Construction Additional Accommodation on Govt Sen Sec School Bagsaid in Tehsil Thunag Distt. Mandi (SH C/o Building portion, WS SI site development soak pit septic tank and rain water harvesting system

Amount

Earth work in excavation for structure as per drawing and technical specification clause 305.1 i/c setting out construction of shoring and bracing removal of stumps and other deletarious material and disposal up to any lead dressing of sides and bottom and back filling in trenches with excavated suitable material ordinary soil. with in all leads and lilfts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Excavation in foundation, trenches etc. in earth work in all kinds of soil such as pick work, Jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/dewatering upto any lift, stacking the excavated soil upto any lead from the edge of excavation and then returning the stacked soil in layer when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing form work with steel plates 3.15mm(Three point fifteen millimeter) thick welded with angle iron in frame 30x30x5mm(Thirty millimeter into thirty millimeter into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and bellies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in situ-reinforced concrete and pain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge in:- Vertical surface such as walls(any thickness) and the like including attached pilasters, buttersses plinth and string courses and the like

Foundation, footing basis of columns etc. and mass concrete .

Flat surfaces such as soffits of suspended floors, roofs, landings and the like Floors etc upto any thickness.

Beams, cantilever, girders and lintels sides and soffits of beams, beam haunching, cantilevers, bressumers and lintels in any depth in all height from floor..

Columns, pillars, Posts and struts, Square, rectangular or polygonal in plan

Stair cases with sloping or stepped soffits excluding landing

Edges of slabs and breaks in floors and walls in any width.

Providing and laying cement concrete 1:6:12 (1 cement:6 sand : 12 graded stone aggregate 40 mm (fourty millimetre) nominal size and curing complete excluding cost of centring and shuttering in foundation and plinth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying cement concrete 1:4:8 (1 cement : 4 sand : 8 Graded stone aggregate 25mm (twenty five millimetre) nominal size and curing complete excluding cost of form work in foundation and plinth in breast and retaining walls etc. as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying cement concrete 1:4:8 ( one cement: four sand: eight graded/ crushed stone aggregate 40mm (Forty millimetre ) nominal size) mechanically mixed and vibrated and curing complete excluding the cost of form work in foundation and plinth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying cement concrete 1:3:6 (1 cement:3 sand:6 graded stone aggregate 40mm (fourty millimetre) nominal size) excluding cost of centring and shuttering in foundations and plinth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

C/o Dry rubble masonry in breast wall and retaining walls revetment walls and parapets etc. as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing 100mm (one hundred millimetre) diameter poly Vinyl chloride pipe in Weep holes in brick masonry/stone masonry, plain/reinforced concrete and retaining /breast walls etc. extending through the full width of the structure with slope of 1V:20H towards drainage face complete as per drawings and technical specifications and as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Back filling behind abutment, wing wall and retaining wall complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Stone soling/boulder filling dry hand packed in under floor as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying cement concrete work 1:2:4 (1 Cement:2 Sand:4 graded stone aggregate 20 mm (twenty millimetre) nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . Foundations,footings bases of columns and the like and mass concrete.

Suspended Floor roofs, landing and shelves and their support balconies, beams, girders, bressumers and contilever.

Walls (any thickness but not less than 0.10 metre thickness) including attached pilasters buttersses,plinth and string courses etc.

Providing and laying reinforced cement concrete design mix M-25 (Design mix) grade mechanically mixed and vibrated and curing excluding cost of form work and reinforcement for reinforced cement concrete work. The mix shall be designd as per requirement of I.S code and P.W.D specification. The design mix will be got approved from the Engineer - in - Charge prior to the casting . The theoritical consumption of cement fot the item shall be worked out as per approved design mix as per I.S code including carriage of materials with in all leads, lifts and other incidentals . Foundations,footings bases of columns and the like and mass concrete.

Suspended Floor roofs, landing and shelves and their support balconies, beams,girders, bressumers and contilever.

Columns, pillars posts and struts etc.

Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing.

Providing and laying reinforced cement concrete 1:2:4 (one cement : two Sand :four graded stone aggregate 20mm (twenty millimetre) nominal size mechanically mixed and vibrated to give an smooth and even surface including centring and shuttering etc upto all level but excluding cost of reinforcement in String courses, copings, bed plates, anchor blocks, plain windows sills and the like as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire up to any level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (1 cement :6 sand : 12 graded stone aggregate 20mm (twenty millimetre) nominal size at plinth level in Cement Mortar 1:6(1 cement:6 sand) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Square rubble masonary coursed with hard stone of approved quality in foundation and plinth in Retaining walls/Breast walls including rakingout joints in Cement Mortar 1:5 (1 Cement:5 Sand) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing in RCC work smooth finishing of the exposed surface with cement mortar 1:3 (1 cement : 3 sand) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Brick work using common burnt clay building bricks in Superstructure above plinth level in Cement mortar 1:6 (One Cement : Six Sand) second Class Bricks as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.upto Floor any Level

Half brick masonry in common burnt clay building bricks in cement mortar 1:3 (one Cement :Three Sand) (2nd Class Brick)in super structure above plinth level upto all floor level as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing woodwork in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position 2nd class deodar wood as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing wood work in frames of false celling partitions etc. sawn and put-up in position 2nd class deodar wood as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 35 mm (thirty five millimetre) thick including black enamelled M.S. butt hinges flush door shutters interior grade, commercial type, core of black-board construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains of cross bands and face veneers on both faces of shutters as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing panelled glazed or panelled and glazed shutters for doors windows and clerestory windows Including black enamelled iron butt hinges with necessary screws 40 mm (fourty millimetre) thick 2nd class deodar wood as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing double glazing (double glass) fixed in door, window, ventilator shutters and partition etc with PVC/neoprens gasket etc. complete glazing with glass panes of 4mm (four millimetre) thickness (weight not less than 10.00 kg/sqm. (ten kilogram per square metre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 2nd class deodar wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm (zero point five six millimetre) for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 12mm (twelve millimetre) thick 150mm (one hundred fifty millimetre) wide pelmet with 25 mm (twenty five millimetre) diametre wooden curtain rods and brackets including fixing 25x3mm (twenty five into three millimetre) M.S. flat at 10 cm (ten centimetre) Long and plugs etc. complete 2nd class indian teak wood as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing brass curtain rail with rollers stop ends and brackets in pelmets instead of wooden curtain rod 25 mm (twenty five millimetre) dia and brackets of first class deodar wood (actuallenght) of rails of be measured as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing M.S. plain grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing 40x3 mm (fourty into three millimetre) flat iron hold fast 40cm (fourty centimetre) Long including fixing to frame with 10mm (ten millimetre) diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm (thirty into ten into fifteen centimetre)1:3:6 ( 1 cement : 3 sand: 6 graded stone aggregate 20mm (twenty millimetre) nominal size as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 75 mm x 60mm (seventy five millimetre into sixty millimetre) rounded hand rails in straight length complete in 2nd class deodar wood as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete.300x16mm (three hundred x sixteen millimetre) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodized aluminum tower bolts (barrel type ) anodized trans parent or dyed to equired shade and colour with screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 250x10mm (Two hundred fifty into ten millimeter)

150x10mm (One hundred fifty into ten millimeter)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 125 mm (One hundred x twenty five millimeter)

100 mm (One hundred millimeter)

Providing and fixing 100mm (One hundred millimeter) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 150 mm (one hundred fifty millimetre) bright finished hard drawn hooks and eyes as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 115mm (one hundred fifteen millimeter) oxidized M.S heaps and stapples (safety type) with necessary screws etc complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 150 mm (one hundred fifty millimetre) M.S. single acting spring hinges bright finished with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 19mm (nineteen millimetre) thick Commercial Board water proof shutters for up boards including fixing with nickel plated piano hinges with screws etc complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 19mm (nineteen millimetre) thick water proof commercial board in shelves/box for cup board with butt joints & fixing with nails & screws etc complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing wall paneling of 12 mm (twelve millimeter) thick pre laminated particle board (one side) of approved brand of soft wood 4x4 cm frames @60 cm center to center on both side fixing with rawl on wooden plugs and screws and showing 8 mm wide in elevation and finished teak wood beading outlay 25x12 mm deep groves of required pattern of 25x12mm(twenty five millimeter x twelve millimeter) /Cornish out to 75x60mm(seventy millimeter x sixty millimeter) of different pattern in top middle and corner joints including polishing and painting groves complete as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

White glazed tiles 6 mm (six millimetre) thick in skirting risers of steps and dado 12 mm(twelve millimetre) thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

25 mm (twenty five millimetre) thick Kota stone slab flooring 20 mm (Twenty millimetre) (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as per direction of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Kota stone slab 25 mm (twenty five millimetre) thick in risers of steps,skirting dado and pillars laid on 12 mm (twelve millimetre) (average) thick cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete as per direction of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 10mm (ten millimetre) thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 600x 600mmx10mm (six hundred millimetre into six hundred millimetre into ten millimetre) manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm (twelve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete as per direction of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

25 mm (twenty five millimetre) thick wooden flooring laid over R.C.C/C.C. slab (to be paid separately) (thinly coated with thin layer of hot bitumen blown type) @ 2.45 kg per sq m (two point four five kilogram per square metre) including fixing of wooden planks in position over wooden plugs fixed in c.c./R.c.c. floor including planning and levelling complete 2nd class deodar wood as per direction of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

40 mm (fourty millimetre) Cement concrete flooring 1:2:4 (1 cement : 2 sand:4 graded stone aggregate 20 mm (twenty millimetre) nominal size laid in one layer finished with a floating coat of neat Cement as per direction of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 0.60mm (Zero point six zero milimetre) thick preprinterd steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) micons primer coating to back coast of polyester of 5 microns over 5 microns primer coating including fixing with screws, prepainted iron J or L hooks, bolts and nuts 6mm(six milimetre) dia with prepainted limpet and rubber washer complete with all accessories as required as per specifications and as per direction of Engineer-in-Charge including carriage of materials with in all leads, liftsother incidentals.

Providing and fixing ridges or hips 60 cm (Sixty centimeter) overall with 0.60 mm (Zero point sixty millimeter) thick preprinted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat or regular modified polyester organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with preprinted iron J or L hooks, bolts & nuts 6mm(Six millimeter) dia and preprinted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm (one point six six millimetre to two millimetre) thick in eaves board/facia/soffits/ ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 15 cm (fifteen centi metre) wide 45 cm (fourty five centimetre) overall semicircular plain G.I. sheetgutter with iron brackets 40x3mm (fourty into three millimetre) size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design 0.63mm (zero point six three millimetre) thick sheet as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 150mm (one hundred fifty millimetre) dia pipes on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm (four point five kilogram per square metre) including filling the joints with approved adhesive complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing PVC Plain bend 150mm (one hundred fifty millimetre) dia on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 75mm (seventy five millimetre) PVC clamps of approved design fixed with steel screws as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Steel work welded in built up sections,trusses and framed work,including cutting, hoisting, fixing in position and applying a priming coat of red lead paint In beams joists channels, angles, tee, flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Steel work welded in built up sections,trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of red lead paint In gratings framed guard bars, ladders, railling, brackets and similar works as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Steel work welded in built up sections,trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of red lead paint In trusses and trussed purlins in buildings as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing angle iron cupboard frames manufactured from M.S.Angle iron section 25X25X5mm (twenty five into twenty five into five millimetre) thickness including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 25X25 mm (twenty five into twenty five millimetre) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm (two point five millimetre) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing calcium silicate tiles ceiling of approved quality with butt jointing and nail (Frame work and cover fillets to be paid for separately). False ceiling in combination with prepainted steel section as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

6mm (six millimetre) Cement plaster to ceiling In Cement Mortar 1:4(1 Cement : 4 Sand) as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/concrete/stone wall for interior plastering upto floor all level including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:6 sand) as per the direction of Engineer-in-Charge including carriage of materials within all leads, and lifts other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering up to all floor level includingarises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:six sand)as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering up to all floor level includingarises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:5 (one cement : five sand) as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease,dirt and other forein matter sand papering and knotting ready mixed paint with wood priming pink as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Painting two coats(excluding coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping With enamel paint other than white as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete With ready mixed priming paint brushing red lead,Red-oxide/zinc oxide chrome as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Painting two costs (excluding priming cost on new steel and other metal surfaces eith enamel paint brushin to give an even shade including cleaning the surface of all dirt,dust and other foregin matters Enamel paint other than white as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Polishing two coats with french polish on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt,dust,and sand papered smooth and including a coat of wood filler as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including t horoughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Distempering with dry distemper of approved brand and manufacture(Two coats)and of required shade on undecorated wall surface to given an even shade over and including primer coat of whiting after thoroughly brushing the surface free from mortar droppings and other foreign matter including preparing the surface even and sand papered smooth as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing plinth protection 50mm (fifty millimetre) thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm (twenty millimetre)nominal size as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing under layer for plinth protection of 75mm (seventy five millimetre) thick (unconsolidated) bed dry brick/stone aggregated 40mm (fourty millimetre) nominal size with rammed and consolidated and grouted with fine sand including preparation of ground as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Constructing course rubble dressed "U" shape open surface drain with side wall 15X22cm (fifteen into twenty two) in cement mortor 1:6 (one cement: six sand) and in side plstring with cement plaster 1:3 (one cement : three sand ) including earth work and laying 10cm (Ten Centimetre) cement concrete 1:5:10 (one cement :five sand:ten graded stone aggregate 40mm (Forty millimetre) nominal size) and 7.5cm (seven point five centimetre) cement concrete 1:2:4(one cement :two sand ;four graded stone aggregate 20mm (Twenty millimetre) nominal size) and finishing with a floating coat of neat cement and curing complete as per standard design as per the entire satisfaction and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 20 mm (twenty millimetre) nominal bore to wall ceiling and floor galvanized mild steel tube (medium grade) tube fittings and clamps including making good the wall ceiling and floors with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing PVC water storage tank of ISI:12701 marked,G.I.inlet and outlet connection,15mm (fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level:-1000 (one thousand)litres capacity. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Supplying cast iron cover with frame for manhole for frame of internal dimension 455 x 610 mm (four hundred fifty five into six hundred ten millimetre) rectangular CI cover the weight of cover to be not less than 38 kg (thirty eight kilogram) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing plythelineo-aluminiumo-polythelene(PE-AL-PE) composite pressure pipe U.V.stabilized with carbon black confirming to IS-15450-2004 water supply including clamp at one meter spacing,cutting,fixing and making good the wall etc.but excluding the cost of fittings(internal work) pipes exposed on wall.internal worko-exposed on wall. (KITEC make) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 1620 (one thousand six hundred twenty) 20 mm (twenty millimetre) OD pipe

1216 (One thousand two hundred sixteen) 16mm (sixteen millimetre)O.D.Pipe.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors,couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. (KITEC make) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. Reducing tees 1620 (one thousand six hundred twenty) x all branches

Equal tees i)1216 (one thousand two hundred sixteen)

Female branch TEE i)1216x1216x15mm (one thousand two hundred sixteen into one thousand two hundred sixteen into fifteen millimetre) thread.

Female elbows i)1216x15mm (one thousand two hundred sixteen into fifteen millimetre) thread.

Female thread connector i) 1216x15mm (one thousand two hundred sixteen into fifteen millimetre) thread.

couplers i) 1216 (one thousand two hundred sixteen).

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc complete. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm (seventy five) nominal size.

110mm (one hundred ten millimetre) nominal size.

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete icluding fixing with approved adhesives etc. 110mm (one hundred ten millimetre) nominal size. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing PVC single equal branch plain, ISI marked including fixing with approved adhesives etc. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm (seventy five millimetre) dia

110 mm (one hundred ten millimetre) dia

Providing and fixing PVC collar, ISI marked including fixing with approved adhesives etc.with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm (seventy five millimetre) nominal size.

110mm (one hundred ten millimetre) nominal size.

Providing and fixing PVC plain bend, ISI marked including fixing with approved adhesives etc. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm (seventy five millimetre) nominal size.

110mm ( one hundred ten millimetre) nominal size.

Providing and fixing PVC clamps, ISI marked of approved design with steel screws and rawal plugs etc. Complete. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm (seventy five millimetre) nominal size.

110mm (one hundred ten millimetre) nominal size.

Providing and fixing PVC floor trap ISI marked of self cleansing design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. 110 mm x 75 mm (one hundred ten millimetre into seventy five millimetre) size. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing vitreous China wash down, water closet squatting pan (Indian type W.C pan) size 580mm (five hundred eighty millimetre) (Earth work, bed concrete, foot rest and trap to be measured and paid for separately). Orissa pattern (Cera) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing vitreous china water closet(European type w.c.pan) with integral 'p' or 's' trap including jointing the trap with soil pipe in cement mortar 1:1 (1cement:1sand)(seat and cover to be measured and paid for seprately):-(Cera) Anglo indian universal closet with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

P/F PTMT coloured/white high density polyethylene/poly propylene 10 (ten) litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm (fifteen millimetre) nominal size PVC ball valve with polythene float,with push button, couplings for connections with inlet,outlet and overflow pipe, 40mm (forty millimetre) dia C.P.flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (over flow pipe to be measured and paid for seprately) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing plastic seat(solid/hollow type) and cover for wash down water closet with c.p. brass hinges and rubber buffers:-Solid type (a) white plastic seat and cover with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings extra for pair of hole for pillar tap instead of single hole (Jaquar or ESS-ESS) Flat Back 550mmx400mm (five hundred fifty millimetre into four hundred millimetre) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing vitreous china pedestal for wash basin complete recessed at the back for reception of pipes and fittings. (Jaquar or ESS-ESS) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and c.p.waste with c.I.or m.s.brackets painted white including cutting holes and making good the same but excluding fitting.(i) 470x420mm (four hundred seventy into four hundred twenty millimetre) with bowl depth 178mm (one hundred seventy eight millimetre). (Jaquar or ESS-ESS) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing CP brass toilet paper holder including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge. (Jaquar or ESS-ESS) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing 32mm (thirty two millimetre) dia C.P Brass waste for wash basin or sink with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing 32mm (thirty two millimetre) dia MI union for wash basin or sink with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing vitreous China bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with choppe hemp (weste pipe to bemeasured and paid for separately Flat back type of size 430mm x 260 mm x 350mm (four hundred thirty millimetre into two hundred sixty millimetre into three hundred fifty millimetre) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing division plate for urinals 600mm x300mm (six hundred millimetre into three hundred millimetre) virterous china including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge. (Jaquar or ESS-ESS)

Providing and fixing 600mm x450mm (six hundred millimetre into four hundred fifty millimetre)beveled edge mirror of superior glass mounted on 6mm (six hundred millimetre) thick A.C sheet or ply wood sheet and fixed to wooden plugs with C.P brass screws and washers with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing C.P brass towel rail complete C.P brass brackets fixed to wooden plugs with C.P brass 600mmx20mm. (six hundred millimetre into twenty millimetre) Thick (Jaquar or ESS-ESS) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing chromium plated brass soap dish with C.P brass brackets fixed to wooden cleats with C.P brass screws . (Jaquar or ESS-ESS) with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) nominal bore C.P. brass flush pipe/spreaders for urinal with fittings such as unions, clamps etc. (all C.P.) including cutting holes and making good the same including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 32mm (thirty two millimetre) lead waste pipe for wash basin or sink including check nut including carriage of material with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) dia C.P brass bib tap with capstan head (Jaquar or ESS-ESS) with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) dia C.P brass pillar tap with capstan head (Jaquar or ESS-ESS) with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) C.P.Brass angle valve without nuts and pipe with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 300/450mm (three hundred/four hundred fifty millimetre) length 15mm (fifteen millimetre) nominal bore P.V.C connection pipe with brass unions with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing PTMT jet spray of approved quality and colour with 1metre tube with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 100 mm (hundred millimetre) nominal dia PTMT grating round of approved quality and colour with in all leads and lifts and as per the direction of Engineer-in-Charge.

Constructing manhole with R.C.C top slab in 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (twenty millimetre) nominal size) foundation concrete 1:4:8 (one cement : four sand : eight Graded stone aggregate 40mm (forty millimetre) nominal size ) inside plastering 15 mm (fifteen millimetre) thick with cement mortar 1:3(one cement : three sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (twenty millimetre) nominal size finished smooth complete including curing and testing (i)inside size 800mmx800mm (eight hundred millimetre into eight hundred millimetre) and 500 mm (five hundred millimetre) deep including C.I. cover with frame( light duty single (seal ) pattern I) 455mmx610mm (four hundred fifty five millimetre into six hundred ten millimetre) internal dimensions total weight of cover and frame to be not less than 38 kg (thirty eight kilogram) (weight of cover 23 kg (twenty three kilogram) and weight of frame 15 kg (fifteen kilogram) A)with 200 mm(two hundred millimetre) thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (one cement : three sand )with in all leads and lifts and as per the direction of Engineer-in-Charge.

SHIV RAM