SPL REPAIRS TO STAGE AND PUMP HOUSE, BOUNDARY WALL, REPLACEMENT OF ASBETOS SHEET ROOF BY GALVALUME SHEET ROOF AT KV KANNUR

Amount

Demolition of cement concrete (unreinforced) in any description not otherwise specifically provided for as in coping, drains etc complete all as specified and directed.

Demolition of brickwork or stone/ boulder/laterite masonry, built in cement mortar including all quoins, arches, pillars, etc, and removing rubbish outside MD land complete all as specified and as directed.

M&L for laterite stone masonry, regular coursed, well bonded bedded and solidly hearted built in cement mortar 1:6 complete all as specified and as directed.

All as per Sl No. 3 here-in-before, but except laterite stone (Laterite stone obtained from demolition under item No 2 will be reused) complete all as specified and directed.

M&L for cement concrete 1:2:4, Type B1 (using 20mm graded stone aggregate) as in benching, stops of manhole, coping etc including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for rendering 15 mm thick cement plaster on fair faces of brick/ stone masonry surfaces in cement mortar 1:4, finished even and smooth without using extra cement complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for barbed wire fencing complete all as specified and directed.

S&F in position angle iron posts and struts split at bottom, cut to shape including providing flat iron for securing with necessary welding, drilling, bolting or riveting complete all as specified and directed.

M&L for volumetric and nominal mix cement concrete 1:2:4, Type B1, grade M-1, using 20mm graded stone aggregate including necessary form work etc complete all as specified and directed.

M&L for preparation of new steel/iron surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide Zinc Chrome primer complete all as specified and directed.

S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing's and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and directed. Note : Each line wire to be measured

M&L for preparing new plastered wall surfaces and applying one coat priming with alkali resistant priming paint and applying two coats of cement paint complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and directed

M&L for Screed bed or bedding layer of mortar 1:4, 15 mm thick for laying floor finishes complete all as specified and directed

M&L for Vitrified Ceramic tiles of size 600 x 600 mm x 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured light shade cement to match complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

M&L for rendering cement plaster 10mm thick with cement mortar (1:4) on stone surfaces as backing coat finished rough to receive tiles complete all as specified and directed.

M&L for Vitrified Ceramic tiles of size 600 x 600 mm x 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertical surface skirting etc, set and jointed in neat cement slurry and pointed in white or coloured light shade cement to match complete all as specified and directed

Taking down chowkats or frames with shutters any description not exceeding 1.5 Sqm each (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkats or frames with shutters any description exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from the frame) complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge complete all as specified and directed.

S&F Powder coated anodised aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, metered and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge complete all as specified and directed.

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge.

S&F 3mm thick sheet plain glass one side frosted, ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm in each pane with putty or fixed with beads complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

Cutting holes in brick work built in cement mortar or cement lime mortar and stone walls built in lime mortar, exc one brick but n.exc two bricks for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed

S&F flat iron hold fast and similar small articles similar articles conforming to Fe-290 Gde E-165 complete all as specified and directed

M&L for second class hardwood, plain, solid straight chowkats & frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints including preservative treatment complete all as specified and directed.

M&L for second class hardwood plain, framed, panelled shutters 30 mm thickness (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed.

M&L preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer complete all as specified and directed.

S&F 200mm Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and directed.

S&F 100 mm size Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and directed.

S&F 150mm extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 150mm Floor door stopper of brass body and tongue, anodised with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F Mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc. and similar work conforming to Fe-290 (Gde E- 165) complete all as specified and directed.

Taking down cement or cement lime plaster on brick/stone walls or in ceiling surfaces including racking out joints hacking for key scrubbing down with water etc and removing rubbish outside MD land complete all as specified and as directed.

M&L for rendering 15 mm thick cement plaster on fair faces of brick/ stone masonry surfaces in cement mortar 1:6 complete all as specified and directed.

M&L for complete removal of existing treatment on wall surfaces and applying one coat of wall primer (water thinnable/solvent thinnable) , 3 mm thickness wall care putty over plastered surface to prepare the surface even and smooth, applying one coat priming with alkali resistant priming paint and applying two coats of distemper oil emulsion complete all as specified and directed.

M&L for preparation of new wall surfaces by sanding the surfaces and applying one coat of wall primer (water thinnable/solvent thinnable) , 3 mm thickness wall care putty over plastered surface to prepare the surface even and smooth, applying one coat priming with alkali resistant priming paint and applying two coats of distemper oil emulsion complete all as specified and directed.

M&L for complete removal of existing treatment on external wall surfaces, providing and applying 1 mm thickness wall care putty over plastered surface to prepare the surface even and smooth and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed.

M&L for preparing new plastered external wall surfaces, providing and applying 1 mm thickness wall care putty over plastered surface to prepare the surface even and smooth and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings complete all as specified and directed

S&F Steel work in rectangular/tubular trusses as in purlins etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed

S&F Pre-fabricated sandwich puf panel systems for thermal insulation and energy saving fire retardant and heat proof made, pre-painted galvalume sheet with sandwiched rigid insulation, metal laminates, PIR/PUR normal density 30-40 Kgs/Cum, normal panel width 1000mm, panel thickness 50mm, 50mm concealed locking system buildings panels complete all as specified and directed

S&F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, hexagonal head with neoprene and EPDM washers complete all as specified and directed

S&F 1.25mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed

JESWIN BUILDERS (BID ID -3300463)

NRI BUILDERS AND MATERIAL SUPPLIERS (BID ID -3295028)

EURO ENTERPRISES (BID ID -3295548)

KDR CONSTRUCTION (BID ID -3292942)