Provision of Motivational Hall under AGE B/R-I at Mil StnYol

Amount

Excavation in trenches n exc 1.50 metre wide & n exc 1.50 metre in depth for foundation etc or for shafts, wells, cesspits manholes, pier holes etc n. exc 10 Sqm on plan n exc 1.50 metre in depth and getting out in any type of soil, complete all as specified and directed.

Surface dressing n exc 15 cm deep in any type of soil, complete all as specified and directed.

Surface excavation not exceeding 30 cms deep and averaging 15cms deep and getting out in any type of soil, complete all as specified.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc. 25cm thick each layer of soil, complete all as specified and directed.

Removing excavated material to a distance exc. 500m but not exc 1.50 KM and depositing where directed at a level not exc. 1.50m above the starting point, complete all as specified and directed.

Plain cement concrete 1:4:8, type D-2, using 40mm graded mechanically crushed stone aggregate as in foundation, filling and mass concrete, complete all as specified and directed.

Reinforced cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, all as specified.

Reinforced cement concrete 1:2:4 type B-1, ( using 20mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts, all as specified.

Reinforced cement concrete 1:2:4 type B-0, (using 12.5mm graded crushed stone aggregate) as in chajjas all as specified.

Reinforced cement concrete 1:2:4, type B-1 using 20mm graded crushed stone aggregate as in beams, cantilevers, bressummers, lintel over 1.50m span, complete all as specified and directed.

Reinforced cement concrete (nominal mix) M-15, type B-1 using 20mm graded crushed stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, for roughly finished flat surfaces of concrete, all as specified.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, for roughly finished square, rectangular or polygonal surfaces of concrete, all as specified.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. For fair finished flat surfaces of concrete, complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) in rough finished flat surface of concrete, complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge

Mortice latch 100mm with two levers (vertical type), bras body and fixed complete all as specified and directed.

M&L WPC (Wood Polymer Composit) Double Prelam Door Frame (Chowkhat) of Size 120mm x 50mm with a wall thickness of 5mm(+/- 0.25), made out of extruded 5mm(=0.25) mm thick PVC Sheet of Density 600kg/cbm manufactured y an ISO 9001-2015 certified company and by joining 3 Nos heat moulded PVC Sections. The high section of size 35 x35 mm shall be maid from plain colour PVC sheet of 5mm(=/- 0.25 mm) thickness. The inside section will be covered with 5mm thick PVC sheet'C' shape covering section of size 120mm x 50mm. At centretop position 5mm(+0.25mm) thick 50 x50 x50 mm pattam section should be pasted with solvent cemen adhesive to make double pattam of frame. The frame shall be mitre cut at two corners & joined with 4 nos of 150mm long 'L' brackets of 19 x 19 mm MS square, Tube or fusion heat welding process. The two vertical door frames are to be reinforced with 25 x 25 mm MS square Tube of 19 gauge throughout the frame. The Door Frame shall be fixed to the wall using 8/100mm fischer screws. A minimum of 4 nos of screws to be provided for each vertical member & minimum 2 Nos. for horizontal member etc. complete as per manufacture's specification & direction of engineer-in charge.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of solid core single Leaf Flush Door of 25mm thickness, lipped with 15mm (5mm x 3) thick x 30 mm width on one stiles and top rails & 10mm (5mm x 2) thick x 30 mm width on the other stiles & bottom rails. The inner panel Laminated with 2mm thick termite proof, water proof & fire resistant moulded PVC sheet with 2,4,6 raised panel design in different plain &/or prelam colors on one side after routing the mouldd design on flush door & 2mm plain and/or prelam PVC sheet on other side using rubber based adhesive on flush door & solvent cement adhesive on the lipping etc. complete as per direction of Engineer-in-charge, manufacture's specification and drawing.

Sheet glass 3mm thick ordinary quality and glazing with oil putty/wooden beads in squares, not exc. 0.5sqm in each pane, complete all as specified and directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks of glavanised wire staple fixed with stainless steel wire staples, fixed, complete all as specified and directed.

Extruded aluminium alloy handles (ISI marked), fabricated type, anodised, of size 150mm, complete all as specified and directed.

Butt hinges (ISI marked), medium weight, cold rolled, mild steel 100mm long, fixed, complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 250mm with lipping frame to match, complete all as specified and directed.

Fly ash brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed.

Brick work with old size fly ash bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 (1 cement : 4 coarse sand), all as specified.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe.410-W Gde E-250, quality A, steel work, complete all as specified and directed.

Mild Steel framed work as Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete, conforming to Fe 410 Gde E-250, complete all as specified and directed

Rolled mild steel work as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates. conforming to grade Fe.410-W Gde E-250, quality A, steel work, complete all as specified and directed.

Applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall with two corrugations side lap, fixed with self tapping screws and washers, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Designed plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets or metal frame work and reinforced with GI wire mesh with complete GI metal frame work for seamless ceilling comprising of GI permeter channel 0.55mm thick with two unequal flanges of 20mm and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.90mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each lips of 10.50mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre for flat and curved surface of ceiling, complete all as specified and directed by Engr-In-Charge. Note:- Design and shape will be approved by GE.

S&F false ceiling of Non asbestos (Designer) 4mm fibre cement building boards, manufactured from homogeneous mixture of cement, quartz and cellulose and cured with high pressure steam using auto claving process confirming to IS-14862, of size 600 mm x 600 mm x 4 mm thick fixed over and including anodised aluminium powder coated (minimum thickness of powder coating 50 micron) snap grid frame work of T section (main & cross member) of size 25 mm x 25 mm x 1.5 mm thick in square pattern of grid size 600mm X 600mm . The aluminium fram work will supported on side wall with the used of aluminium 'L' section of size 25 mm x 25 mm x 1.5 angles etc. Snap grid shall be supported with hangers of 4 mm dia Galvanised iron wire adjusting level fixed to roof slabs / truss etc by means of ceiling cleats made out of Galvanised iron flat of size 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long complete all as specified directed by the Engineer-in-Charge.

Plain cement concrete M-15, nominal mix, type B-2, using 40mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5cm deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), complete all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).

Treating the backfill in contact with foundation at the rate of 7.5 litres of antitermite emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

Treating the top surface of filled earth at the rate of 5 litres of antitermite emulsion per square metre of surface complete all as specified and directed.

Treating the soil under plinth protection at the rate of 5 litres of antitermite emulsion per square metre of surface area complete all as specified and directed.

Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering all as specified and directed.

Plain cement concrete 1:4:8, nominal mix, type D-2, using 40mm graded mechanically crushed stone aggregate as in sub base, 100mm thick, surface finished even and fair, complete all as specified and directed.

Plain cement concrete M-15 (nominal mix), 30mm thick type B-1, using 20mm graded mechanically crushed stone aggregate as in flooring, finished even and smooth without using extra cement all as specified.

Mat finish (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.06 Sqm but not exc. 0.11 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed.

Vitrified ceramic tiles light shade, 10mm thick (Square/ rectangular) area of each tile exc. 0.18 Sqm but not exc. 0.36 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand) complete, all as specified.

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.18 Sqm but not exc. 0.38 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand), including necessary cutting and waste as per site requirement, complete all as specified and directed by Engr-In-Charge. Note:- The size, shade and design will be approved by GE.

Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing

PVC sheet fillet 5mm thick of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (10mm thick first layers and 5mm thick 2nd layer), mixed with WPC @ 3% by weight of cement on fair faces of brick walls or on concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified and directed. Note:- water proofing compound shall be measured and paid seperately.

Supply only intergal water proofing compound, complete all as specified and directed.

Material and Labour for waterproofing of exterior walls, including applying two coats of acrylic polymer modified high performance coating (Smartcare Ultra Block 2k) and providing 15mm thick cement plaster in CM 1:4 finished even and smooth. The treatment shall be done from ground level.

Rendering cement plaster 15mm thick in two layers (first layer 10mm thick and second layer of 5mm thick) in cement mortar 1:6 (1 cement : 6 coarse sand) on other than fair faces of brick wall or stone masonary surfaces, surface finished even and smooth without using extra cement, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of wall to prepare the surface even and smooth and finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), complete all as specified and as directed.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over 2mm thick plaster of paris putty including preparation of surface, complete all as specified and directed.

TMT steel bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips, complete all as specified and directed.

TMT steel bars 5 to 10mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips as in stirrups, spacers and binders, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors bore 110mm, complete all as specified and directed.

Plain cement concrete M-15 nominal mix, type B-1 using 20mm graded mechanically crushed stone aggregate as in surface channel and drains, complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc., complete all as specified.

Add or deduct for each 25 mm girth or part thereof over or under 30cm for forming fair finished drain or channel in cement concrete, complete all as specified.

Plain cement concrete M-15, nominal mix, B-0 using 12.5mm graded mechanically crushed stone aggregate as in lintels upto 1.50 metre clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, chamfered angles and throating, complete all as specified and directed. Note :- (i) The unit rate include for use of form work (straight or curved).

Concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, in plain cement concrete M-7.5, nominal mix, type D-2 using 40mm graded stone aggregate, for bore of pipe 150mm. (For width and depth of PCC bed - refer preamble (a) (i) (ii) on page 391 of SSR Pt-II).

Reinforced concrete pipes, class NP3, laid and jointed complete with collars, bore of pipe 150mm (Internal dia), complete all as specified and directed.

Precast cement concrete M-15 (1:2:4) nominal mix, type B-1 (using 20mm graded mechanically crushed stone aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set in cement mortar 1:4 (1 cement : 4 coarse sand), all as specified.

Supplying and laying of CPVC pipes, 25mm outer dia, SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying floors, complete all as specified and directed.

Supplying and laying of CPVC pipes, 20mm outer dia, SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying floors, complete all as specified and directed.

Supplying and fixing brass Elbow dia 20mm, complete all as specified and directed.

Supplying and fixing brass Tee dia 20mm, complete all as specified and directed.

Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions complete, all as specified.

Bib taps, fancy type 15mm bore, cast copper alloy with crutch or butterfly handle, screwed down, chromium plated screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

PVC (SWR) floor trap, plain with grating including jointing with solvent cemen in PCC 1:2:4, dia of outlet 75mm, all as specified.

PVC connection 15mm size with PTMT nuts at both end 450mm long and fixed, all as specified.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity (cylindrical vertical with closed top) 4 layered, hoisted and fixed in position including PVC float ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line, complete all as specified and directed.

Mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed ballusters walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165, complete all as specified and directed.

Vitreous China wash down water closet (pedestal pattern), snow white, including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC coloured seat cover black closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device and chromium plated jet including 15mm dia PVC connection 600mm with CP brass coupling nuts and PVC washers at both ends, fixed, including 32mm dia PVC long bend flush pipe 90cm long pipe and fixed, complete all as specified and directed

Health Faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 Meter Long flexible Tube & ABS wall Hook including making connection and fixed, complete all as specified

Supply and fixing PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve, float and handle with brackets including 32mm dia PVC long bend flush pipe 90cm long snd 15mm dia PVC connection 600mm with CP brass coupling nuts and PVC washers at both ends, fixed, complete all as specified and directed.

Vitreous china urinal, full stall type of approved size white colour with waste coupling of PTMT (half or full threaded) minimum weight 32mm-45gms/40mm-60gms, having urinal spreader for fixing with 15mm dia pipe (Minimum weight 60 gms) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement: fixing automatic flushing cistern with brackets, flush pipe PVC connections 15mm size with CP brass coupling nuts of length 450mm, grating and union for discharge pipe, complete all as specified and directed.

Centre hole Mixer for mixing hot & cold water, chromium plated, with 450mm braided connection pipe (withot pop-up) screwed down for iron pipe of 15mm dia and fixed to wash hand basin, complete all as specified and directed. Cate No F2002461 of Cera or equivalent in makes specified in Appendix C here in after.

Wash hand basins, Vitreous China, counter Table top (Oval shape) of size 560 x 405 x205mm snow white, fixed with new brackets with and including cutting for and pinning on ends of brackets, fixed, 450mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, waste pipe of polythylene of low or high density or PVC of 32mm dia including, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed, complete all as specified. Make JS2030103 of Cera or equivalent in makes specified in appendix C

Soap dish, chromium plated, fixed to plugs with chromium plated, brass screws, complete all as specified and directed.

Aluminium anodised, tubular towel rail, 20mm dia, D type, 60cm long without lower hangers, complete all as specified and directed.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, fixed with chromium plated brass screws, complete all as specified and directed.

Hardcore of broken stone or boulders of gauge not exc. 63mm deposited, spread and levelled in layers not exc. 15cm thick, watered and rammed to a true surface, complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

Granite 20mm thick (table rubbed and polished) in steps, jambs, pollars, window-cills, cooking or WHB platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, laid over and including 15mm thick screed bed in cement mortar (1:6), including necessary cutting and waste as per site requirement pointed in white or coloured cement to match, complete all as specified and directed by Engr-In-Charge.

Rounding to edges of stone slabs of any type one edge, such as in steps cooking platform, cill of window and other simillar situations, complete all as specified and directed.

2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed, complete all as as specified and directed.

S&F Prelaminted board 18/19mm thick interior grade prelaminated both side with decorative choice lamination, fixed with screws to timber frame work as on wall panelling cup boards shutters/shelves (sliding or fixed), complete all as specified and directed.

Extra over rates of 18/19mm thick block board or veneered particle board/ prelaminated board for external teak wood lipping, 6mm thick fixed with nails, complete all as specified and directed.

Continuous (piano) hinges, mild steel, bright finish or electrogalvanised Width of flaps (when open) in 40mm, complete all as specified and directed.

Extruded aluminium alloy handles (ISI marked), fabricated type, anodised, of size 75mm, complete all as specified and directed.

Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed, complete all as specified and directed.

Point wiring with 1.50 Sqmm copper conductor FRLS (Multi strand) PVC insulated ISI Marked unsheathed cable in and including concealed PVC conduit, ISI marked of suitable size with all fittings/ accessories such as bends, cross, elbow, tees etc. of suitable size and also including PVC insulated ISI marked unsheathed 1.50 Sqmm copper multistranded conductor FLRS as phase, neutral and earth wire connected to common earth dolly and including concealed MS pressed steel of suitable sizes (modular sunken box) terminal boxes made from 1.60 mm thick sheet for mounting of switches, sockets, fan regulators, light fittings etc. and modular cover plate as top cover for one light point controlled by one way switch complete all as specified and directed. Notes:- (i) Wiring colour code i.e Red/Yellow/Blue for phase, Black for neutral and Green for earth shall be maintained. (ii) Point wiring is considered for modular switches and sockets. Rate of metallic sunken box and other connected accessories required for modular point wiring included in quoted rates. (iii) Rate of modular switch and sockets will be paid seperately under relevant item. (iv) Rate of cutting chases, cement plaster, white wash and making good as existing surface included in quoted rates.

All as per item No 95 above but for one exhaust fan point, ceiling fan controlled by one way switch complete all as specified and directed.

All as per serial item No '95' above, but for one 3 pin 5 Amps socket outlet on the independent board with 1.50 sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 1.50 sqmm stranded copper conductor cable as continous earth wire, complete all as specified and directed.

All as per item No 95 above but for 3 pin 5 Amp socket outlet on same board with 1.5 sqmm multi stranded copper conductor 1100 volts grade FRLS PVC insulated sheathed cable complete all as specified and directed.

All as per serial item No '95 above, but for 5 pin 15 amps socket outlet on independent board with 2.50 Sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 2.50 Sqmm stranded copper conductor cable as continuous earth wire, complete all as specified and directed.

S & F for modular switch, 6A one way, single module, complete all as specified and directed.

S & F for modular switch 16A one way, single module, complete all as specified and directed.

S & F for modular socket for 6A 2/3 pin combined, 2 module, complete all as specified and directed.

S & F for modular socket for 6A/16A 5 pin combined, 2 module, complete all as specified and directed.

Supply and hanging ceiling fan including fan regulator step flush type speed controllor with complete fixing arrengement of size 1200 mm sweep, 230 V, air delivery 210 CFM with service value 6 BEE, 5 star rated with brushless direct current motor (BLDC) including provision of copper multi stranded PVC insulated 1100 volts grade three core flexible cable for main connection with existing ceiling rose at point wiring complete all as specified and directed by Engr-in-Charge

S&F LED tube light fitting decorative type 1x 20 W, 230V, with driver LED lighting fixture with extruded polycarbonate, environment friendly, energy efficient ready to use complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size, complete all as specified and directed.

S&F 20 watt emergency batten 4 feet, shatter resistant, cool day white, 6500k, Inverter batten for home, atleast 4 hours of battery backup with overcharging protection, complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high output diffuser 2 feet ,10 watt, 6000 K, 220 volts, AC decorative type with extruded polycarbonate having efficiency 120 lumens /watt warm white with driver holder including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 36 watt, 220 V AC recessed/surface type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as required at site, complete all as specified and directed by Engr - in - Charge.

Supply and fixing of LED security light fitting 45 Watt, 230V, AC, outdoor type with high pressure die cast aluminium housing with street optic lens and glass diffuser for uniform light distribution and inbuilt surage protection device (SPD) and heat resistant complete with driver, street light bracket made out of GI pipe 32/40mm dia medium grade GI pipe minimum 1.50m long including fixing with 02 Nos MS clamps made out of flat iron of size 30mmx5mm with nuts, bolts and washers including painting with impact and corrison resistant including thermal management in multiple optics complete with IP 65/66 protection 6500K, complete all as specified and directed by Engr-In-Charge.

Supply and fixing Exhaust fan, Steel body, single phase, 230 volts, 300 mm sweep including grouting the ragged bolts in wall, fixing the frame on the exhaust side and connecting up with PVC insulated three core 1.50 sqmm copper cable from ceiling rose to exhaust fan, complete all as specified and diercted.

M & L for ceiling rose 65 x 50mm three terminals, fixed, complete all as specified and directed.

Supply and installing electric water storage heater (Geyser) ABS body type of 25 litre capacity with rated power 2 KW, BEE, 5 star rated, vertical type, thermally insulated Mild steel tank with glass line coating inside the tank alongwith glass lined incoloy heating element with anti corrosive magnesium anode, NRV, thermostate, indicators and temperature adjustable knob including steel braided flexible connection for pipe of size 15mm dia bore GI hexagonal adopters/Nuts on both side of inlet (cold water supply) and outlet (hot water supply) and including provision of wall mounting arrangement and mounting on wall with suitable size of anchor bolts with complete connection of water including testing after installation, complete all as specified and as directed by Engr-In-Charge.

S & F for MCB SP 6 to 32 amps 240 Volt,10 KA, 'B' series, complete all as specified and as directed.

S & F for MCB SPN 32 to 40 amps 240 Volt,10 KA, 'B' series, complete all as specified and as directed.

S & F of sheet metal enclosures distribution boards, double door, VTPN, 415 volts 4 ways, as per IEC 61439-3, degree of protection IP-43 (one incoming three phase & twelve out goings single phase) for MCCB & MCB,s comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed including and comprising of the following:- (a) MCCB FOUR POLE 125 amps, AC, 415 VOLTS 25 KA=01 No (for incoming). (b) MCB SP 06- 40 amps = 12 Nos (for outgoings) complete with 250 amps fully insulated copper bus bar for each phase and neutral link, prefitted masking sheet fixed flush in wall including chases wall for fixing DB, complete all as specified and diercted. Note :- (i) The DB shall be VTPN series of Make : Schneider or techno Equivalent in make of L&T/ ABB/legrand (ii) Connection of the MCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble properly crimped (iii) All the vacant holes of the DB shall be provided with blank plates of appropriate size. (iv) Double continuous earth wire shall be provided for each three phase DB from earthing mains duly. (v) Cutting chasing shall be part of job at no extra cost

S & F MCCB four pole 100 amps adjustable type, 415 volts, 50 Hz, breaking capacity, 25 KA including making all connections using bottle /pin copper thimbles, complete all as specified and diercted.

Sheet metal enclosures factory made flush fixed for DBs when MCBs to be used, triple pole and neutral (double Door powder coated), 4 way, 240 volts with 200 Amp rated bus bar, complete all as specified and directed.

M & L for submain wiring in and including PVC conduit 1.8 mm thick, 25 mm dia with two run of PVC insulated, unsheathed multistranded copper conductor of 6 sqmm (FRLS) and one run of PVC insulated, unsheathed multistranded copper conductor 6 sqmm (green in colour) for earth continuity conductor and connected to common earth dolly with thimble etc, complete all as specified and directed. (Two run of 6 sqmm plus one run 6 sqmm of earth wire will be measured as 1RM). Note: (a) Insulation test of point wiring to be carried out on completion of work. (b) Proper colour coding is to be maintained. (Ph-Red, N-Black,Earth- Green) (c) Two runs of single core cable with one run of earth cable and suitable size of conduit shall be measured as one RM. (d) Cutting chases for sub main wiring concealed PVC rigid conduit shall be deemed to be included in the quoted rate of item.

Supply, installation, commissioning and testing bus bar chamber LT Panel factory made Outdoor type, CPRI approved, size 0.45m x 0.75m x 0.4m deep, fabricated out of 3.15 mm thick mild steel sheet and vermin proof with neoprene gasket having front opening and locking arrangement with IP-54 protection as per IS-8623, duly powder coated (internally and externally) for 415 V, 3 phase, 4 wire having aluminium bus bar of 200A rating duly drilled holes for connections, RYB insulated with different colour code and sleeved insulators complete prewired and copper cable connection with all incoming and outgoing cable connection with suitable size of lugs and glands including one no MCCB with adjustable thermal and fixed magnetic release of capacity of 160A, 415V, 36 KA, 4 pole, mounted on angle iron frame of size 40x40x6mm, 0.40m above ground level and 0.40m embedded in PCC 1:2:4 blocks of size 0.30m x 0.30m x 0.50m = 04 Nos, duly painted with two coats of synthetic enamel paint complete all as specified and directed by Engr-In-Charge.

Supply and fixing of LED security light fitting 60 Watt, 5700K, outdoor type with high pressure die cast aluminium housing with street optic lens and glass diffuser for uniform light distribution and inbuilt surage protection device (SPD) and heat resistant complete with driver, connecting up with driver three core flexible copper conductor cases of 1.5 Sqmm size, street light bracket made out of GI pipe 32/40mm dia medium grade GI pipe minimum 1.50m long including fixing with 02 Nos MS clamps made out of flat iron of size 30mmx5mm with nuts, bolts and washers including painting with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete K=6500K, complete all as specified and directed by Engr-In-Charge.

S & F Weather proof street light junction box made of FRP or MS sheet of size 20cm x 20 cm x 15cm including one MCB SP 6 Amps and connecting terminals 4 way including necessary clamps made out of flat iron with nuts, bolts suitable for fixing on steel poles all as directed.

Supply and erecting Steel tubular swaged poles type 410 SP-31 (9.0 metre long) complete with base plate 8mm thick welded with pole, finial taper plug, bolt, nut and screws as specified complete all as specified and directed including following: (a) Excavation in trenches in any type of soil not exc 1.5 m wide and not exceeding 3.00 mtr depth, Returning filling in including spreading, levelling, watering and well ramming in layers not exc. 25cm thick each layer and removal of surplus soil upto a dispance not exc 50m. (b) PCC 1:4:8 type D-2 in foundation filling and mass concrete of sectional size 600mm x 600mm x planting depth 1.80m, (C) PCC 1:2:4 type B-1 as in plinth block/collar above Ground level of size 300mm high and 450mm dia, (d) One coat of bituminous black paint internally and externally for portion embedded in PCC upto planting depth and two coats of aluminium paint on one coat of red oxide primer on surfaces exposed to view (d) Making 30cm wide strips (total 5 Nos) with white and black paint alternately on external surface above PCC benching including numbering with black paint (e) Drilling two nos holes to pole as directed.

Mild steel galvanised tubing light grade 50mm dia with all fitting; laid in trenches, across road or on pole for protection of cable, complete all as specified and directed.

Boring holes under roads, pavement, hardstanding by trenchless technology using ultrasound technique including supply and inserting HDPE pipe 100 mm bore suiatble for 0.4 mpa working pressure all as directed.

S & F MCCB four pole 125 amps adjustable type, 415 volts, 50 Hz, breaking capacity, 16 KA including making all connections using bottle /pin copper thimbles, complete all as specified and diercted.

Supply and laying in trenches/through pipes or bore in road crossings/paths/drains/ ducts/floors/along poles/walls/ ceilings/ equipments etc. Cable Under ground, Heavy duty, armoured, XLPE insulated with stranded aluminium conductor, 10 sqmm x 2 core, 1100 Volts grade, complete all as specified and diercted.

Supply and laying in trenches/through pipes or bore in road crossings/paths/drains/ ducts/floors/along poles/walls/ ceilings/ equipments etc. Cable Under ground, Heavy duty, armoured, XLPE insulated with stranded aluminium conductor, 25 sqmm x 4 core, 1100 Volts grade, complete all as specified and diercted.

Sand cushioning to under ground cables, 8cm thick layer before laying and testing the cable and 15cm thick after laying and testing of the cable in trenches complete all as specified in Clause 19.75 of MES SSR 2009 Part-I and directed by Engr-in-Charge.

Supply and laying un-reinforced precast concrete cable cover Class LV, Type I, flat, size 250 mm x 150mm x 40mm all as specified and directed by Engr-In-Charge.

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground to a depth not less than 2.25m below normal ground level with top edge of earth plate at a depth not less than 1.50m below ground level, earth plate surrounded by 15cm thick packed layer of charcoal and common salt alternatively upto 90cm and connected with and including galvanised iron strip 25mm X 4mm (as earth lead strip), by means of bolts, nuts, check nuts and washers of GI pipe 15mm bore light grade for protection from earth plate up to testing point for protection of strip, 20mm bore GI pipe medium grade for water with wire mesh and funnel for watering including necessary excavation and earh work, PCC chamber 1:3:6 type C-2 with 40mm thick cover of rainforced cement concrete M-15 reinforced with XPM (weight not less than 4 kg/Sqm) and frame of angle iron 40x40x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape and and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50m, complete all as shown in electrical plate No. 03 of MES Schedule Part-I, complete all as specified and directed. Note:- (i) RCC pit cover shall be precast of RCC 1:2:4 type B-1, reinforcement with 8mm TOR steel @ 100 c/c in lieu of CI cover and the rate includes in the unit rate of item. (ii) Earth electrodes shall be protected upto test point using necessary arrangement with suitable size GI pipe upto 7.50m and the rate includes in the unit rate of item. (iii) Earth pit chamber and RCC cover shall be painted with red paint over a primer coat and rate includes in the unit rate of item.

Mild steel galvanized iron water tubing 25mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor, complete all as specified and directed.

Gun metal, globe or gate valves, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 25mm bore iron pipe or for unions and fixed complete, all as specified.

Supplying & laying in trencies Polyethylene (PE-AL-PE) 25mm outer dia compositc pressure pipes includin all Crimp type internal sealing Plastic-Metal Composite fittings (such as elbows, tee, reducers, etc.) complete all as directed.

M/S AMAN ENTERPRISES (BID ID -3465640)

KISHAN CONTRACTOR (BID ID -3473041)

M/s R S Construction (BID ID -3473463)

Eshaan Construction Co. (BID ID -3473748)