Day to day maintenance and other miscellenous civil works in different T.E. buildings and staff quarters compound at Haridwar and Roorkee under SSA Haridwar.(Second Call)

Amount

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50m outside the periphery of the area cleared.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

1:5:10 (1 cement : 5 coarse sand(zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :

35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size - Kiln seasoned and chemically treated hollock wood.

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets :

20 mm dia (heavy type)

Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete.

With 12 mm mild steel U beading.

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Twin rubber stopper

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg., for doors, including cost of cutting floors ,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

With stainless steel cover plate minimum 1.25 mm thickness.

Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

40 mm thick with 20 mm nominal size stone aggregate

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,

a) Single socketed pipes- 75 mm diameter

b) Single socketed pipes-110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion.

Bend 87.5° - 75 mm bend

Bend 87.5° - 110 mm bend

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hardwood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground , all complete as per directions of Engineer-In-Charge.

With cement mortar 1:4 (1 cement : 4 fine sand).

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty:

Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm).

Cleaning of terrace/loft water storage tank (inside surface area) upto 2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of tank, including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba, all complete as per direction of Engineer-in-Charge. (The old date already written on tank should be removed with paint remover or black paint and if date is not written with the stencil or old date is not removed deduction will be made @ Rs. 0.10 per litre if during cleaning any GI fittings or ball cock is damaged that is to be repaired by contractor at his own cost and nothing extra will be paid on this account)

Cleaning of under ground sump, Over Head R.C.C. Tank (independent staging) including disposal of slit and rubbish, all as per direction of Engineer-in-Charge. The cleaning shall consist following operations:-

(i) Tank shall be emptied of water by pumping & bottom shall be cleaned of slit and other deposits. (ii) Entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water. (iii) Chlorination of RCC internal surface by liquid chlorine. (iv) The treated surface shall be dried using air jetting and all loose particles shall be removal from the surface. (v) Finally the surface shall be treated with ultraviolet radiation etc. as per direction of Engineer-in-Charge.

Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls andfloors wherever required:

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :

Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern

Providing and fixing white vitreous china water closet squatting pan (Indian type) :

Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

10 litre capacity - White

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete :

White solid plastic seat with lid

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe - 32 mm dia

Flexible pipe - 40 mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour. Weighing not less than 300 gms.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall.

15 mm dia. nominal bore

20 mm dia. nominal bore

25 mm dia. nominal bore

32 mm dia. nominal bore

40 mm dia. nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Arranging services for plumbing, masonry, Carpentary jobs for day to day maintenance of all departmental buildings i/c repair/fixing of bib cock, stop cock, pillar taps, PVC connection, shower rose, GI pipes, gully traps, joints including cleaning etc. and Removal of chockage/blockage in traps including cleaning of traps & disposal of waste material and minor repair of wooden doors and windows all complete as per direction of Engineer-in-Charge. (Note: All T&P shall be arranged by the agency except materials required which will be supplied by the department. Payments shall made on job basis for period of one month).

Providing manual assistance for miscellaneous works as per site requirement and as per direction of Engineer-in-Charge. (Note:- One day service of each labour shall be treated as one job).

Cleaning of roofs including removing algae, dust, leaves opening of rainwater pipes and their inlets, cleaning of khurras and disposal of rubbish and waste material at appropriate place inside the campus all complete as per direction of Engineer-in-charge.

Removing of chokage of floor traps, Nahani traps, water closet and associated C.I. pipe and bends to ettect smooth flow of wastes by pressure pushing, flexible wire and taking out refuse and dispose off etc. complete.

Removal of chockage / blockege in W.C. Seat including cleaning of seat & disposal of waste material all complete as per direction of Engineer-in-Charge.

Repair of existing rolling shutters by taking out and refixing the same after change of necessary parts such as spring / ball bearing etc if required i/c doing welding etc. as per the site required & as per the direction of Engineer-in-Charge. (Note: The rate includes cost of material and labour required for complete repairing).

Providing and fixing aluminium sheet 26 SWG thick on existing door shutter (Bathroom and WC doors) using nails complete in all respect and as per direction of E-In-Charge.

Repairing of aluminium doors including dismembering, replacement of cleats, fixing of tie rod, replacement of pivots, refixing of the door all complete as per direction of Engineer- in- Charge. (Note: Rate includes cost of material and labour required for the job)

"Cleaning of manhole chamber i/c interconnecting sewer line at all compound at Haridwar i/c removel of earth, silt, sludge, brickbats, garbage & other refuses,disposing them to the nearest municipal ground complete as per the direction of Engineer-In-Charge. Cleaning of manhols shall be done at a frequancy may vary as per site requirement.Note;Rate including the cost of cleaning of manhole covers and keeping the same back in position after completion of work. "

Cleaning and opening of drainage line including excavation of deposited sludge and mud and stacking the same to place as specified including all complete as per the direction of Engineer-In-Charge

Cleaning of RCC under ground tank / Over head tank of different capacity at different level by removing sludge with the help of special type sludge pump, cleaning of internal wall by rubbing with clean cloth, washing and disposal of water through pumping system and disinfecting under ground tank / over head tank by flushing with water containing bleaching powder @ 0.50 gm per litre of water all complete as per direction of Engineer - in - Charge.

Removing plantation and its roots from buildings upto all heights including dismentling and repairing plaster and masonry all complete as per direction of Engineer - in- chagre and applying chemical with name "ROUND UP" or equivilatant on the roots of plants. (Note: The rate includes arrangement of necessary scaffolding and ladders).

Fixing of threaded PVC water tank covers with threaded neck arrangement fixed with the top neck of the Water storage tank with necessary srews and fittings etc .All complete as per the direction of Engineer-In-charge.

Providing the following items/fittings approved quality confirming to IS standards as per direction of Engineer-in-Charge.

C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. - 15 mm nominal bore

C.P. brass bib cock of approved quality conforming to IS:8931: - 15 mm nominal bore.

C.P brass long body bib cock of approved quality confirming to IS standards as per direction of E-In-charge - 15mm nominal bore

G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : 20 mm nominal bore.

C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15mm nominal bore

C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

PTMT bib cock of approved quality and colour. - 15mm nominal bore, 86 mm long. Weighing not less than 88 gms.

PTMT stop cock of approved quality and colour - 15 mm nominal bore, 86 mm long. Weighing not less than 88 gms.

PTMT pillar cock of approved quality and colour . - 15mm nominal bore, 107 mm long. Weighing not less than 110 gms.

PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. - 15 mm nominal bore, 105 mm long. Weighing not less than 138 gms.

PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. - 20 mm nominal bore, 120 mm long. Weighing not less than 198 gms.

PTMT angle stop cock 15 mm nominal bore. Weighing not less than 85 gms.

PTMT swivelling shower, 15mm nominal bore. Weighing not less than 40 gms.

C.P. Pillar cock of approved quality.15mm nominal bore

Internal fittings of flushing cistern such as syphan / handles etc. all complete as per direction of Engineer-in-Charge.

PVC nahani trap

Cistern long bend

Syphon washer for Cistern

PTMT waste coupling 31/32 mm

PVC ball valve for low level cisterns

PVC cistern handle

CP shower fency type

C.P. Floor grating 110mm

PVC semi rigid waste pipe- 32 mm

PVC semi rigid waste pipe- 40mm

Brass bib cock of approved quality : 15 mm nominal bore

Brass stop cock of approved quality : 15 mm nominal bore

Gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore

Gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

Unplasticised PVC connection pipe with brass unions :

45 cm length : 15 mm nominal bore

G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required :

15 mm nominal bore.

20 mm nominal bore.

25 mm nominal bore.

32 mm nominal bore.

40 mm nominal bore.

G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall.

15 mm dia. nominal bore

20 mm dia. nominal bore

25 mm dia. nominal bore

32 mm dia. nominal bore

40 mm dia. nominal bore

Elbow:

G.I. Socket

Tank Nipple:

G.I. Tee

Credit of old dismantled unservisable material at site.

Wooden paneled / flush door shutter/ glazed shutter/ wire guage shutter of size upto 2.50 Sqm.

Brass bib cock / stop cock / Pillar cock etc.

Old unserviceable hydraulic door closer.

PVC Cistern.

Double action floor door spring.

PVC Tanks (upto 500 litres)