (Polyvinyl chloride) rain water pipes conforming to IS : 13592 Type A Finolex/ Relpipe (Reliance)/Supreme including jointing with seal ring conforming to IS : 5382, leaving 10mm (Ten millimetre) gap for thermal expansion complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm (Fifty into fifty into fifty millimetre)hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (One cement isto four coarse sand) and making good the wall etc. complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and applying 15mm (fifteen millimeter) thick cement plaster with cement mortar 1:6 (one cement isto six sand) in single coat on rough side of brick/concrete/ stone walls for interior plastering up to all floor level including arises, internal rounded angles, chamfers or rounded angles in all girth and finished even and smooth as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 12mm (Twelve millimeter) thick unistone cladding on R.C.C surface side as on faces of Arch masonry walls etcetra on 12mm (Twelve millimeter) thick cement plaster 1:3 (one cement isto three sand) and jointed with cement slurry including scaffolding etcetra complete upto all floor level as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and applying 6mm (six millimeter) thick cement plaster to ceiling with cement mortar 1:3 (one cement isto three sand), up to all floor level complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and applying 20mm (Twenty millimeters) thick cement plaster with cement mortar 1:4 (one cement isto four sand) in single coat on rough/fair side of brick/concrete/ stone walls for interior plastering up to all floor level including arises, internal rounded angles, chamfers and/or rounded angles in all girth and finished even and smooth for septic tank complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying 20x20mm (Twenty into twenty millimetre) square bar M.S. foot rests including fixing in manholes with 20x20x10cm (Twenty into twenty into ten centimetre) cement concrete blocks 1:3:6 (One cement isto three coarse sand isto six graded stone aggregate) 20mm (Twenty millimetre) nominal size complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and applying white cement based putty of average thickness 1mm (One millimtre), of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete upto all floor level as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and applying Distempering (two or more coats) with delight Aerylic washable of NCL Allteck distemper of approved brand and manufacture (Nerolac/Asian or equivalent make) and of required shade on un-decorated wall surfaces to give an even shade over and including a priming coat with distemper, primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth upto all floor level as per HPPWD specification and as per the direction of Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate including Sales tax, Toll tax or any other taxes imposed by the Government.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface complete as per HPPWD specification and as per the direction of Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate including Sales tax, Toll tax or any other taxes imposed by the Government.

Finishing walls two or more coat on new work with water proofing cement paint at the rate 3.84 Kg/10 Sqm (Three point eight four kilogram per ten square metre) of required shade as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal mresistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Applying priming coat With ready mixed pink or Grey primer of approved brand and manufacture (Asian Paints/Nerolac Paints/ Burger Paints/ Dulux Paints) on wood work (hard and soft wood) complete upto all floor level as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Painting Two or more coats on new work with synthetic enamel paint of approved brand and manufacture to give an even shade as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying C.I manhole cover with frame. The weight of cover and frame to be not less than 38 kg (thirty eight kilogramme) (weight of cover 23kg (twenty three kilogramme) and weight of frame 15 kgs (fifteen kilogramme) of manhole cover 455x610mm (Four hundred fifty five into six hundred ten millimeters) complete as per HPPWD specifications or as directed by the Engineer-in-Charge including carriage of materials leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) diametre high pressure P.V.C. (Poly vinyl chloride) spigot and socket soil, waste and ventilating pipes ISI marked confirming to IS-14735-99 medium class make of Finolex/Relpipe (Reliance)/Supreme of approved manufacture including fixing with approved adhesive etcetra complete as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 110mm (one hundred ten millimeters) nominal bore/ diameters PVC cowl complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Octroi, Toll Tax, Sales tax or any other taxes imposed by the Government.

Making soak pit 2.50mtr. (Two point five zero metre) diameter 3.0 mtr. (Three point zero metre) deep with 45x45cm (Forty five into forty five centimetre) dry brick honey comb shaft with bricks and S.W. (Stoneware) drain pipe 100mm (One hundred millimetre) diameter, 1.8m (One point eight metre) long complete as per standard design with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (Seven point five) as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5m, (One point five metre) including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm (Twenty centimetre) in depth, including consolidating each deposited layer by ramming, watering, etcetra and disposing of surplus excavated soil as directed, within all lead Pipes, cables etc. exceeding 80mm (Eighty millimetre) dia. butnot exceeding 300mm (Three hundred millimetre) complete dia as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete 1:5:10 (one cement isto five sand isto ten graded crushed stone aggregate 40mm (forty millimeter) nominal size) bedding for P.V.C pipes of internal diameter 150mm (One hundred fifty millimeters) including necessary form work and curing complete and carriage of materials within all leads , lifts and other incidental. The rate including Octroi Sales tax, GST, Toll tax or any other taxes imposed by the Government.

Providing and fixing P.V.C Single equal branch with oval access door, insertion rubber washer 3mm (three millimeter) thick bolts and nuts ISI marked including finishing with approved adhesive and as per direction by the Engineer-in-Charge carriage of material with in all leads, lifts and other incidentals. The rate including Sales tax, GST, Toll tax or any other taxes imposed by the Government. 110mm (One hundred ten millimeter) diameters.

Earth work in excavation in foundation for all types of structures such as retaining walls, breast walls, culvers, drains, parapets and other similar structures in all kinds and classification of soil, including saturated soil comprising of ordinary mix soil, ordinary rock, hard rock, chiseling/ wedging out rocks (where blasting is prohibited) complete in accordance with the lines and dimensions shown on the drawings, including setting out, construction of shoring, bracing, removal of stumps and other deleterious materials and disposal of excavated material upto any leads and lifts including dressing of sides and bottom and obstructions necessary for placing the foundations, trimming, leveling ramming and watering bottom of excavation and backfilling in trenches with excavated suitable approved materials to the original surface in layers not exceeding 15cm (fifteen centimeter) compacted thickness including shoring and strutting and pumping or bailing out water (surface and sub-soil water) up to any depth and any quantum of water and cleaning of slush which may arise out during dewatering complete as per drawing and MORD Technical Specification clause 305.1 and as per the direction and the entire satisfaction of Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals.

Providing and laying mechanically mixed and vibrated cement concrete 1:4:8 (one cement isto four sand isto eight graded crushed stone aggregate 40mm (forty millimeter) nominal size) for plain cement concrete, in or under water in open foundation for all types of structures, including pumping or bailing out water/ dewatering (surface/sub-soil water) and including removal of slush which may arise at the time of laying under water for all heights/depth and any quantum of water including cost of form work and curing complete as per drawing and MORD Technical specification 802, 803, 1202 & 1203 and as per the direction and the entire satisfaction of Engineer-in-Charge, including carriage of material with in all leads lifts and other incidentals. The rates including Royality, Malkhana, Octroi, Toll tax, Sale tax, GST or any other taxes imposed by the Government.

Providing and laying 100mm (one Hundred millimeter) dia ISI marked P.V.C. pipe Weep Holes in brick masonry/stone masonry plain/ reinforcement concrete abutments, wing wall/ return wall, retaining walls and breast walls, extending through the full width of the structure with slope of 1(V): 20H (One vertical isto twenty Horizontal) towards drawing face complete as per drawing and MORD technical specification clause 614,709,1204.3.7 and as per the direction and entire satisfaction of Engineer-in-Charge complete, including carriage of materials with in all leads, lifts and other incidentals. The rates including Royality, Malkhana, Octroi, toll tax, sale tax, GST or any other taxes imposed by the Government.

Back filling behind abutment Retaining wall/Breast wall, Wing walls and the like with granular materials complete as per drawings and MORD technical specification clause 1204.3.8 and as directed by the Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. The rates including Royality, Malkhana, Octroi, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap,10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C.pan of size 580x440 mm with integral type foot rests complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Octroi, Toll Tax Sales tax or any other taxes imposed by the Government.

Providing and fixing white vitreous china pedestal type water closet European type W.C. pan of Star No. 20087 (S-10) of size 57x35x39cm (Fifty seven into thirty five into thirty nine centimeter) with PVC cistern (Sleek plus) and fixed with jet pressure of Hindware/ Cera/ Jaquar of Star white/snow white shade with seat and lid, 10 (Ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required all complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 550x440mm (Five hundred fifty into four hundred fourty millimetre) wash basin with cast iron brackets with 15mm (Fifteen millimetre) chromium plated brass pillar taps, 32mm (Thirty two millimetre) chromium plated brass waste of standard pattern of Hindware/ Cera/ Jaquar of Star white/snow white shade , including painting of fittings and brackets, cutting and making good the walls wherever require complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing white vitreous china pedestal for wash basin of Hindware/ Cera/ Jaquar of Star white/snow white shade having recessed at the back for the reception of pipes and fittings complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 8mm (Eight millimeter) diametre C.P. / S.S. Jet of Continental series of Jaquar/ Classic series of Hindware/ Floral series of Cera/ Vintage series of Kerovite/ Hindon series of JAL with flexible tube upto 1 mtr (One metre) long with S.S. triangular plate to Eureopean type W.C. of quality and make as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing G.I.inlet connection for flush pipe connecting with W C.pan complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 32mm dia P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 600x450mm (Six hundred into four hundred fifty) beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 600x120x5mm (Six hundred into one hundred twenty into five millimeter) glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. (Chromium plated) brass brackets and guard rail complete fixed with 40mm (Forty millimeter) long screws, rawl plugs etcetra complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing chromium plated brass toilet paper holder of Continental series of Jaquar/ Classic series of Hindware/ Floral series of Cera/ Vintage series of Kerovite/ Hindon series of JAL including necessary fittings complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing C.P. (Chromium plated) 15mm (Fifteen millimetre) nominal bore brass long body bib cock of Continental series of Jaquar/ Classic series of Hindware/ Floral series of Cera/ Vintage series of Kerovite/ Hindon series of JAL of approved manufacture conforming to IS standards and weighing not less than 690 gms (Six hundred ninety gram) as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm (fifteen millimeter) diameter CP stop cock of continental series of Jaguar or contessa series of Hindware complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing C.P. (Chromium plated) 15mm (Fifteen millimetre) nominal bore brass angle valve of Continental series of Jaquar/ Classic series of Hindware/ Floral series of Cera/ Vintage series of Kerovite/ Hindon series of JAL of approved manufacture for basin mixer and geyser points of approved quality conforming to IS:8931 as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing C.P. Brass extension nipple size 15x50mm (Fifteen into fifty millimetre) of approved make and quality as per direction of Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing ISI marked 45cm (forty five centimeter) long and 15mm (fifteen millimeter) nominal bore uplasticised PVC connection pipe with brass unions complete as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 2025mm OD (Two thousand twenty five) Polyethelene-Aluminium-Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C (Eighty degree celsius), including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etcetra, with clamps at 1.00 (One) metre spacing. This includes the costs of cutting chases and including testing of joints complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 1216mm OD (One thousand two hundred sixteen) Polyethelene-Aluminium-Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C (Eighty degree celsius), including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etcetra, with clamps at 1.00 (One) metre spacing. This includes the costs of cutting chases and including testing of joints complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm ( Fifteen millimetre) nominal bore G.I.pipes complete with G.I.fittings including trenching and refilling etc. complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm ( Fifteen millimetre) nominal bore brass ball valve of approved quality, High or low pressure, with plastic floats complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing water closet squatting pan (Indian brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, eighing not less than 190 gms complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing chromium plated brass soap dish of continental series of Jaquar/contessa series of Hindware with C.P. brass brackets fixed to wooden cleats with C.P. brass screws complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing PVC (Polyvinyl chloride) floor trap make of Finolex/ Relpipe (Reliance)/Supreme of approved manufacture self cleaning design including fixing with approved adhesive, cost of cutting making good the wall complete 110X90 mm ( one hundred ten into Ninety millimeter) as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5m, (One point five metre) including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm (Twenty centimetre) in depth, including consolidating each deposited layer by ramming, watering, etcetra and disposing of surplus excavated soil as directed, within all lead Pipes, cables etc. exceeding 80mm (Eighty millimetre) dia. butnot exceeding complete dia as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete 1:5:10 (one cement isto five sand isto ten graded crushed stone aggregate 40mm (forty millimeter) nominal size) S.W for P.V.C pipes of internal diameter 110mm (One hundred ten millimeters) including necessary form work and curing complete and carriage of materials within all leads , lifts and other incidental. The rate including Octroi Sales tax, GST, Toll tax or any other taxes imposed by the Government.

Providing and laying cement concrete 1:5:10 (one cement isto five sand isto ten graded crushed stone aggregate 40mm (forty millimeter) nominal size) S.W for P.V.C pipes of internal diameter 150mm (One hundred fifty millimeters) including necessary form work and curing complete and carriage of materials within all leads , lifts and other incidental. The rate including Octroi Sales tax, GST, Toll tax or any other taxes imposed by the Government.

Providing and fixing 150mm (One hundred fifty millimetre) diametre high pressure P.V.C. (Poly vinyl chloride) spigot and socket soil, waste and ventilating pipes ISI marked confirming to IS-14735-99 medium class make of Finolex/ Relpipe (Reliance)/Supreme of approved manufacture including fixing with approved adhesive etcetra complete as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) diametre high pressure P.V.C. (Poly vinyl chloride) spigot and socket soil, waste and ventilating pipes ISI marked confirming to IS-14735-99 medium class make of Finolex/ Relpipe (Reliance)/Supreme of approved manufacture including fixing with approved adhesive etcetra complete as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 150mm (One hundred fifty millimeter) diameter P.V.C (Polyvinyl chloride) double equal branch with oval access door ISI marked confirming to IS-14735-99 make of Finolex/ Relpipe (Reliance)/Supreme of approved manufacture with insertion rubber washer, 3mm (Three millimeter) thick bolts complete including fixing with approved adhesive etcetra as per HPPWD speciifications, approved drawing, design, as per the direction and entire satisfaction of the Engineer-in-Charge and carriage of material within all leads, lifts and other incidentals . The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimeter) diameter P.V.C (Polyvinyl chloride) double equal branch with oval access door ISI marked confirming to IS-14735-99 make of Finolex/ Relpipe (Reliance)/Supreme of approved manufacture with insertion rubber washer, 3mm (Three millimeter) thick bolts complete including fixing with approved adhesive etcetra as per HPPWD speciifications, approved drawing, design, as per the direction and entire satisfaction of the Engineer-in-Charge and carriage of material within all leads, lifts and other incidentals . The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government.

Providing and fixing P.V.C. (Polyvinyl chloride) plain bend ISI marked make of Finolex/ Relpipe (Reliance)/Supreme of approved manufacture including fixing with approved adhesive etcetra complete and carriage of material within all leads, lifts and other incidental Charges.The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government. P.V.C. Plain bend 150mm (One hundred fifty millimetre) Nonimal diameter

Providing and fixing P.V.C. (Polyvinyl chloride) plain bend make of Finolex/ Relpipe (Reliance)/Supreme of approved manufacture ISI marked including fixing with approved adhesive etcetra complete and carriage of material within all leads, lifts and other incidental Charges.The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government. P.V.C. (Polyvinyl chloride) Plain Bend 100mm (One hundred millimetre) (Nominal diameter)

Providing and fixing 150mm (One hundred fifty millimetre) dia. ISI marked PVC (Poly venyl chloride) clamps make of Finolex/ Relpipe (Reliance)/Supreme of approved manufacture of approved design with steel screws and rawal plugs etcetra complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) dia. ISI marked PVC (Poly venyl chloride) clamps make of Finolex/ Relpipe (Reliance)/Supreme of approved manufacture of approved design with steel screws and rawal plugs etcetra complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and placing three layered PVC (Poly Venyl Chloride) water storage tank ISI marked 12701 (Twelve thousand seven hundred one) Sintex/Supreme/Finolex make tripple layer and of having capacity 2000 ltr. ( Two thousand liters) tank complete in all respects, with necessary fittings including over flow pipe ball valve, scour pipe, with polythene float valve, PVC cover with locking arrangement including providing pads of sizes as required for inlet and outlet complete as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing ISI marked PVC (D-PLAST ) cowl complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including fixing with approved adhesive and carriage of materials within all leads, lifts and other incidental. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. 150mm (One hundred fifty millimeters) nominal bore/ diameters.

Providing and fixing ISI marked PVC (D-PLAST ) cowl complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including fixing with approved adhesive and carriage of materials within all leads, lifts and other incidental. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. 110mm (One hundred ten millimeters) nominal bore/ diameters.

Providing and fixing ISI marked chromium plated grating of superior quality or floor ,gulley or nahani trap complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including fixing with approved adhesive and carriage of materials within all leads, lifts and other incidental. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government. 110mm (One hundred ten millimeters) nominal bore/ diameters.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (one cement isto four coarse sand) C.I. cover with frame (light duty) 455x610 mm( four hundred fifty five into six hundred ten millimetre) internal dimensions, total weight of cover with frame to be not less than 38 kg (thirty eight Kilogramme) (weight of cover 23 kg ( Twenty three killogramme ) and weight of frame 15 kg ( Fiftten killogramme), R.C.C. top slab with 1:1.5:3 mix (one cement isto one & half Fine sand isto three graded stone aggregate 20 mm ( twenty millimetre ) nominal size), foundation concrete 1:5:10 ( one cement isto five fine sand isto ten graded stone aggregate 40 mm ( forty millimetre) nominal size), inside plastering 12 mm (Twelve millimetre ) thick with cement mortar 1:3 (one cement isto three coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc.complete as per standard design:Inside dimensions 455x610mm (four hundred fifty five into six hundred ten millimetre and 45 cm ( forty five centimetre) deep for single pipe line :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (Seven point five) complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including fixing with approved adhesive and carriage of materials within all leads, lifts and other incidental. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government

Lovish Bhardwaj

Vivek Thakur