Supply, Erection, Testing& Commissioning of 132KV 2x(3+0) 1Cx800sq.mm U/G cable laying 132KV LILO Chiloda from 132KV Ranasan Vijapur line.(From prop.AP 5/0(DD+3)cable termination tower to 132KV Chiloda SS(Ckt-1 &2-Route length-1.40Km) under KSY-II.

Estimated Cost of laying of two equal lengths of FOAC (Fiber Optic Approach Cable) ( DWSM - Dual window single mode, 48F) - with installation hardware like ties / clips /

cleats, conduits, HDPE ducts, supports, fittings, accessories etc with required arrangement to lay along side of U/G cable - (Annexure-B1 (Supply) & B2 (Erection))

Estimated Cost (Supply Part) (Annexure-B1)

Sr.No. Name of Line FOAC Single Length (DWSM Nos. of such sigle length Total length of FOAC (DWSM 48F)

48F) (meter) of FOAC required (meter)+ Length of Approach cable

1 132 kV LILO Chiloda from 132 kV Ranasan Vijapur line 1580 2

Estimated Cost (Erection Part) (Annexure-B2)

Sr.No. Name of Line FOAC Single Length (DWSM Nos. of such sigle length Total length of FOAC (DWSM 48F)

48F) (meter) of FOAC to be laid (meter)+ Length of Approach cable

1 132 kV LILO Chiloda from 132 kV Ranasan Vijapur line 1580 2

Note1: Only FOAC BOQ is prepared based on input. However for OPGW BOQ, Query is given vide mail Dtd: 02.05.2025. OPGW BOQ shall be conveyed after compliance to query mail.

Following points are important from work execution perspective, same may please be noted.

i) Fiber optic approach cable (FOAC) shall be laid with 132kV cable system strictly as per approved method of construction i.e MOC. Each run of FOAC shall be of continuous length, no in between

splicing is allowed.

ii) Two to Three rings of extra loop length shall be kept buried underground at foot of both end termination tower after laying FOAC cable with 132kV cable as per MOC.

iii) FOAC cable length remain outside and above the ground level shall be 2 times the height of each termination tower at both end. Each run of FOAC cable coming out after laying in underground

section should be brought up to third cross arm of termination tower after passing it through HDPE pipes and properly tying up with tower. Also, each run of FOAC cable shall be terminated in

individual joint box on each termination tower.

iv) Balance length of each FOAC cable (i.e. Approximately half of tower height) after bringing out the FOAC cable above from ground level and up to third cross arm of termination tower, it shall be

managed in rings properly with fixing clamp arrangement to hold up it on end termination tower.

v) As per standard GETCO format of "End to End test.pdf" , after laying FOAC cable, each length shall be tested for end to end test using power meter and OTDR. Original copy of Test report duly

sealed and signed with date, name & designation of testing person, executing contractor and witnessing officer one each from telecom as well as TR/Const. nominated from respective EE(Telecom)

and EE(TR)/EE(const.) respectively, shall be submitted to under signed & one copy to respective telecom unit, invariably without fail

vi) Only after getting clearance on validity of test report submitted to this office, filed officer will take further necessary action on commercial part.

vii) DRS (Data requirement sheet) and drawing approval shall be taken for FOAC & joint box before kick starting any erection activity. The work executing contractor must have to do

correspondence on eamil to concern EE (Const.) with copy to project & engineering department, corporate office, GETCO for necessary concurrence and intimation about to start erection/laying.