Construction of Sub Treasury Office building at Nihri Distt. Mandi HP

Amount

Excavation in foundations, trenches etc.in earth work in all kinds of soil such as pick work, jumper work, blasting work, saturated soil , including chieslling or any other mixed variety of soil, dewatering and or removal of slush and other incidentals, lift up to any heights, stacking the excavated soil upto any leads clear from the edge of excavation and then returining the stacked soil in 15 cm ( fifteen centemetre) layer when required in to plinth sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as per direction of Enginer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Filling in plinth with sand under floors including watering ramming, consolidating and dressing complete as per direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Stone soling /Boulder filling dry hand packed in under floor as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing form work with steel plates 3.15mm ( three point one five millimeter) thick welded with angle iron in frame 30x30x5mm (thirty X thirty X five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and balies in any height / depth of propping and centring below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work including carriage of materials with in all leads ,lifts and other incidentals as per direction of Enginer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying cement concrete 1:4:8 (1 cement:4 sand:8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in: Foundation and plinth: as per direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other ncidentals.

Providing form work with steel plates 3.15mm ( three point one five millimeter) thick welded with angle iron in frame 30x30x5mm (thirty X thirty X five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and balies in any height / depth of propping and centring below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work including carriage of materials with in all leads ,lifts and other incidentals

Flat surfaces such as soffits of suspended floors, roofs, landing and the like floors etc. upto all thickness in all floor level including carriage of materials with in all leads, lifts and other incidentals.

Columns, Pillar posts and struts, square, rectangular or polygonal in plan in all floor level including carriage of materials with in all leads, lifts and other incidentals.

Beams, cantilevers, girders and lintels, side and sofits of beams, beam haunchings cantilevers, bressumers and lintels upto any depth / length depth in all height in all floor level including carriage of materials with in all leads, lifts and other incidentals.

Stair cases with slopping or stepped soffits excluding landing in all floor including carriage of materials with in all leads, lifts and other incidentals.

Providing weep holes in brick masonry/stone masonry/plain/RCC abutments, wing walls, return walls with 100 mm(One hundred millimeters) dia PVC pipe extending through the full width of wall/structure with slopes of 1(One)(v): 20(Twenty)(H) towards drawing and technical specification clause 614, 709,1204,3.7 as per direction of Engineer-in-charge including carriage of materials within all leads and lifts and other incidentials. The rate including octroi,royality, Malkana toll tax ,sale tax or other taxes imposed by the Goverment.

Backfilling with Granular material behind abutment,wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying cement concrete 1:3:6 (one cement :three sand:six graded stone aggregate 20 mm(twenty milimeters)size and curing complete excluding cost of form workin foundation and plinth including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying cement concrete 1:1.5:3 (1cement :1.5 sand :3 graded stone aggregate 20mm. nominal size) and curing complete excluding cost of form work and reinforcement for feinforced concrete work in as per direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other ncidentals.

Columns, Pillar posts and struts, square, rectangular or polygonal in plan in all floor level including carriage of materials with in all leads, lifts and other incidentals.

Suspendal floor,roof landing and shlavesand their sup,balconies,beams girders,breasumers and cantilevers upto including carriage of materials with in all leads, lifts and other incidentals.

Foundation footings bases of columns and thel ike and mass concrete

Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing up to all floor level. including carriage of materials with in all leads, lifts and other incidentals.

Wall (any thickness but not less then 0.1m(zero point one meter) attached pillasters,buttresses,plinth and string courses etc.from top of foundation level up to floor level

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position including cost of binding wire complete upto all floor level including carriage of materials with in all leads, lifts and other incidental charges complete in all respect as per direction and Satisfaction of Engineer-in-charge .

Second class brick masonry in common burnt clay building bricks in super structure up to all level in cement mortar 1:6 (one cement : six sand) and curing compelete including carriage of material within all leads, lifts Above Plinth Level up to all floor level.and others incidental charges complete in all respect as per direction and Satisfaction of Engineer-in-charge .

Second class half brick masonry in common burnt clay building bricks in super structure above plinth level up to all level in cement mortar 1:3 (one cement : three sand) and curing complete including carriage of material within all leads, lifts Above plinth level up to all floor level and others incidental charges complete in all respect as per direction and Satisfaction of Engineer-in-charge .

Providing 0.60mm ( zero point sixty millimeter) thick pre painted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat of regular modified polyester (RNP) organic coating of 20 (twenty) microns over 5(five ) microns priming coating to back coat of polyster of 5(five) microns over 5(five) microns primer coating including fixing with screws pre painted iron J or L hooks bolts and nuts 6 mm( six millimeter) diameter of pre painted limpet and rubber washers complete with all accessories as required as per direction of Engineer- in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing pre painted ridges or hips 60cm (sixty centimetre) over all with 0.60 mm ( zero point sixty millimeter) thick pre painted steel sheets in roofing. with hot dipped metallic zinc coated sheets with top coat of regular modified polyster (RNP) organic coating of 20(twenty ) microns over 5 (five)microns primer coating back coat of polyster of 5(five) microns over 5(five) microns primer coating including fixing with screws pre painted iron J or L hooks bolts and nuts 6 mm ( six millimeter )diameter of pre painted G.I limpet and bitumens washers complete with all accessories as required as per direction of Engineer- in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing valley 6cm (Sixty centimetre overall 0.60mm (Zero six zero milimetre)thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat og regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating including fixing with screws, preprinted iron J and L hooks,bplts & nuts & nuts 6mm (Six milimetre)dia and prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals

Providing and fixing M.S.BP Sheet 1.66mm (one point sixty six milimeters)to 2 mm (two milimeters) thick in eves board/facia/soffit/celling as per direction of Engineer- in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing partical board ceiling of approved quality with butt jointing and nail(frame work and cover fillets to be paid for separately ) Cement bonded particle board as per direction of Engineer- in-charge including carriage of materials with in all leads, lifts and other incidentals.

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint.In trusses and trussed purlins in buildings. as Per direction of Engineer- in – charge including carriage of materials with in all leads,lifts, and other

.In trusses and trussed purlins in buildings.

In gratings framed guard bars laddededs railing brackets and similar works

In beams joists,channels angles,tees,flats with connectiong plates or angle cleats as in main and cross beams hip and jack rafters purlins connected to common raffers and the like.

15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded gles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth.in cement morter 1:6 (one cement and six sand) as Per direction of Engineer- in – charge including carriage of materials with in all leads,lifts, and other

15mm Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor two level including arrises,internal ounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth.in cement morter 1:6 (one cement and six sand) as Per direction of Engineer- in – charge including carriage of materials with in all leads,lifts, and other

6mm (six millimeter ) cement plaster to ceiling in cement mortar 1 : 3 (one cement : three sand) including carriage of materials with in all leads, lifts and other incidentals

Applying a birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust,loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of materials with in all leads, lifts and other incidental charges complete in all respect as per direction and Satisfaction of Engineer-in-charge .

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete within all leads , lifts of material and other incidentals .

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including t horoughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface as Per direction of Engineer- in – charge including carriage of materials with in all leads,lifts, and other incidentals . as per Per direction of Engineer- in – charge

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer completed as per direction of Engineer- in – charge

Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete with ready mixed priming pant brushing red leadred oxide chrome as Per direction of Engineer- in – charge including carriage of materials with in all leads,lifts, and other

Painting two costs (excluding priming cost on new steel and other metal surfaces eith enamel paint brushin to give an even shade including cleaning the surface of all dirt,dust and other foregin matters Enamel paint other than white as Per direction of Engineer- in – charge including carriage of materials with in all leads,lifts, and other

Providing plinth protection 50mm (fifty milimeters)thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm nominal size)mechanically mix finishing surface of concrate smoothas Per direction of Engineer- in – charge

Providing under layer for plinth protection of 75mm ( seventy five millimetre ) thick (unconsolidated) bed of dry brick/stone aggregated 40mm nominal size well rammed and consolidated and grouted with fine sand including preparation of ground. including carriage of materials with in all leads, lifts and other incidental as Per direction of Engineer- in – charge

Constructing Course rubblehammer dressed 'U' shape open surface drain with side wall.15x22 cm in cement mortar 1:6 (1 Cement : 6 Sand) and inside plastring with cement plaster 1:3 (1 Cement:3 Sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1 Cement : 5 Sand : 10 graded stone aggregate) of 40 mm nominal size) and 7.5 cm cement concrete 1:2:4 (1 Cement : 2 Sand : 4 Graded stone aggregate of 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design. as Per direction of Engineer- in – charge including carriage of materials with in all leads,lifts, and other incidentals .

Providing ad Laying 8mm(eight milimeters) thick HDF laminated wooden flooring over level CC base complete as per standard design as per the entire satisfaction and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 10mm (Ten milimeters)thick Digital vitrified tiles of size in matt finish 600x600 mm (Six hundredxsix hundred milimeters)in approved shade and colour in flooring,treads of steps and landings laid over 12mm(Twelev milimeters) thick cement mortar1:3 (1 cement : 3 sand) jointedwith cement slurry mixed with pigment to match the shade of tiles as required complete as per the entire satisfaction and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying granite stone in flooring 20mm(average)thickness base of cement mortar 1:3(1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing andpolishing complete. 20mm.thick as per direction and Satisfaction of Engineer-in-charge .

Providing and laying Digital glazed tiles 6 mm (six milimeters) thick in skirting rises of steps and dedo 12 mm (twalve milimeters) thick cement morter 1:3 (one cement :three sand )and jointed with cement slurry as Per entire satisfaction and direction of Engineer- in – charge including carriage of materials with in all leads,lifts, and other incidentals .

Providing and fixing 10mm (Ten milimeters)thick Full body vitrified tiles of size in anti skid 600x600 mm (six hundred x six hundred)in approved shade and colour in flooring,treads of steps and landings laid over 12mm (Towlave milimeters)thick cement mortar1:3 (1 cement : 3 sand) jointedwith cement slurry mixed withpigment to match the shade of tiles as required complete. as per the entire satisfaction and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete.300x16mm (three hundred x sixteen milimeters)

P/F anodized aluminium tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screw etc.the rate is inclusive for carriage of materials within all lead ,lifts as per direction and Satisfaction of Engineer-in-charge .

200x 10mm(two hundered x ten millimetre ).

150x10mm ( one hundred fifty x ten millimetre )

100x10mm( one hundred x ten millimetre )

Providing and fixing ( one hundred twenty five millimetre ) aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals.

125 mm(one hundred twenty five milimetrs)

100 mm(one hundred milimetrs)

75 mm( seventy five millimetre ) dia .

Providing and fixing 100mm (one hundred milimetrs)bright finished brass floor door stopper with rubber cushion screws etc. complete as Per direction of Engineer- in – charge including carriage of materials with in all leads,lifts, and other

Providing and fixing bright finished hard drawn hooks and eyes as Per direction of Engineer- in – charge including carriage of materials with in all leads,lifts, and other

Providing and fixing 62.5 mm x75mm hand rail in 1st class Indian teack wood straight length complete as Per direction of Engineer- in – charge including carriage of materials with in all leads,lifts, and other incidentals.

Providing and fixing flush door shutters core of black board construction with frame of first class hard wood and well matched firtst class Indian teak ply veneering with vertical grains of cross band and face vaneers on one face and commercial ply veneering with vertical grains of cross band on other face of shutters. as per direction and Satisfaction of Engineer-in-charge . 40 mm (forty milimeters)thick including black enamelled M.S. butt hinges.

Providing and fixing 19mm ( nineteen millimetre ) thick Commercial Board in sheleves /box for cup boards with butt joints & fixing with nails & screws etc complete) including carriage of material within all leads, lifts and others incidental charges complete in all respect as per direction and Satisfaction of Engineer-in-charge .

Providing and fixing 19mm (ninteen milimeters)thick water proof commercial board in shelves/box for cup board with butt joints & fixing with nails & screws etc complete)as Per direction of Engineer- in – charge including carriage of materials with in all leads,lifts, and other

Providing and fixing square edges cover fillets (beading) 19mmx6mm (Ninteen x six mm) section i/c mitring at junctions with wood screws and nails complete.Ist class Indian teack wood as Per direction of Engineer- in – charge including carriage of materials with in all leads,lifts, and other

Providing wood work in frames of doors,windows,clerestory,windows and othProviding woodwork in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position.er frames wrought,framed and fixed in position.2nd class deodar wood. as Per direction of Engineer- in – charge including carriage of materials with in all leads,lifts, and other incidentals .

Providing, supplying & fixing of glazed 3 Track -2 Panel Sliding door with Mesh(I 75) made out of multi multi chambered uPVC sections with TPV gasket having isolated drainage and reinforced with Galvanised Iron 120 GSM profiles throughout the window. The sliding cuter frame having overall size of 39x58 mm (thirtyy nnine x fifty eight milimeters)with reinforcement of 2 mm (two milimeters) thickness, sash with overall size of 50 x 82 mm (fifty x eighty two milimeters)with reinforcement of 1.5 mm (one point five milimeters)thickness. Glazing bead for fixing of glass shall be of size 20 x 18 mm(twenty x eigghteen milimeters) and coextruded with gasket. Composition of profile shall consists a minimum of 12 PHR of CaCo3 for every 100 parts of PVC resin. Fiber glass mesh shall be provided in mesh shutter. Window/Door shall be provided with 6 mm plain float glass, standard hardware, multi point locking system of patio espagnolette. wall thickness of frame & shash shall be 2.4 - 2.6mm complete

Providing, supplying & fixing Top hung Ventilator with exhaust fan provision made out of multi chambered uPVC sections with TPV gasket having isolated drainage and reinforced with Galvanised Iron 120 GSM profiles throughout the window. The outer frame having overall size of 60 x 55 mm(sixty xfifty five milimeters) with reinforcement of 1 mm (one milimeters) thickness, mullion with overall size of 74 x 60 mm(seventy four x sixty milimeters with reinforcement of 1 mm (one milimeters) thickness and sash with overall size of 75 x 60 mm (seventy four x sixty milimeters) with reinforcement of 1.5 mm(one point five milimeters) thickness. Glazing bead for fixing of glass shall be of size 34 x 20 mm (thrity four x twenty milimeters)and coextruded with gasket. Composition of profile shall consists a minimum of 6 PHR of TiO2 and not more than 12 PHR of CaCo3 for evry 100 parts of PVC resin. Ventilator shall be provided with 4.5 mm (four point five miliers) Pin Head glass, standard hardware, single point locking and friction stays. Wall thickness of frame, mullion & shash shall be 2.2- 2.4 mm complete as per specification and as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing, supplying & fixing of glazing Openable Door made out of multi multi chambered uPVC sections with TPV gasket having isolated drainage and reinforced with Galvanised Iron profiles throughout the window. The outer frame having overall size of 60 x55 mm(sixty x fifty five milimeters) with reinforcement of 1 mm (one milimeters)thickness, sash with overall size of 102 x 60 mm(one hundred zero twox sixty milimeters) with reinforcement of 1.5 mm (one point five milimeters)thickness. Glazing bead for fixing of glass shall be of size 34 x 20 mm(thirty four x twenty milimeters) and coextruded with gasket. Composition of profile shall consists a minimum of 6 (six)PHR of CaCo3 for every 100 parts of PVC resin. Doors shall be provided with 6 mm plain float glass, standard hardware, multi point locking system and 3D hinges wall thickness of frame, mullion & sash shall be 2.2 to 2.4 mm (two point two to two point four)complete as per specification and as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Glazing with glass panes of 5.50mm (five point fifty milimeters)thickness (weight not less than 13.75 kg/ sqm.complete as per specification as Per direction of Engineer- in – charge including carriage of materials with in all leads,lifts, and other incidentals .

WS&SI Excavation in drains and channels etc. in earth work in all kind of soil such as pick work jumPer work pick jumPer work ,blastreing work ,hard and soft blastering ,saturator soil including chiseling or any other mixed variety of soil ,lift up to any hight. as Per direction of Engineer- in – charge including carriage of materials with in all leads,lifts, and other incidentals .

Providing and fixing 15 mm (fifteen millimetre) nominal bore to wall ceiling and floor galvanized mild steel tube (medium grade) tube fittings and clamps including making good the wall ceiling and floors including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Plytheline – Aluminium -Polyethylene (PE-AL-PE) omposite pressurepipe U.V. stabilized with carbon blackconfirming to IS-15450-2004 water supplyincluding clamp at one metre spacing, cutting,fixing and making good the wall etc. butexcluding the cost of fittings (internal work)pipes exposed on wall.1216 (16 mm( sixteen millimetre ) O.D. pipe) including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing vitreous China wash down, water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(one cement : one sand) (Seat and cover to be measured and paid for separately) Ordinary closet including carriage of material with in all leads, lifts and others incidentals .

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers white plastic seat and cover including carriage of material within all leads , lifts of material and other incidentals .

high density polyethylene / poly propylene 10litres capacity ( full flush) uropean standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) including carriage of material within all leads , lifts of material and other incidentals .

Providing and fixing PTMT jet spray of approved quality and colour with 1.5 mtr. ( one point five metre ) Tube including carriage of material within all leads , lifts of material and other incidentals .

Providing and fixing 32mm ( thirty two millimetre ) nominal bore C.P. brass flush pipe /spreaders for urinal with fitting such as unions,clamps etc. (all in C.P. Brass) including cutting holes and making good the same including carriage of material within all leads, lifts and others incidentals .

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings Flat back 550mm x 400mm (five hundred fifty millimetre x four hundred millimetre ) including carriage of material within all leads, lifts and others incidentals .

Providing and fixing 610 x460 mm ( six hundred ten x four hundred sixty millimetre ) with bowl depth 200 mm.( two hundred millimetre ) stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding including carriage of material within all leads, lifts and others incidentals . fitting.

Providing and fixing vitreous China pedestal of approved specification /make for wash basin complete recessed at the back for the reception of pipes and fittings including carriage of material with in all leads, lifts and others incidentals .

Providing and fixing 32mm( thirty two millimetre ) dia C.P. Brass waste for wash basin or sink including carriage of material with in all leads, lifts and others incidentals .

Providing and fixing 600mm x 450 mm ( six hundred x four hundred fifty millimetre ) bevelled edge mirror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P.Brass screws and washers.including carriage of material within all leads , lifts of material and other incidentals .

Providing and fixing 600mm x 20mm ( six hundred x twenty millimetre ) C.P. Brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws .including carriage of material within all leads , lifts of material and other incidentals .

Providing and fixing 600mm x 120 mm ( six hundred x one hundred twenty millimetre ) glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws including carriage of material within all leads , lifts of material and other incidentals .

Providing and fixing liquid soap container with C.P. Brass lid and brackets fixed to wooden plugs with C.P. Brass screws Glass container including carriage of material within all leads , lifts of material and other incidentals .

Providing and fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws small 160mm one hundred sixty millimetre ) size including carriage of material within all leads , lifts of material and other incidentals .

Providing and fixing 15mm ( fifteen millimertre ) dia brass bib tap (Superior or heavy type) including carriage of material within all leads , lifts of material and other incidentals .

Providing and fixing 15 mm dia ( fifteen millimetre) dia metre C.P Brass pillar tap heavy duty with Capstan head including carriage of material within all leads, lifts and others incidentals .

Providing and fixing 15mm( fifteen millimetre) dia C.P. stop cocks including carriage of material within all leads, lifts and others incidentals .

Providing and fixing 15 mm ( fifteen millimetre) nominal bore PTMT concealed stop cock with flange of approved quality and colour including carriage of material within all leads, lifts and others incidentals .

Providing and fixing 15 mm ( fifteen millimetre) nominal bore P.V.C connection with brass unions 300/450mm ( three hundred / four hundred fifity millimetre ) length including carriage of material within all leads, lifts and others incidentals .

Providing and fixing 32mm ( thirty two millimetre ) nominal bore to wall ceiling and floor plug for glazed ware sinks, basins, etc. with long screwed shank and fly nut and fixed to steel pipe including vulcanite plug, brass chain and stud including carriage of material within all leads, lifts and others incidentals .

Providing and fixing brass ball valve (horizontal plunger type) including carriage of material within all leads, lifts and others incidentals .

15mm ( fifteen millimetre ) nominal bore

20mm ( twenty millimetre ) nominal bore

Providing and fixing G.I./M.I Union of following sizes (where not included in the items including carriage of material within all leads, lifts and others incidentals .

15mm ( fifteen millimetre ) nominal bore

20mm ( twenty millimetre ) nominal bore

Providing and fixing 15mm( fifteen millimetre ) nominal borePVC water storage tankof ISI : 12701 marked, G.I. inlet and outlet connection, ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level including carriage of material within all leads, lifts and others incidentals .

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including carriage of material within all leads, lifts and others incidentals .

Providing and fixing high pressure PVC spigot and socket , waste and ventilating pipes ISI marked including jointing with approved adhesive etc. including carriage of material within all leads, lifts and others incidentals .

150 mm( one hundred fifty millimetre ) dia

110 mm( one hundred ten millimetre ) dia

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm ( three millimetre ) thick bolts and nuts complete including fixing with approved adhesive etc. complete including carriage of material within all leads, lifts and others incidentals .

110 mm( one hundred ten millimetre ) dia

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm ( three millimetre ) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage of material within all leads, lifts and others incidentals .

110 mm( one hundred ten millimetre ) dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete including carriage of material within all leads, lifts and others incidentals .

110 mm( one hundred ten millimetre ) dia .

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of material within all leads, lifts and others incidentals .

110 mm( one hundred ten millimetre ) dia .

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of material within all leads, lifts and others incidentals .

110 mm( one hundred ten millimetre ) dia .

75 mm( seventy five millimetre ) dia .

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers,connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc.including carriage of material within all leads, lifts and others incidentals .

Equal Tees 1216

Reducing Tees 1620x all branches.

Female brach Tees 1216x1216x15mm thread.

Femail elbows 1216x15 mm thread

Male thread connector 1216x15 thread.

1216x15mm thread.

Couplers 1216

Reducers 1620.1216

Constructing manhole with RCC top slab 1:2:4 mix ( one cement : two approved sand :four graded crushed stone aggregate 20mm ( twenty millimetre ) nominal size ) foundation concrete 1:4:8 ( one cement : four sand :eight graded stone aggregate 40mm ( forty millimetre ) nominal size) and inside plastering 15mm ( fifteen millimetre ) thick with cement mortar 1:3 (one cement three sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix ( one cement two sand :four graded stone aggregate 20mm ( twenty millimetre ) nominal size ) finished smooth complete including curing and testing . Inside size 800mm x800mm x and 500mm (eight hundred x eight hundred x five hundred millimetre ) deep including C.I cover with frame (light duty single seal pattern -1) 455 x610mm ( four hundred fifty five x six hundred ten millimtre ) internal dimensions total weight of cover and frame to be not less than 38kg. ( thirty eight kilogram ) (weight of cover 23 kg (twenty three kilogram ) of frame 15kg (fifteen kilogram) . With 300mm (three hundred millimetres ) thick walls of square rubble masonary in cement mortar 1:3 (one cement : three sand .) complete in all respect including carriage of material within all leads , lifts of material and other incidentals .

LABH CHAND

umesh Kumar

MANOJ KUMAR

Abhishek Gupta